All manuals and user guides at all-guides.

com

Comau Robotics
Instruction Handbook

m
.co
es
uid

Control Unit
-g

Standard Version

Maintenance
all

Help to problem-solving
Preventive maintenance plan to guarantee the C5G functionality over time
Preventive and special maintenance procedures
Spare part list

CR00757598_en-00/0411
 All manuals and user guides at all-guides.com

The information contained in this manual is the property of COMAU S.p.A.

Reproduction of text and illustrations is not permitted without prior written approval by COMAU S.p.A.

COMAU S.p.A. reserves the right to alter product specifications at any time without notice or obligation.

Copyright © 2008-2011 by COMAU - Date of publication 04/2011

 All manuals and user guides at all-guides.com

SUMMARY

1. GENERAL SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...9

Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Applicability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2. MAINTENANCE PRESCRIPTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...19

Precautions before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Precautions while carrying out maintenance activities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Precautions at the end of the maintenance activities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Maintenance staff. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Equipment and tools necessary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Torque wrench settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3. HELP IN TROUBLE SHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...21

Precautions before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Methodology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Problem analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Diagnosis messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Identification items and abbreviations for connectors, cables and modules . . . . . . . . . . . . . 25
Traceability for replacement purposes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Replacing the components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Control Unit outline diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Comau Customer Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4. SWITCHING OFF THE POWER SUPPLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...30

Precautions and risks associated to the power supply off-switching . . . . . . . . . . . . . . . . . . . . . 30
Switching off the power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5. HOW TO REACH THE MODULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...34

Precautions before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Risks associated with the module reaching procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Module location and reaching methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

_LB-RC-C5E-MAN_enTOC.fm
00/0000 3
 All manuals and user guides at all-guides.com

Front door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Upper panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

6. HOW TO MOVE THE ROBOT WHEN THE CONTROL UNIT IS DAMAGED . . . . . . ..39
Precautions before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Risks associated with the Robot handling with Control Unit disconnected . . . . . . . . . . . . . . . . 39
How to use the Brake Release module C5G-OBR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

7. PREVENTIVE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..43

Precautions before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Equipment and tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Preventive maintenance plan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
ACC: door closing and seal efficiency check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
ACO: cleaning the condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
ACO: emptying the condensate collectiong can . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
E110: fan cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
E111..E114: fan cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
UPS: replacing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

8. SPECIAL MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..56

Precautions before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Equipment and tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Modules subject to special maintenance activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
ACO: replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
AMS-APC820: module replacement and Compact Flash recovery . . . . . . . . . . . . . . . . . . . . . . 63
AMS-ASM32: module replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
AMS-IAM: module replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
AMS-PPS8: module replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
HMK: replacing the hour-counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
SDM: module replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
UPS: replacing the module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

9. SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..91

Precautions about the spare part usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Where to procure the spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

_LB-RC-C5E-MAN_enTOC.fm
4 00/0000
 All manuals and user guides at all-guides.com

Spare part list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Spare parts for the C5G basic model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

10. SETTING OUT OF WORK AND DISMANTLING . . . . . . . . . . . . . . . . . . . . . . . . . . . ...97

Precautions before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Staff to set the plant out of work and dismantle it . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Equipment and tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Setting out of work and dismantling procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Removing the pile and battery from the Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

_LB-RC-C5E-MAN_enTOC.fm
00/0000 5
 All manuals and user guides at all-guides.com

Preface

PREFACE
This chapter deals with the following topics:
– Reference documents
– Content of the C5G Control Unit manuals

m
– Document preservation
– Manual content limits
– Symbols in the manual.

Reference documents
.co
This document refers to the C5G Control Unit.
The complete set of manuals concerning the C5G control units consists of:
es
Comau C5G Control Unit – Technical Specification
– Transport and installation
– Maintenance
– Control Unit use
Circuit Diagram – Circuit Diagram (ver. ACC1 and ACC3)
uid

– Circuit Diagram (ver. ACC5)

– Circuit Diagram (ver. PAL)

Those manuals are to be supplemented by the following documents:

Comau Robot – Technical Specifications *¹

-g

– Transport and installation *¹

– Maintenance *¹
Programming – PDL2 Programming Language Manual
– VP2 - Visual PDL2
all

– Motion programming
Applications – According to the required application
type.
*¹ specific for the installed Robot type

The above mentioned manuals shall be preserved in good repair for the entire
Robot System operating life and shall always be available for the staff members
carrying out activities on the Robot System.

HS-RC-C5E-0_01.fm
00/0211 6
 All manuals and user guides at all-guides.com

Preface

Content of the C5G Control Unit manuals

Device Manuals Contents

C5G Control – Technical – Description and main features of the Control Unit
Unit Specification – Guide to Control Unit model selection
– General description about the expanding possibilities in
relation to I/O signals, communication networks and safety
devices
– Description and purchase codes for the Control Unit and its
optionals.
– Transport and – Information about the preparing activities and
installation prearrangements required to install the C5G
– Dimensions and weights, transport and lifting methods
– Procedures to adapt the internal components and options for
the powering network
– Procedure to perform the connection to the mains
– Preliminary procedure to set the Control Unit at work
– Maintenance – Help to problem-solving
– Preventive maintenance plan to guarantee the C5G
efficiency over time
– Preventive and special maintenance procedures
– Spare part list
– Wiring diagram

Document preservation
All documents forwarded shall be preserved nearby the Robot System and be at the
disposal of all staff members, who carry out activities on the Robot System. Moreover
the documents shall be preserved in good repair for the entire Robot System operating
life.

Manual content limits

The images in the instruction manuals are aimed at representing the product and may
differ from the items actually installed on the Robot System.

HS-RC-C5E-0_01.fm
7 00/0211
 All manuals and user guides at all-guides.com

Symbols in the manual

Find below the symbols highlighting WARNING, CAUTION and NOTES together with
their meaning

This symbol applies to operating procedures, technical information and

precautions that are to be complied with and/or properly performed to prevent
possible injuries.

This symbol applies to operating procedures, technical information and

precautions that are to be complied with and/or properly performed to prevent
possible equipment damages.

This symbol applies to operating procedures, technical information and

precautions that need necessarily to be highlighted.

This symbol concerns the material disposal procedures ruled by the RAEE
Directive.

This symbol reminds the user to avoid polluting the environment and stimulate a
sustainable attitude, i.e. disposing of the materials in the suitable waste collection
sites.

HS-RC-C5E-0_01.fm
8 00/0211
 All manuals and user guides at all-guides.com

General Safety Precautions

1. GENERAL SAFETY PRECAUTIONS

It deals with a general specification that apply to the whole Robot System. Due to
ist significance, this document is referred to unreservedly in any system
instruction manual.

This specification deals with the following topics:

– Responsibilities
– Safety Precautions.

1.1 Responsibilities
– The system integrator is responsible for ensuring that the Robot System (Robot
and Control System) are installed and handled in accordance with the Safety
Standards in force in the country where the installation takes place. The application
and use of the protection and safety devices necessary, the issuing of declarations
of conformity and any CE markings of the system are the responsibility of the
Integrator.
– COMAU Robotics & Service shall in no way be held liable for any accidents caused
by incorrect or improper use of the Robot System (Robot and Control System), by
tampering with circuits, components or software, or the use of spare parts that are
not included in the spare parts list.

– The application of these Safety Precautions is the responsibility of the persons

assigned to direct / supervise the activities indicated in the Applicability sectionally
are to make sure that the Authorised Personnel is aware of and scrupulously follow
the precautions contained in this document as well as the Safety Standards in
addition to the Safety Standards in force in the country in which it is installed.
– The non-observance of the Safety Standards could cause injuries to the operators
and damage the Robot System (Robot and Control System).

The installation shall be made by qualified installation Personnel and should

conform to all national and local codes.

ge-0-0-0_01.FM
00/0710 9
 All manuals and user guides at all-guides.com

General Safety Precautions

1.2 Safety Precautions

1.2.1 Purpose
These safety precautions are aimed to define the behaviour and rules to be observed
when performing the activities listed in the Applicability section.

1.2.2 Definitions
Robot System (Robot and Control System)
The Robot System is a functional unit consisting of Robot, Control Unit, Programming
terminal and possible options.

Protected Area
The protected area is the zone confined by the safety barriers and to be used for the
installation and operation of the robot

Authorised Personnel
Authorised personnel defines the group of persons who have been trained and assigned
to carry out the activities listed in the Applicability section.

Assigned Personnel
The persons assigned to direct or supervise the activities of the workers referred to in
the paragraph above.

Installation and Putting into Service

The installation is intended as the mechanical, electrical and software integration of the
Robot and Control System in any environment that requires controlled movement of
robot axes, in compliance with the safety requirements of the country where the system
is installed.

Programming Mode
Operating mode under the control of the operator, that excludes automatic operation
and allows the following activities: manual handling of robot axes and programming of
work cycles at low speed, programmed cycle testing at low speed and, when allowed,
at the working speed.

Auto / Remote Automatic Mode

Operating mode in which the robot autonomously executes the programmed cycle at the
work speed, with the operators outside the protected area, with the safety barriers
closed and the safety circuit activated, with local (located outside the protected area) or
remote start/stop.

Maintenance and Repairs

Maintenance and repairs are activities that involve periodical checking and / or
replacement (mechanical, electrical, software) of Robot and Control System parts or
components, and trouble shooting, that terminates when the Robot and Control System
has been reset to its original project functional condition.

ge-0-0-0_01.FM
10 00/0710
 All manuals and user guides at all-guides.com

General Safety Precautions

Putting Out of Service and Dismantling

Putting out of service defines the activities involved in the mechanical and electrical
removal of the Robot and Control System from a production unit or from an environment
in which it was under study.
Dismantling consists of the demolition and dismantling of the components that make up
the Robot and Control System.

Integrator
The integrator is the professional expert responsible for the installation and putting into
service of the Robot and Control System.

m
Incorrect Use
Incorrect use is when the system is used in a manner other than that specified in the
Technical Documentation.

.co
Range of Action
The robot range of action is the enveloping volume of the area occupied by the robot
and its fixtures during movement in space.

1.2.3 Applicability
These Specifications are to be applied when executing the following activities:
es
– Installation and Putting into Service;
– Programming Mode;
– Auto / Remote Automatic Mode;
uid

– Robot axes release;

– Maintenance and Repairs;
– Putting Out of Service and Dismantling
-g
all

ge-0-0-0_01.FM
00/0710 11
 All manuals and user guides at all-guides.com

General Safety Precautions

1.2.4 Operating Modes

Installation and Putting into Service
– Putting into service is only possible when the Robot and Control System has been
correctly and completely installed.
– The system installation and putting into service is exclusively the task of the
authorised personnel.
– The system installation and putting into service is only permitted inside a protected
area of an adequate size to house the robot and the fixtures it is outfitted with,
without passing beyond the safety barriers. It is also necessary to check that under
normal robot movement conditions there is no collision with parts inside the
protected area (structural columns, power supply lines, etc.) or with the barriers. If
necessary, limit the robot working areas with mechanical hard stop (see optional
assemblies).
– Any fixed robot control protections are to be located outside the protected area and
in a point where there is a full view of the robot movements.
– The robot installation area is to be as free as possible from materials that could
impede or limit visibility.
– During installation the robot and the Control Unit are to be handled as described in
the product Technical Documentation; if lifting is necessary, check that the
eye-bolts are fixed securely and use only adequate slings and equipment.
– Secure the robot to the support, with all the bolts and pins foreseen, tightened to
the torque indicated in the product Technical Documentation.
– If present, remove the fastening brackets from the axes and check that the fixing
of the robot fixture is secured correctly.
– Check that the robot guards are correctly secured and that there are no moving or
loose parts. Check that the Control Unit components are intact.
– If applicable, connect the robot pneumatic system to the air distribution line paying
attention to set the system to the specified pressure value: a wrong setting of the
pressure system influences correct robot movement.
– Install filters on the pneumatic system to collect any condensation.
– Install the Control Unit outside the protected area: the Control Unit is not to be used
to form part of the fencing.
– Check that the voltage value of the mains is consistent with that indicated on the
plate of the Control Unit.
– Before electrically connecting the Control Unit, check that the circuit breaker on the
mains is locked in open position.

– Connection between the Control Unit and the three-phase supply mains at the
works, is to be with a four-pole (3 phases + earth) armoured cable dimensioned
appropriately for the power installed on the Control Unit. See the product
Technical Documentation.
– The power supply cable is to enter the Control Unit through the specific fairlead and
be properly clamped.
– Connect the earth conductor (PE) then connect the power conductors to the main
switch.

ge-0-0-0_01.FM
12 00/0710
 All manuals and user guides at all-guides.com

General Safety Precautions

– Connect the power supply cable, first connecting the earth conductor to the circuit
breaker on the mains line, after checking with a tester that the circuit breaker
terminals are not powered. Connect the cable armouring to the earth.
– Connect the signals and power cables between the Control Unit and the robot.
– Connect the robot to earth or to the Control Unit or to a nearby earth socket.
– Check that the Control Unit door (or doors) is/are locked with the key.
– A wrong connection of the connectors could cause permanent damage to the
Control Unit components.
– The C5G Control Unit manages internally the main safety interlocks (gates,
enabling pushbuttons, etc.). Connect the C5G Control Unit safety interlocks to the
line safety circuits, taking care to connect them as required by the Safety
standards. The safety of the interlock signals coming from the transfer line
(emrgency stop, gates safey devices etc) i.e. the realisation of correct and safe
circuits, is the responsibility of the Robot and Control System integrator.

