Movil 67 Terminadora de Asfalto

RP-180
Rubber Tire
Asphalt Paver
Operation and Service Manual
<
PN 262899 © ROADTEC INC. October 2005

SN
RP-180 Rubber Tire Asphalt Paver
OPERATION AND SERVICE MANUAL
RP-180
MODEL _____________
SERIAL NUMBER _____________
DATE PURCHASED _____________
Paver Operation & Service Manual 3
Document Title RP-180_OPSERV_SN 4073~
First Release October 2005
Part Number 262899
Copyright Copyright © 2005

All rights reserved. All contents in
this Manual are copyright protected
by Roadtec, Inc.
Reproduction, duplication, translation
or storage, in whole or in part, is not
permitted without the prior written
consent of Roadtec, Inc.
Copyright © 2005
PN 262899 Version # 1
Publisher Roadtec, Inc.

An Astec Industries Company
800 Manufacturers Road
Chattanooga, TN 37405
Roadtec.com
4 Paver Operation & Service Manual

Contents
1.0 Contents
RP-180 Rubber Tire Asphalt Paver................................................................. 11
STANDARD WARRANTY ................................................................................... 13
Proposition 65 Warning ................................................................................... 15
1�0 Introduction �� 17
1.01 Preface .................................................................................................19
1.02 Description .............................................................................................21
1.03 Inspect a New Machine.............................................................................23
1.04 Unit Nomenclature ...................................................................................25
1.05 Machine Dimensions ................................................................................27
.............................................................................29
1.07 Engine Systems ......................................................................................31
1.08 Drive System ..........................................................................................33
1.09 Material Feed System ...............................................................................35
1.10 Electrical System .....................................................................................37
1.11 Optional Equipment .................................................................................39
2�0 Safety �� 41
2.01 Safety Features .......................................................................................43
2.01.01 Machine Danger Zones ......................................................................45
2.02 Safety Requirements................................................................................47
2.03 Wear Personal Protective Equipment (PPE) ..................................................48
2.04 Commit to 100% Safety ...........................................................................48
2.05 Learn Safety ...........................................................................................49
2.06 Know the Rules .......................................................................................49
2.07 Perform Quality Inspections ......................................................................50
2.08 Know the Machine ...................................................................................50
2.09 Prevent Fires ..........................................................................................51
2.10 Know the Job Site....................................................................................51
2.11 Load/Unload Safely ..................................................................................52
2.12 Mount and Start Safely.............................................................................52
2.13 Focus on Safety.......................................................................................53
2.14 Practice Ground Operation Safety ..............................................................53
2.15 Be Safe Around Fumes .............................................................................54
2.16 Work Safely ............................................................................................54

Contents
2.17 Work Safely At Night ................................................................................55

2.18 Park Safely .............................................................................................55
2.19 Maintenance Safely..................................................................................56
2.20 Take Precautions .....................................................................................56
2.21 Service Battery Safely ..............................................................................57
2.22 Safely Service Electric Systems .................................................................57
2.23 Safely Service Hydraulic Systems ..............................................................58
2.24 Material Safety Data Sheets (MSDS) ..........................................................58
2.25 Safety First .............................................................................................58
2.26 Hazard Decals .........................................................................................59
3�0 Operation �� 63
3.01 Principles of Operation .............................................................................65
3.02 Operator Station .....................................................................................69
3.03 Left Seat/Left Side, Right Seat/Right Side Operator Console ..........................70
3.04 Left Seat/Right Side, Right Seat/Left Side Operator Console ..........................74
3.05 Machine Control Screen ............................................................................77
3.05.01 Main Screen .....................................................................................78
....................................79
3.05.03 Menu Options ...................................................................................80
3.05.04 Set Up Screed Boost .........................................................................81
3.05.05 Set Units of Measure .........................................................................82
3.05.06 SCR Exhaust System Cleaning (Regen) Modes ......................................83
3.05.06.01 SCR Engine Exhaust System Cleaning (Regen) ...............................84
3.05.06.02 Perform Forced Regen .................................................................87
3.05.06.03 Diesel Exhaust Fluid Indication Lamp ............................................88
3.05.06.04 SCR System Tampering / Malfunction Inducements .........................90
3.06 Left Screed Control Box ............................................................................92
3.07 Right Screed Control Box ..........................................................................93
3.08 Screed Digital Display - Main Screen ..........................................................94
3.09 Screed Digital Display - Auger Raise Screen ................................................95
3.10 Screed Digital Display - Flow Gate Height Screen .........................................96
3.11 Screed Digital Display - Screed Settings Screen ...........................................97
3.12 Screed Digital Display -Screed Offset and Min. Generator ..............................98
3.13 Remote Screed Box .................................................................................99

Contents
3.14 Pre-Start Conditions .............................................................................. 101

3.15 Pre-Start Check List ............................................................................... 103
3.16 Pre-Start Communication ....................................................................... 105
3.17 Screed Operations ................................................................................. 106
3.18 Prepare the Screed ................................................................................ 107
3.19 Screed Set Up ....................................................................................... 108
3.20 Feed System Set Up .............................................................................. 112
3.21 Paving Techniques ................................................................................. 115
3.22 Create Quality Transverse Joints .............................................................. 119
3.23 Auger Extensions................................................................................... 124
3.24 Paving for Smoothness Tips .................................................................... 127
3.25 Drive-Off Procedure ............................................................................... 129
3.26 Operate ............................................................................................... 131
3.27 Park and Shut Down .............................................................................. 137
4�0 Lubrication & Maintenance �� 139
4.01 Service Summary ................................................................................. 141
4.01.01 Service Safely ................................................................................ 142
4.02 Fluid Requirements ................................................................................ 143
4.03 Daily Maintenance ................................................................................. 145
............................................................................. 147
................................................................ 148
4.03.03 Check Engine Crankcase .................................................................. 149
4.03.04 Check Engine Oil Level..................................................................... 150
4.03.05 Check Engine Coolant Level .............................................................. 151
4.03.06 Lubricate Conveyor Idler and Headshaft Bearings ................................ 152
4.03.07 Lubricate Screed Vibrator Bearings ................................................... 153
4.03.08 Lubricate Auger Hanger and Chain Case Bearings ................................ 154
4.03.09 Check Hydraulic Tank Oil Levels ........................................................ 155
4.04 50 Hours Maintenance............................................................................ 157
4.04.01 Check/Replace Engine Air Intake Filter ............................................... 159
4.04.02 Change Hydraulic Filters .................................................................. 160
............................................... 161
4.04.04 Lubricate Screed Endgate Jacks ........................................................ 162
4.04.05 Lubricate Angle of Attack Mechanisms ............................................... 163

Contents
4.04.06 Lubricate Angle of Attack Threads ..................................................... 164

4.04.07 Lubricate Screed Crown Threads ....................................................... 165
4.04.08 Lubricate Strike-off Tube .................................................................. 166
4.04.09 Check Tire Pressure ........................................................................ 167
4.04.10 Lubricate Crown Control .................................................................. 168
4.05 100 Hours Maintenance .......................................................................... 169
4.05.01 Change Engine Oil and Oil Filter ........................................................ 171
4.06 250 Hours Maintenance .......................................................................... 173
4.06.01 Check/Replace Engine Air Intake Filter ............................................... 175
4.06.02 Change Engine Oil and Oil Filter ........................................................ 176
4.06.03 Change Engine Fuel Filter ................................................................ 178
4.06.04 Change Hydraulic Filters .................................................................. 179
4.06.05 Change Wheel Planetary Oil ............................................................. 180
4.06.06 Change Pump Drive Gearbox Oil ....................................................... 181
4.06.07 Change Auger and Conveyor Planetary Oil .......................................... 182
4.06.08 Lubricate Seat Pivot Bearing ............................................................. 183
4.07 1000 Hours Maintenance ....................................................................... 185
4.07.01 Flush and Clean Radiator ................................................................. 187
4.07.02 Replace Engine Breather .................................................................. 188
4.07.03 Flush Hydraulic Tank and Replace Strainer .......................................... 189
................................................... 191
............................................. 192
............................... 193
............................................... 194
4.08 2000 Hours Maintenance ........................................................................ 195
4.08.01 Diesel Emissions Fluid Filters ............................................................ 197
4.09 Maintenance Procedures ......................................................................... 199
4.09.01 Machine Lifting Points ...................................................................... 201
4.09.02 Machine Tie Down Points .................................................................. 202
4.09.03 Adjust Auger Drive Chain ................................................................. 203
4.09.04 Adjust Conveyor Drive Chain ............................................................ 206
4.09.05 Adjust Conveyor Drag Chain ............................................................. 207
4.09.06 Wash Down Machine........................................................................ 208
4.09.07 Manual Hood Raise and Brake Release ............................................... 210

Contents
4.09.08 Engage / Disengage Propel Pump Bypass ........................................... 212

4.09.09 Pivot Seats with Manual Hand Pump .................................................. 213
4.10 Wear Parts Guide................................................................................... 214
4.11 Chain Wear Guide .................................................................................. 215
5�0 Hydraulic Systems �� 217
5.01 Hydraulic Pump Drive System ................................................................. 219
5.01.01 Auxiliary Pump ............................................................................... 221
5.01.02 Propel Pumps ................................................................................. 222
5.01.03 Conveyor Pumps ............................................................................. 223
5.01.04 Screed Generator Pump ................................................................... 224
5.01.05 Radiator Fan Pump .......................................................................... 225
5.02 Motors ................................................................................................. 227
5.02.01 Auger and Conveyor Motors ............................................................. 229
5.02.02 Propel Drive Motors ......................................................................... 230
5.02.03 Fume Extraction Motors ................................................................... 231
5.02.04 Radiator Fan Motor .......................................................................... 232
5.03 Valves .................................................................................................. 233
5.03.01 Brake Shift, Hood Valve Stack........................................................... 235
5.03.02 Rear Valve Stack ............................................................................. 236
5.03.03 Tow Point Valves ............................................................................. 237
5.03.04 Differential Lock Valve ..................................................................... 238
5.03.05 Screed Assist/Screed Boost Valve ...................................................... 239
5.03.06 Hydraulic Tunnel Extension Valve ...................................................... 240
6�0 Maintenance Charts �� 241
6.01 Daily Maintenance Chart ......................................................................... 243
6.02 50 Hour Maintenance ............................................................................. 244
6.03 100 Hour Maintenance ........................................................................... 245
6.04 250 Hour Maintenance ........................................................................... 246
6.05 1000 Hour Maintenance.......................................................................... 247
6.06 2000 Hour Maintenance.......................................................................... 248
7�0 Troubleshooting �� 249
7.01 Engine Diagnostic Screen ....................................................................... 251
7.01.01 Engine Fault Codes .......................................................................... 253
7.02 Troubleshoot Engine Malfunctions ............................................................ 257

Contents
7.03 Troubleshoot Operations ......................................................................... 261

7.04 Troubleshoot Hydraulic Systems .............................................................. 263
7.05 Troubleshoot Batteries ........................................................................... 267
7.06 Troubleshoot Fluid Motors ....................................................................... 269
7.07 Troubleshoot Electrical Systems ............................................................... 271
8�0 Schematics �� 273
8.01 Lubrication Chart ................................................................................... 275
8.02 Hydraulic Schematics ............................................................................. 277
8.03 Electrical Schematics ............................................................................. 279
STANDARD WARRANTY �� 281
Order Parts�� 283
INDEX �� 285
NOTES �� 287


instructions, hydraulic and electrical schematics, parts assembly manuals and technical assistance
from your dealer or Roadtec Service Department.
DELIVERY DATE ______________

SERIAL NUMBER ______________
ENGINE NUMBER ______________
DEALER ______________
DEALER ADDRESS ______________
PHONE ______________
EQUIPMENT HOURS ______________
SERVICE MANAGER ______________


STANDARD WARRANTY
STANDARD WARRANTY
(“Products”) to be free from defects in workmanship and material, commencing with the date of initial startup
This limited
warranty remains in force for the above time period only if all Manufacturer’s operational and
warranty procedures are followed and recommended maintenance is performed� Manufacturer’s liability
than thirty days after the discovery of such alleged defect.
If, within such warranty period, any Product shall be proven to Manufacturer’s satisfaction to be defective, it
shall be repaired or replaced, at Manufacturer’s option. All defective parts or components must be returned to
end-user’s sole and exclusive remedy for breach of this limited warranty. Manufacturer may, at its sole discretion,
refund the purchase price of the defective Product in lieu of repairing or replacing it, provided the defective
authorized by Manufacturer. Labor for warranty repair will be paid under a formula determined by Manufacturer.
Wear parts including, but not limited to, conveyor lines, screed plates, cutter teeth, tooth holders, scraper blades,
track pads, tires and conveyor belts are warranted only if found to be defective at time of shipment, but are not
warranted for the warranty period against wear or abuse.
No warranty shall apply to Products which have been repaired or altered by others so as, in Manufacturer’s
judgment, to adversely affect the same or which shall have been subject to negligence, accident, abuse or
improper care, installation, maintenance, storage or other than normal use or service, during or after shipment.
No warranty shall apply to any used Product. No warranty shall apply to any Product adversely affected by being
used with any machinery, part or accessory not manufactured or authorized by Manufacturer. With respect
to machinery, parts or accessories which are furnished but not manufactured by Manufacturer, the warranty
does not provide any warranty as to such items.
Manufacturer does not warrant or represent that any Product furnished by it meets any federal, state or local
safety, environmental or electrical regulations. Manufacturer is wholly discharged from all liability under this
warranty in the event that the purchaser of the Product fails to pay for it in accordance with the applicable
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED

(EXCEPT WARRANTY OF TITLE), INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY
FROM COURSE OF DEALING OR USAGE OF TRADE, EACH OF WHICH IS EXPRESSLY DISCLAIMED�
MANUFACTURER SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES WHATSOEVER
WITH RESPECT TO MACHINERY, PARTS OR ACCESSORIES MANUFACTURED OR FURNISHED BY IT OR
ANY SERVICES, UNDERTAKINGS, ACTS OR OMISSIONS RELATING THERETO� IN NO EVENT SHALL
MANUFACTURER BE LIABLE TO ANY PARTY FOR ANY LOSS OF USE, REVENUE OR PROFIT, OR FOR ANY
CONSEQUENTIAL, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR PUNITIVE DAMAGES WHETHER
ARISING OUT OF BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE� THERE
ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF�
ROADTEC, INC�
Chattanooga, Tennessee

STANDARD WARRANTY

Proposition 65 Warning
WARNING: Breathing diesel engine exhaust exposes you to

chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
• Always start and operate the engine in a well-ventilated area.

• If in an enclosed area, vent the exhaust to the outside.
• Do not modify or tamper with the exhaust system.
• Do not idle the engine except as necessary.
For more information, go to www.P65warnings.ca.gov/diesel.
ADVERTENCIA: Respirar los gases del escape de motores a

diésel le expone a químicos conocidos por el Estado de California
como causantes de cáncer y defectos de nacimiento u otros
daños reproductivos.
• Siempre encienda y opere el motor en un área bien ventilada.

