N I T R O G E N P U M P I N G EQ U I P M E N T

Well served.

Equipped with high pressure nitrogen pump, vaporizer system and all instruments and control switches
as required by site, the PNS-180K nitrogen pump skid is used to supply normal temperatue high pressure
nitrogen gas for oilfield downhole operations. It is a cryogenic unit that pumps extremely cold liquid
nitrogen (-196°C, -320°F) and converts it to a usable gas (Max. 60°C, 140°F). A heat recovery system raises
the temperature of the liquid nitrogen to 15 ºC～40ºC changing it to a gas at the vaporizer pot.

The SJS nitrogen pump and vaporizer system consist of the following components:
• A diesel engine that provides power for the hydraulic pumps.
• Hydraulic pumps and motors that hydraulically transfer the power by the engine to other system components.
• A centrifugal boost pump.
• A high-pressure triplex pump.
• A water bath type vaporizer pot.
• A control system contained within a panel.Heat recovery

PNS-180K

G E N E R A L S P EC I F I C AT I O N

Physical Dimensions 4500mm(L)X2300mm(W)X2550mm(H)

Pressure Range Maximum working pressure 69 MPa (10000 psi)
Max. Flow Rate 122 L/min. (Liquid Nitrogen) 180,000 SCFM (85.0 SCMM)
Discharge Temperature 15° C - 40° C
 N I T R O G E N S TO R A G E U N I T
Well served.

The unit is designed for storing cryogenic liquid(liquid nitrogen), and made, tested and approved
according to 《cryo heat insulation and pressure vessel》 and 《rules of cryogenic liquid storing and
transporting》. Storage tank uses vacuum and multi-layers for heat insulation. The inner vessel is made of
0Cr18Ni9, and outer vessel material is 16MnR.
Gauges, valves and safety accessories are mounted at tank side and convenient for management and use.

G E N E R A L S P EC I F I C AT I O N

item unit parameter

Inner vessel Outer vessel
Vessel sort Third category ——
Storage medium LN2 ——
Working pressure MPa 0.69 vacuum
Design pressure 0.83 -0.1
Hydraulic testing pressure 1.21 ——
Gas tightness testing pressure 0.83
Blowoff pressure of safety valve 0.73
Burst pressure of burst plate 1.21
Working temperature °C -196

Design temperature -196

Actual volumn m3 7.03
Outside volume 7.4
Tank material 0Cr18Ni9 16MnR
Barrel Design thickness mm 7.62 5.07
Seal head design thickness 7.61 6.95
Corrosion allowance 0 1
Welded joint coefficient 1 0.85

Evaporation rate per day % ≤0.40 (LN2)

Empty tank mass（±5%） kg 4480

Load mass LN2 kg 5680

Loading coefficient 95%

Max. mass kg 10160

Insulation method Fine vacuum and multi-layers

size（L X W X H） mm 2991 X 2438 X 2635

Crash Frame and lifting tools DNV certification

 ACID MIXING SKID
Well served.

Model AMS-100 Acid Mixing Skid developed by SJS Ltd. Company is the most advance, accurate computer
controlled acid mixng system available. Various kinds of liquid additives, dry additives and acid liquids
can accurately mix and boost fluids to high-pressure plunger pumps. Its successful acidizing applications
in oilfields have proved it an ideal choice.
The acid mixing skid permits monitoring and automatic control of tub level. Hydraulic driven components
can accurately mix and boost fluids to high-pressure pumps.

A M S - 100

G E N E R A L S P EC I F I C AT I O N

Net Weight ≤21 T The AMS-100 Acid Mixing Skid includes the
Overall Dimensions 9.0 m(L) X 2.5 m(W) X 3.0 m(H) following components:
Mixing Tank 2 M3
• Two(2) engine
Max. displacement 15.9 M3/Min (100BBL)
of Acid Fluid • Two(2) pump drive
Discharge pressure 0.45 MPa • One(1) SCP12X10X22 anti-corrosion discharge
of Acid Fluid
centrifugal pump
Liquid Additive 10-40 L/Min
System 20-100 L/Min • One(1) 250UHB-DZ-Z-650-45 acid pump
40-400 L/Min • One(1) SCP 10X8X14 clean water pump
Dry Additive System 3-30 L/Min
• One(1) mixing system
Operating -20° C - 50° C
Temperature • One(1) hydraulic system
• Three(3) liquid additive systems
• Two(2) dry additive systems
• One(1) manifold with anti-corrosion lining
• One(1) control system
 A C I D F LU I D S U P P LY P U M P S K I D
Well served.

