SF

I Ia
RDL 1.25 0.9 DC EV
RLL 1.750006 1.75000598 Strngth I 1.25 1.35
Pav 1.349977 1 Strngth Ia 0.9 1
ppv 1.349977 1
qsv 1.349821 1
qlv 1.350334 1
brf 1.750031 1.75 label B H
wl 0 0 w1 1.2 1.2
CR,sh,tu 0.5 1 w2 0.4 9.65
pah 1.500021 0.90002982 w3 3.8 0.35
pph 1.5 0.9 w4 0.28 1.45
qsh 1.500248 0.9 w5 3.4 8.5
qlh 1.499848 0.89990873 w6 3.4 1.2
w7 3 1.2
w8 3.4 8.5
w9 3.4 1.8
w10 3 10.3
W11 1.2 1.8
W12 1.2 1.5

Factored Forces(
unfactored loads strength I)
w1 36 45
w2 92.6399999999999 115.8
w3 33.25 41.5625
w4 10.15 12.6875
w5 346.8 433.5
w6 102 127.5
w7 90 112.5
vertical Loads

w8 520.2 650.25
w9 110.16 137.7
w10 556.2 695.25
W11 38.88 48.6
RDL 835.884 1044.855
RLL 977 1709.75
pav 739.01 997.6635
ppv 81.68 110.268
Qsv 0.787 1.06245
Qlv 3.188 4.3038
 Total 4573.829 6288.25275
Brf 162.5 284.375

Horizontal Loads
wl 18.59 0
CR-SH-TU 83.58 41.79
pah 739.01 1108.515
pph 98.1 147.15
Qsh 0.945 1.4175
Qlh 3.685 5.5275
Total 1106.41 1588.775

stability and safety criteria

1.Eccentricity

V ∑M xo=∑M/V e=B/2-xo
Strength I 6288.253 21772.02 3.46233165484641 0.53766834515
Strength Ia 5029.363 16445.48 3.26989355589513 0.7301064441

2. Sliding
v tan(ẟ) Fr=V*tan(ẟ) ϕFr
Strength I 6288.253 0.33 2075.1234075 977.878867844
Strength Ia 5029.363 0.33 1659.689658 782.110325522

3. Bearing capacity
Hn Vn Hn/Vn ϕ*RI*qult
Strength I 1588.775 6288.253 0.25265762417072 104.351533029
Strength Ia 1125.521 5029.363 0.2237899888149 104.351533029

Assuming the maximum bearing capacity acts as load

3 1.2
1.45
113.511886224
8m

check depth for wide beam shear

d 1392 mm
V left 182.52711305 kn
V right -21.794282155 kn no need of checking since negative
𝑣_𝑐=0.25𝑓_𝑐𝑡𝑑 𝑘_1 𝑘_2 𝑏_𝑤 𝑑
fctd 1.0315288196
k1 1.0833333333
k2 1
bw 1
 Vc 388.886365 Kn > vleft ok

critical section for moment is on the left side and at the face of the abutment
Msd 510.80348801 kn-m/m
b 1000 mm
d 1392 mm
µsd 0.0232672724
Kz 0.9882277786
AS 1423.4235507 mm2
AS,min 2320 mm2 >AS provide minimum reinf.
s 135.34482759 mm using diameter 20 bar
s provide 130 mm
Transverse or shrinkage and temperature
𝐴_𝑠2≥{█(0.2∗𝐴𝑠@𝐴𝑠,𝑚𝑖𝑛)┤

0.2*AS 464
AS,min 2320
s 135.34482759 mm using diameter 20 bar
s provide 130 mm

Therefore provide minimum reinforcing in both directions with diameter 20 at 130 mm spacing
EH LL BR LS WS WL CR+SH+TO
1.5 1.75 1.75 2 0 0 0.5
1.5 1.75 1.75 2 0 0 0.5

γ W x W*x h1 8.5
25 36 0.6 21.6 B1 3.4
24 92.64 1.4 129.696 B2 0.4
25 33.25 1.4 46.55 BL1 3
25 10.15 1.46 14.819 BL3 1.2
24 346.8 2.73333333 947.92 Bf1 0.35
25 102 4.53333333 462.4 x 0.28
25 90 6.5 585 ht 1.2
18 520.2 3.86666667 2011.44 B 8
18 110.16 3.3 363.528
18 556.2 6.5 3615.3
18 38.88 0.6 23.328
9.81 17.658

Factored Moment factored factored

Forces( stre Arm unfactored moment(streng moment(streng
ngth Ia) moment th I) th Ia)
32.4 0.6 21.6 27 19.44
83.376 1.4 129.696 162.12 116.7264
29.925 1.4 46.55 58.1875 41.895
9.135 1.46 14.819 18.52375 13.3371
312.12 2.733333 947.92 1184.9 853.128
91.8 4.533333 462.4 578 416.16
81 6.5 585 731.25 526.5
468.18 3.866667 2011.44 2514.3 1810.296
99.144 3.3 363.528 454.41 327.1752
500.58 6.5 3615.3 4519.125 3253.77
34.992 0.6 23.328 29.16 20.9952
752.2956 1.26 1053.21384 1316.5173 947.892456
1709.75 1.26 1231.02 2154.285 2154.285
739.01 8 5912.08 7981.308 5912.08
81.68 0 0 0 0
0.787 8 6.296 8.4996 6.296
3.188 8 25.504 34.4304 25.504
5029.3626 59.41333 16449.6948 21772.01655 16445.480356
284.375 10.05 1633.125 2857.96875 2857.96875
0 10.05 186.8295 0 0
83.58 7.335766 613.123358 306.561678832 613.123357664
665.109 3.35 2475.6835 3713.52525 2228.11515
88.29 1 98.1 147.15 88.29
0.8505 3.654545 3.45354545 5.18031818182 3.10819090909
3.3165 3.654545 13.467 20.2005 12.1203
1125.521 39.09486 5023.7819 7050.58649701 5802.72574857

emax=b/4 Design margin

2 73.11658
2 63.49468

HL Design margin
1588.775 62.47155
1125.521 43.90821

ϕ 0.5
qmax Design margin RI 0.417406
113.511886 8.77836 qult 500
96.1300902 7.878603

kn/m
at 130 mm spacing