• Si es en un área cerrada, ventile el orificio del escape hacia el
exterior.
• No modifique ni altere el sistema de escape.
• No encienda el motor, excepto cuando sea necesario.
Para mayor información visite www.P65warnings.ca.gov/diesel.


Introduction
2.0 Introduction

Introduction

Introduction
2.01 Preface
The Roadtec brand is synonymous with innovation, Units of Measures
durability, top performance and customer support. Standard units for weight and measurements
For more than 34 years, Roadtec has been a used in this manual are listed as U.S. customary
market leader for mobile road building equipment units followed by their SI (metric) equivalents in
technologies. Asphalt Pavers are designed for parenthesis. For example, 12.67 ft. (3.86 m). Units
durability, maneuverability and traction. can be stated in words, such as quarts and inches.
Measures may be stated using abbreviations, such
This Manual as lbs. for pounds, or psi for pounds-per-square-
This manual serves as part of a set of manuals inch.
intended for the use of owners and operators.
This Manual provides information for the operation Reference Standards
and maintenance of the RP-170e Rubber Tire Reference standards are maintained for hazard
Asphalt Paver. Never remove the manuals from messages and other safety communications
the machine. Refer to the table of contents at established by the American National Standards
the front of this manual for a list of chapters and Institute (ANSI), the Occupational Safety and
sub-chapters. Locate the index at the back of this Health Administration (OSHA) and the American
manual for a list of alphabetical common words and Society of Mechanical Engineers (ASME).
phrases.
Copyright and Trademark
Roadtec recommends that all owners and operators Acknowledgments
become familiar with the manuals to maximize safe Copyright and Trademark acknowledgments
operations and long machine life. Follow all safety
warnings written in this Manual and all safety decals Power Solutions, Inc. MOBA is a trademark of
posted on machine. Read this manual in its entirety Mobile Automation GmbH. Shell is a trademark of
before attempting any operation or maintenance. Shell Oil Company. Roadtec is a trademark of Astec
This information is based on established procedures Industries, Inc.
to date. Refer to the most recent version of this
Manual as technical data and methods are subject Inspect the Machine
to change. Inspect machine loss or damage incurred
during transit. Check shipment against freight
The set consists of the Operation and Service bill or packing list. Notify transportation agent
Manual and the Parts Manual. The set is provided immediately if damage is found. Contact Roadtec
free of charge with the initial purchase of the
machine. Replacements are available for a fee to of operation for assistance with start-up, safe
cover printing and handling. The Parts Manual is operation and maintenance.
shipped as part of the technical CD- ROM or USB
located in the Operation and Service Manual. The Order parts and direct questions to:
Operation and Service Manual is stored on the CD/ Roadtec, Inc�
USB and is printed and shipped with the machine. 800 Manufacturers Road
PO Box 180515
Roadtec, Inc. and Astec Industries accepts Chattanooga, TN 37405-0600
no liabilities for losses, consequential losses, USA
disturbances, breakdowns, damages or claims
caused by the use of this Manual. 1�800�272�7100
1�423�265�0600
Fax 1�423�267�7104
www�roadtec�com

Introduction

Introduction
2.02 Description
The RP-180 Rubber Tire Asphalt Paver is an 8 specially-designed delta plate minimizes the gap
ft. wide rubber-tire asphalt paver with a compact against the conveyor and stops material from falling
wheelbase for greater maneuverability without forward and underneath the machine, preventing
sacrificed performance. The RP-180 is suitable for centerline segregation. Dual 12”x22” fabricated,
paving operations using windrow pickup machines offset front bogie wheels work to pre-compact
even on sharply inclined hills and wider paving soft grade material for faster, smoother mat
widths. Asphalt Pavers are useful for new road and development.
highway rehabilitation projects. The RP-180
offers an unmatched combination of power, The RP-180 is easy to maintenance. Dual fuel
traction, maneuverability and performance in fills are easy to reach. Electrical systems are lighted
the highway class of pavers. and accessible with clearly labeled systems that are
easy to troubleshoot. The full-size hydraulic engine
The RP-180 is simple to operate. Crew hood opens widely to allow easy access
members control operations from dual operator into the engine compartment. A manual hood lift
stations. Control panels are conveniently located feature is included for back-up. Hydraulic systems
on arm rests to allow full focus on the job at hand. are displayed on screen for easy diagnostics. Large
Operator seats hydraulically swing outward past hydraulic pumps are easily serviced and allow the
the machine for greater visibility, offering a clear entire circuit to run cool, prolonging pump life and
view back to augers, hoppers and the matching helping lower overall maintenance costs. Quick
line. Control screens are easily navigated using connect test ports on pumps can be connected while
one control switch. Flow gate settings are visually pressurized. Hydraulic filters are conveniently
displayed on screen for easy adjustments. A tilting located on top of the tank.
steering wheel and a single joystick control all
propel functions with ease. The RP-180 is built to last. The frame is
manufactured with the strength of A656 grade 80
The RP-180 saves time and money. The robust steel, yielding twice the strength as mid-strength
drive system is powered by a low emissions, steel frames used on similar machines in the
Cummins QSB 6.7 T4f 174 HP @ 2200 RPM. market. The side plates are 3/4” thick with a 2”+
Hoppers are engineered to optimize material flow front cross frame.
and prevent segregation. The narrow front apron
allows trucks to directly engage the hopper and The RP-180 is a heavy-duty machine
prevent material buildup. Tilting augers allow for especially designed for durability, efficiency
better material flow and are useful for supers, and high production. Roadtec Asphalt Pavers
partial passes and correcting mat defects. The 13” have become an essential tool for road builders all
conveyor opening height permits high levels of over the world who achieve smoothness specs and
material throughput. Chromium carbide floor plates long lasting roadways.
mean longer life and fewer replacement parts. The

Introduction

Introduction
2.03 Inspect a New Machine

Always inspect this equipment for evidence of consignee’s copies of the freight bill. The consignee
damage or missing parts before accepting and
unloading the machine. Never move equipment
claims for damage that occurred during transit to
inspection has been made. After the freight receipt the carrier for settlement.
Stop unpacking or moving the equipment if
was received in good condition. Therefore, a hidden damage is discovered after the carrier’s
thorough inspection is required using the check representative has gone. Contact the carrier’s local
list provided. Any and all damage that occurs to
the equipment and the components in transit is make an immediate inspection. Obtain a written
the responsibility of the carrier and not Roadtec. description and photos signed by the representative
Make clear photos of the damage and ask the driver for proof of claim.
to make a notation on both the carrier and the

Introduction

Introduction
2.04 Unit Nomenclature
Operator
Station
Engine
Compartment
Hopper
Screed Arm
Push Roller
Bogie Wheels
Tow Point Drive Wheel
Right Operator
Right Hopper Station
Wing
Left Hopper Left Operator

Wing Station

Introduction
Left Operator Right Operator

Station Station
Spreading
Auger

Introduction
2.05 Machine Dimensions
7 ft. 7 in. (285 cm)
16 ft. 3 in. (535 cm)
Dimension English Metric

Shipping Length (Tractor Only) 16 ft. 3 in. 535 cm
Shipping Height 11 ft. 5 in. 348 cm
Wheel Base 7 ft. 7 in. 285 cm
Shipping Width 8 ft. 2 in. 250 cm
Operating Width 10 ft. 6 in. 320 cm
Ground Clearance 6 in. 15.24 cm
Tractor Weight 29,280 lbs. 13, 344 kg

Introduction
10 ft. ¼ in. (306 cm)
10 ft. 1 in. (307 cm)

Introduction
2.06 Machine Specifications
Operational Specs English Metric

Working Speed Range 0-300 fpm 0-91 mpm
Travel Speed Range 0-10 mph 0-16 kph
Inside Turning Radius 30 in. 76 cm
Fluid Capacities
Fuel 81 gal. 306 L
Hydraulic Tank 66 gal. 250 L
DEF Tank 5 gal. 19 L
Engine Coolant 8.75 gal. 33 L
Engine Oil 18.5 qt. 17.5 L
Dimensions
Shipping Height 11 ft. 5 in. 348 cm
Shipping Width 8 ft. 10 in. 270 cm
Tractor Weight 29,280 lbs. 13, 344 kg
Truck Dumping Clearance 2 ft. 1 in. 63.5 cm
Hopper Length 6 ft. 6 in. 198 cm
Hopper Capacity 11.5 ton 10.4 mt
Standard Machine Weight 29,280 lbs. 13,344 kg
S-8 Screed 34,580 lbs. 15,685 kg
Carlson EZIV-8 35,630 lbs. 16,161 kg
Eagle 8 36,780 lbs. 16,683 kg

Introduction

Introduction
2.07 Engine Systems

Cummins QSB 6.7 T4f 174 HP @ 2200 RPM drives hydraulic propel pumps and auxiliary pumps.
Mounted behind operator station, accessible under machine. Fuel pump withdraws fuel from fuel tank.
pump. Automatic safety shut down for emergency situations. Electronic diagnostic gauge provides
instrumentation for tach/hour meter, oil pressure gauge, travel speed, voltage meter and engine fault
codes.
Turbo charger uses exhaust energy to pack more air into cylinders
combustion, fuel consumption and heat reduction; compensates to maintain combustion air density
for operating in higher altitudes. After-cooler cools pressurized intake air from turbo charger, allowing
greater air density for more complete fuel combustion. The engine will deliver full-rated power up to
8500 ft. (2590 m) altitude.
Refer to engine manual for more detailed information.
Engine Item Specification

Cummins QSB 6�7 T4f 173 HP @ 2200 RPM
Type In-Line
Stroke 4.21 x 4.88 in. (107 x 124 mm)
Displacement 408 cu. in. (6.7 L)
Power 174 HP (130 kW)
Idle Speed 2200 RPM
Engine Oil Type/Capacity SAE 15W40 API-CJ4/18.5 qt. (17.5 L)
Ambient Oil Temperature 0°F(-18°C) - 104°F(40°C)
Engine Cooling System
Capacity 8.75 gal. (33.1 L)
Engine Fuel
Type/Capacity Low Sulfur Diesel, 81 gal. (306 L)

Introduction

Introduction
2.08 Drive System

Propel system consists of two (2) industrial hydrostatic drive systems - one for each wheel drive. Each
system consists of a heavy-duty pump that drives a 2-speed hydraulic motor and gearbox assembly.
The hydraulic system powers left travel and right travel pumps.
Dual operator station controls allow for machine control from either side of machine.
Travel direction is controlled using a travel joystick. Machine steering is controlled by a steering wheel.
Drive Item Specification

MAIN DRIVE 2 speed
STEERING Steering Wheel, hydraulic swing
BRAKES Hydrodynamic, service & parking
SUSPENSION Rubber Tire
FRONT BOGIES dual 12 in. (356 mm) x 22 in. (559 mm)
TIRES
Front Tire Size
drive tires
Rear Tire Size (2) 16 in. x 24 in. (406 mm x 610 mm) Sand
Rib Drive Tires
SPEED
Traveling 0-10 MPH (16 KPH)
Paving 0-300 FPM (91 MPM)
HYDROSTATIC DRIVE
Drive Motors 2
Drive Pumps (2) variable displacement hydraulic pumps
Hydraulic Fluid 76 gal. (288 l)
Hydraulic Fluid Type Grade 46 Anti Wear Hydraulic Oil
Hydraulic Filters (5) canister, (2) 10-micron

Introduction

Introduction
2.09 Material Feed System
Flow Item Specification

Hopper 11.5-ton (10.4 mt) capacity,
equipped with hydraulically-folding
wings; Electrically-operated tunnel
gates provide rapid and convenient
Push Oscillating front push rollers control

Rollers truck position during material
unloading.
Auger Heavy-duty, ni-hard, 16 in. (406

mm) diameter, abrasion-resistant
lines.
Flow Gates
gates are controlled from operator
console and screed console; control

Introduction
Tow Points Indicator scales on right and left

side of paver indicate position of
right and left tow points; Screed
console switches or automatic
grade control system can be
used to adjust tow points. Always
position at zero reference before
paving operation begins.
Conveyor Variable speed, hydraulically-

System driven, 55 in. (1.4 m) width,
controllable from the operator’s
console and screed console, or can
be automatically controlled through
use of ultrasonic senors.
Fume Standard equipment for all Roadtec

Extraction pavers; designed to direct fumes
System and hot air away from the asphalt
tunnel and auger area and redirect
away from operators.
Screed Standard screeds for 8’ pavers

are vibratory, electrically-heated
screeds. Roadtec S-8, Carlson
EZIV-8, or the Roadtec Eagle 8.
Refer to screed operation and
service manual included in the
literature package for details.

Introduction
2.10 Electrical System

Comprised of two (2) 12-volt batteries connected at parallel locations and power the 24-volt CAN-bus
system. Electrical power can be shut off via battery quick disconnect switch.
The electronically-controlled engine on this machine provides the operator with the ability to
accurately monitor and control engine operation. The CPU will help safeguard against potential
circumstances that could result in damage to the engine by automatically shutting the engine down.
The CPU will generate fault codes to aid in the diagnosis of engine malfunctions and errors. Electrical
circuits are fuse-protected to help prevent damage. Fuses are located in the main electrical junction
box mounted inside the engine compartment.
Electrical Item Specification
BATTERY
Rating Heavy-duty
Volts 24-volt
Circuit breaker protection

ALTERNATOR
Rating 90-amp

Introduction

Introduction
2.11 Optional Equipment
Optional Equipment Specification

Screed Extensions Standard 8 ft. (2 m) electric heat
screed may be extended up to 24 ft.
(7.32 m) using optional 6” (15 cm),
12” (30 cm), 24” (60 cm) crown-
able and 26” (91 cm) extensions. All
extensions have replaceable wear
surfaces and are heated electrically by
internal heating elements.
Tunnel and Auger Tunnel and ni-hard auger extensions
Extensions are available from 1 ft. to 8 ft. with
the use of outboard auger hanger
bearing assemblies. These extensions
evenly distribute material feed
across the screed when using screed
extensions.
Hydraulic Strike-off Left and right 4 ft. hydraulic strike-

Extensions offs permit rapid changes in paving
width. Either side may be articulated
from positive 6.6% to negative 3.3%
crown or wedge courses by using
electric jack screws.
Electric Strike-Off Electric articulation provides for rapid
Articulation changes in slope of the right or left
hydraulic strike-off allowing changes
to crown or wedge courses by use of
electric jack screws.
Automatic Grade Control The screed elevation may be
automatically maintained with respect
to a reference point on one side of the
screed with the use of an automatic
control system. The opposite side
of the screed can be independently
controlled to a second reference grade
using a grade control.
Automatic Slope Control Slope may be automatically
maintained with respect to either the
right or the left reference grade of
the screed when an automatic slope
control is used with an automatic
grade control.

