0% found this document useful (0 votes)
53 views2 pages

Cp12170e X

This document provides specifications for a lead-acid battery. It is a 12V 17Ah sealed lead-acid battery that uses absorbed glass mat technology. The battery uses lead dioxide for the positive plate and lead for the negative plate with dilute sulfuric acid electrolyte. It has safety features like valves that allow gases to escape if overcharged to avoid pressure buildup. The document details the battery's construction, general features, performance characteristics, dimensions, and discharge and charge characteristics.

Uploaded by

DAVID RUIZ
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
53 views2 pages

Cp12170e X

This document provides specifications for a lead-acid battery. It is a 12V 17Ah sealed lead-acid battery that uses absorbed glass mat technology. The battery uses lead dioxide for the positive plate and lead for the negative plate with dilute sulfuric acid electrolyte. It has safety features like valves that allow gases to escape if overcharged to avoid pressure buildup. The document details the battery's construction, general features, performance characteristics, dimensions, and discharge and charge characteristics.

Uploaded by

DAVID RUIZ
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

CP12170E-X 12V 17Ah(20hr)

The rechargeable batteries are lead-lead dioxide systems. The dilute sulfuric acid electrolyte
is absorbed by separators and plates and thus immobilized. Should the battery be
accidentally overcharged producing hydrogen and oxygen, special one-way valves allow the
gases to escape thus avoiding excessive pressure build-up. Otherwise, the battery is
completely sealed and is, therefore, maintenance-free, leak proof and usable in any position.

Battery Construction
Component Positive plate Negative plate Container Cover Safety valve Terminal Separator Electrolyte
Raw material Lead dioxide Lead ABS ABS Rubber Copper Fiberglass Sulfuric acid

General Features Performance Characteristics


● Absorbent Glass Mat (AGM) technology Nominal Voltage 12V
for efficient gas recombination of up to Number of cell 6
99% and freedom from electrolyte
Design Life 5 years
maintenance or water adding.
● Not restricted for air transport-complies Nominal Capacity 77oF(25oC)
with IATA/ICAO Special Provision A67. 20 hour rate (0.85A, 10.5V) 17Ah
● UL-recognized component. 10 hour rate (1.68A, 10.5V) 16.8Ah
● Can be mounted in any orientation. 5 hour rate (3.09A, 10.5V) 15.45Ah
● Computer designed lead, calcium tin alloy 1 hour rate (11.8A, 9.6V) 11.8Ah
grid for high power density. Internal Resistance
● Long service life, float or cyclic Fully Charged battery 77oF(25oC) 16.5mOhms
applications. Self-Discharge
● Maintenance-free operation. 3% of capacity declined per month at 20oC(average)
● Low self discharge.
Operating Temperature Range
Discharge -20~60oC
Dimensions and Weight Charge -10~60oC
Storage -20~60oC
Length(mm / inch) 181 / 7.13 o o
Max. Discharge Current 77 F(25 C) 255A(5s)
Width(mm / inch) 77 / 3.03
Height(mm / inch) 167 / 6.57 Short Circuit Current 850A
Total Height(mm / inch) 167 / 6.57 Charge Methods: Constant Voltage Charge 77oF(25oC)
Approx. Weight(Kg / lbs) 5.3 / 11.7 Cycle use 2.30-2.35VPC
Maximum charging current 6.8A
Temperature compensation -30mV/oC
Standby use 2.23-2.27VPC
Temperature compensation -20mV/oC

Discharge Constant Current (Amperes at 77oF25oC)


End Point
5min 10min 15min 30min 1h 3h 5h 10h 20h
Volts/Cell
1.60V 64.9 44.1 34 19.8 11.8 4.57 3.09 1.78 0.89
1.65V 62.8 43 33.3 19.4 11.6 4.5 3.03 1.75 0.88
1.70V 60.5 41.9 32.6 18.9 11.4 4.42 2.97 1.72 0.87
1.75V 58 40.7 31.8 18.4 11.2 4.35 2.91 1.68 0.85
1.80V 55.3 39.4 30.9 17.9 10.9 4.27 2.84 1.65 0.84

Discharge Constant Power (Watts at 77oF25oC)


End Point
5min 10min 15min 30min 45min 1h 2h 3h 5h
Volts/Cell
1.60V 111 78.6 61.3 35.3 27.4 22.4 13.0 9.09 6.13
1.65V 107 77.2 60.2 34.8 27.1 22.2 12.9 9.01 6.07
1.70V 103 75.8 59.0 34.3 26.8 22.0 12.8 8.92 6.01
1.75V 98.0 74.3 57.8 33.7 26.4 21.7 12.7 8.83 5.95
1.80V 94.0 72.8 56.5 33.1 26.0 21.5 12.5 8.74 5.88
(Note)The above characteristics data are average values obtained within
three charge/discharge cycles not the mimimum values.

page1 of 2 www.vision-batt.com
CP12170E-X 12V17Ah

Charged
O
Discharge characteristic (25 C)

Current

Voltage
Volume
Constant voltage charging
o
characteristic (0.25CA,25 C)
13.0
(%) (XCA) (V)
140
12.0
120 0.25
15.0 Charged Volume
Voltage(v)

11.0
100 0.20
10.0
9 14.0 Charge Voltage
35 80
0.15
.18 13.0
9.0 60
0.10
40 12.0
8.0
20 0.05
11.0 Charging Current
0
0 1 2 3 5 10 20 30 60 2 3 5 10 20 30 0 0
min h 0 2 4 6 8 10 12 14 16 18 20
Discharge time Charging time (hours)

Relationship between
Self-discharge characteristic
charging voltage and temperature
110

100
15.6
90

Capacity(%)
C y c le
Voltage(V)

15.0 Use
80
14.4
70
S ta n d
13.8 by Use
60 o o o
C C C
13.2 50

40
-10 0 10 20 30 40 50 60 0 2 4 6 8 10 12 14 16 18 20
Ambient temperature( oC) Storage time: months

Cycle service life in relation to


Life characteristics of Standby use
120 depth of discharge
120

100
100
Capacity(%)

80
Capacity(%)

80

60 60
Testing conditions:floating voltage:2.27 to 2.30V Cell 100% D.O.D. 50% D.O.D. 30% Depth of discharge
ambient temperature: 25 oC(77 oF)
40 40

20 20

0 200 400 600 800 1000 1200 1400


0 1 2 3
Life(year) Number of cycles(cycles)

Temperature effects on float life Temperature effects on capacity


10
120

100
C
0 .0 5
Life(years)

0 .1 C
Capacity (%)

80
2.30V Cell 0 . 2 C
1
60
1 .0 C
40 2 .0 C
3 .0 C
20

0.1 0
10 20 30 40 50 60
-20 -10 0 10 20 30 40 50( o C)
Temperature( oC)

THE INTERNATIONAL CERTIFICATION NETWORK

MH25860 G4M19906-9202-E-16
ISO9001:2000

Shenzhen Center Power Tech. Co., Ltd. www.vision-batt.com


Center Power Industrial Park, Tongfu Industrial District Dapeng Town, 518120 Shenzhen, China
Tel: (+86-755) 8431 8088 Fax: (+86-755) 8431 8038 E-mail: [email protected]

Copy Right Shenzhen Center Power Technology Co., Ltd (Edition 2011-8)

Page 2 of 2

You might also like