Energy Conservation Building Code

User Guide

ENERGY CONSERVATION BUILDING CODE (ECBC) USER GUIDE

July 2009

Energy Conservation Building Code User Guide

2009 Bureau of Energy Eficiency

Published by: Bureau of Energy Eficiency 4th Floor, Sewa Bhawan, R. K.Puram, New Delhi, India Developed by: USAID ECO-III Project International Resources Group 2, Balbir Saxena Marg, Hauz Khas, New Delhi, India

No portion (graphics or text) of this report may be reproduced, translated, or transmitted in any form or manner by any meansincluding but not limited to electronic copy, photocopy, or any other informational storage and retrieval system without explicit written consent from Bureau of Energy Eficiency, New Delhi.

All rights reserved Printed in New Delhi, India ISBN No. 978-81-909025-3-3 July 2009

This report is made possible by the generous support of the U.S. Government through the ECO-III Project to the Indian Government. The views expressed in this report do not necessarily relect the views of partner countries United States of America and India or the United States Agency for International Development.

USAID ECO-III Project

The Energy Conservation and Commercialization (ECO) Program was signed between the Government of India (GOI) and USAID in January 2000 under a bilateral agreement with the objective to enhance commercial viability and performance of Indian energy sector and to promote utilization of clean and energy-eficient technologies in the sector. Following the enactment of the Energy Conservation Act 2001, ECO-I Project supported GOI in the establishment of the Bureau of Energy Eficiency (BEE). Support to BEE was provided to set up procedures and authorities, establish ofice facilities and assist in several activities leading to the development of BEEs Action Plan including thrust area such as the development of an energy auditor certiication program. ECO-II Project provided BEE with necessary technical assistance and training support to implement three thrust areas of the Action Plan. The irst area was to develop the Energy Conservation Building Codes (ECBC) for the ive climatic zones of India, the second was to support Maharashtra Energy Development Agency in developing strategies for energy conservation and implementation of selected programs, and the third area focused on implementing a pilot DSM program to replace incandescent lamps with CFLs in the state of Karnataka in partnership with BESCOM. Since November 2006, International Resources Group (IRG), with support from its partners IRG Systems South Asia, Alliance to Save Energy and DSCL Energy Services, other partner organizations and consultants has been implementing the ECO-III Project by working closely with BEE, Gujarat Energy Development Agency, and Punjab Energy Development Agency. ECBC User Guide has been produced to assist Government of India in the implementation of ECBC, which was launched by Ministry of Power in May 2007. It is hoped that this document will help in creating awareness and enhancing understanding about the ECBC. ECO-III Project has developed Tip Sheets and Design Guides in the past to help in the ECBC implementation efforts. More information as well as electronic copies of all the publications can be accessed at www.eco3.org.

Foreword
The Energy Conservation Act, 2001(52 of 2001) empowers the Central Government under Section 14(p) read with Section 56(2)(l) to prescribe Energy Conservation Building Code (ECBC). The Code deines norms and standards for the energy performance of buildings and their components based on the climate zone in which they are located. Under the leadership of Bureau of Energy Eficiency (BEE), a Committee of Experts inalized ECBC in consultation with various Stakeholders in 2007, with an overall purpose to provide minimum requirements for the energy-eficient design and construction of buildings. ECBC covers building envelope, heating, ventilation, and air conditioning system, interior and exterior lighting system, service hot water, electrical power system and motors. In May 2007, the Ministry of Power, Government of India formally launched the ECBC for its voluntary adoption in the country. Since then, BEE has been promoting and facilitating its adoption through several training and capacity building programmes. BEE is also monitoring implementation of ECBC through the ECBC Programme Committee (EPC). EPC also reviews periodically the inconsistencies and comments on ECBC received from various quarters. In this context, BEE in consultation with EPC and support from USAID ECO-III Project brought out a revised version of ECBC in May 2008. During the capacity building effort, a need was clearly felt to provide additional guidance to design and construction professionals on the rationale behind the ECBC speciications and provide explanations to the key terms and concepts governing these speciications so that people are able to comprehend ECBC in a better way. Considering this growing need for developing a better understanding of ECBC in the country, the ECBC User Guide has been prepared under the USAID ECO-III Project in close partnership with BEE. The document aims to guide and assist the building designers, architects and all others involved in the building construction industry to implement ECBC in real situations. The document is written both as a reference and as an instructional guide. It also features examples, best practices, checklists, etc. to direct and facilitate the design and construction of ECBC-compliant buildings in India. I am happy to note that the ECBC User Guide Development Team has made a concerted effort to provide all the information, especially minimum performance standards that buildings need to comply with, in one place. Consequently, it is my hope that users of ECBC trying to show compliance through the prescriptive path will ind it easier to do so through the guidance provided in the document. The ECBC User Guide also provides additional guidance on the Whole Building Performance method by making references to international publications that are widely used by the building design community. I thank the entire ECBC User Guide Development Team, led by Dr. Satish Kumar, for its extensive efforts in bringing out this document. I would like to express my sincere appreciation to the USAID for providing this technical assistance under the ECO-III Project and to the International Resources Group for spearheading this team effort.

17th July, 2009

(Dr. Ajay Mathur)

ECBC User Guide Development Team

Satish Kumar, Team Leader IRG, USAID ECO-III Project Aleisha Khan, Alliance to Save Energy Anurag Bajpai, IRG, USAID ECO-III Project G. S. Rao, Team Catalyst Jyotirmay Mathur, Malviya National Institute Technology Laurie Chamberlain, International Resources Group (IRG) P. C. Thomas, Team Catalyst Rajan Rawal, Center for Environmental Planning and Technology Ravi Kapoor, IRG, USAID ECO-III Project Surekha Tetali, International Institute of Information Technology Vasudha Lathey Vishal Garg, International Institute of Information Technology

Acknowledgements
Energy Conservation Building Code (ECBC) User Guide, developed by the USAID ECO-III Project in association with Bureau of Energy Eficiency (BEE) aims to support the implementation of ECBC. I would like to thank Dr. Archana Walia, Project Manager, and Mr. S. Padmanaban of USAID for their constant encouragement and steadfast support during the development process. I would like to acknowledge the tremendous support and encouragement provided by Dr. Ajay Mathur, Director General, and Mr. Sanjay Seth, Energy Economist of BEE in the preparation of the Guide. A substantial undertaking of this nature would not have been possible without the extremely valuable technical contribution provided by the Development Team of ECBC User Guide especially Ms. Vasudha Lathey, Ms. Aleisha Khan of Alliance to Save Energy (ASE), Dr. Vishal Garg and Ms. Surekha Tetali of International Institute of Information Technology (IIIT), Prof. Rajan Rawal of Center for Environmental Planning and Technology (CEPT), Dr. Jyotirmay Mathur of Malviya National Institute Technology (MNIT), Mr. P. C. Thomas and Mr. G. S. Rao of Team Catalyst. I would like to acknowledge the assistance that the Development Team received from the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) Inc., USA. The 90.1 User Manual, ANSI/ ASHRAE/IESNA Standard 90.1-2004, provided us with a robust framework and a sound technical reference during the development of the ECBC User Guide. I am also thankful to Ms. Meredydd Evans of Paciic NorthWest National Laboratory (PNNL), and to Saint Gobain, DuPont, ASAHI-India, and Dr. Mahabir Bhandari (DesignBuilder) for providing inputs on many iterations of this document. I would like to convey my special thanks to the ECO-III Project Team Mr. Ravi Kapoor for his substantial technical contribution to the development of the entire document, Mr. Anurag Bajpai for his tireless efforts in coordinating inputs from the Development Team members, and Ms. Meetu Sharma for her persistence efforts to prepare the graphics and desktop layout of multiple iterations of the document. Without the perseverance and discipline of ECO-III Project Team this work would not have been possible. I also like to thank Ms. Laurie Chamberlain of International Resources Group (IRG) HQ for assisting us in carrying out technical editing of this document.

17th July, 2009

(Dr. Satish Kumar) Chief of Party, USAID ECO-III Project International Resources Group

How to Use This Guide

The ECBC User Guide follows the same structure as the Energy Conservation Building Code. Consequently, Chapters 1 through 8 and Appendix A through G are identical to the ECBC chapters and the sections within each chapter also follow the ECBC. Appendix B provides detailed guidance on the Whole Building Performance method. Assumptions that can be standardized have been included to reduce the chances of gamesmanship and to create a framework that would allow for apples to apples comparison across different projects while creating simulation models for Standard and Proposed Design. Appendix E is about Climate Zones in India. This appendix provides a summary of each of the ive climate zones and another table that provides a listing of major Indian cities along with its climatic zone. A new Appendix H has been included that provides a comparison of International Building Energy Standards. Apart from comparing some of the technical speciications, this appendix also provides the different approaches taken by countries to check code compliance and enforcement. It is hoped that this section will provide some ideas to the policy makers on how to make ECBC compliance mandatory so that minimum energy eficiency performance can be met by buildings coming under the scope of ECBC. The ECBC User Guide has been designed in an easy to understand format. The document uses a consistent format and provides guidance at the following three levels:

a) Text that is shown in Blue

This text is a direct excerpt from the ECBC document and is likely to serve as an anchor for many of the guidance text and examples included in different chapters. Users interested in showing ECBC compliance should pay close attention to the text drawn from ECBC and shown in blue. Examples of ECBC text and ECBC table are reproduced below for guidance: The Code is applicable to buildings or building complexes that have a connected load of 500 kW or greater or a contract demand of 600 kVA or greater. Window Wall Ratio
0 - 0.3 0.31-0.4

Minimum VLT
0.27 0.20

b) Boxed Text showing Tips, Frequently Asked Questions (FAQ), Examples, etc.
The Boxed Text provides guidance to the users for better understanding of ECBC concepts and ECBC applicability in different situations. An example of Boxed Text is shown below:

Box 1-A: : Role of Climate Zone

The ECBC building envelope requirements are based on the climate zone in which the building is located. ECBC deines ive climate zones (hot-dry; warm-humid; composite; temperate; cold), which are distinctly unique in their weather proiles (Appendix E). Based on the characteristics of climate, the thermal comfort requirements in buildings and their physical manifestation in architectural form are also different for each climate zone

c) Normal text in black

This type of text forms the core of the ECBC User Guide and provides overall guidance on how best to understand and apply ECBC.

Table of Contents
USAID ECO-III Project Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v . . . . . . . . . . vii . . viii . . ix . . x ECBC User Guide Development Team . Acknowledgements . 1. 2. How to Use This Guide . . . . .

. . . .

Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1 2.2 2.3 2.4 Applicable Building Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Exemptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety, Health, And Environmental Codes Take Precedence. . . . . . . . . . . . . . . . 2 Reference Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Compliance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.1.1 Mandatory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.1.2 New Buildings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.1.3 Additions to Existing Buildings . . . . . . . . . . . . . . . . . . . . . . . . 4 3.1.4 Alterations to Existing Buildings . . . . . . . . . . . . . . . . . . . . . . . 5 3.2 3.3 3.4 Compliance Approaches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Administrative Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Compliance Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.4.2 Supplemental Information . . . . . . . . . . . . . . . . . . . . . . . . 11

3.

Administration and Enforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.1

4.

Building Envelope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.1 4.2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Mandatory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.2.1 Fenestration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.2.2 Opaque Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.2.3 Building Envelope Sealing . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.3 Prescriptive Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.3.1 Roofs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.3.2 Cool Roofs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4.3.3 Opaque Walls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.3.4 Vertical Fenestration . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.3.5 Skylights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.4 Building Envelope Trade-Off Option . . . . . . . . . . . . . . . . . . . . . . . 32

5.

Heating, Ventilation and Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 33

5.1 5.2

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Mandatory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.2.1 Natural Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.2.2 Minimum Equipment Eficiencies . . . . . . . . . . . . . . . . . . . . . 38 5.2.3 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 5.2.4 Piping and Ductwork . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 5.2.5 System Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 5.2.6 Condensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

5.3

Prescriptive Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 5.3.1 Economizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 5.3.2 Variable Flow Hydronic Systems . . . . . . . . . . . . . . . . . . . . . . 50

6.

Service Water Heating and Pumping . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.1 6.2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Mandatory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.2.1 Solar Water Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.2.2 Equipment Eficiency . . . . . . . . . . . . . . . . . . . . . . . . . . 54 6.2.3 Supplementary Water Heating System . . . . . . . . . . . . . . . . . . . . 55 6.2.4 Piping Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 6.2.5 Heat Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 6.2.6 Swimming Pools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.2.7 Compliance Documentation . . . . . . . . . . . . . . . . . . . . . . . . 57

7.

Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 7.1 7.2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Mandatory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 7.2.1 Lighting Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 7.2.2 Exit Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 7.2.3 Exterior Building Grounds Lighting . . . . . . . . . . . . . . . . . . . . . 64 7.3 Prescriptive Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 7.3.1 Interior Lighting Power . . . . . . . . . . . . . . . . . . . . . . . . . . 65 7.3.2 Building Area Method . . . . . . . . . . . . . . . . . . . . . . . . . . 65 7.3.3 Space Function Method . . . . . . . . . . . . . . . . . . . . . . . . . . 66 7.3.4 Installed Interior Lighting Power . . . . . . . . . . . . . . . . . . . . . . 67 7.3.5 Exterior Lighting Power . . . . . . . . . . . . . . . . . . . . . . . . . . 68

8.

Electrical Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 8.1 8.2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Mandatory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 8.2.1 Transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 8.2.2 Energy-Eficient Motors . . . . . . . . . . . . . . . . . . . . . . . . . 72 8.2.3 Power Factor Correction . . . . . . . . . . . . . . . . . . . . . . . . . 77

8.2.4 Check-Metering and Monitoring . . . . . . . . . . . . . . . . . . . . . . 78 8.2.5 Power Distribution Systems . . . . . . . . . . . . . . . . . . . . . . . . 78 9. APPENDIX A: ECBC Deinitions, Abbreviations and Acronyms . . . . . . . . . . . . . . A.1 9.1 9.2 9.3 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1 Deinitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1 Abbreviations and Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . A.12

10. APPENDIX B: Whole Building Performance Method . . . . . . . . . . . . . . . . . . . B.1 10.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.1 10.1.1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.1 10.1.2 Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.2 10.1.3 Annual Energy Use . . . . . . . . . . . . . . . . . . . . . . . . . . . B.3 10.1.4 Trade-offs Limited to Building Permit . . . . . . . . . . . . . . . . . . . . B.3 10.1.5 Documentation Requirements . . . . . . . . . . . . . . . . . . . . . . . B.3 10.2 Simulation General Requirements . . . . . . . . . . . . . . . . . . . . . . . . . B.3 10.2.1 Energy Simulation Program . . . . . . . . . . . . . . . . . . . . . . . . B.3 10.2.2 Climate Data Requirements . . . . . . . . . . . . . . . . . . . . . . . . B.5 10.2.3 Compliance Calculations . . . . . . . . . . . . . . . . . . . . . . . . . B.5 10.3 Calculating the Energy Consumption of the Proposed Design and the Standard Design . . . . . B.6 10.3.1 The simulation model for calculating the Proposed Design and the Standard Design shall be developed in accordance with the requirements in Table 10.1 . . . . . . . . . . . B.6 11. APPENDIX C: Default Values for Typical Constructions . . . . . . . . . . . . . . . . . . C.1 11.1 Procedure for Determining Fenestration Product U-Factor and Solar Heat Gain Coeficient . . C.1 11.2 Default U-factors and Solar Heat Gain Coeficients for Unrated Fenestration Products . . . . C.2 11.2.1 Unrated Vertical Fenestration . . . . . . . . . . . . . . . . . . . . . . . C.2 11.2.2 Unrated Sloped Glazing and Skylights . . . . . . . . . . . . . . . . . . . . C.2 11.3 Typical Roof Constructions . . . . . . . . . . . . . . . . . . . . . . . . . . . C.2 11.4 Typical Wall Constructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . C.3 12. APPENDIX D: Building Envelope Tradeoff Method . . . . . . . . . . . . . . . . . . . D.1 12.1 The Envelope Performance Factor . . . . . . . . . . . . . . . . . . . . . . . . D.1 12.1.1 The envelope performance factor shall be calculated using the following equations. . . D.1 12.1.2 Overhang and Side Fin Coeficients . . . . . . . . . . . . . . . . . . . . . D.2 12.1.3 Baseline Building Deinition . . . . . . . . . . . . . . . . . . . . . . . . D.5 13. APPENDIX E: Climate Zone Map of India . . . . . . . . . . . . . . . . . . . . . . . E.1 13.1 Climate Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.1 14. APPENDIX F: Air-Side Economizer Acceptance Procedures . . . . . . . . . . . . . . . . F.1 14.1 Construction Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . F.1 14.2 Equipment Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F.1 15. APPENDIX G: ECBC Compliance Forms . . . . . . . . . . . . . . . . . . . . . . . G.1 15.1 Envelope Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G.1

15.2 Building Permit Plans Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . G.2 15.3 Mechanical Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G.3 15.4 Mechanical Permit Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . G.4 15.5 Lighting Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G.5 15.6 Lighting Permit Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . G.6 15.7 Whole Building Performance Checklist . . . . . . . . . . . . . . . . . . . . . . . G.7 16. APPENDIX H: Comparison Of International Building Energy Standards . . . . . . . . . . . H.1 17. APPENDIX I: References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I.1

List of Tables
Table 4.1: Values of Surface Film Resistance Based on Direction of Heat Flow . Table 4.3: Comfort Requirements and Physical Manifestations in Buildings . . . . . . . . . . . . . . . . . . . . . . . 14 . . 15 . . 19 . . 21 . . 26 . . 26 Table 4.2: Thermal Resistances of Unventilated Air Layers Between Surfaces with High Emittance . Table 4.4: Roof Assembly U-Factor and Insulation R-value Requirements (ECBC Table 4.3.1) .

Table 4.5: Opaque Wall Assembly U-Factor and Insulation R-value Requirements (ECBC Table 4.2) . Table 4.6: Vertical Fenestration U-factor (W/m2K) and SHGC Requirements (ECBC Table 4.3) . .

Table 4.7: Defaults for Unrated Vertical Fenestration (Overall Assembly including Sash and Frame) - Table 11.1 of ECBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Table 4.8: SHGC M Factor Adjustments for Overhangs and Fins (ECBC Table 4.4) . . Table 4.9: Minimum VLT Requirements (ECBC Table 4.5) . . . . . . . . . . . . . . . . . . . Table 4.10: Skylight U-Factor and SHGC Requirements (ECBC Table 4.6) . . . Table 5.1: Optimum Size/Number of Fans for Rooms of Different Sizes . . . . . . . 28 . . . . . . . . . . . . . . . . . . 29 . . 31 . . 37 . . 42 . . 42

. . . .

Table 5.2: Chillers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Table 5.3: Power Consumption Ratings for Unitary Air Conditioners Under Test Conditions . Table 5.4: Power Consumption Ratings for Split Air Conditioners Under Test Conditions . . Table 5.5: Power Consumption Rating for Packaged air Conditioners-under test conditions Table 5.6: Insulation of Heating Systems . . Table 5.7: Insulation of Cooling Systems . . Table 5.8: Ductwork Insulation . . . . . . . . 42

. . . . . . . . . . . . . . . . . . . . . . . . 44 . . . . . . . . . . . . . . . . . . . . . . . . 44

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 . . . . . . . . . . . . . . . . 55

Table 5.9: Sample R-values for Duct Insulation Materials . . . . . . . . . . . . . . . . . . . . 45 Table 6.1: Standing Loss in Storage Type Electric Water Heaters . Table 6.2: Insulation of Hot Water Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Table 7.1: Interior Lighting Power- Building Area Method (ECBC Table 7.1) . . . . . . . . . . . . 66 Table 7.2: Interior Lighting Power- Space Function Method (ECBC Table 7.2) . . . . . . . . . . . . 66 Table 7.3: Exterior Lighting Building Power (ECBC Table 7.3) . . . . . . . . . . . . . . . . . . 68 Table 8.1: Dry-Type Transformers (ECBC Table 8.1) . . . . . . . . . . . . . . . . . . . . . . 71 Table 8.2: Oil Filled Transformers (ECBC Table 8.2) . . . . . . . . . . . . . . . . . . . . . . 71 Table 8.3: Values of Performance Characteristic of Two Pole Energy-Eficient Induction Motors. . . . . 73 Table 8.4: Values of Performance Characteristic of 4 Pole Energy-Eficient Induction Motors. . Table 8.5: Values of Performance Characteristic of 6 Pole Energy-Eficient Induction Motors. . Table 8.6: Values of Performance Characteristic of 8 Pole Energy-Eficient Induction Motors. . Table 10.2: Standard Fan Brake Horsepower . Table 10.3: Type and Number of Chillers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 . . 75 . . 75 . B.19

Table 10.1: Modeling Requirements for Calculating Proposed and Standard Design . . . . . . . . . . B.7 . . . . . . . . . . . . . . . . . . . . . . . B.19 . . . . . . . . . . . . . . . . . . . . . . . . . . . B.22 . B.22

Table 10.4: Part-Load Performance for VAV Fan Systems . . . . . . . . . . . . . . . . . . . B.20 Table 10.5: HVAC Systems Map (Reproduced from ECBC 10.2) . Table 10.6: Electrically Operated Packaged Terminal Air Conditioners .

Table 10.7: Building Energy Model Information. . . . . . . . . . . . . . . . . . . . . . . B.23 Table 11.1: Defaults for Unrated Vertical Fenestration (Overall Assembly including the Sash and Frame) . C.2 Table 11.2: Defaults for effective U-Factor for Exterior Insulation layers (under review) . . . . . . . . C.2 Table 11.3: Defaults for effective U-factor for Exterior Insulation Layers (under review) . . . . . . . . C.3 Table 12.1: Envelope Performance Factor Coeficients-Composite Climate (under review) . Table 12.3: Envelope Performance Factor Coeficients-Hot Humid Climate (under review) Table 12.4: Envelope Performance Factor Coeficients-Moderate Climate (under review) . Table 12.5: Envelope Performance Factor Coeficients-Cold Climate (under review) . . . . . . . . . . . . . . . . . . . . . D.1 . . D.2 . . D.2 . . D.2 Table 12.2: Envelope Performance Factor Coeficients-Hot Dry Climate (under review) . . . . . . . . D.2

Table 12.6: Overhang and Side Fin Coeficients . . . . . . . . . . . . . . . . . . . . . . . . D.3 Table 13.1: Classiications of Different Climate Zones in India . . . . . . . . . . . . . . . . . . E.2 Table 13.2: Climate Zone of the Major Indian Cities . . . . . . . . . . . . . . . . . . . . . . E.3

List of Figures
Figure 3.1: Design Process for the Whole Building Performance Method . . . . . . . . . . . . . . Figure 3.2: The Building Design and Construction Process . Figure 4.1: Building Envelope . . . . . . . . . . . . . Figure 4.2: The Solar and Blackbody Spectrum . . Figure 4.4: Typical Cavity Wall Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 9 . . 12

. . . . . . . . . . . . . . . . . . . . . . 13 . . . . . . . . . . . . . . . . . . . . . . 15

Figure 4.3: Schematic Showing Three Modes of Heat Transfer . . . . . . . . . . . . . . . . . . 13 Figure 4.5: Direct and Indirect Solar Radiation . . Figure 4.7: Building Roofs . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 4.6: Heat Transfer (Conduction, Convection, & Radiation) and Iniltration Across a Window . . . . 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 . . 28 . . 30 . . 31 . . 38 . . 49 . . 53 . . 54 . . 64 . . 64 . . 69 . . 70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 4.8: Typical Insulation Techniques for RCC Roof Construction. Figure 4.9: Heat Transfer Through Roof Figure 4.10: Projection Calculation . Figure 4.12: Skylight Installations . Figure 5.2: Economizer . . . . . . . . . . . . .

Figure 4.11: Illustration to show U-factor, SHGC, and VLT .

Figure 5.1: Acceptable operative temperature ranges for naturally conditioned spaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6.1: Batch Collector Passive System . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Figure 6.2: Active Indirect System . Figure 6.4: Heat Trap Elements . . . . . . . . . . Figure 6.3: Instantaneous Water Heater .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 . . . . . . . . . . . . . . . . . . . .

Figure 7.1: Relative Eficacy of Major Light Sources (Lumens/Watt) . Figure 7.2: Watts per Lighting System Eficiency . Figure 8.1: Transformer . . . . . . . . . . . . . . . Figure 8.2: Transformer loss vs % Load .

. . . .

Figure 8.3: Increase in eficiency (Percentage points) . . . . . . . . . . . . . . . . . . . . . . 76 Figure 8.4: Proile cutaway of an induction motor stator and rotor . . Figure 13.1: Climate Zone Map . . . . . . . . . . . . . . . . 77 . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.1

Purpose

1. Purpose
to provide The purpose of Energy Conservation Building Code (ECBC) is systems. minimum requirements for energy-eficient design and construction of buildings and their The building sector represents about 33% of electricity consumption in India, with commercial sector and residential sector accounting for 8%and 25% respectively. Estimates based on computer simulation models indicate that ECBC-compliant buildings can use 40 to 60% less energy than conventional buildings. It is estimated that the nationwide mandatory enforcement of the ECBC will yield annual savings of approximately 1.7 billion kWh. The ECBC is expected to overcome market barriers, which otherwise result in under-investment in building energy eficiency. The ECBC was developed as a irst step towards promoting energy eficiency in the building sector. The ECBC (also referred to as The Code in this document) is the result of extensive work by the Bureau of Energy Eficiency (BEE) and its Committee of Experts. It is written in code-enforceable language and addresses the views of the manufacturing, design, and construction communities as an appropriate set of minimum requirements for energy-eficient building design and construction. For developing the Code, building construction methods across the country were reviewed and various energyeficient design and construction practices were evaluated that could reduce energy consumption in building. In addition, detailed life-cycle cost analyses were conducted to ensure that the Code requirements relect costeffectiveness and practical eficiency measures across ive different climate zones in India. While taking into account different climate zones, the Code also addresses site orientation and speciies better design practices and technologies that can reduce energy consumption without sacriicing comfort and productivity of the occupants. The ECBC User Guide (also referred to as The Guide in this document) has been developed to provide detailed guidance to building owners, designers, engineers, builders, energy consultants, and others on how to comply with the Code. It provides expanded interpretation, examples, and supplementary information to assist in applying ECBC during the design and construction of new buildings as well as additions and alterations to existing buildings. This Guide can also be used as a document by authorities having jurisdiction in the enforcement of the Code once it is made mandatory. The Guide follows the nomenclature of the Code. It is written both as a reference and as an instructional guide, and can be helpful for anyone who is directly or indirectly involved in the design and construction of ECBC-compliant buildings.

Energy Conservation Building Code (ECBC) User Guide

Scope

2. Scope

he Code is applicable to buildings or building complexes that have a connected load of 500 kW or greater or a contract demand of 600 kVA or greater.

Generally, buildings or complexes having conditioned area of 1,000 m2 or more will fall under this category. The Code is presently under voluntary adoption in the country. This Code would become mandatory as and when it is notiied by the Central and State government in the oficial Gazette under clause (p) of 14 or clause (a) of 15 of the Energy Conservation Act 2001 (52 of 2001)

2.1 Applicable Building Systems

The provisions of the Code apply to: Building envelopes, except for unconditioned storage spaces or warehouses Mechanical systems and equipment, including heating, ventilating, and air conditioning, (HVAC) Service hot water heating Interior and exterior lighting Electrical power and motors Speciic compliance requirement of the above building components and systems are discussed in Chapter 4 through Chapter 8 of this Guide.

2.2 Exemptions
The provisions of this Code do not apply to: Buildings that do not use either electricity or fossil fuel Equipment and portions of building systems that use energy primarily for manufacturing processes

2.3 Safety, Health, And Environmental Codes Take Precedence

Where this Code is found to conlict with safety, health, or environmental codes, the safety, health, or environmental codes shall take precedence.

2.4 Reference Standards

National Building Code (NBC) 2005 is the reference document/standard for lighting levels, HVAC, comfort levels, natural ventilation, pump and motor eficiencies, transformer eficiencies and any other building materials and system performance criteria. The National Building Code 2005 has also been used as a reference in this Guide. The Code is a dynamic document under continuous maintenance. Addenda, errata, and interpretations can be issued as and when necessary by the concerned authorities such as the Ministry of Power, the Bureau of Energy Eficiency, the state governments, etc. This Guide is consistent with ECBC 2007 (revised version, May 2008). Designers using this Guide should conirm if any addendum has been adopted in the Code by the Authority Having Jurisdiction before incorporating its requirements in the proposed buildings design.

Energy Conservation Building Code (ECBC) User Guide

Administration and Enforcement

3. Administration and Enforcement1

his chapter addresses administration and enforcement issues, as well as general requirements for demonstrating compliance with the Code. The compliance requirements of the Code have been made lexible enough to allow architects and engineers the ability to comply with the Code and meet the speciic needs of their projects according to the climatic conditions of the site.

3.1 Compliance Requirements

As mentioned in Chapter 2, all the buildings or building complexes with a connected load of 500 kW or greater or a contract demand of 600 kVA or greater have to comply with the Code. Buildings with 1,000 m2 or more of conditioned area are likely to fall under the above load conditions. The following sections which deal with mandatory and prescriptive requirements of new and existing buildings are related to this speciied threshold area. It is important to mention here that these mandatory and prescriptive requirements are applicable only where the building has a connected load of 500 kW or more or contract demand of 600kVA or more.

3.1.1

Mandatory Requirements

Compliance with the requirements of the Code shall be mandatory for all applicable buildings mentioned under Chapter 2 of the Code.

3.1.2

New Buildings

The Code compliance procedure requires the new building to fulill a set of mandatory provisions related to energy use as well as show compliance with the speciied requirements stipulated for the different building components and systems. The mandatory requirements are described in Sections 4.2, 5.2, 6.2, 7.2, and 8.2 of the Code. These mandatory provisions are discussed in the corresponding sections of this Guide. The Code also speciies prescriptive requirements for building components and systems. However, to maintain lexibility for the design and construction team, the Code compliance requirements can be met by following one of two methods: 1. Prescriptive Method speciies prescribed minimum energy eficiency parameters for various components and systems of the proposed building. The prescriptive requirements are covered in Chapter 4 through Chapter 8 dealing with the building envelope, HVAC systems, service hot water and pumping, lighting systems, and electric power respectively. To use the building envelope section as an example, designers can choose the prescriptive method that offers lexibility in selecting insulation for roof that meets speciied thermal characteristic (e.g. R-value, discussed in Chapter 4 of this Guide), in place of meeting prescriptive requirements of U-factor of the roof assembly. More explanation related to this method can be found in 3.2. 2. Whole Building Performance (WBP) is an alternative method to comply with the Code. This method is more complex than the Prescriptive Method, but offers considerable design lexibility. It allows for Code compliance to be achieved by optimizing the energy usage in various building components and systems (envelope, HVAC, lighting and other building systems) in order to ind the most cost-effective solution. WBP method requires an approved computer software program to model a Proposed Design, determine its annual energy use and compare it with the Standard Design of the building. Further explanation on the WBP Method can also be found in 3.2.

This Chapter has been adapted from ASHRAE User Manual (2004).

Energy Conservation Building Code (ECBC) User Guide

Administration and Enforcement

Box 3-A provides an overview of the ECBC compliance process.

Box 3-A: Steps for meeting ECBC Compliance

3.1.3

Additions to Existing Buildings

Existing Building Compliance The Code also applies to additions in existing buildings. The requirements are triggered when new construction is proposed in the existing building. As per the Code: Where the addition plus the existing building exceeds the conditioned loor area of 1,000 m2 or more, the additions shall comply with the provisions of Chapter 4 through Chapter 8. Compliance may be demonstrated in either of the following ways: The addition alone shall comply with the applicable requirements, or The addition, together with the entire existing building, shall comply with the requirements of this Code that would apply to the entire building, as if it were a new building Exception to above: When space conditioning is provided by existing systems and equipment, the existing systems and equipment need not comply with this Code. However, any new equipment installed must comply with speciic requirements applicable to that equipment.

Example 3.1: ECBC Compliance for Additions to Existing Building

An existing warehouse measures 120 m 60 m. The warehouse is unconditioned, and the administrative ofice (30 m 30 m) located in one corner. The ofice is served by a single-zone rooftop packaged HVAC system that provides both heating and cooling. The owner wants to expand the administrative ofice into the warehouse. The new ofice space will convert an area that measures 30 m 15 m from unconditioned to conditioned space. The existing HVAC system has suficient capacity to serve the additional space. However, new ductwork and supply registers will need to be installed to serve the additional space.

Energy Conservation Building Code (ECBC) User Guide

Administration and Enforcement

A: Area of Existing Ofice = 30m 30m = 900m2 Additional Area of Ofice = 30m 15m = 450m2 However, the Code applies to the 30m 45m space that is being converted from unconditioned to conditioned space. The Code does not apply to the existing ofice or the existing warehouse space. The existing HVAC system does not need to be modiied, but the ductwork extensions must be insulated to the requirements of 5. The new lighting system installed in the ofice addition must meet the requirements of 7. The walls that separate the ofice addition from the unconditioned warehouse must be insulated to the requirements of 4. The exterior wall and roof are exterior building envelope components and must meet the Code requirements. Source: Adapted from ASHRAE User Manual (2004).

3.1.4

Alterations to Existing Buildings

When making alterations to an existing building, the portions of a building and its systems that are being altered must be made to comply with mandatory and prescriptive requirements. As per the Code: Where the existing building exceeds the conditioned loor area threshold (of 1000 m2 or more), portions of a building and its systems that are being altered shall meet the provisions of Chapter 4 through Chapter 8 (of the Code). The speciic requirements for alterations are described in the following subsections. Exception to above: When the entire building complies with all of the provisions of Chapter 4 through Chapter 8 (of the Code) as if it were a new building.

3.1.4.1 Building Envelope

As per the Code: Alterations to the building envelope shall comply with the requirements of Chapter 4 (of the Code) or fenestration, insulation, and air leakage applicable to the portions of the buildings and its systems being altered. Exception to above: The following alterations need not comply with these requirements provided such alterations do not increase the energy usage of the building: Replacement of glass in an existing sash and frame, provided the U-factor and SHGC of the replacement glazing are equal to or lower than the existing glazing Modiications to roof/ceiling, wall, or loor cavities, which are insulated to full depth with insulation Modiications to walls and loors without cavities and where no new cavities are created

3.1.4.2 Heating, Ventilation, and Air Conditioning

As per the Code: Alterations to building heating, ventilating, and air-conditioning equipment or systems shall comply with the requirements of Chapter 5 (of the Code) applicable to the portions of the building and its systems being altered. Any new equipment or control devices installed in conjunction with the alteration shall comply with the speciic requirements applicable to that equipment or control device.

Energy Conservation Building Code (ECBC) User Guide

Administration and Enforcement

3.1.4.3 Service Water Heating

As per the Code: Alterations to building service water heating equipment or systems shall comply with the requirements of Chapter 6 applicable to the portions of the building and its systems being altered. Any new equipment or control devices installed in conjunction with the alteration shall comply with the speciic requirements applicable to that equipment or control device.

3.1.4.4 Lighting
As per the Code: Alterations to building lighting equipment or systems shall comply with the requirements of Chapter 7 applicable to the portions of the building and its systems being altered. New lighting systems, including controls, installed in an existing building and any change of building area type as listed in Table 7.1 shall be considered an alteration. Any new equipment or control devices installed in conjunction with the alteration shall comply with the speciic requirements applicable to that equipment or control device. Exception to above: Alterations that replace less than 50% of the luminaires in a space need not comply with these requirements provided such alterations do not increase the connected lighting load.

3.1.4.5 Electric Power and Motors

As per the Code: Alterations to building electric power systems and motors shall comply with the requirements of Chapter 8 applicable to the portions of the building and its systems being altered. Any new equipment or control devices installed in conjunction with the alteration shall comply with the speciic requirements applicable to that equipment or control device.

3.2 Compliance Approaches

The Code requires that the building shall comply irst with all the mandatory provisions discussed in Chapter 4 to 8 (of the Code). But every building project is different: each building has its own site that presents unique opportunities and challenges, each building owner or user has different requirements, and climate and microclimate conditions can vary signiicantly among projects. Architects and engineers need lexibility in order to design buildings that address these diverse requirements. The Code provides this lexibility in a number of ways. Building components and systems have multiple options to comply with the Code requirements. To use the building envelope section as an example, designers can choose the Prescriptive Method that requires roof insulation be installed with a minimum R-value. Alternatively, the other options allow the designer to show compliance with the thermal performance (U-factor) of roof construction assembly. In addition building envelope tradeoff option discussed in Chapter 4 permits trade-offs among building envelope components (roof, walls, and fenestration) for Code compliance. If more lexibility is needed, the Whole Building Performance Method is available. a. Prescriptive Method The Code speciies a set of prescriptive requirements for building systems and components. Compliance with the Code can be achieved by meeting or exceeding the speciic levels described for each individual element of the building systems, covered in Chapter 4 through Chapter 8 of the Code. For building envelope, the Code provides a Trade-Off option that allows trading off the eficiency of one envelope element with another to achieve the overall eficiency level required by the Code. The envelope trade-off option is discussed in Chapter 12: Appendix D of ECBC.

Energy Conservation Building Code (ECBC) User Guide

Administration and Enforcement

b. Whole Building Performance Method Use of energy simulation software is necessary to show ECBC compliance via the Whole Building Performance Method. Energy simulation is a computer-based analytical process that helps building owners and designers to evaluate the energy performance of a building and make it more energy-eficient by making necessary modiications in the design before the building is constructed. These computer-based energy simulation programs model the thermal, visual, ventilation, and other energyconsuming processes taking place within the building to predict its energy performance. The simulation program takes into account the building geometry and orientation, building materials, building faade design and characteristics, climate, indoor environmental conditions, occupant activities and schedules, HVAC and lighting system and other parameters to analyze and predict the energy performance of the building. Computer simulation of energy use can be accomplished with a variety of computer software tools and in many cases may be the best method for guiding a building project to be energy-eficient. However, this approach does require considerable knowledge of building simulation tools and very close communication between members of the design team. Appendix B of the Code describes the Whole Building Performance Method for complying with the Code. This method involves developing a computer model of the Proposed Design and comparing its energy consumption to the Standard Design for that building. Energy consumption in the Standard Design represents the upper limit of energy use allowed for that particular building under a scenario where all the prescriptive requirements of the Code are adopted. Code compliance will be achieved if the energy use in Proposed Design is no greater than the energy used in the Standard Design. Three basic steps are involved: 1. Design the building with energy eficiency measures; the prescriptive approach requirements provide a good starting point for the development of the design. 2. Demonstrate that the building complies with the mandatory measures (See sections 4.2, 5.2, 6.2, 7.2, and 8.2). 3. Using an approved simulation software, model the energy consumption of the building using the proposed features to create the Proposed Design. The model will also automatically calculate the energy use for the Proposed Design. If the energy use in Proposed Design is no greater than the energy use in the Standard Design, the building complies with the Code. Figure 3.1 shows a schematic depicting the WBP method

Figure 3.1: Design Process for the Whole Building Performance Method

The biggest advantage of using this approach is that it enables the design and construction team to make comparisons between different design options to identify the most cost-effective and energy-eficient design solution. For instance, the eficiency of the indoor lighting system might be improved in order to justify

Energy Conservation Building Code (ECBC) User Guide

Administration and Enforcement

fenestration design that does not meet the prescriptive envelope requirements. As long as the total energy use of the Proposed Design does not exceed the allowed energy use in Standard Design, the building will be ECBC compliant. Note: For a detailed description of the computer simulation process and details, please refer to the Energy Simulation Tip Sheet which can be accessed at: http://eco3.org/downloads/002-Implementationof ECBC/ Energy Simulation (Public Version).pdf

3.3 Administrative Requirements

As per the Code: Administrative requirements relating to permit requirements, enforcement, interpretations, claims of exemption, approved calculation methods, and rights of appeal are speciied by the Authority Having Jurisdiction. Administration and enforcement of the Code is carried out by the local Authority Having Jurisdiction. This authority can be responsible for specifying permit requirements, code interpretations, approved calculation methods, worksheets, compliance forms, manufacturing literature, rights of appeal, and other data to demonstrate compliance. The Authority Having Jurisdiction will need to receive plans and speciications that show all pertinent data and features of the building, equipment, and systems. The process of designing code-compliant buildings will include different stages that begin with the design process, obtaining a building permit, completing the compliance submittals, the construction of the building followed by periodic inspections to make sure that construction is taking place per the requirement of the Code. Box 3-B discusses the Integrated Design Approach and Box 3-C provides guidelines for introducing the Code compliances and enforcement process. The process of complying with and enforcing the Code will require the involvement of many parties. Those involved may include the architect or building designer, building developer, contractor, engineers, energy consultant, owner, oficials doing compliance check, and third-party inspectors. Communication between these parties and an integrated design approach will be essential for the compliance/ enforcement process to run eficiently.

Box 3-B: Integrated Design Approach

An integrated design approach brings together the various disciplines involved in designing a building and its systems and reviews their recommendations in a comprehensive manner. It recognizes that each disciplines recommendations have an impact on other aspects of the building project. This approach allows for optimization of both building performance and cost. Often, the architect, mechanical engineer, electrical engineer, contractors, and other team members pursue their scope of work without adequate interaction with other team members. This can result in oversized systems or systems that are not optimized for eficient performance. For example, indoor lighting systems designed without consideration of day lighting opportunities or HVAC systems designed independently of lighting systems. An integrated design approach allows professionals working in various disciplines to take advantage of eficiencies that are not apparent when they are working in isolation. It can also point out areas where trade-offs can be implemented to enhance resource eficiency. The earlier that integration is introduced in the design process, the greater the beneit.

Box 3-C: The Compliance and Enforcement Process

Although the compliance and enforcement process may vary somewhat with each adopting jurisdiction, the enforcement authority is generally the building department or other agency that has responsibility for approving and issuing building permits. When non-compliance or omissions are discovered during the plan review process, the building oficial may issue a correction list and require the plans and applications to be revised to bring them into compliance prior to issuing a building permit. In addition, the building oficial has the authority to stop work during construction when a code violation is discovered.

Energy Conservation Building Code (ECBC) User Guide

Administration and Enforcement

The local building department has jurisdiction for determining the administrative requirements relating to permit applications. They are also the inal word on interpretations, claims of exemption, and rights of appeal. From time to time, the concerned authority will issue interpretations clarifying the intent of the Code. The local building department may take these under consideration, but the local building department still has the inal word. To achieve the greatest degree of compliance and to facilitate the enforcement process, the Code should be considered at each phase of the design and construction process (see Figure 3.2). 1. At the design phase, designers must understand both the requirements and the underlying intent of the Code. The technical sections of this Guide provide information that designers need to understand how the Code applies both to individual building systems and to the integrated building design. 2. At permit application, the design team must make sure that the construction documents submitted with the permit application contain all the information that the building oficial will need to verify that the building satisies the requirements of the Code. (This Guide provides compliance forms and worksheets to help ensure that all the required information is submitted.) 3. During plan review, the building oficial must verify that the proposed work satisies the requirements of the Code and that the plans (not just the forms) describe a building that complies with the Code. The building oficial may also make a list of items to be veriied later by the ield inspector. 4. During construction, the contractor must carefully follow the approved plans and speciications. The design professional should carefully check the speciications and working drawings that demonstrate compliance and should observe the construction in progress to see that compliance is achieved. The building oficial must verify that the building is constructed according to the plans and speciications. 5. After completion of construction, the contractor and/or designer should provide information to the building operators on maintenance and operation of the building and its equipment. Although only minimal completion and commissioning is required by the Code, most energy eficiency experts agree that full commissioning is important for proper building operation and management. Figure 3.2 maps the Design and Construction process along with the Compliances/Enforcement steps needed to show ECBC compliance.

Figure 3.2: The Building Design and Construction Process

Energy Conservation Building Code (ECBC) User Guide

Administration and Enforcement

3.4 Compliance Documents

3.4.1 General
As per the Code: Plans and speciications shall show all pertinent data and features of the building, equipment, and systems in suficient detail to permit the Authority Having Jurisdiction to verify that the building complies with the requirements of this code. Details shall include, but are not limited to: Building Envelope: Insulation materials and their R-values Fenestration U-factors, SHGC, visible light transmittance (if using the trade-off approach), and air leakage Overhang and sidein details Envelope sealing details HVAC: Type of systems and equipment, including their sizes, eficiencies, and controls Economizer details Variable speed drives Piping insulation Duct sealing Insulation type and location Report on HVAC balancing Service Hot Water and Pumping: Solar water heating system details Lighting: Schedules that show type, number, and wattage of lamps and ballasts Automatic lighting shutoff details Occupancy sensors and other lighting control details Lamp eficacy for exterior lamps Electrical Power: Schedules that show transformer losses, motor eficiencies, and power factor correction devices Electric check metering and monitoring system details The documents submitted should include suficient detail to allow thorough review by the Authority Having Jurisdiction for Code compliance. Additional information may be requested by the authority, if needed, to verify compliance. The compliance forms and worksheets are provided with this Guide (Appendix G) and are intended to facilitate the process of complying with the Code. These forms serve a number of functions: They provide a permit applicant and designer the information that needs to be included on the drawing. They provide a structure and order for the necessary calculations. The forms allow information to be presented in a consistent manner, which is a beneit to both the permit applicant and the enforcement agency.

Energy Conservation Building Code (ECBC) User Guide

10

Administration and Enforcement

They provide a roadmap showing the enforcement agency where to look for the necessary information on the plans and speciications. They provide a checklist for the enforcement agency to help structure the drawing check process. They promote communication between the drawings examiner and the ield inspector. They provide a checklist for the inspector.

3.4.2

Supplemental Information

As per the Code: The Authority Having Jurisdiction may require supplemental information necessary to verify compliance with this Code, such as calculations, worksheets, compliance forms, manufacturers literature, or other data.

Energy Conservation Building Code (ECBC) User Guide

11

Building Envelope

4. Building Envelope
4.1 General
Overview

envelope refers is comprised of opaque components and The building systems. Opaque to the exterior faade, androofs, slabs on grade (in touch with ground), fenestration components include walls, basement walls, and opaque doors. Fenestration systems include windows, skylights, ventilators, and doors that are more than one-half glazed. The envelope protects the buildings interior and occupants from the weather conditions and shields them from other external factors e.g. noise, air pollution, etc.

The building envelope depicted here by the green line, which separates the conditioned space from the unconditioned space.

Figure 4.1: Building Envelope Envelope design strongly affects the visual and thermal comfort of the occupants, as well as energy consumption in the building. Box 4-A discusses the there modes of heat transfer (Conduction, Convection and Radiation) in the building.

Box 4-A: How Heat Transfer Takes Place in a Building

Heat transfer takes place through walls, windows, and roofs in buildings from higher temperature to lower temperature in three ways-conduction, convection, and radiation. Conduction is the transfer of heat by direct contact of particles of matter within a material or materials in physical contact. Convection is the transfer of heat by the movement of a luid (air or gas or liquid). Radiation is the movement of energy/heat through space without relying on conduction through the air or by the movement of air. The surface of the sun, estimated to be at a temperature of about 5500C, emits electromagnetic waves. These waves are also known as solar radiation or short-wave radiation with wave length in the range of 0.3 to 2.5 microns or 300 nm to 2500 nm, and has three components: Ultra Violet (UV), Visible (the sun light which is visible to human eye) and Solar (or Near) Infrared as depicted in the igure Figure 4.2:

Energy Conservation Building Code (ECBC) User Guide

12

Building Envelope

Figure 4.2: The Solar and Blackbody Spectrum When the Solar Infrared component of the waves comes in contact with the earth or any object or a building, it transfers its energy to the object/building in the form of heat. The phenomenon is known as solar radiation heat transfer. Radiation heat transfer, in fact, can be between any two bodies having different temperatures with heat transfer taking place from the body at higher temperature to the body at the lower temperature. The Figure 4.3 shows all three modes of heat transfer across a building wall facing the external environment.