Introduction
Optional Equipment Specification

Averaging Ski 30 ft. (9.14 m) and 40 ft. (12.19
m) over the screed tubular or multi-
foot skis provide improved leveling
of existing surfaces by providing an
average reference grade for automatic
grade controls.
Truck Hitch Forward control of an unloading truck

can be obtained with the use of a
truck hitch. The truck hitch utilizes
hydraulically extending rollers that
engage the truck’s wheels to assist in
the forward movement of the truck
while paving.
Cut-Off Shoes 1 ft, 2 ft, 4 ft cut-off shoes are

available to reduce paving width.
Front Wheel Assist Add up to 36% additional draw bar

pull with the front wheel assist. Four
(4) 14”x22” (35.66 cm x 55.88 cm)
solid rubber steering tires provide
Paver Hopper Insert A paver hopper insert can be added

(for use with a material for use with a material transfer vehicle
transfer vehicle) and holds 15-20 tons. The hopper
insert is designed to provide a mass
slat conveyors.
Automatic Lubrication The automatic lubrications system

System will automatically lubricate various
components of the machine through a
series of grease lines.

Safety
3.0 Safety

Safety

Safety
3.01 Safety Features

EMERGENCY STOP BUTTONS
Locate red E-Stop Buttons on operator consoles
and ground control boxes.
Push Emergency Stop Buttons to immediately shut
down machine.
IMPORTANT!
Engine will not start until all E-Stop buttons are
reset to RUN. Turn E-Stop Button clockwise to
reset to RUN.
BEACON LIGHTS
Mounted on top of machine to warn personnel that
machine is in operation.
Activate beacon light when machine is started and
leave on until machine is shut down.
Locate Beacon Light Switch on operator console.
FUME EXTRACTION SYSTEM

Directs fumes and hot air away from the head
of material while paving. The Fume Extraction
system helps provide a cleaner work environment
for machine operators. Two blower unit inside the
engine compartment suction and then blow away
fumes from the head of material and out through a
specially designed exhaust.
BATTERY DISCONNECT SWITCH
Locate the battery disconnect switches in the

battery compartment.
Use the battery disconnect switches to shut off

power and prevent accidental engagement of
machine or components during maintenance or
service.

Safety
FIRE EXTINGUISHER
Located on the operator’s station.
Extinguishant - Ammonium phosphate base
REVERSE ALARM
Sounds an alarm when machine is moving in a

reverse direction.
HORN
Locate the horn on the operator console. Push up

to sound.
HAZARD ALERT SIGNS

Locate all hazard alert and warning decals and
signs on the machine. Follow all instructions.
Replace any missing or damaged decals
immediately.

Safety
3.01.01 Machine Danger Zones

Keep away from danger zones during operation and transport of machine.
Stay clear of tires, rear of machine, front of machine, hopper and auger area. Stay behind rails on
operator station. Stay clear of screed.
Only authorized personnel who perform maintenance and service are allowed to enter danger zones.
Ensure machine is shut down and locked down before entering danger zones.
! !
!

Safety

Safety
3.02 Safety Requirements

Most operation and maintenance-related accidents are caused by failure to follow safety rules.
Accidents can be prevented by recognizing hazardous situations before they occur.
Safety is a FIRST priority when operating heavy equipment and its componentry. Practice established
safety procedures when installing, operating or servicing this equipment. These safety warnings are
not meant to cover every possible situation that may occur. The manufacturer has no direct control
over application, operation, inspection or maintenance. It is the machine operator’s responsibility
to practice safety�
safety practices. Study the most recently updated version of the machine Manual before operating or
servicing any equipment.
Safety features include emergency stop buttons. All E-stop buttons must be disengaged, or pulled
out before engine will start. Battery Disconnect Switches must be on and parking brakes set to ON in
order for engine to start.
Symbols, signal words, hazard alert decals and pictograms are used throughout this Manual to
emphasize potential hazards and indicate the relative level of severity.
Death or serious injury WILL result

if situation is not avoided
! DANGER
Death or serious injury COULD
result if situation is not avoided
! WARNING
MINOR OR MODERATE injury
could result if situation is not
! CAUTION avoided
Alert for practices not related to

physical injury
NOTICE

Safety
3.03 Wear Personal Protective Equipment (PPE)

▶ Hard Hat ▶
▶ Hearing protection ▶ Safety glasses or goggles
▶ Safety Shoes ▶ Face shield
▶ Heavy gloves ▶ Wet weather gear
! WARNING
Protect your body!
Wear ALL required personal protective equipment.
W-1001
3.04 Commit to 100% Safety

ALWAYS!
▶
▶ Use safety checklists.
▶ Take safety training programs.
▶
▶ Understand how fatigue, carelessness, drugs, alcohol, lack of training and overload can cause
accidents.
▶ Encourage others to follow safety practices.
NOTICE
Safety is up to you!
Study this safety section and the
manufacturer’s manuals before
operating or servicing this machine.
N-1001

Safety
3.05 Learn Safety
1� Study manufacturer’s operation and service manual. Learn machine capabilities and limitations.
2� Learn controls, indicators and safety features. The machine will alert you to dangerous conditions
such as high temperature or low pressure.
3� Understand machine safety devices and instructions. Keep safety signs and decals in good condition.
! DANGER
Avoid occupational hazards!
NEVER operate machines with missing or broken
guards, rails or safety devices.
NEVER remove or disable safety devices.
D-1001
3.06 Know the Rules
▶ Check with supervisors or safety coordinators before operating this machine. Learn all the rules you
will be expected to follow.
▶ Check for local, state/provincial laws that apply to this machine. The Occupational Safety and Health
Administration (OSHA) enforces federal laws within the U.S. that apply to safe operation, application
and maintenance of equipment on a work site.
! CAUTION
NEVER use drugs or alcohol while operating machine.
NEVER allow anyone with impaired coordination or
decreased alertness to operate machine.
C-1002

Safety
3.07 Perform Quality Inspections

ALWAYS!
▶ Conduct equipment inspections before operating machine.
▶
▶ Keep all parts properly installed and in good working condition.
▶ Follow daily maintenance schedules.
3.08 Know the Machine
▶ Alarms ▶ Decals
▶ Guards ▶ Covers
▶ Fire Extinguisher ▶ Lights
▶ Shields ▶ Hand Rails
▶ Horn ▶ First Aid Kit
! CAUTION
NEVER
machine.
NEVER operate machinery known or suspected to
be malfunctioning.
C-1003
ALWAYS!
▶ Understand hazard zones created by heavy equipment in operation.
▶ Stay out of machine danger zones.
▶ Be familiar with all pedals, controls, mirror ranges and safety devices.
▶ Know blind spots and machine height clearances.
▶ Read and understand all machine operations, decals and safety signs.
▶ Know what to do if machine becomes disabled.

Safety
3.09 Prevent Fires

ALWAYS!
▶ Refuel in ventilated areas.

▶ Replace fuel cap after refueling.
▶ Wipe rails, walkways, controls, foot pedals and hand levers clean of oil and grease.
▶
▶
▶ Replace worn hoses, frayed wires and broken cables.
! WARNING
NEVER
NEVER dispose of cigarettes, cigars or matches near
machines.
NEVER
W-1012
3.10 Know the Job Site

ALWAYS!
▶ Know ground surface load limits.

▶
▶ Check bridge and road conditions.
▶ Look for pipes, gas lines, manholes and hidden rails.
▶
▶ Avoid curbs, sidewalks and driveways.
▶ Learn emergency stop procedures.
! WARNING
NEVER operate this machine on sloped,
muddy or soft surfaces.
NEVER exceed safe travel speeds.
W-1013

Safety
3.11 Load/Unload Safely

ALWAYS!
▶ Use extreme caution when loading or unloading machinery.

▶ Ensure ramp capacity exceeds machine weight.
▶ Load and unload on level surfaces.
▶ Keep personnel back at least 16 ft. (5 m) from machine.
! CAUTION
Avoid crushing hazards!
NEVER load or unload a machine alone.
NEVER use tie downs for towing, pulling or
any other purpose. This machine was not
designed for towing vehicles.
C-1004
3.12 Mount and Start Safely

ALWAYS!
▶ Follow manufacturer’s start-up procedures.

▶
▶ Wipe boots clean before mounting.
▶ Maintain three-point contact with ladders.
▶ Start machine only from operator’s station.
▶ Check emergency stop buttons.
▶ Clear work areas and walkways of trash, ice, debris, oil, grease, supplies and tools.

Safety
3.13 Focus on Safety

ALWAYS!
▶ Ensure engine is working properly. Test steering and listen for unusual noises.
▶ Use caution when operating machine near ditches or ruts.
▶ Stay in designated areas and behind safety rails when operating machine.
▶ Understand gauge, instruments and warning lights.
▶ Keep back from running machine and all its rotating components.
▶ Beep horn to warn bystanders before moving machine.
! WARNING
Avoid sudden machine movement hazards!
NEVER apply parking brake when machine
is in motion.
NEVER climb on or off a machine during
operation.
W-1014
3.14 Practice Ground Operation Safety

ALWAYS!
▶ Stay behind guard rails, safety rails and barriers.

▶ Use extreme caution when working near moving machinery.
▶ Stay clear of areas between machines.
▶ Keep personnel clear of machine and screed about to be started or in operation.
▶ Stay clear of automatic system components and sensors.
! WARNING
Avoid crushing and entanglement hazards!
NEVER remove material from moving parts
while machine is in operation.
NEVER stand in between moving machines
or near moving machine parts.
NEVER wear loose clothing, long hair or
accessories when operating this machine.
W-1015

Safety
3.15 Be Safe Around Fumes

ALWAYS!
▶
▶ Read all Material Safety Data Sheets (MSDS) listed with product manufacturers for a list of substances
3.16 Work Safely

ALWAYS!
▶ Keep all body parts clear of moving components.

▶ Ensure machine has full clearance. Stay clear of tires and screed.
▶ Maintain safe speeds. Slow down when making sharp turns.
▶ Monitor machine-to-machine speed/distance to prevent collision.
▶ Set brake switch safety cover when leaving operator’s station to prevent accidental application.
▶ Use E-stops to shut machine down immediately. Locate red pull stops at operator console and ground
boxes. Engine will start when E-stop buttons are reset to RUN.
! DANGER
Avoid serious injuries or death!
NEVER service machine while engine is
running.
NEVER stand near or beneath machine,
screed or any moving machine component.
Avoid falling hazards!
NEVER climb on or off a moving machine.
NEVER allow riders or tolerate horseplay.
D-1021

Safety
3.17 Work Safely At Night

ALWAYS!
▶ Understand and communicate plans for the hazards of nighttime operation.

▶
▶ Check visibility of gauges and controls.
▶ Ensure machine is equipped with working hazard lights.
▶ Pay special attention to work zones and personnel at all times.
▶
▶ Be aware of fatigue during nighttime operations.
! CAUTION
Avoid nighttime hazards!
NEVER leave assigned work zones.
NEVER rely on mirrors for visibility when working at
night - use direct line of sight.
C-1005
3.18 Park Safely

ALWAYS!
▶ Follow manufacturer’s shutdown procedure.

▶
▶ Leave parking clearance between vehicles and machines.
▶ Remove keys and lock battery switches.
▶ Dismount using 3-point contact with steps and rails.
▶
NOTICE
Avoid accidental engine application!
NEVER leave machine overnight until
parking brakes are set, battery disconnects
are locked, master switches are off and
tires are blocked.
N-1028

Safety
3.19 Maintenance Safely

ALWAYS!
▶ Follow manufacturer’s service manual.

▶
▶ Stop engine and disconnect batteries.
▶ Use proper tools in good working condition.
▶ Support equipment properly when working beneath.
▶ Allow machine to cool before performing maintenance or repair.
! WARNING
Avoid serious injuries and death!
NEVER perform service or repair until
completing machine shut down and
lockout/tag-out procedures.
W-1016
3.20 Take Precautions
ALWAYS!
▶ Disconnect battery and engine electronics before servicing machine.

▶ Stand to side of radiator when removing cap. Ensure radiator is cooled.
▶ Turn off machine before servicing conveyor.
▶ Follow manufacturer’s lube charts.
▶ Turn off engine before using the manual hand pump to lower and raise hood.
▶ Secure machine to the towing vehicle or chock wheels before releasing brakes and opening HPRV
valves.
▶ Use extreme caution when working beneath machine.

Safety
3.21 Service Battery Safely

ALWAYS!
▶ Disconnect batteries using battery isolation switch before performing maintenance or repairs.
▶
▶
▶ Avoid touching battery acid or electrolyte.
▶ Wear protective clothing and safety goggles when servicing batteries.
! DANGER
Avoid explosion hazards!
NEVER attempt to jump start or
charge a frozen battery.
NEVER weld on machine without
disconnecting batteries.
D-1014
3.22 Safely Service Electric Systems
ALWAYS!
▶ Follow manufacturer’s operation and service procedures for servicing electric systems.
▶
▶ Verify voltage with testing tool.
▶ Never open electrical enclosures while generator is running.
▶ Replace covers before operating machine.
▶ Always disconnect engine electronics with the engine electronics disconnect switch before servicing or
welding on this machine.
▶ Always ensure battery disconnect switches are disconnected before performing service or maintenance
or welding on the machine.
▶ Ensure welder is grounded close to the location of welding. Never ground the welder to an electric box
or to the engine. Disconnect the electrical box or controller before welding when the welding to be
performed is near an electrical box or remote-mounted controller.
! DANGER
Avoid electric shock hazards!
NEVER perform maintenance or
repairs to electric system until
engine is turned off and batteries
are disconnected using the battery
isolation switch.
D-1015

Safety
3.23 Safely Service Hydraulic Systems

ALWAYS!
▶
▶
▶
▶
▶
▶
! WARNING
Avoid pressure explosion and burn
hazards!
NEVER weld or cut on fuel tank or
hydraulic tank.
NEVER allow oil level to fall below
indicator line.
NEVER use hands to locate leaks. Use
cardboard.
W-1017
3.24 Material Safety Data Sheets (MSDS)
▶ Request MSDS sheets from manufacturers to understand potential health hazards associated with
substances used on this machine, including gear oil, diesel engine oil, antifreeze, coolant, hydraulic oil
and diesel fuel.
3.25 Safety First
▶ Safety is up to you!
▶ You can prevent serious injury and death.
▶ Give 100% focus to safety at all times.

Safety
3.26 Hazard Decals

Following decal warning is critical for safe operations.
death.
Replace worn or missing hazard alert decals immediately.
Ensure anyone working on or around this machine is familiar with these warnings.
Safety is up to operators and crew members.
Locate, understand and follow every safety decal on machine.
Caution - Pinch point area. Keep clear when

Do not step here.
Warning - Pinch point area. Keep clear when


Safety
Warning - Explosion hazard. Never use starting
Warning - Always disconnect batteries using

battery isolation/disconnect switches before
performing maintenance or welding on machine.
Caution- Clean fuel, lubricant and hydraulic oil from

walkways.