In the cell/line emergency stop circuit the contacts must be included of the control
unit emergency stop buttons, which are on X30. The push buttons are not
interlocked in the emergency stop circuit of the Control Unit.

– The safety of the system cannot be guaranteed if these interlocks are wrongly
executed, incomplete or missing.
– The safety circuit executes a controlled stop (IEC 60204-1 , class 1 stop) for the
safety inputs Auto Stop/ General Stop and Emergency Stop. The controlled stop is
only active in Automatic states; in Programming the power is cut out (power
contactors open) immediately. The procedure for the selection of the controlled
stop time (that can be set on SDM board) is contained in the Installation manual .
– When preparing protection barriers, especially light barriers and access doors,
bear in mind that the robot stop times and distances are according to the stop
category (0 or 1) and the weight of the robot.

Check that the controlled stop time is consistent with the type of Robot connected
to the Control Unit. The stop time is selected using selector switches SW1 and
SW2 on the SDM board.

– Check that the environment and working conditions are within the range specified
in the specific product Technical Documentation.
– The calibration operations are to be carried out with great care, as indicated in the
Technical Documentation of the specific product, and are to be concluded
checking the correct position of the machine.
– To load or update the system software (for example after replacing boards), use
only the original software handed over by COMAU Robotics & Service.
Scrupulously follow the system software uploading procedure described in the
Technical Documentation supplied with the specific product. After uploading,
always make some tests moving the robot at slow speed and remaining outside the
protected area.
– Check that the barriers of the protected area are correctly positioned.

ge-0-0-0_01.FM
00/0710 13
 All manuals and user guides at all-guides.com

General Safety Precautions

Programming Mode
– The robot is only to be programmed by the authorised personnel.
– Before starting to program, the operator must check the Robot System (Robot and
Control System) to make sure that there are no potentially hazardous irregular
conditions, and that there is nobody inside the protected area.
– When possible the programming should be controlled from outside the protected
area.
– Before operating inside the Protected Area, the operator must make sure from
outside that all the necessary protections and safety devices are present and in
working order, and especially that the hand-held programming unit functions
correctly (slow speed, emergency stop, enabling device, etc.).
– During the programming session, only the operator with the hand-held terminal is
allowed inside the Protected Area.
– If the presence of a second operator in the working area is necessary when
checking the program, this person must have an enabling device interlocked with
the safety devices.
– Activation of the motors (Drive On) is always to be controlled from a position
outside the range of the robot, after checking that there is nobody in the area
involved. The Drive On operation is concluded when the relevant machine status
indication is shown.
– When programming, the operator is to keep at a distance from the robot to be able
to avoid any irregular machine movements, and in any case in a position to avoid
the risk of being trapped between the robot and structural parts (columns, barriers,
etc.), or between movable parts of the actual robot.
– When programming, the operator is to avoid remaining in a position where parts of
the robot, pulled by gravity, could execute downward movements, or move
upwards or sideways (when installed on a sloped plane).
– Testing a programmed cycle at working speed with the operator inside the
protected area, in some situations where a close visual check is necessary, is only
to be carried out after a complete test cycle at slow speed has been executed. The
test is to be controlled from a safe distance.
– Special attention is to be paid when programming using the hand-held terminal: in
this situation, although all the hardware and software safety devices are active, the
robot movement depends on the operator.
– During the first running of a new program, the robot may move along a path that is
not the one expected.
– The modification of program steps (such as moving by a step from one point to
another of the flow, wrong recording of a step, modification of the robot position out
of the path that links two steps of the program), could give rise to movements not
envisaged by the operator when testing the program.
– In both cases operate cautiously, always remaining out of the robot’s range of
action and test the cycle at slow speed.

ge-0-0-0_01.FM
14 00/0710
 All manuals and user guides at all-guides.com

General Safety Precautions

Auto / Remote Automatic Mode

– The activation of the automatic operation (AUTO and REMOTE states) is only to
be executed with the Robot System (Robot and Control System) integrated inside
an area with safety barriers properly interlocked, as specified by Safety Standards
currently in force in the Country where the installation takes place.
– Before starting the automatic mode the operator is to check the Robot and Control
System and the protected area to make sure there are no potentially hazardous
irregular conditions.
– The operator can only activate automatic operation after having checked:
• that the Robot and Control System is not in maintenance or being repaired;
• the safety barriers are correctly positioned;
• that there is nobody inside the protected area;
• that the Control Unit doors are closed and locked;
• that the safety devices (emergency stop, safety barrier devices) are
functioning;
– Special attention is to be paid when selecting the automatic-remote mode, where
the line PLC can perform automatic operations to switch on motors and start the
program.

Robot axes release

– In the absence of motive power, the robot axes movement is possible by means of
optional release devices and suitable lifting devices. Such devices only enable the
brake deactivation of each axis. In this case, all the system safety devices
(including the emergency stop and the enable button) are cut out; also the robot
axes can move upwards or downwards because of the force generated by the
balancing system, or the force of gravity.

Before using the manual release devices, it is strongly recommended to sling the
robot, or hook to an overhead travelling crane.

– Enabling the brake releasing device may cause the axes falling due to gravity as
well as possible impacts due to an incorrect restoration, after applying the brake
releasing module. The procedure for the correct usage of the brake releasing
device (both for the integrated one and module one) is to be found in the
maintenance manuals.
– When the motion is enabled again following the interruption of an unfinished
MOVE, the track recovery typical function may generate unpredictable paths that
may imply the risk of impact. This same condition arises at the next automatic cycle
restarting. Avoid moving the Robot to positions that are far away from the ones
provided for the motion restart; alternatively disable the outstanding MOVE
programmes and/or instructions.

Maintenance and Repairs

– When assembled in COMAU Robotics & Service, the robot is supplied with
lubricant that does not contain substances harmful to health, however, in some
cases, repeated and prolonged exposure to the product could cause skin irritation,
or if swallowed, indisposition.
First Aid. Contact with the eyes or the skin: wash the contaminated zones with
abundant water; if the irritation persists, consult a doctor.
If swallowed, do not provoke vomiting or take anything by mouth, see a doctor as
soon as possible.

ge-0-0-0_01.FM
00/0710 15
 All manuals and user guides at all-guides.com

General Safety Precautions

– Maintenance, trouble-shooting and repairs are only to be carried out by authorised

personnel.
– When carrying out maintenance and repairs, the specific warning sign is to be
placed on the control panel of the Control Unit, stating that maintenance is in
progress and it is only to be removed after the operation has been completely
finished - even if it should be temporarily suspended.
– Maintenance operations and replacement of components or the Control Unit are to
be carried out with the main switch in open position and locked with a padlock.

m
– Even if the Control Unit is not powered (main switch open), there may be
interconnected voltages coming from connections to peripheral units or external
power sources (e.g. 24 Vdc inputs/outputs). Cut out external sources when
operating on parts of the system that are involved.

.co
– Removal of panels, protection shields, grids, etc. is only allowed with the main
switch open and padlocked.
– Faulty components are to be replaced with others having the same code, or
equivalent components defined by COMAU Robotics & Service.

After replacement of the SDM module, check on the new module that the setting
of the stop time on selector switches SW1 and SW2 is consistent with the type of
es
Robot connected to the Control Unit.

– Trouble-shooting and maintenance activities are to be executed, when possible,

outside the protected area.
– Trouble-shooting executed on the control is to be carried out, when possible
uid

without power supply.

– Should it be necessary, during trouble-shooting, to intervene with the Control Unit
powered, all the precautions specified by Safety Standards are to be observed
when operating with hazardous voltages present.
– Trouble-shooting on the robot is to be carried out with the power supply cut out
(Drive off).
-g

– At the end of the maintenance and trouble-shooting operations, all deactivated

safety devices are to be reset (panels, protection shields, interlocks, etc.).
– Maintenance, repairs and trouble-shooting operations are to be concluded
checking the correct operation of the Robot System (Robot and Control System)
all

and all the safety devices, executed from outside the protected area.
– When loading the software (for example after replacing electronic boards) the
original software handed over by COMAU Robotics & Service is to be used.
Scrupulously follow the system software loading procedure described in the
specific product Technical Documentation; after loading always run a test cycle to
make sure, remaining outside the protected area
– Disassembly of robot components (motors, balancing cylinders, etc.) may cause
uncontrolled movements of the axes in any direction: before starting a disassembly
procedure, consult the warning plates applied to the robot and the Technical
Documentation supplied.
– It is strictly forbidden to remove the protective covering of the robot springs.

ge-0-0-0_01.FM
16 00/0710
 All manuals and user guides at all-guides.com

General Safety Precautions

Putting Out of Service and Dismantling

– Putting out of service and dismantling the Robot and Control System is only to be
carried out by Authorised Personnel.
– Bring the robot to transport position and fit the axis clamping brackets (where
applicable) consulting the plate applied on the robot and the robot Technical
Documentation.
– Before stating to put out of service, the mains voltage to the Control Unit must be
cut out (switch off the circuit breaker on the mains distribution line and lock it in
open position).
– After using the specific instrument to check there is no voltage on the terminals,
disconnect the power supply cable from the circuit breaker on the distribution line,
first disconnecting the power conductors, then the earth. Disconnect the power
supply cable from the Control Unit and remove it.
– First disconnect the connection cables between the robot and the Control Unit,
then the earth cable.
– If present, disconnect the robot pneumatic system from the air distribution line.
– Check that the robot is properly balanced and if necessary sling it correctly, then
remove the robot securing bolts from the support.
– Remove the robot and the Control Unit from the work area, applying the rules
indicated in the products Technical Documentation; if lifting is necessary, check the
correct fastening of the eye-bolts and use appropriate slings and equipment only.
– Before starting dismantling operations (disassembly, demolition and disposal) of
the Robot and Control System components, contact COMAU Robotics & Service,
or one of its branches, who will indicate, according to the type of robot and Control
Unit, the operating methods in accordance with safety principles and safeguarding
the environment.
– The waste disposal operations are to be carried out complying with the legislation
of the country where the Robot and Control System is installed.

ge-0-0-0_01.FM
00/0710 17
 All manuals and user guides at all-guides.com

General Safety Precautions

1.2.5 Performance
The performances below shall be considered before installing the robot system:
– Stop distances
– Mission time (typ. case).

Stop distances
– With Robot in programming modality (T1), if you press the sttop pushbutton (red
mushroom-shaped one on WiTP) in category 0 (secondo norma EN60204-1), you
will obtain:

Tab. 1.1 - Stop spaces in programming modality (T1)

Expected Stopping Stopping
Mode Case
speed time space
Nominal 120 ms 30 mm
T1 250 mm/s
Limit 500 ms 125 mm

Tab. 1.2 - Safety electronics reaction time in programming

modality (T1)
Expected Stopping
Mode Case
speed time
For the safety inputs of the SDM module (e.g.
stop pushbutton of TP in wired version)
For the stop stop and enabling device inputs 150 ms
from the TP in wireless version, when the
T1 250 mm/s
safety wire trasmission is active.
For the time-out of stop input and enabling
device from TP in wireless version, when the 350 ms
safety wire transmission is lost or interrupted.

– Considering the Robot in automatico modality, under full extension, full load and
maximmum speed conditions, if you press the stop pushbutton (red
mushroom-shaped one on WiTP) in category 1 (according to norm EN60204-1)
you will trigger the Robot complete stop with controlled deleration ramp.
Example: for Robot NJ 370-2.7 you will obtain the complete stop in about 85 °
motion, that correspond to about 3000 mm movement measured on TCP flange.
Under the said conditions, the stopping time for Robot NJ 370-2.7 is equal to 1,5
seconds.

Mission time (typ. case)

– We remind you that the safety system efficiency covering is equal to 20 years
(mission time of safety-related parts of control systems (SRP/CS), according to
EN ISO 13849-1).

ge-0-0-0_01.FM
18 00/0710
 All manuals and user guides at all-guides.com

Maintenance prescriptions

2. MAINTENANCE PRESCRIPTIONS
This chapter deals with the following topics:
– Precautions before starting
– Precautions while carrying out maintenance activities
– Precautions at the end of the maintenance activities
– Maintenance staff
– Equipment and tools necessary
– Torque wrench settings.

The maintenance activities that not are expressly specified in this manual are not
allowed. If necessary, turn to the manufacturer.

2.1 Precautions before starting

– The majority of maintenance activities on the Control Unit are to be carried out wih
power off. In those cases the wording “Main switch open (OFF)” is specified in the
maintenance sheet.
When the main switch is OFF, the X120 terminal board and the related cable up
the main switch are energized. In that case, the procedure to cut the power off
completely requires the power disconnection from the mains.
– The maintenance activities to be carried out on the cabinet main powering section
shall be perfomed only after disconnecting the power from the mains. In those
cases the wording “Incoming voltage off” is specified in the maintenance sheet.
– Use orignal spare parts only. Spare parts are supplied by Comau. The bill of spare
parts is to be found in Chap.9. - Spare parts on page 91.

2.2 Precautions while carrying out maintenance

activities
– If the fault type allows the robot re-positioning, we recommed to move it in resting
position, before carrying out any maintenance activity.
– We remind you that in virtue of the Control Unit safety circuits inherent features, a
warranty reduction may be possible in case of multiple faults (refer to norm EN ISO
13849-1).

