Masteremaco N 303 Tds

MasterEmaco N 303
Single component polymer modified fairing coat / cosmetic mortar for concrete surfaces
MATERIAL DESCRIPTION
MasterEmaco N 303 is a single component acrylic Failure to comply with the recommended storage
polymer modified repair mortar for use as a "fairing coat" conditions may result in premature deterioration of the
or cosmetic mortar. When mixed with water, as directed, product or packaging. For specific storage advice consult
a fine grey trowelable mortar results which can readily be Master Builders Solutions Construction Chemicals SA’s
applied to fill in pores, blowholes and blemishes on a Technical Services Department.
concrete surface. MasterEmaco N 303 can be used as a
'skim' coat prior to the application of protective coatings. TYPICAL PROPERTIES *
MasterEmaco N 303 is specially formulated to produce a Plastic density 1800kg/m³

shrinkage compensating mortar with no cracking when Compressive strength at 28 days 20N/mm²
applied in a thin section. Adhesion to concrete and * Properties listed are only for guidance and are not a
flexibility are excellent. guarantee of performance.
PRIMARY USES APPLICATION

As a fairing or skim coat to cover and make good MasterEmaco N 303 should be applied to the complete
blemishes in concrete surfaces such as slight area with the minimum of trowelling. Leave for a short
honeycombing, blowholes, defects caused by 'sand runs', period before final trowelling. Finishing may be aided by
patch repairs, shutter movement and grout loss. flicking a small amount of water onto the surface, using a
paint brush before final trowelling.
• Preparatory treatment to concrete to receive a thin film
protective coating.
• To produce a uniform surface over repaired areas. When used as a "scraper coat" MasterEmaco N 303 can
be applied with a brush or roller and then the excess
ADVANTAGES scraped off with the edge of a steel float. In this way blow
• Precision made, consistent results. holes and minor blemishes in an otherwise fair faced
• Requires only the addition of mixing water. concrete can be hidden.
• Shrinkage compensating.
• Excellent adhesion to concrete.
• Flexible. CURING
• Smooth, easily produced finish. Good curing practice is essential even though
• Low permeability. MasterEmaco N 303 is specially formulated to prevent
• Stadium Grey colour available.
shrinkage and cracking. Particular care is required in hot
• Excellent resistance to freeze / thaw action and
carbonation. and windy conditions. Cure with a single coat of
• Ingress of water borne salts, such as chloride and MasterKure 181 which is compatible with most
atmospheric / chemical attack. subsequent protective coatings, or by covering the work
• Subsequent paint coats can be applied with greater with properly secured plastic sheeting or with water.
economy.
PACKAGING PREPARATION
It is essential that the surfaces to be bonded are sound,
20kg bags – yield 12.8 litres.
clean and uncontaminated. All loose powdering material
must be removed. Concrete surfaces should be
STORAGE
thoroughly soaked prior to application of MasterEmaco N
Store under cover, out of direct sunlight and protect from
303, to ensure a saturated, but surface dry condition.
extremes of temperatures.
Shelf life:
12 months from date of manufacture.
March 21 Page 1 of 2
MasterEmaco N 303
Single component polymer modified fairing coat / cosmetic mortar for concrete surfaces
VOID FILLING product or packaging. For specific storage advice consult

Deeper voids should be filled prior to the application of a Master builders Solutions’ Technical Services
cosmetic coating by reducing the amount of water added Department.
when mixing to produce a trowelable putty like mortar.
SAFETY PRECAUTIONS
MIXING As with all chemical products, care should be taken during
MasterEmaco N 303 is formulated to give an easily mixed use and storage to avoid contact with eyes mouth, skin
material. For full bag quantities, it is preferable to mix the and foodstuffs (which can also be tainted with vapour until
material in a Crete angle or similar forced action mixer. product is fully cured or dried). Treat splashes to eyes and
Alternatively, a slow speed, handheld electric mixer with a skin immediately. If accidentally ingested, seek immediate
suitable paddle can be used. Over mixing should be medical attention. Keep away from children and animals.
avoided. The powder should be placed in the mixing Reseal containers after use.
vessel and mixing commenced. Clean water should be
slowly added up to the recommended maximum or until NOTE
the required consistency is achieved. No more than 5.6 Technical support, where provided, does not constitute
litres of water per 20kg of MasterEmaco N 303 should be supervisory responsibility. For additional information
added. (W/P ratio = 0.28). contact your local MB Construction Chemicals Solutions
South Africa (Pty) Ltd representative. MB Construction
COVERAGE Chemicals Solutions South Africa (Pty) Ltd shall not be
One 20kg bag of MasterEmaco N 303 will typically yield liable for technical advice provided.
12.8 litres of mortar and will cover approximately 5.04m²
at 2.5mm thickness. MB Construction Chemicals Solutions South Africa (Pty)
Ltd reserves the right to have the true cause of any
EQUIPMENT CARE difficulty determined by accepted test methods.
Tools should be washed with water immediately after use. Undertaking such tests is not, and shall not be deemed to
be, an admission of liability or an assumption of any risk,
SURFACE FINISHING loss, damage or liability.
All slight surface imperfections should be made good by
the application of MasterEmaco N 303 as manufactured QUALITY AND RESPONSIBLE CARE
by Master Builders Solutions. Applications should be All products originating from MB Construction Chemicals
strictly in accordance with the manufacturer's instructions. Solutions South Africa (Pty) Ltd are manufactured under
a management system independently certified to conform
STORAGE to the requirements of the quality standards ISO 9001,
Store under cover, out of direct sunlight and protect from environmental and occupational health and safety
extremes of temperatures. Shelf life of 12 months from standards.
date of manufacture.
* Properties listed are based on laboratory controlled
Failure to comply with the recommended storage tests.
conditions may result in premature deterioration of the
DISCLAIMER
The technical information and application advice given in this MB Construction Chemicals Solutions South Africa (Pty) Ltd
publication are based on the present state of our best scientific and practical knowledge. As the information herein is of a
general nature, no assumption can be made as to a product's suitability for a particular use or application and no warranty
as to its accuracy, reliability or completeness either expressed or implied is given other than those required by law. The user
is responsible for checking the suitability of products for their intended use.
March 21 Page 2 of 2

Masteremaco N 303 Tds

Uploaded by

Copyright:

Available Formats

Masteremaco N 303 Tds

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Masteremaco N 303 Tds

Uploaded by

Copyright:

Available Formats

MasterEmaco N 303

MasterEmaco N 303 is specially formulated to produce a Plastic density 1800kg/m³

PRIMARY USES APPLICATION

VOID FILLING product or packaging. For specific storage advice consult

You might also like