Scribd
Upload
67 views8 pages

RAM Connectionreport

This document provides information on the design of a steel base connection for an 8.8 m lighting pole. It includes details on the members, connector, demands, geometric considerations, and design checks. The connection uses a 400x400x20 mm base plate welded to a 185x4 mm CHS column with a 700x700x1400 mm concrete pedestal. Design checks are performed for flexural yielding of the base plate and column weld capacity under axial and shear demands from the fixed biaxial connection. All capacity/demand ratios are below limits specified in the referenced design codes.

Uploaded by

ahmed fathi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
67 views8 pages

RAM Connectionreport

This document provides information on the design of a steel base connection for an 8.8 m lighting pole. It includes details on the members, connector, demands, geometric considerations, and design checks. The connection uses a 400x400x20 mm base plate welded to a 185x4 mm CHS column with a 700x700x1400 mm concrete pedestal. Design checks are performed for flexural yielding of the base plate and column weld capacity under axial and shear demands from the fixed biaxial connection. All capacity/demand ratios are below limits specified in the referenced design codes.

Uploaded by

ahmed fathi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

Pole 8.

8 m

Current Date: 8/25/2019 3:33 PM


Units system: SI
File name: D:\Yuksel\BRT-PH3\Babten-Lighting pole\Babten\Ram\BASE-8.8 m.cnx\

Steel connections
Data
__________________________________________________________________________________________________________________________

__________________________________________________________________________________

Connection name : Fixed biaxial BP


Connection ID : 3
__________________________________________________________________________________

Family: Column - Base (CB)


Type: Base plate
Description: Base-plate-8.8 m

GENERAL INFORMATION
Connector

MEMBERS
Column
Column type : Prismatic member
Section : CHS-185 x 4 mm
Material : S355
Longitudinal offset : 0 mm
Transversal offset : 0 mm

CONNECTOR
Base plate
Position on the support : Center
N: Longitudinal dimension : 400 mm
B: Transversal dimension : 400 mm
Thickness : 20 mm
Material : S 235
Column weld : E70XX
D: Column weld size (1/16 in) : 4
Override A2/A1 ratio : No
Include shear lug : No
Support
With pedestal : Yes
Longitudinal dimension (pedestal) : 700 mm
Transversal dimension (pedestal) : 700 mm
Thickness : 1400 mm
Material : C25
Include grouting : No
Anchor
Anchor position : Longitudinal position
Rows number per side : 1
Anchors per row : 2
Longitudinal edge distance on the plate : 50 mm

Page1
Transverse edge distance on the plate : 50 mm
Anchor type : J-bolt
Include lock nut : Yes
Anchor : M-24
Effective embedment depth : 621.72 mm
Total length : 695 mm
Material : S 235
Fy : 0.235 kN/mm2
Fu : 0.36 kN/mm2
Cracked concrete : Yes
Brittle steel : Yes
Anchors welded to base plate : No
Anchor reinforcement
Type of reinforcement : Primary
Tension reinforcement : No
Shear reinforcement : No

Page2
Current Date: 8/25/2019 3:34 PM
Units system: SI
File name: D:\Yuksel\BRT-PH3\Babten-Lighting pole\Babten\Ram\BASE-8.8 m.cnx\

Steel connections
Results
__________________________________________________________________________________________________________________________

__________________________________________________________________________________

Connection name : Fixed biaxial BP


Connection ID : 3
__________________________________________________________________________________

Family: Column - Base (CB)


Type: Base plate
Description: Base-plate-8.8 m
Design code: AISC 360-10 LRFD, ACI 318-08

DEMANDS
Description Pu Mu22 Mu33 Vu2 Vu3 Load type
[KN] [KN*m] [KN*m] [KN] [KN]
------------------------------------------------------------------------------------------------------------------
Comb -2.29 0.00 -10.05 1.81 0.00 Design
------------------------------------------------------------------------------------------------------------------

Design for major axis


Base plate (AISC 360-10 LRFD)
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References

Base plate
Distance from anchor to edge [mm] 38.00 6.35 --
Weld size [1/16in] 4 2 -- table J2.4

DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

Pedestal
Axial bearing [KN/mm2] 0.02 0.00 Comb 0.05 DG1 3.1.1;
Base plate
Flexural yielding (bearing interface) [KN*m/m] 21.15 7.47 Comb 0.35 DG1 Eq. 3.3.13,
DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 21.15 9.28 Comb 0.44 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1462.77 121.14 Comb 0.08 p. 8-9,
Sec. J2.5,
Sec. J2.4,
HSS Manual p. 7-10
Elastic method weld shear capacity [KN/m] 975.18 6.23 Comb 0.01 p. 8-9,
Sec. J2.5,
Sec. J2.4
Elastic method weld axial capacity [KN/m] 1462.77 373.88 Comb 0.26 p. 8-9,
Sec. J2.5,
Sec. J2.4

Ratio 0.44

Page1
Design for minor axis
Base plate (AISC 360-10 LRFD)
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References