In case of maintenance and/or troubleshooting activities on the safety

circuits, do not stand nearby the Robot and carry out the motion in jog
mode keeping at suitable distance.

HS-RC-C5E-MAN_01.fm
00/0309 19
 All manuals and user guides at all-guides.com

Maintenance prescriptions

2.3 Precautions at the end of the maintenance

activities
– After completing the maitenance activities, check whether the Control Unit and
matched Robot operate properly. Have the robot performing some working cycle
and check the safety device functionality before leaving the station.

At the end of each maintenance session, the first machine start-up shall
be regarded as a test for the whole plant. During such phase the operator
shall stand outside the Robot range of action but in an position that
allows to check its movements. Moreover, he/she shall have the
Progrmaming Terminal at disposal nearby.

2.4 Maintenance staff

The maintenance staff shall be suitably trained, in order to be able to use the lifting
means properly (in case the whole Control Unit is to be replaced).
Moreover, the staff shall be warned or trained (in electrics) and therefore aware of the
risks associated with electric energy and of the measures to be taken to safely reach the
Control Unit modules.

2.5 Equipment and tools necessary

The components fastening items (screws, nuts) have been standardized as much as
possible.
The minimum equipment necessary to carry out maintenance activities on the C5G
Control Unit is divided according to the maintenance typology:
– as for preventive maintenance refer to par. 7.2 Equipment and tools required on
page 43.
– as for special maintenance refer to par. 8.2 Equipment and tools required on
page 56.

2.6 Torque wrench settings

While disassembling and re-assembling the components comply with the screw torque
wrench settings. If not otherwise specified, apply the torque corresponding to the screw
typology.

Do not overtight, as you may damage the thread and therefore the item position
in its seat.
Do not under tight, as it may cause the item falling and/or overheating (and
consequent breaking) due to an incorrect adherence to the dissipating frame.

HS-RC-C5E-MAN_01.fm
20 00/0309
 All manuals and user guides at all-guides.com

Help in Trouble Shooting

3. HELP IN TROUBLE SHOOTING

This chapter deals with the following topics:
– Precautions before starting
– Methodology
– Comau Customer Center

m
3.1 Precautions before starting
– Read carefully the instructions in Chap.2. - Maintenance prescriptions on page 19

3.2 Methodology
–
–
.co
Problem analysis
Diagnosis messages
es
– Identification items and abbreviations for connectors, cables and modules
– Traceability for replacement purposes
– Replacing the components
uid

3.2.1 Problem analysis

The C5G Control Unit delivers information about the system status using:
– LEDs, located on the modules and cards
– diagnosis messages, displayed through he programming terminal.
Depending on the plant condition, one or both means (LEDs, messages) may be useful
-g

to detect possible faults:

– during the boot phase, the programming terminal is not active and it is necessary
to rely on the LEDs on the modules
– when the programming terminal is active, the Diagnosis messages delivered are
all

more efficient
– in all cases, in particular for the auxiliary circuit power supplies, LEDs represent the
most immediate diagnostic procedure
– the pins in the tables in Chap. Details about the C5G Control Unit on page 43 of
the “Technical specifications” manual allow to check the availability of the expected
corresponding signal
– for the connection among modules and further information about the circuits, refer
to the Control Unit Circuit Diagram (ver. ACC1 and ACC3).

HS-RC-C5E-MAN_02.fm
00/0111 21
 All manuals and user guides at all-guides.com

Help in Trouble Shooting

3.2.2 Diagnosis messages

The diagnosis messages are coded using numerical codes matched to a short
description and are displayed through the programming terminal.
To better understand the message, identify the cause that led to it as well as the suitable
method to remove it, use the WinC4G software.
The software main window (Fig. 3.1) displays the above mentioned information. To call
the information enter the error code in field (A).

Fig. 3.1 - WinC4G main window related to the error codes

3.2.2.1 Meaning of the format

The error messages are displayed on the programming terminal and WinC4G software
and also stored in a file named ERROR.LOG. It deals with a Control Unit memory
resident file that can be recalled if a message is erased or the user wishes to check
which alarms occurred.
The message format is the following:

xxxx.yyyyy-zz : Text

Tab. 3.1 - Message format

Position Description
Stored event progressive number.
xxxx
The messages identified by ---- are not stored.
yyyyy Error code
zz Seriousness level (see details in Tab. 3.2)
Text Message text

ex. ----.28808-10 : Gate safety

The error message meaning is the following:

HS-RC-C5E-MAN_02.fm
22 00/0111
 All manuals and user guides at all-guides.com

Help in Trouble Shooting

– ----- (the message is not stored)

– 28808 (error numerical code)
– 10 (seriousness level)
– Gate safety (message text featuring the fault detected on the plant).

3.2.2.2 Alarm quitting

Find below the quitting procedures as a function of the alarm seriousness level:

Tab. 3.2 - Seriousness level and corresponding quitting

procedure
Seriousne
Meaning Impact on the system Quitting procedure
ss level
00 Informative message None None
01 Informative message None None
02 Warning No impact on the Control Unit None
status.
03 Not used
04 PDL2 programme error Programme in PAUSE or – Quit the fault pressing the RESET
HOLD mode, if it deals with a (Ctrl + HOME keys on WinC4G)
holdable programme. key
– Remove the fault in the
programme.
– Restart the programme.
05 Not used
06 PDL2 programme error All programmes in PAUSE or – Quit the fault pressing the RESET
HOLD mode, if it deals with (Ctrl + HOME keys on WinC4G)
holdable programmes. key
– Remove the fault in the
programme.
– Restart all programmes.
07 Not used
08 Hold HOLD – Quit the fault pressing the RESET
(Ctrl + HOME keys on WinC4G)
key
– Remove the cause that gave rise to
the alarm
– Restore the programme pressing
the START key
09 Not used
10 Driving devices off HOLD and following DRIVE – Quit the fault pressing the RESET
OFF (Ctrl + HOME keys on WinC4G)
key
(stop according to category 1, – Remove the cause that gave rise to
in compliance with norm EN the alarm
60204-1)
– DRIVE ON
– Restore the programme pressing
the START key

HS-RC-C5E-MAN_02.fm
00/0111 23
 All manuals and user guides at all-guides.com

Help in Trouble Shooting

Tab. 3.2 - Seriousness level and corresponding quitting

procedure (Continued)
Seriousne
Meaning Impact on the system Quitting procedure
ss level
11 Driving devices off DRIVE OFF – Quit the fault pressing the RESET
(Ctrl + HOME keys on WinC4G)
(stop according to category 0, key
in compliance with norm EN – Remove the cause that gave rise to
60204-1) the alarm
– DRIVE ON
– Restore the programme pressing
the START key
12 Driving devices off HOLD, DRIVE OFF and – Quit the fault pressing the RESET
DEACTIVATE (Ctrl + HOME keys on WinC4G)
key
(stop according to category 1, – Remove the cause that gave rise to
in compliance with norm EN the alarm
60204-1 and programme
– DRIVE ON
deactivation)
– Restore the programme pressing
the START key
13 Fatal error Stops the Robot according to – Remove the cause that gave rise to
category 0 (in compliance with the alarm
norm EN 60204-1) and – Switch the Control Unit off and
deactivate all PDL2 programs allow at least 30 seconds for the
(DEACTIVATE) and leaves UPS module deactivation
the system in minimum
– Switch the Control Unit back on
configuration.
14 Fatal error Stops the Robot according to – Remove the cause that gave rise to
category 0 (in compliance with the alarm
norm EN 60204-1) and – Switch the Control Unit off and
deactivate all PDL2 programs allow at least 30 seconds for the
(DEACTIVATE) and leaves UPS module deactivation
the system in minimum – Switch the Control Unit back on
configuration.
15 Fatal error Stops the Robot according to – Remove the cause that gave rise to
category 0 (in compliance with the alarm
norm EN 60204-1) and – Switch the Control Unit off and
deactivate all PDL2 programs allow at least 30 seconds for the
(DEACTIVATE) and leaves UPS module deactivation
the system in minimum – Switch the Control Unit back on.
configuration.

HS-RC-C5E-MAN_02.fm
24 00/0111
 All manuals and user guides at all-guides.com

Help in Trouble Shooting

3.2.3 Identification items and abbreviations for connectors,

cables and modules
All connectors and cables in the Control Unit are supplied with clear abbreviations and
characterized univocally, to allow a rapid identification of the connection as well as the
Traceability for replacement purposes (see par. 3.2.4 on page 25).
The abbreviations are posted both on the movable and the fixed connector. In the case
of the latter, the abbreviation is silk-screen-printed nearby the component.

Fig. 3.2 - Example of abbreviation on connector and cable

Each connector ending on the modules is identified by the letter “X” followed by a
progressive number and the abbreviation of the corresponding component (example X9
/ CPU, X100 / FIA, etc.).
The connector abbreviation is clearly silk-screen-printed on the component.

Fig. 3.3 - Example of abbreviation on connector

3.2.4 Traceability for replacement purposes

Each cable / component is identified by a label featuring the Serial Number S/N and the
purchase code, Part Number, P/N.
The codes are defined as follows:
– S/N followed by 4 figures (year and month of manufacturing) e 2 letters
– P/N followed by 8 figures (purchase code), a separating dot and 2 figures
identifying the review status.

HS-RC-C5E-MAN_02.fm
00/0111 25
 All manuals and user guides at all-guides.com

Help in Trouble Shooting

3.2.5 Replacing the components

To replace the components, we recommend to identify the damaged ones through the
Identification items and abbreviations for connectors, cables and modules, such as to
be able to replace them with an identical spare part.
Find in Chap.9. - Spare parts on page 91 the codes and descriptions of the components
available as spare parts.
The spare parts can be purchased directly from Comau at the addresses listed in
par. 3.4 Comau Customer Center on page 29 where it is also possible to have the

m
damaged components repaired.

Do not carry out independent or unauthorized repairing activities on the damaged

modules. The repairing activities shall be carried out by Comau only.

3.3 Control Unit outline diagrams

.co
In the follwing pages are shonw the outline wiring diagrams of the system main
interconnctions Nelle pagine seguenti sono riporta.
es
For all necessary connection information and details, refer to the Control Unit and
Robot wiring diagrams .
uid
-g
all

HS-RC-C5E-MAN_02.fm
26 00/0111
 LINE
400V~ to 500V~ PE OPD USB
R S T h 123
X120 Ext. FAN Int. FAN

00/0111
CR17.2300.60xx E114 E113 E112 E111 E110
USB CR17.1307.80xx

CR17.2305.60xx 24V ESM Supply & 24V Supply Distribution Command

CR17.2306.60xx 24V Supply Distribution

Q100

CR17.2311.61xx Enables Axis 1-6

CR17.2301.60xx Ballast
CAN Bus Internal

Encoder Axis 1-6

HS-RC-C5E-MAN_02.fm
X1 CR17.2315.60xx

X4 X3 X108 X109 X100 X101 X107 JP200

CR17.2304.61xx
X10
ETH PowerLink
LINE
FILTER DC bus

CR17.2315.60xx
ready
X2
Z1 4 3 2 1 X3A X3A X1 X1 X2 X3 X3A X2 X1 X11 X3A X2 X1 X11 X3A X2 X1 X11
USB X3B X3B X11 X3B X11 X3B X11
ERM-1 ERM-2
APC PPS ASM IAM1 IAM2 IAM3 Dup. Line E-Stop A-Stop da Linea
Drive ON. Dup. En. Device
Inverter Inverter Inverter Progr. Status Autom. Status
Acopos Passive Aux.. SDM X310
Axis Axis Axis
PC Power Supply
Module 1 Module 2 Module 3 Safety & Distribution Module X311

CR17.2302.60xx
Supply Module

X5B
X5B
X5B

X5A
X5A
X5A
CR17.2413.80xx
X312

X4A
X4B
X4A
X4B
X4A
X4B
X1

X5A
COM ETH

X5B
2 1 2 1 CAN
X106

Brake
A
Power Supply Line

Fases Motor
CR17.2303.60xx X103 B

C
CR17.2314.61xx CAN Bus Internal X119 X112 X110 X104 X124 X126 X128 X102 X122 X302

2 1
TP E-Stop, En.Dev., 24V Supply.
PLUG PLUG PLUG
CR17.2315.61xx
TP Ethernet
CR17.2316.61xx
CR17.2317.61xx

ETH PowerLink

CR17.2307.61xx
All manuals and user guides at all-guides.com

PFG
X3A X3B X3C
Powerlink X2

CR17.2312.61xx
UPS Fieldbus
CR17.2309.61xx
Gateway
CR17.2310.60xx

X1

CR17.2308.6xxx
+24V DriveOFF

Internal main connections

CIP
X124 X60 CONNECTOR X10 CONN. X30 CONN.