Figure 4.3: Schematic Showing Three Modes of Heat Transfer Conductive heat transfer across the envelope also depends upon the conductivity of the building material used. Different materials offer different thermal resistance to the conduction process. Individually, walls and roofs are comprised of a number of layers composed of different building materials. Thus, it is important to establish overall thermal resistance and heat transfer coeficient (U-factor), also termed thermal transmittance. The concepts of thermal resistance and U- factor are discussed in Box 4-B for better understanding.

Energy Conservation Building Code (ECBC) User Guide

13

Building Envelope

Box 4-B: Conduction and Resistance

Conduction Conduction is heat transfer through a solid medium as a result of a temperature gradient. The heat low direction is, in accordance with the second law of thermodynamics, from a region of higher temperature to that of lower temperature. The Conductivity is the property of material. The rate of heat transfer (q) through a homogeneous medium is given by Fouriers Law of Conduction: dT q = kA dx 6 W @ q : Rate of heat transfer [W] k A T x : Thermal conductivity of the material [Wm2K-1] : Area [m2] : Temperature [K] : Distance in the direction of heat low [m]

Resistance Thermal Resistance is proportional to the thickness of material of construction and inversely proportional to its conductivity. This, a lower value of conductivity means less heat low and so does the greater thickness of material. Together these parameters form the Thermal Resistance to the process of heat conduction. d R = k 6 m2 K W- 1 @ Description of Surface Resistance The total thermal resistance RT of a plane element consisting of thermally homogeneous layers perpendicular to the heat low is calculated by the following formula: RT : Rsi + Rt + Rse Where Rt is the thermal resistances of the component in the wall/roof. Rt : R1 + R2+ + Rn For the calculation of the thermal transmittance under ordinary building conditions, the seasonal mean values of the exterior surface thermal resistance (Rse) and the interior surface thermal resistance (Rsi) can be obtained from Table 4.1. These values are the result of empirical studies and merely represent magnitudes of order. They consider both convection and radiation inluences. Table 4.1: Values of Surface Film Resistance Based on Direction of Heat Flow Rsi
Direction of Heat Flow Horizontal Up
0.13 0.10

Rse
Down
0.17

Direction of Heat Flow Horizontal Up

0.04 0.04

Down
0.04

Thermal Resistance of an Element Consisting of Homogenous Layers A building element is usually composed of a number of different materials. When materials are placed in series, their thermal resistances are added so that the same area will conduct less energy for a given temperature difference. Formation of air ilm at the surface of wall or roof, due to convection movements of air, also provides resistance to the heat low, similar to the construction material. The total resistance of the wall or roof includes all of the resistances of the individual materials that make it up as well as both the internal and external air-ilm resistance. R1, R2, , Rn are the thermal resistance of each layer. 1 Thermal Resistance is also depicted as reciprocal of Thermal Conductance (U): R = U

Energy Conservation Building Code (ECBC) User Guide

14

Building Envelope

Thermal Resistance of Unventilated Air Layers Table 4.2 gives the thermal resistances of unventilated air layers (valid for emittance of the bounding surfaces > 0.8). The values under "horizontal" should be used for heat low directions 30 from the horizontal plane; for other heat low directions, the values under "up" or "down" should be used. Table 4.2: Thermal Resistances of Unventilated Air Layers Between Surfaces with High Emittance Thickness of Air Layer (mm)
Horizontal
5 7 10 15 25 50 100 300 0.12 0.12 0.14 0.16 0.18 0.18 0.18 0.18

Thermal Resistance (m2KW-1) Direction of Heat Flow

Up
0.10 0.12 0.14 0.16 0.17 0.17 0.17 0.17

Down
0.10 0.12 0.14 0.16 0.18 0.20 0.20 0.21

Example 4.1: R -Value Calculations for Cavity Wall Construction

Figure 4.4: Typical Cavity Wall Construction R1: Resistance for Layer 1 (13 mm Gypsum Plaster) = 0.056 K 2/W (from ECBC Table 11.4) m R2: Resistance of Layer 2 (230 mm brick wall, density=1920kg/m3) = d2/k2 = 0.230/0.81 =0.284 K 2/W m R3: Resistance of Layer 3 (115 mm air gap) (from ECBC Table 11.4) =1.8 Km2/W (from Table 4.1)

R4: Resistance of Layer 4 (115 mm brick wall, density=1920kg/m3) = d4/k4 = 0.115/0.81 =0.1426 K 2/W m (from ECBC Table 11.4) Rt: Minimum R-value for the composite wall RT: Rsi+ Rt+R se Maximum U-factor for the composite wall: Umin = R1+ R2+ R3 + R4 = 0.056+ 0.2840 + 0.18 + 0.1426 = 0.6626 Km2/W = 0.1+ 0.6626 +0.04= 0.8026 = 1/RT = 1/0.8026 = 1.246 W/m2K

The design of the building envelope is generally the responsibility of an architect. The building designer is responsible for making sure that the building envelope is energy-eficient and complies with the mandatory
Energy Conservation Building Code (ECBC) User Guide 15

Building Envelope

and prescriptive requirements of the Code. It also provides trade-off options which allows lexibility to the designer to trade-off prescriptive requirements of building components, while meeting the minimum energy performance requirements of the envelope.

4.2 Mandatory Requirements

4.2.1 Fenestration
Heat transfer across glazing products or fenestration (windows, door, and skylights) is similar to the heat transfer that takes place across walls and roofs through conduction and convection. So, U-factor of glazing is analogous to the U-factor of wall assembly. In addition, direct solar radiation contributes to the solar heat gain through the fenestration system. Box 4-C discusses the concept of Solar Heat Gain Coeficient (SHGC). Fenestration and doors must be rated using procedures and methods speciied in the ECBC. Three fenestration performance characteristics are signiicant in the ECBC: U-factor, SHGC, and Visible Light Transmittance (VLT). These are reviewed below: The U-factor of fenestration is very important to the energy eficiency of buildings, especially in cold climates. The U-factor must account for the entire fenestration product, including the effects of the frame, the spacers in double glazed assemblies, and the glazing. There are a wide variety of materials, systems, and techniques used to manufacture fenestration products, and accurately accounting for these factors is of utmost importance when calculating the U-factor. According to ECBC, Fenestration U-factors must be determined in accordance with ISO-15099.

Box 4-C: Solar Heat Gain Coeicient and U-Factor

Conduction heat low through the fenestration (e.g. glass windows) is similar to the process discussed for walls and roofs. However regardless of outside temperature, heat gain through the fenestration is also dependent on direct and indirect solar radiation. The ability to control this heat gain is characterized in terms of SHGC. SHGC is the ratio of the solar heat gain that passes through the fenestration to the total incident solar radiation that falls on the fenestration. The solar heat gain includes directly transmitted solar heat and absorbed solar radiation, which is then re-radiated, convected, or conducted into the interior space. SHGC indicates how well the glazing/glass and fenestration products insulate heat caused by sun falling directly on the glass.

Figure 4.5: Direct and Indirect Solar Radiation In hot climates, SHGC is more important than the U-factor of the glazing. A lower SHGC means that lesser heat can pass through the glazing. The SHGC is based on the properties of the glazing material, whether the window has single, double, or triple glazing, and the window operation (either operable or ixed). Glazing units with a low SHGC will help reduce the air conditioning energy use during the cooling season.

Energy Conservation Building Code (ECBC) User Guide

16

Building Envelope

Figure 4.6: Heat Transfer (Conduction, Convection, & Radiation) and Iniltration Across a Window

4.2.1.1 U-factors
Clear glass, which is the most common type of glass used today, has no signiicant thermal resistance (R-value) from the pane itself. It has a value of R-0.9 to R-1.0 due to the thin ilms of air on the interior and exterior surfaces of the glass. The U-factor (thermal conductance), must account for the entire fenestration system including the effects of the frame, the spacers in double glazed assemblies, and the glazing. There are a wide variety of materials, systems, and techniques used to manufacture fenestration products, and accurately accounting for these factors is of utmost importance when meeting the fenestration requirements. The Code also speciies U-factor for sloped glazing and skylights, and minimum U-factors for unrated products. ECBC has used W/m2C as the unit for U-factor. Since differences in temperature are always denoted in K in physics literature, ECBC User Guide has used W/m2K as the unit of U-factor. Wherever, C was being used for differences in temperature, it has been replaced with K in the Guide. U-factors for fenestration systems (including the sash and frame) are required to be determined in accordance with ISO-15099 (as speciied in ECBC 11: Appendix C) by an accredited independently laboratory and labeled and certiied by the manufacturer or other responsible party. Box 4-D briely explains how these issues are addressed in US.

Box 4-D: How Fenestration Products are Tested, Certiied, and Labeled in the U.S.
In the U.S, the fenestration U-factors are determined in accordance with the National Fenestration Rating Council (NFRC) Standard 100. NFRC is a membership organization of window manufacturers, researchers, and others that develops, supports, and maintains fenestration rating and labeling procedures. Most fenestration manufacturers have their products rated and labeled through the NFRC program. Certiied products receive an 8 by 11 inch NFRC label that lists the U-factor, SHGC, and the visible transmittance.

4.2.1.2 Solar Heat Gain Coeicient

The ECBC requires that SHGC be determined in accordance with ISO-15099 by an accredited independent laboratory, and labeled and certiied by the manufacturer or other responsible party. SHGC has replaced Shading Coeficient (SC) as the preferred speciication for solar heat gain through fenestration products. Designers should insist on getting SHGC data from the manufacturers. However, it should be kept in mind that only SHGC data that is certiied by an accredited independent testing laboratory can be used to show ECBC compliance.

Energy Conservation Building Code (ECBC) User Guide

17

Building Envelope

4.2.1.3 Air Leakage

Air leakage for glazed swinging entrance doors and revolving doors shall not exceed 5.0 l/sm2. Air leakage for other fenestration and doors shall not exceed 2.0 l/sm2. The irst set of air leakage requirements deals with inadvertent leaks at joints in the building envelope. In particular, the standard states that exterior joints, cracks, and holes in the building envelope shall be caulked, gasketed, weather stripped, or otherwise sealed. The construction drawings should specify sealing, but special attention is needed in the construction administration phase to assur e proper workmanship. A tightly constructed building envelope is largely achieved through careful construction practices and attention to detail. Poorly sealed buildings can cause problems for maintaining comfort conditions when additional iniltration loads exceed the HVAC design assumptions. This can be a signiicant problem in high-rise buildings due to stack effect and exposure to stronger winds.

4.2.2

Opaque Construction

U-factors shall be determined from the default tables in Appendix C 11 or determined from data or procedures contained in the ASHRAE Fundamentals, 2005.

4.2.3

Building Envelope Sealing

Air leakage can also occur through opaque construction. Apart from adding cooling or heating load in the building, air leakage can cause condensation within walls and roof can damage insulation material and degrade other building materials. Box 4-E discusses these aspects in more detail. It must be noted that building sealing is more important in air-conditioned buildings. In naturally ventilated buildings, the concept of building ceiling and tight envelope runs counter to conventional and traditional wisdom.

Box 4-E: Building Envelope Sealing and Air Leakage

Air leakage is the passage of air through a building envelope, wall, window, joint, etc. Leakage to the interior is referred to as iniltration and leakage to the exterior is referred to as ex-iltration. Excessive air movement signiicantly reduces the thermal integrity and performance of the envelope and is, therefore, a major contributor to energy consumption in a building. A tightly constructed building envelope is largely achieved through careful construction practices and attention to detail. Building envelopes should be carefully designed to limit the uncontrolled entry of outdoor air into the building. Air leakage introduces sensible heat into conditioned spaces. In climates with moist outdoor conditions, it is also a major source of latent heat. Latent heat must be removed by the air-conditioning system at considerable expense. In addition to causing energy loss, excessive air leakage can cause condensation to form within and on walls. This can create many problems including reducing insulation R-value, permanently damaging insulation, and seriously degrading materials. It can rot wood, corrode metals, stain brick or concrete surfaces, and in extreme cases cause concrete to break, bricks to separate, mortar to crumble and sections of a wall to fall jeopardizing the safety of occupants. It can corrode structural steel, re-bar, and metal hangars and bolts with very serious safety and maintenance consequences. Moisture accumulation in building materials can lead to the formation of mold that may require extensive remedying the situation. Virtually anywhere in the building envelope where there is a joint, junction or opening, there is potential for air leakage. Air leakage will cause the HVAC system to run more often and longer at one time, and still leave the building uncomfortable for its occupants. All openings in the building envelope, including joints and other openings that are potential sources of air leakage, should be to be sealed to minimize air leakage. It means that all gaps between wall panels, around doors, and other construction joints must be well sealed. Ceiling joints, lighting ixtures, plumbing openings, doors, and windows should all be considered as potential sources of unnecessary energy loss due to air iniltration. ECBC identiies several areas in the building envelope where attention should be paid to iniltration control. These include:

Energy Conservation Building Code (ECBC) User Guide

18

Building Envelope

a. Joints around fenestration and doorframes. b. Openings at penetrations of utility services through roofs, walls, and loors. c. Site-built fenestration and doors. d. Building assemblies used as ducts or plenums. e. Joints, seams, and penetrations of vapor retarders. f. All other openings in the building envelope. It is also recommended that junctions between walls and foundations, between walls at building corners, between walls and structural loors or roofs, and between walls and roof or wall panels. Fenestration products, including doors, can also signiicantly contribute to iniltration. Although not included in the Code, it is recommended that fenestration products should have iniltration less than 0.4 cfm/ft (2.0 l/sm). For glazed entrance doors that open with a swinging mechanism and for revolving doors, it is recommended that iniltration be limited to 1.0 cfm/ft (5.0 l/sm).

4.3 Prescriptive Requirements

For envelope component-based compliance approach, ECBC sets requirements for: Exterior roofs and ceilings Cool roofs Opaque walls Vertical fenestration Skylights

4.3.1

Roofs

In roofs, the U-factor for the overall assemblies or minimum R-values for the insulation must be complied with the provisions of the Code. ECBC Appendix C provides values for typical constructions. In real practice, the heat gains through the walls, roof, and fenestration depends upon the climate zone in which the building is located. The National Building Code of India, 2005 has divided the country in ive climate zones (Hot-Dry; Warm-Humid; Composite; Temperate/Moderate; and Cold), and the air temperature and humidity variations that exist need to be considered while designing the building envelope.

Box 4-F: Role of Climate Zone

The ECBC building envelope requirements are based on the climate zone in which the building is located. ECBC deines ive climate zones (hot-dry; warm-humid; composite; temperate; cold), which are distinctly unique in their weather proiles. Appendix E of the Guide provides additional information on the ive climatic zones. Based on the characteristics of climate, the thermal comfort requirements in buildings and their physical manifestation in architectural form are also different for each climate zone (See Table 4.3). These physical manifestations, in turn, dictates the ECBC requirements for the envelope, as well as other building components that are applicable to the building. Table 4.3: Comfort Requirements and Physical Manifestations in Buildings HOT AND DRY CLIMATE ZONE
Thermal Requirements Reduce Heat Gain
Decrease exposed surface area Increase thermal resistance Increase thermal capacity (Time lag) Increase buffer spaces Decrease air exchange rate (ventilation during day-time) Increase shading Orientation and shape of building Insulation of building envelope Massive structure Air locks/lobbies/balconies/verandahs Smaller windows openings, night ventilation External surfaces protected by overhangs, ins and trees

Physical Manifestation

Energy Conservation Building Code (ECBC) User Guide

19

Building Envelope

Increase surface relectivity Reduce solar heat gain

Pale colour, glazed china mosaic tiles etc. Use glazing with lower SHGC and provide shading for windows. Minimize glazing in East and West Courtyards/wind towers/arrangement of openings Trees, water ponds, evaporative cooling

Promote Heat Loss

Increase air exchange rate (Ventilation during night-time) Increase humidity levels

WARM AND HUMID CLIMATE ZONE

Thermal Requirements Reduce Heat Gain
Decrease exposed surface area Increase thermal resistance Orientation and shape of building Roof insulation and wall insulation Relective surface of roof Increase buffer spaces Increase shading Increase surface relectivity Reduce solar heat gain Balconies and verandas Walls, glass surfaces protected by overhangs, ins and trees Pale color, glazed china mosaic tiles, etc. Use glazing with lower SHGC and provide shading for windows. Minimize glazing in East and West Ventilated roof construction. Courtyards, wind towers and arrangement of openings Dehumidiiers/desiccant cooling

Physical Manifestation

Promote Heat Loss

Increase air exchange rate (Ventilation throughout the day) Decrease humidity levels

Thermal Requirements Reduce Heat Gain

Decrease exposed surface area Increase thermal resistance Increase shading Increase surface relectivity

MODERATE CLIMATE ZONE Physical Manifestation

Orientation and shape of building Roof insulation and east and west wall insulation East and west walls, glass surfaces protected by overhangs, ins and trees Pale colour, glazed china mosaic tiles, etc. Courtyards and arrangement of openings

Promote Heat Loss

Increase air exchange rate (Ventilation)

COLD (Cloudy/Sunny) CLIMATE ZONE

Thermal Requirements Reduce Heat Loss
Decrease exposed surface area Increase thermal resistance Increase thermal capacity (Time lag) Increase buffer spaces Decrease air exchange rate Increase surface absorptive Orientation and shape of building. Use of trees as wind barriers Roof insulation, wall insulation and double glazing Thicker walls Air locks/Lobbies Weather stripping and reducing air leakage Darker colours Walls and glass surfaces Sun spaces/green houses/Trombe walls etc.

Physical Manifestation

Promote Heat Gain

Reduce shading Trapping heat

COMPOSITE CLIMATE ZONE

Thermal Requirements Reduce Heat Gain in Summer and Reduce Heat Loss in Winter
Decrease exposed surface area Increase thermal resistance Increase thermal capacity (Time lag) Orientation and shape of building. Use of trees as wind barriers Roof insulation and wall insulation Thicker walls

Physical Manifestation

Energy Conservation Building Code (ECBC) User Guide

20

Building Envelope

Increase buffer spaces Decrease air exchange rate Increase shading Increase surface relectivity Reduce solar heat gain

Air locks/Balconies Weather stripping Walls, glass surfaces protected by overhangs, ins and trees Pale color, glazed china mosaic tiles, etc. Use glazing with lower SHGC and provide shading for windows. Minimize glazing in East and West Courtyards/wind towers/arrangement of openings Trees and water ponds for evaporative cooling Dehumidiiers/desiccant cooling

Promote Heat Loss in Summer/Monsoon

Increase air exchange rate (Ventilation) Increase humidity levels in dry summer Decrease humidity in monsoon

Source: Nayak and Prajapati (2006). Handbook on Energy Conscious Buildings

Exterior roofs can meet the prescriptive requirements in one of two ways: Use the required R-value of the insulation (this R-value does not apply to building materials or air ilm. It should be referred exclusively for insulation), or Use a roof assembly U-factor that meets the maximum U-factor criterion for thermal performance (see ECBC Table 4.3.1). The U-factor takes into account all elements or layers in the construction assembly, including the sheathing, interior inishes, and air gaps, as well as exterior and interior air ilms. As per the Code: The roof insulation shall not be located on a suspended ceiling with removable ceiling panels. The Code requirements for the U-factor and R-values for 24 hours use buildings and daytime use buildings for ive climate zones as shown in Table 4.4 below. Table 4.4: Roof Assembly U-Factor and Insulation R-value Requirements (ECBC Table 4.3.1) Climate Zone 24-Hour use buildings Hospitals, Hotels, Call Centers etc.
Maximum U-factor of the overall assembly (W/m2K) Composite Hot and Dry Warm and Humid Moderate Cold
U-0.261 U-0.261 U-0.261 U-0.409 U-0.261

Daytime use buildings Other Building Types

Minimum R-value of insulation alone (m2K/W)
R-2.1 R-2.1 R-2.1 R-2.1 R-2.1

Minimum R-value Maximum U-factor of of insulation alone the overall assembly (m2K/W) (W/m2K)
R-3.5 R-3.5 R-3.5 R-2.1 R-3.5 U-0.409 U-0.409 U-0.409 U-0.409 U-0.409

Some recommended practices for proper installation and protection of insulation are provided below:
Insulation

The irst set of mandatory requirements addresses the proper installation and protection of insulation materials. It is recommended that insulation materials be installed according to the manufacturers recommendations and in a manner that will achieve the rated insulation R-value. Compressing the insulation reduces the effective R-value and the thermal performance of the construction assembly.
Substantial Contact

It is recommended that insulation be installed in a permanent manner and in substantial contact with the inside surface of the construction assembly. If the insulation does not entirely ill the cavity, the air gap should be on the outside surface. Maintaining substantial contact is particularly important (and problematic) for batt insulation installed between loor joists. Without proper support, gravity will cause the insulation to fall away from the loor surface, leaving an air gap above the insulation. Air currents will ultimately ind their way to the gap, and when they do, the effectiveness of the insulation will be substantially reduced.

Energy Conservation Building Code (ECBC) User Guide

21

Building Envelope

Insulation Above Suspended Ceilings

It is not good practice to install insulation directly over suspended ceilings with removable ceiling panels. This is because the insulations continuity is likely to be disturbed by maintenance workers. Also, suspended ceilings may not meet the ECBCs iniltration requirements unless they are properly sealed. Compliance with this requirement could have a signiicant impact in some parts of the country, as it is common practice to install insulation over suspended ceilings. Many building codes will consider the space above the ceiling to be an attic and require that it be ventilated to the exterior. If vented to the exterior, air in the attic could be quite cold (or hot) and the impact of the leaky suspended ceiling would be made worse.
Insulation Protection

It is strongly recommended that insulation be protected from sunlight, moisture, landscaping equipment, wind, and other physical damage. Rigid insulation used at the slab perimeter of the building should be covered to prevent damage from gardening or landscaping equipment. Rigid insulation used on the exterior of walls and roofs should be protected by a permanent waterproof membrane or exterior inish. In general, a prudent designer should pay attention to moisture migration in all building construction. Vapor retarders prevent moisture from condensing within walls, roofs, or loors but care should be taken to install them on the correct side (warmer or cooler side) of the walls and roofs to prevent water damage. Water condensation can damage the building structure and can seriously degrade the performance of building insulation and create many other problems such as mold and mildew. The designer should evaluate the thermal and moisture conditions that might contribute to condensation and make sure that vapor retarders are correctly installed to prevent condensation. In addition to correctly installing a vapor retarder, it is important to provide adequate ventilation of spaces where moisture can build up. Figure 4.7 shows some common techniques to insulate different types of rooing systems.

Pre-Fabricated Metal Roofs Showing Thermal Blocking of Purlins

Steel Joist Roof with Insulated Cavities

Metal Framed Ceiling Insulation

Energy Conservation Building Code (ECBC) User Guide

22

Building Envelope

Insulation entirely above deck: Insulation is installed above (a) concrete, (b) wood or (c) metal deck in a continuous manner. (a), (b), and (c) are shown sequentially right to left.

Steel Joist Roof with Continuous Insulation

Figure 4.7: Building Roofs

A. RCC Slab Insulated with Vermiculite B. RCC Slab Insulated with Earthen Pots

Energy Conservation Building Code (ECBC) User Guide

23

Building Envelope

C. RCC Slab Insulated using Foamular Metric

Figure 4.8: Typical Insulation Techniques for RCC Roof Construction

4.3.2

Cool Roofs

Depending on the material and construction, a roof will have different properties that determine how it conducts heat to the inside of the building. Cool roofs are roofs covered with a relective coating that has a high emissivity property that is very effective in relecting the suns energy away from the roof surface. These cool roofs are known to stay 10C to 16C cooler than a normal roof under a hot summer sun; this quality greatly reduces heat gain inside the building and the cooling load that needs to be met by the HVAC system. Box 4-G discusses how solar heat radiation is relected, absorbed and emitted from the roof and how these concepts are used in developing cool roofs.

Box 4-G: Relectance, Absorptance, and Emissivity

The heat transfer process involved in the roof, is similar to the heat transfer that takes in a wall. Heat transfer across the roof is more prominent compared to the wall because of higher incidence of solar radiation. Depending on the properties of the roof material and construction, the roof relects part of the solar radiation back to the environment, and absorbs the other part of the heat in the roof (See Figure 4.9). Finally, portion of the absorbed heat in the roof is emitted as long-wave radiation back to the environment and the remaining part of the absorbed heat is conducted inside of the building. This heat transfer process is governed by the Solar Relectance and Emissivity (Thermal Emittance) properties of the roof material, apart from the thermal conductivity of the materials used in the roof.

Figure 4.9: Heat Transfer Through Roof

Energy Conservation Building Code (ECBC) User Guide

24

Building Envelope

Solar Relectance and Absorptance The solar relectance is the fraction of solar radiation relected by roof. The complement of relectance is absorptance; whatever radiant energy incident on a surface that is not relected is absorbed in the roof. The relectance and absorptance of building materials are usually measured across the solar spectrum, since these are exposed to that range of wavelength. Relectance is measured on a scale of 0 to 1, with 0 being a perfect absorber and 1 being a perfect relector. Absorptance is also rated from 0 to 1, and can be calculated from the relation: Relectance + Absorptance = 1. Emissivity or Thermal Emittance Emissivity (or thermal emittance) of a material (usually written or e) is the ratio of energy radiated by a particular material to energy radiated by a black body at the same temperature. It is a measure of a materials ability to radiate the absorbed energy. A true black body would have an e =1 while any real object would have e <1. Emissivity is a dimensionless quantity (does not have units). In general, the duller and blacker a material is, the closer its emissivity is to 1. The more relective a material is, the lower its emissivity. The emissivity of building material, unlike relectance, is usually measured in the far infrared part of the spectrum. Ideal Exterior Surface An ideal exterior surface coating of a building in hot climate and under indoor cooling would have relectance near 1, and absorptance near zero, and Emissivity near 1 to radiate absorbed heat back to the sky. If designing a cool roof, requirements for minimum solar relectance and initial emittance levels are speciied [ECBC 4.3.1.1]. Roofs with slopes less than 20 shall have an initial solar relectance of no less than 0.70 and an initial emittance no less than 0.75. Solar relectance shall be determined in accordance with ASTM E903-96 and emittance shall be determined in accordance with ASTM E408-71 (RA 1996).

Box 4-H: Cool Roofs

In hot climates, cool roofs (or high emissivity or thermal emittance roof surfaces) are an effective way to reduce solar gains and cut building owners energy costs. Because cool roofs gain less heat than normal roofs, they reduce the need for air conditioning and make buildings more comfortable to the people inside. The light color relects sunlight and heat away from the building, and the high emissivity or thermal emittance allows heat to escape to the atmosphere when the surface becomes heated. Although some surfaces, such as galvanized metal, have a high relectance, they have a low emittance. These surfaces relect heat, but heat that is absorbed cannot escape. Other surfaces, such as dark paint, have a high emittance but a low relectance. These surfaces allow heat to escape, but do a poor job of relecting heat that strikes the surface. Most cool roof materials for low-sloped roofs are white or another light color. For steep-sloped roofs that are often visible from the ground, rooing material manufacturers have developed popular roof colors other than white that will still relect solar radiation or emit the suns energy away from the building. Cool roofs have other beneits in addition to reducing operating absorbed heat costs. For building owners, they can cut maintenance costs and increase the life expectancy of the roof. For society in general, cool roofs can even help to reduce the urban heat island effect and slow down global warming that makes our cities hotter and produces unhealthy air. What is meant by Urban Heat Island effect? An Urban Heat Island is a metropolitan urban area, which is signiicantly warmer than its surroundings. As population centers grow in size, they tend to have a corresponding increase in average temperature. Scientists refer to this phenomenon as the Urban Heat Island Effect. The two main causes of the urban heat island is modiication of the land surface by urban development and waste heat generated by energy usage. One consequence of urban heat islands is the increased energy required for air conditioning and refrigeration in cities that are in comparatively hot climates.

Energy Conservation Building Code (ECBC) User Guide

25

Building Envelope

What types of rooing products are available? Products for low-slope roofs, found on commercial and industrial buildings fall into two categories: single-ply materials and coatings. Single-ply materials are large sheets of pre-made rooing that are mechanically fastened over the existing roof and sealed at the seams. Coatings are applied using rollers, sprays, or brushes, over an existing clean, leak-free roof surface. Products for sloped roofs are currently available in clay, or concrete tiles. These products stay cooler by the use of special pigments that relect the suns infrared heat. In India, lime coats, white tiles grouted with white cement, special paints, etc. are used as cool rooing materials.

4.3.3

Opaque Walls

Opaque walls can meet the prescriptive requirements by either using a construction that has an assembly U-factor lower than the speciied value as shown in ECBC Table 4.2 (reproduced in Table 4.5), or by using insulation with R-value more than the prescribed value. R-value is for the insulation alone and does not include building materials or air ilms. Table 4.5: Opaque Wall Assembly U-Factor and Insulation R-value Requirements (ECBC Table 4.2) Climate Zone Hospitals, Hotels, Call Centers (24-Hour)
Maximum U-factor of the overall assembly (W/m2K)
Composite Hot and Dry Warm and Humid Moderate Cold U-0.440 U-0.440 U-0.440 U-0.440 U-0.369

Other Building Types (Daytime)

Maximum U-factor of the overall assembly (W/m2K)
U-0.440 U-0.440 U-0.440 U-0.440 U-0.352

Minimum R-value of insulation alone (m2K/W)

R-2.10 R-2.10 R-2.10 R-2.10 R-2.20

Minimum R-value of insulation alone (m2K/W)

R-2.10 R-2.10 R-2.10 R-2.10 R-2.35

4.3.4

Vertical Fenestration

The ECBC limits the area of vertical fenestration, under the prescriptive approach, to a maximum of 60% of the gross wall area. The ECBC addresses energy losses through fenestration by specifying the following requirements: maximum U-factor (or thermal transmittance) and maximum SHGC, for the following window to wall ratio (WWR): WWR up to 40% and WWR in the range of more then 40% and up to 60% Vertical fenestration should meet the requirements for maximum area weighted U-factor and maximum area weighted SHGC. The U-factor and SHGC requirements of the rated (labeled) fenestration for two WWR ranges for Code compliance are given in Table 4.3 of ECBC (reproduced in Table 4.6. Table 4.6: Vertical Fenestration U-factor (W/m2K) and SHGC Requirements (ECBC Table 4.3) WWR40%
Climate Composite Hot and Dry Warm and Humid Moderate Cold Maximum U-factor
3.30 3.30 3.30 6.90 3.30

40% <WWR60%
Maximum SHGC
0.20 0.20 0.20 0.30 0.51

Maximum SHGC
0.25 0.25 0.25 0.40 0.51

See Appendix C of ECBC for default values of unrated fenestration values for unrated windows must follow the values given in Table 11.1 of Appendix C of ECBC.
Energy Conservation Building Code (ECBC) User Guide 26

Building Envelope

Table 4.7: Defaults for Unrated Vertical Fenestration (Overall Assembly including Sash and Frame) - Table 11.1 of ECBC
Frame Type Glazing Type

Clear Glass
U-factor (W/m2 K) SHGC
0.82 0.59 0.68

Tinted Glass
VLT
0.76 0.64 0.66

U-Factor (W/m2 K)
7.1 3.4 5.1

SHGC
0.70 0.42 0.50

VLT
0.58 0.39 0.40

All frame types Wood, vinyl, or iberglass frame Metal and other frame type

Single Glazing Double Glazing Double Glazing

7.1 3.3 5.1

Box 4-I: Energy-Eicient Fenestration Products/Assemblies.

Windows are affected by many factors, which in turn affect the comfort and energy performance of buildings. Understanding these factors is critical in designing buildings that meet the needs of building owners and users. Once these factors are identiied, a designer can then apply the appropriate technology to address them. A fenestration product is comprised of three areas: the vision area, the glazing, and the opaque area or the frame. In a window, glazing is generally 90-95% of the total area and therefore the most important part to address for achieving energy eficiency. However, the frame becomes important to optimize the overall energy eficiency of the window. The energy eficiency of a fenestration product is affected by: Films which are applied to improve energy eficiency Low emissivity (low-e) coatings for energy-eficient windows Gas ill used in insulating glass units for energy-eficient windows Insulating glass units for energy-eficient windows Frame designs for energy-eficient windows Reducing the air leakage of windows to improve energy eficiency Number of layers of glass in the fenestration product. The technology for producing energy-eficient windows relies heavily on the development of coatings for glass. A low-e coating allows the visible light to pass through relatively unaffected whole rejecting invisible infrared heat. For example, an emissivity of 0.10 means that 90% of the long heat radiation is relected back. There are a large number of glazing products that are available from different manufacturers complying with the ECBC requirements for fenestrations. Exception to ECBC 4.3.3: The SHGC requirement of a window can be affected by overhangs on a building, which reduce solar gains. The ECBC uses a term called a projection factor to determine how well an overhang shades the buildings glazing. The projection factor is calculated by measuring the distance from the window to the farthest edge of the overhang and dividing that by the distance from the bottom of the window to the lowest point of the overhang demonstrates how to calculate a projection factor. Projection Factor = H (horizontal)/V (vertical) The ECBC provides a modiied SHGC requirement where there are overhangs and/or side ins, which are a permanent part of the building. This may be applied in determining the SHGC for the Proposed Design. An adjusted SHGC, accounting for overhangs and/or sideins, is calculated by multiplying the SHGC of the unshaded fenestration product by a multiplication (M) factor. If this exception is applied, a separate M Factor shall be determined for each orientation and unique shading condition.

Energy Conservation Building Code (ECBC) User Guide

27

Building Envelope

PF= Ratio of overhang projection divided by height from window sill to bottom of overhang (must be permanent) Solar heat gain Coeicient Requirements dependent on: Overhang projection factor M- Factor from Table 4.3.3-2 Orientation And Climate Zone

Without Overhang: SHGC range 0.25-0.51 based on climate zone.

Figure 4.10: Projection Calculation ECBC Table 4.4 provides the values of M-factor for various projection factors. Table 4.8: SHGC M Factor Adjustments for Overhangs and Fins (ECBC Table 4.4) Overhang M Factors for 4 Projection Factors
Project Location

Vertical Fin M Factors for 4 Projection Factors

1.00 +
.52 .60 .56 .50 .58 .50

Overhang +Fin M Factors for 4 Projection Factors

0.25 0.50 0.75 1.00 + 0.49 0.74 0.99
.64 .60 .60 .59 .61 .53 .51 .39 .33 .44 .41 .30 .39 .24 .10 .32 .26 .12 .31 .16 .02 .23 .16 .04

Orientation 0.25 0.50 0.75 1.00 0.25 0.50 0.75 + 0.49 0.74 0.99 0.49 0.74 0.99
N E/W S N E/W S .88 .79 .79 .83 .80 .78 .80 .65 .64 .74 .67 .62 .76 .56 .52 .69 .59 .55 .73 .50 .43 .66 .53 .50 .74 .80 .79 .73 .80 .74 .67 .72 .69 .65 .72 .65 .58 .65 .60 .57 .63 .57

North latitude 15 or greater Less than 15 North latitude

Example 4.2: Prescriptive Requirements for Fenestration

Location : Chandigarh Climate Zone : Composite (Lat: 30 42 N; Long: 76 54 E) Building Type : Daytime Use Building Roof Area : 568 m2 Roof Insulation : Rigid Board 1 inch R = 2.1 m2K/W Wall Area : 1130 m2 Wall Insulation : Rigid Board 1 inch R = 1.41 m2K/W Total Fenestration Area: 508 m2 Window to Wall ratio : 508/1130 = 45% East/West and South facing windows are all 1.82880m 0.91440m with a 0.45720 m overhang and represent 75% of the glazing on the building. Projection Factor : H/V = 0.45720/1.82880 = 0.25 M factor : 0.79 (From ECBC Table 4.4, Projection Factor=0.25, E/W and S orientation for north latitude 15 or greater) East/West and South facing glazing : 508 0.75 = 381 m2 East/West and South facing Fenestration : SHGC 0.20; U factor 3.30 East/West and South Facing Fenestration: Skylight Area 10.8 m2

Energy Conservation Building Code (ECBC) User Guide

28

Building Envelope

Q: Does my building envelope comply Prescriptively with the ECBC? A: To utilize the prescriptive requirements of ECBC, vertical fenestration is limited to 60% of the gross wall area, so this building is allowed under this method. ECBC Table 4.3 limits the SHGC value to a maximum of 0.20 for composite climate zone, however an exception exists by use of an overhang. ECBC 4.3.3 allows for an M Factor, or multiplier. In this case the M is 0.79. Multiplying M times the SHGC [0.7900 0.20=0.1580] and thus complies with ECBC Table 4.3. Exception to SHGC Requirements in 4.3.3: Vertical Fenestration areas located more than 2.2 m (7 ft) above the level of the loor are exempt from the SHGC requirement in Table 4.3 if the following conditions are complied with: a. Total Effective Aperture: The total Effective Aperture for the elevation is less than 0.25, including all fenestration areas greater than 1.0 m (3 ft) above the loor level b. An interior light shelf is provided at the bottom of this fenestration area, with an interior projection factor not less than: i. 1.0 for E-W, SE, SW, NE, and NW orientations ii. 0.5 for S orientation, and iii. 0.35 for N orientation when latitude is < 23

4.3.4.1 Minimum Visible Transmission of Glazing for Vertical Fenestration.

ECBC encourages the use of daylighting features in buildings. Box 4-J discusses how glazing affect the daylighting. It also explains the concept of Visual Light Transmittance (VLT) and Effective Aperture (EA) of Glazing. As per the Code: Vertical fenestration product shall have the minimum Visual Light Transmittance (VLT), deined as function of Window Wall Ratio (WWR), where Effective Aperture > 0.1, equal to or greater than the Minimum VLT requirements of Table 4.5 (of ECBC). Table 4.9: Minimum VLT Requirements (ECBC Table 4.5) Window Wall Ratio
0 - 0.3 0.31-0.4 0.41-0.5 0.51-0.6

Minimum VLT
0.27 0.20 0.16 0.13

Box 4-J: Daylighting, Visual Light Transmittance and Efective Aperture

Visual Light Transmittance (also known as Visual Transmittance VT) is deined as the ratio of light that passes through the glazing to the light passing through perfectly transmitting glazing. In other words it also refers to the fraction of visible light transmitted through the glazing. VLT is concerned with the visible portion of the solar spectrum (See Figure 4.11) as opposed to SHGC, which takes into account the entire solar radiation. VLT affects energy consumption in building by providing daylight that creates the opportunity to reduce electric lighting and its associated cooling loads. Glazing with low SHGC generally has a low VLT; however, if the VLT is too low, the outside view from inside the building will be impaired. With lower VLT, the daylighting in the interior may also reduce to a level that may require supplemental electrical lighting for some occupants functions, or to make the environment productive and enjoyable to the occupants. Thus buildings with lower window to wall ratios (WWR), may need higher VLT.

Energy Conservation Building Code (ECBC) User Guide

29

Building Envelope

Figure 4.11: Illustration to show U-factor, SHGC, and VLT Effective Aperture of Glazing In simple terms, as the area of an aperture/opening in the building envelope increases, the amount of daylight received in the building space also increases. However the glazing material within that aperture can effectively reduce the amount of visible light that enters the space. Therefore, aperture size alone is not an effective determinant to measure illumination levels. If the glazing in an opening is a perfectly transparent material the effective aperture size would be equal to the area of the opening (because the visible transmittance of the glazing would be one). If however, the glazing has a VLT of 0.5, the opening will transmit only half of the light striking it, and the effective aperture will be half of the actual size of the opening. The Effective Aperture (EA) or light admitting potential of a glazing system is determined by multiplying the Visible Light Transmittance of the glazing by the window-to-wall ratio of the building. The window to wall ratio is the ratio of the net window area to the exterior wall area. Effective Aperture: Visible Light Transmittance Window-to-Wall Ratio (WWR). = VLT WWR. Example: Two cases with WWR =0.4, and WWR = 0.6 are discussed below.
Case 1 Case 2

WWR = 0.4 VLT = 0.26 EA = 0.104 (EA > 0.1) Glazing complies with ECBC

WWR = 0.6 VLT = 0.15 EA = 0.09 (EA < 0.1) Glazing does not comply with ECBC

4.3.5

Skylights

A skylight is a fenestration surface having a slope of less than 60 degrees from the horizontal plane. Other fenestration, even if mounted on the roof of a building, is considered vertical fenestration. Skylights can be installed into a roof system either lush-mounted or curb-mounted (including site built). In order to create a positive water low around them, skylights are often mounted on curbs set above the roof plane. However, these curbs, rising 6 to 12 inches (15 to 30 centimeters) above the roof, create additional heat loss surfaces right where the warmest air of the building tends to collect. Portions of roof that serve as curbs that mount the skylight above the level of the roof (See below) are part of the opaque building envelope.

Energy Conservation Building Code (ECBC) User Guide

30

Building Envelope

Figure 4.12: Skylight Installations As per the Code: Skylights shall comply with the maximum U-factor and maximum SHGC requirements of Table 4.6. Skylight area is limited to a maximum of 5% of the gross roof area for the prescriptive requirement. Table 4.10: Skylight U-Factor and SHGC Requirements (ECBC Table 4.6) Maximum U-factor
Climate Composite Hot and Dry Warm and Humid Moderate Cold With Curb
11.24 11.24 11.24 11.24 11.24

Maximum SHGC
w/o Curb
7.71 7.71 7.71 7.71 7.71

0-2% SRR
0.40 0.40 0.40 0.61 0.61

2.1-5% SRR
0.25 0.25 0.25 0.4 0.4

SRR: Skylight roof ratio which is the ratio of the total skylight area of the roof, measured to the outside of

the frame, to the gross exterior roof. See 11.2.2 for typical complying skylight constructions.

Example 4.3: Prescriptive Requirements for Skylights

Location Climate Zone Building Type Roof Area Roof Insulation Wall Area Wall Insulation Fenestration Area : Chennai : Warm-Humid : Daytime Use Building : 1,863 m2 : Rigid Board 1 inch R= 2.1 m2K/W : 3,706 m2 : Rigid Board 1 inch R= 1.41 m2K/W : 487 m2

Window to Wall ratio : 487/3706 = 13% SHGC : 0.20 Ufactor : 3.30 Skylight Area : 112 m2 Skylight to Roof Area : 112/1863= 6% Q: Does my building envelope comply with the ECBC using the prescriptive path? A: No, this building does not comply because the prescriptive approach limits skylights area to a maximum of 5% of the roof area. This building would need to comply under the envelope trade off option of the Whole Building Approach. As with windows, the skylight-roof ratio must be calculated separately for each space category. The criteria for each space category are determined from its own skylight-roof ratio, not the skylight-roof ratio for the whole building.

Energy Conservation Building Code (ECBC) User Guide

31

Building Envelope

Box 4-K: Glazing Selection for ECBC Compliance

What is the most important feature that a building professional should look for regarding windows, doors, and skylights? The SHGC and U-factor ratings are the most important items to verify during inspections. Building professionals should verify that the ratings of the installed windows, doors, and skylights meet or exceed the ratings speciied on the plans. It is also important to verify that the same window area has been installed as the area shown on the plans and that the glass orientation on the plans and building are consistent. What is Solar Heat Gain Coeficient? The Solar Heat Gain Coeficient is a measure of the percentage of heat from the sun that gets through a window or other fenestration product. The SHGC is expressed as a number between 0 and 1. The lower a windows SHGC, the less solar heat it transmits to the interior of the building. SHGC can also refer to shading so the lower the SHGC the more effective the product is at shading the heat gain from entering the interior. What is low-e glass? Low-e stands for low-emissivity and refers to a special coating that reduces the heat transfer of a window assembly. Low-e coated products that reduce solar heat gain can be produced by adding a metallic coating either while the glass is in a molten state or by applying to the glass after it has cooled to a solid state. Low-e glass is readily available from all the glass and window manufacturers. The coatings typically add about 10% to the cost of a window but costs vary by product type, by manufacturer, by retailer and by location. What is spectrally selective glass? The sun emits visible solar radiation in the form of light and infrared radiation that cannot be seen, but causes heat. Spectrally selective glass transmits a high proportion of the visible solar radiation, but screens out radiant heat from the sun signiicantly reducing the need to cool a buildings interior. Spectrally selective glass is used to describe low-e coated glass that lowers the SHGC. How can I be sure I have spectrally selective glass? The SHGC rating for the product is the key to determining whether you have glass with a spectrally selective coating. In general, windows with a spectrally selective low-e coating will have SHGC ratings of 0.40 or lower.

4.4 Building Envelope Trade-Of Option

This is a systems-based approach, where the thermal performance of individual envelope components can be reduced if compensated by higher eficiency in other building components (i.e., using higher wall insulation could allow for a less stringent U-factor requirement for windows, or vice versa.) These trade-offs typically occur within major building systems roofs, walls, fenestration, overhangs etc. This method offers the designer more lexibility than strictly following the prescribed values for individual elements. The thermal performance of one envelope component such as the roof can fail to meet the prescriptive requirements as long as other components perform better than what is required. Trade-offs are permitted only between building envelope components. It is not possible, for instance, to make trade-offs against improvements in the lighting or HVAC systems. However, this makes using the envelope trade-off option more complicated than the prescriptive method. It is necessary to calculate the surface area of each exterior and semiexterior surface; all areas must also be calculated separately for each orientation. The equations used for calculating envelope performance factor under envelope trade-offs are documented in ECBC 12 Appendix D.

Energy Conservation Building Code (ECBC) User Guide

32

Heating, Ventilation and Air Conditioning

5. Heating, Ventilation and Air Conditioning

5.1 General
eating, Ventilation and Air Conditioning (HVAC) refers to the equipment, distribution systems, and terminals that provide, either collectively or individually, the heating, ventilation, or air-conditioning requirement to a building or a portion of building. The HVAC system accounts for a signiicant portion of a commercial buildings energy use. HVAC energy use in a commercial building can increase/decrease signiicantly depending on how eficiently the combination of air side systems and central plant operates. Proven technologies and design concepts can be used to build energy eficiencies in the system and generate signiicant energy and cost savings. HVAC systems also affect the health, comfort, and productivity of occupants. Issues like user discomfort, improper ventilation, lack of air movement and poor indoor air quality, and poor acoustic design are linked to HVAC system design and operation and can be improved. In many existing buildings, envelope upgrades are often necessary to improve comfort and energy eficiency, through improvements such as reducing envelope leakage. Generally, upgrading an existing building envelope is expensive. Other strategies such as central plant, airside or control system upgrade may be necessary to improve occupant comfort and energy eficiency. The best HVAC design considers all the interrelated building systems while addressing indoor air quality, thermal comfort, energy consumption, and environmental beneits. Optimizing both the design and the beneits requires that the architect and mechanical system designer address these issues early in the schematic design phase and continually revise subsequent decisions throughout the remaining design process. It is also essential that a process be implemented to monitor proper installation and operation of the HVAC system throughout construction. An effective commissioning plan for each of the systems at full load and part load including controls calibration and commissioning is essential to the optimal performance of the building. General concepts of HVAC systems are discussed in more details in Box 5-A and Box 5-B.

Box 5-A: Air Conditioning System Basics

Basic components of the system include a compressor, condenser (air-cooled or water cooled), evaporator and an expansion device., similar to that of a domestic refrigerator.
C
Discharge Line Condenser Compressor

Liquid Line Expansion Device

A
Suction Line

D
Evaporater

Room air is drawn across an indoor coil called the evaporator that cools and dehumidiies the air during the cooling cycle. The condenser condenses the refrigerant and transforms the high pressure vapor into high pressure liquid. Heat is rejected via air drawn across the condenser coils using fans (air-cooled condenser) or using a shell and tube heat exchanger in conjunction with a condenser water reticulation system and cooling towers (water cooled condenser). The expansion device transforms the high pressure high temperature liquid refrigerant to low pressure low temperature mixture of refrigerant liquid and vapor. This mixture fully evaporates in the evaporator absorbing the heat from the water (cooling the water in a chilled water system) or cooling the air drawn across the coil (direct expansion system). The compressor then raises the pressure and temperature of the refrigerant and the cycle continues on.