Safety
Warning - Read and understand the operator’s

manual before operating or servicing this machine.
Caution - No smoking within 50 feet during

machine fueling or wash-down.

Safety
Caution - Never get on or off of a moving machine.
Danger - Never stand in hopper when engine is

running.
Caution - Stand clear of material discharge area.

Operation
4.0 Operation

Operation

Operation
4.01 Principles of Operation

Roadtec Pavers are used to create and lay a high-
density, smooth asphalt roadway for interstates,
highway, runways, roads and parking lots.
The paver tractor receives material, then delivers

the material in front of a screed attachment,
which the tractor tows forward. The material is
leveled and smoothed by the screed.
Hot asphalt mix is delivered to the paver hopper via

dump trucks or haul trucks. A windrow machine can
also be used to suction material from the roadway
and deliver material to the paver.
The haul truck is pushed forward by the forward-

moving paver via push rollers that contact the
haul truck rear tires as it delivers the load in order
to maintain continuous paving. Pavers can be
designed as rubber tire or rubber tracks. Steel track
pavers and gravity-fed pavers are two other types
of asphalt road pavers offered by Roadtec.
The RP-170e Rubber Tire Asphalt Paver is capable

of laying a mat with widths ranging from 6 ft. to 24
ft. The paver can be pre-programmed for control
depth are controlled with feed control dials and

screed adjustments�
Augers in the paver hopper keep material mixed
as two separately-controlled slat conveyors transfer
hot mix asphalt to spreading augers at the end
of the tractor where the tractor meets the screed
attachment. The spreading auger delivers material
to the road surface.

Operation
Pavers utilize a screed attachment to lay the
utilize heated elements to smoothly iron the surface

of the mat.
Right and left side arms connect to the screed at

the pivot points and to the tractor at the tow
points enabling the screed to self-level as it is
pulled along the mat surface, independent of the
tractor.
The describes the

displacement of the screed vertically as it rises and
falls on the material surface. Eventually, the screed
travels on a plan that is parallel to the line of pull�
Mat thickness is controlled by the rise and fall of
the screed.
The material can be controlled using
adjustments. Two independently controlled

conveyors (left and right side) each contain a slat
conveyor and auger to move material through the
conveyor tunnel.
“head of material” in front of the screed must

be maintained consistently and evenly in order to
produce a uniform mat.

Operation
in order to smooth out the mat surface. The
or negative crown. The screed crown can be

adjusted to have a positive crown, which is a
slightly inverted V-shape. Both crown adjustments
work to lay a mat for water drainage requirements.
Burners on the bottom of the screed are heated

during the pre-operational stages to be the same
temperature as the hot mix in order to prevent
material from sticking to the screed. The screed
bottom must be kept clean in order to prevent a
low quality mat surface.
Screeds can employ a strike-off plate, which

mounts in the bottom front of the screed and cuts
material off as the screed passes over. In order
to lay wider mats, screed extensions or strike-
off extensions can be installed. Cut-off shoes
can be installed on the screed to reduce paving
width for narrowing roadways. Vibrators employ
slight movement to the compaction of the mix as
the screed bottom irons over it, keeping the mix
distributed instead of sticking together or adhering
to the screed bottom. Material is then smoothed
and compacted by the screed rollers.

Operation

Operation
4.02 Operator Station
Dual operator stations enable greater

visibility during the paving operation. Control
machine with Left and Right Hand Controls,
steering wheel and center control box.
Digital Control Screen displays gauges,

engine information and system fault codes.
Ground Control Panels on either side of he

screed control cutter system, drum, and end
slides.

Operation
4.03 Left Seat/Left Side, Right Seat/Right Side Operator Console
4 10
11
12

Operation
1� Conveyor Switches
Activates or deactivates left and right side slat conveyors.
Activate - Push up
Deactivate - Push down
2� Feed System Switches
Activates left and right side material feed system.
MANUAL - Feed system runs continuously.
AUTO - Feed System automatically stops when sonic sensors detect that the head of material is too
thick.
STOP - Feed System will deactivate the feed system
3� Auger Switch
Raises or lowers the augers.
NOTE: Always completely raise the augers when loading or traveling the machine to ensure
clearance height.
RAISE - Push up
LOWER - Push down
4� Hopper Switch
Raises or lowers hopper wings for material height
RAISE - Push up
LOWER - Push down
5� Screed Extensions Switches
Extends or retracts left and right side screed extensions.
EXTEND LEFT SIDE - Push left
RETRACT LEFT SIDE - Push right
EXTEND RIGHT SIDE - Push right
RETRACT RIGHT SIDE - Push left
6� Flow Gate Switches
spreading augers.
RAISE - Push up
LOWER - Push down
7� Screed Assist Switch or Screed Boost Switch (OPTIONAL)
Screed Assist - designed for rear-mounted extension and provides a means to offset the weight of
an extendible screed when paving narrow lanes.
Screed Assist is turned on during paver operations.
NOTE: Never turn Screed Assist off during paving operation to prevent bumps in the mat.
Screed Boost - designed for front-mounted extension screeds. Screed Boost will cause the screed
Screed Boost will pressurize the bottom of the screed lift
cylinders and prevent the screed from dropping when the paver stops.
ACTIVATE - Push up
DEACTIVATE - Push down
8� Platform Slide Switch
Activates the slide platform feature to the left or right to provide operator visibility.
SLIDE LEFT - Push left
SLIDE RIGHT - Push right

Operation
9� Horn Switch
Sounds the horn.
ACTIVATE - Push up
10� Screed Lift Switch
Raises or lowers screed. Float allows screed to be automatically adjusted by automatic grade
controls. Hold will maintain screed in a rigid position. Lift will raise screed.
LIFT - Press up
HOLD - Press center
FLOAT - Press down
11� Truck Hitch Switch (OPTIONAL)
Connects or disconnect dump truck and paver.
CONNECT - Press left
DISCONNECT - Press right
12� Vibration
Activates or deactivates screed vibrators.
ACTIVATE - Press up
DEACTIVATE - Press down

Operation

Operation

Operation
4.04 Left Seat/Right Side, Right Seat/Left Side Operator Console
1 9
10
3
5 11
7 12
13
14
8

Operation
1� Travel Joystick
Engages forward or reverse machine movement.
FORWARD - Push up
NEUTRAL - Push center
REVERSE - Push down
2� Throttle Switch
Increases and decreases engine speed (rpm). Automatic mode will automatically invoke full
throttle when machine is in forward paving mode and low throttle when in neutral.
HIGH - Push up
AUTO - Push center
LOW - Push down
3� Differential Lock Switch
Activates the differential lock circuit when positive traction is required. Useful when road conditions
are wet and one wheel loses traction. Both rear wheels rotate at the same speed regardless of
traction.
NOTE: Never activate differential lock switch when turning machine sharply.
ACTIVATE - Push up
4� Main Power Switch
Engage the engine. Push engine ON button for 3-5 seconds, then push switch to start position.
NOTE: All E-stop buttons must be in the run position before engine will start.
ACTIVATE IGNITION - Push center
START ENGINE - Push up
STOP ENGINE - Push down
5� Regenerate Switch
Controls the Diesel Particulate Filter (DPF) regeneration system. Spring-loaded switch remains in
center position until pressed up or down. Center position will automatically regenerate engine DPF
system when necessary.
NOTE: Never stop DPF regeneration unless machine is located in an area that would result in unsafe
conditions. Regenerate immediately when possible if regen is forcibly stopped.
REGENERATE IMMEDIATELY - Push up
AUTOMATICALLY REGENERATE - Center position
MOMENTARILY STOP REGENERATION - Push down
6� Brake Switch
Stops machine motion.
ACTIVATE - Push up
7� Range Switch
Travel range is used when moving machine from one location to another. Pave is selected for paving
operation. FWA if selected for front wheel assist.
NOTE: Never travel paver in high speed with hopper loaded. Never travel or pave on grades of 6%
or greater. Never change speeds when paver is in motion.
TRAVEL - Push up
PAVE - Push center
FORWARD WHEEL ASSIST - Push down

Operation
8� Hood Switch
Raises or lowers engine compartment hood for service procedures.
NOTE: Always use support pin when hood is raised before working under hood.
RAISE - Push up
LOWER - Push down
9� Emergency Stop Button
Press to immediately shut down the engine in case of emergency.
NOTE: Engine will not restart until all E-stop buttons have been disengaged.
ACTIVATE - Push down
DEACTIVATE - Pull up
10� Steer Assist Switch
Activates steering assist feature that will create tighter turning radius when steering paver to the
left or right. As paver makes a left turn and steer assist is pushed left, the right drive motor de-
rates allowing the motor to push the paver through the turn with a tighter radius. The same is true
for a right turn/right steer assist switch.
LEFT TURN - Push left
RIGHT TURN - Push right
11� Paver Speed Dial
Increases or decreases forward speed while paver is in travel mode.
INCREASE SPEED - Turn left
DECREASE SPEED - Turn right
12� Console Select Switch
Used to alternate between right and left hand operator’s console.
NOTE: Only one console at a time can be used for machine control.
LEFT CONSOLE - Push left
RIGHT CONSOLE - Push right
13� Strobe Switch
Activates the strobe light to alert persons in and around the work zone of machine operations.
NOTE: Always activate strobe when operating or transporting machine.
ACTIVATE - Push up
14� Lights Switch
Activates work lights for nighttime operations.
NOTE: Always activate work lights when operating or transporting machine.
ACTIVATE - Push up

Operation
4.05 Machine Control Screen

Located on the operators station near right and left side steering wheels
Displays service screens, operator screens, calibration screens and engine diagnostic screens.
Access Input/Output Monitoring Screens from Left Operator’s Display. Calibrate Wheels from Right
Operator’s Display.
Digital Display Screen

Operation
4.05.01 Main Screen

Main Screen
The Main Screen Display 1 shows a quadrant of customizable monitors. Shown here are Engine
Hours, Water Temp, Boost Pressure, and Torque.
Press 3 (right arrow) to advance to Main Screen Display 2 to view the second quadrant of
customizable monitors.
Engine Regeneration Status will display on center of Roadtec icon. See Engine Regen screens at
the end of this section�

Operation
4.05.02 Configure Main Display 1 and Display 2 Screens

Configure Main Screen Displays
Press button 4 (wrench icon) to advance to the Menu Options Screen.
advance to the options.

Press 2 (green plus) to toggle through the quadrants.
Press button 3 (paper and pencil) to select quadrant, then press button 2 to toggle options for that
quadrant.
Press 4 (disk) to save the options.
Press EXIT to return to the Main Screen

Operation
4.05.03 Menu Options

Menu Options
Press 4 (wrench icon) to advance to the Menu Options Screen.

Press 2 or 3 to scroll up and down through the options. Option selections will highlight green.
Press 4 to select option.
See Section 8.01 for Request Fault Codes, Clear Stored Codes and Clear Active Codes.
Press EXIT to return to the Main Screen.

Operation
4.05.04 Set Up Screed Boost

Set Up Screed Boost
Choose Screed Boost Set Up from Menu Options Screen, and press 4 (wrench).
Press 2 (up arrow) to increase delay in seconds.
Press 3 (down arrow) to decrease delay in seconds.

Operation
4.05.05 Set Units of Measure

Set Units of Measure
Choose Imperial or Metric form Menu Options Screen, and press 4 (green check) to change units of
measure displayed on machine controls. Both Standard Units and H1 Motors can only be accessed
from the Right Operator Control display.

Operation
4.05.06 Display Hydraulic Pressures

Display Hydraulic Pressures
Choose Display Hydraulic Pressures to navigate to the screen that displays the pressures for all
pumps, including left propel, left propel charge, left conveyor, left conveyor charge, auxiliary, right

Operation
4.05.07 Set Button Backlight

Set Button Backlight
Choose Button Backlight from the Menu Options, and press button 4 (wrench) to turn the Button
Backlights ON or OFF.

Operation
4.05.08 Set Screen Backlight

Set Screen Backlight
Choose Screen Backlight from the Menu Options, and press button 4 (wrench) to turn the Screen
Backlights ON or OFF.
Adjust the dimness or brightness in increments of 10% with the down or up arrow.
Press EXIT twice to return to the Main Screen.

Operation
4.05.09 Troubleshooting Screens

Troubleshooting Screens
Choose Troubleshooting Screens to access the Troubleshooting Screens, and press button 4
(wrench).
The warning page appears to caution that machine movement is possible. Please read the
Operation and Service Manual before using the screens to perform maintenance or repair. Only
to enter the Troubleshooting Screens.


Operation
4.05.10 Troubleshooting Screens - ROC Upper Left Screen

Troubleshooting Screens - ROC Upper Left Screen
Press the ENTER button from the Troubleshooting Screens Warning screen to access the ROC Upper
Left Screen.
Monitor the switches for Left and Right Conveyor, Left and Right Feed System, Hopper, Platform,
Horn, Auger, and Screed.

Operation
4.05.11 Troubleshooting Screens - ROC Lower Left Screen

Troubleshooting Screens - ROC Lower Left Screen
Press button 4 (right arrow) from the ROC Upper Left screen to access the ROC Lower Left Screen.
Monitor the switches for Left and Right Screed extensions, Left and Right Flowgate, Screed Boost/
Assist, and Vibrator.

Operation
4.05.12 Troubleshooting Screens - ROC Upper Right Screen

Troubleshooting Screens - ROC Upper Right Screen
Press button 4 (right arrow) from the ROC Lower Left screen to access the ROC Upper Right Screen.
Monitor the switches for the Joystick, E-Stop, Differential Lock, Throttle, and Steer Assist.

Operation
4.05.13 Troubleshooting Screens - ROC Lower Right Screen

Troubleshooting Screens - ROC Lower Right Screen
Press button 4 (right arrow) from the ROC Upper Right screen to access the ROC Lower Right
Screen.
Monitor the switches for the Regenerate, Range, Front Wheel Assist, Hood, Main Power, Paver
Speed, Brake, and Foot Brake, Strobe Lights, and Lights.

Operation
4.05.14 Troubleshooting Screens - ROM and LOM Output Module 1

Troubleshooting Screens - ROM and LOM Output Module 1
Press button 4 (right arrow) from the ROC Lower Right Screen to access ROM Output Module 1 and
LOM Output Module 1.
Screed Float, Screed Lift, Screed Lower, Right Auger Raise, Manual Left Conveyor, and Manual Right
Conveyor) and Connector B (Right Auger Lower, Left Auger Raise, Left Auger Lower, Left Cons Pivot
In, Left Cons Pivot Out, Right Cons Pivot In, Right Cons Pivot Out, Right Conveyor Bypass, and Right
Auger Bypass.
Speed Shift, Truck Hitch In, Truck Hitch Out), and Connector B (Left Tunnel Extension, Left Tunnel
Retract, Right Tunnel Extension, Right Tunnel Retract, BackUp Alarm, Right Turn Signal, Brakelights,
Left Turn Signal, Left Auger Bypass).