1 WIRING WITH WIRED TP

Docking Wired TP 2 WIRING WITH DOCKING STATION WIRELESS

Station

400 Vac, 24 Vdc Power supply distribution

Help in Trouble Shooting

27
 All manuals and user guides at all-guides.com

Help in Trouble Shooting

Vd c

SDM MODULE
X30 X102 X103
1A
24V INTP 24V INT. 1 A
1
2
8
24V EXT. 1 B
29
FIELD BUS 2

24V EXT. 1 C
15
0V 2
22

0V
INT./EXT.
2

9
X106
24V I/O 1
16
2
23
0V 3
30
24V SAFE 4

X122
X124
24V SAFE
1

0V
2

24V I/O
3

JP200 24V EXT. FIELD BUS

4

10

X126
24V EXT. 8A DRIVE ON
24V SAFE
1

24V INT. 7

SL2 P8A PSF 0V

2

24V I/O
3
X100
5A 9
24V
ASM PIO 24V EXT. FIELD BUS
4
AUX. 10
SUPPLY SL1 P5A
MODULE 0V
X128
5A 24V SAFE
1

1A 5A 0V
2

24V I/O
3
DRIVE OFF
9

24V EXT. FIELD BUS

24V DRIVE OFF

4
24V ROBOT

10
24V FANS

24V INT.
0V

0V

0V

0V

X119 X110
X2 X1
78 79 43 42

INT./EXT. FANS
A B

12 36 10d 11d

X10 X60 X124

24V ROBOT SUPPLY

iTP

24 Vdc Power supply

distribution
ROBOT BRAKES RELEASER

HS-RC-C5E-MAN_02.fm
28 00/0111
 All manuals and user guides at all-guides.com

Help in Trouble Shooting

3.4 Comau Customer Center

The Comau Customer Centre will be at your disposal at the following addresses:

Section Address Service available

To get help for troubleshooting and request
Cause and solution [email protected]
software options
Spare parts [email protected] To request spare parts
To request intervention for repairing
Repair [email protected]
activities

Alternatively, please turn to the manufacturer following the instructions in par. 2.5.4
Manufacturer’s details on page 24 of the “Technical specifications ” manual.

HS-RC-C5E-MAN_02.fm
00/0111 29
 All manuals and user guides at all-guides.com

Switching off the power supply

4. SWITCHING OFF THE POWER SUPPLY

This section deals with the following topics:
– Precautions and risks associated to the power supply off-switching
– Switching off the power supply.

4.1 Precautions and risks associated to the

power supply off-switching
– After switching off the Control Unit wait for at least 30 seconds before switching
it back on.
– Before removing any connector wait for at least 30 seconds and make sure that
all LEDs are off.
Failure to comply with those warnings may result in :
• in the jamming of one or more modules
• in the damaging of one or more modules functionality.
– In case one or more module stop, switch off the system and wait for at least 30
seconds before switching the power supply back on.
– If installed, connector X120 shall not be used for the power supply sectioning
(C5G-MCK option).
– To increase the battery life do not switch off the Control Unit before carrying out
the software shutdown.
– The software shutdown procedure enables the files and applications closing
without requiring the buffer buttery.

If the Control Unit is switched off when the Robot is in motion, the system and
therefore the Robot are compelled to perform an immediate stop without
deceleration ramps with consequent stress for the kinematic chain, drift of the
trajectory direction (unpredictable also due to the force of gravity) and risk of
impacts. If this stop modality is performed repeatedly, the Robot System and/or
equipment connected to the Robot may suffer damages.

HS-RC-C5E-MAN_09.fm
30 00/0211
 All manuals and user guides at all-guides.com

Switching off the power supply

4.2 Switching off the power supply

Status: – Unimportant
RPU

Material: – Padlock diameter

min. 5 mm / max 8 mm
OPM

(min. 0.19 in / max 0.31 in),

(not supplied)
Equipment: – Not required

m
.co
Preliminary procedures / notes
es
– Tha majority of maintenance activities for the Control Unit are to be carried out
with power supply off. In those cases the maintenance card feature the wording
“Main switch open (OFF)”.
– Some activities, especially those related to the box main power supply section,
are to be carried out only after switching off the mains power supply. In those
uid

caes the maintenance card features the wording “Incoming power supply off”.

Operating procedure
Main switch control in OFF position
-g
all

Main switch open (OFF)

a. Carry out the software shutdown. Act on the specific control on the programming
terminal.

b. Wait for the shutdown procedure to end.

c. Padlock and post the plate specifying “Maintenance in progress”.

d. With box door closed, move lever (A) of the Q100 main switch to 0 (OFF)
position.

HS-RC-C5E-MAN_09.fm
00/0211 31
 All manuals and user guides at all-guides.com

Switching off the power supply

Operating procedure (Continua)

e. Press lever (B) to access the slot.

f. Fit the padlock in the slot available on the switch control.

g. Remove the padlock only after completing the maintenance activities.

h. The padlock is not supplied together with the electric box.

With main switch open, the connector X120 and the cable up the main
switch are energized.

HS-RC-C5E-MAN_09.fm
32 00/0211
 All manuals and user guides at all-guides.com

Switching off the power supply

Operating procedure (Continua)

Incoming voltage off
(if the optional connector X120 is not installed)

a. Perform the power supply off-switching as specified in Main switch open (OFF).

b. Open and padlock the main switch up the Control Unit. The padlock is not
supplied together with the Control Unit.
Incoming voltage off
(if the optional connector X120 is installed)
If available, connector X120 shall not be removed with Q100 main
switch closed.

a. Perfrom the power supply

off-switching as specified in the
previous steps.

b. This activity requires the

removel of connector X120 (C),
located in the box lower area.

c. Release the levers (D).

d. Remove the movable X120

connector (C).

Folow-up procedure
– Not required.
– When closing the door after completing the maintenance activities:
• do not damage the control and extension shaft
• close the doors with care, avoiding excessive pressure.
• secure the door acting on the lock.

HS-RC-C5E-MAN_09.fm
00/0211 33
 All manuals and user guides at all-guides.com

How to reach the modules

5. HOW TO REACH THE MODULES

This chapter deals with the following topics:
– Precautions before starting
– Risks associated with the module reaching procedures
– Module location and reaching methods

5.1 Precautions before starting

– Read carefully the instructions in Chap.2. - Maintenance prescriptions on page 19
– Reach for the internal modules only after disconnecting the power.

5.2 Risks associated with the module reaching

procedures
– Reaching the modules from the rear door does not endanger the operator. The
protection category for the internal electric components is IP2x.
– Reaching the modules after removing the rear panel, implies the following
risks:
• burn, due to the high temperature of the recovery resistance and the CPU,
power supplies and power modules dissipator rear panel
• cut / abrasion, due to rotating fans, (only if the powering has not been turned
off as required).

5.3 Module location and reaching methods

The modules can be reached through:
– Front door
– Upper panel
– Rear panel.
Find in Tab. 5.1 (in alphabetical order) the modules and components that are included
in the maintenance plan and the related access point.

Tab. 5.1 - Module / component list and access point

Module / componente Access point

ACE - Arm Controller Electromechanical

Upper panel
(ACE)

HS-RC-C5E-MAN_03.fm
34 00/0309
 All manuals and user guides at all-guides.com

How to reach the modules

Tab. 5.1 - Module / component list and access point (Continued)

Module / componente Access point

ACC - CPU, power supplies and power Front door (see par. 5.3.1 on
modules page 36)

Front door (see par. 5.3.1 on

CIP - Connector Interface Panel (CIP)
page 36)

Rear panel (see par. 5.3.3 on

page 38) and
ERR - Energy Recovery Resistance
Upper panel (see par. 5.3.2 on
page 37)

Upper panel (see par. 5.3.2 on

FAN - Internal ventilation system - E110
page 37)

Rear panel (see par. 5.3.3 on

FAN - Internal ventilation system - E111..E114
page 38)

Front door (see par. 5.3.1 on

OPD - Operator Panel Devices (OPD)
page 36)

Front door (see par. 5.3.1 on

SDM - Safety Distribution Module (SDM)
page 36)

Front door (see par. 5.3.1 on

UPS - Uninterruptible Power Supply (UPS)
page 36)

HS-RC-C5E-MAN_03.fm
00/0309 35
 All manuals and user guides at all-guides.com

How to reach the modules

5.3.1 Front door

Equipment
Supplied fist key
1 Fastening screws
Not required

m
Be careful
– Terminals are in
protection
category IP2x
3

.co
2 Precautions
– if possible, turn the power off
before starting to work inside
the cabinet.
es
uid

Front door opening procedure

a. Turn the supplied key by 90° clockwise (1).

b. Open the door (2)

c. The door is supplied with a special item that locks it in open position (3).
-g

Front door closing procedure

a. Make sure the lock inside lever is vertical and pointing upwards.
all

b. Unlock the door acting on the lower locking item (3).

c. Close the door.

d. Lock the door using the supplied key, turning it by 90° anticlockwise.

e. Do not leave the key in the lock.

HS-RC-C5E-MAN_03.fm
36 00/0309
 All manuals and user guides at all-guides.com

How to reach the modules

5.3.2 Upper panel

Equipment
Allen spanner 3 mm
Fastening screws
1
TSEI M5 no. 2

Be careful
– Terminals are in
protection
category IP2x

– The X120 terminal board is

2 energized also when the main
switch is off
3
Precautions
– Always disconnect the power
from the mains before reaching
the upper panel.
– Disconnect and padlock at the
power source.

Cabinet upper panel opening procedure

a. Unscrew the 2 TSEI screws and the 4 eyebolts located on the panel (1).

b. Lift and move the panel (2) slightly away; be very careful to the earth connection
on the panel (3).

c. Disconnect the earth wire (3) from the movable panel side.

Cabinet upper panel closing procedure

a. Connect the earth wire (3).

b. Lay the panel and tighten the 2 TBEI screws without applying an excessive
torque.

c. Tighten the 4 eyebolts, making sure the 4 O-Rings in teflon are present.

HS-RC-C5E-MAN_03.fm
00/0309 37
 All manuals and user guides at all-guides.com

How to reach the modules

5.3.3 Rear panel

Equipment
Allen spanner 3 mm
1 Fastening screws
TCEI M4 no. 2

Be careful
– Rotating fan
– Hot surfaces

2 3 4 Precautions
– Always disconnect the power
before reaching the rear panel.
– Be careful to hot surfaces:
recovery resistance and
dissipator.

x3

Cabinet rear panel opening procedure

a. Unscrew the 2 TCEI screws located on the panel (1) top.

b. Remove the panel (2) and lift it (3) to release it from the 3 lower pins.

Cabinet rear panel closing procedure

a. Place the panel on the cabinet lower part and have the 3 pins fitting together with
the holes in the panel (4) base.

b. Bring the panel near the cabinet.

c. Tighten the 2 TCEI screws without applying an excessive torque.

HS-RC-C5E-MAN_03.fm
38 00/0309
 All manuals and user guides at all-guides.com

How to move the robot when the control unit is damaged

6. HOW TO MOVE THE ROBOT WHEN THE

CONTROL UNIT IS DAMAGED
This chapter deals with the following topics:
– Precautions before starting
– Risks associated with the Robot handling with Control Unit disconnected
– How to use the Brake Release module C5G-OBR

6.1 Precautions before starting

– Read carefully the instructions in Chap.2. - Maintenance prescriptions on page 19
– The “integrated brake releasing device” located on the Robot may be disabled if
the Control Unit is damaged. In that case, it is possible to use the brake releasing
Module C5G-OBR (optional). The brake release Module C5G-OBR is to be
regarded as an alternative solution in case the programming terminal cannot be
used.
– The brake releasing Module C5G-OBR powers the engine brakes with a 24Vdc
current from an outside source. This command may therefore give rise to possible
dropping risks (refer to par. 6.2 Risks associated with the Robot handling with
Control Unit disconnected on page 39).
– The “integrated brake releasing device” usage procedures are to be found in each
specific Robot maintenance manual.

6.2 Risks associated with the Robot handling

with Control Unit disconnected
– The axes releasing procedure may result in the axes dropping.
– The brake release module C5G-OBR cuts off all system safety devices:
emergency stop, enabling device push button, general stop and fence.
– Depending on the load applied to the Robot wrist and position, the axes may move
unpredictably and induce a dropping path that is not perpendicular to the floor.
– While carrying out those activities, the operators shall never stand in the operating
area and in particular under the Robot axes.
– Suitable lifting means may be required to lift the axes and equipment installed on
the Robot wrist, due to their weight (e.g. crane, bridge crane).
– In case of person trapping, enable the brake releasing control only if you are sure
that the involved person will not have to experience a pressure increase caused by
the released axes weight.

HS-RC-C5E-MAN_08.fm
00/0511 39
 All manuals and user guides at all-guides.com

How to move the robot when the control unit is damaged

6.3 How to use the Brake Release module

C5G-OBR

Status: – Power off

Material: – Powering cable supplied with plug
suitable for the power connection
source (not included in the brake
releasing device module option
C5G-OBR)
Equipment: – Brake releasing module C5G-OBR
– Suitable lifting means to support the
Robot axes subject to gravity

Typical Robot figure

Preliminary procedures / notes

The axes releasing procedure may result in the axes dropping due to
gravity. Please refer to par. 6.2 Risks associated with the Robot
handling with Control Unit disconnected on page 39.
–The brake release Module C5G-OBR option includes a movable plug
suitable for the panel socket located on the module rear side. Before the first
usage, prepare a powering cable with plug suitable for the power supply source
available in the operating area.
– Power the module (from 100 to 230 Vac, 1.5 A @ 120 Vac / 0.7 A @ 230 Vac).
The cable section shall be at least 0.5 mm² / 20 AWG. Adjust the section
according to the cable length and guard up the system.
Make sure the powering network voltage is suitable for the brake
releasing device.

Operating procedure
a. Support the robot axes subject to gravity by means of a crane or bridge crane.
Use ropes or bands, but do not use chains. Refer to the Robot manual to identify
the most suitable point to sling the Robot.
b. To release the Robot axes:
• Disconnect the power connector X2 by the Robot base. The connector
position is different depending on the Robot type (if necessary, refer to the
Robot manual).