Energy Conservation Building Code (ECBC) User Guide

33

Heating, Ventilation and Air Conditioning

Box 5-B: Heating Systems

Heating system types can be classiied fairly well by the heating equipment type. The heating equipment used in buildings includes boilers (oil and gas), furnaces (oil, gas, and electric), heat pumps, and space heaters. Boiler-based heating systems have steam and/or water piping to distribute heat. Boilers can be self-contained units, or they can be packaged units which are factory-built systems, disassembled for shipment, and reassembled at the site. The heated water may serve preheat coils in air handling units; reheat coils, and local radiators. Systems that circulate water or a luid are called hydronic systems. Heating water may also be used for heating of service water and other process needs, depending on the building type. Some central systems have steam boilers rather than hot water boilers because of the need for steam for conditioning needs (humidiiers in air-handling units) or process needs (sterilizers in hospitals, direct-injection heating in laundries and dishwashers, etc.). The remaining heating systems include heat pumps and space heaters that heat directly and require little or no distribution.

5.2 Mandatory Requirements

The Code contains mandatory requirements for the following elements of the HVAC system: Natural Ventilation Equipment Eficiency Controls Piping and Ductwork System Balancing. Condensers Economizers Hydronic Systems

5.2.1

Natural Ventilation

As per the Code: Natural ventilation (of buildings) shall comply with the design guidelines provided for natural ventilation in the National Building Code of India 2005,(NBC, 2005) Part 8, 5.4.3 and 5.7.1 These guidelines from NBC, 2005 have been reproduced below in Box 5-C, keeping in view the philosophy behind this Guide to include ECBC-referenced material in the Guide. However, the exact relevance of these general guidelines in the design of commercial buildings need to be critically examined.

Box 5-C: Design Guidelines for Natural Ventilation

By Wind Action i. Building need not necessarily be oriented perpendicular to the prevailing outdoor wind; it may be oriented at any convenient angle between 0 and 30 without losing any beneicial aspect of the breeze. If the prevailing wind is from east or west, building may be oriented at 45 to the incident wind so as to diminish the solar heat without much reduction in air motion indoors. ii. Inlet openings in the buildings should be well distributed and should be located on the windward side at a low level, and outlet openings should be located on the leeward side. Inlet and outlet openings at high levels may only clear the top air at that level without producing air movement at the level of occupancy. iii. Maximum air movement at a particular plane is achieved by keeping the sill height of the opening at 85% of the critical height (such as head level) for the following recommended levels of occupancy:
1. For sitting on chair 0.75 m 2. For sitting on bed 0.60 m

Energy Conservation Building Code (ECBC) User Guide

34

Heating, Ventilation and Air Conditioning

3. For sitting on loor 0.40 m

iv. v.

vi. vii.

viii.

ix. x. xi.

xii.

xiii. xiv. xv. xvi. xvii.

xviii. xix. xx.

Inlet openings should not, as far as possible, be obstructed by adjoining buildings, trees, sign boards or other obstructions or by partitions inside in the path of air low. In rooms of normal size having identical windows on opposite walls the average indoor air speed increases rapidly by increasing the width of the window up to two-thirds of the wall width; beyond that the increase is in much smaller proportion than the increase of the window width. The air motion in the working zone is maximum when window height is 1.1 m. Further increase in window height promotes air motion at higher level of window, but does not contribute additional beneits as regards air motion in the occupancy zones in buildings. Greatest low per unit area of openings is obtained by using inlet and outlet openings of nearby equal areas at the same level. For a total area of openings (inlet and outlet) of 20% to 30% of loor area, the average indoor wind velocity is around 30% of outdoor velocity. Further increase in window size increases the available velocity but not in the same proportion. In fact, even under most favorable conditions the maximum average indoor wind speed does not exceed 40% of outdoor velocity. Where the direction of wind is quite constant and dependable, the size of the inlet should be kept within 30 to 50% of the total area of openings and the building should be oriented perpendicular to the incident wind. Where direction of the wind is quite variable, the openings may be arranged so that as far as possible there is approximately equal area on all sides. Thus no matter what the wind direction is, there would be some openings directly exposed to wind pressure and others to air suction and effective air movement through the building would be assured. Windows of living rooms should open directly to an open space. In places where building sites are restricted, open space may have to be created in the buildings by providing adequate courtyards. In the case of rooms with only one wall exposed to outside, provision of two windows on that wall is preferred to that of a single window. Windows located diagonally opposite to each other with the windward window near the upstream comer give better performance than other window arrangements for most of the building orientations. Horizontal louvers, that is a sunshade, atop a window delects the incident wind upward and reduces air motion in the zone of occupancy. A horizontal slot between the wall and horizontal louver prevents upward delection of air in the interior of rooms. Provision of inverted L type (r) louver increases the room air motion provided that the vertical projection does not obstruct the incident wind. Provision of horizontal sashes inclined at an angle of 45 in appropriate direction helps to promote the indoor air motion. Sashes projecting outward are more effective than projecting inward. Air motion at working plane 0.4 m above the loor can be enhanced by 30% using a pelmet type wind delector. Roof overhangs help by promoting air motion in the working zone inside buildings. Verandah open on three sides is to be preferred since it causes an increase in the room air motion for most of the orientations of the building with respect to the outdoor wind. A partition placed parallel to the incident wind has little inluence on the pattern of the air low, but when located perpendicular to the main low, the same partition creates a wind shadow. Provision of a partition with spacing of 0.3 m underneath helps by augmenting air motion near loor level in the leeward compartment of wide span buildings. Air motion in a building unit having windows tangential to the incident wind is accelerated when unit is located at end-on position on downstream side. Air motion in two wings oriented parallel to the prevailing breeze is promoted by connecting them with a block on downstream side. Air motion in a building is not affected by constructing another building of equal or smaller height on the leeward side; but it is slightly reduced if the leeward building is taller than the windward block.

Energy Conservation Building Code (ECBC) User Guide

35

Heating, Ventilation and Air Conditioning

xxi. Air motion in a shielded building is less than that in an unobstructed building. To minimize the shielding effect, the distances between two rows should be 8H for semi-detached houses and 10H for long rows houses. However, for smaller spacing the shielding effect is also diminished by raising the height of the shielded building. xxii. Hedges and shrubs delect the air away from the inlet openings and cause a reduction in indoor air motion. These elements should not be planted at a distance of about 8m from the building because the induced air motion is reduced to minimum in that case. However, air motion in the leeward part of the building can be enhanced by planting a low hedge at a distance of 2m from the building. xxiii. Trees with large foliage mass having trunk bare of branches up to the top level of window, delect the outdoor wind downwards and promotes air motion in the leeward portion of buildings. xxiv. Ventilation conditions indoors can be ameliorated by constructing buildings on earth mound having a slant surface with a slope of 10 on the upstream side. xxv. In case of industrial buildings the window height should be about 1.6m and the width about twothirds of wall width. These should be located at a height of 1.1m above the loor. In addition, openings around 0.9m high should be provided over two-thirds of the length of the glazed area in the roof lights. xxvi. Height of industrial buildings, although determined by the requirements of industrial processes involved, generally kept large enough to protect the workers against hot stagnant air below the ceiling as also to dilute the concentration of contaminant inside. However, if high level openings in roof or walls are provided, building height can be reduced to 4m without in any way impairing the ventilation performance. By Stack Effect Natural ventilation by stack effect occurs when air inside a building is at a different temperature than air outside. Thus, in heated buildings or in buildings wherein hot processes are carried out and in ordinary buildings during summer nights and during premonsoon periods, when the inside temperature is higher than that of outside, cool outside air will tend to enter through openings at low level and warm air will tend to leave through openings at high level. It would, therefore, be advantageous to provide ventilators as close to ceilings as possible. Ventilators can also be provided in roofs as, for example, cowl, ventpipe, covered roof and ridge vent. Energy Conservation in Ventilation System Maximum possible use should be made of wind-induced natural ventilation. This may be accomplished by following the design guidelines i. Adequate number of circulating fans should be installed to serve all interior working areas during the summer months in the hot dry and warm humid regions to provide necessary air movement at times when ventilation due to wind action alone does not afford suficient relief. ii. The capacity of a ceiling fan to meet the requirement of a room with the longer dimension D meters should be about 55D m3/min. iii. The height of fan blades above the loor should be (3H + W)/4, where H is the height of the room, and W is the height of the work plane. iv. The minimum distance between fan blades and the ceiling should be about 0.3 meters. v. Electronic regulators should be used instead of resistance type regulators for controlling the speed of fans. vi. When actual ventilated zone does not cover the entire room area, then optimum size of ceiling fan should be chosen based on the actual usable area of room, rather than the total loor area of the room. Thus smaller size of fan can be employed and energy saving could be achieved. vii. Power consumption by larger fans is obviously higher, but their power consumption per square meter of loor area is less and service value higher. Evidently, improper use of fans irrespective of the rooms dimensions is likely to result in higher power consumption. From the point of view of energy consumption, the number of fans and the optimum sizes for rooms of different dimensions are given in the following table:

Energy Conservation Building Code (ECBC) User Guide

36

Heating, Ventilation and Air Conditioning

Table 5.1: Optimum Size/Number of Fans for Rooms of Diferent Sizes

Room Width
m (1)
3 4 5 6 7 8 9 10 11 12 13 14

Room Length
4m (2)
1200/1 1200/1 1400/1 1200/2 1200/2 1200/2 1400/2 1400/2 1500/2 1200/3 1400/3 1400/3

5m (3)
1400/1 1400/1 1400/1 1400/2 1400/2 1400/2 1400/2 1400/2 1500/2 1400/3 1400/3 1400/3

6m (4)
1500/1 1200/2 1400/2 900/4 1050/4 1200/4 1400/4 1400/4 1500/4 1200/6 1200/6 1400/6

7m (5)
1050/2 1200/2 1400/2 1050/4 1050/4 1200/4 1400/4 1400/4 1500/4 1200/6 1200/6 1400/6

8m (6)
1200/2 1200/2 1400/2 1200/4 1200/4 1200/4 1400/4 1400/4 1500/4 1200/6 1200/6 1400/6

9m (7)
1400/2 1400/2 1400/2 1400/4 1400/4 1400/4 1400/4 1400/4 1500/4 1400/6 1400/6 1400/6

10m (8)
1400/2 1400/2 1400/2 1400/4 1400/4 1400/4 1400/4 1400/4 1500/4 1400/6 1400/6 1400/6

11m (9)
1400/2 1500/2 1500/2 1500/4 1500/4 1500/4 1500/4 1500/4 1500/4 1500/6 1500/6 1500/6

12m (10)
1200/3 1200/3 1400/3 1200/6 1200/6 1200/6 1400/6 1400/6 1500/6 1200n 1400/9 1400/9

14m (11)
1400/3 1400/3 1400/3 1400/6 1400/6 1400/6 1400/6 1400/6 1500/6 1400/9 1400/9 1400/9

16m (12)
1400/3 1500/3 1 500/3 1 500/6 1 500/6 1 500/6 1500/6 1 500/6 1 500/6 1400/9 1 500/9 1500/9

Source: National Building Code of India 2005. For data on outdoor wind speeds at a place, reference may be made to The Climatic Data Handbook prepared by Central Building Research Institute, Roorkee, 1999. Box 5-D provides additional information in naturally ventilated spaces for tropical countries.

Box 5-D: Optional Method for Determining Acceptable Thermal Conditions in Naturally Conditioned Spaces Based on Field Experiments Conducted in Tropical Countries
The adaptive model of thermal comfort is derived from a global database of 21,000 measurements taken primarily in ofice buildings in the tropical climate. The allowable operative temperature limits may not be extrapolated to the outdoor temperature above and below the end points of the curves in this igure. If the mean monthly outdoor temperature is less than 10C or greater than 33.5C, this option may not be used. Occupant-controlled naturally conditioned spaces are those spaces where the thermal conditions of the space are regulated primarily by the occupants through opening and closing of windows. Field experiments have shown that occupants thermal responses in such spaces depend in part on the outdoor climate and may differ from thermal responses in buildings with centralized HVAC systems primarily because of the different thermal experiences, changes in clothing, availability of control, and shifts in occupant expectations. This optional method is intended for such spaces. In order for this optional method to apply, the space must be equipped with operable windows that open to the outdoor and that can be readily opened and adjusted by the occupants of the space. Mechanical ventilation with unconditioned air may be utilized, but opening and closing of windows must be the primary means of regulating the thermal conditions in the space. The space may be provided with a heating system, but this optional method does not apply when a heating system is in operation. It applies only to spaces where the occupants are engaged in near sedentary physical activities, with metabolic rates ranging from 1.0 met to 1.3 met1. This optional method applies only to spaces where the occupants may freely adapt their clothing to the indoor and/or outdoor thermal conditions. Limits on Temperature Drifts and Ramps
Time Period Maximum Operative Temperature Change Allowed
0.25h 1.1 C (2.0F) 0.5h 1.7C (3.0F) 1h 2.2C (4.0F) 2h 2.8C (5.0F) 4h 3.3C (6.0F)

Energy Conservation Building Code (ECBC) User Guide

37

Heating, Ventilation and Air Conditioning

Figure 5.1: Acceptable operative temperature ranges for naturally conditioned spaces. Allowable indoor operative temperature for spaces that meet these criteria may be determined from the igure above. This igure includes two sets of operative temperature limits one for 80% acceptability and one for 90% acceptability. The 90% acceptability limits may be used when a higher standard of thermal comfort is desired.
1 1met=

58W/m2 : for typical ofice activity, one person is likely to produce 100- 125 watts of heat.

Source: ASHRAE 55, 2004.

5.2.2

Minimum Equipment Eiciencies

Minimum equipment eficiencies are required to be met for all HVAC equipment. These include chillers, unitary air conditioner, split air conditioner, packaged air conditioner, and boilers. Box 5-E and Box 5-F provide basic information and an overview of air conditioning systems. Box 5-G provides more information on Chillers.

Box 5-E: Type of Air-Conditioning Systems

There are primarily two main types of air conditioning systems: 1. A direct expansion or DX type system in the form of room air conditioners, split system air conditioners and packaged air conditioners. Heat exchange takes place directly from the refrigerant within the copper tubes to the air being drawn across the inned coil by an evaporator fan. The DX type systems offer localized solutions for a buildings heating and cooling needs. These systems are typically appropriate for smaller (single-zone) buildings. 2. Central plant system uses chilled water recirculation. Compared to a DX systems, a central plant HVAC will be able to provide better thermal comfort and lexibility.
Direct Expansion Systems or DX Systems

Unitary air conditioners: These are normally used for cooling individual rooms and provide cooling only when needed. Room air conditioners house all the components of an air conditioning system discussed above in one casing. Their eficiency is generally lower than that of central plant systems. Split-system air conditioning systems: This consists of an outdoor metal cabinet that contains the condenser and compressor, and an indoor cabinet that contains the evaporator. In many split-system air conditioners, this indoor cabinet also contains a furnace or the indoor part of a heat pump. Packaged air conditioners: In a packaged air conditioner, the evaporator, condenser, and compressor are all located in one cabinet, which usually is placed on a roof or on a concrete slab adjacent to the building. This type of air conditioner is typical in small commercial buildings and also in residential buildings. Air supply and return ducts come from indoors through the buildings exterior wall or roof to connect with the packaged air conditioner, which is usually located outdoors. Packaged air conditioners often include electric heating coils or a natural gas furnace. This combination of air conditioner and central heater eliminates the need for a separate furnace indoors.
Energy Conservation Building Code (ECBC) User Guide 38

Heating, Ventilation and Air Conditioning

Central Plant Systems

Central plant air conditioning systems: In central air-conditioning systems, chilled water is generated via a central chilled water plant. The chilled water is distributed to air-handling units or fan-coil units via a chilled water reticulation system consisting of chilled water pipes, valves, ittings, and pumps. The chillers used in central chilled water plants include air-cooled chillers as well as water-cooled chiller systems that work in conjunction with cooling towers for heat rejection. Box 5-F provides an overview of the differences between DX and Central HVAC systems. It should help in selecting appropriate system for the building.

Box 5-F: Overview of DX and Central Plant HVAC Systems

Central Chilled Water Systems Building Space Will require separate building space to house the chillers, Requirements boilers, pumps, AHUs, distribution networks and control
panels. In addition, space is required outdoors for condensing unit for air-cooled machines and cooling tower for water-cooled machines. The building structure should be designed to take the weight of equipment. Suitable vibration control must be considered and adequate load bearing beams and columns must be available for lifting and shifting of such equipment.

Direct Expansion or DX Systems

No separate plant room space is required as the refrigeration package is integral to the package unit/condensing unit which is generally located outdoors. Evaporator units are generally located indoors. The local systems are smaller in size and are less bulky.

Aesthetics Zoning

Central systems are generally designed as concealed systems and the visible distribution grilles etc. can be easily blended with the aesthetics. Central HVAC system may serve multiple thermal zones and have their major components located outside the zone(s) being served, usually in some convenient central location. This system can provide better lexibility in terms of zoning.

The appearance of local units can be unappealing and may not necessarily blend well with the aesthetics. A local HVAC system typically serves a single thermal zone and has its major components located within the zone itself or directly adjacent to the zone. Multiple units are required for multiple zones. This system is less lexible to zoning requirements.

Air Quality

The quality of air conditioning is comparatively superior, The air quality is not comparable to central with better control over temperature, relative humidity, air systems. These systems typically cannot provide iltration, and air distribution. close humidity control or high eficiency iltration. Best suited for applications demanding close control of temperature, humidity, and cleanliness and can be customized The compact systems, being standard factory as per the design conditions. items, typically cannot be modiied to suit the required design conditions all the times. Central HVAC systems will require a control point for each thermal zone. The controls are ield wired and are integrated to a central control panel. The controls are complex and depend on the type of system. Constant air volume (CAV) systems alter the temperature while keeping the constant air delivery. CAV systems serving multiple zones rely on reheat coils to control the delivered cooling. This incurs a lot of energy wastage due to simultaneous cooling and heating. Local units are off-shelf items complete with integrated controls. They usually have a single control point which is typically only a thermostat.

Controls

The room-by-room or zone control minimizes over cooling typical of central air-conditioning systems. With the zone-control ability of the compact systems, only occupied spaces are maintained at a comfort level, and conditioning for the rest of the building is turned down or Space temperature control can also be achieved by applying shut off. a variable air volume (VAV) system, which primarily alters the air delivery rates. The VAV system may or may not have It should be noted that some DX systems have a reheat coil, which provides additional heat when the space limited capacity control and have limited capability does not need to be cooled or needs less cooling than would to reduce airlow during low load situations. be delivered by supply air at the terminal boxs minimum air Hence, there is a limitation in saving fan energy quantity setting. in DX systems with some types of DX systems only having on/off control for the compressors Proper zoning using face zoned AHUs working in that can result in considerable hunting and space conjunction with downstream VAV boxes will provide temperature luctuation. energy-eficient cooling and eliminate the need of reheat.

Energy Conservation Building Code (ECBC) User Guide

39

Heating, Ventilation and Air Conditioning

Eficiency

Central systems usually operate under part load conditions, In a building where a large number of spaces and localized areas cannot be isolated for complete shut may be unoccupied at any given time, such as a down under any condition. dormitory or a motel, local systems may be totally shut off in the unused spaces, thus providing In a central system, the individual control option is not huge energy saving potential. always available. If individual control is desired, the system shall be designed as variable air volume system with localized As a self-contained system, a local HVAC system may provide greater occupant comfort through thermostats. totally individualized control options -- if one Central systems designed for VAV system is based on block room needs heating while an adjacent one needs load calculations, as the VAV units allow the system to cooling, two local systems can respond without borrow air from areas with low load. By incorporating VAVs conlict with variable speed drive on air handling units, it is possible As the compact systems are small, they are to achieve excellent savings in power. designed for full peak load and the standard Proper zoning as mentioned earlier can avoid conlicting rooftop or package units are not typically demands for heating and cooling. available with variable speed option. This type of system therefore has very limited potential to operate eficiently during part load situations. The availability of VRF system is changing this. Central plant systems provide an excellent means to contain all refrigerant within the chiller housing and plant room. It is possible to detect any minor leaks within the localized plant room and take remedial action to arrest the leak. Unlike central systems, DX systems pose a greater risk of refrigerant leaks to the atmosphere. With DX systems installed in several localized areas it may be very dificult or impossible to detect these leaks, especially in split systems with long pipe runs using high pressure refrigerant.

Refrigerant Containment

Operations and Maintenance (O&M)

Large central systems can have a life useful life of up to 25 Local systems can have a useful life of up to 15 years. years. Central systems allow major equipment components to be Local systems maintenance may often be kept isolated in a mechanical room. Grouping and isolating relatively simple but maintenance may have to key operating components allows maintenance to occur with occur directly in occupied spaces. limited disruption to building functions. The initial purchasing and installation cost of a central air conditioning system is much higher than a local system. These systems can offer higher system eficiencies (full load and part load) and thus, can pay pack the elevated initial costs through reduced costs of operations within a few years. Extra cost beneits can be achieved due to the potential for energy eficiency measures like thermal heat recovery, economizers, energy storage systems and etc. Packaged and split units have much lower irst costs than a central system. The operating costs of unitary systems is usually higher due to lower eficiency ratings and lower part load performance values The potential for adoption of high-tech energy eficiency measures is very limited

Cost

Source: A. Bhatia, Course Content (PDH 149), HVAC Design Aspects: Choosing A Right System-Central V/s Compact Systems. http://www.pdhcenter.com/Heating System Types, and Team Catalyst The Code refers to various types of chillers; Box 5-G gives a brief description of the chillers.

Box 5-G: Chiller

What is a Chiller? A chiller is essentially a packaged vapor compression cooling machine. The chiller rejects heat either to condenser water (in the case of a water-cooled chiller) or to ambient air (in the case of an air-cooled chiller). Water-cooled chillers incorporate the use of cooling towers, which improve heat rejection more eficiently at the condenser than air-cooled chillers. For a water-cooled chiller, the cooling tower rejects heat to the environment through direct heat exchange between the condenser water and cooling air. For an air-cooled chiller, condenser fans move air through a condenser coil. As heat loads increase, water-cooled chillers are more energy-eficient than air-cooled chillers. A typical chiller is rated between 15 to 1000 tons (53 to 3,500 kW) in cooling power.

Energy Conservation Building Code (ECBC) User Guide

40

Heating, Ventilation and Air Conditioning

What are the different types of chillers? Chillers are classiied according to compressor type. Electric chillers for commercial comfort cooling have centrifugal, screw, scroll, or reciprocating compressors. Centrifugal and screw chillers have one or two compressors. Scroll and reciprocating chillers are built with multiple, smaller compressors. Centrifugal chillers are the quiet, eficient, and reliable workhorses of comfort cooling. Although centrifugal chillers are available as small as 70 tons, most are 300 tons or larger. Screw chillers are up to 40% smaller and lighter than centrifugal chillers, so are becoming popular as replacement chillers. Scroll compressors are rotary positive-displacement machines, also fairly new to the comfort cooling market. These small compressors are eficient, quiet, and reliable. Scroll compressors are made in sizes of 1.5 to 15 tons. The energy eficiency of cooling and heating systems in terms of Coeficient of Performance (COP), Energy Eficiency Ratio (EER) and Integrated Part-Load Value as speciied by the Code are presented in Box 5-H

Box 5-H: Energy Eiciency Terms

Coeficient of Performance (COP) Cooling The ratio of the rate of heat removal to the rate of energy input, in consistent units, for a complete refrigerating system or some speciic portion of that system under designated operating conditions Coeficient of Performance (COP) Heating The ratio of the rate of heat delivered to the rate of energy input, in consistent units, for a complete heat pump system, including the compressor and, if applicable, auxiliary heat, under designated operating conditions Energy Eficiency Ratio (EER) The ratio of net cooling capacity in BTU/hr to total rate of electric input in watts under designated operating conditions. Integrated Part-Load Value (IPLV) A single number igure of merit based on part-load EER, COP, or KW/ton expressing part-load eficiency for air-conditioning and heat pump equipment on the basis of weighted operation at various load capacities for the equipment. As per the Code: Cooling equipment shall meet or exceed the minimum eficiency requirements presented in Table 5.2. Heating and cooling equipment not listed here shall comply with ASHRAE 90.1-2004 6.4.1.
Table 5.2: Chillers

Equipment Class
Air Cooled Chiller <530 kW (<150 tons) Air Cooled Chiller 530 kW (150 tons) *Centrifugal Water Cooled Chiller < 530 kW (<150 tons) *Centrifugal Water Cooled Chiller 530 and <1050 kW (150 and <300 tons) *Centrifugal Water Cooled Chiller 1050 kW ( 300 tons) Reciprocating Compressor, Water Cooled Chiller all sizes Rotary Screw and Scroll Compressor, Water Cooled Chiller <530 kW (<150 tons)

Minimum COP Minimum IPLV

2.90 3.05 5.80 5.80 6.30 4.20 4.70 3.16 3.32 6.09 6.17 6.61 5.05 5.49

Test Standard
ARI 550/590-1998 ARI 550/590-1998 ARI 550/590-1998 ARI 550/590-1998 ARI 550/590-1998 ARI 550/590-1998 ARI 550/590-1998

Energy Conservation Building Code (ECBC) User Guide

41

Heating, Ventilation and Air Conditioning

Rotary Screw and Scroll Compressor, Water 5.40 Cooled Chiller 530 and <1050 kW (150 and <300 tons) Rotary Screw and Scroll Compressor, Water 5.75 Cooled Chiller 1050 kW ( 300 tons) *These are aspirational values. For mandatory values refer to ASHRAE 90.1-2004

6.17

ARI 550/590-1998

6.43

ARI 550/590-1998

As per the Code: Unitary Air Conditioner shall meet IS 1391- Part 1 (Table 5.3), split air conditioner shall meet IS 1391 - Part 2 (Table 5.3), packaged air conditioner shall meet IS 8148 (Table 5.4) and boilers shall meet IS 13980 (the standard speciies the procedure with above 75% thermal eficiency.
Table 5.3: Power Consumption Ratings for Unitary Air Conditioners Under Test Conditions Table 5.4: Power Consumption Ratings for Split Air Conditioners Under Test Conditions

Rated Cooling Capacity (kcal/h)

1,500 2,250 3,000 3,750 4,500 6,000 7,500 9,000

Maximum Power Consumption (kW)

1.1 1.4 1.6 2.0 2.4 3.2 4.25 5.2

Rated Cooling Capacity (kcal/h)

3 000 4 500 6 000 7 500 9 000

Maximum Power Consumption (kW)

1.7 2.6 3.4 4.5 5.4

kW
1.7 2.6 3.5 4.4 5.2 7.0 8.7 10.5

kW
3.5 5.2 7.0 8.7 10.5

Source: Code No.: IS 1391 (Part-1): 1992 (amendment No. 2 Dec.2006 ) Cooling Capacity
Watts
10,000 17,500 26,250 35,000 52,000

Source: Code No.: IS 1319 (Part-2): 1992 (amendment No. 2 Dec.2006) Maximum Power Consumption in Watts
Water Cooled
3,750 6,000 9,000 11,500 17,000

Table 5.5: Power Consumption Rating for Packaged air Conditioners-under test conditions Tons of Refrigeration
3 5 7.5 10 15

Air Cooled
4,750 7,000 10,000 13,500 20,000

Source: Code No.: IS 8148: 2003 Selection of individual equipment eficiency should be considered in the context of the whole HVAC system. In a chilled-water system, for example, although the chiller is at the core of the system and typically is the single largest energy user, simply selecting a high-eficiency chiller does not guarantee high performance. Auxiliary equipment (such as fans and blowers) and design decisions (such as approach temperatures) can have substantial effects on overall eficiency. Thus, attention to overall system design and auxiliary components is critical to achieving optimal performance and comfort. Even in packaged air-conditioning systems, leaky ductwork, improper sizing, refrigerant charge, and air low rates can considerably affect energy performance.

5.2.3

Controls

Controls are one of the most critical elements for improving eficiency of any HVAC system. Controls determine how HVAC systems should operate to meet the design goals of comfort, eficiency, and cost-effective operation. In this context, the Code speciies the use of time clocks, temperature controls/thermostats, and two-speed or variable speed drives for fans.

Energy Conservation Building Code (ECBC) User Guide

42

Heating, Ventilation and Air Conditioning

5.2.3.1 Timeclock Control

As per the Code, All mechanical cooling and heating systems shall be controlled by a timeclock that: a. b. c. Can start and stop the system under different schedules for three different day-types per week Is capable of retaining programming and time setting during loss of power for a period of at least 10 hours, and

Includes an accessible manual override that allows temporary operation of the system for up to 2 hours Exceptions to the above are: a. b. Cooling systems < 28 kW (8 tons) Heating systems < 7 kW (2 tons)

5.2.3.2 Temperature Control

As per the Code: All heating and cooling equipment shall be temperature controlled. Where a unit provides both heating and cooling, controls shall be capable of providing a temperature dead band of 3C (5F) within which the supply of heating and cooling energy to the zone is shut off or reduced to a minimum. Where separate heating and cooling equipment serve the same temperature zone, thermostats shall be interlocked to prevent simultaneous heating and cooling. It is important to clearly establish design conditions and ensure adequate dead band between cooling and heating set points to avoid conlicting thermostat control conditions. Increasing the dead band can make the system more stable and eficient.

5.2.3.3 Controls for Cooling Towers and Closed Circuit Fluid Coolers
As per the Code: All cooling towers and closed circuit luid coolers shall have either two speed motors, pony motors, or variable speed drives controlling the fans. Box 5-I briely discusses the concept of Variable Speed Drive, and Box 5-J provides guidelines for improving energy and water eficiency in cooling towers.

Box 5-I: Variable Speed Drive

A variable speed drive (VSD) is an electronic device that controls the rotational speed of a piece of motor-driven equipment (e.g. a blower, compressor, fan, or pump). Speed control is obtained by adjusting the frequency of the voltage applied to the motor. This approach usually saves energy for varying-load applications. Through the application of VSD on the cooling tower fan, the fan speed can be reduced during lower ambient conditions for reducing energy consumption. However condenser water reset strategy may require condenser fan speeds to be maintained to improve chiller eficiency by lowering condenser water temperature. At lower loads the overall system eficiency should be the driver as pumping and tower fan energy form signiicant proportion of overall chiller plant energy.

Energy Conservation Building Code (ECBC) User Guide

43

Heating, Ventilation and Air Conditioning

Box 5-J: Energy and Water Eiciency in Cooling Towers

Energy and Water Eficiency in Cooling Towers Water-based HVAC systems offer signiicant energy savings due to the ability of water to transport large quantities of heat over relatively long distances, more eficiently than air-based systems. Additionally, they offer advantages such as smaller equipment size and cost, along with reduced maintenance and extended life of mechanical equipment. However, for water scarce urban centers in India, the viable installation and operation of cooling towers will require balancing needs for energy eficiency and water conservation simultaneously. Aircooled chillers are a good option to conserve water, however the trade-off is that these chillers consume more energy to provide the same amount of cooling when compared to water cooled machines with cooling towers. Energy Eficiency Measures: Proper site selection and sizing of the tower can reduce fan speed, capacity, and sound and help to conserve energy Centrifugal fans in favor of lower energy axial fans can reduce horsepower by 50% or more for the same capacity Fan control through two-speed motors, pony motors, or variable speed motors can save energy as well Water Eficiency Measures: An optimized bleed rate for the tower should be maintained to regulate water consumption. The evaporation rate is dependent on the load, which can vary widely and a constant bleed rate usually discharges more water than required. A properly operating conductivity meter can automatically control bleed to the proper amount required to maintain the desired tower chemistry in the system at all times. Contaminant induction should be minimized and a proper blow down rate should be maintained. Water treatment regimens are effective for water conservation, keeping the cooling loop cleaner, saving energy, reducing maintenance, and improving reliability of the entire cooling system. New technological solutions like hybrid wet-dry cooling tower designs, which combine wet and dry cooling can be adopted to reduce water use, some as much as 70% compared to conventional towers. Typically, a dry inned coil section is combined in series with an evaporative section in these units. The dry inned section handles as much of the load as possible, with the unit able to operate completely dry at reduced ambient. Both open and closed circuit versions are available. Source: Morrison F.: Whats up with Cooling Tower (2004). ASHRAE Journal 46 (7)

5.2.4

Piping and Ductwork

5.2.4.1 Pipe Insulation

To minimize heat losses, the Code requires that piping of heating and cooling systems, (including the storage tanks,) must be insulated. The Code speciies required R-values of insulation for heating and cooling systems based on the operating temperature of the system. These are as shown in Table 5.6 and Table 5.7.
Table 5.6: Insulation of Heating Systems Table 5.7: Insulation of Cooling Systems

Heating System
Designed Operating Temperature of Piping
60C and above Above 40C and below 60C

Cooling System
Designed Operating Temperature of Piping
Below 15C Split System

Insulation with Minimun R-value (m2K/W)

0.74 0.35

Insulation with Minimun R-value (m2K/W)

0.35 0.35

Refrigerant Suction Piping

As per the Code: Insulation exposed to weather shall be protected by aluminum sheet metal, painted canvas, or plastic cover. Cellular foam insulation shall be protected as above, or be painted with water retardant paint.

Energy Conservation Building Code (ECBC) User Guide

44

Heating, Ventilation and Air Conditioning

5.2.4.2 Ductwork
As per the Code: Ductwork shall be insulated in accordance with the Table 5.8.
Table 5.8: Ductwork Insulation

Required Insulationa (R-values in m2K/W)

Duct Location Exterior Ventilated Attic Unventilated Attic without Roof Insulation Unventilated Attic with Roof Insulation Unconditioned Buried
a Insulation

Supply Ducts R-1.4 R-1.4 R-1.4 R- 0.6 R- 0.6 No Requirement R- 0.6

Return Ducts R- 0.6 R- 0.6 R- 0.6 No Requirement No Requirement No Requirement No Requirement

Spaceb Spacec

Indirectly Conditioned

R-value is measured on a horizontal plane in accordance with ASTM C518 at a mean temperature of 24C (75F) at the installed thickness
bIncludes cIncludes

crawlspaces, both ventilated and non-ventilated return air plenums with or without exposed roofs above.

Table 5.9 provides R-value of a few insulating materials.

Table 5.9: Sample R-values for Duct Insulation Materials

Installed R-value1 (m2 K/W)

1.9 3.5

Typical Material Meeting or Exceeding the Given R-value2

in. Mineral iber duct liner per ASTM C 1071, Type 1 1 in. Mineral iber duct wrap per ASTM C 1290 1 in. Mineral iber duct liner per ASTM C 1071, Types I & II 1 in. Mineral iber board per ASTM C 612, Types IA & IB 1 in. Mineral iber duct board per UL 181 1 in. Mineral iber duct wrap per ASTM C 1290 1 in. Insulated lex duct per UL 181 1 in. Mineral iber duct liner per ASTM C1071, Types I & II 1 in. Mineral iber duct board per UL 181 1 in. Mineral iber board per ASTM C 612, Types IA & IB 2 in.. 2 lb/ft3 Mineral iber duct wrap per ASTM C 1290 2 in. 0.6 to 1 lb./ft3 Mineral iber duct wrap per ASTM C 1290 2 in. Insulated lex duct per UL 181

6.0

8.0

2 in. Mineral iber duct liner per ASTM C 1071, Types I & II 2 in. Mineral iber duct board per UL 181 2 in. Mineral iber board per ASTM C 612, Types IA & IB 3 in. lb/ft3 Mineral iber duct wrap insulation per ASTM C 1290 3 in. Insulated lex duct per UL 181

10.0

2 in. Mineral iber board per ASTM C 612, Types IA & IB

1 Listed R-values are for the insulation only as determined in accordance with ASTM C 518 at a mean temperature of 24C at the installed thickness and do not include air ilm resistance. 2 Consult with manufacturers for other materials or combinations of insulation thickness or density meeting the required R-value.

Source: ASHRAE 90.1 User Manual (2007), Table 6-D

Energy Conservation Building Code (ECBC) User Guide 45

Heating, Ventilation and Air Conditioning

Ductwork should be properly air sealed (Box 5-K) and also be protected from moisture absorption. Condensing moisture can cause many types of insulation, such as iberglass, to lose their insulating properties or degrade.

Box 5-K: Duct Sealing

Duct sealing is critical to avoid air leaks that prevent the HVAC system from functioning as designed and operated. The Code currently does not provide any guidance on ductwork sealing. The ASHRAE 90.1 energy code can be referred to for appropriate seal levels for all ductwork in order to minimize energy losses from the HVAC system. ASHRAE 90.1 (tables 6.2.4.3 A and 6.2.4.3 B) specify sealing requirements based on the duct location, static pressure classiication, and type of the duct (exhaust or return) as given below: ASHRAE 90.1 Table 6.2.4.3 A Minimum Duct Seal Level
Duct Location Outdoors Unconditioned Spaces Conditioned Spaces Duct Type Supply 498.2 Pa
A B C

Exhaust
C C B

Return
A B C

498.2 Pa
A A B

ASHRAE 90.1 Table 6.2.4.3 B Duct Seal Levels

Seal Level
A B C

Sealing Requirements
All transverse joints and longitudinal seams, and duct wall penetrations. Pressure-sensitive tape shall not be used as the primary sealant. All transverse joints and longitudinal seams. Pressure-sensitive tape shall not be used as the primary sealant Transverse joints only.

5.2.5

System Balancing

5.2.5.1 General
System balancing is a process for maintaining the performance of an HVAC system, and for providing the occupants with a comfortable conditioned space. Balancing an air or water-based HVAC system of buildings will make it more energy-eficient, provide improved thermal comfort, extend the life of the building equipment and reduce the cost of operating it. Balancing is achieved by optimizing the air/water distribution rates for the HVAC system. As per the Code: Construction documents shall require that all HVAC systems be balanced in accordance with generally accepted engineering standards. Construction documents shall require that a written balance report be provided to the owner or the designated representative of the building owner for HVAC systems serving zones with a total conditioned area exceeding 500 m2 (5,000 ft2). Box 5-L provides more information on the construction documents.

Box 5-L: Construction Documents

Construction documents provide vital information to the building owners on how to properly operate and maintain a system that has been properly balanced. Verify during inal inspection that an operations manual has been passed on to the building owner and that it contains the following information at a minimum. HVAC equipment capacity Equipment operation and maintenance manuals HVAC system control maintenance and calibration information, including wiring diagrams, schedules, and control sequence descriptions. A complete written narrative of how each system is intended to operate.
Energy Conservation Building Code (ECBC) User Guide 46

Heating, Ventilation and Air Conditioning

5.2.5.1.1 Air Systems Balancing Air System Balancing refers to the adjustment of airlow rates through air distribution system devices, such as fans and diffusers. This is done by adjusting the position of dampers, splitter vanes, extractors, etc., manually or by using automatic control devices, such as constant air volume or variable air volume boxes. Balancing is necessary to verify that each space served by a system receives the air volume designed for that space. Proper means for air balancing should be installed at each supply air outlet and zone terminal device. These include balancing dampers or other means of supply-air adjustment provided in the branch ducts or at each individual duct register, grille, or diffuser. Installation in the duct system of all devices used for balancing, shown on the approved mechanical plans, typically, on the ductwork layout, should be veriied. As per the Code: Air systems shall be balanced in a manner to minimize throttling losses. Then, for fans greater than 0.75 KW (1.0 HP), fans must then be adjusted to meet design low conditions. Box 5-M provides the concepts related to air handling units for air distribution systems for energy eficiency.

Box 5-M: Air Handling Unit Concepts

An air handler is responsible for moving air throughout the duct work in an air conditioning system. All air handlers contain a blower motor and squirrel cage blower housing which facilitates the movement of air. Most air handlers also include system controls, which are connected to the thermostat. Depending on the type of system, an air handler can also be integrated with a gas, oil, electric furnace, heat pump, and cooling coils (or evaporator coil for the air conditioning). High-eficiency air distribution systems can substantially reduce fan power required by an HVAC system, resulting in dramatic energy savings. The largest gains in eficiency for air distribution systems are realized in the system design phase for new constructions or major retroit projects. Passive or natural air transport systems have the highest eficiency, and successful, modern examples of this approach are steadily accumulating. For buildings that require mechanical ventilation, innovative design approaches and a methodical examination of the entire air system can greatly improve eficiency and effectiveness. Air-handling eficiency The energy required to move air is calculated as follows: (Flow X Static Pressure) /Eficiency All these factors can be manipulated to reduce the energy consumption of the system. Air low has a dominant effect on energy consumption because it shows up twice in the energy equation: as the irst term and as a squared function in the second term (pressure). The pressure a fan must work against depends on two primary factors: the low and duct design features such as diameter, length, surface treatment, and impediments such as elbows, ilters, and coils. Typical pressure losses are on the order of 2 to 6 inches water gauge (wg); an eficient system operates at less than 1.5 wg. A fans duty factor is the number of hours per year that it operates, sometimes presented as a percentage. Many large fans spin at full speed continuously (8,760 hours per year). Using simple or complex controls, duty factors can often be reduced to about 3,000 hours per year or less by limiting fan operation to occupied periods. The mechanical eficiency of the fan and its drive system can typically be raised from the 40 to 60% range to the mid-80% range. Wire to air eficiency will need to be considered and is function of motor eficiency x mechanical eficiency Design options for improving air distribution eficiency include: Variable-air-volume systems VAV diffusers Low-pressure-drop duct design Low-face-velocity air handlers Fan sizing and variable-frequency-drive motors Displacement ventilation systems. 5.2.5.1.2 Hydronic Systems Balancing Hydronic System Balancing refers to the adjustment of water low rates through distribution system devices,
Energy Conservation Building Code (ECBC) User Guide 47

Heating, Ventilation and Air Conditioning

such as pumps and coils, by manually adjusting the position of valves, or by using automatic control devices, such as low control valves. When something is balanced, it is even on both sides. Therefore, a balanced hydronic system is one that delivers even low to all of the devices on that piping system. Each component has an effective equal length of pipe on the supply and return. And when a system is balanced, all of the pressure drops are correct for the devices. When that happens, the highest eficiencies are possible in the system. One need not have to change system supply temperatures to accommodate one zone only. The system has the least amount of pressure drop possible, which translates into reduced pumping costs. A balanced hydronic system is one that is eficient. If a system that is not delivering the water to the right devices in the right amounts, then the system is out of balance. As per the Code: Hydronic systems shall be proportionately balanced in a manner to irst minimize throttling losses; then the pump impeller shall be trimmed or pump speed shall be adjusted to meet design low conditions. Exceptions to above: a. b. Impellers need not be trimmed nor pump speed adjusted for pumps with pump motors of 7.5 kW (10 hp) or less, Impellers need not be trimmed when throttling results in no greater than 5% of the nameplate horsepower draw, or 2.2 kW (3 hp), whichever is greater.

5.2.6

Condensers

5.2.6.1 Condenser Locations

A condenser is a heat exchanger that liqueies refrigerant vapor through heat removal. The typical condensing unit houses a compressor, a condenser fan motor, and coils, along with controls which make all the components work sequentially. As per the Code: Care shall be exercised in locating the condensers in such a manner that the heat sink is free of interference from heat discharge by devices located in adjoining spaces and also does not interfere with such other systems installed nearby. Condensers should be located in such a manner that there is no restriction to the air low around the condenser coils, there is no short-circuiting of discharge air to the intake side, and the heat discharge of other adjacent equipment is not anywhere the air intake of the condenser.

5.2.6.2 Treated Water for Condensers

Condenser water treatment is important to eliminate mineral buildup in condensers and chilled water systems. Mineral deposits create poor heat transfer situations there by reducing the eficiency of the unit. As per the Code: All high-rise buildings using centralized cooling water system shall use soft water for the condenser and chilled water system.

5.3 Prescriptive Requirements

As per the Code: The prescriptive requirements apply only if the HVAC system in the building meets the following criteria: a. b. c. d. Serves a single zone Cooling (if any) is provided by a unitary packaged or split-system air conditioner or heat pump Heating (if any) is provided by a unitary packaged or split-system heat pump, fuel-ired furnace, electric resistance heater, or baseboards connected to a boiler Outside air quantity is less than 1,400 l/s (3,000 cfm) and less than 70% of supply air at design conditions
48

Energy Conservation Building Code (ECBC) User Guide

Heating, Ventilation and Air Conditioning

Other HVAC systems shall comply with ASHRAE 90.1-2004, 6.5.

Box 5-N: Single Zone for HVAC

As per the Code, HVAC Zone is a space or group of spaces within a building with heating and cooling requirements that are suficiently similar so that desired conditions (e.g., temperature) can be maintained throughout using a single sensor (e.g., thermostat or temperature sensor).

Box 5-O: Heat Pump

A heat pump consists of one or more factory-made assemblies that normally include indoor conditioning coil, compressor, and outdoor coil, including means to provide a heating function. Heat pumps provide the function of air heating with controlled temperature, and may include the functions of air cooling.

5.3.1

Economizers

Economizers allow the use of outdoor air to cool the building when the outside temperature is cooler than that inside. An economizer consists of dampers, sensors, actuators, and logic devices that together decide how much outside air to bring into a building (See Figure 5.2).Under the right conditions, sensors and controls shut down the compressor and bring in the outside air through the economizer louvers. A properly operating economizer can cut energy costs by as much as 10% of a buildings total energy consumption, depending mostly on local climate and internal cooling loads.

Figure 5.2: Economizer Source: E Source Cooling Atlas

5.3.1.1 Air-Side Economizers

As per the Code: Each individual cooling fan system that has a design supply capacity over 1,200 l/s (2,500 cfm) and a total mechanical cooling capacity over 22 kW (6.3 tons) shall include either: a. An air economizer capable of modulating outside-air and return-air dampers to supply 100% of the design supply air quantity as outside-air; or

Energy Conservation Building Code (ECBC) User Guide

49

Heating, Ventilation and Air Conditioning

A water economizer capable of providing 100% of the expected system cooling load at outside air temperatures of 10C (50F) dry-bulb/7.2C (45F) wet-bulb and below Exceptions to above are: a. b. Projects in the hot-dry and warm-humid climate zones are exempt Individual ceiling mounted fan systems < 3,200 l/s (6,500 cfm) are exempt

b.

Box 5-P: Economizers

Air Economizer An air economizer is duct and damper arrangement and automatic control system that together allow a cooling system to supply outdoor air to reduce or eliminate the need for mechanical cooling during mild or cold weather. Water Economizer A water economizer is a system by which the supply air of a cooling system is cooled indirectly with water that is itself cooled by heat or mass transfer to the environment without the use of mechanical cooling.

5.3.1.2 Partial Cooling

One can use the buildings intrinsic thermal mass to reduce peak cooling loads by circulating cool night-time air to pre-cool the building prior to daily occupancy in the cooling season. The building control system can operate ventilation fans in the economizer mode on a scheduled basis. Care should be taken to prevent excessive fan operation that would offset cooling energy savings. It is also ensured that night humidity does not preclude the use of this strategy. As per the Code: Economizers shall be capable of providing partial cooling even when additional mechanical cooling is required to meet the cooling load.

5.3.1.3 Testing of Air-Side Economizer

As per the Code: Air-side economizers shall be tested in the ield following the requirements in Appendix F (of the Code) to ensure proper operation. Exception to above: Air economizers installed by the HVAC system equipment manufacturer and certiied to the building department as being factory calibrated and tested per the procedures in Appendix F (of the Code).

5.3.2

Variable Flow Hydronic Systems

Fluid from the heating or cooling source is supplied to heat transfer devices, such as coils and heat exchangers, and back through the hydronic system. The Code speciies the type of equipment and capabilities in such a way as to reduce pump energy. Variable luid low, automatic isolation valves, and variable speed drives enable the system to operate below design low when needed.