The ATS-20 Acid Fluid Supply Pump Skid is designed independently of SJS Limited. It mainly consists of
power system, mechanical clutch, transmission shaft, acid-proof centrifugal pump, inlet & outlet pipelines
and skid.

AT S - 20

G E N E R A L S P EC I F I C AT I O N

Net Weight ≤3 T
Overall Dimensions 3.5 m(L) X 1.5 m(W) X 1.7 m(H)
Max. displacement of Acid Fluid 20BBL/Min @ 60PSI
Discharge pressure of Acid Fluid 60PSI
Operating Temperature -20° C - 55° C
 A C I D F LU I D S U P P LY P U M P S K I D
Well served.

The ATS-100 Acid Fluid Supply Pump Skid is designed independently of SJS Limited. It mainly consists of
power system, mechanical clutch, transmission shaft, acid-proof centrifugal pump, inlet & outlet pipelines
and skid.

AT S - 100

G E N E R A L S P EC I F I C AT I O N

Net Weight ≤8 T
Overall Dimensions 5 m(L) X 2.3 m(W) X 2.25 m(H)
Max. displacement of Acid Fluid 100BBL/Min @ 60PSI
Discharge pressure of Acid Fluid 80PSI
Operating Temperature -20° C℃ - ～ 55° C℃
 B AT C H M I X I N G S K I D
Well served.

This product is mainly used for continuous mixing and batch mixing of water, dry bulk cement and
additives to prepare a cement slurry with a certain density and a certain discharge rate to satisfy the needs
of various special processes related to cementing operation in oilfields.
This product is a skid-mounted cement slurry mixing unit. It is powered by one CAT C9 engine and
one FUNK transfer case to drive three hydraulic pumps to provide power for two agitators and two 6x5
centrifugal pumps. All operations are centralized on the control console on an operation platform for ease
of operation. To guarantee the mixing quality, this unit is designed for mixing by agitators and recirculation
by centrifugal pumps.

B C S - 300- 10 0 A
G E N E R A L S P EC I F I C AT I O N

Description Model/Size/Specs
Cement Slurry Density Control Mode Manual
Skid Frame Structure Wholly welded, c/w anti-collision frame, lifting points and forklift slots.
Engine CAT C9 300 HP@2200 rpm, one
Transfer Case FUNK 593 (0.836:1), one set
Centrifugal Pumps SERVA SCP 6x5x11, two sets
Fuel Tank Capacity 250 L
Max. Discharge Pressure 0.49 MPa (70 psi)
Max. Discharge Rate 3.7 m3/min
Low Pressure Manifold Stainless steel
Data Acquisition System Control box c/w DAS interface
Batch Mixing Tanks 2X50 BBL, stainless steel
Slurry Density Range 1.3 - 2.5 g/cm3
Working Temperature Range -20°C +55°C
Interfaces Water Suction Port: 4” FIG.206 female union
Drain Port: 4” FIG.206 female union
Discharge Port: 4” FIG.206 female union
Overall Dimensions, LxWxH 7,800 mm x 2,500 mm x 3,200 mm
Dry Weight 14,000 kg (approx.)
 DOUBLE PUMP ACIDIZING SKID
Well served.

This PSS-621B double pump acidizing skid is a new generation of acidizing unit developed based on the
SERVA TPD600 oilfield-purpose triplex plunger pump and many SERVA patents. It is mainly comprised of
engine, transmission, TPD600 pump, hydraulic system, air system, pump lubrication system, high and
low pressure manifolds, electrical system and control system, etc. It is basically designed for acidizing
operation, pressure testing and pumping of other fluids. It is suitable for various acidizing operations in
deep, intermediate depth and shallow oil and gas wells.

P SS - 621 B

G E N E R A L S P EC I F I C AT I O N B A S I C PA R A M E T E R S

Engine CAT C15, 540 HP@2100 RPM, 2 sets Pressure Range Max. Working Pressure to 73.2 MPa (10394 psi)
(equipped with 3 1/2" fluid end)
Transmission ALLISION 4700 OFS, 2 sets
Max. Displacement 2.54 m3/min (equipped with two 3 1/2" fluid
Plunger Pump SERVA TPD600X3 1/2", 2 sets ends)
Booster Pump SERVA 6X5 (acid proof centrifugal pump), 2 sets Temperature Range -20°C - 55°C

Displacement Tank 2X10 BBL, stainless steel Overall Dimensions 6,700 mm (L) X 2,600 mm (W) X 3,100 mm (H)

Net Weight 20,000 kg

 FRAC PUMPER SKID
Well served.