HS-RC-C5E-MAN_08.fm
40 00/0511
 All manuals and user guides at all-guides.com

How to move the robot when the control unit is damaged

Operating procedure (Continued)

• Connect the movable
connector (A) to the
connector X2 by the Robot
base. The movable
connector (B) is not to be
used and can be left on the
floor.

m
.co
c. To release axes from 7 to 10:
• Disconnect the power connector from the involved axis. The connector
position is different depending on the installation type.
• Connect the movable
connector (B) to the
connector of the
corresponding axis to be
es
released. The movable
connector (A) is not to be
used and can be left on the
floor.
uid

d. Supply input power (C) to the

releasing module.

e. The powering is signalled

-g

through the green LED (D)

lighting up.
all

Illustrative picture

HS-RC-C5E-MAN_08.fm
00/0511 41
 All manuals and user guides at all-guides.com

How to move the robot when the control unit is damaged

Operating procedure (Continued)

f. Select the axis to be released on the selector switch (E).

g. Keep tight the ropes that are used the support the axes subject to gravity.
h. To release Robot axes 1 to 6:
• Axes from 1 to 6 can be
selected singularly
together with the related
position.

i. To release axes from 7 to 10:

• Axes from 7 to 10 are
connected through a
dedicated connector, that
can be connected to one
axis at a time and
activated only with
selector switch in position
“7-8-9-10”.
j. Use the lever push button (F) to release the involved axis. Operate the push
button by pressing shortly and check the movement produced by the released
axis. At the same time, release gradually the rope used to support the axes
subject to gravity.

k. The motion stops when the push button is released, as the brake is applied
(control enabled by the user action).

Follow-up procedure
– Restore the power connector connections on the Robot and /or involved axes.

Restoring the Robot functionality after using the releasing device

If after using the releasing device the robot is still operating, the automatic cycle shall
not to be restarted, as the path recovery typical functionality may create
unpredictable paths.
To prevent possible impacts due to the path recovery performing at the interrupted
move point, act as follows:

a. disable the programmes and/or outstanding move instructions

b. have the robot moving to home (or out-of-range) position, acting on the
programming terminal

c. restart the programme and carry out some cycles at reduced speed to check the
robot behaviour.

HS-RC-C5E-MAN_08.fm
42 00/0511
 All manuals and user guides at all-guides.com

Preventive maintenance

7. PREVENTIVE MAINTENANCE
This chapter deals with the following topics:
– Precautions before starting
– Equipment and tools required
– Preventive maintenance plan

7.1 Precautions before starting

– Read carefully the instructions in Chap.2. - Maintenance prescriptions on page 19
– To guarantee the Control Unit proper operating, it is necessary to carry out
preventive maintenance activities periodically, to reduce the amount of faults
caused by the ordinary deterioration over time and preserve its functional features
longer.

In case of poor or missing preventive maintenance activities during the warranty

period, this will be regarded as prejudicial to the warranty itself.

7.2 Equipment and tools required

The minimum equipment to carry out preventive maintenance activities on the C5G
Control Unit is:

Tab. 7.1 - Equipment and tools required

Vacuum-cleaner
Soft bristle brush
Crossheaded and bladeheaded screwdrivers set
Allen spanner set (sizes in mm)
Ecological solvent
Cases
Gloves

HS-RC-C5E-MAN_04.fm
00/0309 43
 All manuals and user guides at all-guides.com

Preventive maintenance

7.3 Preventive maintenance plan

Find in Tab. 7.2 the preventive maintenance plan based on the frequency.
The maintenance sheets are ordered by abbreviation and listed in alphabetical order.

Tab. 7.2 - Preventive maintenance plan

Frequency Activity / Sheet Ref. ¹
When carrying out other ACC: door closing and seal efficiency check (see par. 7.4 on P1
activities page 45)
Check the efficiency of the system of signs
Depending on the installation ACO: emptying the condensate collectiong can
environment
8 months E111..E114: fan cleaning (see par. 7.8 on page 51)
8 months Check the safety circuits and devices.
Check the functionality of the following devices at least every 8
months:
– emergency push button, checking the actual functionality of
the two channels
– enabling push button (enabling device) checking the actual
functionality of the two channels. The C5G diagnosis system
checks the efficiency of the related safety circuit and, in case of
fault, displays a corresponding message on the programming
terminal.
– inputs of the emergency stop, Auto Stop (Gates) and
General Stop checking the actual functionality of the two
channels. The C5G diagnosis system checks the efficiency of
the related safety circuits and, in case of fault, displays a
corresponding message on the programming terminal.
– Pilz safety relay available for the C5G-IEAK option (if
installed).
Please, refer also to the manual related to the cell
where the C5G will be installed.

8 months ACO: cleaning the condenser (if installed).

16 month E110: fan cleaning (see par. 7.7 on page 49)
3 years (2 years *¹) UPS: replacing the battery (see par. 7.9 on page 53)

*¹ We recommend the battery preventive replacement in case the

installation area is subject to repeated power supply interruptions or
stops without performing the software shutdown procedure. This
advanced replacement guarantees optimum performances in any
situation.

HS-RC-C5E-MAN_04.fm
44 00/0309
 All manuals and user guides at all-guides.com

Preventive maintenance - ACC

7.4 ACC: door closing and seal efficiency check

Arm Controller Cabinet

Status: – Irrelevant
Material: – Not required
Equipment: – Not required

Front view

Preliminary procedures / notes

– The cabinet door shall remain closed to guarantee the efficiency of the cooling
system and prevent contamination from entering in the cabinet. Thanks to the
structure, the IP 54 procetction category of the cabinet guarantees such
efficiency level.
– The deterioration of the seal performances may have a detrimental impact on this
situation.

Operating procedure
a. Check the seals efficiency and the correct positioning in their seat along the
entire door perimeter.

b. If necessary, replace the seals.

Follow-up procedure
– Not required

HS-RC-C5E-ACC_01.fm
45 00/0309
 All manuals and user guides at all-guides.com

Preventive Maintenance - ACO

7.5 ACO: cleaning the condenser

Air Conditioner Option

Status: – Main switch open (OFF)

Material: – Not required
Equipment: – Crossheaded screwriver
– Soft bristle brush
– Vacuum cleaner
– Ecological solvent

m
Front view
.co
es
Preliminary procedures / notes
– The conditioner does not require any maintenance activities. Possible traces of
oil are symptom of leakages from the cooling circuit and replacement is
necessary (see card ACO: replacement).
uid

– The amount of dirt inside the conditioner depends on the quality of the insallation
environment air. The schedule in the maintenance plan refers to a typical
condition.
Before removing the conditioner cover, make sure the powers supply
is off and the inside fan is still.

We advise against using compressed air, due to the impossibility to

-g

check the amount of dirt removed, with the risk to direct it towards the
operators face.
all

Operating procedure
a. The cleaning includes the fan, condenser and environment air inlet and outlet
openings.
b. Unscrew the screws securing the conditioner cover.

c. Lift the cover and remove the earth wire connection.

d. Using a brush, remove the dirt while contemporaneously sucking with the
vacuum cleaner to collect the it. Possible persistent dirt may be removed using
an ecological solvent.

e. Make sure the condensate drainage opening and related pipe are not obstructed.

HS-RC-C5E-ACO_01.fm
46 00/0211
 All manuals and user guides at all-guides.com

Operating procedure
f. In cas the thermostat setting
gets accidentally modified,
reset the default value of 45 °C.

g. Replace the cover restoring the earth wire connection.

h. Screw back in place the cover fastening screws.

Follow-up procedure
– Not required

HS-RC-C5E-ACO_01.fm
00/0211 47
 All manuals and user guides at all-guides.com

Preventive Maintenance - ACO

7.6 ACO: emptying the condensate collectiong

can
Air Conditioner Option

Status: – Unimportant
Material: – Not required
Equipment: – Not required

Front view

Preliminary procedures / notes

– The emptying frequency depend on the environment humidity, therefore shall be
adjusted accondingly.

Operating procedure
a. Remove the pipe (A) from the
can (B).

b. Remove the can (B) from the

supporting item.

c. Open the plug and empty the

can in any water drain well.

d. Close the plug and replace the tank (B) in the supporting item.

e. Fit the pipe back in place.

Follow-up procedure
– Not required

HS-RC-C5E-ACO_03.fm
48 00/0211
 All manuals and user guides at all-guides.com

Preventive maintenance - E110

7.7 E110: fan cleaning

Fan

Status: – Main switch open (OFF)

Material: – Not required
Equipment: – 3-mm allen spanner
– Soft bristle brush
– Vacuum-cleaner
– Gloves

Front view

Preliminary procedure/ notes

– To ensure the control unit smooth operating, it is necessary to guarantee the
efficiency of the cooling system.
– The amount of dirt on the cooling fan depends on the quality of the air circulating
in the installation area. The times specified in the maintenance plan apply to a
typical situation.
Before removing the panel, make sure the power is disconnected and
the fan is still.

We do not advise using compressed air, as it does not allow to

control the dirt removed, that could hit the operator face.

Operating procedure
a. The cleaning procedure involves the fan and adjacent area.
b. Remove the Upper panel (see par. 5.3.2 on page 37) to reach the upper area.

c. Remove the dirt using a brush and contemporaneously suck the dirt with the
vacuum-cleaner.

HS-RC-C5E-E110_01.fm
49 00/0309
 All manuals and user guides at all-guides.com

Operating procedure
d. The area to be cleaned is the
fan (A) one.
Be careful and make
sure the X120 terminal
board is not powered.

e. Remove the dirt using the

brush, in particular on the fan
(A) blade inside area.

f. Mount the Upper panel (see

par. 5.3.2 on page 37) back.

g. If dirt is detected inside the cabinet, check the seal status. Refer to par. 7.4 ACC:
door closing and seal efficiency check on page 45.

Follow-up procedure
– Not required

HS-RC-C5E-E110_01.fm
50 00/0309
 All manuals and user guides at all-guides.com

Preventive maintenance - E111..E114

7.8 E111..E114: fan cleaning

Fan

Status: – Main switch open (OFF)

Material: – Not required
Equipment: – 3-mm allen spanner
– Soft bristle brush
– Vaccum-cleaner
– Gloves

m
Rear view
.co
es
Preliminary procedures / notes
– To ensure the control unit smooth operating, it is necessary to guarantee the
efficiency of the cooling system.
– The amount of dirt on the cooling fans and channel depends on the quality of the
uid

air circulating in the installation area. The times specified in the maintenance plan
apply to a typical situation.
Before removing the panel, make sure the power is disconnected and
the fans are still.

Be careful, as the recovery resistance may be very hot.

-g

We do not advise using compressed air, as it does not allow to

control the dirt removed, that could hit the operator face.
all

Operating procedure
a. The cleaning procedure shall include fans, dissipator, air passage channel and
panel grids.
b. Remove the Rear panel (see par. 5.3.3 on page 38) to reach the cabinet rear
area.

c. Remove the dirt using a brush and contemporaneously suck the dirt with the
vaccum-cleaner.

HS-RC-C5E-E1xx_01.fm
51 00/0309
 All manuals and user guides at all-guides.com

Operating procedure
d. The area to be cleaned is the
fan (A) and dissipator (B) one.
Be careful, as the
recovery resistance
may be very hot.

e. Remove the dirt using the

brush, in particular on the fan
(A) blade inside area.

f. Remove the dirt from the panel

grids (C).

g. Mount the Rear panel (see par.

5.3.3 on page 38) back.

Follow-up procedure
– Not required

HS-RC-C5E-E1xx_01.fm
52 00/0309
 All manuals and user guides at all-guides.com

Preventive maintenance - UPS

7.9 UPS: replacing the battery

Uninterruptible Power Supply

Status: – Irrelevant *¹
Material: – Battery (see Tab. 9.2 - Uninterruptible
Power Supply (UPS) on page 92)
Equipment: – Cross-headed screwdriver

Front view

Preliminary procedures / notes

Handle the battery with care. Use only batteries supplied as spare
parts.
Do no damage the casing to prevent corrosive fluid leakages.

The flat battery pack shall be disposed of in compliance with the

environmental protection laws in force.

*¹ If optional modules are installed that do not allow to reach the UPS module, we
recommend turning the Control Unit off before carrying out the procedure (refer to
topic Main switch open (OFF)).

Operating procedure
a. The UPS module is usually reachable and there is no need to remove other
components. If this is the case go to step c.

b. In case of optional modules mounted frontally that hinder the access, we

recommend acting as follows:

b.1 turn the Control Unit off.

b.2 if possible, release the UPS module from the omega guide (releasing lever in the
upper part) passing behind the hindering components / plates and place the UPS
module on the electric cabinet inside base

b.3 or, remove the optional module on the far right to reach the UPS module from the
front. Normally it is not necessary to disconnect the option cables and it can be
moved on the side, allowing the operator to reach the module.

HS-RC-C5E-UPS_01.fm
53 00/0309
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

c. Remove the fuse before acting
on the module C5G-UPS (1).

d. Loosen the cover fastening

screw by 4-5 turns (2). If it is not
removed completely, it will be
easier to mount it back.

e. Lift and remove the battery

cover (3).

f. Disconnect (4) the cables from

the battery terminals.

g. Remove the battery by pulling

the tag (5).

h. Fit in the new battery and carry out the steps above in reverse order.

i. Connect the cable according to the polarity.

j. Fasten the cover and fit the slot in the screw pressing slightly.

k. Tighten the screw without overdoing.

l. Fit in the fuse.