5.3.2.1 Variable Fluid Flow in Chilled or Hot Water System

As per the Code: Chilled or hot-water systems shall be designed for variable luid low and shall be capable of reducing pump low rates to no more than the larger of: a. b. 50% of the design low rate, or The minimum low required by the equipment manufacturer for proper operation of the chillers or boilers.

Energy Conservation Building Code (ECBC) User Guide

50

Heating, Ventilation and Air Conditioning

5.3.2.2 Automatic Isolation Valves

Two-way automatic isolation valves serve as a means of varying low rate in a hydronic system. As per the Code: Water cooled air-conditioning or heat pump units with a circulation pump motor greater than or equal to 3.7 kW (5 hp) shall have two-way automatic isolation valves on each water cooled air-conditioning or heat pump unit that are interlocked with the compressor to shut off condenser water low when the compressor is not operating.

5.3.2.3 Variable Speed Drives

Variable speed drives are required to control chilled water and condenser water systems for energy eficiency. As per the Code: Chilled water or condenser water systems that must comply with either 5.3.2.1 or 5.3.2.2 (of ECBC) and that have pump motors greater than or equal to 3.7 kW (5 hp) shall be controlled by variable speed drives.

Energy Conservation Building Code (ECBC) User Guide

51

Service Water Heating and Pumping

6. Service Water Heating and Pumping

6.1 General
or some building types such as large hotels and hospitals service water heating can be major energy consumer. Ineficiency in water heating is caused primarily by ineficiency of the heating equipment, and by heat loss from hot water storage tanks and distribution piping network. ECBC through mandatory requirements seeks to minimize energy usage in water heating systems by: Utilizing solar water heating Specifying heating equipment eficiency Maximizing heat recovery and minimizing electric heating Insulating hot water storage tanks and pipelines Reducing standby losses Reducing heat and evaporation losses in heated swimming pools

6.2 Mandatory Requirements

6.2.1 Solar Water Heating
As per the Code: Residential facilities, hotels and hospitals with a centralized system shall have solar water heating for at least 1/5 of the design capacity. Exception to above: Systems that use heat recovery for at least 1/5 of the design capacity. There are two types of solar water heaters. Passive heaters collect and store solar thermal energy for water heating applications and do not require electrical energy input for recirculating water through solar collector. Active heaters collect and store solar thermal energy for water heating applications and require electrical energy input for operation of recirculation pumps or other components. Figure 6.1 and Figure 6.2 show examples of solar water heating systems. An exception is provided by the Code for systems that use heat recovery systems for at least one-ifth (20%) of the design capacity. For example heat is rejected from the air conditioners condenser to the atmosphere. By recovering this waste heat and utilizing it to heat water, wherever feasible, it is possible to substantially reduce water-heating costs. Box 6-A provides information on various water heating systems normally used in practice.

Box 6-A: Types of Water Heaters

Storage Gas: A gas water heater designed to heat and store water at less than 80C. Water temperature is controlled with a thermostat. Storage Electric: An electric water heater designed to heat and store water at less than 80C. Water temperature is controlled with a thermostat. Storage electric water heaters have a manufacturers speciied capacity of at least two gallons. Storage Heat Pump: An electric water heater that uses a compressor to transfer thermal energy from one temperature level to a higher temperature level for the purpose of heating water. It includes all necessary auxiliary equipment such as fans, storage tanks, pumps or controls. Instantaneous Gas: A gas water heater controlled manually or automatically by water low activated control or a combination of water low and thermostatic controls.

Energy Conservation Building Code (ECBC) User Guide

52

Service Water Heating and Pumping

Instantaneous Electric: An electric water heater controlled automatically by a thermostat, instantaneous water heaters are not generally designed for use with solar water heating systems or as heat sources for indirect ired water heaters. They are also typically inappropriate for use with recirculation systems. Refer Box 6-B for more information. Indirect Gas: A water heater consisting of a storage tank with no heating elements or combustion devices, connected via piping and recirculating pump to a heat source consisting of a gas or oil ired boiler, or instantaneous gas water heater (see note following the deinitions of Instantaneous Gas and Electric). Passive Solar: Systems, which collect and store solar thermal energy for water heating applications and do not require electricity to recirculate water through a solar collector. Active Solar: Systems, which collect and store solar thermal energy for water heating applications requiring electricity to operate pumps or other components.

The simplest systems are passive solar water heaters, also called batch or bread box collectors, they are most common in regions that do not experience extensive periods of below freezing temperatures. The water in these solar collectors circulates without the aid of pumps or controls.

Figure 6.1: Batch Collector Passive System

Active solar water heaters use pumps to circulate water or an antifreeze solution through heatabsorbing solar thermal collectors.

Figure 6.2: Active Indirect System

Source: www.southface.org

Energy Conservation Building Code (ECBC) User Guide

53

Service Water Heating and Pumping

Box 6-B: Instantaneous Water Heaters

Instantaneous water heaters provide hot water only as it is needed. They do not produce the standby energy losses associated with storage water heaters, which can save money. Water heaters heat water directly without the use of a storage tank. Therefore, they avoid the standby heat losses associated with storage water heaters. When a hot water tap is turned on, cold water travels through a pipe into the unit. Either a gas burner or an electric element heats the water. As a result, demand water heaters deliver a constant supply of hot water. The heater dose not need a storage tank to ill up with enough hot water. However, the water heaters output limits the low rate.

Figure 6.3: Instantaneous Water Heater

6.2.2

Equipment Eiciency

As per the Code: Service water heating equipment shall meet or exceed the performance and minimum eficiency requirements presented in available Indian Standards a. Solar water heater shall meet the performance/minimum eficiency level mentioned in IS 13129 Part (1&2) b. Gas Instantaneous Water heaters shall meet the performance/minimum eficiency level mentioned in IS 15558 with above 80% thermal eficiency c. Electric water heater shall meet the performance /minimum eficiency level mentioned in IS 2082 The mandatory requirements for the Code include minimum eficiencies presented in relevant Indian Standards for the various water heating equipment such as electric and gas heaters, instantaneous heaters, boilers, and pool heaters. For Solar water heating systems, IS 13129 (Part 1) provides information on the Performance Rating Procedure Using Indoor Test Methods, and IS 13129 (Part 2) provides the information on the Procedure for System Performance Characterization and Yearly Performance Prediction. These standards however, do not provide any performance/minimum eficiency levels. For Gas Instantaneous Water Heaters, IS 15558 describes the information and procedure for the measurement of thermal eficiency of the heaters. As per this Standard, thermal eficiency of the water heaters (under test conditions) shall not be less than: 84 percent for water heaters with a nominal heat input exceeding 10 kW 82 percent for water heaters with a nominal heat input not exceeding 10 kW However, the Code speciies thermal eficiency of 80% or more.

Energy Conservation Building Code (ECBC) User Guide

54

Service Water Heating and Pumping

For Electric Water Heaters, IS 2082 (Part 1) covers the safety and performance requirements of heaters with rated capacities in the range of 6 liters to 200 liters. In these heaters, certain amount of energy is consumed to keep the water hot while it is not being used. This consumption of electricity is called as standing loss (or standby loss). Refer Box 6-C.

Box 6-C: Standby Losses

These losses account for energy lost while storing heated water. This includes any heat losses through the water heater tank wall, ittings, and lue, plus any pilot light energy. Standby loss depends on the design and insulation of the water heater, as well as the difference between the temperature of the water and that of the air around the tank. Water heating energy can be reduced by decreasing standby losses. The following table of IS 2082 (Part 1) speciies the standing loss in the heaters. For hot water temperature difference of 45C, in no case the standing loss should exceed the values speciied in the Table 6.1. Table 6.1: Standing Loss in Storage Type Electric Water Heaters Rated Capacity in Liters
6 10 15 25 35 50 70 100 140 200

Loss in kWh/day for 45 Difference

0.792 0.990 1.138 1.386 1.584 1.832 2.079 2.376 2.673 2.970

Source: IS 2082 (Part 1): 1993 (Reafirmed 2004) Edition 5.4 (2002-05) Stationary Storage Type Electric Water

Heaters-Speciication (Fourth Revision)

6.2.3

Supplementary Water Heating System

As per the Code: Supplemental Water Heating System shall be designed to maximize eficiency and shall incorporate and prioritize the following design features as shown: a. Maximum heat recovery from hot discharge system like condensers of air conditioning units b. Use of gas-ired heaters wherever gas is available c. Electric heater as last resort

6.2.4

Piping Insulation

As per the Code: Piping insulation shall comply with 5.2.4.1. The entire hot water system including the storage tanks, pipelines shall be insulated conforming to the relevant IS standards on materials and applications. Table from 5.2.4.1 of this Guide for piping insulation is reproduced below. Table 6.2: Insulation of Hot Water Piping. Heating System
Designed Operating Temperature of Piping
60C and above Above 40C and below 60C

Insulation with Minimum R-value (m2K/W)

0.74 0.35

Energy Conservation Building Code (ECBC) User Guide

55

Service Water Heating and Pumping

Box 6-D and Box 6-E provide guidelines for hot water temperature controls and measures for improving heating eficiency respectively.

Box 6-D: Guidelines for Temperature Controls

Water-heating systems are required to have controls that are adjustable down to a 49C setpoint or lower. An exception is made where a higher setting is recommended by the manufacturer to prevent condensation and possible corrosion. To comply with this requirement, the water heater must have thermostatic control with an accessible setpoint. This setpoint must be adjustable down to whichever is lower: 49C or the minimum manufacturers recommended setting to prevent condensation. Both standby and distribution losses will be minimized by designing a system to provide hot water at the minimum temperature required. In addition to the potential energy savings, maintaining water temperature as low as possible reduces corrosion and scaling of water heaters and components. Another important beneit is improved safety with respect to scalding. Accidental scalding from temperatures as low as 60C is responsible for numerous deaths each year. Designers should be aware that the bacteria that cause Legionnaires Disease has been found in service water heating systems and can colonize in hot water systems maintained below 46C. Careful maintenance practices can reduce the risk of contamination. In health-care facilities or service-water systems maintained below 60C, periodic lushing of the ixtures with high temperature water or other biological controls may be appropriate.

Box 6-E: Guidelines for Improving Water Heating System Eiciency

Reduce standby losses from storage tank and pipes. Lower Water Heating Temperature: Use a hot water system with a thermostat. Service water heating energy use and operating costs can be reduced by simply lowering the thermostat setting on your water heater. For each 5.5C (10F) reduction in water temperature, can save between 3%5% in energy costs. Insulate the storage tank: Install a water heater insulation blanket; the higher the R-value, the better. Use wire or twine or straps to insure that the blanket stays in place. Some new high-eficiency heaters should not be insulated; consult the equipment manual provided by the manufacturer. Gas water heaters should not be insulated on top or within about 8 of the bottom of the water tank. Set an electric water heater on a rigid foam insulation board. This step is most critical when the heater sits on a concrete slab, but its always a good idea. Install the water heater in a heated location. The colder the air surrounding the heater, the more the standby loss. Indoor gas heaters should be sealed combustion or fan-forced draft. Insulate pipes and use heat traps: Insulate all exposed pipes. The R-value of pipe insulation is dependent on wall thickness; thicker is better. A 5/8 wall thickness should be considered minimum for foam insulation, while 3 is the minimum for iberglass wrap. Heat trap nipples work best to eliminate convective losses from the tank into the plumbing, but pipe loops also work if the drop is at least 6.

6.2.5

Heat Traps

Heat traps are valves or loops of pipe that allow water to low into the water heater tank but prevent unwanted hot-water low out of the tank. The valves have balls inside that either loat or sink into a seat, which stop natural water circulation loop. Heat traps can help save energy and cost on the water heating bill by preventing convective heat losses through the inlet and outlet pipes. These specially designed valves come in pairs. The valves are designed differently for use in either the hot or cold water line. As per the Code: Vertical pipe risers serving storage water heaters and storage tanks not having integral heat traps and serving a non-recirculating system shall have heat traps on both the inlet and outlet piping as close as practical to the storage tank. Heat traps may either be installed internally by the manufacturer, installed as an after-market add-on, or sitefabricated. Site fabricated heat traps may be constructed by creating a loop or inverted U-shaped arrangement to the inlet and outlet pipes (See Figure 6.4 for general guidance).

Energy Conservation Building Code (ECBC) User Guide

56

Service Water Heating and Pumping

Figure 6.4: Heat Trap Elements

6.2.6

Swimming Pools

Heated swimming pools can be a source of considerable heat and water loss due to evaporation. Also, the cost of the energy required to maintain the temperature of the water in the pool at a level comfortable for swimming is a strong incentive to adopt measures which promote retention of heat in the pool and reduction in heat loss. As per the Code: Heated pools shall be provided with a vapor retardant pool cover on or at the water surface. Pools heated to more than 32C (90F) shall have a pool cover with a minimum insulation value of R-2.1 (R-12). Exception to above: Pools deriving over 60% of their energy from site-recovered energy or solar energy source.

6.2.7

Compliance Documentation

As per the Code: The application for approval shall furnish detailed calculation showing the design to ensure that at least 20% of the heating requirement shall be met from solar heat/heat recovery and not more than 80% of the heat shall be met from electrical heating. Wherever gas is available, not more than 20% of the heat shall be met from electrical heating.

Energy Conservation Building Code (ECBC) User Guide

57

Lighting

7.

Lighting

7.1 General

ighting accounts for 15% of total energy consumption in India. Lighting is an area that offers many energy eficiency opportunities in almost any building facility, existing or new.

A century ago, a person could read by the light of a single candle, but today a person in a typical ofice uses hundreds or even thousand times more light. Over the years, illumination standards have increased radically along with eficiency of lamps. People want light for different reasons, and a good lighting designer need to keep all of them in mind. Different tasks and building facilities require different amounts and types of light. For example, a surgeon in an operation theater needs lots of light with low glare and excellent color rendering, restaurant owners and diners often want low light levels, corporate boardrooms call for lighting that reinforces a feeling of importance and success while adapting to audio-visual presentations; retail outlets in many situations want to make their merchandise sparkle so that it draws the customers and encourages them to buy. An ofice executive needs modest ambient lighting level, good task lighting on work surface, and minimal glare to effectively read and work on computers. While energy eficiency is an attractive goal for many reasons, lighting designers also need to consider a host of other factors, including the effect of quality of light on the visual comfort and productivity of the occupants. Small improvement in lighting quality can improve productivity of the user substantially. In practice, the right quality and quantity of light can be provided eficiently (with less energy) by using the right technology and its effective integration with daylight. General Design Considerations Using eficient lighting equipment and controls is the best way to ensure lighting energy eficiency while maintaining or even improving lighting conditions. For instance, modern luorescent lighting, such as electronically ballasted T-8 systems, can provide the same quantity of light as older luorescent lighting while consuming as little as two-thirds of the energy. Similarly, compact luorescent sources are three to four times more eficient than the traditional incandescent lamps they are designed to replace. For a lighting designer an energy-eficient lighting design involves sensitive integration of many requirements and considerations that include building orientation, interior building layout, task illumination, daylight strategies, glazing speciication, choice of lighting system and controls etc. The designer is also responsible for making sure that lighting complies with the Code, meeting both mandatory and prescriptive requirements. The lighting requirements in the Code apply to: a. Interior spaces of buildings b. Exterior building features, including faades, illuminated roofs, architectural features, entrances, exits, loading docks, and illuminated canopies c. Exterior building grounds lighting that is provided through the buildings electrical service Exceptions to above: a. Emergency lighting that is automatically off during normal building operation and is powered by battery, generator, or other alternate power source b. Lighting in dwelling units

7.2 Mandatory Requirements

The mandatory requirements for lighting mostly relate to interior and exterior lighting controls.

Energy Conservation Building Code (ECBC) User Guide

58

Lighting

7.2.1

Lighting Control

Lighting controls allow lighting to be turned down or completely off when it is not needed the simplest way to save energy. Maximizing the use of controls involves developing a set of strategies that utilize the Code requirements for various devices, including on-off controls, dimming controls, and systems that combine the use of both types of equipment. These controls can be quite sophisticated, but in general, they perform two basic functions:1) they turn lights off when not needed, and 2) they modulate light output so that no more light than necessary is produced. The equipment required to achieve these functions varies in complexity from simple timers to intricate electronic dimming circuits, each applicable to different situations. Controls include time clocks, occupant and motion sensors, automatic or manual daylighting controls, and astronomical time switches (the automatic switches that adjust for the length of the day as it varies over the year).

Box 7-A: Manual Vs. Automatic Controls

Manual lighting controls range from a single switch to a bank of switches and dimmers that are actuated by toggles, rotary knobs, push buttons, remote control, and other means. Manual controls can be cost-effective options for small-scale situations. However, as the lighting system becomes larger, automated systems become more cost-effective and are better at controlling light. Manual controls may not give the desired results in real situations because the decision to shut off the lights when they are not needed is based entirely on human initiative. It is worthwhile to determine the amount of local vs. central control that is needed from the lighting control system.

7.2.1.1 Automatic Lighting Shutof

Although there is no simpler way to reduce the amount of energy consumed by lighting systems than to manually turn lights off whenever not needed, this is not done as often as it could be. In response to that problem, the Code requires several automatic switches that either work on time schedule or sense the presence of occupants. Automatic Control Strategies Several different approaches can be used to control electric lighting. The control hardware and design practices are discussed below: Scheduling Control: Use a time scheduling device to control lighting systems according to predetermined schedules. Occupancy Sensing: Control lights in response to the presence or absence of people in the space. Daylighting: Switch or dim electric lights in response to the presence or absence of daylight illumination in the space. Lumen Maintenance: Gradually adjust electric light levels over time to correspond with the depreciation of light output from aging lamps. As per the Code: Interior lighting systems in buildings larger than 500 m2 (5,000 ft) shall be equipped with an automatic control device. Within these buildings, all ofice areas less than 30 m2 (300 ft2) enclosed by walls or ceiling-height partitions, all meeting and conference rooms, all school classrooms, and all storage spaces shall be equipped with occupancy sensors. For other spaces, this automatic control device shall function on either a. A scheduled basis at speciic programmed times. An independent program schedule shall be provided for areas of no more than 2,500 m2 (25,000 ft) and not more than one loor; or, b. Occupancy sensors that shall turn the lighting off within 30 minutes of an occupant leaving the space. Light ixtures controlled by occupancy sensors shall have a wall-mounted, manual switch capable of turning off lights when the space is occupied. Exception to above: Lighting systems designed for 24-hour use.
Energy Conservation Building Code (ECBC) User Guide 59

Lighting

Box 7-B provides a brief on scheduling controls.

Box 7-B: Scheduling Controls

Programmable timing, also known as automatic time scheduling, is the oldest form of automatic lighting control. Time scheduling manages the on and off times of a buildings lighting systems. Scheduling systems function by turning off all or some of the lights when a building space is unoccupied. In the most basic time-scheduling scheme, a time switch switches lighting circuits on or off based on programmable schedules. For example, exterior lighting is usually switched on to correspond to sundown and is switched off again at daybreak. By contrast, time scheduling of interior lighting systems is based, for the most part, on occupancy schedules. In some cases, time switches are used to energize additional lighting control systems, such as daylighting controls, which are held off during unoccupied periods. Time-scheduling systems employ the following components: A central processor is usually capable of controlling several output channels, each of which may be assigned to one or more lighting circuits. Relays are series-wired to lighting control zones and are controlled by the central processor. Overrides are required to accommodate individuals who use the space during scheduled off hours. Individuals can activate manual switches or use telephone overrides to regain temporary control of the lights in a given space. Occupant-sensing devices are an alternative to scheduling controls and an acceptable means of meeting the requirement for automatic shutoff. The designer is free to arrange occupant sensing controls in any manner that makes sense for the building design. In ofice spaces, each room or space might have an occupant sensor. Of course, the smaller the area controlled, the greater the energy savings will be. In open ofice areas, several occupant sensors may be connected so that the lights remain on if any one of the sensors detects occupants. However, in order to satisfy the requirement, it is necessary that all the general lighting be controlled by one or more occupant sensors. Box 7-C provides more information on occupancy sensors.

Box 7-C: Occupancy Sensors

Occupancy sensors are automatic scheduling devices that detect motion and turn lights on and off accordingly. Most devices can be calibrated for sensitivity and for the length-of-time delay between the last detected occupancy and extinguishing of the lights. The most energy-eficient occupancy sensors, known as manualon, automatic-off, require that the user manually switch on the lights when entering a controlled zone (the lights off function is still automatic). Occupancy sensor systems typically consist of a motion detector, a control unit, and a relay. Usually, two or more of the components are integrated into one package. Most systems also require a power supply in the form of a transformer, which steps down the building voltage to 24V. The detector collects information, then sends it to the controller, where it is processed. Output from the controller activates the relay, which in turn switches the light circuit. There are two major types of occupancy controls. Wallbox units are designed to it into a standard wall switch box and operate on the building voltage (i.e., a separate power supply is not required). They are excellent, inexpensive replacements for standard wall switches. Their main limitation is their relatively short range. Consequently, they tend to be used in small ofices and meeting rooms. Wall and Ceiling units typically contain an integrated sensor/controller unit wired (Class 2) to a switch pack containing the relay and power supply. They are far more popular than wallbox units and have very few application limitations.

Energy Conservation Building Code (ECBC) User Guide

60

Lighting

Occupancy-sensing lighting controls represent a reinement of the technology developed in the early 1970s to detect intruders for residential and commercial security applications. With lighting control, two different means of detecting occupancy are used: Passive Infrared (PIR) sensors perceive and respond to the heat patterns of motion. This same technology is used in most residential and commercial security systems. The chief advantage of PIR sensors is that they are relatively inexpensive and reliable. They very rarely false trigger (that is, respond to non occupant motion in a space). The major limitation of PIR sensors is that they are strictly line-of-sight devices, unable to see around corners or partitions. Ultrasound (US) detectors radiate ultrasonic waves into a space, then read the frequency of the relected waves. Motion causes a slight shift in frequency, which the detector interprets as occupancy. They are more sensitive than PIR sensors, which is both an advantage and a disadvantage. They are often used very effectively in partitioned spaces but are also more prone to false triggering due to their sensitivity to air movement. Proper design and installation minimizes this potential problem.

7.2.1.2 Space Control

Along with controls for individual lights or sets of ixtures, master controls are required for each space which can shut off all the lights within the space. For example, the last person leaving the ofice is much more likely to use a master switch than to go through the ofice turning off every switch. Similarly, a cleaning crew can easily use master switches to turn lights off at the end of a working day. As per Code: Each space enclosed by ceiling-height partitions is required to have at least one control device to independently control the lighting within the space. The device can be a switch that is activated either manually or automatically by sensing an occupant sensor. Each control device, regardless of type, shall have the following functions: a. Control a maximum of 250 m2 (2,500 ft2) for a space less than or equal to 1,000 m2 (10,000 ft2), and a maximum of 1,000 m2 (10,000 ft2) for a space greater than 1,000 m2 (10,000 ft2) b. Be capable of overriding the required shutoff control [ECBC 7.2.1.1] for no more than 2 hours c. Be readily accessible and located so the occupant can see the control. Box 7-D summarizes the Code requirements.

Box 7-D: Space Area and Lighting Controls

S.No.
1 2

Space Area
Up to 1000 m2 More than 1000 m2

Coverage Area for each control device

250 m2 max. 1000 m2 max.

Exception to (c) above: The required control device may be remotely installed if required for reasons of safety or security. A remotely located device shall have a pilot light indicator as part of or next to the control device and shall be clearly labeled to identify the controlled lighting. An exception to (c) is provided for control devices that need to be remotely installed for reasons of safety or security. However, a remotely located device must have a pilot light indicator as part of or next to the control device and it must be clearly labeled to identify the controlled lighting device.

Energy Conservation Building Code (ECBC) User Guide

61

Lighting

Box 7-E: Lighting Controls

Q: An open ofice area is 900 m2. How many controls are required for this space? A: Minimum four, since this space is smaller than 1,000 m2 and each space control can serve a maximum area of 250 m2 . Q: In an open ofice 1,500 m2, how many minimum controls are required? A: Minimum two, since this space is larger than 1,000 m2 each control can serve a maximum area of 1,000 m2.

7.2.1.3 Control in Daylighted Areas

As per the Code: Luminaire in daylighted areas greater than 25 m2 (250 ft2) shall be equipped with either a manual or automatic control device that: Is capable of reducing the light output of the luminaires in the daylighted areas by at least 50% Controls only the luminaires located entirely within the daylighted area.

Box 7-F: Luminaire

As per ECBC: A complete lighting unit consisting of a lamp or lamps together with the housing designed to distribute the light, position and protect the lamps, and connect the lamps to the power supply. Appendix A of ECBC provides more information on the daylighted area.

7.2.1.4 Exterior Lighting Control

As per the Code: Lighting for all exterior applications not exempted in 7.3.5 (of the Code) shall be controlled by a photosensor or astronomical time switch that is capable of automatically turning off the exterior lighting when daylight is available or the lighting is not required.

7.2.1.5 Additional Control

As per the Code: The following specialty lighting spaces are required to have a control device that separates lighting control from that of the general lighting The following lighting applications shall be equipped with a control device to control such lighting independently of general lighting: a. Display/Accent Lighting: Display or accent lighting greater than 300 m2 (3,000 ft2) area shall have a separate control device b. Case Lighting: Lighting in cases used for display purposes greater than 300 m2 (3,000 ft2) area shall be equipped with a separate control device c. Hotel and Motel Guest Room Lighting: Hotel and motel guest rooms and guest suites shall have a master control device at the main room entry that controls all permanently installed luminaires and switched receptacles d. Task Lighting: Supplemental task lighting including permanently installed under-shelf or undercabinet lighting shall have a control device integral to the luminaires or be controlled by a wall-mounted control device provided the control device complies with 7.2.1.2 (of ECBC) e. Non-visual Lighting: Lighting for non-visual applications, such as plant growth and food-warming, shall be equipped with a separate control device

Energy Conservation Building Code (ECBC) User Guide

62

Lighting

f. Demonstration Lighting: Lighting equipment that is for sale or for demonstrations in lighting education shall be equipped with a separate control device accessible only to authorized personnel Box 7-G provides more information and guidelines for installation of controls for the above lighting applications:

Box 7-G: Additional Control

Many special lighting applications must be controlled separately, including display lighting in retail stores, case lighting, hotel/motel guest rooms, task lighting, non-visual lighting applications, and demonstration lighting. These are discussed below. Display/Accent Lighting Lighting used to highlight artwork or merchandise in retail stores, art galleries, lobbies, and other spaces must have a separate lighting control. This additional control can save considerable energy since the hours required for display lighting are generally fewer than the hours that the space is occupied. In a retail store, for instance, employees typically arrive one to two hours before the store opens in order to prepare the store, and often employees need to stay for an hour or two after the store closes. Without a separate control for display lighting, the display lighting would have to be operated for two to four hours each day when it isnt needed. Controls for display lighting can be situated in remote locations, but it is advisable that they have indicator lights and be clearly marked to indicate which lighting is controlled. Case Lighting Lighting is frequently installed in closed casework for the display of jewelry and other ine merchandise. Such lighting is required to have a separate control from that used for general illumination of the space. The reason for this requirement is the same as for display lighting: the case lighting is only needed during store hours, not during the entire occupancy period of the space. Usually, the control for case lighting is integral to the case. Hotel/Motel Guest Room Lighting A master lighting control is required at the entry door of hotel and motel guest rooms to control all permanently installed luminaires and switched receptacles. The control is usually a three-way device wired in combination with local controls. In multiple-room suites, a single master control must be located at the main entrance. This master lighting control allows guests or the housekeeping staff to turn off all permanently installed luminaires when they are exiting the room. Task Lighting All supplemental task lighting in a space shall have a separate control. Desk lamps will inherently meet this requirement, but the requirement also applies to permanently installed under-shelf or under-cabinet lighting. Such lighting can have a switch integral to the luminaires or be controlled by a wall-mounted control device, provided the control device is accessible and the controlled lighting can be observed when the switch is toggled. Non-Visual Lighting Lighting needed for non-visual purposes, such as plant growth or food warming, must have a separate control. This is because such lighting is likely to be needed at different times than the general lighting. Demonstration Lighting Lighting on display in retail lighting stores and lighting that is being demonstrated in classrooms and lighting education facilities must have a separate control. Again, the justiication is that such lighting is operated on a separate schedule from the general lighting.

7.2.2

Exit Signs

As per the Code: Internally-illuminated exit signs shall not exceed 5W per face. Electrically powered exit signs normally use incandescent bulbs. Most LED and some CFL exit signs can meet ECBC requirement. Due to their low power consumption, LED exit signs can be purchased with built-in backup power supplies (i.e., batteries). With an estimated service life of 10 years or more, LEDs require signiicantly fewer lamp replacements than exit signs equipped with either incandescent lamps or CFLs.
Energy Conservation Building Code (ECBC) User Guide 63

Lighting

7.2.3

Exterior Building Grounds Lighting

As per the Code: Lighting for exterior building grounds luminaires which operate at greater than 100W shall contain lamps having a minimum eficacy of 60 lm/W unless the luminaire is controlled by a motion sensor or exempt under 7.1 of ECBC. Eficacy of Lamp (with or without ballast) is the lumens produced by a lamp/ballast system divided by the total watts of input power (including the ballast), expressed in lumens per watt. Figure 7.1 and Figure 7.2 provide a broad range of lamp eficacy of commonly used lamps. As shown below in Figure 7.2, luminaires meeting exterior building ground lighting requirements can be luorescent, mercury vapor and high pressure sodium.

Figure 7.1: Relative Eicacy of Major Light Sources (Lumens/Watt)

Figure 7.2: Watts per Lighting System Eiciency

Energy Conservation Building Code (ECBC) User Guide

64

Lighting

Box 7-H: Lighting Controls

High-eficiency lighting components, such as T-8 luorescent lamps and electronic high-frequency ballasts, make a signiicant impact on lighting energy and its associated costs by reducing the kW required to illuminate buildings. Lighting controls, on the other hand, affect lighting energy by directly reducing lightings time of use. Some lighting control techniques, such as using photocell controls in building spaces that incorporate daylighting, not only reduce lighting time of use but also decrease lighting power and may even reduce the average cost of electricity by eliminating some lighting kW during peak demand periods. Source: ASHRAE Manual 2004.

7.3 Prescriptive Requirements

The prescriptive requirements of the Code regulates both interior and exterior lighting power.

7.3.1

Interior Lighting Power

The prescriptive lighting requirements limit the installed electric wattage for interior building lighting. As with the other sections of the Code, however, these lighting power requirements are minimum requirements. Designers working on speciic projects may often be able to design more eficient lighting systems. For interior lighting power requirements, the installed lighting power used by luminaires, including lamps, ballasts, current regulators, and central devices (except as speciically exempted in 7.1) is irst calculated using the procedure discussed under 7.3.4.1 of ECBC. Calculated installed power is then compared with the maximum permissible Interior Light Power Densities, speciied for various building types (Building Area Method) or building space functions (Space Function Method) under table 7.1 and 7.2 of ECBC respectively. These two are discussed in more detail at 7.3.2 and 7.3.3.

Box 7-I: Lighting Power Allowance

1. Interior lighting power allowance: the maximum lighting power in watts allowed for the interior of a building 2. Exterior lighting power allowance: the maximum lighting power in watts allowed for the exterior of a building Interior lighting includes all permanently installed general and task lighting shown on the plans. Interior lighting, for a building or a separately metered or permitted portion of a building, shall not exceed allowed power limits. The building area method is the simplest method to follow since fewer calculations are required. However, if the project applies to only a portion of the entire building, is not listed as a building type, or has more than one occupancy type, the space function method should be used to determine compliance. Trade-off of lighting power allowances are not permitted between portions of a building where different methods are used. There are many exceptions to the lighting power requirement, generally for specialized lighting. These are listed in ECBC 7.3.1.

7.3.2

Building Area Method

This method provides the procedure of calculating total watts per square meter for the entire building based on its type. The sum of all the interior lighting power for various areas of the building cannot exceed the total watts to be in compliance. The irst step is to identify the allowed power lighting density for appropriate building area types listed in Table 7.1 of ECBC. If more than one listed type applies to the area, the more general building area type should be used.
Energy Conservation Building Code (ECBC) User Guide 65

Lighting

The second step is to calculate the gross lighted loor area for each of the building area types (this can be done using the building plans). Finally, the last step is to multiply the allowed watts per square meter listed for each selected building type by the corresponding lighted loor areas to determine the allowed light power allowance. Table 7.1: Interior Lighting Power- Building Area Method (ECBC Table 7.1) Building Area Type
Automotive Facility Convention Center Dining: Bar Lounge/Leisure Dining: Cafeteria/Fast Food Dining: Family Dormitory/Hostel Gymnasium Health care-Clinic Hospital/Health Care Hotel Library Manufacturing Facility Motel Motion Picture Theater

LPD (W/m2)
9.7 12.9 14.0 15.1 17.2 10.8 11.8 10.8 12.9 10.8 14.0 14.0 10.8 12.9

Building Area Type

Multifamily Residential Museum Ofice Parking Garage Performing Arts Theater Police/Fire Station Post Ofice/Town Hall Religious Building Retail/Mall School/University Sports Arena Transportation Warehouse Workshop

LPD (W/m2)
7.5 11.8 10.8 3.2 17.2 10.8 11.8 14.0 16.1 12.9 11.8 10.8 8.6 15.1

In cases where both a general building area type and a speciic building area type are listed, the speciic building area type shall apply.

7.3.3

Space Function Method

Similar to the building area method, the irst step of the space function method is to identify the appropriate building type and their allowed lighting power densities, which varies according to the function of the space. These are listed in ECBC Table 7.2, Interior Lighting Power Space Function Method. Table 7.2: Interior Lighting Power- Space Function Method (ECBC Table 7.2) Space Function
Ofice-enclosed Ofice-open plan Conference/Meeting/Multipurpose Classroom/Lecture/Training Lobby* For Hotel For Performing Arts Theater For Motion Picture Theater For Gymnasium For Convention Center For Religious Buildings For Sports Arena For Performing Arts Theater For Motion Picture Theater For Transportation

LPD (W/m2)
11.8 11.8 14.0 15.1 14.0 11.8 35.5 11.8 9.7 4.3 7.5 18.3 4.3 28.0 12.9 5.4 6.5 2.2 Hospital

Space Function
For Reading Area For Emergency For Recovery For Nurse Station For Exam Treatment For Pharmacy For Patient Room For Operating Room For Nursery For Medical Supply For Physical Therapy For Radiology For Laundry Washing

LPD (W/m2)
12.9 29.1 8.6 10.8 16.1 12.9 7.5 23.7 6.5 15.1 9.7 4.3 6.5 7.5 12.9 18.3

Audience/Seating Area*

Automotive Service Repair Manufacturing Facility For Low Bay (<8m ceiling) For High Bay (>8m ceiling)

Atrium-irst three loors Atrium-each additional loor

Energy Conservation Building Code (ECBC) User Guide

66

Lighting

Lounge/Recreation* For Hospital For Hotel For Motel For Bar Lounge/Leisure Dining For Family Dining Food Preparation Dining Area*

12.9 8.6 9.7 14.0 12.9 15.1 22.6 12.9 15.1 9.7 6.5 5.4 10.8 5.4 6.5 8.6 9.7 3.2 8.6 16.1 20.5 14.0

For Detailed Manufacturing For Equipment Room For Control Room

22.6 12.9 5.4 11.8 11.8 10.8 18.3 16.1 18.3 18.3 29.1 24.8 15.1 15.1 9.7 2.2 6.5 10.8 16.1

Hotel/Motel Guest Rooms Dormitory Living Quarters Museum Retail For Sales Area For Mall Concourse For Ring Sports Area For Court Sports Area For Indoor Field Area For Fine Material Storage For General Exhibition For Restoration

Laboratory Restrooms Dressing/Locker/Fitting Room Corridor/Transition* For Hospital For Manufacturing Facility

Bank Ofice Banking Activity Area

Sports Arena

Stairs-active Active Storage* For Hospital For Museum Inactive Storage*

Warehouse For Medium/Bulky Material Storage Parking Garage Garage Area Transportation For Airport Concourse For Air/Train/Bus Baggage Area

Electrical/Mechanical Facility Workshop Convention Center Exhibit Space Library * For For Card File & Cataloging For Stacks

11.8 18.3

For Ticket Counter Terminal

all facilities except the following

Second, for each space that is enclosed by partitions which are 80% or greater than ceiling height, the gross interior loor area must be determined. This applies to all space area types except for retail. The gross interior loor area should be calculated by measuring to the center of the partition walls and must also include spaces allotted to balconies or other projections. Finally, the individual lighting power allowances for each space is determined by multiplying its gross lighted loor area by the allowed lighting power density for that space. The lighting power allowances are summed to equal the Interior Lighting Power Allowance for the building.

7.3.4

Installed Interior Lighting Power

As per the Code: The installed interior lighting power calculated for compliance with 7.3 of the Code shall include all power used by the luminaires, including lamps, ballasts, current regulators, and control devices except as speciically exempted in 7.1 of the Code. Exception to above: If two or more independently operating lighting systems in a space are controlled to prevent simultaneous user operation, the installed interior lighting power shall be based solely on the lighting system with the highest power.

Energy Conservation Building Code (ECBC) User Guide

67

Lighting

7.3.4.1 Luminaire Wattage

The Code requires that luminaire wattage be incorporated into the installed interior lighting power calculation as follows: a. The wattage of incandescent luminaires with medium base sockets and not containing permanently installed ballasts shall be the maximum labeled wattage of the luminaires b. The wattage of luminaires containing permanently installed ballasts shall be the operating input wattage of the speciied lamp/ballast combination based on values from manufacturers catalogs or values from independent testing laboratory reports c. The wattage of all other miscellaneous luminaire types not described in (a) or (b) shall be the speciied wattage of the luminaires d. The wattage of lighting track, plug-in busway, and lexible-lighting systems that allow the addition and/ or relocation of luminaires without altering the wiring of the system shall be the larger of the speciied wattage of the luminaires included in the system or 135 W/m (45 W/ft). Systems with integral overload protection, such as fuses or circuit breakers, shall be rated at 100% of the maximum rated load of the limiting device

7.3.5

Exterior Lighting Power

Lighting power limits are speciied for building exterior lighting applications in Table 7.3 of the Code. The connected lighting power for these applications must not exceed these allowed limits. In addition, trade-offs between applications are not permitted. Exemptions are allowed for the following lighting applications, only if they are equipped by an independent control device: a. Specialized signal, directional, and marker lighting associated with transportation b. Lighting used to highlight features of public monuments and registered historic landmark structures or buildings c. Lighting that is integral to advertising signage d. Lighting that is speciically designated as required by a health or life safety statute, ordinance, or regulation Any exterior lighting applications not listed in Table 7.3 of the Code, and not exempt (as described above), are required to simply comply with the mandatory requirements in 7.2.3 of the Code. This requires luminaires operating at greater than 100W to contain lamps with minimum eficacy of 60 lm/W, unless the luminaire is controlled by a motion sensor. Table 7.3: Exterior Lighting Building Power (ECBC Table 7.3) Exterior Lighting Applications
Building entrance (with canopy) Building entrance (without canopy) Building exit Building facades

Power Limits
13 W/m2 (1.3 W/ft2) of canopied area 90 W/lin m (30 W/lin f) of door width 60 W/lin m (20 W/lin f) of door width 2 W/m2 (0.2 W/ft2) of vertical facade area

Energy Conservation Building Code (ECBC) User Guide

68

Electrical Power

8. Electrical Power
8.1 General

CBC has only mandatory requirements for electric power systems installed in buildings. These provisions are related to distribution transformers, electric motors, power factor, and distribution losses.

8.2 Mandatory Requirements

The mandatory requirements of the Code, cover the following electrical equipment and systems of building: Transformers Energy- Eficient Motors Power Factor Correction Electrical Metering and Monitoring Power Distribution Systems

8.2.1

Transformers

Transformer is a static device, which is used to either increase (Step up) or decrease (Step down) the input supply voltage depending on the application and requirement. Transformers consist of two or more coils that are electrically insulated, but magnetically linked (see Figure 8.1). The primary coil connected to the power source and secondary coil connects to the load.

Figure 8.1: Transformer Power transmitted from power plants, is in the form of high-tension voltage (400 kV - 33 kV). The reasons for transmitting HT voltage are: Reduced conductor size and investment on conductors Reduced the transmission losses and voltage drop. At the user end, equipment with various voltage rating is used for different applications. Hence, the transmitted voltage is irst stepped down (11 kV - 230V) through distribution transformers and then the power supply is distributed to the various sections and equipment. Distribution transformers are used normally in all commercial buildings. They are kept energized around the clock providing power to the buildings electrical equipment.

8.2.1.1 Maximum Allowable Power Transformer Losses

Transformers are of two types - Dry type and Oil illed. Fire safety and environmental concerns associated with transformers are important. Oil illed transformers are not installed at ire hazardous places. Dry type transformer is used when it has to be located near the load center which may be in a hazardous place. As there is no oil used in the transformer and special type of ire resistant insulation are used for the windings, the ire risk is considerably reduced in these transformers.
Energy Conservation Building Code (ECBC) User Guide 69

Electrical Power

Distribution transformers consume energy even when the building is not occupied or its equipment are not operating, resulting in energy loss. Transformers losses are discussed in Box 8-A.

Box 8-A: Transformer Eiciency and Losses

The eficiency of transformers normally varies anywhere between 96 to 99 percent. The eficiency not only depends on the design, but also, on the effective operating load. Transformer losses consist of two parts: No-load Loss and Load Loss No-load Loss (also called core loss) is the power consumed to sustain the magnetic ield in the transformer's steel core. Core loss occurs whenever the transformer is energized; and it does not vary with load. Core losses are caused by two factors: hysteresis and eddy current losses. Hysteresis loss is that energy loss caused by reversing of the magnetic ield in the core as the magnetizing alternating current rises and falls and reverses direction. Eddy current loss is a result of induced currents circulating in the core. Load Loss (also called copper loss) is associated with full-load current low in the transformer windings. Copper loss is power lost in the primary and secondary windings of a transformer due to the ohmic resistance of the windings. Copper loss varies with the square of the load current. (P=I2R). Transformer losses as a percentage of load is given in the Figure 8.2.

Figure 8.2: Transformer loss vs % Load For a given transformer, the manufacturer can supply values for no-load loss, PNo-load, and load loss, PLoad. The total transformer loss, PTotal, at any load level can then be calculated from: PTotal = PNo-load+ (% Load/100)2 PLoad Source: Energy Eficiency in Electrical Utilities, Bureau of Energy Eficiency, 2005. As per the Code: Power transformers of the proper ratings and design must be selected to satisfy the minimum acceptable eficiency at 50% and full load rating. In addition, the transformer must be selected such that it minimizes the total of its initial cost in addition to the present value of the cost of its total lost energy while serving its estimated loads during its respective life span. ECBC lists various transformer sizes of dry-type and oil-illed transformers and their associated losses at 50% and full load rating (Table 8.1 and Table 8.2 of ECBC).

Energy Conservation Building Code (ECBC) User Guide

70

Electrical Power

Table 8.1: Dry-Type Transformers (ECBC Table 8.1) Rating KVA Max. Losses at 50% loading1 [kW]
Up to 22 kV class
100 160 200 250 315 400 500 630 800 1000 1250 1600 2000 2500 0.94 1.29 1.5 1.7 2 2.38 2.8 3.34 3.88 4.5 5.19 6.32 7.5 9.25 2.4 3.3 3.8 4.32 5.04 6.04 7.25 8.82 10.24 12 13.87 16.8 20 24.75 1.12 1.42 1.75 1.97 2.4 2.9 3.3 3.95 4.65 5.3 6.25 7.5 8.88 10.75

Max. Losses at 100% loading1 [kW]

Total losses at 50% loading1 [kW]

Total losses at rated load1 [kW]

2.4 3.3 4 4.6 5.4 6.8 7.8 9.2 11.4 12.8 14.5 18 21.4 26.5

33 kV class

1Total loss values given in above table are applicable for thermal classes E, B & F and have component of load loss at reference

temperature according to clause 17 of IS 2026: Part 11. i.e., average winding temperature rise as given in column 2 of Table 8.2 plus 30C. An increase of 7% on total for thermal class H is allowed.

Table 8.2: Oil Filled Transformers (ECBC Table 8.2) Rating KVA Max. Losses at 50% loading1 [kW]
Up to 11 kV class
100 160 200 250 315 400 500 630 1000 1250 1600 2000 2500 0.52 0.77 0.89 1.05 1.10 1.45 1.60 2.00 3.00 3.60 4.50 5.40 6.50 1.80 2.20 2.70 3.32 3.63 4.63 5.50 6.64 9.80 12.00 15.00 18.40 22.50 0.56 0.78 0.90 -1.30 1.52 1.95 2.30 3.45 4.00 4.85 5.70 7.05

Max. Losses at 100% loading1 [kW]

Total losses at 50% loading1 [kW]

Total losses at rated load1 [kW]

1.82 2.58 3.00 -4.30 5.10 6.45 7.60 11.35 13.25 16.00 18.50 23.00

33 kV class

1Total loss values given in above table are applicable for thermal classes E, B & F and have component of load loss at reference

temperature according to clause 17 of IS 2026: Part 11. i.e., average winding temperature rise as given in column 2 of Table 8.2 plus 30C. An increase of 7% on total for thermal class H is allowed.

8.2.1.2 Measurement and Reporting of Transformer Losses

As per the Code: All measurement of losses shall be carried out by using calibrated digital meters of class 0.5 or better accuracy and certiied by the manufacturer. All transformers of capacity of 500 kVA and above would be equipped with additional metering class current transformers (CTs) and potential transformers (PTs) additional to requirements of Utilities so that periodic loss monitoring study may be carried out.
Energy Conservation Building Code (ECBC) User Guide 71

Electrical Power

8.2.2

Energy-Eicient Motors

Electric motors convert electrical energy into mechanical energy. Induction motors are the most commonly used prime mover for various equipment in buildings. In induction motors, the induced magnetic ield of the stator winding induces a current in the rotor. This induced rotor current produces a second magnetic ield, which tries to oppose the stator magnetic ield, and this causes the rotor to rotate. The 3-phase squirrel cage induction motor is the workhorse of most applications; it is rugged and reliable, and is by far the most common motor type used. These motors drive pumps, blowers and fans, compressors, conveyers and production lines. The 3-phase induction motor has three windings each connected to a separate phase of the power supply. Box 8-B provides more information on the induction motors.