Operation
4.05.15 Troubleshooting Screens - ROM and LOM Output Module 2

Troubleshooting Screens - ROM and LOM Output Module 2
Press button 3 (right arrow) from the ROM Output Module 1 to access ROM Output Module 2.
Monitor the ROM Output Module 2 for Connector A (Left FG Raise, Left FG Lower, Right FG Raise,
Right FG Lower, Start Assist, Differential Lock, Left Conveyor Rev. 0) and Connector B (Right
Conveyor Rev. 0, Fan Pump 0, Left Propel Pump Forward 0, Left Propel Pump Rev. 0, Right Propel
Pump Forward 0, Right Propel Pump Rev. 0, Screed Boost Check Valve).
Monitor the LOM Output Module 2 for Connector A (Screed Boost Assist, Generator, Auxiliary Dump
Valve, Hopper Raise, Hopper Lower, Front Wheel Assist), and Connector B (Front Wheel Assist Soft
Shift, Track Tension, L C/V Bypass Stop, Dump Light Green, Dump Light Yellow, Dump Light Red,
Manual Left Conveyor and Manual Right Conveyor).

Operation
4.05.16 Troubleshooting Screens - MC50-155 Input/Output 1 Status

Troubleshooting Screens - MC50-155 Input/Output 1 Status
Press button 3 (right arrow) from the ROM Output Module 2 screen to access the MC50-155 Input/
Output 1 Status screen.
forward propel pressure, trans right propel charge pressure, trans left propel charge pressure, trans
auxiliary pressure, trans right conveyor forward pressure, trans left conveyor forward pressure, right
conveyor charge pressure, left conveyor charge pressure, trans fuel sender, CAC temp sender, and
hydraulic oil temp.

Operation
4.05.17 Troubleshooting Screens - MC50-155 Input/Output 2 Status

Troubleshooting Screens - MC50-155 Input/Output 2 Status
Press button 3 (right arrow) from the MC50-155 Input/Output 1 screen to access the MC50-155
Input/Output 2 Status screen.
PPU, left propel PPU, and horn relay.


Operation
4.05.18 Troubleshooting Screens - CAN Network Health

Troubleshooting Screens - CAN Network Health
Press button 3 (right arrow) from the MC50-155 Input/Output 2 screen to access the CAN Network
Health screen.
Monitor LOC_DM430 (left operator digital screen), ROC_DM340 (right operator digital screen), left
input module, right input module, left screen control, right screed control, Left LSC-MC024 control,
right LSC-MC024 control, right screed DM-430 (digital display), left screed DM-430 (digital display),
Main junction box, option-in module (CAN1), LOM Module 1 (CAN1), LOM Module 2 (Can 1), ROM
Module 1 (CAN2), ROM Module 2 (Can2), and Joystick CAN0.

Operation
4.05.19 Troubleshooting Screens - H1 Motors

Troubleshooting Screens - H1 Motors
Choose H1 Motors from the Menu Options Screen (if machine is so equipped) and press button 4
(wrench) to toggle H1 Motor to YES.
The processor uses different calculations based this motor type.
If H1 is not selected, then the feet-per-minute calculations for example will not display accurately.

Operation
4.05.20 SCR Exhaust System Cleaning (Regen) Modes

SCR Exhaust Cleaning System (Regen) automatically initiates during operations.
Inhibit or Force (Non-Mission) Regen — for use only when inhibiting cleaning would prevent safety
risks.
Control Display - Main Screen
Exhaust Cleaning
Lamps

Operation
4.05.20.01 SCR Engine Exhaust System Cleaning (Regen)
operations and cleaner air quality.

Elevated temperatures clean Diesel Exhaust Fluid (DEF) deposits from the Decomposition Reactor
Tube (DRT) and the Selective Catalyst Reduction (SCR).
Refer to Engine Manufacturer’s Manual for more information.
After-Treatment System

Operation
1. Automatic
2. Non-Mission
3. Inhibited
Minimal operator interaction is needed when a Non-Mission Cleaning Event is required.
Control Display - Main Screen
Exhaust Cleaning
Lamps
Exhaust System Lamp Behavior

Operation
Lamp Functions Description Machine Behavior Operator Action

High Exhaust Automatic - Indicates Exhaust temperatures during No operator action
System exhaust system temperature is cleaning event may reach required� Continue
Temperature elevated. 1000 – 1100° F. operations as normal�
(HEST) Lamp ON Cleaning automatically initiated No engine speed or torque
at preset time increments decrease. DANGER!
NORMAL during machine operation every Any throttle change stops Keep engine exhaust pipe
60-80 hours. Cycles take 15-30 automatic cleaning event. outlet away from persons
T1 Level (60- 80 hrs� since minutes to complete.
last cleaning event) Engine speed must be > 1500
during high temperature
rpm. Engine exhaust temp must
cycles.
be > 572° F.
Exhaust System Indicates Automatic or Non- Automatic FC 2777 Automated

Cleaning Lamp Mission cleaning. FC 2777 Cleaning: No operator
No engine speed or torque action required�
ON Automatic - Cleaning initiated
during machine operation decrease.
FC 3753 Non-Mission
at T2+10 hours when prior Non-Mission
Cleaning Required: Stop
HEST Lamp ON automatic cleaning event did FC 3753 machine and initiate SCR
not complete. Machine is stationary during Cleaning� See Section
Non-Mission – Illuminates at cleaning. Engine speed 3�07�08�02
T2 + 5 hours. Cleaning should decreases by 25%. Throttle
INFREQUENT be initiated by operator as soon to 1000 rpm. Maintains speed DANGER!
Automatic ON as possible. for 30-45 minutes. Keep engine exhaust pipe
T2 Level (T1 + 10 hours) Any throttle change will stop outlet away from persons
Engine speed is > 1500 rpm. auto cleaning event.
Non-Mission required ON -
Exhaust temp > 572° F. Automatic cleaning resumes
T2 Level + 5 hours; during high temperature
when conditions are met.
Non-Mission in progress cycles.
FLASH
Exhaust System Near Critical System Status Near Critical Status Stop machine and perform
Cleaning Lamp – Indicates T2 + 10 hours since FC 3714 Non-Mission Exhaust
ON last cleaning event. Engine speed and torque start Cleaning�
See Section 3�07�08�02
Critical System Status –
Indicates T3+ 5 hours since last Critical Status
cleaning event. DANGER!
Check Engine FC 4863 Park machine with
Lamp ON exhaust pipe outlet away
reduced and torque rate from all persons and any
decreased by 25%.
VERY INFREQUENT surfaces during high
Near Critical temperature cycles.
T3 Level (T2 + 10 hours)
Critical
T3 Level + 5 hours
Stop Engine Lamp Stop Engine - Indicates red Engine power limited to idle. Shut down engine as
ON level warning. Further machine soon as possible� Contact
operation can result in damage Cummins�
to exhaust system. CAUTION! Failure to shut
down engine will damage
AVOIDABLE
exhaust system.
T3 Level + 10 hours
Exhaust System Inhibited - Indicates exhaust No engine or torque decrease. CAUTION!
Cleaning Inhibit cleaning system is OFF,
Lamp ON preventing automatic cleaning Inhibit will result in loss of ONLY stop exhaust system
events. Only inhibit cleaning for cleaning when high
safety reasons. chances of service or repair to exhaust temperatures
EXCEPTIONAL DPF system. presents hazard. Excessive
Use Only When Necessary Non-Mission Cleaning Event use of the STOP position
will soon be required unless will result in the need for
Automatic cleaning is restored. more frequent stationary
exhaust cleaning events.

Operation
4.05.20.02 Perform Forced Regen

Warnings
! WARNING
NEVER perform Non-Mission exhaust cleaning
near combustible materials.
NEVER allow people or materials near exhaust
pipe when High Exhaust System Temperature
Lamp is illuminated. Exhaust gas temperatures
can reach 1100° F (800° C) which is hot enough
to burn, ignite or melt materials and harm
persons.
W-1018
Perform Forced Regen Exhaust System Cleaning

1� Park machine in appropriate location with
exhaust tail pipe away from people or
combustible materials.
2� Set Parking Brake.
3� Lower Engine Speed.
4� Set Travel Joystick to NEUTRAL.
5� Press 4 for Forced Regen on Exhaust

Cleaning Menu Screen. Exhaust System
Lamp will illuminate. Monitor machine and

surrounding area for safety during cleaning
event.
Engine speed and throttle will return to
normal and Exhaust Cleaning Event Lamp
and HEST Lamp will turn OFF when cleaning
is complete.
6�
Press to return to Main Menu.

Operation
4.05.20.03 Diesel Exhaust Fluid Indication Lamp

Maintain DEF tank level above 10% to prevent DEF tank low level inducements from being activated.
Control Display – Main Screen
Exhaust Cleaning
Lamps
DEF Tank Level

Operation

DEF Lamp DEF level at 10%. Engine speed and torque Fill DEF tank with DEF at earliest
ON normal. convenience.
FC 3497 Section 4.03.02

DEF Lamp Low DEF level at 5%. Engine speed and torque Fill DEF tank with DEF as soon
FLASH reduced. Engine power will be as possible.
acceptable. Section 4.03.02.

FC 3498
DEF Lamp Initial Stage – Initial Stage - Engine speed and Fill DEF tank with DEF
FLASH Approaching critical torque reduced. immediately.
DEF levels at 2.5%. FC 1673, 3714
Section 4.03.02.
Secondary Stage – Engine
Engine power limited. 30 minutes until
Secondary Stage-
Lamp ON Stop Engine warning. FC 3547,
Critical DEF levels near
3714
0%.
Engine power will be restored
acceptable ranges.
DEF Lamp 0% DEF level for 30 Engine power severely limited.
FLASH minutes. with DEF immediately.
FC 3712
Section 4.03.02.
Stop Warning displays 2 minutes
Engine before Inducement.
Lamp ON
Find DEF Fluid

Use only DEF meeting ISO 2224101 standards

Operation
4.05.20.04 SCR System Tampering / Malfunction Inducements

Operator is warned when tampering or malfunction has caused emission levels to increase.
• Disconnected tank levle anor/or quality snsor

• Blocked DEF line or dosing unit
• Disconnected DEF or dosing unit
• Disconnected DEF pump
• Disconnected SCR Wiring Harness
• Disconnected NOx Sensor
• EGR Valve Malfunction
• Any hardware or performance issues that will the NOx emission exceeding a legislated
threshold
Control Display – Main Screen
Exhaust Cleaning
Lamps
SCR Tampering / Malfunction Inducement Indicators

Operation

DEF Lamp SCR System detects PGN 65110 Check for possible
tampering or malfunction SPN 5246 tampering/malfunctions or
Equivalent of T3 Level on contact Cummins.
Exhaust Cleaning Chart
Check Engine
Lamp ON
DEF Lamp SCR System detects FC for Tampering/ Check for possible
tampering or malfunction Malfunction tampering/malfunctions or
contact Cummins.
Check Engine
Lamp ON + 2
hrs�
DEF Lamp SCR System detects Initial engine de-rate Check for possible
tampering or malfunction induced tampering/malfunctions or
contact Cummins.
Initial Inducement FC 4863
Check Engine
Lamp ON + 2�5
hrs�
DEF Lamp SCR System detects Secondary engine de-rate Check for possible
FLASH tampering or malfunction induced tampering/malfunctions or
contact Cummins.
Secondary Inducement FC 3714
Check Engine
Lamp ON + 3
hrs� 45 min�
DEF Lamp SCR System detects Final Inducement initiated Contact Cummins.
FLASH tampering or malfunction
Engine at idle speed
Final Inducement
FC 3712
Stop Engine
Lamp ON + 4
hrs�

Operation
4.06 Left Screed Control Box

Located on the left hand side of the screed.
Displays operator controls and digital display screens.
Left Screed Control Box

20 18 16 14
1 19 17 15 13
6 8 10 12
7 9 11
1� Pile Height - Adjust dial to control the amount of 11. Screen - Push UP to power on display. Push DOWN
material at the head of the screed. to power off.
2� Auger Direction - Push UP to reverse direction of 12. Digital Display Screen - See Screed Digital Screen
rotation. Push DOWN for standard forward direction. section for details.
3� Tow Point - Push UP to raise tow point. Push DOWN 13. E-Stop - Push IN to shut down engine in case of
to lower tow point. emergency. Engine will not restart until all E-stop buttons
have been disengaged. Pull OUT to disengage.
4� Auger Override - Push UP to override auger function. 14. Feeders - Press UP to set up feeder system. Push
Push DOWN to stop auger. DOWN to run.
5� Conveyor - Push UP to run. Push DOWN to stop. 15. Automation - Press UP for screed to automatically
adjust to slope settings during operation.
6� Extension - Push LEFT to extend screed extension 16. Vertical - Push UP to raise vertical screed height.
left. Push RIGHT to extend right. Push DOWN to lower.
7� Tunnel - Push LEFT to extend tunnel extension left. 17. Slope - Press UP to angle screed left. Press down to
Push RIGHT to extend right. angle screed right.
8� Left Auger - Push UP to raise. Push DOWN to lower. 18. Horn - Press UP to sound horn.
9� Berm - Push UP to raise berm. Push DOWN to lower. 19. Flow Gate
DOWN to lower.
10� Right Auger - Push UP to raise. Push DOWN to 20. Max Speed - Adjust dial to control the feed system
lower. speed.

Operation
4.07 Right Screed Control Box

Located on the right hand side of the screed.
Displays operator controls and digital display screens.
Right Screed Control Box
2 4 6 8 10
1 3 5 7 9
11
12
13
19 17 15
20 18 16 14
1. E-Stop - Push IN to shut down engine in case of 11. Tow Point - Push UP to raise tow point. Push DOWN
emergency. Engine will not restart until all E-stop buttons to lower tow point.
have been disengaged. Pull OUT to disengage.
2. Feeders - Press UP to set up feeder system. Push 12. Auger Override - Push UP to override auger
DOWN to run. function. Push DOWN to stop auger.
3. Automation - Press UP for screed to automatically 13. Conveyor - Push UP to run. Push DOWN to stop.
adjust to slope settings during operation.
4. Vertical - Push UP to raise vertical screed height. 14. Extension - Push LEFT to extend screed extension
Push DOWN to lower. left. Push RIGHT to extend right.
5. Slope - Press UP to angle screed left. Press down to 15. Tunnel - Push LEFT to extend tunnel extension left.
angle screed right. Push RIGHT to extend right.
6. Horn - Press UP to sound horn. 16. Right Auger - Push UP to raise. Push DOWN to
lower.
7. Flow Gate 17. Berm - Push UP to raise berm. Push DOWN to lower.
to lower.
8. Max Speed - Adjust dial to control the feed system 18. Left Auger - Push UP to raise. Push DOWN to lower.
speed.
9. Auger Direction - Push UP to reverse direction of 19. Screen - Push UP to power on display. Push DOWN
rotation. Push DOWN for standard forward direction. to power off.
10. Pile Height - Adjust dial to control the amount of 20. Digital Display Screen - See Screed Digital Screen
material at the head of the screed. section for details.