HS-RC-C5E-UPS_01.fm
54 00/0309
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

m. If one or more modules have been removed:

m.1 Fasten the UPS module on the omega guide.

m.2 Mount back the removed option panel.

Transfer the flat batteries to the suitable waste collection sites.
For further details, please refer to Chap. Setting out of work and
dismantling procedure on page 97

Follow-up procedure
– The battery needs about 3 hours for a complete charge and therefore to be able
to operate again.
– During the charging period, the Control Unit may not be able to guarantee
controlled shutdowns in case of powering interruption. Always perform the
suitable shutdown software procedure.

HS-RC-C5E-UPS_01.fm
00/0309 55
 All manuals and user guides at all-guides.com

Special maintenance

8. SPECIAL MAINTENANCE
This chapter deals with the following topics:
– Precautions before starting
– Equipment and tools required
– Modules subject to special maintenance activities

m
8.1 Precautions before starting
– Read carefully the instructions in Chap.2. - Maintenance prescriptions on page 19

.co
The maintenance activities that are not described in the sheets below shall be
performed by Comau qualified staff.

8.2 Equipment and tools required

es
The minimum equipment necessary to carry out special maintenance activities on the
C5G Control Unit is:

Tab. 8.1 - Equipment and tools required

uid

Flat blade screwdriver set

Cross-headed screwdriver set
Allen spanner set (sizes in mm), including extension rods
Socket wrench set (sizes in mm)
Anti Static Wrist Strap Discharge band grounding
Personal Computer supporting the WinC4G software properly installed.
-g

Disk On Key or other storage support, connection via USB

If the whole Control Unit has to be replaced, lifting mean suitable for the installation
area (crane or lift truck)
all

HS-RC-C5E-MAN_05.fm
56 00/0211
 All manuals and user guides at all-guides.com

Special maintenance

8.3 Modules subject to special maintenance

activities
To replace possible damaged items, follow the procedures described in the
maintenance sheets below.
The sheets, in alphabetical order following the abbreviations, are to be found in Tab. 8.2.

Tab. 8.2 - Special maintenance activities

Activity / Sheet Ref.¹
ACO: replacement (see par. 8.4 on page 58)
AMS-APC820: module replacement and Compact Flash recovery (see par. 8.5 on page 63)
AMS-ASM32: module replacement (see par. 8.6 on page 69)
AMS-IAM: module replacement (see par. 8.7 on page 72)
AMS-PPS8: module replacement (see par. 8.8 on page 78)
HMK: replacing the hour-counter (see par. 8.9 on page 82)
SDM: module replacement (see par. 8.10 on page 84)
UPS: replacing the module (see par. 8.11 on page 89)

HS-RC-C5E-MAN_05.fm
00/0211 57
 All manuals and user guides at all-guides.com

Manutenzione straordinaria - ACO

8.4 ACO: replacement

Air Conditioner Opzion

Status: – Main switch open (OFF)

Material: – Conditioner coplete with box roof (see
Tab. 9.6 - Conditioning)
Equipment: – M8 male eyebolts, supplied with the
conditioner
– Lifting system with 40 kg capacity (ex.
crane), with 2 1-m long ropes with
hook / shackle (Note: inside diamter of
conditioner eyebolt is equal to 20 mm)
– Crossheaded screwdriver
– Bladeheaded medium screwdriver
– 3 mm Allen wrench

Front view

Preliinary procedures / notes

– The compressor lubrication oil needs to stabilize. For this reason allow at least 8
hours before setting the conditioner at work.
– The procedure may be applied both in case of replacement of the conditioning
device on the Control Unit roof and on the Application Box roof, adapting the
references to the Control Unit to the Application Box.

Operating procedure
a. On the conditioner, remove the
2 upper bombé-headed screws
(A) that cover the eyebolt holes.

b. On the conditioner, screw in the

2 M8 eyebolt (B) in the screws
place. The eyebolts are usually
supplied with the Control Unit (if
equipped with the option). In
case they are no longer
available, use the ones
supplied with the new
conditioner.

HS-RC-C5E-ACO_02.fm
58 00/0211
 All manuals and user guides at all-guides.com

Operating procedure
c. On the C5G, unscrew and
remove the 4 M12 female
eyebolts (C) on the roof.

d. On the C5G, unscrew the 2

TSEI M4 unlosable screws (D).

e. Disconnect the conditioner

connection cable inside the
box. it may be necessary to
remove 2 or more plastic
clamps (E). The cable is
connected un the terminal
board by the box base.

f. From inside the box disconnect

the earth wire connected to the
roof. The wire on the box
remains connected.

g. Remove the condensate

drainage pipe from the
collecting can and the eyebolt.

HS-RC-C5E-ACO_02.fm
00/0211 59
 All manuals and user guides at all-guides.com

Operating procedure
h. By means of 2 ropes and a
suitable lifting sustem, anchor
to the 2 eyebolts on the
conditioner. Lift perfectly
vertical, such as not to damage
the threaded bars that come out
the Control Unit, seat of the
removed eyebolts. Note: the
conditioner weighs 35 kg.
i. Place the conditioner removed
on the floor, remove the
anchoring system and lift and
place the new conditioner on
the Control Unit. Be careful with
the powering cable coming out
the conditioner and the earth
wire for the metallic roof
connection. Keep the
conditioner in front position (the
blind panel is located frontally).

j. Place the connection cable

tidily inside the Control Unit.

k. Fasten the cable using plastic

clamps(E).

HS-RC-C5E-ACO_02.fm
60 00/0211
 All manuals and user guides at all-guides.com

Operating procedure
l. Connect the cable end on the
terminal board (F) by the box
base according to the
numbering on the wires. The
connection is on the lower side.

m
.co
m. Restore the connsction of the roof eaarth wire.
n. On the C5G, crew in the 4 M12
female eyebolts (C) on the roof,
that are supplied with plastic
washers.

o. On the C5G, screw in the 2

es
TSEI M4 unloseable screws
(D).
uid

p. On the conditioner, remove the

2 M8 eyebolts (B) and screw in
their place the 2 bombè-headed
screws (A). Put the eyebolts in
the Control Unit pocket, not to
lose them.
-g
all

HS-RC-C5E-ACO_02.fm
00/0211 61
 All manuals and user guides at all-guides.com

Operating procedure
q. Fit the new condensate
drainage pipe in the eyebolt and
then in the collecting can. Be
careful to the pipe path, that
shall go downwards. Cut the
pipe eccess length.

r. Lift the conditioner front blind

panel and make sure the value
is set at 45 °C (default value).

s. Close the front panel.

Fllow-up procedure
– Make sure at least 8 hours have elapsed for the stabilisation (without conditioner
capsizing) before setting the conditioner at work.
– The conditioner start-up is performed only when the box door/s are in the closed
position controlled by limit switch/es.

HS-RC-C5E-ACO_02.fm
62 00/0211
 All manuals and user guides at all-guides.com

Manutenzione straordinaria - AMS-APC820

8.5 AMS-APC820: module replacement and

Compact Flash recovery
Acopos PC

Status: – Main switch open (OFF)

Material: – Module AMS-APC820
(see Tab. 9.3 - CPU, power supplies
and power modules a pag. 93)
Equipment: – Balde-headed flat screwdriver, short
(4 x 25)
– Blade-headed screwdriver (3 x 15 and
6 x 15)
– T-shaped 5-mm Allen wrench, length
250 mm
– Antistatic arm band

Front view

Preliminary procedures / notes

– The antistatic arm band can be connected on one of the pins available inside the
galvanized connector panel (CIP). The connection efficiency is guaranteed only
if the Control Unit is earthed.
– The antistatic band shall be worn during the Compac Flash mounting and
dismounting procedure. During the other activities the arm band is not required.

Operating procedure
a. Disconnect the connectors on
the module upper side.
Depending on the connector
type, it may be necessary:
– to unscrew the screws before
removing the connector
– (A): to press the tongue and
keep it pressed during the
removal procedure

b. Remove other possible connectors and/or flash disk USB in the USB ports of the
AMS-APC820.

HS-RC-C5E-AM-APC_01.fm
63 00/0211
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

c. Unscrew the Allen screw (F)
and remove it.

d. Unscrew the Allen screw (G)

until it idles. The screw is of
unsalable type and shall not be
removed.

e. Remove the module by slightly

moving away the lower part,
then lift it.

f. In case of resistance due to the

friction with the adjoining
modules:
– loosen all Allen screws of the
adjoining module.
– If that is not sufficient, keep on
loosening all screws of all
installed modules.

Illustrative picture with AMS-IAM module highlighted

HS-RC-C5E-AM-APC_01.fm
64 00/0211
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

g. Wear the antistatic arm band.

h. Remove the Compact Flash

fitted in slot 1.

i. To carry out the removal

procedure you shall open door
(H), that contemporaneously
lifts the Compact Flash (L).

j. On the new AMS-APC820

module fit the removed Compac
Flash back in slot 1 (M).

k. Make sure the module bottom wall and the supporting area on the dissipator are
both perfectly clean.
l. Mount the new module in the
slot hooking it first from the
upper part, then lower it while
pushing it against the
dissipator.

m. Tighten the Allen screw (G) by

5 Nm.

HS-RC-C5E-AM-APC_01.fm
00/0211 65
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

n. Tighten the Allen screw (F) by
5 Nm.

m
.co
o. Place back all connectors (A), making sure the fitting is followed by a sharp “click”
indicating the fitting has been completely accomplished.

p. Place back possible other connectors and Flash Disk USB that may have been
removed previously.

q. If necessary, refer to the connectors and modules table included in the diagram
es
posted inside the Control Unit door.

r. Lower the lexan lower cover on the module.

s. After replacing the AMS-APC820, the Control Unit starts up in minimum

configuration and many controls will not be available until the configuration
uid

updating procedure has come to its end (the parameters are resident on the
Compact Flash only).

t. Switch on the Control Unit and make sure the Programming terminal is operating
and working. If you are using a wireless Programming terminal, it may be
necessary to carry out the Pairing procedure, possibly advanced by the
emergency Unpairing one (the Pairing and Unpairing procedure are described in
-g

the Control Unit Usage Modalities manual).

u. On the Control Unit modal selector switch, select the PROG mode.
all

HS-RC-C5E-AM-APC_01.fm
66 00/0211
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

v. Loading the system
configuration:

v.1 Access the Setup Menu (key

L3). If necessary, use the
MORE key.

v.2 Press the softkey “Config” (key

F1)

v.3 Using the arrows, select item 2

“Load the configuration file
(Load)” and confirm by pressing
the Enter key

v.4 The “File” field automatically

highlights the configuration file
name and the related path (i.e.
UD:\sys\cnfg\NJ1_01007.C5G

v.5 Confirm the loading using the

OK softkey (key F5). The
loading is confirmed by the
message “Activity in progress”
that is displayed for a short
while.

HS-RC-C5E-AM-APC_01.fm
00/0211 67
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

w. Saving the system
configuration:

w.1 Do not exit the Setup Menu

w.2 Press the softkey “Config” (key

F1)

w.3 Using the arrows, select item 1

“Save the configuration file
(Save)” and confirm by pressing
the Enter key

w.4 The “File” field automatically

highlights the configuration file
name and the related path
shown previously (e.g.
UD:\sys\cnfg\NJ1_01007.C5G

w.5 Confirm the saving using the

OK softkey (key F5). The
loading is confirmed by the
message “Activity in progress”
that is displayed for a short
while.

x. Restarting the system:

x.1 Exit the Setup Menu (key L3)

x.2 In the Home screen, press the

softkey “Restart” (key F4)

x.3 Using the arrows, select item 1

“Complete (Cold)” and confirm
by pressing the Enter key

Follow-up procedure
– Do not stand under the Robot or in the areas nearby.
– Carry out some motion cycles at reduced speed to check the proper operating.
– Select the AUTO mode and check the proper operating at reduced speed.

HS-RC-C5E-AM-APC_01.fm
68 00/0211
 All manuals and user guides at all-guides.com

Manutenzione straordinaria - AMS-ASM32

8.6 AMS-ASM32: module replacement

Auxiliary Supply Module

Status: – Main switch open (OFF)

Material: – Module AMS-ASM32
(see Tab. 9.3 - CPU, power supplies
and power modules a pag. 93)
Equipment: – T-shaped 5-mm Allen wrench, length
250 mm

Front view

Preliminary procedures / notes

– Not required.

Operating procedures
a. Disconnect the connectors on
the module upper side.
Depending on the connector
type, it may be necessary:
– (A): to carry out a direct removal
(connector without fastening
systems)

b. Unscrew the Allen screw (F)

and remove it.

HS-RC-C5E-AM-ASM_01.fm
69 00/0211
 All manuals and user guides at all-guides.com

Operating procedures (Continua)

c. Unscrew the Allen screw (G)
until it idles. The screw is of
unloseable type and shall not
be removed.

d. Remove the module by slightly

moving the lower part, then lift
it.

e. In case of resistance due to the

friction with the adjoining
modules:
– loosen all Allen screws of the
adjoining module.
– If that is not sufficient, keep on
loosening all screws of all
installed modules.

I
llustrative picture with AMS-IAM module highlighted
f. Make sure the module bottom wall and the supporting area on the dissipator are
both perfectly clean.