Box 8-B: Induction motors

The induction motor is the dominant motor in use today with over 90 percent of the installed horsepower largely because it is rugged, has no brushes or slip rings, and is simple, reliable, and cheap. Figure 7-2 shows the spectrum of common motor types including induction motors. As with most motors, the induction motor has stator and rotor magnetic ields that interact to spin a shaft which provides torque for performing useful work. The stator and rotor magnetic ields in an induction motor are each created differently. The stator ield results from applying AC voltage directly to copper windings distributed around the circumference of the stator, causing the magnetic ield to rotate with the sinusoidally varying input power. The speed at which the stator ield rotatesthe motors synchronous speed depends on the construction of the motor. The induction motor is unique in how it develops its rotor ield. Typically, the rotor has bars that circulate currents that generate the rotor ield. Instead of connecting the bars to a power supply as for the stator ield, or otherwise creating a ield using a permanent magnet, the rotor ield is created by current induced in the rotor bars by the rotating stator ield. The rotor ield thus rotates at the same speed as the stator ield; however, it is offset by a certain angle that increases as more motor torque is required. Although induction motors are normally considered ixed speed machines, one potential disadvantage is that their operating speed will change with both load and voltage. In fact, it is dificult to ind two induction motors that will operate at exactly the same speed, even when operated at identical voltage and frequency, and driving identical loads. There are two major classes of induction motors, varying in winding pattern and construction: squirrel-cage motorsin which conductive bars mounted in the laminated rotor and held by heavy end rings that shortcircuit them at both ends, form the rotor windings and wound-rotor motors, in which coils of wire form the rotor windings. In wound-rotor motors, the windings are generally connected via slip rings and brushes to a variable resistance which can vary the motors speed and torque. Induction motors can be constructed so that different pole pairs can be connected and disconnected as desired at the terminal box, producing a variety of speeds. Such squirrel-cage induction motors are multispeed (usually two speed), but are not variable-speed if operating from a supply at ixed frequency. In another variation, part-winding start induction motors energize part of the winding when starting and the rest later, in one or more steps, so as to reduce starting torque or current. Induction motors can be constructed for single or polyphase operation with most motors over 20 horsepower designed for three-phase power. Source: E- Source Technology Atlas Series Volume IV, Drive Power Motor Eficiency is the ratio of the useful mechanical power output to the total electric power input to the motor. Like all electromechanical equipment, motors consume some extra energy in order to make the conversion. Eficiency relects how much total energy a motor uses in relation to the rated power delivered to the shaft. A motors nameplate rating is based on output horsepower, which is ixed for continuous operation at full load. The amount of input power needed to produce rated horsepower will vary from motor to motor, with moreeficient motors requiring less input wattage than less-eficient models to produce the same output. Electrical energy input is measured in watts, while output is given in horsepower. Output power for motors may also be stated in watts or kilowatts. One horsepower is equivalent to 746 watts.

Energy Conservation Building Code (ECBC) User Guide

72

Electrical Power

As per the Code: Motors shall comply with the following: a. All permanently wired polyphase motors of 0.375 kW or more serving the building and expected to operate more than 1,500 hours per year and all permanently wired polyphase motors of 50kW or more serving the building and expected to operate more than 500 hours per year shall have a minimum acceptable nominal full load motor eficiency not less than IS 12615 for energy-eficient motors. (Refer Table 8.3, Table 8.4, Table 8.5, and Table 8.6.) b. Motors of horsepower differing from those listed in the table shall have eficiency greater than that of the next listed kW motor c. Motor horsepower ratings shall not exceed 20% of the calculated maximum load being served (Refer Box 8-C) d. Motor nameplates shall list the nominal full-load motor eficiencies and the full-load power factor e. Motor users should insist on proper rewinding practices for any rewound motors. If the proper rewinding practices cannot be assured, the damaged motor should be replaced with a new, eficient one rather than suffer the signiicant eficiency penalty associated with typical rewind practices (Refer Box 8-D for more information) f. Certiicates shall be obtained and kept on record indicating the motor eficiency. Whenever a motor is rewound, appropriate measures shall be taken so that the core characteristics of the motor is not lost due to thermal and mechanical stress during removal of damaged parts. After rewinding, a new eficiency test shall be performed and a similar record shall be maintained Table 8.3: Values of Performance Characteristic of Two Pole Energy-Eicient Induction Motors. Rated Output Frame Designation Full Load Speed
Min kW
(1) 0.37 0.55 0.75 1.1 1.5 2.2 3.7 5.5 7.5 9.3 11.0 15.0 18.5 22.0 30.0 37.0 45.0 55.0 75.0 90.0 (2) 71 71 80 80 90S 90L 100L 132S 132S 160M 160M 160M 160L 180M 200L 200L 225M 250M 280S 280M

Full Load Current

Max Amp
(4) 1.2 1.6 2.0 2.8 3.7 5.0 8.0 11.0 15.0 18.5 21.5 29.0 35.0 41.5 54.0 67.0 80.0 95.0 130.0 150.0

Breakaway Torque in Terms of Full Load Torque

Min

Breakaway Current in Terms of Full Current, Equal or Below

For eff 2

Nominal Eficiency

For eff 1 For eff 2 For eff 1 Percent

(7) 650 650 650 650 650 700 700 700 700 700 700 700 700 700 700 700 700 700 700 700

Rev/min
(3) 2790 2760 2780 2790 2800 2810 2820 2830 2840 2840 2860 2870 2880 2890 2900 2900 2955 2960 2970 2970

Percent
(5) 170.0 170.0 170.0 170.0 170.0 170.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0

Percent
(6) 600 600 600 600 600 650 650 650 650 650 650 650 650 650 650 650 650 650 650 650

Percent
(8) 66.0 70.0 73.0 76.2 78.5 81.0 84.0 85.7 87.0 87.7 88.4 89.4 90.0 90.5 91.4 92.0 92.5 93.0 93.6 93.9

Percent
(9) 70.2 74.0 77.0 82.8 84.1 85.6 87.5 88.6 89.5 90.0 90.5 91.3 91.8 92.2 92.9 93.3 93.7 94.0 94.6 95.0

Energy Conservation Building Code (ECBC) User Guide

73

Electrical Power

110.0 125.0 132.01) 160.01)

315S 315M 315M 315L

2980 2980 2980 2980

185.0 209.0 220.0 265.0

160.0 160.0 160.0 160.0

650 650 650 650

700 700 700 700

94.0 94.5 94.5 94.8

95.0 95.3 95.3 95.5

Note: Output to frame size relation is maintained in accordance with 1S 1231 for all motors, except those marked as 1), wherein the frame size indicated is preferred frame size. Source: IS 12615: 2004, Energy-Eficient Induction Motors --- Three-Phase Squirrel Cage (First Revision) Table 8.4: Values of Performance Characteristic of 4 Pole Energy-Eicient Induction Motors. Rated Output Frame Designation Full Load Speed
Min kW
(1) 0.37 0.55 0.75 1.1 1.5 2.2 3.7 5.5 7.5 9.3 11.0 15.0 18.5 22.0 30.0 37.0 45.0 55.0 75.0 90.0 110.0 125.0 132.01) 160.01) (2) 71 80 80 90S 90L 100L 112M 132S 132M 160M 160M 160L 180M 180L 200L 225S 225M 250M 280S 280M 315S 315M 315M 315L

Full Load Current

Max Amp
(4) 1.4 1.7 2.2 2.9 3.8 5.1 8.1 11.4 15.4 18.5 22.0 30.0 36.0 43.0 56.0 69.0 84.0 99.0 134.0 164.0 204.0 234.0 247.0 288.0.

Breakaway Breakaway Torque in Current in Terms Terms of Full of Full Current, Load Torque Equal or Below
Min

Nominal Eficiency

For eff 2 For eff 1 For eff 2 For eff 1 Rev/min

(3) 1330 1340 1360 1370 1380 1390 1410 1420 1430 1430 1440 1440 1440 1440 1450 1450 1460 1460 1470 1470 1480 1480 1480 1480

Percent
(5) 170.0 170.0 170.0 170.0 170.0 170.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0 160.0

Percent
(6) 550 550 550 550 550 600 600 600 600 600 600 600 600 600 600 650 600 600 600 600 600 600 600 600

Percent
(7) 600 600 600 600 600 700 700 700 700 700 700 700 700 700 700 700 700 700 700 700 700 700 700 700

Percent
(8) 66.0 70.0 73.0 76.2 78.5 81.0 84.0 85.7 87.0 87.7 88.4 89.4 90.0 90.5 91.4 92.0 92.5 93.0 93.6 93.9 94.4 94.7 94.7 95.0

Percent
(9) 73.0 78.0 82.5 83.8 85.0 86.4 88.3 89.2 90.1 90.5 91.0 91.8 92.2 92.6 93.2 93.6 93.9 94.2 94.7 95.0 95.2 95.5 95.5 95.8

Note: Output to frame size relation is maintained in accordance with IS 1231 for all motors, except those marked as 1), wherein the frame size indicated is preferred frame size. Source: IS 12615: 2004, Energy-Eficient Induction Motors --- Three-Phase Squirrel Cage (First Revision)

Energy Conservation Building Code (ECBC) User Guide

74

Electrical Power

Table 8.5: Values of Performance Characteristic of 6 Pole Energy-Eicient Induction Motors. Rated Output Frame Designation Full Load Speed
Min

Full Load Current

Max

Breakaway Torque in Terms of Full Load Torque

Min

Breakaway Current in Terms of Full Current, Equal or Below

For eff 2 For eff 1 Percent
(7) 600 600 600 600 600 700 700 700 700 700 700 700 700 700 700 700 700 700 700 700 700 700

Nominal Eficiency

For eff 2 Percent

(8) 65.0 68.0 71.0 74.0 76.0 79.0 82.5 84.5 86.0 87.0 87.5 88.5 89.5 90.0 91.0 91.5 92.0 92.5 93.0 93.3 93.5 93.8

For eff 1 Percent

(9) 69.4 72.0 74.6 77.3 79.6 82.2 85.1 86.8 88.1 89.3 89.7 90.5 91.3 91.8 92.6 93.0 93.4 93.8 94.2 94.5 94.6 94.9

kW
(1) 0.37 0.55 0.75 1.1 1.5 2.2 3.7 5.5 7.5 9.3 11.0 15.0 18.5 22.0 30.0 37.0 45.0 55.0 75.0 90.0 110.01) 132.01) (2) 80 80 90S 90L 100L 112M 132S 132M 160M 160L 160L 180L 200L 200L 225M 250M 280S 280M 315S 315M 315M 315L

Rev/min
(3) 870 870 890 900 900 910 920 920 930 930 935 940 940 945 945 950 960 960 970 970 970 980

Amp
(4) 1.4 1.9 2.3 3.2 4.0 5.5 8.8 12.7 16.7 20.5 23.0. 30.5 37.5 44.0 59.0 72.0 87.0 107.0 145.0 175.0 214.0 257.0

Percent
(5) 160.0 160.0 160.0 160.0 160.0 150.0 150.0 150.0 150.0 140.0 140.0 140.0 140.0 140.0 140.0 140.0 140.0 140.0 140.0 140.0 140.0 140.0

Percent
(6) 550 550 550 550 550 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600

Note: Output to frame size relation is maintained in accordance with IS 1231 for all motors, except those marked as 1), wherein the frame size indicated is preferred frame size. Source: IS 12615: 2004, Energy-Eficient Induction Motors --- Three-Phase Squirrel Cage (First Revision) Table 8.6: Values of Performance Characteristic of 8 Pole Energy-Eicient Induction Motors. Rated Output Frame Designation Full Load Speed
Min kW
(1) 0.37 0.55 0.75 (2) 90S 90L 100L

Full Load Current

Max Amp
(4) 1.5 2.1 2.7

Breakaway Torque in Terms of Full Load Torque

Min

Breakaway Current in Terms of Full Current, Equal or Below

For eff 2 For eff 1

Nominal Eficiency

For eff 2 For eff 1 Percent

(8) 62.0 67.0 70.0

Rev/min
(3) 640 640 650

Percent
(5) 150.0 150.0 150.0

Percent
(6) 550 550 550

Percent
(7) 600 600 600

Percent
(9) 66.8 71.1 73.8

Energy Conservation Building Code (ECBC) User Guide

75

Electrical Power

1.1 1.5 2.2 3.7 5.5 7.5 9.3 11.0 15.0 18.5 22.0 30.0 37.0 45.0 55.0 75.0 90.01) 110.01)

100L 112M I32S 160M 160M 160L 180L 180L 200L 225S 225M 250M 280S 280M 315S 315M 315L 315L

660 670 680 690 690 695 700 700 705 705 710 710 710 720 720 730 730 730

3.5 4.5 6.1 9.8 14.2 19.0 23.0 26.0 35.0 45.0 52.0 70.0 86.0 99.0 118.0 153.0 182.0 218.0

150.0 150.0 140.0 140.0 140.0 140.0 140.0 140.0 130.0 130.0 130.0 130.0 130.0 130.0 130.0 130.0 130.0 130.0

550 550 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600

600 600 700 700 700 700 700 700 600 700 700 700 700 700 700 700 700 700

72.0 74.0 77.0 80.0 82.5 84.0 85.0 86.0 87.0 88.0 88.5 90.0 90.5 91.0 91.5 92.3 92.8 93.3

76.2 77.9 80.5 83.0 85.1 86.4 87.3 88.1 89.0 89.8 90.2 91.5 90.5 92.4 92.8 93.5 93.9 94.3

Note: Output to frame size relation is maintained in accordance with 1S 1231 for all motors, except those marked as 1), wherein the frame size indicated is preferred frame size. Source: IS 12615: 2004, Energy-Eficient Induction Motors --- Three-Phase Squirrel Cage (First Revision)

Box 8-C: Consequences of Motor Over Sizing

When motors are oversized and operate for extended periods at signiicantly less than full load, there are three signiicant operational penalties reduced eficiency, reduced slip (important if the load is a cube-law type), and reduced power factor. Depending on the motor, eficiency will typically peak at somewhere between 75% load and full load. The larger the motor and the higher its peak eficiency, the more likely it will have a relatively lat eficiency curve between 50% load and full load, with a hump at 75% load some 0.3 to 1% points higher than at full load. Eficiency drops precipitously below 50% load, with the average 100-hp energyeficient motor losing over two points between 50 and 25% load and the average 100-hp standard eficiency induction motor dropping some 5.5 points over the same range. Smaller motors lose even more, particularly at lower eficiencies

A general rule-of-thumb is that a one percentage point increase in eficiency is equivalent to about a one-third-point increase in slip a decrease in slip can therefore quickly negate even a signiicant energy eficiency improvement (Figure 8.3)

Figure 8.3: Increase in eiciency (Percentage points)

Box 8-D: Motor Rewinding versus Replacement

Motor failures are frequently caused by bearing failures and are often accompanied by the breakdown of the coils of insulated wire inside the motor (the stator windings) and other problems. When a motor fails, the owner is faced with deciding whether to rebuild it or replace it. Rebuilding, commonly called rewinding, usually entails a lower initial cost compared to a replacement motor, especially for larger motors. Rewinding can preserve and, in rare cases, slightly improve motor eficiency if skillfully done. However, the rewinding process provides many avenues by which the motor eficiency can be degraded, greatly increasing operating cost and energy consumption.
Energy Conservation Building Code (ECBC) User Guide 76

Electrical Power

To ensure the highest quality in repaired motors, the consistent use of test equipment and documentation procedures must be integral parts of the repair process, so that the eficiency of the motor and the quality of its components can be veriied before the motor is put back into service. A critical task in most motor rebuilds is to remove the old windings without altering the adjacent laminated steel cores, and then to wrap new insulated wire around the old cores (Figure 8.4.)
Stator Core Back Iron Tooth Slot Air Gap Rotor Core Rotor Bar

Figure 8.4: Proile cutaway of an induction motor stator and rotor The old windings are commonly embedded in thick coats of varnish (used to glue the windings inside the core slots) which prevent their easy removal. Heat, chemicals, or mechanical force are commonly used to loosen and pull out old windings; excessive use of any of these can cause damage to the cores. Improper machining, replacement bearings, wire diameter, and winding technique can all compound, resulting in a rebuilt motor with poor performance and lower eficiency. Although it is technically possible to rebuild a motor to its original speciications, survey results of actual rewind practices show that this is seldom the case. On the average, rewound motors are less eficient than they were before rewinding. The magnitude of this problem can vary widely from one rewind shop to another, and can only be properly identiied when eficiency measurements are taken before and after rewinding. Source: E- Source Technology Atlas Series Volume IV, Drive Power

8.2.3

Power Factor Correction

As per the Code: All electricity supplies exceeding 100 A, 3 phases shall maintain their power factor between 0.95 lag and unity at the point of connection. Power factor correction is the process of adjusting the characteristics of electric loads in order to improve power factor so that it is closer to unity (i.e. 1). In simpliied, electrical terminology, power factor is the difference between real (kW) and reactive power (kVAR). It is a measure of how effectively current is being converted into useful work output and, more speciically, is a good indicator of the effect of the load current on the eficiency of the supply system. Power factor correction (PFC) may be applied either by an electrical power transmission utility to improve the stability and eficiency of the transmission network or, correction may be installed by individual electrical customers to, for example, reduce costs charged to them by their electricity supplier while simultaneously improving energy eficiency. A high power factor is generally desirable in a transmission system to reduce transmission losses and improve voltage regulation at the load. PFC is normally achieved by the addition of capacitors to the electrical network which reduce the burden on the supply. Box 8-E gives more information on the subject.

Box 8-E: Power Factor Correction

What are some of the beneits of Power Factor Correction? Reduced power consumption Reduced electricity bills Improved electrical energy eficiency Extra kVA availability from the existing supply Reduced I2R losses from transformer and distribution equipment

Energy Conservation Building Code (ECBC) User Guide

77

Electrical Power

Minimized voltage drop in long cables. What are some ways to correct the power factor? Minimize operation of idling or lightly loaded motors Avoid operation of equipment above its rated voltage Replace standard motors as they burn out with energy-eficient motors. Even with energy-eficient motors, however, the power factor is signiicantly affected by variations in load. A motor must be operated near its rated capacity to realize the beneits of a high power factor design. Install capacitors in your AC circuit to decrease the magnitude of reactive power.

8.2.4

Check-Metering and Monitoring

A signiicant barrier to achieving energy eficiency during the operation of a building is inadequate metering systems and monitoring plans. Building operators cannot be expected to manage energy if they cannot measure energy use. To improve a buildings energy performance over its operating life, and optimize the energy-eficient requirements, the Code requires that the buildings performance be measured. Metering is about having information that allows buildings energy managers to analyze and track changes in energy demand and, therefore, to manage their energy consumption more effectively. Energy metering is not a new concept and has been used by large energy-intensive buildings for many years to monitor energy consumption. The Code requires check-metering based on following three scenarios: a. Services exceeding 1000 kVA shall have permanently installed electrical metering to record demand (kVA), energy (kWh), and total power factor. The metering shall also display current (in each phase and the neutral), voltage (between phases and between each phase and neutral), and Total Harmonic Distortion (THD) as a percentage of total current b. Services not exceeding 1000 kVA but over 65 kVA shall have permanently installed electric metering to record demand (kW), energy (kWh), and total power factor (or kVARh) c. Services not exceeding 65 kVA shall have permanently installed electrical metering to record energy (kWh)

8.2.5

Power Distribution Systems

8.2.5.1 Power Distribution System Losses

As per the Code: The power cabling shall be adequately sized as to maintain the distribution losses not to exceed 1% of the total power usage. Record of design calculation for the losses shall be maintained. An engineer or contractor can demonstrate the real savings as well as the advantages of lower generated heat and increased lexibility of the installation with a properly sized distribution system. In addition, when less heat is generated, the result is reduced energy requirements for fans and air conditioning systems.

Energy Conservation Building Code (ECBC) User Guide

78

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

APPENDIX A: ECBC Deinitions, Abbreviations and Acronyms

9.1 General

ertain terms, abbreviations, and acronyms are deined in this section for the purposes of this code. These deinitions are applicable to all sections of this code. Terms that are not deined shall have their ordinarily accepted meanings within the context in which they are used. Websters Third New International Dictionary of the English Language, Unabridged, copyright 1986, shall be considered as providing ordinarily accepted meanings.

9.2 Deinitions
Addition: an extension or increase in loor area or height of a building outside of the existing building envelope Alteration: any change, rearrangement, replacement, or addition to a building or its systems and equipment; any modiication in construction or building equipment Annual fuel utilization eficiency (AFUE): an eficiency description of the ratio of annual output energy to annual input energy as developed in accordance with requirements of U.S. Department of Energy (DOE) 10CFR Part 430 Astronomical time switch: an automatic time switch that makes an adjustment for the length of the day as it varies over the year Authority having jurisdiction: the agency or agent responsible for enforcing this Code Automatic: self-acting, operating by its own mechanism when actuated by some non-manual inluence, such as a change in current strength, pressure, temperature, or mechanical coniguration. Automatic control device: a device capable of automatically turning loads off and on without manual intervention Balancing, air system: adjusting airlow rates through air distribution system devices, such as fans and diffusers, by manually adjusting the position of dampers, splitters vanes, extractors, etc., or by using automatic control devices, such as constant air volume or variable air volume boxes Balancing, hydronic system: adjusting water low rates through hydronic distribution system devices, such as pumps and coils, by manually adjusting the position valves, or by using automatic control devices, such as automatic low control valves Ballast: a device used in conjunction with an electric-discharge lamp to cause the lamp to start and operate under proper circuit conations of voltage, current, waveform, electrode heat, etc. Boiler: a self-contained low-pressure appliance for supplying steam or hot water Boiler, packaged: a boiler that is shipped complete with heating equipment, mechanical draft equipment, and automatic controls; usually shipped in one or more sections. A packaged boiler includes factory-built boilers manufactured as a unit or system, disassembled for shipment, and reassembled at the site. Building: a structure wholly or partially enclosed within exterior walls, or within exterior and party walls, and a roof, affording shelter to persons, animals, or property.

Energy Conservation Building Code (ECBC) User Guide

A.1

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

Building, existing: a building or portion thereof that was previously occupied or approved for occupancy by the Authority Having Jurisdiction Building complex: a group of buildings in a contiguous area under single ownership Building entrance: any doorway, set of doors, turnstiles, or other form of portal that is ordinarily used to gain access to the building by its users and occupants Building envelope: the exterior plus the semi-exterior portions of a building. For the purposes of determining building envelope requirements, the classiications are deined as follows: Building envelope, exterior: the elements of a building that separate conditioned spaces from the exterior Building envelope, semi-exterior: the elements of a building that separate conditioned space from unconditioned space or that enclose semi-heated spaces through which thermal energy may be transferred to or from the exterior, or to or from unconditioned spaces, or to or from conditioned spaces Building exit: any doorway, set of doors, or other form of portal that is ordinarily used only for emergency egress or convenience exit Building grounds lighting: lighting provided through a buildings electrical service for parking lot, site, roadway, pedestrian pathway, loading dock, and security applications Building material: any element of the building envelope through which heat lows and that heat is included in the component U-factor calculations other than air ilms and insulation Circuit breaker: a device designed to open and close a circuit by nonautomatic means and to open the circuit automatically at a predetermined over-current without damage to itself when properly applied within its rating Class of construction: for the building envelope, a subcategory of roof, wall, loor, slab-on-grade loor, opaque door, vertical fenestration, or skylight Coeficient Of Performance (COP) cooling: the ratio of the rate of heat removal to the rate of energy input, in consistent units, for a complete refrigerating system or some speciic portion of that system under designated operating conditions Coeficient Of Performance (COP) heating: the ratio of the rate of heat delivered to the rate of energy input, in consistent units, for a complete heat pump system, including the compressor and, if applicable, auxiliary heat, under designated operating conditions Commercial building: all buildings except for multi-family buildings of three stories or fewer above grade and single-family buildings Construction documents: drawings and speciications used to construct a building, building systems, or portions thereof Control: to regulate the operation of equipment Control device: a specialized device used to regulate the operation of equipment Constant Volume System: a space-conditioning system that delivers a ixed amount of air to each space. The volume of air is set during the system commissioning. Cool roof: a property of a surface that describes its ability to relect and reject heat. Cool roof surfaces have both a light color (high solar relectance) and a high emittance (can reject heat back to the environment) Daylighted area: the daylight illuminated loor area under horizontal fenestration (skylight) or adjacent to vertical fenestration (window), described as follows: Effective Aperture: Visible Light Transmittance x Window-to-Wall Ratio (EA = VLT x WWR).

Energy Conservation Building Code (ECBC) User Guide

A.2

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

Horizontal Fenestration: the area under a skylight, monitor, or sawtooth coniguration with an effective aperture greater than 0.001 (0.1%). The daylighted area is calculated as the horizontal dimension in each direction equal to the top aperture dimension in that direction plus either the loor-to-ceiling height (H) for skylights, or 1.5 H for monitors, or H or 2H for the sawtooth coniguration, or the distance to the nearest 1000 mm (42 in) or higher opaque partition, or one-half the distance to an adjacent skylight or vertical glazing, whichever is least, as shown in the plan and section igures below.

Vertical Fenestration: the loor area adjacent to side apertures (vertical fenestration in walls) with an effective aperture greater than 0.06 (6%). The daylighted area extends into the space perpendicular to the side aperture a distance either two times the head height of the side aperture or to the nearest 1.35 m (54 in) or higher opaque partition, whichever is less. In the direction parallel to the window, the daylighted area extends a horizontal dimension equal to the width of the window plus either 1 m (3.3 ft) on each side of the aperture, the distance to an opaque partition, or one-half the distance to an adjacent skylight or window, whichever is least.

Energy Conservation Building Code (ECBC) User Guide

A.3

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

Dead band: the range of values within which a sensed variable can vary without initiating a change in the controlled process Demand: the highest amount of power (average KW over an interval) recorded for a building or facility in a selected time frame Design capacity: output capacity of a system or piece of equipment at design conditions Design conditions: speciied environmental conditions, such as temperature and light intensity, required to be produced and maintained by a system and under which the system must operate Distribution system: a device or group of devices or other means by which the conductors of a circuit can be disconnected from their source of supply Door: all operable opening areas (which are not fenestration) in the building envelope, including swinging and rollup doors, ire doors, and access hatches. Doors that are more than one-half glass are considered fenestration. For the purposes of determining building envelope requirements, the classiications are deined as follows: Door, non-swinging: roll-up sliding, and all other doors that are not swinging doors. Door, swinging: all operable opaque panels with hinges on one side and opaque revolving doors. Door area: total area of the door measured using the rough opening and including the door slab and the frame. Dwelling unit: a single unit providing complete independent living facilities for one or more persons, including permanent provisions for living, sleeping, eating, cooking, and sanitation Economizer, air: a duct and damper arrangement and automatic control system that together allow a cooling system to supply outdoor air to reduce or eliminate the need for mechanical cooling during mild or cold weather Economizer, water: a system by which the supply air of a cooling system is cooled indirectly with water that is itself cooled by heat or mass transfer to the environment without the use of mechanical cooling Effective aperture: Visible Light Transmittance X Window-to-wall Ratio. (EA = VLT X WWR) Effective aperture, horizontal fenestration: a measure of the amount of daylight that enters a space through horizontal fenestration (skylights). It is the ratio of the skylight area times the visible light transmission divided by the gross roof area above the daylighted area. (See also daylighted area.) Effective aperture, vertical fenestration: a measure of the amount of daylight that enters a space through vertical fenestration. It is the ratio of the daylight window area times its visible light transmission plus half the vision glass area times its visible light transmission and the sum is divided by the gross wall area. Daylighted window area is located 2.2 m (7 ft) or more above the loor and vision window area is located above 1 m (3 ft) but below 2.2 m (7 ft). The window area, for the purposes of determining effective aperture shall not include windows located in light wells when the angle of obstruction () of objects obscuring the sky dome is greater than 70o, measured from the horizontal, nor shall it include window area located below a height of 1 m (3 ft). (See also daylighted area.) Eficacy: the lumens produced by a lamp/ballast system divided by the total watts of input power (including the ballast), expressed in lumens per watt Eficiency: performance at a speciied rating condition Remittance: the ratio of the radiant heat lux emitted by a specimen to that emitted by a blackbody at the same temperature and under the same conditions Enclosed building: a building that is totally enclosed by walls, loors, roofs, and openable devices such as doors and operable windows

Energy Conservation Building Code (ECBC) User Guide

A.4

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

Energy: the capacity for doing work. It takes a number of forms that may be transformed from one into another such as thermal (heat), mechanical (work), electrical, and chemical. Customary measurements are watts (W) Energy Eficiency Ratio (EER): performance of smaller chillers and rooftop units is frequently measured in EER rather than 1/ (kW/ton). It is the ratio of net cooling capacity in Btu/h to total rate of electric input in watts under designated operating conditions. The higher the EER, the more eficient the unit Energy Factor (EF): a measure of water heater overall eficiency Envelope performance factor: the trade-off value for the building envelope performance compliance option calculated using the procedures speciied in Section 12-Appendix D. For the purposes of determining building envelope requirements the classiications are deined as follows: Base envelope performance factor: the building envelope performance factor for the base design Proposed envelope performance factor: the building envelope performance factor for the Proposed Design Equipment: devices for comfort conditioned, electric power, lighting, transportation, or service water heating including, but not limited to, furnaces, boilers, air conditioners, heat pumps, chillers, water heaters, lamps, luminaries, ballasts, elevators, escalators, or other devices or installations Equipment, existing: equipment previously installed in an existing building Faade area: area of the faade, including overhanging sofits, cornices, and protruding columns, measured in elevation in a vertical plane, parallel to the plane of the face of the building. Non-horizontal roof surfaces shall be included in the calculations of vertical faade area by measuring the area in a plane parallel to the surface. Fan system power: the sum of the nominal power demand (nameplate W or HP) of motors of all fans that are required to operate at design conditions to supply air from the heating or cooling source to the conditioned space(s) and return it to the source of exhaust it to the outdoors. Fenestration: all areas (including the frames) in the building envelope that let in light, including windows, plastic panels, clerestories, skylights, glass doors that are more than one-half glass, and glass block walls. Skylight: a fenestration surface having a slope of less than 60 degrees from the horizontal plane. Other fenestration, even if mounted on the roof of a building, is considered vertical fenestration. Fenestration area: total area of the fenestration measured using the rough opening and including the glazing, sash, and frame. For doors where the glazed vision area is less than 50% of the door area, the fenestration area is the glazed vision area. For all other doors, the fenestration area is the door area. Floor area gross: the sum of the loor areas of the spaces within the building including basements, mezzanine and intermediate-loored tiers, and penthouses with headroom height of 2.5 m (7.5 ft) or greater. It is measured from the exterior faces of exterior walls or from the centerline of walls separating buildings, but excluding covered walkways, open roofed-over areas, porches and similar spaces, pipe trenches, exterior terraces or steps, chimneys, roof overhangs, and similar features. Gross building envelope loor area: the gross loor area of the building envelope, but excluding slab-ongrade loors. Gross conditioned loor area: the gross loor area of conditioned spaces. Gross lighted loor area: the gross loor area of lighted spaces. Gross semi heated loor area: the gross loor area of semi heated spaces. Flue damper: a device in the lue outlet or in the inlet of or upstream of the draft control device of an individual, automatically operated, fossil fuel-ired appliance that is designed to automatically open the lue outlet during appliance operation and to automatically close the lue outlet when then appliance is in standby condition.

Energy Conservation Building Code (ECBC) User Guide

A.5

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

Fossil fuel: fuel derived from a hydrocarbon deposit such as petroleum, coal, or natural gas derived from living matter of a previous geologic time. Fuel: a material that may be used to produce heat or generate power by combustion. Generally accepted engineer standard: a speciication, rule, guide, or procedure in the ield of engineering, or related thereto, recognized and accepted as authoritative. Grade: the inished ground level adjoining a building at all exterior walls. Guest room: any room or rooms used or intended to be used by a guest for sleeping purposes. Heat capacity: the amount of heat necessary to raise the temperature of a given mass 1C (1F). Numerically, the heat capacity per unit area of surface (W/m2K [Btu/ft2 -F]) is the sum of the products of the mass per unit area of each individual material in the roof, wall, or loor surface multiplied by its individual speciic heat. Heat Pump: A heat pump consists of one or more factory-made assemblies that normally include indoor conditioning coil, compressor, and outdoor coil, including means to provide a heating function. Heat pumps provide the function of air heating with controlled temperature, and may include the functions of air cooling, air circulation, air cleaning, dehumidifying, or humidifying. Heating Seasonal Performance Factor (HSPF): the total heating output of a heat pump during its normal annual usage period for heating (in Btu) divided by the total electric energy input during the same period. Historic: a building or space that has been speciically designed as historically signiicant. HVAC system: the equipment, distribution systems, and terminals that provide, either collectively or individually, the processes of heating, ventilating, or air conditioned to a building or portion of a building. Iniltration: the uncontrolled inward air leakage through cracks and crevices in any building element and around windows and doors of a building caused by pressure differences across these elements due to factors such as wind, inside and outside temperature differences (stack effect), and imbalance between supply and exhaust air systems. Installed interior lighting power: the power in watts of all permanently installed general, task, and furniture lighting systems and luminaires. Integrated part-load value: a single number igure of merit based on part-load EER, COP, or 1/ (kW/ ton) expressing part-load eficiency for air-conditioning and heat pump equipment on the basis of weighted operation at various load capacities for the equipment. Kilovolt-ampere: where the term kilovolt-ampere (kVA) is used in this Code, it is the product of the line current (amperes) times the nominal system voltage (kilovolts) times 1.732 for three-phase currents. For single-phase applications, kVA is the product of the line current (amperes) times the nominal system voltage (kilovolts). Kilowatt: the basic unit of electric power, equal to 1000 W. Labeled: equipment or materials to which a symbol or other identifying mark has been attached by the manufacturer indicating compliance with speciied standard or performance in a speciied manner. Lamp: a generic term for man-made light source often called bulb or tube. Lighted loor area, gross: the gross loor area of lighted spaces. Lighting, decorative: lighting that is purely ornamental and installed for aesthetic effect. Decorative lighting shall not include general lighting. Lighting, emergency: lighting that provides illumination only when there is a general lighting failure. Lighting, general: lighting that provides a substantially uniform level of illumination throughout an area.
Energy Conservation Building Code (ECBC) User Guide A.6

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

General lighting shall not include decorative lighting or lighting that provides a dissimilar level of illumination to serve a specialized application or feature within such area. Lighting Eficacy (LE): the quotient of the total lumens emitted from a lamp or lamp/ballast combination divided by the watts of input power, expressed in lumens per watt. Lighting system: a group of luminaires circuited or controlled to perform a speciic function. Lighting power allowance: Interior lighting power allowance: the maximum lighting power in watts allowed for the interior of a building Exterior lighting power allowance: the maximum lighting power in watts allowed for the exterior of a building Lighting Power Density (LPD): the maximum lighting power per unit of area of a building classiication of space function. Low-rise residential: single-family houses, multi-family structures of three stories or fewer above grade, manufactured houses (mobile homes), and manufactured houses (modular). Lumen: It is the unit of total light output from a light source. If a lamp or ixture were surrounded by a transparent bubble, the total light low through the bubble is measured in lumens. Lamps are rated in lumens, which is the total amount of light they emit, not their brightness and not the light level on a surface. Typical indoor lamps have light output ranging from 50 to 10,000 lumens. Lumen value is used for purchasing and comparing lamps and their outputs. Lumen output of a lamp is not related to the light distribution pattern of a lamp. Luminaries: a complete lighting unit consisting of a lamp or lamps together with the housing designed to distribute the light, position and protect the lamps, and connect the lamps to the power supply. Manual (non-automatic): requiring personal intervention for control. Non-automatic does not necessarily imply a manual controller, only that personal intervention is necessary. Manufacturer: the company engaged in the original production and assembly of products or equipment or a company that purchases such products and equipment manufactured in accordance with company speciications. Mean temperature: one-half the sum of the minimum daily temperature and maximum daily temperature. Mechanical cooling: reducing the temperature of a gas or liquid by using vapor compression, absorption, and desiccant dehumidiication combined with evaporative cooling, or another energy-driven thermodynamic cycle. Indirect of direct evaporative cooling alone is not considered mechanical cooling. Metering: instruments that measure electric voltage, current, power, etc. Multifamily high-rise: multifamily structures of four or more stories above grade Multifamily low-rise: multifamily structures of three or less stories above grade Multiplication factor: indicates the relative reduction in annual solar cooling load from overhangs and/or side ins with given projection factors, relative to the respective horizontal and vertical fenestration dimensions.

Energy Conservation Building Code (ECBC) User Guide

A.7

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

Non-automatic: See deinition of manual. Occupancy sensor: a device that detects the presence or absence of people within an area and causes lighting, equipment, or appliances to be regulated accordingly. Opaque: all areas in the building envelope, except fenestration and building service openings such as vents and grilles. Orientation: the direction an envelope element faces, i.e., the direction of a vector perpendicular to and pointing away from the surface outside of the element. For vertical fenestration, the two categories are northoriented and all other. Outdoor (outside) air: air that is outside the building envelope or is taken from the outside the building that has not been previously circulated through the building. Overcurrent: any current in excess of the rated current of the equipment of the capacity of the conductor. It may result from overload, short circuit, or ground fault. Packaged Terminal Air Conditioner (PTAC): a factory-selected wall sleeve and separate unencased combination of heating and cooling components, assemblies, or sections. It may include heating capability by hot water, steam, or electricity, and is intended for mounting through the wall to service a single room or zone. Party wall: a irewall on an interior lot line used or adapted for joint service between two buildings. Permanently installed: equipment that is ixed in place and is not portable or movable. Plenum: a compartment or chamber to which one or more ducts are connected, that forms a part of the air distribution system, and that is not used for occupancy or storage. A plenum often is formed in part or in total by portions for the building. Pool: any structure, basin, or tank containing an artiicial body of water for swimming, diving, or recreational bathing. The terms include, but are not limited to, swimming pool, whirlpool, spa, hot tub. Process load: the load on a building resulting from the consumption or release of process energy. Projection factor, overhang: the ratio of the horizontal depth of the external shading projection divided by the sum of the height of the fenestration and the distance from the top of the fenestration to the bottom of the farthest point of the external shading projection, in consistent units. Projection factor, sidein: the ratio of the horizontal depth of the external shading projection divided by the distance from the window jamb to the farthest point of the external shading projection, in consistent units. R-value (thermal resistance): the reciprocal of the time rate of heat low through a unit area induced by
Energy Conservation Building Code (ECBC) User Guide A.8

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

a unit temperature difference between two deined surfaces of material or construction under steady-state conditions. Units of R are m2K/W (hft2F/Btu). For the prescriptive building envelope option, R-value is for the insulation alone and does not include building materials or air ilms. Readily accessible: capable of being reached quickly for operation, renewal, or inspections without requiring those to whom ready access is requisite to climb over or remove obstacles or to resort to portable ladders, chairs, etc. In public facilities, accessibility may be limited to certiied personnel through locking covers or by placing equipment in locked rooms. Recirculating system: a domestic or service hot water distribution system that includes a close circulation circuit designed to maintain usage temperatures in hot water pipes near terminal devices (e.g., lavatory faucets, shower heads) in order to reduce the time required to obtain hot water when the terminal device valve is opened. The motive force for circulation is either natural (due to water density variations with temperature) or mechanical (recirculation pump). Relectance: the ratio of the light relected by a surface to the light incident upon it Resistance, electric: the property of an electric circuit or of any object used as part of an electric circuit that determines for a given circuit the rate at which electric energy is converted into heat or radiant energy and that has a value such that the product of the resistance and the square of the current gives the rate of conversion of energy Reset: automatic adjustment of the controller set point to a higher or lower value Residential: spaces in buildings used primarily for living and sleeping. Residential spaces include, but are not limited to, dwelling units, hotel/motel guest rooms, dormitories, nursing homes, patient rooms in hospitals, lodging houses, fraternity/sorority houses, hostels, prisons, and ire stations. Return Air: air from the conditioned area that is returned to the conditioning equipment for reconditioning. The air may return to the system through a series of ducts, plenums, and airshafts. Roof: the upper portion of the building envelope, including opaque areas and fenestration, that is horizontal or tilted at an angle of less than 60 from horizontal Roof area, gross: the area of the roof measured from the exterior faces of walls or from the centerline of party walls Service: the equipment for delivering energy from the supply or distribution system to the premises served Service water heating: heating water for domestic or commercial purposes other than space heating and process requirements Set point: point at which the desired temperature (C) of the heated or cooled space is set Shading Coeficient (SC): the ratio of solar heat gain at normal incidence through glazing to that occurring through 3 mm (1/8 in) thick clear, double-strength glass. Shading coeficient, as used herein, does not include interior, exterior, or integral shading devices Simulation program: a computer program that is capable of simulating the energy performance of building systems Single-zone system: an HVAC system serving a single HVAC zone Site-recovered energy: waste energy recovered at the building site that is used to offset consumption of purchased fuel or electrical energy supplies Skylight roof ratio (SRR): the ratio of the total skylight area of the roof, measured to the outside of the frame, to the gross exterior roof.

Energy Conservation Building Code (ECBC) User Guide

A.9

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

Slab-on-grade loor: that portion of a slab loor of the building envelope that is in contact with ground and that is either above grade or is less than or equal to 24 in below the inal elevation of the nearest exterior grade Solar energy source: source of thermal, chemical, or electrical energy derived from direction conversion of incident solar radiation at the building site. Solar Heat Gain Coeficient (SHGC): the ratio of the solar heat gain entering the space through the fenestration area to the incident solar radiation, typically ranging from 0.9 to 0.1, where lower values indicate lower solar gain. Solar heat gain includes directly transmitted solar heat and absorbed solar radiation, which is then reradiated, conducted, or convected into the space. Space: an enclosed space within a building. The classiications of spaces are as follows for the purpose of determining building envelope requirements. Conditioned space: a cooled space, heated space, or directly conditioned space. Semi-heated space: an enclosed space within a building that is heated by a heating system whose output capacity is greater or equal to 10.7 W/m2 (3.4 Btu/h-ft2) of loor area but is not a conditioned space. Enclosed Space: space within a building that is not conditioned space or a semi-heated space. Crawlspaces, attics, and parking garages with natural or mechanical ventilation are not considered enclosed spaces. Standard Design: a computer representation of a hypothetical design based on the actual Proposed Design as per Appendix B Whole Building Performance Method Story: portion of a building that is between one inished loor level and the next higher inished loor level or the roof, provided, however, that a basement or cellar shall not be considered a story. Supply Air: air being conveyed to a conditioned area through ducts or plenums from a heat exchanger of a heating, cooling, absorption, or evaporative cooling system. Supply air is commonly considered air delivered to a space by a space-conditioning system. Depending on space requirements, the supply may be either heated, cooled or neutral. System: a combination of equipment and auxiliary devices (e.g., controls, accessories, interconnecting means, and terminal elements) by which energy is transformed so it performs a speciic function such as HVAC, service water heating, or lighting. System, existing: a system or systems previously installed in an existing building. Terminal: a device by which energy form a system is inally delivered, e.g., registers, diffusers, lighting ixtures, faucets, etc. Thermal block: a collection of one or more HVAC zones grouped together for simulation purposes. Spaces need not be contiguous to be combined within a single thermal block. Thermal Zone: a term used in energy simulation to represent area catered to by one air conditioning unit. With the help of the zoning building plans are simpliied to reduce the modelers work. Normally, within one zone usage pattern, set point temperature and other conditions are identical. Building spaces that would experience similar heating and cooling loads are generally grouped under one zone. Thermostat: an automatic control device used to maintain temperature at a ixed or adjustable set point. Tinted: (as applied to fenestration) bronze, green, or grey coloring that is integral with the glazing material. Tinting does not include surface applied ilms such as relective coatings, applied either in the ield or during the manufacturing process. Ton: one ton of cooling is the amount of heat absorbed by one ton of ice melting in one day, which is equivalent to 3.5136 KW or 3.516 thermal kW.

Energy Conservation Building Code (ECBC) User Guide

A.10

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

Transformer: a piece of electrical equipment used to convert electric power from one voltage to another voltage. U-factor (Thermal Transmittance): heat transmission in unit time through unit area of a material or construction and the boundary air ilms, induced by unit temperature difference between the environments on each side. Units of U are W/m2 -C (Btu/h ft2 F). Variable Air Volume (VAV) system: HVAC system that controls the dry-bulb temperature within a space by varying the volumetric low of heated or cooled supply air to the space Vent damper: a device intended for installation in the venting system or an individual, automatically operated, fossil fuel-ired appliance in the outlet or downstream of the appliance draft control device, which is designed to automatically open the venting system when the appliance is in operation and to automatically close off the venting system when the appliance is in standby or shutdown condition. Ventilation: the process of supplying or removing air by natural or mechanical means to or from any space. Such air is not required to have been conditioned. Visible Light Transmittance (VLT): also known as the Visible Transmittance, is an optical property of a light transmitting material (e.g. window glazing, translucent sheet, etc.) that indicates the amount of visible light transmitted of the total incident light. Wall: that portion of the building envelope, including opaque area and fenestration, that is vertical or tilted at an angle of 60 from horizontal or greater. This includes above and below-grade walls, between loor spandrels, peripheral edges of loors, and foundation walls. Wall, above grade: a wall that is not below grade Wall, below grade: that portion of a wall in the building envelope that is entirely below the inish grade and in contact with the ground Wall area, gross: the overall area off a wall including openings such as windows and doors, measured horizontally from outside surface to outside service and measured vertically from the top of the loor to the top of the roof. If roof insulation is installed at the ceiling level rather than the roof, then the vertical measurement is made to the top of the ceiling. (Note that does not allow roof insulation to be located on a suspended ceiling with removable ceiling panels.) The gross wall area includes the area between the ceiling and the loor for multistory buildings.

Water heater: vessel in which water is heated and is withdrawn for use external to the system. Weather stripping: Materials, such as a strip of fabric, plastic, rubber or metal, or a device used to seal the openings, gaps or cracks of venting window and door units to prevent water and air iniltration.

Energy Conservation Building Code (ECBC) User Guide

A.11

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

Window Wall Ratio (WWR): the ratio of vertical fenestration area to gross exterior wall area. Gross exterior wall area is measured horizontally from the exterior surface; it is measured vertically from the top of the loor to the bottom of the roof.

Zone, HVAC: A space or group of spaces within a building with heating and cooling requirements that are suficiently similar so that desired conditions (e.g., temperature) can be maintained throughout using a single sensor (e.g., thermostat or temperature sensor).

9.3 Abbreviations and Acronyms

AFUE ANSI ARI ASHRAE ASTM BIS Btu Btu/h Btu/ft2 F Btu/h ft2 Btu/h ft F Btu/h ft 2 F C cfm cm COP DOE EER Annual fuel utilization eficiency American National Standards Institute Air-Conditioning and Refrigeration Institute American Society of Heating, Refrigerating and Air-Conditioning Engineers American Society for Testing and Materials Bureau of Indian Standards British thermal unit British thermal units per hour British thermal units per square foot per degree Fahrenheit British thermal units per hour per square foot British thermal units per lineal foot per degree Fahrenheit British thermal units per hour per square foot per degree Fahrenheit Celsius Cubic feet per minute Centimeter Coeficient of Performance Department of Energy, U.S. Energy Eficiency Ratio
A.12

Energy Conservation Building Code (ECBC) User Guide

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

EC Act 2001 EF F ft h HC h ft2 F/Btu h m2K/W hp HSPF HVAC I-P in. IPLV ISHRAE kVA kW kWh LE lin lin ft lin m lm LPD m mm NAECA PF PTAC R SC SHGC SL

Energy Conservation Act 2001 Energy Factor Fahrenheit Foot Hour Heat capacity Hour per square foot per degree Fahrenheit per British thermal unit Hour per square meter per degree Celsius per Watt Horsepower Heating seasonal performance factor Heating, Ventilation, and Air Conditioning Inch-pound Inch Integrated part-load value Indian Society of Heating, Refrigeration and Air-conditioning Engineers Kilovolt-ampere kilowatt kilowatt-hour Lighting eficacy Linear Linear foot Linear meter Lumen Lighting Power Density Meter Millimeter National Appliance Energy Conservation Act Projection factor Packaged terminal air conditioner R-value (thermal resistance) Shading Coeficient Solar heat gain coeficient Standby loss

Energy Conservation Building Code (ECBC) User Guide

A.13

Appendix A: ECBC Deinitions, Abbreviations and Acronyms

VAV VLT W W/ft2 W/m 2 W/m 2K W/m 2 W/mK W/m 2K Wh

Variable air volume Visible light transmission Watt Watts per square feet Watts per square meter Watts per square meter per degree Celsius Watts per hour per square meter Watts per lineal meter per degree Celsius Watts per hour per square meter per degree Celsius Watthour

Energy Conservation Building Code (ECBC) User Guide

A.14

Appendix B: Whole Building Performance Method

APPENDIX B: Whole Building Performance Method1

10.1 General
hole building energy simulation analysis is used to predict the annual energy performance of a building design. The analysis is carried out by irst developing a detailed building energy simulation model. The simulation program is then used to test the thermal response, and to calculate the energy use of the building model using a weather data ile to capture the climatic impact on the building. This type of analysis is referred to as the Whole Building Performance (WBP) method.