Base plate
Distance from anchor to edge [mm] 38.00 6.35 --
Weld size [1/16in] 4 2 -- table J2.4

DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

Pedestal
Axial bearing [KN/mm2] 0.02 0.00 Comb 0.05 DG1 3.1.1;
Base plate
Flexural yielding (bearing interface) [KN*m/m] 21.15 0.11 Comb 0.01 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 21.15 9.28 Comb 0.44 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1462.77 121.14 Comb 0.08 p. 8-9,
Sec. J2.5,
Sec. J2.4,
HSS Manual p. 7-10
Elastic method weld shear capacity [KN/m] 975.18 0.00 Comb 0.00 p. 8-9,
Sec. J2.5,
Sec. J2.4
Elastic method weld axial capacity [KN/m] 1462.77 0.00 Comb 0.00 p. 8-9,
Sec. J2.5,
Sec. J2.4

Ratio 0.44

Major axis
Anchors
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References

Anchors
Anchor spacing [mm] 300.00 96.00 -- Sec. D.8.1
Concrete cover [mm] 188.00 50.80 -- Sec. 7.7.1
Effective length [mm] 645.72 -- 1376.00

DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

Anchor tension [KN] 80.33 15.39 Comb 0.19 Eq. D-3


Breakout of anchor in tension [KN] 85.96 15.39 Comb 0.18 Eq. D-4,
Sec. D.4.1.1
Breakout of group of anchors in tension [KN] 85.96 30.77 Comb 0.36 Eq. D-5,
Sec. D.4.1.1
Pullout of anchor in tension [KN] 40.82 15.39 Comb 0.38 Sec. D.4.1.1
Anchor shear [KN] 44.49 0.45 Comb 0.01 Eq. D-20
Breakout of anchor in shear [KN] 32.04 0.45 Comb 0.01 Sec. D.4.1.1
Breakout of group of anchors in shear [KN] 61.48 1.81 Comb 0.03 Sec. D.4.1.1
Pryout of anchor in shear [KN] 171.91 0.45 Comb 0.00 Eq. D-4,
Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 171.91 0.91 Comb 0.01 Eq. D-5,
Sec. D.4.1.1
Interaction of tensile and shear forces [KN] 0.00 0.00 Comb 0.00 Eq. D-3,
Eq. D-4,
Sec. D.4.1.1,
Eq. D-5,
Eq. D-20,
Sec. D.7

Page2
Ratio 0.38

Minor axis
Anchors
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References

Anchors
Anchor spacing [mm] 300.00 96.00 -- Sec. D.8.1
Concrete cover [mm] 188.00 50.80 -- Sec. 7.7.1
Effective length [mm] 645.72 -- 1376.00

DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

Anchor tension [KN] 80.33 15.39 Comb 0.19 Eq. D-3


Breakout of anchor in tension [KN] 85.96 15.39 Comb 0.18 Eq. D-4,
Sec. D.4.1.1
Breakout of group of anchors in tension [KN] 85.96 30.77 Comb 0.36 Eq. D-5,
Sec. D.4.1.1
Pullout of anchor in tension [KN] 40.82 15.39 Comb 0.38 Sec. D.4.1.1
Anchor shear [KN] 44.49 0.00 Comb 0.00 Eq. D-20
Breakout of anchor in shear [KN] 32.04 0.00 Comb 0.00 Sec. D.4.1.1
Pryout of anchor in shear [KN] 171.91 0.00 Comb 0.00 Eq. D-4,
Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 171.91 0.00 Comb 0.00 Eq. D-5,
Sec. D.4.1.1

Ratio 0.38

Global critical strength ratio 0.44

Biaxial
Maximum compression and tension (Comb)

------------------------------------------------------------------------------------
Maximum bearing pressure 1.16 [N/mm2]
Minimum bearing pressure 1.16 [N/mm2]
Maximum anchor tension 15.39 [KN]
Minimum anchor tension 0.00 [KN]
Neutral axis angle 0.00
Bearing length 71.25 [mm]

Page3
------------------------------------------------------------------------------------

Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[mm] [mm] [KN] [KN]
----------------------------------------------------------------------------------------------
1 -150.00 -150.00 0.45 15.39
2 -150.00 150.00 0.45 0.00
3 150.00 150.00 0.45 0.00
4 150.00 -150.00 0.45 15.39
----------------------------------------------------------------------------------------------

Major axis
Results for tensile breakout (Comb)

Group Area Tension Anchors


[mm2] [KN]
----------------------------------------------------------------------
1 490000.00 30.77 1, 4
----------------------------------------------------------------------

Results for shear breakout (Comb)

Group Area Shear Anchors


[mm2] [KN]
--------------------------------------------------------------------
1 525000.00 1.81 1, 2, 3, 4
2 210000.00 0.91 2, 3
--------------------------------------------------------------------

Page4
Minor axis
Results for tensile breakout (Comb)

Group Area Tension Anchors


[mm2] [KN]
----------------------------------------------------------------------
1 490000.00 30.77 1, 4
----------------------------------------------------------------------

Page5

You might also like