SLOVENSKI STANDARD

SIST ISO 4026:

01-DSULO-

1DYRMQL]DWLþL]QRWUDQMLPãHVWHURNRWRPLQSRVQHWRNRQþLQR

Hexagon socket set screws with flat point

Vis sans tête à six pans creux, à bout plat

iTeh STANDARD PREVIEW
(standards.iteh.ai)
Ta slovenski standard je istoveten z: ISO 4026:1993
SIST ISO 4026:2000
https://standards.iteh.ai/catalog/standards/sist/df34b863-9319-464a-9bbd-
8359b42c1370/sist-iso-4026-2000
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs

SIST ISO 4026: en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
 SIST ISO 4026:1996

iTeh STANDARD PREVIEW

(standards.iteh.ai)
SIST ISO 4026:2000
https://standards.iteh.ai/catalog/standards/sist/df34b863-9319-464a-9bbd-
8359b42c1370/sist-iso-4026-2000
 SIST ISO 4026:1996

INTERNATIONAL ISO
STANDARD 4026
Second edition
1993-12-15

Hexagon socket set screws with flat Point

Vis sans t&e a six pans creux, a bout plat

iTeh STANDARD PREVIEW
(standards.iteh.ai)
SIST ISO 4026:2000
https://standards.iteh.ai/catalog/standards/sist/df34b863-9319-464a-9bbd-
8359b42c1370/sist-iso-4026-2000

Reference number
ISO 40269 993(E)
 SIST ISO 4026:1996

IISO 4026:7993[E)

Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(1EC) on all matters of electrotechnical standardization.

Draft International Standards adopted by the technical committees are

circulated to the member bodies for voting. Publication as an International
iTeh STANDARD PREVIEW
Standard requires approval by at least 75 % of the member bodies casting
a vote.

International Standard
(standards.iteh.ai)
ISO 4026 was prepared by Technical Committee
lSO/TC 2, Fasteners.
SIST ISO 4026:2000
This second edition https://standards.iteh.ai/catalog/standards/sist/df34b863-9319-464a-9bbd-
cancels and replaces the first edition
(ISO 4026:1977), which has been technically 8359b42c1370/sist-iso-4026-2000
revised.

Annex A forms an integral patt of this International Standard.

0 ISO 1993
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronie or mechanical, including photocopying and
microfilm, without Permission in writing from the publisher.
International Organkation for Standardization
Case Postale 56 0 Cl-l-1 21% Geneve 20 0 Switzerland
Printed in Switzerland
 SIST ISO 4026:1996

INTERNATIONAL STANDARD 0 ISO ISO 4026:1993(E')

Hexagon socket set screws with flat Point

1 Scope

This lnternational Standard specifies the characteristics of hexagon socket set screws with flat Point and threads
from Ml,6 up to and including M24 and of product grade A.

If, in special cases, specifications other than those listed in this International Standard are required, they should
be selected from existing International Standards, for example ISO 261, ISO 888, ISO 898-5 and ISO 965-2.

2 Normative referencesiTeh STANDARD PREVIEW

The following Standards (standards.iteh.ai)
contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All Standards are subject to
revision, and Parties to agreements based on SIST ISO 4026:2000Standard are encouraged to investigate the possi-
this International
bility of applying the mosthttps://standards.iteh.ai/catalog/standards/sist/df34b863-9319-464a-9bbd-
recent editions of the Standards indicated below. Members of IEC and ISO maintain
8359b42c1370/sist-iso-4026-2000
registers of currently valid International Standards.

ISO 225:1983, Fasteners - Belts, screws, studs and nuts - Symbols and designations of dimensions.

ISO 26’1: 1973, ISO general purpose metric screw threads - General plan.

ISO 888: 1976, Bolts, screws and studs - Nominal lengths, and thread lengths for general purpose bolts.

ISO 898-5: 1980, Mechanical properties of fasteners - Part 5: Set screws and similar threaded fasteners not un-
der tensile Stresses.

ISO 965-2: ‘l980, ISO general purpose metric screw threads - Tolerantes - Part 2: Limits of sizes for general
purpose bolt and nut threads - Medium quality.

ISO 965-3: 1980, ISO general purpose metric screw threads - Tolerantes - Part 3: Devia tions for constructional
threads.

ISO 3269: 1988, Fasteners - Acceptance inspection.

ISO 3506: 1979, Corrosion-resistant stainless steel fasteners - Specifications.

ISO 4042: 1989, Threaded components - Electroplated coatings.

ISO 4759-111978, Tolerantes for fasteners - Part 1: Bolts, screws and nuts with thread diameters between 1,6
(inclusive) and 150 mm (inclusive) and product grades A, B and C.

ISO 6157-1 :1988, Fasteners - Surface discontinuities - Part 1: Bolts, screws and studs for general
requirements.
 SIST ISO 4026:1996

ISO 4026:1993(E) 0 ISO

ISO 6157-3: 1988, Fasteners - Surface discon tinuities - Part 3: Belts, screws and studs for speciai
requiremen ts.

ISO 8839: 1986, Mechanical propeflies of fasteners - BoltsA, screwsJ studs and nuts made of non-ferrous
me tals.