Beneits Whole building energy simulation is currently the most sophisticated way of analyzing the impact of energy eficiency measures in an integrated manner. It is an alternative to the prescriptive requirements contained in 4 to 8 of ECBC. The impact of changing any one of the myriad parameters affecting energy performance of the building design being modeled can be predicted using this method. This is particularly useful for studying the impact of combinations of energy eficiency measures that may lead to non-linear building energy outcomes. For example, electric lights produce light and heat inside a space. Calculating the electrical consumption for the electric lights is not very dificult, as long as one knows how many lights there are, what their heat output is, and how many hours they run. One does not need a simulation model to predict this outcome. However, the heat generated by electric lighting has to be removed by the HVAC systems in a warm or hot climate. Calculating the reduction in energy used by the HVAC systems due to the use of a more eficient electric lighting system is not recommended through manual calculations. This computation becomes signiicantly more complex if the design team decides to employ a daylight linked electric lighting system. Such a system is designed to reduce light (and heat output) in a space when enough daylight is available. This non-linear relationship impacts the electric energy input to the lighting system, and the heat removed by the HVAC system. At this time, predicting the integrated energy performance resulting from complex energy eficiency strategies cannot be studied reliably by any other means except the use of a whole building energy simulation analysis. Once the model is completed and a base run is established, carrying out multiple runs to test alternate design options involves less effort on the part of the analyst, although there could still be substantial computer run time involved. Whole building energy simulation is increasingly being used for testing compliance with various building energy codes and sustainability rating tools such as LEED and GRIHA. Technically reliable and veriiable energy simulation programs satisfying the minimum modeling capabilities (speciied in 10.2.1) should be used for compliance using this veriication method.

10.1.1 Scope
In general, the WBP method may be used to show compliance with the ECBC for any project at the designers discretion, subject to the following caveats and exceptions. No HVAC System Use of the WBP method requires knowledge of the proposed HVAC system in order to create the Standard Design. Buildings with no HVAC system cannot use the WBP Method. In the case of a shell building, which might become conditioned in the future, trade-offs may still be made within the envelope system.

This chapter has been adapted from Appendix G and ECB chapter of ASHRAE User Manual

Energy Conservation Building Code (ECBC) User Guide

B.1

Appendix B: Whole Building Performance Method

Alterations to Existing Buildings When the WBP method is used for an alteration of an existing building, some special rules apply. The WBP method is optional for this purpose; designers may use the calculation acceptable to the Authority Having Jurisdiction. Unless a building component is being altered, the Proposed Design and the Standard Design are identical for that component. Portions of the building that are being replaced shall be treated as new systems and these systems in the Standard Design shall be representative of the requirements in the ECBC. Alterations and Additions The basic rules for alterations and additions are discussed in the Administration and Enforcement Section (3) of the ECBC User Guide. There are some more rules that apply to cases where it is undesirable either to treat the addition as a stand-alone building or to fully model the entire existing building. It is often necessary with additions or alterations to model at least part of the existing building. For instance, if the existing buildings HVAC system is being extended to serve the new construction, then that system needs to be fully modeled in order to account for its energy performance. If, however, this system only serves a portion of the existing building and only part of that building is affected by the new work, then it is not necessary to model the entire existing building. Parts of Existing Buildings The rules for excluding parts of the existing building are as follows: If there is new construction that comes under the ECBC scope and it is part of the existing building but will be excluded from the Proposed Design, then those parts must comply with the Codes applicable prescriptive requirements. The excluded parts of the existing building must be served by HVAC systems that are completely independent of the systems or building components being modeled for the Proposed Building. There should not be any signiicant energy lows between the excluded parts of the building and the modeled parts. Rephrasing, the design space temperature, HVAC system operating set points, and operating and occupancy schedules on both sides of the boundary between the included and excluded parts must be the same. If the excluded portion of the building is a refrigerated warehouse and the included portion is an ofice, this condition would not be met, because there would be signiicant energy lows between them.

10.1.2 Compliance
Compliance of the Proposed Design with the requirements of the ECBC Whole Building Performance Method consists of the following steps: Developing a Standard Design simulation model Carrying out a valid energy simulation run using the Standard Design to predict its annual energy use Developing the Proposed Design simulation model for which compliance is being sought Carrying out a valid energy simulation run for the Proposed Design model and ensuring that the predicted annual energy use is less than or equal to the energy use in Standard Design The major consideration for generating the Standard Design simulation model is that it complies with the minimum performance requirements speciied in the ECBC. Much of the remainder of this chapter is addressed towards the development of the Standard and Proposed Designs. The following sections describe how decisions are to be taken for each of the two designs, and how these two simulation runs are to be done, but the following rules always apply: Mandatory provisions of the Code mentioned in 4 through section 8 are met Both simulation runs must use the same simulation program
Energy Conservation Building Code (ECBC) User Guide B.2

Appendix B: Whole Building Performance Method

Both simulation runs must use the same climate data Both simulation runs must use the same schedules of operation These rules ensure a fair comparison between the two runs, without introducing extraneous differences. For instance, if the runs used different simulation programs, then some portion of the differences between the resulting energy consumption would be due to differences in algorithms or calculation methodologies making it dificult to evaluate the impact of the two designs on energy use. The WBP method provides the building owner and design team with the lexibility to try out different design options, provided the end result is a building that does not have higher annual energy consumption than if it would have met all the prescriptive requirements. For example, the owner may decide to invest in a more eficient lighting system in place of larger glazing areas or invest in high performance glazing to avoid the cost of installing an economizer and get the beneits of daylighting.

10.1.3 Annual Energy Use

Annual energy use for the purposes of the whole building performance method shall be calculated in kilowatthours (kWh) of electricity use per year. Energy sources other than electricity which are used in the building shall be converted to kWh of electric energy at the rate of 0.75 kWh per mega Joule.

10.1.4 Trade-ofs Limited to Building Permit

The whole building performance method may be used for building permit applications that include less than the whole building; however, any design parameters that are not part of the building permit application shall be identical for both the Proposed Design and the Standard Design. Future improvements to the building shall comply with both the mandatory and prescriptive requirements.

10.1.5 Documentation Requirements

Compliance shall be documented and submitted to the Authority Having Jurisdiction. The information submitted shall include the following: a. The annual energy use for the Proposed Design and the Standard Design. b. A list of the energy-related building features in the Proposed Design that is different from the Standard Design. c. The input and output report (s) from the simulation program including a breakdown of energy usage by at least the following components: lights, internal equipment loads, service water heating equipment, space heating equipment, space cooling and heat rejection equipment, fans, and other HVAC equipment (such as pumps). The output reports shall also show the amount of time any loads are not met by the HVAC system for both the Proposed Design and Standard Design.2 d. An explanation of any error messages noted in the simulation program output.

10.2 Simulation General Requirements

10.2.1 Energy Simulation Program
WBP method uses the output of a simulation program to demonstrate that the Proposed Design complies with the ECBC. In order to make sure that these calculations are suficiently accurate for the purposes of the Code, a series of requirements have been set. The most basic requirement is that the simulation program be a computerbased program designed to analyze energy consumption in buildings, and that it has the capability to model the Proposed Designs features. A building energy simulation model comprises of: Detailed description of the building geometry and materials of construction
2 In order to show compliance using WBP method, WBP compliance forms (included in Appendix G) must be completed and submitted.

Energy Conservation Building Code (ECBC) User Guide

B.3

Appendix B: Whole Building Performance Method

Description of the internal loads in the building, e.g., lighting, equipment and people Description of the environmental control systems that operate to maintain comfortable conditions Description of schedules and controls to characterize the internal loads and environmental control systems

a) Building Model
Much of the effort in developing the model for an energy simulation analysis is in describing building geometry. This includes Describing the overall building envelope and geometry, ie., number of loors, orientation Describing physical and thermal properties for the construction of each building element Describing the location, size and the thermal, optical and solar properties of windows Describing permanent shading devices attached to the building, automatic window blinds and details of their operation Describing objects that might cast shadow on the building being simulated, e.g., surrounding buildings Describing spaces or thermal zones and their relative location, and relationship with the HVAC system design for the building

b) Minimum Modeling Capabilities

This deines the minimum set of capabilities for WBP method simulation programs. These have been broadly deined to allow all complying programs to be considered for approval by the Authority Having Jurisdiction, while eliminating programs that would not be able to adequately account for the energy performance of building features important under the Code. These minimum capabilities are: Approved Simulation Program: The simulation program should be subjected to the International Energy Agency BESTEST (Building Energy Simulation Test and Diagnostic Method) or the ANSI/ ASHRAE Standard 140-2004, Standard Method of Test for the Evaluation of Building Energy Analysis Computer Programs. Minimum Hours per Year: Programs must be able to model energy lows on an hourly basis for the entire year (8,760 hours). Hourly Variations: Building loads and system operations vary hour-by-hour, and their interactions have a great inluence on building energy performance. Approved programs must have the capability to model hourly variations and to establish separately designed schedules of operation for each day of the week and for holidays for occupancy, lighting power, miscellaneous equipment power, thermostat set points, and HVAC system operation. Thermal Mass Effects: A buildings ability to absorb and hold heat varies with the type of construction and with the system and ventilation characteristics. This affects the timing and magnitude of loads handled by the HVAC system. Simulation programs must be able to model these thermal mass effects. Number of Thermal Zones: There are multiple thermal zones in all but the simplest buildings, and they experience different load patterns. Approved programs must be able to model at least 10 thermal zones; many simulation programs can handle far greater number of zones. Part-Load Performance: Mechanical equipment seldom experiences full-load operating conditions, so the performance of this equipment under part-load conditions is important. Approved programs must incorporate part-load performance curves in their calculations. Correction Curves: The eficiency of the mechanical equipment varies depending on temperature and humidity conditions. Approved programs must incorporate eficiency correction curves for mechanical heating and cooling equipment.

Energy Conservation Building Code (ECBC) User Guide

B.4

Appendix B: Whole Building Performance Method

Economizers: Economizer cooling is an important eficiency measure under the Standard. Approved programs must have the capability to model both airside and waterside economizers with integrated control. Design Load Calculations: Approved programs must be capable of performing design load calculations to determine required HVAC equipment capacities and air and water low rates for both the Proposed Design and the Standard Design. This is to ensure that the systems in both design simulations are properly sized, which avoids the problem of differing part-load performance characteristics between the two designs.

c) Modeling Exceptions
All the energy systems of the Proposed Design must be modeled. The Standard Design, however, does have some exceptions that may be applied only in rare, special cases. It is allowable to exclude some components or systems of the Proposed Design provided they do not affect the energy usage of the other systems being modeled for trade-off purposes. For example, if the service hot water heating system is not located in the conditioned space, and if it is not generating signiicant heat gains that affect the HVAC system, then it may be ignored in the model. All systems that are excluded on this basis, however, must still meet the prescriptive requirements that apply to them. This exception can help to simplify the modeling somewhat, but only in ways that will not affect the accuracy of the WBP method calculations.

d) Limitations of the Simulation Program

There may also be cases where the simulation program lacks modeling capabilities needed to fully model a component or system of the Proposed Design. If this means that a reasonable calculation of the proposed building cannot be made, then the best solution is to seek a different program that has the needed capabilities. One alternative is to ignore the system in the model, provided this does not affect the modeling of energy consumption measures, described in the previous section. A second alternative is to apply engineering judgment and to model the component or system using a thermodynamically similar model that is within the capabilities of the program being used. This requires a thorough understanding of the algorithms of the simulation program and the thermodynamic characteristics of the component being modeled, but in many cases, it can be accomplished without compromising accuracy. It makes little sense, though, to use an alternate program for a component if it means losing the interactive capabilities of the hourly modeling tool. Consequently, this is generally not recommended. A third alternative is to simply model the system or component as if it were the base case system deined for the Standard Design. Of course, this alternative is only allowable when the system or component meets the prescriptive requirements of the ECBC. Also, this alternative is not preferred, as the intent is to model the actual Proposed Design. The general rule, therefore, is if a simulation program cant model a component, then the component must not be given any energy saving beneits.

10.2.2 Climate Data Requirements

A reference climate data ile for the location being tested or a prescribed equivalent should be used for the analysis. The ISHRAE database of weather iles developed for energy simulation is the primary dataset for this type of analysis.

10.2.3 Compliance Calculations

a) On-Site Renewable or Site-Recovered Energy
There is a special case for calculating the design energy consumption for buildings that have on-site renewable energy sources or site recovered energy. For example, a building may have a solar thermal array, photovoltaic panels, a geothermal energy source, or a building with substantial refrigeration loads may recover heat from the condenser to meet service water heating loads. If either renewable or recovered energy is available at the site, it is considered free energy by the WBP method, and that energy is not included in the design energy consumption, provided that it is not required by any of the prescriptive requirements in ECBC. For the Standard Design calculations, the loads met by renewable or recovered energy are considered to be served by the backup

Energy Conservation Building Code (ECBC) User Guide

B.5

Appendix B: Whole Building Performance Method

energy source. For example, where recovered energy is used to heat water, then the backup water heater would be assumed to supply all the hot water for the Standard Design, and that would be part of the Standard Design method. If no backup energy source is speciied for the Proposed Design, then the source is assumed to be electricity in the Standard Design.

b) Exceptional Calculation Method

As newer technologies become available, there may be cases where none of the existing simulation programs can adequately model the energy performance of these technologies. The WBP method allows users to use exceptional calculations, provided the nature of the exceptional method is open-ended; however, the burden is on the applicant to demonstrate that the method is reasonable, accurate, well founded, and not in contradiction with the rules of the WBP Method. The applicant must describe the theoretical basis for the exceptional method and must provide empirical evidence that the method accurately represents the energy performance of the design, material, or device.

c) Disclaimer
It is important for users of the WBP method, as well as the owners of the proposed buildings, to understand the WBP Methods intent and limitations. It is intended to provide a fair method of comparison between the estimated annual energy consumption of the Proposed Design and the Standard Design for purposes of compliance with the Code. The WBP Method is not intended to provide the most accurate prediction of actual energy consumption for the building as it is actually built. Although the designer is expected to model the future use of the building as closely as possible, there are many reasons why the actual building performance may differ from the design energy consumption. These include: Variations in Operation and Occupancy: The actual schedules of operation and occupancy may differ from those assumed in the WBP analysis. Variations in Control and Maintenance: The buildings energy systems may be controlled differently than assumed; the equipment may not be set up or maintained properly. Variations in Weather: The simulation runs use weather data that may not match the actual weather conditions; further, there is variability in weather conditions from year-to-year. Energy Uses not Included: The WBP method under certain conditions, may not require all building energy uses to be included in calculating the design energy consumption. Sometimes, there is additional energy-using equipment that is added to a building after it is built. Precision of the Simulation Program: Even the most sophisticated simulation programs approximate the actual energy lows and consumption in a building; further, the energy analyst will usually make simplifying assumptions. Both can be sources of error in the predictions of energy consumption.

10.3 Calculating the Energy Consumption of the Proposed Design and the Standard Design
10.3.1 The simulation model for calculating the Proposed Design and the Standard Design shall be developed in accordance with the requirements in Table 10.1

Energy Conservation Building Code (ECBC) User Guide

B.6

Table 10.1: Modeling Requirements for Calculating Proposed and Standard Design3 Proposed Design Standard Design as described in this table. Except as speciically instructed in this table, all building systems and equipment shall be modeled identically in the Standard Designs and Proposed Design.

Case

Design Model (a) The simulation model of the Proposed Design shall be consistent with the design The Standard Designs shall be developed by modifying the Proposed Design

Energy Conservation Building Code (ECBC) User Guide

documents, including proper accounting of fenestration and opaque envelope types and area; interior lighting power and controls; HVAC system types, sizes, and controls; and service water heating systems and controls. (b) When the whole building performance method is applied to buildings in which energyrelated features have not yet been designed (e.g., a lighting system), those yet-to-bedesigned features shall be described in the Proposed Design so that they minimally comply with applicable mandatory and prescriptive requirements from 4 through 8. (c) All conditioned spaces in the Proposed Design shall be simulated as being both heated and cooled even if no heating or cooling system is to be installed, and temperature and humidity control set points and schedules shall be the same for Proposed and Standard Designs. (d) All unconditioned and naturally ventilated occupied spaces in the Proposed Design shall be simulated and temperature and humidity control set points shall be speciied per National Building Code (2005) or ASHRAE 55 (2004).

Additions and Alterations

It is acceptable to predict performance using building models that exclude parts of the existing building provided that all of the following conditions are met: (a) Work to be performed in excluded parts of the building shall meet the requirements of 4 through 8. (b) Excluded parts of the building are served by HVAC systems that are entirely separate from those serving parts of the building that are included in the building model. (c) Design space temperature and HVAC system operating set points and schedules on either side of the boundary between included and excluded parts of the building are essentially the same.

Same as Proposed Design.

Space Use Classiication Schedules

The building type or space type classiications shall be chosen in accordance with 7.3.2 or 7.3.3. More than one building type category may be used in a building if it is a mixed-use facility.

Same as Proposed Design Same as Proposed Design.

Schedules capable of modeling hourly variations in occupancy, lighting power, miscellaneous equipment power, thermostat set points, and HVAC system operation shall be used. The schedules shall be typical of the proposed building type as determined and approved by the Authority Having Jurisdiction. HVAC Fan Schedules that provides outdoor air for ventilation shall run continuously whenever spaces are occupied and shall be cycled on and off to meet heating and cooling loads during unoccupied hours. Exceptions: (a) Where no heating and/or cooling system is to be installed and a heating or cooling system is being simulated only to meet the requirements described in this table, heating and/or cooling system fans shall not be simulated as running continuously during occupied hours but shall be cycled on and off to meet heating and cooling loads during all hours.

Appendix B: Whole Building Performance Method

(b) HVAC fans shall remain on during occupied and unoccupied hours in spaces that have health and safety mandated minimum ventilation requirements during unoccupied hours.

B.7

The table has been enhance to provide additional details to develop Standard and Proposed Design.

Appendix B: Whole Building Performance Method

Energy Conservation Building Code (ECBC) User Guide Lighting power in the Standard Designs shall be determined using the same categorization procedure (building area or space function) and categories as the Proposed Design with lighting power set equal to the maximum allowed for the corresponding method and category in either 7.3.2 or 7.3.3. Power for ixtures not included in the lighting power density calculation shall be modeled identically in the Proposed and Standard Design. No automatic lighting controls (e.g. programmable or automatic controls for daylight utilization) shall be modeled in the Standard Design, as the lighting schedules used are understood to relect the mandatory control requirements in the Code.

Building Envelope

All components of the building envelope in the Proposed Design shall be modeled as The Standard Designs shall have identical conditioned loor area and identical exterior dimensions and orientations as the Proposed Design, except as noted below. shown on architectural drawings or as installed for existing building envelopes. (a) Orientation: The standard building performance shall be generated by simulating the building Exceptions: The following building elements are permitted to differ from architectural with its actual orientation and again after rotating the entire building 90, 180, 270 degrees, then drawings. averaging the results. The building shall be modeled so that it does not shade itself. Opaque (a) Any envelope assembly that covers less than 5% of the total area of that assembly assemblies such as roof, loors, doors, and walls shall be modeled as having the same heat type (e.g., exterior walls) need not be separately described. If not separately decapacity as the Proposed Design and U-factor comply with requirements of 4.3.1 and 4.3.2. scribed, the area of an envelope assembly must be added to the area of the adjacent (b) Fenestration areas shall equal that in the Proposed Design or 40% of gross above grade wall assembly of that same type. area, whichever is smaller, and shall be distributed uniformly in horizontal bands across the four orientations. No shading projections are to be modeled; fenestration shall be (b) Exterior surfaces whose azimuth orientation and tilt differ by no more than 45 assumed to be lush with the exterior wall or roof. Manually operated fenestration shading degrees and are otherwise the same may be described as either a single surface or devices such as blinds or shades shall not be modeled. Fenestration U-factor shall comply by using multipliers. with Table 4.3, and the SHGC shall comply with Table 4.3 and 4.4 of the Code. (c) For exterior roofs other than roofs with ventilated attics, the relectance and emit- (c) Roof Albedo: All roof surfaces shall be modeled with a relectivity of 0.30. tance of the roof surface shall be modeled. For exterior roofs, the roof surface may (d) Skylights: Skylight area shall be equal to that in the Proposed Design or 5% of the gross be modeled with a relectance of 0.45 if the relectance of the Proposed Design roof roof area that is part of the building envelope, whichever is smaller. If the skylight is greater than 0.70 and its emittance is greater than 0.75. All other roof surfaces area of the Proposed Design is greater than 5% of the gross roof area, baseline skylight shall be modeled with a relectance of 0.30.The relectance and emittance shall be area shall be decreased by an identical percentage in all roof components in which tested in accordance with 4.3.1.1. skylights are located to reach the 5% skylight-to-roof ratio. Skylight orientation and tilt shall be the same as in the Proposed Design. Skylight U-factor and SHGC properties (d) Manually operated fenestration shading devices such as blinds or shades shall not shall match the appropriate requirements for climate and orientation. be modeled. Permanent shading devices such as ins, overhangs, and light shelves shall be modeled. (e) Existing Buildings. For existing building envelopes, the Standard Designs shall relect existing conditions prior to any revisions that are part of the scope of work being evaluated.

Lighting

Lighting power in the Proposed Design shall be determined as follows: (a) Where a complete lighting system exists, the actual lighting power shall be used in the model. (b) Where a lighting system has been designed, the LPD should match the design which shall be determined in accordance with either 7.3.2 or 7.3.3. (c) Where no lighting exists or is speciied, lighting power shall be determined in accordance with the 7.3.2 for the appropriate building type. (d) Lighting system power shall include all lighting system components shown or provided for on plans (including lamps, ballasts, task ixtures, and furniture-mounted ixtures). (e) Exception: For multifamily dwelling units, hotel/motel guest rooms, and other spaces in which lighting systems are connected via receptacles and are not shown or provided for on building plans, assume identical lighting power for the Proposed and Standard Designs in the simulations. (f) Lighting power for parking garages and building facades shall be modeled. (g) Credit may be taken for the use of automatic controls for daylight utilization but only if their operation is either modeled directly in the building simulation or modeled in the building simulation through schedule adjustments determined by a separate daylighting analysis approved by the Authority Having Jurisdiction.

B.8

HVAC Zones Designed

Where HVAC zones are deined on HVAC design drawings, each HVAC zone shall be Same as Proposed Design. modeled as a separate thermal zone.

Exception: Different HVAC zones may be combined to create a single thermal zone, provided that all of the following conditions are met: (a) The space use classiication is the same throughout the thermal zone.

(b) All HVAC zones in the thermal zone that are adjacent to glazed exterior walls face the same orientation or their orientations vary by less than 45 degrees.

(c) All of the zones are served by the same HVAC system or by the same kind of HVAC system.

HVAC Zones Not Designed

Where the HVAC zones and systems have not yet been designed,thermal zones shall be Same as Proposed Design. deined based on similar internal load densities, occupancy, lighting, thermal and space temperature schedules, and in combination with the following guidelines:

Energy Conservation Building Code (ECBC) User Guide

(a)

Separate thermal zones shall be assumed for interior and perimeter spaces. Interior spaces shall be those located greater than 5 m from an exterior wall. Perimeter spaces shall be those located within 5 m of an exterior wall.

(b) Separate thermal zones shall be assumed for spaces adjacent to glazed exterior walls; a separate zone shall be provided for each orientation, except that orientations that differ by less than 45 degrees may be considered to be the same orientation. Each zone shall include all loor area that is 5 m or less from a glazed perimeter wall, except that loor area within 5 m of glazed perimeter walls having more than one orientation shall be divided proportionately between zones.

(c)

Separate thermal zones shall be assumed for spaces having loors that are in contact with the ground or exposed to ambient conditions from zones that do not share these features.

(d) Separate thermal zones shall be assumed for spaces having exterior ceiling or roof assemblies from zones that do not share these features.

HVAC Systems

The HVAC system type and all related performance parameters, such as equipment The HVAC system type and related performance parameters for the Standard Designs shall be determined from Table 10.2. Equipment performance shall meet the requirements capacities and eficiencies, in the Proposed Design shall be determined as follows: of 5. (a) Where a complete HVAC system exists, the model shall relect the actual system type using actual component capacities and eficiencies.

(b) Where an HVAC system has been designed, the HVAC model shall be consistent with design documents. Mechanical equipment eficiencies shall be adjusted from actual design conditions to the standard rating conditions speciied in 5, if required by the simulation model.

(c) Where no heating system exists or no heating system has been speciied, the heating system shall be modeled as electric resistance. The system characteristics shall be identical to the system modeled in the Standard Designs.

Appendix B: Whole Building Performance Method

(d) Where no cooling system exists or no cooling system has been speciied, the cooling system shall be modeled as an air-cooled single-zone system, one unit per thermal zone. The system characteristics shall be identical to the system modeled in the Standard Designs.

B.9

Service Hot Water

The service hot water system type and all related performance parameters, such as The water heating system shall be of the same type of the Proposed Design. For residential equipment capacities and eficiencies, in the Proposed Design shall be determined as facilities, hotels and hospitals the Standard Designs shall have a solar system capable of follows: meeting 20% of the design load. Systems shall meet the eficiency requirements of 6.2.2, the pipe insulation requirements of 6.2.4 and incorporate heat traps in accordance with (a) Where a complete service hot water system exists, the Proposed Design shall relect 6.2.5. the actual system type using actual component capacities and eficiencies.

(b) Where a service hot water system has been speciied, the service hot water model shall be consistent with design documents.

(c) Where no service hot water system exists or has been speciied but the building will have service hot water loads, a service hot water system shall be modeled that matches the system in the Standard Designs and serves the same hot water loads.

(d) For buildings that will have no service hot water loads, no service hot water system shall be modeled.

Appendix B: Whole Building Performance Method

Energy Conservation Building Code (ECBC) User Guide

Miscellaneous Receptacle and process loads, such as those for ofice and other equipment, shall be Receptacle, motor and process loads shall be modeled the same as the Proposed Design. estimated based on the building type or space type category and shall be assumed to be Loads

identical in the proposed and Standard Designss, except as speciically authorized by the Authority Having Jurisdiction. These loads shall be included in simulations of the building and shall be included when calculating the standard building performance and proposed building performance.

Modeling Limitations to the Simulation Program

If the simulation program cannot model a component or system included in the Proposed Design, one of the following methods shall be used with the approval of the Authority Having Jurisdiction: (a) Ignore the component if the energy impact on the trade-offs being considered is not signiicant.

Other systems, such as motors covered by 8 and miscellaneous loads shall be modeled as identical to those in the Proposed Design including schedules of operation and control of the equipment. Where there are speciic eficiency requirements in 8, these systems or components shall be modeled as having the lowest eficiency allowed by those requirements. Where no eficiency requirements exist, power and energy rating or capacity of the equipment shall be identical between the Standard Building and the Proposed (b) Model the component substituting a thermodynamically similar component mod- Design with the following exception: variations of the power requirements, schedules, or control sequences of the equipment modeled in the Standard Building from those el. in the Proposed Design may be allowed by the rating authority based upon documentation (c) Model the HVAC system components or systems using the Standard Designss HVAC that the equipment installed in the Proposed Design represents a signiicant veriiable system in accordance with 5. departure from documented conventional practice. The burden of this documentation Whichever method is selected, the component shall be modeled identically for both the is to demonstrate that accepted conventional practice would result in Standard Building equipment different from that installed in the Proposed Design. Occupancy and occupancy Proposed Design and Standard Designs models. schedules may not be changed.

B.10

Appendix B: Whole Building Performance Method

10.3.1.1 Calculating Proposed and Standard Design

a) Design Model
The Proposed Design and the corresponding Standard Design shall be consistent with information contained on the plans and speciications. Some buildings, such as retail malls and speculative ofice buildings typically are built in phases. For example, the core mechanical system may be installed with the base building, while the ductwork and terminal units are installed later as part of tenant improvements. For the purpose of calculating the Proposed Building, the rule is simple: the features that are not yet designed or documented in the construction documents are assumed to minimally comply with the applicable prescriptive requirements of the ECBC, as speciied in Sections 4 through 8. In cases where the space use classiication is not known, the default assumption is to classify it as ofice space using the Building Area Method. The WBP method is based on the assumption that non-residential buildings are both heated and cooled. Even if not installed initially, it is common for buildings lacking a heating or cooling system to have one retroitted by future occupants. Accordingly, there is a special rule for calculating energy use in the Proposed Design when a buildings HVAC system is heating-only or cooling-only: the building must be modeled as if it is going to have both heating and cooling. The missing system is modeled as the default heating or cooling system that just meets the prescriptive requirements of the ECBC. The same system is modeled for both Standard and Proposed Designs. (Refer ECBC 4.0).

b) Space Use Classiications

A key task in modeling the Proposed Design is assigning space use classiications to different areas of the building. These classiications are used to assign lighting power density assumptions and to differentiate areas within the building that may have different operating schedules and characteristics (thermostat settings, ventilation rates, etc.). The choice of space use classiications is taken from one of the two lighting tables in the ECBC: either Table 7.1 (Interior Lighting Power-Building area method) or Table 7.2 (Interior Lighting Power- Space Function method). The designer may choose either classiication scheme but may not mix the schemes by using one for part of the building and the other for the rest of the building. Building, in this context, refers to the space encompassed by a single building permit application, which may be less than the complete building. The secondary support areas associated with each of the major building types would be included in each building type. For example, if a building included both ofice and retail areas, the corridors and restrooms associated with the ofice occupancy would be included in the ofice area and the storage or/and dressing room areas associated with the sales loor would be included in the retail area.

c) Schedules
Schedules are used to describe the percentage of a maximum design value of an internal load that is applicable during a particular time period, usually one hour, i.e., lighting power density, miscellaneous equipment (plug load) power density, occupant load or any other signiicant load thermostat set point (s) applicable in this time period, or the availability (on/off), and control operation of a system or system component, e.g., cooling systems, fans, chillers, or pumps.

Energy Conservation Building Code (ECBC) User Guide

B.11

Appendix B: Whole Building Performance Method

Equipment Lighting Occupancy

Schedules have a large impact on the overall energy consumption. Designers are required to specify Weekday, Saturday, Sunday, and Holiday operation in each schedule. An example for Weekday schedules in an ofice building is shown below. The ECBC allows designers to select reasonable or typical schedules for the building. In all cases, the schedules for the Proposed Design and the Standard Design shall be identical. This means that the Proposed Design may not take advantage of scheduling changes. It further means that any equipment in the Proposed Design that saves energy by altering operating patterns or proiles must be modeled explicitly; it is not suficient simply to assume a schedule change and use that to account for the electricity savings. An example is daylighting controls, which reduce lighting power when daylight is available in a space. The Proposed Design must simulate the actual performance of the daylighting control in response to daylight availability, rather than the simulator simply assuming some schedule change that arbitrarily reduces lighting power during daylight hours. Another example of equipment that must not be modeled by reducing operating hours in the Proposed Design are occupancy-sensing controls that turn off equipment when not needed. While this type of equipment might well be installed because of the owners conviction that it is a good investment, there is no credit for it under the WBP method. In selecting the schedules, it is prudent to consider the likely long-term operation of the building. For example, if a new school will initially operate on a traditional schedule, but the school district has a policy of shifting its schools over to year-round operation, then it would be prudent to apply a year-round schedule in the WBP method modeling. The selected schedules should likewise not intentionally misrepresent the operation of the building. If a grocery store chain keeps its stores open 24 hours a day, it would be inappropriate to use a 12-hour-a-day operating schedule in the modeling.

d) Building Envelope
The building footprint and overall geometry must be identical for both the Standard and Proposed Designs, and must use the design shown on the inal architectural drawings, including building shape, dimensions, surface orientations, opaque construction assemblies, glazing assemblies, etc. That is, they must have the identical plan, conditioned loor area, number of loors, loor-to-loor distances, wall and roof areas, surface tilts and orientation. In some cases, the building envelope may already exist, as in the case of newly conditioned space or a tenant build-out of a shell building; in these cases, the existing building envelope is modeled. The Standard Design will have the maximum allowable window-to-wall-ratio (WWR) in each orientation, but
Energy Conservation Building Code (ECBC) User Guide B.12

Appendix B: Whole Building Performance Method

the Proposed Design may exceed this limit, provided compliance is achieved. Opaque assemblies like walls, roofs and loors must be described by material layer as per the architectural drawings. For the Standard Design, the characteristics (U-factor) of these envelope components are set to the prescriptive values speciied in ECBC 4.0. The heat capacities for each assembly type must match the heat capacities of the Proposed Design. This is because heat capacities may have a signiicant effect on the performance of envelope components, which shows up in the simulation runs but they are not a requirement of the ECBC. Heat capacity is modeled to be the same in both the Proposed Design and the Standard Design simulation runs, and so is energy neutral under the WBP method. For the Standard Design, exterior roof surfaces, other than those with ventilated attics, must be modeled assuming a surface relectance value of 0.30 (Refer ECBC Table 10.1). If a Proposed Design calls for a relective roof surface, however, the model may assume a long-term average relectance of 0.45, which results in the lower heat absorption of the relective surface and makes a conservative allowance for degradation of the relectivity over its lifetime. For this exception to be allowed the speciied relectance of the roof in the Proposed Design must exceed 0.70 and its emittance must exceed 0.75. (As per ASHRAE 90.1, 2004) i) Windows /Fenestration The solar, thermal, and optical performance of windows systems are deined by the combination of four main parameters, i.e., the area as deined by the window-to-wall ratio, thermal transmittance (U-factor), Solar Heat Gain Coeficient (SHGC), and Visible Light Transmission (VLT). Fenestration Area Fenestration areas and performance are strong drivers of energy use in buildings. Therefore, the ECBC places great emphasis in how these values are calculated and applied for compliance. ECBC 4.3.3 sets the prescriptive upper limits on vertical fenestration area and skylight area. If the fenestration areas for the Proposed Design are less than these limits, the Standard Design shall have the same areas and orientations as the Proposed Design. If the fenestration areas in the Proposed Design exceed these limits, then the corresponding areas in the Standard Design must be adjusted down to these limits AND corresponding increases made to opaque areas so that the gross wall area and gross roof area are the same for both the Proposed Design and the Standard Design. ECBCs prescriptive envelope requirements do not provide an exception for street-level, street-side vertical fenestration (e.g., store display windows). Thus, such fenestration must be modeled identically for the Proposed Design and the Standard Design simulation runs so that the representation of these types of fenestration is energy neutral. U-Factors The U-factor for the Standard Design is set to the minimum required for the climate, as speciied in ECBC Table 4.3. The minimum U-factor is a function of the percentage of glazing (WWR) in a wall or roof, as described above. Solar Heat Gain Coeficient The solar heat gain coeficient value for the fenestration applied in the Standard Design is set to the maximum required for the climate and for each orientation, as speciied in ECBC Table 4.3. The maximum SHGC is a function of the glazing percentage of wall or roof, which is based on the Proposed Design as described above. If the vertical fenestration to be used is unrated, then the SHGC values in ECBC Table 11.1 must be used. ii) Shading of Fenestration Glazing installed in the Standard Design must be modeled as being lush with its wall or roof surface, and without any external shading devices. This ruling allows the Proposed Design to use to its advantage shading from window recesses, overhangs, side ins, or other permanent shading devices that reduce solar gains on the glazing.

Energy Conservation Building Code (ECBC) User Guide

B.13

Appendix B: Whole Building Performance Method

Interior shading devices, if not automatic, should not be modeled in the Proposed Design. In Standard Design, no shading should be modeled. Exceptions for Envelope Any simulation program necessarily relies on a somewhat simpliied description of the building envelope. It is usually time-consuming and dificult to explicitly detail every minor variation in the envelope design, and if good engineering judgment is applied, these simpliications wont result in a signiicant decline in accuracy. Three exceptions, where more substantial simpliications may be made, are:
Minor Assemblies: Frequently, there will be small areas on the building envelope with unique thermal characteristics. The ECBC exempts any envelope assembly that covers less than 5% of the total area of a given assembly type (e.g., exterior walls or roofs) from being treated as a separate envelope component. Instead, that area may be added to an adjacent assembly of the same type. For example, if there is an exterior wall constructed of load-bearing masonry, but there are small wood-framed inill areas, the inill areas may be treated as if the entire wall is of masonry. Note that the gross wall area is unchanged, and no areas are left out of the model. Different Tilt or Azimuth: This exception, primarily intended to address curved surfaces, speciies the minimum

number of orientations into which these surfaces must be split up. The Standard allows similarly oriented surfaces to be grouped under a single tilt or azimuth, provided they are of similar construction and provided the tilt or azimuth of the surfaces are within 45 degree of each other. They may be grouped as a single surface or a multiplier may be used.
Fenestration: Interior and/or exterior shading devices in the Proposed Design shall not be modeled unless they are automatically controlled. In the Standard Design, shades of any kind are not modeled. When the window area in the Proposed Design exceeds the prescriptive maximum, the window area in the Standard Design is set to the prescriptive maximum area and representative opaque wall area replaces any excess window area. Thus the overall wall area (opaque wall + window area) is the same for both standard and proposed buildings. The window area in Standard Design is decreased uniformly in each orientation so that the fraction of total window area in each direction is the same in both Standard Design and Proposed Design simulation models.

e) Lighting Systems
Under the WBP method, lighting systems are a very important part of overall building performance for most non-residential building types. Any lighting system eficiency improvements or reductions are relected as energy savings in the WBP method. The description of lighting systems in building energy simulation models must incorporate the following two characteristics: Application of a lighting power density (LPD) for each space or thermal zone of the building model. This may be determined using one of the two methods deined in 7.3.2 (building area method) or 7.3.3 (space function method). An operational schedule for the lighting system which describes the percentage of the maximum LPD value that is energized during a particular hour There are further requirements if the electric lighting system is to be controlled in response to the amount of daylight in perimeter zones of the building. In such cases, the building simulation program must be able to explicitly model daylight levels in each perimeter space that has daylight linking. Light sensors must be modeled in these zones, and a control strategy must be applied that modulates electrical energy output from the electric lighting system. Typically there are at least three daylight linked control schemes to modulate electrical energy output: Stepped control: in this control scheme, the electrical lighting system can respond to the presence of daylight in deined steps Linear control: the lighting system modulates its output in a linear function to a prescribed minimum level, and

Energy Conservation Building Code (ECBC) User Guide

B.14

Appendix B: Whole Building Performance Method

Linear/off: the lighting system modulates its output in a linear function and will switch off (use zero electrical energy) when there is suficient daylight in the space Either the building area or space function method may be used, but the categorization of spaces must be identical between the Standard Design and the Proposed Design. The LPD for the Proposed Design is taken from the design documents for the building. If a lighting system already exists, then the lighting system design for Proposed Design will be based on the actual lighting power density of the existing system. In the special case where no lighting system or design exists, as in a shell building where the lighting will be installed by a future tenant, then a default lighting power density must be assumed, based on the building area method for the appropriate building type. If no building type is known, then an ofice building is assumed, (refer ECBC Table 10.1) Exterior lighting systems as deined in ECBC 7.2.3 refers to grounds luminaires which operate at greater than 100W. They shall contain lamps having a minimum eficacy of 60 lm/W unless, the luminaire is controlled by a motion sensor or exempt under 7.1, as mentioned below: Emergency lighting that is automatically off during normal building operation and is powered by battery, generator, or other alternate power source Lighting in dwelling units

f) HVAC
Incorporating HVAC systems into whole building energy simulation models is a complex process. It requires knowledge of how buildings respond to climate, in addition to knowledge of the coniguration of HVAC systems and appropriate control strategies. For the purpose of building energy simulation it is useful to think of the building model as having three HVAC type components, ZONES, SYSTEMS and PLANT. i) HVAC Zoning A key task in developing both of the simulation models is to divide the Proposed Design into a series of spaces or thermal zones to be input to the energy simulation program. Due care and consideration needs to be taken to divide the building into an appropriate number of thermal zones. There are several considerations for this division, and some of these considerations can be conlicting. The following are some of the considerations that need to be thought through when dividing the building for simulation analysis. Building areas that are thermodynamically similar spaces and whose heating and cooling loads can be satisied through use of a single thermostat (or other type of temperature control) can be combined in a single thermal zone. Since this requires mapping of the HVAC system design into the simulation model, the simulator needs to work interactively with the services consultant. Building areas that perform a similar function in the building design may be combined to form a thermal zone for example, some open plan ofice areas, or retail shop areas that have similar loads and operate similar hours may be combined. These areas would have identical schedules applied for operation of internal loads and HVAC systems. Building areas that have the same lighting power density may be combined, i.e. the use of space use classiications. The choice of space use classiications is taken from one of the two lighting tables in the ECBC, either Table 7.1 (Interior Lighting Power-Building area method) or Table 7.2 (Interior Lighting Power-Space Function method). The designer may choose either classiication scheme but may not mix the schemes by using one for part of the building and the other for the rest of the building. Building in this context refers to the space encompassed by a single building permit application, which may be less than the complete building. The secondary support areas associated with each of the major building types would be included in each building type. For example, if a building included both ofice and retail areas, the corridors and restrooms associated with the ofice occupancy would be included in the ofice area and the storage or/and dressing room areas associated with the sales loor would be included in the retail area. HVAC Zones are identical to the thermal zones or spaces discussed earlier. An HVAC designer will consider the

Energy Conservation Building Code (ECBC) User Guide

B.15

Appendix B: Whole Building Performance Method

internal and external loads on each zone to calculate a design day cooling and heating load, and the maximum outside air ventilation required. He or she may combine two or more thermal zones into a thermal block designed to be conditioned by a single HVAC SYSTEM, for example, an Air Handling Unit (AHU) or an DX system. If the building uses central air-conditioning systems (as opposed to DX systems, see Chapter 5), then a series of HVAC SYSTEMS may be served by one or more HVAC PLANT component (chillers, pumps, cooling towers etc). For the WBP method using building energy simulation analysis, HVAC ZONES must be described to be identical in both the Standard Design and the Proposed Design Models. This rule ensures consistency with the requirement that the shape and area of the building envelope for the Standard Design be the same as for the Proposed Design, and that the space use classiications be the same. HVAC Zoning Based On HVAC Design As noted earlier, building areas that are thermodynamically similar spaces and whose heating and cooling loads can be satisied through use of a single thermostat (or other type of temperature control) can be combined in a single thermal zone. The outside air low quantities, and control strategies applicable to the duct outlets or other terminal units controlled by this single thermostats may be part of the HVAC ZONE description. Clearly, this process requires mapping of the HVAC SYSTEM design into the simulation model, and the simulator needs to work interactively with the services consultant. Use of HVAC Zone Multiplier In some simulation programs, the interior HVAC ZONES of a multi-story building, which may be physically separate zones on each loor can be reasonably combined and treated as a single thermal zone with a multiplier. Use of a multiplier allows simpliication of the calculation of electricity consumption for the whole building without having to repeatedly describe many similar or identical zones in the simulation model, thus saving time and effort without signiicant loss of accuracy. However, a cafeteria or computer room in an ofice building would need to be modeled separately, as would lower-loor retail uses. The following conditions must be met to be able to use the multiplier option: All of the space use classiications must be the same throughout the thermal zone. This ensures that they have the same load and schedule characteristics. For exterior (or perimeter) HVAC ZONES with glazing, the glazing for all zones included in the thermal block must have the same orientation or at least their orientations must be within 45 degrees of each other. This ensures that they have the same solar heat gain characteristics. This is not to say that the zones may not have two or more glazing orientations a corner ofice could easily have two but that the zones must have similar orientations. It would be acceptable, for example, to group all of the northeast corner ofices on the intermediate loors of an ofice tower into a single thermal block. All of the HVAC ZONES in different loors must be served either by the same HVAC SYSTEM or by the same kind of HVAC SYSTEM. This is so that the simulation program can accurately model the performance of the system (s) serving the zones. HVAC Zoning When No HVAC Design Exists In a situation where an HVAC ZONING plan has not been designed, then a coniguration of thermal blocks must be assumed for the WBP method. This situation is quite common in commercial buildings where the future tenants will determine the zoning of spaces in the building. In this case, the building must be divided into thermal zones based on similar internal load densities and lighting power densities, operational schedules, occupancy patterns, space temperature schedules, etc. There are several guidelines that should be followed in this situation, as described below. Zoning Based on Perimeter and Interior Spaces In situations when no HVAC design has been developed, divide the loor plate into perimeter spaces than are within 5 meters of an exterior wall, and interior spaces that are more than 5 meters from an exterior wall.