HS-RC-C5E-AM-ASM_01.fm
70 00/0211
 All manuals and user guides at all-guides.com

Operating procedures (Continua)

g. Mount the new module in the
slot hooking it first from the
upper part, then lower it while
pushing it against the
dissipator.

m
.co
h. Tighten the Allen screw (G) by
5 Nm.
es
i. Tighten the Allen screw (F) by
uid

5 Nm.
-g
all

j. Place back all connectors (A).

k. If necessary, refer to the connectors and modules table included in the diagram
posted inside the Control Unit door.

l. Lower the lexan lower cover on the module.

Follow-up procedure
– Not required.

HS-RC-C5E-AM-ASM_01.fm
00/0211 71
 All manuals and user guides at all-guides.com

Manutenzione straordinaria - AMS-IAM

8.7 AMS-IAM: module replacement

Inverter Axis Module

Status: – Main switch open (OFF)

Material: – Modul AMS-IAMI
(see Tab. 9.3 - CPU, power supplies
and power modules a pag. 93)
Equipment: – Blade-headed flat screwdriver, short
(4 x 25)
– Blade-headed screwdriver (3 x 15 and
6 x 15)
– T-shaped 5-mm Allen wrench, length
250 mm
– Antistatic arm band

Front view

Preliminary procedures / notes

– The antistatic arm band can be connected on one of the pins available inside the
galvanized connector panel (CIP). The connection efficiency is guaranteed only
if the Control Unit is earthed.
– The antistatic band shall be worn during the transducer modules mounting and
dismounting procedure. During the other activities the arm band is not required.
– The images and explanations in the procedure refer to a AMS-IAM double
module. In case of single module, the no. of connectors and fastening screws is
to halved.

Operating procedure
a. Disconnect the connectors on
the module upper side.
Depending on the connector
type, it may be necessary:
– (A): to unscrew the screws
before removing the connector
– (B): to carry out a direct removal
(connector without fastening
systems)
– (C): to press the tongue and
keep it pressed during the
removal

HS-RC-C5E-AM-IAM_01.fm
72 00/0211
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

b. Disconnect the connectors on
the module lower side by
removing the connectors (D).

c. Unscrew the screws (E), lift the

terminal and move it away from
the module.

d. Unscrew the Allen screws (F)

and remove them.

e. Unscrew the Allen screws (G)

until they idle. The screws are of
unsalable type and shall not be
removed.

HS-RC-C5E-AM-IAM_01.fm
00/0211 73
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

f. Remove the module by slightly
moving away the lower part,
then lift it.

g. In case of resistance due to the

friction with the adjoining
modules:
– loosen all Allen screws of the
adjoining module.
– If that is not sufficient, keep on
loosening all screws of all
installed modules.

h. Wear the antistatic arm band.

i. Check the transducer (H)

module type. The abbreviation
is printed on the metallic front
area:

– Interface module
Encoder AMS-ETI22:
ENDAT 2.2 / AC0120-2

– Interface module
Resolver AMS-RTI:
Resolver / AC0122
j. Prepare a new axes module with interface module/s consistent with the removed
items.
k. The transducer interface module (e.g. module AMS-ETI22) may vary depending
on the module. We recommend to use new replacement items both for the
AMS-IAM module and the interface one, being very carefully not to change the
model.

HS-RC-C5E-AM-IAM_01.fm
74 00/0211
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

l. Open the front door (L) by
prizing on the upper area using
a screwdriver.

m. Record the IP address of

module AMS-IAM available on
the rotating selector switches
(M) to be able to set it in the new
module.

n. If necessary, remove the

interface module:

n.1 Using a screwdriver, push

gently upwards, prizing on the
inside tooth (J) available on the
interface module.

HS-RC-C5E-AM-IAM_01.fm
00/0211 75
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

n.2 Remove the module (K) while
keeping on pushing gently.

n.3 Repeat the procedure for the

second module.

m
.co
o. Make sure the module bottom wall and the supporting area on the dissipator are
both perfectly clean.
p. Mount the new module in the
slot hooking it first from the
upper part, then lower it while
pushing it against the
dissipator.
es
uid

q. Set the address.

r. Tighten the Allen screws (G) by
5 Nm.
-g
all

s. Tighten the Allen screws (F) by

5 Nm.

HS-RC-C5E-AM-IAM_01.fm
76 00/0211
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

t. Place back all connectors (C), making sure the fitting is followed by a sharp “click”
indicating the fitting has been completely accomplished.

u. Place back the connectors (B).

v. Place the connectors (A) back and the corresponding screws (tighten the screws
without overdoing).

w. Place the terminal back and tighten the screw (E).

x. Place the connectors back (D).

y. Place the connectors (A) back and tighten the corresponding screws (tighten the
screws without overdoing).
z. If necessary, refer to the connectors and modules table included in the diagram
posted inside the Control Unit door.

aa. Lower the lexan lower cover on the module.

ab. Set the IP address on the
rotating selector switches (M) of
module AMS-IAM according to
the values in the removed
module.

ac. Close back the door (L).

Follow-up procedure
– Do not stand under the Robot or in the areas nearby.
– Carry out some motion cycles at reduced speed to check the proper operating.
– Select the AUTO mode and check the proper operating at reduced speed.

HS-RC-C5E-AM-IAM_01.fm
00/0211 77
 All manuals and user guides at all-guides.com

Manutenzione straordinaria - AMS-PPS8

8.8 AMS-PPS8: module replacement

Passive Power Supply

Status: – Main switch open (OFF)

Material: – Module AMS-PPS8I
(see Tab. 9.3 - CPU, power supplies
and power modules a pag. 93)
Equipment: – T-shaped 5-mm Allen wrench, length
250 mm

Vista frontale

Preliminary procedures / notes

– Before replacing the module after diagnosing a non-functioning, we recommend
to check the efficiency status of the fuse (see Operating procedure (fuse status
check only) and Fuse fault symptoms and consequences).

Operating procedure (fuse status check only)

a. Lift the lower door covering the
cables and unscrew the fuse
carrier plug.

b. Check the fuse (F30) efficiency

status.

c. The fuse (F30) is of type:

– 30A, 600V, fast, 10.3 x 38 mm

Fuse fault symptoms and consequences

a. The fuse (F30) triggering cuts off the recovery resistance from the Bus-DC
causing the consequent overvoltage on the bus as well as error 7200, 7225, etc.

b. Such error can be caused also by the resistance connection interrupation or in

case of resistance fault (value equal to 14.96 ohm).

HS-RC-C5E-AM-PPS_01.fm
78 00/0411
 All manuals and user guides at all-guides.com

Operating procedure
a. Disconnect the connectors on
the module upper side.
Depending on the connector
type, it may be necessary:
– (A): to carry out the direct
removal (connector without
fastening systems)
– (B): to press the tongue and
keep it pressed during the
removal

b. Disconnect the connectors on

the module lower side by
removing the connectors (D).

c. Unscrew the Allen screws (F)

and remove them.

d. Unscrew the Allen screws (G)

until they idle. The screws are of
unloseable type and shall not
be removed.

HS-RC-C5E-AM-PPS_01.fm
00/0411 79
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

e. Remove the module by slightly
moving away the lower part,
then lift it.

f. In case of resistance due to the

friction with the adjoining
modules:
– loosen all Allen screws of the
adjoining module.
– If that is not sufficient, keep on
loosening all screws of all
installed modules.

Illustrating picture with AMS-IAM module highlighted

g. Make sure the module bottom wall and the supporting area on the dissipator are
both perfectly clean.
h. Mount the new module in the
slot hooking it first from the
upper part, then lower it while
pushing it against the
dissipator.

HS-RC-C5E-AM-PPS_01.fm
80 00/0411
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

i. Tighten the Allen screws (G) by
5 Nm.

m
.co
j. Tighten the Allen screws (F) by
5 Nm.
es
k. Place back all connectors (B), making sure the fitting is followed by a sharp “click”
uid

indicating the fitting has been completely accomplished.

l. Place back all connectors (A) and (D).

m. If necessary, refer to the connectors and modules table included in the diagram
posted inside the Control Unit door.
-g

n. Lower the lexan lower cover on the module.

Follow-up procedure
– Not required.
all

HS-RC-C5E-AM-PPS_01.fm
00/0411 81
 All manuals and user guides at all-guides.com

Special maintenance - HMK

8.9 HMK: replacing the hour-counter

Hour Meter Kit

Status: – Main switch open (OFF)

Material: – Hour-counter (see xxxxxxxxxxxxxx)
Equipment: – Flat blade screwdriver

Front view

Preliminary procedures / notes

– The hour-counter module records the Robot working hours. Record the value
displayed by the removed hour-counter and take it into account in the future
Robot periodic maintenance sessions.

Operating procedure
a. Press both side levers (A) on
the inside plastic frame.

b. Slip off the frame (B), while

acting on the levers.

HS-RC-C5E-HMK_01.fm
82 00/0309
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

c. Slip off the frame (B) while
acting on the levers.

d. Push the hour-counter

outwards.

e. Connect the wires to the new

hour-counter.

f. Place the new hour-counter in its seat and orient it properly.

g. Place the plastic frame back, while keeping the hour-counter in its seat, and push
it firmly in position.

Follow-up procedure
– Not necessary.

HS-RC-C5E-HMK_01.fm
00/0309 83
 All manuals and user guides at all-guides.com

Manutenzione straordinaria - SDM

8.10 SDM: module replacement

Safety Distribution Module

Status: – Main switch open (OFF)

Material: – Module SDM
(see Tab. 9.4 - Safety Distribution
Module (SDM) a pag. 94)
Equipment: – Flat blade-headed screwdriver, short
(4 x 25)
– Flat blade-headed screwdriver (3 x 15
e 6 x 15)
– T-shaped 5-mm Allen wrench, length
250 mm

Front view

Preliminary procedures / notes

– Not required.

Operating procedure
a. Disconnect the connectors on
the module upper area.
Depending on the connector it
may be necessary:
– to unscrew the screws before
removing the connector
– (A): to carry out a direct removal
(connector without fastening
systems)
– (B): to press the tang and keep
it pressed during the removal

b. Disconnect the connectors on

the module front side.
Depending on the connector it
may be necessary:
– (A): to carry out a direct removal
(connector without fastening
systems)
– (B): to press the tang and keep
it pressed during the removal
– (C): to unscrew the screws
before removing the connector

– Note: if options are installed, the connectors (A) and (B) may differ, as cabled
wires replace the standard version typical bridges.

HS-RC-C5E-SDM_01.fm
84 00/0411
 All manuals and user guides at all-guides.com

Operating procedure (Continue)

c. Disconnect the connectors on
the module lower side:
– (B): press the tang and keep it
pressed during the removal.

d. Unscrew by 2-3 turn the Allen

screw (F), but do not remove it.

e. Remove the module by slightly

lifting the lower part, then move
it away. The module is not
locked below.

HS-RC-C5E-SDM_01.fm
00/0411 85
 All manuals and user guides at all-guides.com

Operating procedure (Continue)

f. At the stand, remove possible connectors still available on the module and
serving as plugs or without connections, such as to guarantee the same
functionalities and performances for the new module as well (in particular
connectors with bridges). Fit them on the new module complying with the original
position.
g. Make sure the module bottom wall and the supporting area on the dissipator are
both perfectly clean.

m
h. Mount the new module in the
slot by fitting it through the
upper screw, then lower it
pushing it against the
dissipator.

.co
es
i. Tighten the Allen screw (F) by
5 Nm.
uid
-g

j. Set the time selected on the

stop circuit timer in the SDM
module rotating selector
switches (SW1 and SW2)
all

consistently with the values in

the module removed. Refer
also to Tab. 8.3 - Time to be set
depending on the Robot family
a pag. 88 and Tab. 8.4 - Time
and position for the rotating
selector switches on SDM
module a pag. 88.
Usage restrictions
– Take into account that the controlled time zeroing or reduction may result in:
• departures from the expected trajectory, due to the untimely triggering of the
motors waiting brakes.
• possible Robot stress, due to the motors waiting brake triggering, and
impacts caused by the departures from the expected trajectory.

HS-RC-C5E-SDM_01.fm
86 00/0411
 All manuals and user guides at all-guides.com

Operating procedure (Continue)

k. Place back connectors (A).

l. Place back all connectors (B), making sure the fitting is followed by a sharp “click”
indicating the fitting has been completely accomplished.

m. Place back all connectors (C) and screw the corresponding screws (tighten the
screws without overdoing).

n. If necessary, refer to the connectors and modules table included in the diagram
posted inside the Control Unit door.

Follow-up procedure
– Do not stand under the Robot or in the areas nearby.
– Carry out some motion cycles at reduced speed to check the proper operating.
– Select the AUTO mode and check the proper operating at reduced speed.

HS-RC-C5E-SDM_01.fm
00/0411 87
 All manuals and user guides at all-guides.com

Tab. 8.3 - Time to be set depending on the Robot family

Time to be set on SDM module
Robot family (preferential depending on the Robot family and typical
applications)
SMART 5 Six / NS
SMART 5 NM 1.5 seconds *¹
SMART 5 NJ
Square YZ-500 2 seconds
SMART NX1-600 2 seconds
SMART NX1-800 6 seconds

Tab. 8.4 - Time and position for the rotating selector switches on
SDM module
Time (seconds)
0 0,5 1 1,5 *¹ 2 2,5 3 4 5 6

SW1 / SW2
selector switch position 0 1 2 3 *¹ 4 5 6 7 8 9

*¹ Manufacturer’s default value.

