Users Guide: iMFD Sensor Module

iMFD Sensor Module SM-Vac/Boost

Version 1.0 February 9, 2007

*Please read the instructions completely through at least once before proceeding with the
installation to minimize errors.

*Double check polarity of power before powering it on for the first time.

Overview:

(Figure 1)

1. Connects to 12V-18V power source

2. Analog outputs (0-5V linear output)
3. Termination jumper. Closed for first SM in iMFD daisy chain.
4. Connects to next SM in iMFD daisy chain or to first DM
5. Connects to previous SM or unconnected if first SM in iMFD daisy chain
6. Connects to vacuum hose from intake manifold.

Install the Vacuum Hose:

1. The SM-Vac/Boost module has a 3 bar MAP sensor built-in. Connect a 1/8” vacuum hose to the sensor shown above #6
2. For high boost application 15PSI and up, it is a good idea to install a zip tie around the vacuum hose to prevent it from
coming lose.

Connecting Power to the Unit:

CAUTION! CONNECTING THE SM-Vac/Boost IN REVERSE POLARITY

WILL DAMAGE THE UNIT! CHECK CONNECTIONS BEFORE POWERING
ON.
1. The SM-Vac/Boost accepts 12-18V DC for power. Connect the negative wire (black) to your vehicle’s ground. This is usually
the negative terminal of your automobile’s battery. Connect the positive wire (red) to your vehicle’s ignition power. This
power is only supplied when your key is turned passed a specific position and is off when your key is removed. Your power
connection must be capable of supplying at least 1 amp of current. A 5 Amp fuse is recommended for safety.

*If you plan to integrate the SM-Vac/Boost with other aftermarket devices by utilizing the analog output signal wire. Make sure that
the negative wire (black) is connected as close as possible to your device's ground. This guarantees that both devices "see" the same

Version 1.0 February 9, 2007

www.plxdevices.com
(408)745-7591
 Users Guide: iMFD Sensor Module

reference ground and a more accurate interpretation of the output voltages will be achieved. Please refer to the PLXApp notes online
for more information.

2. Locate the 2.1mm Power plug. Unscrew the plastic cover and insert it into the red/black power wires.
3. Solder or crimp the red power wire to the CENTER of the connector. (12-18V)
4. Solder or crimp the black power wire to the SHIELD of the connector. (GROUND)

(Figure 2)

Using the Sensor Module in the iMFD Chain:

1. If the SM-Vac/Boost is the only sensor module or last sensor module in the iMFD chain, be sure to have the termination
jumper installed. Otherwise, remove the jumper. Please refer to (Figure 1) for the location of the termination jumper.

(Figure 3)

Using the Sensor Module Analog Output:

1. The SM-Vac/Boost has one 0-5V analog output designed to be interfaced with a number of aftermarket products such as
engine management systems, data loggers and tuning electronics. It is not mandatory for you to use this output for your
unit to properly function.

(Figure 4)

Linear Analog Output (0-5V)

Version 1.0 February 9, 2007

www.plxdevices.com
(408)745-7591
 Users Guide: iMFD Sensor Module

(Figure 5)

Vacuum Range (0V = 30.5inHg = -15PSI, 1.66V = 0PSI)

Boost Range (1.66V = 0PSI, 5.0V = 30PSI)

Recommended Accessory:

(Figure 6) DM-5 Vac/Boost 52mm Gauge. Ideal for affordable vacuum and boost
monitoring from your SM-Vac/Boost

Included Items:

1. SM-Vac/Boost main unit

2. 4ft red power wire
3. 4ft black ground wire
4. 4ft gray analog output wire
5. 2.1mm power connector
6. 4 pin Molex connector with 4 terminals for analog output
7. 1ft Serial Cable
8. Termination jumper
9. Users Guide

Version 1.0 February 9, 2007

www.plxdevices.com
(408)745-7591
 Users Guide: iMFD Sensor Module

Specifications:

Physical Dimensions 2" x 2.875" x 1.125" (52mm x 75mm x 28mm) L x W x H

Accuracy <0.25 PSI
Measurement Range 30.5inHg - 30 PSI (760mmHg - 2.11kg/cm^2)
Analog Outputs Linear 0-5V (Driving Current 20mA)
Operating Voltage 8V-18V
Power Consumption 0.3 Watts
Operating Temperature 0 - 85 Deg C
Sensors 3 Bar MAP sensor
Enclosure Extruded Aluminum

TERMS OF USE

PLX Devices Inc. does not guarantee the Sensor Module functionality with any ECU, data logger or other devices that uses the output
signals. Implementation and integration of the Sensor Module with any other device(s) must be done at your own risk. Improper
installation and usage may lead to engine damage. Mount and install the Sensor Module in a location where it does not obstruct the
driver’s view and/or ability to safely control the vehicle.

LIMITED WARRANTY

PLX Devices Inc. warrants this product to be free from defects for 90 days from the date of purchase. If applicable, Oxygen sensors
and other non-serviceable items are excluded from stated warranty. Serviceable goods must be determined by PLX Devices to be
defective before any warranty or replacement is issued. PLX Devices’ obligation under warranty shall be limited to repairing or
replacing, under the discretion of PLX Devices, any part proven defective. This warranty is limited to the repair or replacement of
parts in the manufactured good and the necessary labor done to affect its repair or replacement.

SERVICE UNDER WARRANTY

In the unlikely event that your PLX Devices hardware should fail during the warranty period, a Return Material Authorization number
(RMA) must be first retrieved from PLX Devices Customer Support. Support can be contacted through email: [email protected]
or by phone: 408-745-7591. All serviceable goods must be packaged securely with proof of purchase, RMA number, with all shipping
charges prepaid and shipped to PLX Devices Inc. Goods returned under warranty must be received by PLX Devices Inc. within ten
(10) business days after the RMA number has been issued. Goods received after this period is subject to fees for the service of repair
or replacement. All repaired or replaced items shall be warranted for the remainder of the original product warranty.

RETURNS AND RESTOCKING FEE

A 15% restocking fee will apply to applicable PLX Devices products for refund. All returns are to be packed in original condition
including packaging, documentation, manuals, and accessories. Returns that do not include all the accessories and components may
be returned to the customer or charged on a per item basis. The customer assumes responsibility for product until receipt at PLX
Devices Inc., shipping via an insurable carrier is recommended. Any unauthorized shipping charges will be billed to the customer or
shipment will be refused.

DISCLAIMER

PLX Devices Inc. shall not be liable for direct, special, incidental, or consequential damages resulting from any legal theory including,
but not limited to, lost profits, downtime, goodwill, damage, injury to persons, or replacement of equipment and property due to
improper installation, integration and/or misuse of any PLX Devices Inc.’s product(s). This warranty applies to the original purchaser
of product and is non-transferable. All implied warranties shall be limited in duration to the said 90 day warranty period.

Revision History
Version 1.0 (2/9/07) Initial release

Version 1.0 February 9, 2007

www.plxdevices.com
(408)745-7591