Operation
4.08 Screed Digital Display - Main Screen
Main Display Screen
Push UP on the Screen toggle switch to power on the digital display screen.
per-minute (FPM).
Adjust temperature with buttons 1 and 2 (up and down arrows).
Press 3 for Generator ON/OFF.
Press 4 for Heat ON/OFF.

Operation
4.09 Screed Digital Display - Auger Raise Screen
Auger Raise Screen
Push UP on the Screen toggle from the Main Screen to enter the Left/Right Auger Screen.
Flow gate height monitors are visible on upper section of page.
Left and Right Auger depictions are shown with corresponding arrows. Press UP/DOWN arrows to
raise or lower Augers in inches.

Operation
4.10 Screed Digital Display - Flow Gate Height Screen
Flow Gate Height Screen
Push UP on the Screen toggle from the Auger Raise Screen to enter the Flow Gate Height Screen.
Left and Right Flow Gate depiction is shown with corresponding arrows. Press UP/DOWN arrows to
raise or lower Flow Gates in inches.

Operation
4.11 Screed Digital Display - Screed Settings Screen
Screen Settings Screen
Push UP on the Screen toggle from the Flow Gate Height Screen to enter the Screed Settings
Screen.
Press 3 to unlock settings feature. Settings can be locked by pressing 3 again.
Press UP/DOWN arrows to raise or lower Crown/Slope/Vertical/Berm.

Operation
4.12 Screed Digital Display -Service Screen Menu
Service Screen Menu
Press button 2 (ENTER) to enter the service menu.

Operation
4.13 Screed Digital Display -Screed Control Screen 1
Screed Control Screen 1
Monitor the status for slope, vertical height, automation, feeders, ad setup/run. The green light
means the switch is active.
Press button 4 (right arrow to advance to the next screen) Button 3 (left arrow) returns to the
previous screen.
Press button 1 (x) to exit the menu.

Operation
4.14 Screed Digital Display -Screed Control Screen 2
Screed Control Screen 2
right auger, extension, tunnel, and berm.

Press button 4 (right arrow) to advance to the next screen; Button 3 (left arrow) returns to the
previous screen.

Operation
4.15 Screed Digital Display -Remote Box Screen
Remote Box Screen
Monitor the status for slope, towpoint, vertical, auger override, tunnel and extension.
previous screen.

Operation
4.16 Screed Digital Display -MC50-110 Screed Controls
MC50-110 Screed Controls
Monitor the status for LH extension extend, LH extension retract, LH vertical increase LH vertical
decrease, slope increase, slope decrease, berm increase, RY13 Coil MOBAjpin, LH towpoint raise,
LH towpoint lower, vibrator, berm of decrease. Right hand screen will show crown increase and the
RY15 coil MOBAjpin.
previous screen.

Operation
4.17 Screed Digital Display -MC50-110 Screed Outputs
MC50-110 Screed Outputs
Monitor the outputs for heat on, RY8 aug/conv manual relay, auger conveyor current, feed control
RY12 coil. Heat on only show on Left hand screen. Right hand screen will berm decrease and crown
decrease, and RY9 aug/conv manual relay.
previous screen.

Operation
4.18 Screed Digital Display -CAN Network Health Screen
CAN Network Health Screen
Monitor the CAN network health for LOC_DM430, ROM_DM430, LIM, RIM, left screed control, right
screed control, left MC024 control, right MC024 control, right screed DM-430, left screed DM-
430, main J box control, opt in mod (CAN1), LOM Mod 1 (CAN1), LOM Mod 2 (CAN2), ROM Mod 1
(CAN2), ROM Mod 2 (CAN2), S10X Screed MC050-110, and Joystick CAN0.
Press button 4 (right arrow) to begin the rotation of service screen again.
Button 3 (left arrow) returns to the previous screen.

Operation
4.19 Screed Digital Display -Screen Backlight
Screen Backlight
Press button 2 (up arrow) to increase light by 10%

Press button 3 (down arrow) to decrease light by 10%
Press 4 to EXIT to Main Screen.

Operation
4.20 Screed Digital Display -Screed Setpoints Screen
Screen Setpoint Screen
ONLY available when the S-10X screed is installed.

Press button 1 (down arrow) to toggle through menu items for LH EXT, LH HSSO, LH Main, RH Main,
RH HSSO, and RH EXT.
Press buttons 2 and 3 (DEC and INC) to decrease or increase values.

Operation
4.21 Screed Digital Display -Screed Temperatures
Screed Temperatures
ONLY available when the S-10X screed is installed.

Monitor screed and heating element temperatures. The top value in each set represents the setpoint
value. The bottom number represents the actual temperature reading.

Operation
4.22 Screed Digital Display -Paver Production Screens-Guardian
Paver Production Screens for Guardian - Tons and Feet Paved Totals Screen
Monitor tons per hour, total tons paved, total feet paved, and total paving time. This screen is
found on Left Screed Digital Display ONLY and only if machine option is available�

Operation
4.23 Screed Digital Display - Paver Production Screens-Guardian
Paver Production Screens for Guardian - Adjust Calibration Factor
Run a known amount of material through the machine.

Press button 2 (down) or button 3 (up) to adjust the displayed amount to the actual amount of
material run the machine. This will provide matching totals going forward. Paver production
screens found only on Left Screed Digital Display and only if option is available�

Operation
4.24 Screed Digital Display -Total Feet Screen
Total Feet Screen
Reset the Foot Total Values, then drive the machine to a known distance.
Press button 1 (reset) to reset values for total feet traveled.
Press button 4 (reset) to reset the total feet for machine.
Press button 2 (CAL) to calibrate.

Operation
4.25 Screed Digital Display -Total Feet Calibration Screen
Total Feet Screen
Press button 2 (CAL) from the Total Feet Screen to calibrate Total Feet.
Reset the Foot Total Values, then drive the machine to a known distance.
Use the arrows to adjust the displayed value to the actual value.
Press button 1 (reset) to reset values
Press button 2 (up arrow) to increase total feet
Press button 3 (down arrow) to decrease total feet

Operation
4.26 Screed Digital Display - High Heat Screen
High Heat Screen
Press and hold button 1 as the digital screen powers up to access the High Heat screen�
This feature appears on the Left Hand screen only�
Press button 2 (ENABLE) to enable high heat.
Press button 3 (DISABLE) to disable high heat. The status will show on the main screen.
Press button 4 (EXIT) to the main screen.

Operation
4.27 Screed Digital Display - Screed Offset Temp/Generator
Screed Offset Temp / Min. Generator Speed
Press and hold button 1 as the digital screen powers up to access the Screed Offset Temp
and Min� Generator Speed screen� This feature appears on the Right Hand screen only�
Press button 1 (SELECT) to toggle between the screed offset features and the min. generator speed
option. Selection will highlight in green.
Press button 2 (DEC) to decrease offset value by 1 point or decrease RPMs by 100.
Press button 3 (INC) to increase offset value by 1 point or decrease RPMs by 100.
Press button 4 (EXIT) to the main screen.

Operation
4.28 Remote Screed Box

Use the remote screed boxes for ground operations, including right and left side screed extension speed,
auger controls with override, tow point raise/lower, vertical and slope controls and hydraulic tunnels left/
right controls.
Remote Screed Pendant
1 2

Operation
Remote Screed Box Controls

1� Slope Left/Right Adjustment
Push Left Arrow to adjust screed slope left. Push Right Arrow to adjust screed
slope right.
2� Slope Up/Down Adjustment
Push Up Arrow to raise screed slope. Push Down Arrow to lower screed slope.
3� Tow Point Raise / Lower

Push Up Arrow to raise tow point. Push Down Arrow to lower tow point.
4� Auger Override/Stop
Enable or disable auger.
5� Screed Tunnel Switch

Extends or retracts left and right side screed tunnel.
6� Screed Extensions Switches

Extends or retracts left and right side screed extensions.

Operation
4.29 Pre-Start Conditions

Asphalt paving requires a skill for balancing several variables. The screed operator must control the
Correct angle of attack

Constant paver speed
Consistent head of material
The Line of Pull describes the critical

relationship between the tractor, the
screed and the paving surface. The
tractor will average the ride, but
the proper line of pull must also be
maintained between the surface and the
screed. This relationship is set using the
tow-point.
An incorrect line of pull will result in
increased wear rates and reduced
pre-compaction of material.
Additionally, the incorrect line of pull
rates.
The high tow point with a thin lift will
result in an upwards pull. The upwards
pull applies pressure to the screed nose,
resulting in a quick upwards movement
and sluggish downward movement.
The low tow point with a thick lift will

result in a line of pull that pulls downward
on the screed rear. This will result in
a slow reaction time to increase mat
thickness.

Operation
Set the tow point 1 inch higher than

the loose mat thickness to be paved as a
general rule.

Operation
4.30 Pre-Start Check List

Read and understand operation and safety procedures for this machine before operating.
Connect auger and conveyor wires to pump controls on new machines.
Remove parts kits from hopper area before starting machine. Never operate conveyors until the parts
kit has been removed.
Inspect the paver and ensure all tools and loose items are removed from the paver decks. Ensure all
steps and hand-holds are free of grease and oil.
Keep a safety focus. Observe safety decals and warnings.
Become familiar with all machine controls.
Understand and follow all hazard alert decals on machine.
Allow only one operator on platforms at time. Forbid riders.

Walk around machine and perform visible inspections.
Check all lubricant, coolant and fuel levels.
machine. Make repairs before starting machine.

Insert spray bar nozzles.
Ensure all emergency stop buttons are on RUN.
Ensure battery disconnect switches are on. Check for possible safety lock out tags on switches.
Board machine using 3-point connection on steps and handrails provided across the screed.
Set beacon lights to ON.
Test hopper sides, screed lift and hydraulic extensions.
Listen for unusual noises or vibrations.
Ensure all personnel are clear of machine and drive-off zone.
Ensure total visibility. Check that mirrors are mounted and positioned correctly. Never remove mirrors.
Replace missing mirrors immediately.
°F (51.6 °C - -23.3 °C). Operate
°F – -10 °F (104 °C - -23.3 °C).
! WARNING
Avoid serious injury or death.
NEVER start a machine with safety lockout tag
attached.
NEVER move machine into path of moving
vehicles.
NEVER change speeds while the machine is in
motion. Always bring machine to a complete stop
before shifting between speeds.
NEVER work at a speed greater than conditions
allow.
NEVER operate machine on slopes or uneven
surfaces.
NEVER operate machine on wooden bridges and
bridges not rated to support machine weight.
W-1019

Operation
Paver Speed for Tons Per Hour and Mat Thickness (Imperial)
Based on 12 ft.-wide lane. Mix compacted to 140 lbs./cu. ft.
Paver Speed Mat Thickness (Inches)

(Feet Per Minute) 1 2 3 4 5 6 7 8
10 42 84 126 165 210 252 294 336
15 63 126 189 252 315 378 441 504
20 84 168 252 336 420 504 588 672
25 105 210 315 420 525 630
30 126 252 378 504 630

35 147 294 441 588
40 168 336 504 672
45 189 378 567 756
50 210 420 630

55 231 462 693
60 252 504 756

65 273 546 819
70 294 588
75 315 630
80 336 672
Paver Speed for Tons Per Hour and Mat Thickness (Metric)
Based on 3.7 m.-wide lane. Mix compacted to 2243 kg/cu. m.
Paver Speed Mat Thickness (Millimeters)

(Meters Per Minute) 25�4 50�8 76�2 101�6 127�0 152�4 177�8 203�2
3�0 38 76 114 150 191 229 267 305
4�6 57 114 171 229 286 343 400 457
6�1 76 152 229 305 381 457 533 610
7�6 95 191 286 381 476 572
9�1 114 229 343 457 572

10�7 133 267 400 533
12�2 152 305 457 610
13�7 171 343 514 686
15�2 191 381 572

16�8 210 419 629
18�3 229 457 686

19�8 248 495 743
21�3 267 533
22�9 286 572
24�4 305 610

Operation
4.31 Pre-Start Communication

Know Your Role and Responsibilities
PAVER OPERATOR
Communicate with the crew
Prepare the machine for work
Position the paver

Maintain a constant speed
SCREED CREW
Set up screed
Communicate with the driver
Check crown
Check extension height settings
Position Augers
Position Sensors
Maintain constant head of material
Check depths and levels
Watch for soft-base surfaces
DUMP CREW
Ensure safe and smooth truck engagement. Watch out for power lines, limbs and other obstructions.
Ensure material is discharged en masse instead of dribbled into the paver.
Eliminate spillage potential. Keep roadway in front of paver clear of material.
Communicate with the driver - ensure the truck driver and paver operator know when you are
from truck drivers.

Operation
4.32 Screed Operations
Forces Acting On the Screed

The Pull Force, Force P, is determined by the speed at which the paver tractor is pulling the screed.
Force M, the Head of Material, is pushing against the pull, as is the Shear Force, Force F, between
the material and the screed.
Force W, the weight of the screed is pushing down against the upward Force R, the Reaction of the
Material Beneath the Screed.
The screed will fall when the paving speed increases due to the reduction of the head of material.
The head of material also falls when the screed extensions are opened.
width and depth.
Correction Time
1 1/2 paver lengths or 5 tow-arm lengths (50’-60’ or 15.25-18.25 m) are required in order for the
screed to correct given the forces enacted upon it.

Operation
4.33 Prepare the Screed

Stringline the Screed
Stretch a string across the screed to ensure the screed is level�

1� Check the rear of the screed and adjust to level.

Operation
4.34 Screed Set Up

Set Up Screed
See the following pages for details on the steps to set up the screed.
1� Check crown, extensions, angle of attack, slope and height settings.

2� Set starting blocks including compaction roll down. The rule of thumb for starting block size is mat
thickness plus 25%.
3� Null screed.
4� Set to positive angle of attack.
Set Tow Point

Set both tow points to depth of mat. The rule of thumb is to set the tow points at mat depth + 1 in.
(25 mm).
Remove any slack from tow arms by moving forward.

Operation
Set Pre Strike-Off

Mix designs vary and the pre strike-off plates must be adjusted in order to cause the screed to ride
correctly over the mat being laid down.
The force of the
direction. The screed will ride on the nose when the strike-off is adjusted too low. Premature
wearing of the front of the screed plate or bull nose will occur.
Set the bottom of the strike-off to 1/2” above the screed bottom. Adjust the strike-off from the top
of the screed (12.5 mm).
Set Crown Height

Lead crown refers to having more crown in the front of the main screed plate than on the rear
compaction.
Check the crown using a stringline.
Set to 1/8” (3.175 mm).