Energy Conservation Building Code (ECBC) User Guide

B.16

Appendix B: Whole Building Performance Method

Zoning Based on Glazing Orientation Glazed exterior walls should be assigned to different perimeter thermal zones for each major orientation. Orientations within 45 degrees of each other may be combined. Spaces with two or more glazed orientations, such as corner ofices, should be divided proportionately between zones having the different orientations. Zoning Based on Floor Levels Spaces exposed to ambient conditions, such as the top loor or an overhanging loor, and spaces in contact with the ground, such as the ground loor, must be zoned separately from zones that are not exposed to ambient conditions, such as intermediate loors in a multi-story building. Therefore, a multi-storey tower ofice building could be divided into a top loor, a typical middle loor with the appropriate loor multiplier, and a bottom loor. Thermal Zones For Multi-Family Residential Buildings Multifamily residential buildings are another special case. In general, the residential spaces must be treated as separate thermal zones, except that some combinations are allowed. Units all facing the same orientation, and having similar conditions at the top, bottom, and sides, may be combined. Similar corner units may be combined, and units with similar roof or loor loads may be combined. ii) HVAC Systems Deining HVAC systems for use with whole building simulation programs is complex, and there are many interrelated rules. Some of the rules that govern the description of HVAC SYSTEMS for the ECBC whole building performance method are: The HVAC SYSTEM described in the Standard Design Model should just meet the prescriptive requirements of the ECBC. These requirements are deemed representative of current standard practice that meets the ECBC. Where possible, the HVAC SYSTEM is to be conceptualized as completely as possible on the actual system designed for the Proposed Design. This includes the system type, equipment capacities and eficiencies, controls, ancillary features (such as economizers), etc. The equipment eficiencies may need to be adjusted to meet the needs of the simulation program. While eficiencies may be most accurately speciied at the buildings design conditions, most simulation programs require eficiencies to be speciied at standard rating conditions, such as those given in ECBC 5.0. Where the entire HVAC SYSTEM design is not known, as in the case of a shell-and-core design, the unknown parts of the system are assumed to just meet the prescriptive requirements of the ECBC and to be energy neutral. This strategy prevents gamesmanship with the undeined system components. Gamesmanship is the practice of artiicially reducing the eficiency of the Standard Design in order to increase the apparent relative eficiency of the Proposed Design4. Where the complete HVAC SYSTEM exists, the Proposed Design and Standard Design are based on the existing HVAC system for example, it out of an existing speculative building for a tenant. The subject of the building permit is primarily the interior construction and lighting system and does not include the HVAC system because it has already been built and permitted. Both simulation models would also include the existing building envelope. Where no HEATING SYSTEM exists, a default heating system must be assumed and modeled. It should be a simple heating system that burns fossil fuel, sized with suficient capacity to meet the design heating loads for the Proposed Design. An identical system (with sizing adjustments) must be assumed for the Standard Design.
4 The WBP method is more vulnerable to this sort of abuse, which is why the rules for constructing the Standard Design must be so speciic. The WBP modeling rules for part-load eiciency and system sizing are intended to minimize these efects on the trade-of calculations for the other measures in the building. For example, electricity consumption diferences cannot be gained for a diference between a properly sized HVAC system in the Proposed Design and an improperly sized HVAC system for the Standard Design. The modeling rules are discussed individually in the following sections:

Energy Conservation Building Code (ECBC) User Guide

B.17

Appendix B: Whole Building Performance Method

Where no COOLING SYSTEM exists, a default cooling system must be assumed and modeled for both the Standard Design and Proposed Design. Minimum Eficiencies The minimum eficiencies for HVAC equipment (5.2.2) and for service hot water heating equipment (6.2.2) must be used for the applicable equipment in the Standard Design. This includes any part-load eficiencies, if these are speciied. These eficiency requirements set the baseline for equipment trade-offs under the WBP method. The actual equipment eficiency of the Proposed Design is then used to calculate the Standard Design. Since mechanical and service hot-water heating equipment eficiency is a prescriptive requirement, if the equipment is covered by these equipment requirements, the equipment eficiency in the Proposed Design must be equal to or greater than the prescriptive equipment eficiency. If mechanical or service hot water heating equipment falls outside of those listed in the eficiency tables, the standard equipment eficiency shall be equal to the eficiency of the equipment in the Proposed Design. Thus the only trade-off available for equipment eficiency is to specify higher eficiencies than those called for in the ECBC, which would give electricity consumption savings for the design. Equipment Capacities The equipment capacities for the Standard Design shall be based on sizing runs for each orientation (per Table 10.1) and shall be oversized by 15% for cooling and 25% for heating; i.e., the ratio between the capacities used in the annual simulations and the capacities determined by the sizing runs shall be 1.15 for cooling and 1.25 for heating. Unmet load hours for the Proposed Design or Standard Designs shall not exceed 300 (of the 8,760 hours simulated), and unmet load hours for the Proposed Design shall not exceed the number of unmet load hours for the Standard Design by more than 50. If unmet load hours in the Proposed Design exceed the unmet load hours in the Standard Design by more than 50, simulated capacities in the Standard Design shall be decreased incrementally and the building re-simulated until the unmet load hours are within 50 of the unmet load hours of the Proposed Design. If unmet load hours for the Proposed Design or Standard Design exceed 300, then simulated capacities shall be increased incrementally, and the building with unmet loads re-simulated until unmet load hours are reduced to 300 or less. Sizing Runs Weather conditions used in sizing runs to determine Standard equipment capacities may be based either on hourly historical weather iles containing typical peak conditions or on design days developed using 99.6% heating design temperatures and 1% dry-bulb and 1% wet-bulb cooling design temperatures. Preheat Coils If the HVAC system in the Proposed Design has a preheat coil and a preheat coil can be modeled in the Standard system, the Standard system shall be modeled with a preheat coil controlled in the same manner as the Proposed Design. Fan System Operation Supply and return fans shall operate continuously whenever spaces are occupied and shall be cycled to meet heating and cooling loads during unoccupied hours. If the supply fan is modeled as cycling and fan energy is included in the energy-eficiency rating of the equipment, fan energy shall not be modeled explicitly. Ventilation Minimum outdoor air ventilation rates shall be the same for the Proposed and Standard Designs.
Exception: When modeling demand-control ventilation in the Proposed Design when its use is not required by

Ventilation Controls for High-Occupancy Areas. Systems with design outdoor air capacities greater than 1400 L/s serving areas having an average design occupancy density exceeding 100 people per 100 m2 shall include means to automatically reduce outdoor air intake below design rates when spaces are partially occupied. Design Air Flow Rates System design supply air low rates for the Standard Design shall be based on a supply-air-to-room-air temperature difference of 11C. If return or relief fans are speciied in the Proposed Design, the Standard Design shall also be

Energy Conservation Building Code (ECBC) User Guide

B.18

Appendix B: Whole Building Performance Method

modeled with fans serving the same functions and sized for the Standard system supply fan air quantity less the minimum outdoor air, or 90% of the supply fan air quantity, whichever is larger. Supply Fan Power System fan electrical power for supply, return, exhaust, and relief (excluding power to fan powered VAV boxes) shall be calculated using the following formulas:
Pfan: 746 /(1 - e[ -0.2437839 ln( bhp ) - 1.685541 ]) bhp Where Pfan: electric power to fan motor (watts) bhp: brake horsepower of Standard fan motor from the table below, where cfm represents design supply low rate.

Table 10.2: Standard Fan Brake Horsepower Supply Air Volume

< 9400 L/s 9400 L/s

Baseline Fan Motor Brake Horsepower

Constant Volume Systems 1 4
17.25 + (cfm - 20000) 0.0008625 17.25 + (cfm - 20000) 0.000825

Variable Volume Systems 5 8

24 + (cfm - 20000) 0.0012 24 + (cfm - 20000) 0.001125

Exception: If systems in the Proposed Design require air iltering systems with pressure drops in excess of 1 in. w.c. when ilters are clean, the allowable fan system power in the Standard Design system serving the same space may be increased using the following pressure credit: Pressure Credit (watts): CFMilter * (Spilter 1)/4.984 where CFMilter: supply air volume of the proposed system with air iltration system in excess of 250 Pa Spilter: air pressure drop of the iltering system in w.g. when the ilters are clean.

Exhaust Air Energy Recovery Individual fan systems that have both a design supply air capacity of 2400 L/s or greater and have a minimum outdoor air supply of 70% or greater of the design supply air quantity shall have an energy recovery system with at least 50% recovery effectiveness. 50% energy recovery effectiveness shall mean a change in the enthalpy of the outdoor air supply equal to 50% of the difference between the outdoor air and return air at design conditions. Provision shall be made to bypass or control the heat-recovery system to permit air economizer operation, where applicable. Piping Losses Piping losses shall not be modeled in either the proposed or Standard Designs for hot water, chilled water, or steam piping. Type and Number of Chillers Electric chillers shall be used in the Standard Design regardless of the cooling energy source, e.g., direct ired absorption, absorption from purchased steam, or purchased chilled water. The Standard Designs chiller plant shall be modeled with chillers having the number and type as indicated in table below as a function of building conditioned loor area. Table 10.3: Type and Number of Chillers Building Peak Cooling Load
300 tons > 300 tons and < 600 tons 600 tons

Number and Type of Chiller (s)

1 water-cooled centrifugal chiller 2 water-cooled centrifugal chillers sized equally Minimum 2 water-cooler chillers with one or more chillers equal to 600 tons and one chiller less than 600 tons

Energy Conservation Building Code (ECBC) User Guide

B.19

Appendix B: Whole Building Performance Method

Chilled Water Design Supply Temperature (System Type: RHFS /ECBC Table 10.2) Chilled water design supply temperature shall be modeled at 6.7C and return water temperature at 13C. Chilled Water Supply Temperature Reset (System Type: RHFS /ECBC Table 10.2) Chilled water supply temperature shall be reset based on outdoor dry-bulb temperature using the following schedule: 7C at 27C and above, 12C at 16C and below, and ramped linearly between 7C and 12C at temperatures between 16C and 27C. Chilled Water Pumps (System Type: RHFS from ECBC Table 10.2) The Standard Design pump power shall be 349 kW/1000 L/s. Chilled water systems serving 11,148 m2 or more shall be modeled as primary/secondary systems with variable-speed drives on the secondary pumping loop. Chilled water pumps in systems serving less than 11,148 m2 shall be modeled as a primary/secondary system with secondary pump riding the pump curve. Heat Rejection (System Type: RHFS /ECBC Table 10.2) The heat rejection device shall be an axial fan cooling tower with two speed fans. Condenser water design supply temperature shall be 29C or 5.6C approach to design wet-bulb temperature, whichever is lower, with a design temperature rise of 5.6C. The tower shall be controlled to maintain a 21C leaving water temperature where weather permits, loating up to leaving water temperature at design conditions. The Standard Design condenser water pump power shall be 310 kW/1000 L/s. Each chiller shall be modeled with separate condenser water and chilled water pumps interlocked to operate with the associated chiller. Supply Air Temperature Reset (System Type: RHFS /ECBC Table 10.2) Supply air temperature shall be reset based on zone demand from the design temperature difference to a 5.6C temperature difference under minimum load conditions. Design air low rates shall be sized for the reset supply air temperature, i.e., a 5.6C temperature difference. VAV Minimum Flow Set points (System Type: ECBC Table 10.2) Minimum volume set points for VAV reheat boxes shall be 2.15 L/sm2 of loor area served. Fan Power (System Type: RHFS /ECBC Table 10.2) Fans in parallel VAV fan-powered boxes shall be sized for 50% of the peak design low rate and shall be modeled with 0.74 W per L/s fan power. Minimum volume set points for fan-powered boxes shall be equal to 30% of peak design low rate or the rate required to meet the minimum outdoor air ventilation requirement, whichever is larger. The supply air temperature setpoint shall be constant at the design condition. VAV Fan Part-Load Performance (System Type: RHFS /ECBC Table 10.2) VAV system supply fans shall have variable speed drives, and their part-load performance characteristics shall be modeled using either Method 1 or Method 2 mentioned in table below. Table 10.4: Part-Load Performance for VAV Fan Systems Method 1 Part-Load Fan Power Data
Fan Part-Load Ratio
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70

Fraction of Full-Load Power

0.00 0.03 0.07 0.13 0.21 0.30 0.41 0.54

Energy Conservation Building Code (ECBC) User Guide

B.20

Appendix B: Whole Building Performance Method

0.80 0.90 1.00

0.68 0.83 1.00

Method 2 Part-Load Fan Power Equation

Pfan: 0.0013 + 0.1470 PLRfan + 0.9506 (PLRfan)2 -0.0998 (PLRfan)3 where Pfan: fraction of full-load fan power and PLRfan: fan part-load ratio (current cfm/design cfm).

Hot Water Supply Temperature (System Type: ECBC Table 10.2) Hot water design supply temperature shall be modeled as 82C and design return temperature as 54C. Hot Water Supply Temperature Reset (System Type: ECBC Table 10.2) Hot water supply temperature shall be reset based on outdoor dry-bulb temperature using the following schedule: 82C at 7C and below, 66C at 10C and above, and ramped linearly between 82C and 66C at temperatures between 7C and 10C. Hot Water Pumps (System Type: ECBC Table 10.2) The Standard Design hot water pump power shall be 301 kW/1000 L/s. The pumping system shall be modeled as primary- only with continuous variable low. Hot water systems serving 11,148 m2 or more shall be modeled with variable speed drives, and systems serving less than 11,148 m2 shall be modeled as riding the pump curve.

g) Service Hot-Water Systems

Proposed Design The WBP method provides an opportunity to include the service hot-water systems in the overall building performance, and so for it to be part of the trade-off procedures. These systems are treated similarly to the HVAC systems discussed above. The basic rule is that the Proposed Design hot water system is modeled in accordance with the design documents, including equipment types, capacities, eficiencies, insulation, controls, and all other related performance parameters. In cases where a service hot-water system already exists, the model must be based on that systems characteristics. If neither case applies, i.e. there is no service hot-water system, then, none is modeled. The last rule is different than for other energy-related systems in the building because service water heating generally has little interaction with the other energy systems. (Refer ECBC Table 10.1 (7)) Standard Designing Service water-heating systems may participate in the WBP method trade-offs when they are eligible (under the same permit application as the rest of the Proposed Design). They must be modeled as the same water heater type and must be assumed to have the same performance characteristics, such as hot water demand, fuel type, operating schedules, circulating pumps, etc. The only characteristic, then, that may contribute to electricity consumption savings is the water heater equipment eficiency. There is a special case where the service water heater is also used for space heating (or vice versa). For WBP method purposes, the Standard Design is assumed to model solar system capable of meeting 20% of the design load for residential facilities, hotels and hospitals. The equipment should be modeled so that system shall meet the eficiency requirements of ECBC 6.2.2, the pipe insulation requirements of ECBC 6.2.4 and incorporate heat traps in accordance with ECBC 6.2.5.

h) Miscellaneous Loads:
Proposed Design If there are signiicant energy-related systems, besides those discussed in above sections, that generate internal heat gains or otherwise interact with the other energy systems, then they should be modeled as part of the

Energy Conservation Building Code (ECBC) User Guide

B.21

Appendix B: Whole Building Performance Method

proposed and Standard Designs. For example, most nonresidential buildings have substantial plug loads and some have process loads. These should be modeled using the best available information about their energy characteristics from the design drawings or, when applicable, from the existing systems already in place. Systems that do not interact substantially with other energy systems, such as elevators or parking garage fans, may be neglected in the Proposed Building modeling. (Refer ECBC Table 10.1) Standard Design The WBP method does not Electricity consumption savings for non-HVAC motors or for other miscellaneous energy-related equipment in a building, such as elevators, conveyors, autoclaves, etc. Where these systems contribute signiicant loads to the building, they should be modeled, but they must be identical in the proposed and standard runs. (Refer ECBC Table 10.1) Table 10.5: HVAC Systems Map (Reproduced from ECBC 10.2) Residential More than 3 stories Less than 3 loors or less than 7,500 m
PSZb
Packaged rooftop air conditioner Constant volume Direct expansion Electric resistance

Nonresidential 4 or 5 loors or less More than 5 loors than 7,500 m or 5 or more than loors or less and 15,000 m 7,50015,000 m
RHFS
Central cooling plant with constant volume AHU for each zone Constant volume air handler for each zone Chilled waterc Electric resistance

Code System type

PTACa
Packaged terminal air conditioner Constant volume Direct expansion Electric resistance

RHFS
Central cooling plant with variable air volume AHU for each zone Variable air volume air handler Chilled waterc Electric resistance

Fan control Cooling type Heating type

a PTAC equipment eficiency shall be per Table 10.6. A PTAC unit is a factory selected wall sleeve and separate un-encased combina-

tion of heating and cooling components, assemblies, or sections. It may include heating capability by hot water, steam, or electricity and is intended for mounting through the wall to serve a single room or zone.
b PSZ equipment eficiency shall be per Bureau of Indian Standard 8148 (1988) c If the proposed building has an air cooled chiller/system then the budget building shall have Air-cooled chiller otherwise the budget

case shall have water cooled centrifugal chillers. If the building has a mix of air and water cooled chillers then, the Standard Design shall have the mix of air and water cooled chillers in the same proportion. Chiller Eficiencies shall be as per Table 5.1 of the Code.

Table 10.6: Electrically Operated Packaged Terminal Air Conditioners Single-Package Vertical Air Conditioners Minimum Eficiency Requirements
Equipment Type
PTAC (Cooling Mode) New Construction PTAC (Cooling Mode) Replacementsa

Size Category (Input)

All capacities All capacities

Subcategory or Rating Condition

35C db outdoor air 35C db outdoor air

Minimum Eficiency
3.66 (0.213 Cap/1000)b COP 3.19 (0.213 Cap/1000)b COP

a Replacement units must be factory labeled as follows: Manufactured for Replacement Applications Only; not to be Installed in New Construction

Projects. Replacement eficiencies apply only to units with existing sleeves less than 16 in. high and less than 42 in. wide.
b Cap means the rated cooling capacity of the product in Btu/h. If the units capacity is less than 7000 Btu/h, use 7000 Btu/h in the calculation. If the units capacity is greater than 15,000 Btu/h, use 15,000 Btu/h in the calculation.

Source: ASHRAE 90.1, 2004

Percentage Improvement The formula below demonstrates a percentage performance improvement in the proposed and Standard Design

Energy Conservation Building Code (ECBC) User Guide

B.22

Appendix B: Whole Building Performance Method

per ECBC by a whole building performance using building performance rating method used in chapter 10 of ECBC. The minimum energy saving percentage applicable to LEED-India and GRIHA rating systems is, as under. % Improvement = 100 (Energy Use in Standard Design - Energy Use in Proposed Design)/Energy Use in Proposed Design

Energy Conservation Building Code (ECBC) User Guide

B.23

Appendix B: Whole Building Performance Method

Case Study
To demonstrate ECBC compliance for building design using WBP method, building energy simulation models need to be developed. This document uses two important terms to understand the process Standard Design and the Proposed Design. To evaluate energy performance of the Proposed Design and to see if it is compliant with ECBC, one needs to build a hypothetical simulation model based on the methodology described in Appendix B of the Guide (also explained in this Guide). This hypothetical model is called Standard Design. Sometimes Standard Design is also referred to as Base Case. Energy consumption in the Standard Design is compared with the energy consumption in the Proposed Design. If the energy consumption in the Proposed Design is more than that of the Standard Design, one needs to incorporate energy conservation measures (ECMs) to improve the energy performance of the Proposed Design for achieving ECBC compliance. Hence in this case study after analyzing the design inputs and incorporating the ECMs, the Proposed Design model has been created. The process of creating the Standard Design model and the Proposed Design model, their inputs for simulations and their results are discussed and explained in this case study. The hypothetical building used in the case study is located in Ahmedabad, Gujarat, India. The steps involved for ECBC compliance using WBP method are: 1. 2. 3. 4. 5. 6. 7. 8. 9. Ensure that the building design conforms to the local building bye laws and regulations Comply with the mandatory requirements of the ECBC Create the Proposed Design model Create the Standard Design model Compare the energy consumption of the Proposed Design with that of the Standard Design If the energy consumption of the Proposed Design is more than that of Standard Design, incorporate additional ECMs in the Proposed Design Ensure that the Standard Design created in Step 4 is still valid. If necessary, revise the Standard Design Repeat step 5 through 7 till energy consumption in the Proposed Design is less than or equal to the energy consumption in Standard Design Prepare the compliance documents

All the above steps are dealt with in detail in this chapter. Before commencing with the data input process for the model, the project should refer to Appendix E Climate Zone Map of India in the Code to check the climate zone in which the site is located. The Guide also lists various cities and their corresponding climate zones. Weather iles for 58 cities from India are available at: http://www.eere.energy.gov/buildings/energyplus/cfm/weather_data3.cfm/region=2_asia_wmo_region_2/ country=IND/cname=India. This weather data is ready to be used in EnergyPlus simulation software but can be customized for other simulation tools using appropriate weather ile converter program. The building proposed for the case study is in Ahmedabad, which is classiied under hot and dry climate. The building should then be classiied either as a 24-hour activity building or a daytime activity building because the ECBC speciications for the U-factors of the building envelope are mandated according to the climate zone and the occupancy type of the building. However, before going into the details of ECBC compliance, it is necessary to describe the case study used for demonstration. Building Description a. The building proposed for the case study is in Ahmedabad, which is classiied under hot and dry climate

Energy Conservation Building Code (ECBC) User Guide

B.24

Appendix B: Whole Building Performance Method

as per Appendix E of the Code. b. The building in this case study is a daytime use building. c. The building used in this case study is a square building with one side measuring 39.62 m. The building has ten loors with identical plan. The entire building is conditioned space with a total conditioned area of 15,717 sq m (all ten loors). The building is exposed on all the four sides. Windows on all four sides together constitute a WWR of 45%. There are permanent external shading devices designed for the proposed building. d. The HVAC design and consequently zoning for the proposed building have not been inalized hence according to Table 10.1 for each loor a simple core-perimeter zoning pattern, as shown in the Figure 10.1, has to be considered. The depth of perimeter zones is 5m as per guidance provided in this chapter. All the ive zones are considered to be conditioned ofice areas.

Figure 10.1: Five zone loor plate showing the perimeter and core zoning

e. Construction consists of typical reinforced cement concrete (RCC) column and beam structure with lat slab. External wall is made of brick with cement plaster. 45% of all faade area comprises of glazing that is lush with the external wall. Internal partition walls are designed as brick construction with cement plaster on both sides. No insulation is used in the roof and walls. f. Water-cooled centrifugal chillers are proposed to meet the cooling requirements of the building. All the spaces in the building will be served with variable air volume (VAV) air handlers. The system consists of chilled water circulation with evaporator, condenser and a chilled water circulation pump. Two chillers, each of 262 tons and with COP of 5.55 are proposed to meet the cooling requirements of the building. The fenestration consists of a double-glass unit in aluminum frame with the following properties: Table 10.7: Fenestration Summary Faade
North South East West

WWR
62% 25% 35% 55%

SHGC
0.36 0.36 0.23 0.36

The building design includes the following features, which incorporate some passive design methods to reduce energy consumption of the building in hot and dry climate (Ahmedabad) and still strive for a high WWR on certain facades to take advantage of daylight: The WWR on the northern faade is 65%. In a city like Ahmedabad, which is 23 N latitude, the sun rarely goes to the north of the building, hence there will be almost no direct light coming into the building from the North. North glazing brings in diffused light, which is preferred for ofice activity.

Energy Conservation Building Code (ECBC) User Guide

B.25

Appendix B: Whole Building Performance Method

The building has a WWR of 25% on the East side and a WWR of 55% on the West side. Ahmedabad being in a hot climate, the solar heat gain coeficient of the glass plays an important role. In this regard, the windows on East faade (where horizontal and vertical shading devices would not be very effective) of the building are proposed with a double glazed unit of low SHGC value of 0.23. Windows on the South, North and West facades have a double glazed unit with SHGC of 0.36. On the south faade of the building, overhangs of 0.6 m depth have been designed to reduce the direct light coming inside the building. To reduce high solar heat gain from the West side, vertical louvers/ins of 0.6 m width at a gap of 1.5 m are proposed. To take advantage of the high visible transmittance (0.62) of double glazed unit and high WWR in the North and the West facades, perimeter zones in these directions are equipped with daylight sensors that can dim the internal lighting in these zones. Steps for ECBC Compliance

Step 1: Ensure that the building design conforms to the local building bye laws and regulations
It is recommended to ensure that the building design conforms to the local building bye laws and regulations. The design team should request clear guidance from the local authorities on the following issues: Applicability of ECBC to the project Submittal requirements and procedure to apply for ECBC compliance Any local amendments to the ECBC that need to be followed Acceptability of the weather ile to the authorities

Step 2: Comply with the mandatory requirements of the ECBC

All the mandatory requirements of the ECBC code must be met by the project. The mandatory provisions of building envelope, HVAC, service hot water and pumping, lighting and electrical power are provided in sections 4.2, 5.2, 6.2, 7.2 and 8.2 respectively of the Code and must be complied with. It should be noted that even if the WBP method is adopted for ECBC compliance, mandatory requirements must still be followed even though one might not follow any or all of the prescriptive requirements.

Step 3: Create the Proposed Design Simulation Model

The simulation model should be developed as per the Proposed Design guidelines provided in Table 10.1 of the Guide. This table is an updated version of Table 10.1 of ECBC and provides detailed guidance to the users in creating both the Proposed and Standard Design. This section describes the methodology for creating the Proposed Design simulation model. All the assumptions while creating the model must be stated clearly and unambiguously and the simulation model of the Proposed Design should be prepared using approved simulation software. The simulation software must meet all the speciications listed in Section 10.2.1 of Appendix B of the Code. Building Envelope While modeling, the following should be noted: Walls within 45 degrees of each other can be combined into a single wall and assumed to have one orientation. The building in the Proposed Design case is to be modeled only for the actual designed orientation. All the building envelope materials in the simulation model shall be as per the Proposed Design of the

Energy Conservation Building Code (ECBC) User Guide

B.26

Appendix B: Whole Building Performance Method

building. Thermal speciications of walls must include thermal mass (speciic heat and density) as well as thermal resistance (U-factor or R-value). In this case study, the external wall section in the Proposed Design is a 230 mm brick wall with cement plaster on either side. If the manufacturer provides the material properties, they should, after veriication, be used to calculate the inal U-factor of the construction assembly. However, in this case study it is assumed that no data was available from the manufacturer. Thermo-physical properties of construction materials can be obtained from two sources: Appendix C of ECBC Libraries included in the simulation program For this case study, the properties of the speciied materials were derived from the simulation software library, which were assembled to form the building envelope. The resultant U-factor of the wall works out to be 2.02 W/m2K. Similarly, U-factor of the roof, which is an un-insulated RCC slab, works out to be 1.618 W/m2K. While modeling the facades of the building, the windows need to be modeled separately if the building uses daylight controls. Otherwise they can be combined (if they are in the same zone) into a larger effective window. Manually operated window-shading devices such as blinds or shades should not be modeled. However, any permanent shading devices such as ins, overhangs, and light-shelves have to be modeled as they have signiicant impact on the overall heat gain as well as daylight in the building. Since, India presently does not have a labeling program certifying the U-factor of the windows, the projects Proposed Design needs to comply with the requirement of the ECBC (for unrated vertical fenestration) as speciied in Table 11.1 of Appendix C. As per this table, the U-factor of the window assembly of the case study model is 5.1 W/m2K. Manufacturer has however provided the SHGC (0.36 and 0.23 for two types of glazing used in the building) and Visible Light Transmittance values (0.62 and 0.41 for two types of glazing). For exterior roofs other than roofs with ventilated attics, the relectance and emittance of the proposed roof surface, which can be derived from building material speciications, should also be modeled. For the case study, the roof surface has been modeled with a relectance of 0.45 since the relectance and emittance of the roof surface is exceeding the Code requirements as speciied in Table 10.1 (Building Envelope) of the Guide. Schedules Ofice schedule with varying occupancy from 7 am to 12 mid-night has been proposed for the building. Normal ofice schedule will be from 9 am to 6pm. Lighting For the Proposed Design: The design electric lighting power should be modeled accurately for the purpose of simulation. The lighting system power should include all lighting system components shown or provided for in the plans (including lamps, ballasts, task ixtures, and furniture-mounted ixtures). In cases where the electrical design includes lighting controls, they should be included in the simulation model. For the case study: An LPD value of 8.61 W/m2has been used in the ofice areas. Daylight sensors are proposed in the design of the lighting systems on the North and West facades.

Energy Conservation Building Code (ECBC) User Guide

B.27

Appendix B: Whole Building Performance Method

HVAC Zoning Where a complete HVAC system has been designed, the simulation model should be consistent with the design documents. It should relect the actual zoning scheme. For the case study: Since the HVAC zoning has not been designed/inalized, the ECBC User Guide mandates that a simple perimeter and core zoning should be done. The perimeter areas are modeled with a depth of 5 meters from exterior wall for four cardinal directions along with a central core area.

Figure 10.2: Simpliied Zoning of the Case Study Building when HVAC Zoning is Not Designed

HVAC Systems For the Proposed Design: The HVAC system should be speciied according to the mechanical layout of the design. All the inputs should be as per the designs, which include the fan and equipment eficiencies, static pressure, pump heads, etc. None of the default values by the software should be considered as input values for the above parameters unless they match the actual proposed values. When the HVAC system is designed, the system type and all actual component capacities and eficiencies should be modeled as per the actual system design. Any HVAC speciic energy-eficiency features, for example, economizers, variable-air-volume drives etc., should also be included in the simulation model as per the speciications in the design documents. For the case study, The building is served by VAV air-handling units, which are connected to the centrifugal chillers. Watercooled centrifugal chillers are proposed to meet the cooling requirements of the building. The system consists of chilled water circulation with evaporator, condenser and a chilled water circulation pump. Two chillers, each of 262 tons and with COP of 5.55 are proposed to meet the cooling requirements of the building. All the power and eficiencies of the system fan match with the Standard Design speciications. No savings is taken in the HVAC system design except the variable speed fan used in the water-cooled condenser in place of the two-speed fan in the Standard Design as the complete HVAC system is not designed in the case study.

Energy Conservation Building Code (ECBC) User Guide

B.28

Appendix B: Whole Building Performance Method

Miscellaneous Loads For the case study, an internal equipment load of 21.6 W/m2 has been considered for both the Proposed Design.

Step 4: Create the Standard Design simulation model

The simulation model should be developed as per the Standard Design guidelines provided in Table 10.1 of the Guide. The Standard Design model is created using the Whole Building Performance method speciied in ECBC. Once the model has been created, the simulation runs will show the energy consumption of the Standard Design building. The Standard Design is created with building speciications that comply with all prescriptive requirements of the ECBC. In the simulation model of the Standard Design, the glazing area is equally distributed on all sides of the building. For the Standard Design, the energy use shall be generated by simulating the building with its actual orientation and subsequently rotating the building by 90, 180 and 270 degrees. The energy use for the Standard Design will be obtained by taking an average of energy use from the simulation runs for four different orientations. Site and Climate All the input parameters in the Standard Design will be same as in the Proposed Design model. Building Envelope While modeling, the following should be noted:
Walls: The proposed building has two types of walls: external walls and internal partitions. Walls of the building

should be categorized based on their position within the building. Appendix A of the Code, deals with the deinitions of various kinds of walls in a building. The wall construction must comply with the prescriptive requirements of Section 4.3.2 of the Code. For the case study, since the building is in hot and dry climate and is a daytime use building, according to Table 4.3.2 of the Code, the U-factor of the wall shall be 0.44 W/m2K.
Roof: The roof construction must comply with the prescriptive requirements of Section 4.3.1 and 4.3.2 of the Code. For the case study, a mass construction roof with a U-factor of 0.409 W/m2 .K has been speciied in the Standard Design model. Table 10.1 provides guidance on how to model the relectivity of the roof. Windows:

In the Standard Design: Windows in all the directions have the same prescriptive requirements for SHGC and the U-factor. Windows should be equally distributed on all the sides. U-factor and the SHGC requirements depend on the window wall ratio (WWR) and the climate zone. The U-factor, SHGC and Visible Light Transmittance of the glass must meet the requirements set forth in Section 4.3.3 of the Code. Shading should not be modeled, whether internal or external. Self-shading of the building too shouldnt be modeled as per Table 10.1 (Building Envelope). For the case study: Since the Proposed Design has a WWR of 45%, as per Table 10.1 (Building Envelope) of the Guide, the WWR in the Standard Design shall be limited to 40%. All the windows in the Standard Design shall have a U-factor of 3.3 W/m2 .K and SHGC of 0.25 as per Table 4.3 of the Code.

Energy Conservation Building Code (ECBC) User Guide

B.29

Appendix B: Whole Building Performance Method

Space Use According to Appendix A of ECBC, the loor area of a building is categorized as conditioned-space, semiheated /cooled space or un-conditioned space. ECBC deines conditioned space as a cooled space, heated space, or directly conditioned space in the building. A semi-heated space is deined as an enclosed space within a building that is heated by a heating system whose output capacity is greater than or equal to 10.7 W/m2 of loor area but is not a conditioned space. An un-conditioned space is one that is not a conditioned space or a semi-heated space. Crawl spaces, attics, and parking garages with natural or mechanical ventilation are not considered as enclosed spaces. For the case study, the entire loor plate is assumed to be conditioned space. Lighting For the Standard Design: The lighting power density (LPD) should be speciied using either the Building Area method or the Space Function method. In Building Area method (Table 7.1 of ECBC) an average LPD value is deined for the entire building, whereas, in Space Function method (Table 7.2 of ECBC), individual spaces are assigned with different LPD values based on the activity within that space. For the case study: The Building Area method has been followed in the case study. A LPD of 10.8 W/m2 is considered in all the ofice areas as per Table 7.1 of ECBC, assuming all the areas to be ofice. HVAC Zoning This zoning pattern is the same for both Proposed Design and the Standard Design model. HVAC Systems For the Standard Design: As speciied in Table 10.2 of Appendix B of the Code, the HVAC system of the Standard Design model is based on: The building type: residential or non-residential The total built-up area excluding the parking area of the building For the case study: Based on the above two categories, the heating system of the Standard Design model is served by the Reheat Fan System (RHFS) Since the Proposed Design has a water cooled chiller, the Standard Design will also have water cooled centrifugal chiller as speciied in the footnote of Table 10.2 of Appendix B of the Code. In the Proposed Design there is no heating system provided for the building. However, since the Standard Design should also be modeled with heating, the same kind of provision is assumed for the Proposed Design simulation model as well. The Standard Design, consists of a centrifugal chiller which is water cooled with a variable air volume (VAV) AHU for each zone. The cooling type is chilled water and the heating is provided by electric resistance. Fans and controls: As speciied in the mandatory provisions given in Section 5.2.3 of the Code, all the mechanical cooling and heating systems should be controlled by respective schedules and set-point temperatures. The supply fans should be controlled by variable speed drives as speciied in Section 5.3.2.

Energy Conservation Building Code (ECBC) User Guide

B.30

Appendix B: Whole Building Performance Method

Number of Chillers and Sizing: For the Standard Design: The size of the chiller, which decides the COP of the chiller as per Table 5.1 of the Code is given in accordance with the following table. To decide the size of the chiller, a sizing run for the Standard Design is performed. The sizing ratios for this model would be 15% oversized for the cooling and 25% oversized for the heating unit as mentioned in the Code. . In cases, where HVAC eficiency values are not speciied in the Code, they should be referred to Appendix Go of ASHRAE 90.1-2004. If values are speciied neither in ECBC nor in ASHRAE 90.12004, they should be taken from the Proposed Design. For the case study: Table 10.3 of the Guide has been followed for determining the number of the chillers and their sizes in the case study building. The system consists of chilled water circulation with evaporator, condenser and a chilled water circulation pump. Two chillers, each of 232 tons and with COP of 5.55 are proposed to meet the cooling requirements of the building Service Hot Water When there is service hot water supply for the Proposed Design, similar system must be modeled in the Standard Design model. In this case study, since the Proposed Design is not a residential, hotel or hospital building, 20% of design loads are not required to be met by solar hot water system. The system eficiencies shall be as per Section 6.2.2 of the Code. Miscellaneous Loads The equipment loads in the Standard and the Proposed Design shall be modeled in the same way.

Step 5: Compare the Energy consumption in the Proposed Design with that of Standard Design
A review of the detailed inputs of both the Standard Design model and the Proposed Design model shows that the building does not meet the U-factor requirements for the wall as speciied in the prescriptive table of ECBC. Since the fenestration is unlabeled, the resultant U-factor of the complete window assembly is also high when compared with the U-factor of the Standard Design simulation model. However the internal lighting load is 20% less in the Standard Design model. A glass of higher SHGC has been used on the West, South and North side of the building and a glass of SHGC lesser than the base case has been used on the East facade. The windows are designed in such a way that mainly diffused light get into the building from the North faade. West faade has a high WWR of 55% but because there is good shading provided in the form of vertical ins, the effect of high WWR has been compensated to a certain extent. Also, as the building is a daytime ofice use building, the effect of West sun would be mainly in the unoccupied hours. Both the Proposed Design Model and the Standard Design models are simulated and the results are analyzed to check for errors, if any. In some cases, there are instances when either the cooling set-point or the heating set-point temperatures are not met by the HVAC system or the plant. They are normally categorized as either system unmet or plant unmet hours, which state the number of hours the system or the plant was unable to meet the cooling or heating load. The maximum allowable unmet hours either for the Proposed Design or the for the Standard Design are 300 hours as per Appendix B of the Code and if the number of hours that loads are unmet by either the system or plant shows a difference of more than 50 hours between the Standard and Proposed Design models, the simulation results are not accepted as valid. The best way to deal with this issue is to conirm that the sizing method of both the Standard and Proposed Design is similar. It could also be the case that some part of the HVAC system is undersized and may require redesign. These models are reined and re-run and checked for all the compliance clauses again and if found in order, prepared for compliance documentation

Energy Conservation Building Code (ECBC) User Guide

B.31

Appendix B: Whole Building Performance Method

checks. Some key differences in modeling the Standard Design and the Proposed Design model are as follows: The Standard Design may differ from the Proposed Design model in the speciication of building envelope U-factors, glazing SHGC, lighting power density and mechanical eficiency of HVAC system. The other major difference is in the modeling of the glazing. In the Standard Design the glazing WWR is spread on all the faades equally, as speciied in the Building Envelope of Table 10.1 of Appendix B. Moreover, there is no self-shading of the building allowed as speciied in Table 10.1. No assumed eficiency measures should be modeled over the Proposed Design to meet or to perform better than Standard Design. However eficiency options, which are designed for implementation in the proposed building can be included in the Proposed Design simulation model.

Step 6: Not needed Step 7: Not needed Step 8: Not needed Step 9: Prepare the compliance documents
For the project to inally comply with the Code, the required compliance documents should be prepared and iled as submittals to show that the Proposed Design consumes energy less than or equal to the Standard Design model. Table 10.8 provides Whole Building Performance compliance report making it easier for users to show compliance. Table 10.8: Building Energy Model Information Whole Building Performance Method Compliance Report
Project Name Project Address Designer of Record: Contact person: City: Weather Data: Climate Zone:
IT Park

Date: June 2009 Telephone: Telephone:

Ahmedabad Ahmedabad - IWEC weather data Hot and dry

Total Conditioned Area (sq ft)

15,717 sqm

Total Unconditioned Area (sq ft)

0 sqm

Total Floor Area (sq ft)

15,717 sqm

Advisory messages
Proposed Design Number of hours of heating loads unmet (system/plant) Number of hours of cooling loads unmet (system/plant) Number of warnings Number of errors Number of defaults overridden
0 hours 52 hours 12 0

Standard Design
0 hours 44 hours 12 0

Difference
0 hours 8 hours 0 0

Additional Building Information

Number of loors Simulation program
G+9 Visual DOE 4.1.2 based on DOE 2.1 E

Comparison of Input Parameters in Proposed Design and Standard Design

Energy Conservation Building Code (ECBC) User Guide

B.32

Appendix B: Whole Building Performance Method

Building Element Envelope

Above Grade Wall Construction(s) Below Grade Wall Construction Roof Construction

Proposed Design Input

U value 2.02 W/m2 .K ( 230 mm thick wall + Cement motar either side) U value 1.618 W/m2 .K (150 mm RCC slab+ Cement motar either side) NA NA 40% U factor=5.1 W/m2 .K SHGC1 = 0.23, SHGC2= 0.36 VLT1 = 0.41, VLT2= 0.62 0.6 m ixed overhangs on South & 0.6 m wide vertical ins on West side None

Standard Design Input

U value 0.44 W/m2 .K ( 230 mm thick wall + Insulation) (outside to inside) U value 0.409 W/m2 .K (Insulation +150 mm RCC slab) (outside to inside) NA NA 45% U factor =3.3 W/m2 .K SHGC = 0.25 NA None None

Exterior Floor Construction Slab-on-Grade Construction Window-to-Gross Wall Ratio Fenestration Type(s) Fenestration Assembly U Factor Fenestration Assembly SHGC Fenestration Visual Light Transmittance Fixed Shading Devices Automated Movable Shading Devices

Electrical System & Process Loads

Ambient lighting power density and Lighting Design Description. Process Lighting Lighting occupant Sensor Controls Day lighting Controls Receptacle Equipment Elevators or Escalators Refrigeration Equipment Other Process loads None In North and West perimeter zones 21.6 W/m2 None None 21.6 W/m2 8.61 W/m2 10. 8 W/m2

Mechanical & Plumbing Systems HVAC System Type (s)

Design Supply Air Temperature Differential Fan Control Fan Power Economizer Control Demand Control Ventilation Unitary Equipment Cooling Eficiency Unitary Equipment Heating Eficiency Chiller Type, Capacity, And Eficiency Cooling Tower Boiler Eficiency Chilled Water loop and Pump Parameters Condenser Water loop and Pump Parameters

Variable Air Volume

VSD control 0.0012 bhp/cfm None None NA NA 2 x 262 tons Water cooled centrifugal chiller COP 5.55 One two cell, with VSD control Pump head = 9.2 m; Eficiency = 0.9 Pump head = 4.5 m; Impeller eficiency 0.77 Motor eficiency = 0.9 Flow 3 gpm/ton -

Constant Air Volume

VSD control 0.0012 bhp/cfm None None NA NA 2 x 232 tons Water cooled centrifugal chiller COP 5.55 One two cell, with two speed control Pump head = 9.2 m; Eficiency = 0.9 Pump head = 4.5 m; Impeller eficiency 0.77 Motor eficiency = 0.9 Flow 3 gpm/ton -

Hot Water Loop and Pump Parameters Domestic Hot Water pump Parameters

Energy Conservation Building Code (ECBC) User Guide

B.33

Appendix B: Whole Building Performance Method

End use

Standard Design - End Use Summary 0 rotation 90 rotation 180 rotation 270 rotation
Energy Energy Peak Energy Peak Energy Peak Energy Type (kWh) (kW) (kWh) (kW) (kWh) (kW) (kWh) Peak (kW)
152.1 -

Average
Energy (kWh)
492,303 -

Peak (kW)
152.1 -

Interiors Lighting Interior lighting (Process) Exterior Lighting Space heating (Fuel 1) Space heating (Fuel 2) Space Cooling Pumps Heat Rejection Fans Interior Fans Parking garage Service Water Heating (Fuel 1) Service Water Heating (Fuel 2) Receptacle Equipment Refrigeration (Food, etc.,) Cooking (commercial, fuel 1) Cooking (commercial, fuel 2) Elevators and Escalators Other Process Total Building Consumption/ Demand Total Process Energy

Elec Elec Elec Natural Gas Elec Elec Elec Elec Elec Elec Natural Gas Elec

492,303 -

152.1 -

492303 --

152.1 -

492303 -

152.1 -

492303 -

3,065 817,716 10,922 44,840 261,403 -

110.1 338.1 4.5 16.2 163.2 -

3,252 815,756 10,894 44,766 260,962 -

108.4 338.1 4.5 16.2 163.2 -

3,389 815,690 10,893 44,768 260,769 -

109.7 338.1 4.5 16.2 163.1 -

3,164 816,411 10,903 44,776 261,215 -

108.8 338.1 4.5 16.2 163.2 -

3,218 816,393 10,903 447,88 261,087 -

109.25 338.1 4.5 16.2 163.175 -

11,324

4.4

11,324

4.4

11,324

4.4

11,324

4.4

11,324

4.4

Elec Elec Elec

984,607 -

304.2 -

984,607 -

304.2 -

984,607 -

304.2 -

984,607 -

304.2 -

984,607 -

304.2 -

Elec

Elec Elec Elec

2626180

1091.1

2623743

1091.5

2624623

1091.925

1092.8 2623864

1092.3 2624703

Elec

984607

304.2

984607

304.2

984607

304.2

984607

304.2

984607

304.2

Energy Summary by End Use Proposed Design

End Use
Interior Lighting (Ambient) Interior lighting (Process) Exterior Lighting Space Heating (fuel 1)

Standard Design Peak (kW)

97.9

Energy Type
Electricity Electricity Electricity Natural gas

Energy (kWh)
328,049

Energy (kWh)
492,303

Peak (kW)
152.1

Energy (%)
33.36%

Energy Conservation Building Code (ECBC) User Guide

B.34

Appendix B: Whole Building Performance Method

Space Heating (fuel 2) Space Cooling Pumps Heat Rejection Fans - Interior Fans-Parking Garage Service Water Heating (fuel 1) Service Water Heating (fuel 2) Receptacle Equipment Refrigeration (food, etc.,) Cooking (commercial, fuel 1) Cooking (commercial, fuel 2) Elevators and Escalators Other Process

Electricity Electricity Electricity Electricity Electricity Electricity Natural Gas Electricity Electricity Electricity Natural Gas Electricity Electricity Electricity

3,527 896,924 11,954 48,025 299,416 11,324 984,607 2583,826

97.9 381.9 5.1 18.3 150.3 4.4 304.2 1060

3,218 816,393 10,903 44,788 261,087 11324 984,607 2624,623

109.25 338.1 4.5 16.2 163.17 4.4 304.2 1091.9 -9.86% -9.64% -7.23% -14.68% 0% 0% 1.55%

Total Building Consumption

Proposed Design
Type Nonrenewable (Regulated & Unregulated)
Electricity Natural Gas Steam or Hot water Chilled Water Other Total Nonrenewable Regulated & Unregulated) 2583,826 2583,826

Standard Design
Energy Use (kWh)
2624,623 2624,623

Percentage Improvement
Energy Use (%)
1.55% 1.55%

Energy Use (kWh)

Energy Conservation Building Code (ECBC) User Guide

B.35

Appendix C: Default Values For Typical Constructions

APPENDIX C: Default Values for Typical Constructions

11.1 Procedure for Determining Fenestration Product U-Factor and Solar Heat Gain Coeicient
4.2.1.1 and 4.2.1.2 require that U-factors and solar heat gain coeficients (SHGC) be determined for the overall fenestration product (including the sash and frame) in accordance with ISO 15099. The building envelope trade-off option in 4.4 requires the use of visible light transmittance (VLT). In several cases, ISO 15099 suggests that individual national standards will need to be more speciic and in other cases the ISO document gives users the choice of two options. This section clariies these speciic issues as they are to be implemented for this code: a. 4.1 of ISO 15099: For calculating the overall U-factor, ISO 15099 offers a choice between the linear thermal transmittance (4.1.2) and the area weighted method (4.1.3). The area weighted method (4.1.3) shall be used b. 4.2.2 of ISO 15099: Frame and divider SHGCs shall be calculated in accordance with 4.2.2 c. 6.4 of ISO 15099 refers the issue of material properties to national standards. Material conductivities and emissivities shall be determined in accordance with Indian standards d. 7 of ISO 15099 on shading systems is currently excluded e. 8.2 of ISO 15099 addresses environmental conditions. The following are deined for India: For U-factor calculations:
Tin = 24C Tout = 32C V = 3.35 m/s Trm,out=Tout Trm,in=Tin Is=0 W/m2 For SHGC calculations: Tin = 24C Tout = 32C V = 2.75 m/s Trm,out=Tout Trm,in=Tin Is=783 W/m2

f. 8.3 of ISO 15099 addresses convective ilm coeficients on the interior and exterior of the window product. In 8.3.1 of ISO 15099, simulations shall use the heat transfer coeficient based on the center of glass temperature and the entire window height; this ilm coeficient shall be used on all indoor surfaces, including frame sections. In 8.3.2 of ISO 15099, the formula from this section shall be applied to all outdoor exposed surfaces g. 8.4.2 of ISO 15099 presents two possible approaches for incorporating the impacts of self-viewing surfaces on interior radiative heat transfer calculations. Products shall use the method in 8.4.2.1 of ISO 15099 (Two-Dimensional Element to Element View Factor Based Radiation Heat Transfer Calculation). The alternate approach in 8.4.3 of ISO 15099 shall not be used

Energy Conservation Building Code (ECBC) User Guide

C.1

Appendix C: Default Values For Typical Constructions

11.2 Default U-factors and Solar Heat Gain Coeicients for Unrated Fenestration Products
All fenestration with U-factors, SHGC, or visible light transmittance determined, certiied, and labeled in accordance ISO 15099 shall be assigned those values.

11.2.1 Unrated Vertical Fenestration

Unlabeled vertical fenestration, both operable and ixed, shall be assigned the U-factors, SHGCs, and visible light transmittances in Table 11.1 Table 11.1: Defaults for Unrated Vertical Fenestration (Overall Assembly including the Sash and Frame) Frame Type
All frame types Wood, vinyl, or iberglass frame

Glazing Type
Single Glazing Double Glazing

Clear Glass U-factor SHGC (W/m2 K)

7.1 3.3 5.1 0.82 0.59 0.68

VLT
0.76 0.64 0.66

Tinted Glass U-factor SHGC VLT 2 K) (W/m

7.1 3.4 5.1 0.70 0.42 0.50 0.58 0.39 0.40

Metal and other frame type Double Glazing

11.2.2 Unrated Sloped Glazing and Skylights

Unrated sloped glazing and skylights, both operable and ixed, shall be assigned the SHGCs and visible light transmittances in Table 11.1. To determine the default U-factor for unrated sloped glazing and skylights without a curb, multiply the values in Table 11.1 by 1.2. To determine the default U-factor for unrated skylights on a curb, multiply the values in Table 11.1 by 1.6.