This PGS-2500A frac pumper skid is a new generation of fracturing unit developed based on the SERVA
QPA2500 oilfield-purpose quintuplex plunger pump and many SERVA patents. It is mainly comprised of
engine, transmission, QPA2500 pump, hydraulic system, air system, pump lubrication system, high and
low pressure manifolds, electrical system and control system, etc. It is basically designed for hydraulic
fracturing, acid fracturing, well pressure testing and pumping of other fluids. It is suitable for various
fracturing operations in deep, intermediate depth and shallow oil and gas wells.

P G S - 2500 A

G E N E R A L S P EC I F I C AT I O N B A S I C PA R A M E T E R S

Engine CAT 3512C, 2500 HP@1900 RPM, 1 set Pressure Range Max. Working Pressure to 67.6 MPa (9795 psi)
(equipped with 5" fluid end)
Transmission CAT TH55-E70, 1 set
Max. Displacement 4.247 m3/min (equipped with two 5" fluid ends)
Plunger Pump SERVA QPA2500x5", 1 set
Temperature Range -20°C - 60°C

Overall Dimensions 9,750 mm(L) X 2,500 mm(W) X 3,300 mm(H)

Net Weight 30,000 kg

 DATA ACQUISITION & CONTROL UNIT
Well served.

This skid mounted computerized data acquisition & control unit (Data Van), a centralized control and
commanding center, is suitable for full-process monitoring and control of oil/gas well acidizing and
fracturing operations by means of remote control through a network. All data can be real-timely collected,
displayed and recorded. These data can be processed, saved and printed in forms of data and curves.

B A S I C PA R A M E T E R S

Skid Frame In compliance with DNV 2.7.1 Standard

Weight Tare: 7820 KG

Payload: 4180 KG (Control System)
MGW: 12000 KG
Overall Dimensions 6,058 mm x 2,438 mm x 2,591 mm
(20” Container)

Main Configuration:
• Container structure with walls filled with rock for thermal
insulation;
• One set of 12.4 KVA diesel engine driven power generator;
• Two sets of air conditioners for T3 high temperature working
condition;
• One set of SERVA Pump Skid Remote Control System
• One set of SERVA Data Acquisition System

P U M P S K I D R E M OT E CO N T R O L S YS T E M

The Multi-Pump Control System is a PC-based software system SINGLE PUMP MAIN SCREEN
developed on the SERVA automatic control system. It is designed
on the Window application program to control multiple pumps or
multiple types of pumper units with different controllers.
Main Functions:
• Supporting control and operation of a complete pumper
truck;
• Supporting configuration and calibration of various signals;
• Supporting self-defined settings of alarms;
• Supporting auto prompting of alarms; P U M P G R O U P CO N T R O L S C R E E N
• Providing system settings function;
• Supporting control of pump control equipment with different
controllers;
• Supporting simultaneous control of multiple pumps;
• Auto monitoring of master control commands;
• Providing grouping control of pump control equipment.

P U M P G R O U P CO N T R O L S C R E E N
 DATA ACQUISITION & CONTROL UNIT
Well served.

D ATA A CQ U I S I T I O N S YS T E M

This SERVAview for FRAC is a software program developed

on Microsoft WINDOWS. It is designed for monitoring data
acquisition in the processes of acid fracturing/sand control
performed by downhole service companies in the oilfields. It is
capable of performing real-time data acquisition, monitoring and
recording of data on job sites; helping site technicians control
the job data precisely; analyzing the job state; commanding
the site job operations; guaranteeing the job quality; and
troubleshooting any problem occurred in the job processes
timely.
The SERVAview for FRAC supports the following operations:
• Real-time data acquisition and data recording;
• Free configuration of signals and introduction of Software Features
computational formula;
The SERVAview for FRAC data acquisition software has the
• Custom-defined and flexible split-screening of curves and following features:
numerical values;
• Real-time editing and modification of curves; Basic functions
• Compatible to a third-party analysis software such as • Multipath signal acquisition at each connecting
FracproPT. point through data acquisition devices and industrial
Ethernet;
• Providing grouping control of pump control equipment.
• Applicable to the operating systems: Windows XP and
Windows 7

Data acquisition/collection and storage

• Free configuration of signals;

• Real-time editing of curves;
• Real-time calibration of data;
• Data filtering and fine tuning;
• Real-time switchover of data in Metric and imperial
systems.

Display
• Real-time curve settings such as color, measuring
range, line width, etc.;
• Display of curves and numerical values in vivid split
screens;
• Flexible display of curve time to enable random
adjustment of curve display time in the real-time data
acquisition and history data replay;
• Custom-defined display to enable free custom-made
display of data and curves