Operation
Null Screed
1� Raise Screed UP.
2� Position boards beneath screed that are
equal in thickness as the unrolled mat
depth.
IMPORTANT: Fully support the screed
for every 10 feet of screed width.

3� Lower Screed to rest on boards.
4� Turn depth cranks until screed face is
resting level on boards.
5� Turn depth cranks one full turn counter-
clockwise to set an initial angle of attack.
The rear extension is set to 3/16” (4.5
mm). Hand cranks will have a small area of
rotary movement where little resistance is
felt. This indicates that the screed is nulled
out.
head
screed type.
6� Set Screed heating to ON to pre-warm
screed to the same temperature as the
material to avoid material adhering to the
screed bottom plate.
IMPORTANT: Never under-heat or
Set Angle of Attack (including Screed Extensions)

The pressure exerted by the rear pressure
plate must be equal along the ENTIRE plate in
order to produce a mat of consistent density
and texture.
As the angle of attack is changed on the main
screed, it affects the vertical position on the
rear extension. The angle of attack is normally
set on the rear extension to 3/16 (4.5 mm).
The tail of the extension should touch the level
and show a 1/4” (6.5 mm) air-gap at the front
of the extension.
Check
level along the main screed. Adjust as needed.
Adjustment
Bolt

Operation
Set Auger Height

Auger height is determined by mat thickness and will control the head of material.
Add 2” (50 mm) above mat height to auger height setting.
Adjust Pile Height and Head of Material

head of material.
Run augers 100% of the time. Ensure there is an even amount of material across the auger
chamber.
Use head of
material.

Operation
4.35 Feed System Set Up
Feed System
The paver is equipped with an ultrasonic feed control system that automatically control the conveyor
speed and auger speed in order to maintain a consistent head of material at the screed. The feeder
system also promotes material mixing that produces a higher quality mat.
Set Flow Gates

Flow Gates are designed to meter the amount of material that is delivered to the auger chamber.
show an even amount of material across the tunnel, and the augers should turn freely.
Set
chamber.

Operation
Steps to Set Up Feed System

1� Set Pile Height. The rule of thumb is to set the
dial at 3-4.
2� Set Augers 2” (50 mm) or higher than mat.
3. Set Flow Gates. The rule of thumb is 3-4.
4� Feed auger tunnel and extensions with a
uniform head of material (half the auger
height).
5� Position sonic feed sensor on end gate so
that it is directed toward the rolling face of the
head of material and positioned at 90 degrees
to face of material.
6� Set Auger Speed. The rule of thumb is 3-4 on
the dial.
7� Adjust Pile Height using dial to adjust the
height of material as needed.
IMPORTANT! Never adjust augers speed.
8� Ensure the Feed Set Up switch is in the RUN

position once a uniform head of material is
achieved.

Operation
Keep Hopper Filled with Material

Stop
Keep conveyor deck covered with a minimum of 6 in. (152 mm) of material at all times.
Empty the hopper as seldom as possible to achieve a more quality mat.
Truck Exchanges
1� Maintain contact with drivers. Explain how much material is needed each time drivers unload.
2� Ensure trucks stop approximately 20” (.5 m) in front of the paver, then allow the paver to engage
the truck. The driver should release the truck brakes to allow the paver to push against the truck.
The dump operator will then signal the driver to raise the truck bed and begin dumping the load.
3� NEVER allow trucks to bump the paver to prevent bumps and ridges in the mat.
4� NEVER allow spillage so that mix is not compacted by the paver wheels, resulting in cold spot and
uneven mat density.

Operation
4.36 Paving Techniques
Mat Thickness
Roll down is the differential value between non-compacted and compacted material.
Always allow room for roll down to achieve proper mat thickness.
Desired Final Mat Thickness Initial Thickness Required
1 in. (25.4 mm) 1.26 in. (32.0 mm)
2 in. (50.8 mm) 2.53 in. (64.3 mm)
3 in. (76.2 mm) 3.79 in. (96.3 mm)
4 in. (101.6 mm) 5.05 in. (128.3 mm)
Material Management
Keep material contained.
Prevent excessive rolling of materials.
Move material in a smooth uniform, uninterrupted manner.
Head of Material
Gradation changes in the mix design will affect the screed’s reaction. When the head of material is
irregular, the same imperfections will exist in the mat.

Operation
Paving Techniques for Smoothness

Paving techniques and mix quality are critical to mat smoothness and durability. The Roadtec® RP-170e
paver will produce a long-lasting, uniform mat if best practices are followed. Adjustments to the crown,
automatic feed control and leveling systems may be required. Wide-width paving jobs may require the
use of the 40-ft. sensor ski. Certain operational variables will continue to negatively impact the mat
Worn auger and screed components

Fluctuating mix temperatures
Paving thinner than the largest mix aggregate
Inconsistent blend of aggregate mixes
Roller improperly operated or maintained
Trucks holding brakes or bumping paver
Stop-and-go paving
Pave with Proper Aggregate Sizes

General rule:
No mat should be thinner than twice the size
of the largest aggregate�
Mixes designed for correction course paving or
one-pass paving contain 5/8 to ¾” or smaller
Aggregate size 1” to 1 1/2” can pass through

a 3/3 screen, resulting in mix with larger
aggregate than is ideal.
Mat thickness will not be uniform; thin spots
will drag aggregate along producing voids.
Ensure mat depth will be at least twice the size
of the largest aggregate in the mix.
Prevent Ripples
Ripples are wave patterns in mat that can be observed on edges and across mat width. Ripples
negatively impact durability and driving quality. The main cause is poor asphalt mix with too little
General rule:
Address each condition listed below to prevent ripples�
Inconsistent mix size and temperature
Poor foundation and subsurface condition
Paver, screed plates or augers in disrepair
Malfunctioning auto grade control
Low tire pressure
Loose screed pivot point
Loose screw at angle of attack
Poor operating practices, including improper strike-off settings, paving too fast/too thin, improper amount of
material at head of screed
Trucks holding brakes or intermittently applying brakes
Rollers rolling too quickly or rolling before mat is cooled
Rollers in poor condition

Operation
Prevent Bumps and Depressions

General rule:
Keep paver constantly moving and require
good haul truck management�
Bumps and depressions are a result of screed
settlement when the paver stops.
The auto grade system detects settlement as a
dip and increases the angle of attack.
Tow points falsely correct, causing the screed
to rise above the mat thickness, creating a
bump.
Auto grade detects the bump, and then
reduces the angle of attack, which results in
another dip, causing the poor paving cycle to
repeat.
15-20 feet is required before equilibrium is
again achieved.
Control Yield Factor

General rule:
Control mat depth to control yield factor�
Refers to calculated material amounts required
Yield = job length x job width x job depth

Yield Factor is a primary challenge of paving
operations.
Greater correction to road surfaces means

greater material usage.
Manually adjust mat depth with angle of attack
jacks; NEVER over-correct depth cranks.
Adjust Paver
Paver adjustments are critical to mat quality.
position and material head levels.

Underfeeding augers results in bumpy mat
surface.
Overfeeding augers creates ripples and
shadows in mat, and causes excessive auger
wear.

Operation
Understand Transverse Joints

Transverse joints are the points
where previously paved mat joins
newly paved mats and form when
paving operations resume. Joint
mat quality.
Poor transverse joints result in
dip faults.
Follow transverse joint
construction procedures.
Prevent Dip Faults

General rule:
Maintain constant head of
material throughout entire paving
operation to prevent dip faults�
Created when screed falls and
amounts of material at screed

heads.
Created when screed is cold.
Taper ascends as paving
operations resume creating a
V-shape or dip in the mat.
Prevent Poor Longitudinal Joints
inches.
Rely on the joint matcher or the sensor to match the joint properly when using automatic
equipment. Poor joints result from manually operating screed depth cranks and overcompensating,
distance from the edge of the reference mat when needed to decrease deviations caused by rollers

Operation
4.37 Create Quality Transverse Joints
Create Quality Transverse Joints

1� Maintain a consistent screed
level until paving stops.
2� Raise the screed, then move

paver away from the joint.
3� Use a rake or a lute to establish

a square edge in the unrolled
mat. Keep the roller operator
back at least 6 ft. from the joint
edge.
4� Construct a wedge using
material raked away from the
squared edge. The straight
section on the wedge prevents
the roller from breaking the
squared edge of the previous
mat, while also maintaining
uniform compaction.
5� Roll the transverse joint using

rolling patterns and techniques.
6� Remove the temporary wedge

when paving operation begins.
7� Spray tack coat on squared edge

of mat.
8� Preheat screed to 300 degrees
F.
9� Position screed over new mat
with screed front aligned to
square edge.
following page for the take-off

block height.

Operation
10� Refer to the table below for take-off block height.
Block Height 1�00 2�00 3�00 4�00 5�00 6�00 7�00 8�00
Material Density MATERIAL THICKNESS (INCHES)

Behind Screed %
76% 0�26 0�53 0�79 1�05 1�32 1�58 1�84 2�11
78% 0�23 0�46 0�69 0�92 1�15 1�38 1�62 1�85
80% 0�20 0�40 0�60 0�80 1�00 1�20 1�40 1�60
82% 0�17 0�34 0�51 0�68 0�85 1�02 1�20 1�37
84% 0�14 0�29 0�43 0�57 0�71 0�86 1�00 1�14
86% 0�12 0�23 0�35 0�47 0�58 0�70 0�81 0�93
88% 0�09 0�18 0�27 0�36 0�45 0�55 0�64 0�73
90% 0�07 0�13 0�20 0�27 0�33 0�40 0�47 0�53
92% 0�04 0�09 0�13 0�17 0�22 0�26 0�30 0�35
94% 0�02 0�04 0�06 0�09 0�11 0�13 0�15 0�17
11� Position blocking under screed

and away from square edge.
12� Null screed and introduce angle

of attack.
13� Establish correct head of

material amount. Use shovel to
material head is equivalent to

standard amounts used during
paving operation.
14. Resume paving at the same

speed used when paving previous
mat.
15� Fill in voids at the joint when the

screed has cleared the joints.
16� Remove hot mix left on cold

surface.
17� Lute joint to obtain a uniform,

smooth surface across the joint.

Operation
Finalizing the Transverse Joint

1� Pinch Pass A and Pass B in both transverse and longitudinal joints. The pinch can be accomplished
by overlapping 8-10 inches of roller on the edge of the previous mat, and then pinching the unrolled
mat down to and onto the surface level of the reference mat, as shown.
2� Pass C and Pass D should pass over the joint at an angle to prevent the newly laid mat from
pushing away from the joint.
roller does not produce a bump at the joint.
3� Pass A should be on the hot mat 8-10 inches away from the cold joint with B pass rolling this ridge
of 8-10 inches of hot material in the direction toward the cold mat.

Operation
The Second Pass on a Two-Pass Transverse Joint

1� Correctly position the joint matcher.
2� Clear the area of the second pass of any large aggregate before rolling.

Operation
Set Up the Job

1� Determine
2� Determine the tonnage per hour to calculate paver speed.
3� Adjust the operation in case of changing circumstances.
4� Check depth and yield before operations begin. Be aware of grade conditions, such as slope, low
spots, high areas and HMA makeup. Remove high spots prior to paving. Mat thickness should be 1.5
times greater than the maximum aggregate size.
5� Communicate with the crew for higher productivity.
6� Use Grade Stakes for marking lines, radius points, ditches and back slopes.
7� Match production rates to the paver size.
8� Consider existing grade conditions. Pre-compacted material is considered an existing grade

condition. Never confused texture strips with segregation. Existing grade conditions can cause
texture stripping to occur due to the mat thickness.
9� Advance rubber tire pavers on stone or wet tack using the speed pot rather than the joystick.

Operation
4.38 Auger Extensions
Auger Extensions
Auger extensions are used to maintain a uniform head of material when the screed width is
increased.
Warnings
! DANGER
Avoid serious injury or death!
NEVER service augers or conveyors, whether assembled
or disassembled, while the engine is running.
D-1116
Assemble Extension
1� Remove
adjacent to auger hanging
for later re-installation.
2� Remove end cap and store.

Operation
3� Install 1-foot basic shaft
removed in step 1. Use anti-

seize.
4� Install
Leave off end plug if additional
auger extension is required, and
assemble additional extensions.
5� Torque all bolts.
6� Install 1-foot additional shaft

assembly by applying anti-seize
onto both holes then sliding
the shaft into the hole normally
occupied by the end plug.
7� Install
previous step. If additional
extensions are required, leave off
repeat this step.

Operation
8� Install
the last tunnel extensions with
brackets for bearing and strut
attachment.
9� Align holes, then slide bearing

hanger shaft into auger shaft.
10� Bolt hanger bearing to tunnel

extension using standard bolts.
11� Install
12� Fasten strut between last tunnel

extension and ear on tow point
support.
13� Adjust length by rotating rod.
14� Torque all bolts.

Operation
4.39 Paving for Smoothness Tips

Keep the hopper full.
Control hopper wing cycling.
Use a hopper insert.
Maintain a consistent head of material.
Time the conveyor and auger system.
Keep the paver speed steady.
Correct lead crown setting and strike off
adjustments.
Correct auger length.
Use a thermal gun.
Don’t broadcast material.
Use the grade control system.
Train the crew.

Operation

Operation
4.40 Drive-Off Procedure

1� Turn Battery Disconnect Switch ON.
2� Turn E-Stops OFF.
3� Set Joystick to CENTER (neutral).
4� Set Parking Brake ON.
5� Set Range to LOW (pave range).
6� Turn Beacon Lights ON.
7� Ensure Feed System is OFF.
8� Start Engine by pushing Main Power switch to

ON (CENTER position). Preheat light turns ON.
9� Wait until preheat light is OFF. Sound Horn.

Push Main Power UP and hold for 2-3 seconds
or until engine engages. Engine will engage at
idle speed.
10� Allow engine to idle for 2-3 minutes. Allow
coolant temperature to rise to 158°F (70°C).

Operation
11� Set Throttle to HIGH (1900 RPM). Check

gauges at full engine RPM for engine fault or
error codes.
12� Push Screed Lift UP and hold until screed is

fully raised.
13� Release switch and attach left and right

support cables at rear of machine to pins on
screed as shown.
14� Lower screed until it rests on support cables.
15� Position tow points at bottom of scale with

screed raised to maximum height and resting
on screed support cables.
NOTE: Ensure screed will completely clear
truck and ground while loading/unloading.
16� Release Parking Brake.
17� Set Travel Joystick forward or reverse direction

to move machine accordingly.
18� Travel machine to desired location. Stop

machine by moving Travel Joystick to center
position.
NOTE: Adjust paver speed using Travel Speed
dial. Stop machine by moving Travel Joystick
to Center position.