ISO 8992: ‘1986, Fasteners - General requirements for bolts, screws, studs and nuts.

3 Dimensions
See figure 1 and table 1.

NOTE 1 Symbols and designations of dimensions are specified in ISO 225.

iV -i-yiTeh STANDARD PREVIEW Permissibie alternative form of sscket

i 1

(standards.iteh.ai)
A slight rounding or
NOTE - ßor broached sockets which are at the maximum
Limit of size, the overcut resulting from drilling
countersink at the mouth shall not exceed 20 % of the 1ength of any ftat of
of the socket
SISTisISO
permissible
4026:2000 the sockef.
https://standards.iteh.ai/catalog/standards/sist/df34b863-9319-464a-9bbd-
11 The 120” angle is a requirement for short-length screws of nominal length d,
situated above the dotted stepped Line in table 1.
8359b42c1370/sist-iso-4026-2000

2) The 4%” angLe applies only to the Portion of the Point situated below the
root diameter of the thread.

3) IncompLete thread u G 2 P.

Figure 1
 SIST ISO 4026:1996

ISO 4026:1993(E)

Tabie 4
Dimensions in millimetres

z Minor thread diameter

e min. 2) 0,803 1,003 1,427 1,73 23 2,87 3,44 4,58 5,72 6,86 $15 11,43 13,72
nom. 0,7 0,9 1,3 1,5 2 2,5 3 4 5 6 8 IO 12

4) 0,7 0,8 1,2 1,2 1,5 2 2 3 4 4,8 6,4 8 IO

t min.
5) 1,5 i,7 2 2 2,5 3 3,5 5 6 8 IO 12 15
1
l nom. I min. I max.
Approximate mass, in kilograms per 1 000 pieces (Q = 7,85 kg/dm3) (for information only)

iTeh STANDARD PREVIEW

(standards.iteh.ai)
SIST ISO 4026:2000
12 11,65 12,35https://standards.iteh.ai/catalog/standards/sist/df34b863-9319-464a-9bbd-
16 15,65 16,35 8359b42c1370/sist-iso-4026-2000
0,62 1,18 1,76 2,51 4,41 6,78 ‘-$;y 16,3 24,1 30
I
+-rm-----
20 19,58 20,42 1,49 2,24 3,21 5,67 8,76 12,4 Zl,5 32,3; 42
IL-----r
25 24,58 25,42 2,84 4,09 7,25 11,2 15,9 28 42,6 57
30 29,58 30,42 4,97 8,82 13,7 19,4 34,6 52,9 72
35 34,5 35,5 IO,4 16,2 22,9 41,l 63,2 87
40 39,5 40,5 12 18,7 26,4 47,7 73,5 102
45 44,5 45,5 Zl,2 29,9 54,2 83,8 117
50 49,5 50,5 23,7 33,4 60,7 94,1 132
55 54,4 55,6 36,8 67,3 104 147
60 I 594 1 w3 1 I I I I I 1 I 1 40,3 1 73,7 1 115 162

I NOTE - Commercial lengths are those between the stepped, continuous, bold lines. I

1) P = pitch of the thread

2) emin= 1,14 Smin,except for sizes M1,6, M2 and M2,5
3) s shall be gauged by attribute methods, see annex A for gauges.
4) For screws with nominal lengths above the dotted stepped line.
5) For screws with nominal lengths below the dotted stepped line.

3
 SIST ISO 4026:1996

PS0 4026:1993(E) Q ISO

4 Specifications and reference International Standards

See table 2.

Table 2

Threadl

Mechanical properties

Black Oxide (ther-

mal or Chemical)

Requirements for electroplating are given in ISO 4042.

Finish If different electroplating requirements are desired or if re-

quirements are needed for other finishes, they should be
iTeh STANDARD PREVIEW negotiated between customer and supplier.

Limits for surface discontinuities are given in ISO 61574

(standards.iteh.ai)
and ISO 6157-3.
Acceptability For acceptance procedure, see ISO 3269.
SIST ISO 4026:2000
https://standards.iteh.ai/catalog/standards/sist/df34b863-9319-464a-9bbd-
8359b42c1370/sist-iso-4026-2000

5 Designation
Example of designation: A hexagon socket set screw with flat point, thread M6, nominal length 2 = 12 mm and
of property class 45H is designated as follows:

Hexagon socket set screw ISO 4026 - M6 x 12 - 45H

4
 SIST ISO 4026:1996

ISO 4026:1993(E)

Annex A
(normative)

Gauging of hexagon socket

A.l Gauge dimensions

See Figure A.1 and table A.1.

mber

iTeh STANDARD PREVIEW

(standards.iteh.ai)
Truncatehex
k withSIST
size ISO
Amin4026:2000 rk with size Xm,x
to dimension
https://standards.iteh.ai/catalog/standards/sist/df34b863-9319-464a-9bbd-
8359b42c1370/sist-iso-4026-2000
Truncate hexagon
to dimension

GO member NOT GOmember

5” chamfer optional Optional construction Construction
for small sizes for small sizes

Figure A.l