11.3 Typical Roof Constructions

For calculating the overall U-factor of a typical roof construction, the U-factors from the typical wall construction type and effective U-factor for insulation shall be combined according to the following equation: 1 U Total Roof = 1 1 +U U
Typical Roof Typical Insulation

where UTotal Roof UTypical Roof UTypical Insulation : Total U-factor of the roof with insulation : U-factor of the roof : U-factor of the effective insulation from Table 11.2

Table 11.2: Defaults for efective U-Factor for Exterior Insulation layers (under review) Thickness
15 mm (0.5) 20 mm (0.75) 25 mm (1.0) 40 mm (1.5) 50 mm (2.0) 65 mm (2.5) 75 mm (3.0)

R-value
0.70 (4) 1.06 (6) 1.41 (8) 2.11 (12) 2.82 (16) 3.52 (20) 3.70 (21)

U-factor (W/m2K)
1.420 0.946 0.710 0.568 0.406 0.284 0.270

Energy Conservation Building Code (ECBC) User Guide

C.2

Appendix C: Default Values For Typical Constructions

11.4 Typical Wall Constructions

For calculating the overall U-factor of a typical wall construction, the U-factors from the typical wall construction type and effective U-factor for insulation shall be combined according to the following equation: 1 U Total Wall = 1 1 +U U
Typical Wall Typical Insulation

where UTotal Wall UTypical Wall UTypical Insulation : Total U-factor of the wall with insulation : U-factor of the wall from : U-factor of the effective insulation from Table 11.3 or Table 11.4

Table 11.3: Defaults for efective U-factor for Exterior Insulation Layers (under review) Thickness
15 mm (0.5) 20 mm (0.75) 25 mm (1.0) 40 mm (1.5) 50 mm (2.0) 65 mm (2.5) 75 mm (3.0)

R-value
0.70 (4) 1.06 (6) 1.41 (8) 2.11 (12) 2.82 (16) 3.52 (20) 3.70 (21)

U-factor (W/m2K)
1.262 0.874 0.668 0.454 0.344 0.277 0.264

Energy Conservation Building Code (ECBC) User Guide

C.3

Appendix D: Building Envelope Tradeoff Method

APPENDIX D: Building Envelope Tradeof Method

12.1 The Envelope Performance Factor
12.1.1 The envelope performance factor shall be calculated using the following equations.
Equation 12 1: where EPFTotal = EPFRoof + EPFWall + EPFFenest EPFRoof = C Roof / U S A S
S=1 n

EPFWall = C Wall,Mass / U S A S + C Wall, Other / U S A S

S=1 n S=1 n

EPFFenest = C 1Fenest, North / SHGC W M W A W + C 2 Fenest, North / U W A W +

W=1 n W=1 n

C 1Fenest, NonNorth / SHGC W M W A W + C 2 Fenest, NonNorth / U W A W + C 1Fenest, Skylight / SHGC S M S A S + C 2 Fenest, Skylight / U S A S
S=1 S=1 W=1 n W=1 n

where EPFRoof As, Aw SHGCw Mw Us CRoof CWall C1 Fenest C2 Fenest : Envelope performance factor for roofs. Other subscripts include walls and fenestration. : The area of a speciic envelope component referenced by the subscript s or for windows the subscript w. : The solar heat gain coeficient for windows (w). SHGCs refers to skylights. : A multiplier for the window SHGC that depends on the projection factor of an overhang or sidein. : The U-factor for the envelope component referenced by the subscript s : A coeficient for the Roof class of construction : A coeficient for the Wall : A coeficient for the Fenestration 1 : A coeficient for the Fenestration 2

Values of c are taken from Table 12.1 through Table 12.5 for each class of construction. Table 12.1: Envelope Performance Factor Coeicients-Composite Climate (under review) Daytime Occupancy
U-factor
Mass Walls Curtain Walls, Other 6.01 15.72

24-Hour Occupancy
U-Factor
13.85 20.48

SHGC
-

SHGC
-

Energy Conservation Building Code (ECBC) User Guide

D.1

Appendix D: Building Envelope Tradeoff Method

Roofs North Windows Non-North Windows Skylights

11.93 -1.75 -1.25 -96.35

40.65 54.51 311.71

24.67 -4.56 0.68 -294.66

58.15 86.57 918.77

Table 12.2: Envelope Performance Factor Coeicients-Hot Dry Climate (under review) Daytime Occupancy
U-factor
Mass Walls Curtain Walls, Other Roofs North Windows Non-North Windows Skylights 5.48 6.38 11.14 -2.40 -1.86 -96.27

24-Hour Occupancy
U-Factor
15.01 22.06 25.98 -1.49 1.187 -295.81

SHGC
36.57 46.79 309.33

SHGC
56.09 81.79 923.01

Table 12.3: Envelope Performance Factor Coeicients-Hot Humid Climate (under review) Daytime Occupancy
U-factor
Mass Walls Curtain Walls, Other Roofs North Windows Non-North Windows Skylights 6.42 14.77 9.86 -1.58 -1.00 -96.11

24-Hour Occupancy
U-Factor
9.60 19.71 14.11 -7.29 -6.48 -295.45

SHGC
34.95 43.09 305.45

SHGC
64.19 76.83 893.55

Table 12.4: Envelope Performance Factor Coeicients-Moderate Climate (under review) Daytime Occupancy
U-factor
Mass Walls Curtain Walls, Other Roofs North Windows Non-North Windows Skylights 2.017 2.72 5.46 -3.10 -2.98 -96.21

24-Hour Occupancy
U-Factor
3.11 4.11 5.86 -11.95 -11.62 -294.12

SHGC
29.66 34.86 298.82

SHGC
62.14 68.45 876.70

Table 12.5: Envelope Performance Factor Coeicients-Cold Climate (under review) Daytime Occupancy
U-factor
Mass Walls Curtain Walls, Other Roofs North Windows Non-North Windows Skylights 5.19 6.76 5.69 1.55 -1.13 -93.44

24-Hour Occupancy
U-Factor
5.19 6.76 5.67 1.55 -1.13 -93.44

SHGC
9.13 16.32 283.18

SHGC
9.13 16.32 283.18

12.1.2 Overhang and Side Fin Coeicients

The M multiplication factor can also be calculated using Equation 12 2. If the equation is used, a separate calculation shall be made for each orientation and unique shading condition. Equation 12 2: M = a PF 2 + b PF + 1

Energy Conservation Building Code (ECBC) User Guide

D.2

Appendix D: Building Envelope Tradeoff Method

Table 12.6: Overhang and Side Fin Coeicients Device

Overhangs Side Fins

Coeficient
A B A B

North
0.16 -0.61 0.23 -0.74

South
0.21 -0.83 0.12 -0.59

East/West
0.10 -0.58 0.14 -0.52

Example 12.1: Calculation Showing ECBC Compliance Using Trade-Of Option

Description of building:

Building size: 40m length, breadth 25m, 3m height, having 10sqm fenestration on each faade. Location: Hot and dry climatic zone Step 1: Determination of upper limit of envelope performance factor (EPF) for wall, roof and fenestration using prescriptive values: a) EPFRoof = C Roof / U S A S Us (from table 4.1)
S=1 n

= 0.261 (for 24 hr building) = 40 x 25 = 1000 m2 = 25.98 0.261 1000 = 6780.78

n n

As (as per geometry) EPFRoof

CRoof (from table 12.2) = 25.98 (for 24 hr building in hot and dry climate)

b) EPFWall = C Wall,Mass / U S A S + C Wall, Other / U S A S

S=1 S=1

(In this case it has been assumed that there is no curtain wall) Us (from table 4.2) As (as per geometry) EPFWall = 0.440 = 390 m2 = 15.01 0.44 390 = 2575.71

CWall (from table 12.2) = 15.01

Energy Conservation Building Code (ECBC) User Guide

D.3

Appendix D: Building Envelope Tradeoff Method

c) EPFFenest = C 1Fenest, North / SHGC W M W A W + C 2 Fenest, North / U W A W +

W=1 n W=1 n

C 1Fenest, NonNorth / SHGC W M W A W + C 2 Fenest, NonNorth / U W A W + C 1Fenest, Skylight / SHGC W M W A W + C 2 Fenest, Skylight / U S A S
W=1 S=1 W=1 n W=1 n

(Assuming there is no skylight and no shading device used on windows) UW (from table 4.3) MW = 3.3 = 1 (for no overhang case, in case of overhang, MW is to be calculated using table 12.6) and equation 12.2of ECBC = 56.09 = -1.49 = 81.79 = 1.187 SHGC (from table 4.3) = 0.25 (since WWR < 40%)

C1 Fenest, North (from table 12.2) C2 Fenest, North (from table 12.2) C1 Fenest,Non North(from table 12.2) C2 Fenest, Non North (from table 12.2) EPFFenest EPFTotal

= 56.09 0.25 10 + (-1.49) 3.3 10 + 81.79 0.25 30 + 1.187 3.3 30 = 821.98 = EPFRoof + EPFwall + EPFFenest = 6780.78 + 2575.71 + 821.98 = 10178.47

Step 2: Determination of EPF of proposed building using actual U-factors and SHGC. Assuming that in place of using Uroof of 0.261, the roof of proposed building has U-factor of 0.3. EPFroof new = 25.98 0.3 1000 = 7794 Similarly if U-factor of wall/fenestration and SHGC are different from prescriptive requirement, new EPFwall, EPFFenest are to be calculated. In this case, let us irst assume that the wall and fenestration meet the prescriptive requirements. The EPF of proposed building is: EPFTotal new = 7794 + 2575.71 + 821.98 = 11191.69 Step 3: Comparison of EPF through perspective route and EPFnew through actual speciications show the later is higher than the EPFperspective. Hence the building is not complying with the ECBC. Step 4: Now even with the roof having inferior U- value (0.4 against the requirement of 0.261), the EPF is to be brought down to the level of EPFperspective i.e. 10178.47 in this case. his may be done by several options related to wall or fenestration. In the example given above, through back calculation, it can be found that for bringing down the EPFnew to the level of EPFprescriptive= 10178.47 and with EPFRoof being 7794, and no change in fenestration, (EPFFenest
Energy Conservation Building Code (ECBC) User Guide D.4

Appendix D: Building Envelope Tradeoff Method

=821.98), the maximum EPFWall can be : EPFWall new = 10178.47 7794 -821.98 = 1562.02 Step 5: For the target EPFWall new =1562.02, the required UWall new can be calculated through back calculation:EPFwall Uwall = EPFWall = C Wall / U S A S
S=1 n

1562.01 15.01 # 390 = 0.266 This means that due to certain limitation if in place of having U-factors of roof equal to 0.261, it is kept as 0.3, as one option, U-factor of wall can be improved from 0.44 to 0.266 for complying with the code. Similar to the method of calculating revised U-factor for wall, other alternatives such as change in SHGC or change in UFenest can also be explored. = U Wall = Important: Change in speciication through trade-off method would vary from case-to-case and therefore need to be calculated separately for individual building and for individual solution.

12.1.3 Baseline Building Deinition

The following rules shall be used to deine the Baseline Building for Envelope Tradeoff: a. The Baseline Building shall have the same building loor area, gross wall area and gross roof area as the proposed design. If the building has both 24-hour and daytime occupancies, the distribution between these shall be the same as the proposed design b. The U-factor of each envelope component shall be equal to the criteria from 4.3 for each class of construction c. The vertical fenestration area shall be equal to the proposed design or 40% of the gross exterior wall area, which ever is less. The skylight area shall be equal to the proposed design or 5% of the gross exterior roof area, which ever is less d. The SHGC of each window or skylight component shall be equal to the criteria from 4.3

Energy Conservation Building Code (ECBC) User Guide

D.5

Appendix E: Climate Zone Map of India

APPENDIX E: Climate Zone Map of India

13.1 Climate Zones
he irst step in following the ECBC is determining the appropriate climate zone of the building site which will dictate the speciic requirements for design and construction of the building systems and components. India possesses a large variety of climates, which can be broadly categorized into ive regions with distinct climates. The ive climate zones, illustrated in the following map are normally designated as hot and dry, warm and humid, composite, temperate, and cold. The classiication of climate for different types of buildings is an aid to the functional design of buildings. Our country is zoned into several regions such that the differences of climate from region to region are capable of being relected in building design, warranting some special provision for each region. The signiicant difference in the climatic data across these zones deines unique thermal comfort requirements for buildings located in different zones. Following broadly highlights the differences in weather data in the ive climate zones and Table 13.2 provides a list of major cities in India with respect to their climate zones. These differences in the weather proile translate into unique requirements for building thermal comfort and architectural responses for the different climate zones. (See in Figure 13.1).

Figure 13.1: Climate Zone Map

Energy Conservation Building Code (ECBC) User Guide

E.1

Table 13.1: Classiications of Diferent Climate Zones in India Mean Temperature (C)
Summer Summer Winter midday night midday (High) (Low) (High)
40 to 45 20 to 30 5 to 25 0 to 10 15 to 20 Very Low 25-40% Low <500 mm/ yr. Cloudless skies with high solar radiation, causing glare Overcast (cloud cover ranging between 40 and 80%), causing unpleasant glare

Climate Zone
Winter night (Low) Diurnal Variation

Description

Mean Annual Sky Relative Precipitation Conditions humidity

Places

Appendix E: Climate Zone Map of India

Hot and Dry

High temperature | Low humidity and rainfall | Intense solar radiation and a generally clear sky | Hot winds during the day and cool winds at night | Sandy or rocky ground with little vegetation |Low underground water table and few sources of surface water. 30 to 35 25 to 30 25 to 30 20 to 25 5 to 8 High 70 to 90% High > 1200 mm/yr.

Rajasthan, Gujarat, Western Madhya Pradesh,Central Maharashtra etc. Kerela, Tamilnadu, Costal parts of Orissa and Andhra Pradesh etc. Mainly clear, Bangalore, Goa occasionally and parts of the overcast with Deccan dense low clouds in summer Clear with cloud cover < 50% / Overcast for most of the year Jammu &Kashmir, Ladakh, Himachal Pradesh, Uttaranchal, Sikkim, Arunachal Pradesh

Energy Conservation Building Code (ECBC) User Guide 30 to 34 17 to 24 27 to 33 16 to 18 8 to 13 High 60 to 85% High > 1000 mm/yr 17 to 24/20 to 30 4 to 11/17 to 21 (-7) to 8 /4 to 8 (-14) to 0 /(-3) to 4 25 to 25 /5 Low: 10Low: < to 15 50% /High: 200 mm/ 70-80% yr /Moderate 1000mm/yr 32 to 43 27 to 32 10 to 25 4 to 10 35 to 22 Variable Dry Periods= 20-50% Wet Periods= 50-95% Variable 5001300 mm/yr, during monsoon reaching 250 mm in the wettest month Variable Overcast and dull in the monsoon Uttar Pradesh, Haryana, Punjab, Bihar, Jharkhand, Chattisgarh, Madhya Pradesh etc.

Warm and Humid

Temperature is moderately high during day and night | Very high humidity and rainfall | Diffused solar radiation if cloud cover is high and intense if sky is clear | Calm to very high winds from prevailing wind directions | Abundant vegetation | Provision for drainage of water is required

Temperate

Moderate temperature | Moderate humidity and rainfall | Solar radiation same throughout the year and sky is generally clear | High winds during summer depending on topography | Hilly or high plateau region with abundant vegetation

Cold (Sunny/ Cloudy)

Moderate summer temperatures and very low in winter | Low humidity in cold/sunny and high humidity in cold/cloudy | Low precipitation in cold/ sunny and high in cold/cloudy | High solar radiation in cold/sunny and low in cold/cloudy | Cold winds in winter | Very little vegetation in cold/sunny and abundant vegetation in cold/cloudy

Composite This applies when 6 months or more do not fall within any of the above categories | High temperature in summer and cold in winter | Low humidity in summer and high in monsoons | High direct solar radiation in all seasons except monsoons high diffused radiation | Occasional hazy sky Hot winds in summer, cold winds in winter and strong wind in monsoons | Variable landscape and seasonal vegetation

Sources: Bansal and Minke (1988) Climatic zones and rural housing in India

Krishan et al. (2001). Climate responsive architecture: A design handbook for Energy-Eficient Buildings

E.2

Appendix E: Climate Zone Map of India

Table 13.2: Climate Zone of the Major Indian Cities Indian Cities and their respective Climatic Zones
City
Ahmedabad Allahabad Amritsar Aurangabad Bangalore Barmer Belgaum Bhagalpur Bhopal Bhubaneshwar Bikaner Bombay Calcutta Chitradurga Dehra Dun Dibrugarh Gauhati Gorakhpur Gwalior Hissar Hyderabad Imphal Indore Jabalpur Jagdelpur Jaipur Jaisalmer Jamnagar Jodhpur

Climatic Zone
Hot & Dry Composite Composite Hot & Dry Temperate Hot & Dry Warm & Humid Warm & Humid Composite Warm & Humid Hot & Dry Warm & Humid Warm & Humid Warm & Humid Composite Warm & Humid Cold Composite Composite Composite Composite Warm & Humid Composite Composite Warm & Humid Composite Hot & Dry Warm & Humid Hot & Dry

City
Jorhat Kota Kurnool Lucknow Madras Manglore Nagpur Nellore New Delhi Panjim Patna Pune Raipur Rajkot Ramgundam Ranchi Ratnagiri Raxaul Saharanpur Shillong Sholapur SunderNagar Surat Tezpur Tiruchchirapalli Trivandrum Tuticorin Veraval Vishakhapatnam

Climatic Zone
Warm & Humid Hot & Dry Warm & Humid Composite Warm & Humid Warm & Humid Composite Warm & Humid Composite Warm & Humid Composite Warm & Humid Composite Composite Warm & Humid Composite Warm & Humid Warm & Humid Composite Warm & Humid Hot & Dry Cold Hot & Dry Warm & Humid Warm & Humid Warm & Humid Warm & Humid Warm & Humid Warm & Humid

Energy Conservation Building Code (ECBC) User Guide

E.3

Appendix F: Air-Side Economizer Acceptance Procedures Envelope Summary

APPENDIX F: Air-Side Economizer Acceptance Procedures

14.1 Construction Inspection
Prior to Performance Testing, verify and document the following: System controls are wired correctly to ensure economizer is fully integrated (i.e. economizer will operate when mechanical cooling is enabled) Economizer lockout control sensor location is adequate (open to air but not exposed to direct sunlight nor in an enclosure; away from sources of building exhaust; at least 8 m [25 ft] away from cooling towers) System is provided with barometric relief, relief fan or return fan to control building pressure

14.2 Equipment Testing

Step 7: Simulate a cooling load and enable the economizer by adjusting the lockout control setpoint. Verify and document the following: Economizer damper modulates opens to 100% outside air Return air damper modulates closed and is completely closed when economizer damper is 100% open Economizer damper is 100% open before mechanical cooling is enabled Relief fan or return fan (if applicable) is operating or barometric relief dampers freely swing open Step 8: Continue from Step 1 and disable the economizer by adjusting the lockout control setpoint. Verify and document the following: Economizer damper closes to minimum ventilation position Return air damper opens to at or near 100% Relief fan (if applicable) shuts off or barometric relief dampers close. Return fan (if applicable) may still operate even when economizer is disabled

Energy Conservation Building Code (ECBC) User Guide

F.1

Appendix G: Compliance Forms

APPENDIX G: ECBC Compliance Forms

15.1 Envelope Summary
Envelope Summary
2005 India Energy Conservation Building Code Compliance Forms

ENVELOPE Summary
Draft 1, 27 March 2005

Project Info

Project Address

Date For Building Department Use

Applicant Name: Applicant Address: Applicant Phone:

Project Description Compliance Option

New Building Prescriptive

Addition

Alteration

Change of Use Systems Analysis

Envelope Trade-Off (Appendix D)

Hospital, hotel, call center (24 hour)

Other building types (daytime)

Vertical Fenestration Area Calculation

Note: Vertical fenestration area can not exceed 40% of the gross wall area for prescriptive option

Total Vertical Fenestration Area (rough opening)

divided by

Gross Exterior Wall Area

times 100 equals

% Vertical Fenestration

X 100 =
Total Skylight Area (rough opening) Gross Exterior Wall Area

Skylight Area Calculation

Note: Skylight area can not exceed 5% of the gross roof area for prescriptive compliance.

divided by

times 100 equals

% Skylight

X 100 =
Other building type (daytime)

Hospital, hotel, call center (24 hour)

OPAQUE ASSEMBLY
Roof Wall m Insulation R-value m Insulation R-value

OPAQUE ASSEMBLY
Roof Wall m Insulation R-value m Insulation R-value

FENESTRATION
Vertical Maximum U-factor Maximum SHGC (or SC) Overhang (yes or no) If yes, enter Projection Factor Side fins (yes or no) If yes, enter Projection Factor Skylight Maximum U-factor Maximum SHGC (or SC)

FENESTRATION
Vertical Maximum U-factor Maximum SHGC (or SC) Overhang (yes or no) If yes, enter Projection Factor Side fins (yes or no) If yes, enter Projection Factor Skylight Maximum U-factor Maximum SHGC (or SC)

Energy Conservation Building Code (ECBC) User Guide

G.1

Appendix G: Compliance Forms

15.2 Building Permit Plans Checklist

Building Permit Plans Checklist
2005 India Energy Conservation Building Code Compliance Forms

ENVELOPE Checklist
Draft 1, 27 March 2005

Project Address

Date

The following information is necessary to check a building permit application for compliance with the building envelope requirements in the 2005 India Energy Conservation Building Code. Applicability (yes, no, n.a.) Code Section Component Information Required Location on Plans Building Department Notes

MANDATORY PROVISIONS (Section 4.2)

4.2.1 4.2.1.1 4.2.1.2 4.2.1.3 4.2.2 4.2.3 Fenestration rating U-factor SHGC Air leakage Opaque U-factors Bldg. env. sealing Specify whether per 4.2.1.1 or default in Appendix C Specify whether per 4.2.1.2 or default in Appendix C Specify leakage rates Specify whether per default in Appendix C or ASHRAE Indicate sealing, caulking, gasketing, and weatherstripping

PRESCRIPTIVE COMPLIANCE OPTION (Section 4.3)

4.3.1 4.3.2 4.3.3 Roof Cool roof Roof Indicate R-values on roof sections Indicate minimum reflectance and emittance on plans Indicate R-values on wall sections (1) Indicate U-factors on fenestration schedule. Indicate if values are rated or default. If values are default, then specify frame type, glazing layers, gapwidth, low-e. (2) Indicate SHGC or SC on fenestration schedule. Indicate if values are rated or default. (3) Indicate if overhangs or side fins are used for compliance purposes. If so, provide projection factor calculation. (1) Indicate U-factors on fenestration schedule. Indicate if values are rated or default. If values are default, then specify frame type, glazing layers, gapwidth, low-e. (2) Indicate SHGC or SC on fenestration schedule. Indicate if values are rated or default.

4.3.4

Vertical fenestration

4.3.5

Skylights

BUILDING ENVELOPE TRADE-OFF OPTION (Section 4.4)

Provide calculations

Energy Conservation Building Code (ECBC) User Guide

G.2

Appendix G: Compliance Forms

15.3 Mechanical Summary

Mechanical Summary
2005 India Energy Conservation Building Code Compliance Forms

MECHANICAL Summary
Draft 1, 27 March 2005

Project Info

Project Address

Date For Building Dept. Use

Applicant Name: Applicant Address: Applicant Phone: 0 0

Project Description
Briefly describe mechanical system type and features.

Includes Plans FALSE

Compliance Option Equipment Schedules

Simple System

Complex System

Systems Analysis

The following information is required to be incorporated with the mechanical equipment schedules on the plans. For projects without plans, fill in the required information below.

Cooling Equipment Schedule

Equip. ID Brand Name Model No. Capacity kW Total L/s OSA CFM or Econo? SEER or EER IPLV Location

Heating Equipment Schedule

Equip. ID Brand Name Model No. Capacity kW Total L/s OSA cfm or Econo? Input kW Output kW Efficiency

Fan Equipment Schedule

Equip. ID Brand Name Model No. Total L/s SP kW Flow Control Location of Service

Energy Conservation Building Code (ECBC) User Guide

G.3

Appendix G: Compliance Forms

15.4 Mechanical Permit Checklist

Mechanical Permit Checklist
2005 India Energy Conservation Building Code Compliance Forms

MECHANICAL Checklist
Draft 1, 27 March 2005

Project Address

Date

The following information is necessary to check a building permit application for compliance with the mechanical requirements in the 2005 India Energy Conservation Building Code. Applicability (yes, no, n.a.) Code Section Component Information Required Location on Plans Building Department Notes

HEATING, VENTILATING, AND AIR CONDITIONING (Chapter 5) MANDATORY PROVISIONS (Section 5.2)
5.2.1 5.2.2 5.2.2.1 5.2.2.2 5.2.2.3 5.2.3 5.2.3.1 5.2.3.2 5.2.3.3 5.2.4 Equipment effficiency Provide equipment schedule with type, capacity, efficiency Controls Indicate thermostat with night setback, 3 different day types, and 2-hour manual override Indicate temperature control with 3 degree C deadband minimum Temp. & deadband Indicate two-speed motor, pony motor, or variable speed drive Clg.tower, fluid cooler to control the fans Timeclocks Piping & ductwork Piping insulation Ductwork insulation Ductwork sealing System balancing Indicate sealing, caulking, gasketing, and weatherstripping Indicate R-value of insulation Indicate R-value of insulation Specify sealing types and locations Specify system balancing

PRESCRIPTIVE COMPLIANCE OPTION (Section 5.3)

5.3 5.3.1 5.3.3.1 5.3.3.2 5.3.3.3 5.3.2 5.3.3.1 5.3.3.2 5.3.3.3 Economizer Air economizer Integrated operation Field testing Variable flow hydronic Pump flow rates Isolation valves Variable speed drive Indicate variable flow capacity on schedules Indicate two-way automatic isolation valves Indicate variable speed drive Indicate 100% capability on schedule Indicate capability for partial cooling Specify tests Indicate whether project is complying with ECBC Prescriptive Option OR with ASHRAE Standard 90.1-2004

SERVICE WATER HEATING AND PUMPING (Chapter 6) MANDATORY PROVISIONS (Section 6.2)
6.2.1 6.2.2 6.2.3 Solar water heating Provide calculations to justify capacity to meet 20% threshold

Equipment effficiency Provide equipment schedule with type, capacity, efficiency Piping insulation Indicate R-value of insulation Indicate heat trap on drawings or provide manufacturers specifications to show that equipment has internal heat trap Provide vapor retardant cover for pools Provide R-2.1 insulation

6.2.4 6.2.5 6.2.5

Heat traps Pool covers Pools over 32 C

Energy Conservation Building Code (ECBC) User Guide

G.4

Appendix G: Compliance Forms

15.5 Lighting Summary

Lighting Summary
2005 India Energy Conservation Building Code Compliance Forms

LIGHTING Summary
Draft 1, 27 March 2005

Project Info

Project Address

Date For Building Department Use

Applicant Name: Applicant Address: Applicant Phone: 0

Project Description

New Building

Addition

Alteration

Change of Use

Compliance Option Alteration Exceptions

(check box, if appropriate)

Prescriptive

Systems Analysis

Less than 50% of the fixtures are new and installed lighting wattage is not being increased

Maximum Allowed Lighting Wattage (Interior, Section 7.3)

Location (floor/room no.) Occupancy Description Allowed 2 Watts per m ** Area in m
2

Allowed x Area

** Document all exceptions

Total Allowed Watts

0.0 0.0 0.0 0.0

Watts Proposed

Proposed Lighting Wattage (Interior)

Location (floor/room no.) Fixture Description Number of Fixtures Watts/ Fixture

Total Proposed Watts may not exceed Total Allowed Watts for Interior

Total Proposed Watts

0.0 0.0 0.0 0.0

Maximum Allowed Lighting Wattage (Exterior, Section 7.4)

Location Description Allowed Watts 2 per m or per lm Area in m (or lm for perimeter)
2

Allowed Watts 2 x m (or x lm)

0.0 0.0 0.0 0.0 0.0 0.0

Watts Proposed

Total Allowed Watts

Proposed Lighting Wattage (Exterior)

Location Fixture Description Number of Fixtures Watts/ Fixture

Total Proposed Watts may not exceed Total Allowed Watts for Exterior

Total Proposed Watts

0.0 0.0 0.0 0.0

Energy Conservation Building Code (ECBC) User Guide

G.5

15.6 Lighting Permit Checklist

Lighting Permit Checklist
2005 India Energy Conservation Building Code Compliance Forms

LIGHTING Checklist
Draft 1, 27 March 2005

Project Address

Date

The following information is necessary to check a building permit application for compliance with the lighting requirements in the 2005 India Energy Conservation Building Code. Applicability (yes, no, n.a.) Code Section Component Information Required Location on Plans Building Department Notes

LIGHTING (Chapter 7) MANDATORY PROVISIONS (Section 7.2)

7.2.1 7.2.1.1 7.2.1.2 7.2.1.3 7.2.1.4 7.2.1.5 7.2.2 7.2.3 7.2.4 Controls Automatic shutoff Space control Daylight zones Ext. lighting control Additional control Tandem wiring Exit signs Indicate automatic shutoff locations or occupancy sensors Provide schedule with type, indicate locations Provide schedule with type and features, indicate locations Indicate photosensor or astronomical time switch Provide schedule with type, indicate locations Show wiring on schedule Indicate 5 watts maximum

Ext. bldg.grounds ltg. Indicate minimum efficacy of 60 lumens/Watt

PRESCRIPTIVE INTERIOR LIGHTING POWER COMPLIANCE OPTION (Section 7.3)

7.3 Indicate whether project is complying with the Building Area Method (7.3.1) or the Space Function Method (7.3.2) Provide lighting schedule with wattage of lamp and ballast and Building area method number of fixtures. Document all exceptions. Provide lighting schedule with wattage of lamp and ballast and Space function method number of fixtures. Document all exceptions. Luminaire wattage Indicate on plans

7.3.1

7.3.2 7.3.3

PRESCRIPTIVE EXTERIOR LIGHTING POWER COMPLIANCE OPTION (Section 7.4)

7.4 Provide lighting schedule with wattage of lamp and ballast and Building area method number of fixtures. Document all exceptions.

ELECTRICAL POWER (Chapter 8) MANDATORY PROVISIONS (Section 8.2)

8.2.1 8.2.2 8.2.3 8.2.4 Transformers Motor efficiency Provide schedule with transformer losses Provide equipment schedule with motor capacity, efficiency

Power factor correction Provide schedule with power factor correction Check metering Provide check metering and monitoring

Appendix G: Compliance Forms

15.7 Whole Building Performance Checklist

Whole Building Performance Method Compliance Report
Project Name Project Address Designer of Record: Contact person: City: Weather Data: Climate Zone: Date: Telephone: Telephone:

Total Conditioned Area (sq ft)

Total Unconditioned Area (sq ft) Advisory messages

Total Floor Area (sq ft)

Proposed Design Number of hours of heating loads unmet (system/plant) Number of hours of cooling loads unmet (system/plant) Number of warnings Number of errors Number of defaults overridden

Standard Design

Difference

Additional Building Information

Number of loors Simulation program

Building Element Envelope

Above Grade Wall Construction(s) Below Grade Wall Construction Roof Construction Exterior Floor Construction Slab-on-Grade Construction Window-to-Gross Wall Ratio Fenestration Type(s) Fenestration Assembly U Factor Fenestration Assembly SHGC

Comparison of Input Parameters in Proposed Design and Standard Design Standard Design Input Proposed Design Input

Fenestration Visual Light Transmittance Fixed Shading Devices Automated Movable Shading Devices

Electrical System & Process Loads

Ambient lighting power density and Lighting Design Description. Process Lighting Lighting occupant Sensor Controls Day lighting Controls

Energy Conservation Building Code (ECBC) User Guide

G.7

Appendix G: Compliance Forms

Receptacle Equipment Elevators or Escalators Refrigeration Equipment Other Process loads

Mechanical & Plumbing Systems HVAC System Type (s)

Design Supply Air Temperature Differential Fan Control Fan Power Economizer Control Demand Control Ventilation Unitary Equipment Cooling Eficiency Unitary Equipment Heating Eficiency Chiller Type, Capacity, And Eficiency Cooling Tower Boiler Eficiency Chilled Water loop and Pump Parameters Condenser Water loop and Pump Parameters Hot Water Loop and Pump Parameters Domestic Hot Water pump Parameters

Variable Air Volume

Constant Air Volume

End use

Standard Design - End Use Summary 0 rotation 90 rotation 180 rotation 270 rotation
Energy Energy Peak Energy Peak Energy Peak Energy Type (kWh) (kW) (kWh) (kW) (kWh) (kW) (kWh) Peak (kW)

Average
Energy (kWh) Peak (kW)

Interiors Lighting Interior lighting (Process) Exterior Lighting Space heating (Fuel 1) Space heating (Fuel 2) Space Cooling Pumps Heat Rejection Fans Interior Fans Parking garage Service Water Heating (Fuel 1) Service Water Heating (Fuel 2) Receptacle Equipment Refrigeration (Food, etc.,)

Elec Elec Elec Natural Gas Elec Elec Elec Elec Elec Elec Natural Gas Elec

Elec Elec

Energy Conservation Building Code (ECBC) User Guide

G.8

Appendix G: Compliance Forms

Cooking (commercial, fuel 1) Cooking (commercial, fuel 2) Elevators and Escalators Other Process Total Building Consumption/ Demand Total Process Energy

Elec

Elec

Elec Elec Elec

Elec

Energy Summary by End Use Proposed Design

End Use
Interior Lighting (Ambient) Interior lighting (Process) Exterior Lighting Space Heating (fuel 1) Space Heating (fuel 2) Space Cooling Pumps Heat Rejection Fans - Interior Fans-Parking Garage Service Water Heating (fuel 1) Service Water Heating (fuel 2) Receptacle Equipment Refrigeration (food, etc.,) Cooking (commercial, fuel 1) Cooking (commercial, fuel 2) Elevators and Escalators Other Process

Standard Design Peak (kW) Energy (kWh) Peak (kW) Energy (%)

Energy Type
Electricity Electricity Electricity Natural gas Electricity Electricity Electricity Electricity Electricity Electricity Natural Gas Electricity Electricity Electricity Natural Gas Electricity Electricity Electricity

Energy (kWh)

Total Building Consumption

Proposed Design
Type Energy Use (kWh)
2583,826 2583,826

Standard Design
Energy Use (kWh)
2624,623 2624,623

Percentage Improvement
Energy (%)
1.55% 1.55%

Nonrenewable (Regulated & Unregulated)

Electricity Natural Gas Steam or Hot water Chilled Water Other Total Nonrenewable Regulated & Unregulated)

Energy Conservation Building Code (ECBC) User Guide

G.9

Appendix H: Comparison of International Building Energy Standards

APPENDIX H: Comparison Of International Building Energy Standards1

uildings account for about one-third of all the energy consumption in the world, and much of this consumption footprint is locked in through the design and construction of the building.2 Building energy standards are an important tool to improve energy eficiency in new buildings. For example, Chinas residential energy standard requires new buildings to be 65% more eficient than buildings from the early 1980s. In the U.S., building energy codes3 save over $1 billion in energy costs per year, and this igure is growing.4 Denmark adopted one of the irst comprehensive building energy codes in 1961, and it has seen average household energy consumption per unit of space drop substantially since then. 5 Building energy standards set requirements for how energy-eficient a building will be. Standards vary quite a bit between countries in several respects including the extent of their coverage, the speciic requirements, means of attaining compliance and the enforcement system. This summary provides an overview of some key trends in building energy standards, and what this may mean for India. Extent of Coverage Building energy standards at a minimum usually cover insulation and thermal and solar properties of the building envelope (the walls, roofs, windows and other points where the interior and exterior of a building interface). Most standards also cover heating, ventilation, and air conditioning, hot water supply systems, lighting, and electrical power. Some cover additional issues such as the use of natural ventilation and renewable energy, and building maintenance. In some countries, not all the issues are considered in a single standard. For example, the Chinese standards include lighting in a separate document. Within these broad categories, there are also numerous differences in what the speciic requirements cover. Some countries have signiicant detail about the need to minimize condensation on insulation. Some countries (like India or Japan) have detailed requirements based on different types, sizes or orientations of buildings, for example, while others have simpler requirements for a broader range of buildings. The U.S., India, and Canada all have commercial building energy codes derived from standards produced by the American Society of Heating, Refrigerating and Air Conditioning Engineers (ASHRAE), although speciic requirements in each country vary. European Union countries are all required to adopt legislation harmonized with the Directive on Energy Performance in Buildings, which provides guidelines for the performance of buildings including the envelope, HVAC, lighting (in non-residential), building orientation and passive solar systems. Comparison of Elements Covered in Selected Commercial Building Standards and Codes Australia Canada Envelope HVAC Service Hot Water and Pumping Electrical Power Lighting Performance-Based Alternative

China
N.A. N.A. N.A., in a separate standard N.A.

India Japan Korea U.S. (ASHRAE 90.1 2007)

N.A.

1 2

3 4 5

Content Credit: M Evans, B Shui, A Delgado, Paciic Northwest National Laboratory (PNNL), USA. This report is primarily based on a series of country reports describing building energy codes in the Asia-Paciic region that the Paciic Northwest National Laboratory prepared with U.S. Department of Energy support under the Asia-Paciic Partnership on Clean Development and Climate. Some countries refer to their building energy regulations as codes and others call them standards. Please see www.energycodes.gov for details. Jens Lausten. 2008. Energy Eiciency Requirements in Building Codes, Energy Eiciency Policies for New Buildings. International Energy Agency, Paris.

Energy Conservation Building Code (ECBC) User Guide

H.1

Appendix H: Comparison of International Building Energy Standards

Not all standards and codes cover the same types of buildings either. For example, in India, the Energy Conservation Building Code (ECBC) covers commercial and multi-family residential buildings, but not small residential buildings; this is also true of the standards in Russia, Ukraine, and Kazakhstan, for example. In Japan, there are standards for both residential and commercial buildings, but the buildings must have at least 2,000 square meters of loor space to be covered. Most countries that regulate both commercial and residential construction for energy eficiency have separate standards for each, although countries categorize the buildings differently. In India, Australia, Canada, and the U.S., the codes consider commercial buildings to include multifamily residential buildings, while in China and Japan, the residential standards regulate such multi-family residences. This difference is important because typically the commercial building requirements are somewhat more complex and cover more issues than those for residential buildings. Speciic Requirements The actual eficiency requirements for new buildings vary between countries. While it would not be possible to highlight the full range of variation in a summary of this size, a few examples may help to illustrate this point. The table below highlights differences between the requirements for several building components in India, Australia, China and the U.S. Snapshot of Building Energy Eficiency: Maximum U-Factors and Lighting Power Densities in the U.S., China and India [Units: W/(mK) for U-factors] Building Components
Roof Wall Vertical Glass Windows (SHGC) Lighting Power Density (W/m)

U.S.
Miami
0.358 0.642 to 3.293 0.25 10.8

China
Hainan
0.9 1.5 0.35 to 0.60 11

India
New Delhi
0.409 for most buildings; 0.261 for 24-hr buildings 0.44 0.20 to 0.25 10.8

Australia
Darwin
0.313 0.556 0.09 7 or 10

Notes: This table assumes that we are comparing a 10-story commercial ofice building in similar climate zones in each country. The representative cities used for the comparison are Miami in the U.S., Hainan Province in China, and New Delhi in India. SHGC stands for solar heat gain coeficient and it represents the ratio of solar heat that can penetrate through a window. WWR stands for window to wall ratio. Sources: ASHRAE 90.1-2007, ECBC 2007, Chinas Design Standards for Energy Eficiency of Public Buildings 2005 and the Building Code of Australia 2007. In general, the lower the number represented in this chart, the more eficient the component will be. However, because this chart is looking at one building type in one climate zone, extrapolating these results to a national level requires some care. For example, the U.S. U-factors shown are quite different than the requirements applicable in other U.S. climate zones, where more eficient envelopes are mandatory. Means of Attaining Compliance Building energy standards typically provide property owners with some degree of lexibility in meeting the energy eficiency requirements. This is important because it means that the standard can be more stringent without impinging too severely on the ability of property owners to adapt buildings to their needs. There are several approaches to providing this lexibility. In many countries, including India, the U.S., Canada and Australia, the codes have four classes of requirements. The irst are mandatory requirements that must be satisied regardless of any other factors for a building to be considered in compliance. The majority of these codes are then made of up prescriptive requirements, which are similar to the mandatory requirements in that they provide speciic values and details. However, building designers may be allowed to trade-off some of the prescriptive requirements with others regarding the building envelope. The codes then provide rules on what can be traded-off and how. Finally, these codes also provide an option for compliance based on building energy performance instead of the prescriptive requirements. This last option would allow a building designer to install

Energy Conservation Building Code (ECBC) User Guide

H.2

Appendix H: Comparison of International Building Energy Standards

less eficient windows but a more eficient air conditioning system if the total designed energy use falls within the required norms. There are several approaches to establishing the baseline for comparison under the building energy performance method. The UK uses a total carbon footprint of the building (called the Carbon Index Rating)6, the U.S. uses the cost as its reference metric, while some other countries deine the characteristics of a reference building for the comparison. Korea takes a different approach, establishing mandatory requirements and points for a whole range of energy issues related to buildings. Each new building must have a minimum of 60 points. Buildings that exceed the minimum point requirement may be eligible for certain beneits, such as relaxation of certain zoning rules. Enforcement Systems Enforcement is critical for the standard to have an effect. Not all countries have mandatory building energy standards. India, for example, has a voluntary code. Japans standard is also technically voluntary, although Japan has recently adopted penalties for non-compliance that blur this distinction. The U.S., Canada, and Australia all adopt building standards at the local level. Not all jurisdictions in the U.S. and Canada have adopted their nations model building energy code. Some important issues regarding enforcement and the related impact of the code on energy use include: the point of compliance (design and/or construction stage), how buildings are checked and by whom, penalties and other incentives for compliance, training and information on the code, compliance tools such as code compliance software and inspection checklists, equipment and material testing and ratings. In the U.S., Canada, Australia, and Korea, for example, the building design must be approved and inspectors check the building for compliance at least once during construction. In Japan, parts of Europe, and the former Soviet Union, the checks only occur at the building design stage. China uses a combination of government employees and certiied companies to check building designs and inspect the buildings for compliance. There is no single answer as to which system produces the highest level of compliance. For example, Japanese oficials believe that Japan attains a high level of compliance in actual construction because Japan has a very well developed system of training and information dissemination on the building energy standards. Studies in the U.S. have shown that there, physical inspections result in much higher compliance rates. The stringency of the national system for testing materials and equipment for their energy eficiency properties can also have a marked impact on the inal energy consumption of a building. Most countries have a system of certiied laboratories that test materials and equipment (like windows and air conditioners), and rate them for eficiency. These ratings then determine if the equipment in a building meets the building energy standard. Testing procedures vary between countries, and there is anecdotal evidence that even in countries with well established systems, ratings can differ by 10% or more based on the testing procedures. Building energy standard compliance rates vary signiicantly between countries. What constitutes compliance may also vary, and not all countries consistently publish compliance data. That said, countries usually have lower compliance rates soon after they adopt or revise a standard, and when their enforcement system is not fully developed. Options for India to Consider India has taken a purposeful step toward improved building energy eficiency in adopting the Energy Conservation Building Code. The next step is implementing this code, which could require concerted efforts both at the state and national levels. States would need to decide to adopt the code. The national government could also help with this learning process by requiring that all new government buildings meet the building energy code. For example the national government might provide tools to help states and local jurisdictions with enforcement. India has a well-developed system to enforce other types of building codes, and it might use this system for enforcing the building energy code as well. Building energy inspectors at the local level might need training, and local jurisdictions could hire some staff to handle the additional workload. India could also try to simplify the implementation task by developing code compliance software that allows building developers and inspectors to
6 R.E. Horne et al. 2005. International Comparison of Building Energy Performance Standards. Centre for Design, RMIT University, Melbourne, Australia.

Energy Conservation Building Code (ECBC) User Guide

H.3

Appendix H: Comparison of International Building Energy Standards

easily check the building design for compliance. Such software could also be designed to automatically develop inspection checklists. As India gains experience with implementing its code, it might want to modify the code periodically. Many countries have found that establishing a regular timetable for such modiications can allow many stakeholders to have input into the process, which in turn, makes the code more feasible to implement. Indian consumers could beneit from this process as the energy costs in new buildings decline at the same time that the environmental footprint of these buildings grows smaller.

Energy Conservation Building Code (ECBC) User Guide

H.4

Appendix I: References

APPENDIX I: References
1. A. Bhatia: Course Content (PDH 149), HVAC Design Aspects: Choosing a Right System-Central V/s Compact Systems, Herndon, USA 2. ASHRAE/ANSI standard 62 (2004), Ventilation for Acceptable Indoor Air Quality, American Society of Heating, Refrigerating, and Air-conditioning Engineers, Atlanta, USA 3. ASHRAE / ANSI Standard 55 (2004), Thermal Environmental Conditions for Human Occupancy, American Society of Heating, Refrigerating, and Air-conditioning Engineers, Atlanta, USA 4. ASHRAE Handbook (2005): Fundamentals (SI), American Society of Heating, Refrigerating, and Airconditioning Engineers, Inc., www.ashrae.org, Atlanta, GA, USA 5. ASHRAE (2004, 2007): 90.1 User Manual-ANSI/ASHRAE/IESNA Standard 90.1-2004, American Society of Heating, Refrigerating, and Air-conditioning Engineers, Inc., www.ashrae.org, Atlanta, GA, USA 6. ASHRAE (2004): Energy Standard for Buildings Except Low-Rise Residential Buildings, American Society of Heating, Refrigerating, and Air-conditioning Engineers, Inc., www.ashrae.org, Atlanta, GA, USA 7. Bansal and Minke(1988), Climatic zones and rural housing in India, India 8. Bureau of Energy Eficiency, Ministry of Power, Government of India (2007): Energy Conservation Building Code (ECBC)-Revised Version May 2008, New Delhi, India 9. Bureau of Energy Eficiency, Ministry of Power, Government of India (2005): Energy Eficiency in Electrical Utilities, New Delhi, India 10. Bureau of Indian Standard (2005): National Building Code of India, Second Revision 2005, New Delhi, India 11. Donald R. Wulinghoff (1999): Energy Eficiency Manual, Energy Institute Press, Wheaton, Maryland, USA 12. Dr. Ardeshir Madhavi (1995): Fundamentals of Building Physics, Carnegie Mellon University, Pittsburgh, USA 13. E Source (2005): E Source Technology Atlas Series- Volume I: Lighting, Volume II: Commercial Space Cooling and Air Handling, Volume IV: Drive Power, Boulder, CO, USA. 14. Goetzler W (2007): Variable Refrigerant Flow Systems, ASHRAE Journal 49 (4) 15. Krishan et al. (2001): Climate responsive architecture, A design handbook for energy eficient buildings, School of Planning & Architecture (SPA), New Delhi, India 16. Ministry of Power (2001): Energy Conservation Act, www.powermin.nic.in, New Delhi, India. 17. Morrison F. (2004): Whats up with Cooling Tower, ASHRAE Journal 46 (7), USA. 18. Nayak and Prajapati (2006): Handbook on Energy Conscious Buildings, IIT Bombay, Bombay, India 19. Stein, B., Reynolds, J., Grondzik W., & Kwok, A (2005). Mechanical and Electrical Equipment for Buildings, 10th Ed. John Wiley & Sons Inc. 20. U.S. Department of Energy: EnergyPlus Energy Simulation Weather Data, www.eere.energy.gov, Washington DC 21. US Green Building Council (2006), LEED for new Construction, Reference Guide, Version 2.2, Third Edition, www.usgbc.org, Washington, DC, USA 22. USAID ECO-III Project: Energy Conservation Building Code Tip Sheet; Envelope, Lighting, HVAC, & Energy Simulation, www.eco3.org, New Delhi, India Web References: 1. Southface Energy Institute, www.southface.org, 241 Pine Street NE, Atlanta, USA

Energy Conservation Building Code (ECBC) User Guide

I.1

USAID ECO-III Project International Resources Group AADI Building, Lower Ground Floor 2, Balbir Saxena Marg, Hauz Khas, New Delhi-110016, India Phone: +91-11-2685-3110; Email: [email protected]; Web Site: www.eco3.org