HS-RC-C5E-SDM_01.fm
88 00/0411
 All manuals and user guides at all-guides.com

Special maintenance - UPS

8.11 UPS: replacing the module

Uninterruptible Power Supply

Status: – Main switch open (OFF)

Material: – Complete Module C5G-UPS (refer to
Tab. 9.2 - Uninterruptible Power
Supply (UPS) on page 92)
Equipment: – Cross-headed screwdriver

Front view

Preliminary procedures / notes

Handle the module with care as it hosts a battery.

This module hosts a battery and shall be disposed of in compliance

with the environmental protection principles and laws in force. For
further details about the battery removal, refer to par. 10.5 Removing
the pile and battery from the Control Unit on page 99.
– Before replacing the UPS module due to an alleged fault, make sure it cannot be
ascribed to the battery protection fuse installed on the module.

Operating procedure
a. The UPS module is usually reachable and there is no need to remove other
components. If this is the case go to step c.

b. In case of optional modules mounted frontally that hinder the access, we

recommend acting as follows:

b.1 if possible, release the UPS module from the omega guide (releasing lever in the
upper part) passing behind the hindering components / plates and place the UPS
module on the electric cabinet inside base

b.2 or, remove the optional module on the far right to reach the UPS module from the
front. Normally it is not necessary to disconnect the option cables and it can be
moved on the side, allowing the operator to reach the module.

HS-RC-C5E-UPS_02.fm
89 00/0309
 All manuals and user guides at all-guides.com

Operating procedure (Continued)

c. Remove the upper (1) and
lower (2) connectors.

d. Replace the UPS module.

e. Connect the connectors back to

the original position.

f. Fasten the UPS module on the omega guide.

g. If one or more modules have been removed:

g.1 Mount back the removed option panel.

Transfer the UPS module and battery to the suitable waste collecting
sites.
For further details refer to Chap. Setting out of work and dismantling
procedure on page 97

Follow-up procedure
– The battery needs about 3 hours for a complete charge and therefore to be able
to operate again.
– During the charging period, the Control Unit may not be able to guarantee
controlled shutdowns in case of powering interruption. Always perform the
suitable shutdown software procedure.

HS-RC-C5E-UPS_02.fm
90 00/0309
 All manuals and user guides at all-guides.com

Spare parts

9. SPARE PARTS
This chapter deals with the following topics:
– Precautions about the spare part usage
– Where to procure the spare parts
– Spare part list

m
– Spare parts for the C5G basic model

9.1 Precautions about the spare part usage

.co
Find in this chapter the spare part list divided per module.
If not clearly specified, the spare part suits all Unit Control sizes.

Use only original spare parts for the C5G Control Unit, in particular for the devices
installed in the status and safety circuits.
es
Do not carry out independent or unauthorized activities on damaged modules.
Repairs shall be performed by Comau staff only.
Do not use the spare parts for purposes other than the ones specified.
uid

The spare part features and performances are to be regarded as valid only if the
spare part is used according to the specifications in the Instruction Manuals
related to the C5G Control Unit.
The Control Unit Compliance Statements apply also to the single spare parts, if
the latter are used according to the specifications in the Instruction Manuals
related to the C5G Control Unit.
-g

9.2 Where to procure the spare parts

The original spare parts can be purchased through the Comau Customer Center.
all

9.3 Spare part list

– Spare parts for the C5G basic model
• Arm Controller Electromechanical (ACE)
• Uninterruptible Power Supply (UPS)
• CPU, power supplies and power modules
• Safety Distribution Module (SDM)
• Internal ventilation system
• Conditioning

HS-RC-C5E-MAN_06.fm
00/0411 91
 All manuals and user guides at all-guides.com

Spare parts

9.4 Spare parts for the C5G basic model

Tab. 9.1 - Arm Controller Electromechanical (ACE)

Item Comau code Description

CR19191126 PKZMO-25 main circuit breaker 25 A (Q100)

A PKZO-XH-MCC black handle, 90° turned switch and extension
CR19191127
(Q100)
B CR10140283 EMI filter 8kW 30 A 520 Vac (Z1)

Tab. 9.2 - Uninterruptible Power Supply (UPS)

A B

Item Comau code Description

A CR10140583 C5G-UPS complete

B CR10142483 C5G-UPS blade fuse 30 A (green)

C CR10142283 C5G-UPS battery 12 V 5 Ah, 70 x 106 x 90 mm (W x H x D)

HS-RC-C5E-MAN_06.fm
92 00/0411
 All manuals and user guides at all-guides.com

Spare parts

Tab. 9.3 - CPU, power supplies and power modules

E
H

G
J

AB CD F

Item Comau code Description

AMS-APC820
A CR10140783
(identified on the module front part as ACOPOS multi APC820)
AMS-PPS8 Passive Power Supply 8 KVA
B CR10140383
(identified on the module front part ACOPOS multi P0220)
AMS-ASM32 Auxiliary Supply Module 32 A / 24 Vdc
C CR10140483
(identified on the module front part ACOPOS multi C0320)
AMS-IAM22+22 Inverter Axis Module 22/85 +22/8
CR10141583
(identified on the module front part ACOPOS multi I0220D)
AMS-IAM11+11 Inverter Axis Module 11/43 +11/43
CR10141483
(identified on the module front part ACOPOS multi I0110D)
D *¹
AMS-IAM5,5+5,5 Inverter Axis Module
CR10141283
(identified on the module front part ACOPOS multi I0055D)
AMS-IAM 2,8+2,8 Inverter Axis Module
CR10141183
(identified on the module front part ACOPOS multi I0028D)
AMS-ETI22 ETI Encoder Trasducer Interface ENDAT2.2
E *² CR10140883
(identified on the module front part Endat 2.2 AC0120-2)

HS-RC-C5E-MAN_06.fm
00/0411 93
 All manuals and user guides at all-guides.com

Spare parts

Tab. 9.3 - CPU, power supplies and power modules (Continued)

Item Comau code Description
AMS-RTI Resolver Trasducer Interface
E *² CR10141683
(identified on the module front partResolver / AC0122)
F CR10140183 AMS-FMP14 Feed-through Mounting Plate 14 slots
G *³ CR10141983 AMS-AFU ACOPOS Fan Unit

H CR10142383 C5G-APC Lithium Battery 3V 950 mAh

J -- Fuse 30A, 600V, fast, 10.3 x 38 mm

L CR19191128 C5G-ERR Energy Recovery Resistance 15 ohm 2 kW

*¹ Position and no. depending on the installed axes power
*² Alternative, depending on the type of transducer on the motor
*³ Fan standardized for all modules:
– no. 2 installed in the module AMS-APC820
– no. 1 installed in each module AMS-PPS8, AMS-ASM 32
– no. 1 or 2 installed in each module AMS-IAM xx, depending on the no. of slot taken
by the module.

Tab. 9.4 - Safety Distribution Module (SDM)

Item Comau code Description

A CR17430080 C5G-SDM Safety & Distribution Module

HS-RC-C5E-MAN_06.fm
94 00/0411
 All manuals and user guides at all-guides.com

Spare parts

Tab. 9.5 - Internal ventilation system

Position Comau code Description

A CR17430981 C5G-IFK Inside fan kit (E110)

B CR17431081 C5G-FCK Cooling fan kit (E111, E112, E113, E114)

HS-RC-C5E-MAN_06.fm
00/0411 95
 All manuals and user guides at all-guides.com

Spare parts

Tab. 9.6 - Conditioning

Codice: COMAU CR17133680

m
B

Position Comau Code

.co C

Description
es
C5G-ACG Conditioner Unit complete with conditioner, metallic
A CR17431880
roof and powering cable for conditioner.
Bipolar limit switch 1NO+ 1NC, NEW ELFIN 50F11
B -- Note: the limit switch model is identical also when installed in the
Application Box
uid

C -- IMagneto.thermal switch curve D 2,5-4A, SQUARE D - GV2-P08

D CR19900028 Condensate collecting flask

-g
all

HS-RC-C5E-MAN_06.fm
96 00/0411
 All manuals and user guides at all-guides.com

Setting out of work and dismantling

10. SETTING OUT OF WORK AND

DISMANTLING
This chapter deals with the following topics:
– Precautions before starting
– Staff to set the plant out of work and dismantle it
– Equipment and tools required
– Setting out of work and dismantling procedure
– Removing the pile and battery from the Control Unit

10.1 Precautions before starting

The robot system (consisting of Robot and Control Unit) shall be dismantled in
compliance with the environmental prescriptions and according to the methodologies in
force in the land where it is installed.
Prepare different containers to collect the different materials separately.

10.2 Staff to set the plant out of work and

dismantle it
The staff that shall perform the dismantling shall be suitably trained, in order to be able
to use the lifting means properly.
Moreover, the staff shall be warned or trained (in electrics) and therefore be aware of
the dangers associated with electric energy and of the measures to be taken when
working on electric connections.

10.3 Equipment and tools required

– Ordinary mechanical and electric equipment.
– Containers.

10.4 Setting out of work and dismantling

procedure
In this section are described the main steps to perform the robot system dismantling at
the end of its operating life.
The activities below are to be carried out by the Staff to set the plant out of work and
dismantle it only:

a. create around the robot system sufficient space to perform all movements without
endangering the staff

b. move the robot to transport position and mount the axes locking items (if present),
following the instructions on the plate posted on the robot and its Technical
Documents.

HS-RC-C5E-MAN_07.fm
00/0309 97
 All manuals and user guides at all-guides.com

Setting out of work and dismantling

c. open the Control Unit main switch and lock it in open position

d. disconnect the electric power at the distribution source and lock the switch in open
position.

e. disconnect the powering cable from the Control Unit; disconnect the power wires
first and then the earth one

f. disconnect the multipolar connectors by the Control Unit and Robot sides

g. if installed, disconnect the pneumatic system from the distribution network and
blow off the residual air

h. before moving the Robot and Control Unit, we recommend to remove possible
batteries, oils and other chemicals (found procedure and location in the next
sections)

i. read carefully and follow the instructions in the chemicals safety sheets not to
endanger the operator and to avoid polluting the environment

The disposing activities shall be carried out in compliance with the laws in force
in the land where the machine is installed: dispose of batteries, oils and
chemicals according to the environmental laws and transfer them to the suitable
waste collecting sites.

j. Remove the robot and Control Unit from the working area, following all
prescriptions in the product Technical Documents; in case of lifting, check the
eyebolts fastening and use only suitable slinging devices and equipment

k. Move the Robot and Control Unit to the area intended for the dismantling and
disposing procedures.

l. If the procedure is to be carried out independently, disassemble the components

from up downwards and act with particular care when handling machine units/parts
that may fall due to gravity

Act carefully, to avoid possible parts or components falling during the removal
phase, as this could severely endanger the operators.

m. remove the parts and separate, as much as possible, the different components
based on the materials (plastic, metal, electronic modules, piles, batteries, etc.)
that shall be disposed of applying the waste separation principle. Transfer the
materials resulting from the dismantling to duly authorized company

The disposing activities shall be performed in compliance with the laws in force
in the land where the machine is installed: dispose of electronic cards and
ferrous/plastic materials according to the law prescriptions and transfer them to
the suitable waste collecting sites.
In case of problems while carrying out the component disassembling,
dismantling and disposing procedures, turn to the manufacturer’s design
technical dept., which will specify the operating modalities in compliance with the
safety and environmental protection principles.

HS-RC-C5E-MAN_07.fm
98 00/0309
 All manuals and user guides at all-guides.com

Setting out of work and dismantling

10.5 Removing the pile and battery from the

Control Unit
Status: – Power off
Material: – Not necessary
Equipment: – Blade screwdriver
– Star-shaped blade screwdriver
– Container

B
C

Preliminary procedures / notes

– The disposing activities shall be carried out in compliance with the laws in force
in the land where the machine is installed: dispose of batteries and piles
according to the environmental protection prescriptions and transfer them to the
suitable waste collecting sites
– The Control Unit features the following piles /batteries:
• Button-shaped pile in the module AMS-APC820 (reference A)
• Battery in the module C5G-UPS (reference B)
• Battery in the WiTP Programming terminal (reference C).

Operating procedure
Button-shaped pile in the module
AMS-APC820 (reference A)

a. Lift the front item of module

AMS-APC820.

b. Open the lower door.

c. Remove the button-shaped pile

pulling the tag.

HS-RC-C5E-MAN_07.fm
00/0309 99
 All manuals and user guides at all-guides.com

Setting out of work and dismantling

Operating procedure (Continued)

Battery in the module C5G-UPS
(reference B)

a. Remove the fuse before acting

on module C5G-UPS.

b. Remove the cover fastening

screw.

c. Remove the battery cover.

d. Disconnect the cables from the

battery terminals.

e. Remove the battery pulling the

tag.

HS-RC-C5E-MAN_07.fm
100 00/0309
 All manuals and user guides at all-guides.com

Setting out of work and dismantling

Operating procedure (Continued)

Battery in the WiTP Programming
terminal (reference C)

a. Open the programming terminal

removing the fastening screws.

b. Remove the screws and items

that lock the battery.

m
c. Lift the battery and disconnect
the side connector.

.co
Follow-up procedure
Transfer piles and batteries to the suitable waste collecting sites.
es
uid
-g
all

HS-RC-C5E-MAN_07.fm
00/0309 101
All manuals and user guides at all-guides.com
 All manuals and user guides at all-guides.com

COMAU Robotics services

Repair: [email protected]
Training: [email protected]
Spare parts: [email protected]
Technical service: [email protected]
comau.com/robotics Original instructions