Operation
4.41 Operate
1� Turn Battery Disconnect Switch ON.
2� Turn E-Stops OFF.
4� Ensure feed system is OFF.
5� Turn screed heat ON.
8� Turn Beacon Lights ON.
9� Start Engine by pushing Main Power switch to

ON (CENTER position). Preheat light turns ON.

Operation
10� Wait until preheat light is OFF. Sound Horn.

Push Main Power UP and hold for 2-3 seconds
or until engine engages. Engine will engage at
idle speed.
11� Allow engine to idle for 2-3 minutes. Allow
coolant temperature to rise to 158°F (70°C).
12� Set Throttle to HIGH (1900 RPM). Check
gauges at full engine RPM for engine fault or
error codes.
13� Push Screed Lift UP and hold until screed is

fully raised.
14� Release switch and attach left and right

support cables at rear of machine to pins on
screed as shown.
15� Lower screed until it rests on support cables.
16� Position tow points at bottom of scale with

screed raised to maximum height and resting
on screed support cables.
17� Release Parking Brake.

Operation
18� Select console for operator control.
19� Set Travel Joystick forward or reverse direction

to move machine accordingly.
20� Adjust paver speed using Paver Speed.
21� Position paver at paving starting point.
NOTE: Stop machine by moving Travel

Joystick to center position.
24� Set Screed to Float Mode
25� Set Screed in place and remove slack from tow

arms by moving forward.

Operation
26� Position loaded haul truck or material transfer

vehicle against rollers.
27� Raise or lower hopper to receive load.
28� Lower Frame down 7-10 seconds, or until it (OPTIONAL)

hits bottom.
29� Raise Frame up 2 seconds for optimal ground

contact.
30� Set Tow Point Scale.
31� Position End Gates for paving width.
32� Set Flow Gates based on width of paving.
33� Set extension height and slope (if applicable).
34� Set Crown height. (See Set Crown Height.)
35� Null screed. (See Null Screed.)
36� Set the Angle of Attack. (See Set Angle of

Attack.)

Operation
37� Turn Feed System ON.
38� Set Auger height.
39� Set Feed Speed dial.
40� Set Feed Mode to AUTO.
41� Turn Augers ON.
42� Fill hopper with material and allow auger
43� Set Throttle to HIGH (1900 RPM).

Operation
44� Set Parking Brake to OFF.
45� Sound Horn.
46� Set Travel Joystick to FORWARD and slowly

increase speed knob until desired speed is
reached.
47� Adjust feeder controls as needed.
48� Adjust Flow Gates as needed.
49� Adjust depth as needed.
50� Adjust grade system as needed.
51� Start paving slowly and remain consistent.

Operation
4.42 Park and Shut Down

1� Move machine to designated cleaning area
using Joystick.
3� Set Parking Brakes ON.
4� Set Throttle to LOW. Idle machine for three

minutes.
5� Set Range to LOW.
6� Turn Beacon Lights OFF.
7� Turn Screed Heat and Generator OFF.

8� Scrape asphalt buildup from auger posts,
screed extensions, steering components and
push beam.
9� Spray release agent on augers, conveyors,
hoppers, screed extensions and side plates.
10� Raise screed extension verticals to fully raised
(in case of machine transport).
11� Grease machine per lubrication chart. See Lubrication Chart

Operation
12� Shut down machine engine.
13� Set Battery Disconnect Switches to OFF.
14� Perform Lockout/Tag-out procedures.

Lubrication & Maintenance
5.0 Lubrication & Maintenance


5.01 Service Summary

The life and reliability of a Roadtec RP-170e Rubber Tire Asphalt Paver is greatly affected by the frequency
of maintenance. Dirt particles cannot be seen with the human eye, yet cause thousands of dollars of damage
to mechanical and hydraulic systems. Commit to the following maintenance and lubrication schedules to
maximize the life of the Roadtec RP-170e Rubber Tire Asphalt Paver.
1. Store lubricants in clean, covered and marked containers.
2. Clean containers used to carry lubricants from bulk storage tanks.
3. Clean around caps and plugs before removing.
4.
5. Wash funnels with solvents and thoroughly dry before and after each use.
6.
performing lubrication.
7. Perform lubrication at end of day, just after machine wash down.
8. Follow lubrication schedules for suggested service frequencies.
9. Service machine more often than schedule recommends during severe operating conditions.
10. Use only approved lubricants.
11.
12.
13.
14.
pump on standard one-pound grease gun.
15.
week.
16. Apply motor oil sparingly to provide necessary lubrication that prevents rust formation.
17. Clean components and apply anti-seize when rust has not yet formed.
18. Visually check entire machine for loose cap screws, nuts and pins. Repair and replace worn or
damaged hardware.

5.01.01 Service Safely

Follow the manufacturer’s service manual and maintenance schedules to maintain the proper
functionality of the machine and all its components.
Always stop the engine and disconnect the batteries before servicing machine.
Use proper tools in good working condition.
Allow machine to cool before performing maintenance or repair.
Disconnect battery and engine electronics before servicing machine.
Use extreme caution when working beneath machine or any component.
Stand to the side of the coolant tank when removing cap. Ensure radiator is cooled before servicing.
! WARNING
Avoid serious injury and death!
NEVER perform service or repair until completing
machine shut down and lockout/tag out
procedures.
NEVER rely on hydraulic support alone when
working beneath equipment - use proper supports.
W-1020

5.02 Fluid Requirements
Component Fluid Interval Capacity

Fuel Tank Ultra-Low Sulfur Diesel Fuel Fill Daily 81 gal. 308 L
DEF Tank Diesel Exhaust Fluid Fill at 5 gal. 19 L
Hydraulic Tank ISO Vis. Grade 46 Hydraulic Oil Check Daily 66 gal. 249 L
Gravity API 30.2
CSt at 40oC - 46
CSt at 100oC - 6.6
SUS at 100oF - 239
SUS at 210oF - 49
Viscosity Index - 95
Hydraulic Fluid must meed
Engine Oil 15W40 Engine Oil (API CJ-4) 18.5 qts. 17.5 L
Refer to the engine operation 1000 Hours
and service manual for more
information.
For European applications,
ACEA E9 diesel engine oil may
be used.
Engine Coolant 50/50 Mix High Performance Check Daily 8.75 gal. 33 L
Anti-Freeze & Water
1000 Hours
Gear Oil Synthetic, high performance Planetaries and Hydraulic
Gear Oil 80W-140 Pump Drive;
Grease Points High temperature grease - See Lubrication Chart

NGLI grade 2 Shell


5.03 Daily Maintenance


5.03.01 Refill Diesel Fuel
81 gal. tank (306 L)

Use reputable grade diesel fuel with sulfur content below 0.0015%.
Use only winter-grade fuel when operating at low ambient temperatures.
Higher sulfur contents affect oil change intervals.
Warnings
! WARNING
NEVER
NEVER dispose of cigarettes, cigars or matches
near machines.
NEVER
W-1012
Refill Diesel Fuel Tank

1� Shut down machine.
2� Locate
station. The fuel gauge is located below at
the step to the operator’s station.
3� with fuel promptly to prevent tank
injection lines.

5.03.02 Refill Diesel Exhaust Fluid
Diesel Exhaust Fluid (DEF) is part of the After-treatment system that helps reduce engine
emissions, resulting in cleaner air quality.
5 gal. tank (19 L). Use only Diesel Exhaust Fluid that meets the 1SO-22241-1 requirements.
Warnings
! WARNING
Avoid serious injury!
ALWAYS follow all safety requirements in the
engine manufacturer’s manual.
NEVER
contact with skin or eyes.
NEVER
W-1021
Refill Diesel Exhaust Fluid

1� Locate
right side of operator platform.
2�
3� Use only DEF that meets ISO-22241-1

requirements.

5.03.03 Check Engine Crankcase

Check engine crankcase lubrication points daily.
Warnings
! WARNING
ALWAYS follow all safety precautions listed in the
NEVER perform service or maintenance
until machine is shut down and batteries are
disconnected.
W-1022
Check Engine Crankcase

1� Check lube points on engine crankcase.
2� Lubricate if needed.

5.03.04 Check Engine Oil Level

Check engine oil levels daily.
Warnings
! WARNING
disconnected.
W-1022
Check Engine Oil Level

1� Check engine oil level daily using dipstick
located under hood on machine left side.
2� Ensure levels fall between ADD and FULL

marks.
3� Add SAE W-40 Shell or equivalent when

needed.

5.03.05 Check Engine Coolant Level

Check engine coolant levels daily.
Warnings
! WARNING
disconnected.
W-1022
Check Engine Coolant Level

1� Check engine coolant level daily using sight
gauge located on machine left side.
2� Add 50/50 anti-freeze and water when

needed.
IMPORTANT! Maintain engine coolant
3� Keep radiator clean of debris and dirt. The

radiator is clean when light can visibly pass
from one side to the other.

5.03.06 Lubricate Conveyor Idler and Headshaft Bearings

Lubricate conveyor idler and headshaft bearings daily.
grease.
Warnings
! WARNING
disconnected.
W-1023
Lubricate Conveyor Idler and Headshaft Bearings

1� Lubricate (4) conveyor idler bearings with 6
shots each while still hot. 6 Shots 6 Shots
12 Shots
2� Lubricate (2) headshaft bearings with 12

shots purged while hot. 6 Shots
12 Shots 6 Shots

5.03.07 Lubricate Screed Vibrator Bearings

Lubricate vibrator bearings daily.
Warnings
! WARNING
disconnected.
W-1023
Lubricate Vibrator Bearings

1� Lubricate (4) bearings located
on screed with 2 shots of high
temperature grease.

5.03.08 Lubricate Auger Hanger and Chain Case Bearings

Lubricate auger hanger bearings and auger chain case bearings daily.
Lubricate bearings located on machine rear with high temperature grease.
Warnings
! WARNING
disconnected.
W-1023
Lubricate Conveyor Idler and Headshaft Bearings

1� Lubricate (2) auger hanger
bearings with 4 shots of high
temperature grease while hot.
Auger Chain Case

Bearing
2� Lubricate (2) auger chain case

bearings with 3 shots of high Auger Hanger
temperature grease while hot. Bearing

5.03.09 Check Hydraulic Tank Oil Levels

Check cold hydraulic tank oil levels daily.
Warnings
! WARNING
disconnected.
NEVER allow oil levels to fall below indicator line
which can damage the hydraulic system.
NEVER use hands to locate hydraulic leaks - use
cardboard. Oil is under pressure and may cause
severe damage to tissues.
NEVER weld or cut on tank.
NEVER
pressure and may damage components.
W-1024
Lubricate Hydraulic Tank Oil Levels

1� Check hydraulic tank oil levels using sight
gauge located on tank.
2� Add hydraulic oil ISO Vis. Grade 46 anti-wear

or equivalent.
IMPORTANT! Normal operating temperatures

range from 120o-180o F (49o-82o C). Maintain
oil levels above half-way point on sight gauge


5.04 50 Hours Maintenance


5.04.01 Check/Replace Engine Air Intake Filter

50 hours of operation�
Replace element immediately when holes, loose end seals, dented sealing surfaces and damage are
discovered.
Warnings
! DANGER
ALWAYS engage hood service pins when working
under hood.
disconnected.
D-1114
1� TO CHECK FILTER
Check engine air cleaner restriction gauge Remove Cover to
located on machine left side. Change Restriction Gauge
Access Filter
needed.
2� TO REPLACE FILTER
Raise the engine compartment hood.
3� Engage hood raise service pins.
4� Remove air inlet box.
5� Pull cover and elements straight from housing

to avoid damaging the elements.
6� Install
7� Reinstall
IMPORTANT!
assembly.

5.04.02 Change Hydraulic Filters

FIRST 50 hours of operation, then every 250 hours thereafter.
located inside the engine compartment.
Warnings
! WARNING
disconnected.
W-1025
Change Hydraulic Filters

1� Ensure oil temperature is below 100°F (38°C).
2� Clean
heads.
3� Remove
4� Fill
5� Lubricate
oil.
6� Install
manufacturer.
7� Tighten
8� Start the engine and check for leaks.

IMPORTANT! Never check for leaks using
hands or any other body part to avoid serious
injury and death.

5.04.03 Check/Refill Battery Electrolyte Levels

Check battery electrolyte levels every 50 hours of operation.
(2) batteries are located on the left hand side of the machine inside the battery box mounted in
front of the right hand drive tire.
Warnings
! WARNING
disconnected.
NEVER
NEVER
Wear gloves and protective clothing when servicing
batteries.
W-1026
Check/Refill Battery Electrolyte Levels

1� Remove vent well caps to view electrolyte
level.
2� Maintain electrolyte levels at the base of the

vent well.
3� using distilled clean drinking water or

5.04.04 Lubricate Screed Endgate Jacks

Lubricate screed endgate jacks every 50 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Lubricate Screed Endgate Jacks

1� Lubricate (4) screed endgate
jacks located on the machine
rear left side with 2 shots each of Lubrication Points
high temperature grease.

5.04.05 Lubricate Angle of Attack Mechanisms

Lubricate angle of attack mechanism every 50 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Lubricate Angle of Attack Mechanisms

1� Lubricate (6) angle of attack
mechanisms located on the
screed right and left hand
sides with 2 shots each of high Lubrication Points
temperature grease.

5.04.06 Lubricate Angle of Attack Threads

Lubricate angle of attack threads every 50 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Lubricate Angle of Attack Threads

1� Lubricate (2) angle of attack
threads located on the top of the
angle of attack component with a
light coat of never seize.
Threads

5.04.07 Lubricate Screed Crown Threads

Lubricate screed crown threads every 50 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Lubricate Screed Crown Threads

1� Lubricate (2) screed crown
threads located on the screed
crown with a light coat of never
seize.
Threads

5.04.08 Lubricate Strike-off Tube

Lubricate strike-off tube every 50 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Lubricate Strike-off Tube

1� Lubricate (2) strike-off tube
points located on the screed rear
left side with a light coat of never
seize. Grease the length of the
top and sides of the brass tube.
Lubrication Points

5.04.09 Check Tire Pressure

Check tire pressure every 50 hours of operation.
Warnings
! WARNING
disconnected.
NEVER
NEVER
Stand to the side of tire when servicing tire.
W-1028
Check Tire Pressure

1� Check (2) tires with tire valve
positioned at 12 o’clock using
pressure gauge. Depress valve Position tire
to release water that might be valve at 12
o’clock
contain a water ballast. Ensure
2� Check for any damage,

punctures, wear or air bubbles.
Ensure wheel lug nuts are
tightened.
3� tires if needed.

5.04.10 Lubricate Crown Control

Lubricate screed crown control every 50 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Lubricate Crown Control

1� Lubricate screed crown control
at (4) points with 2 shots of high
temperature grease.
Lubrication Points



5.05.01 Change Engine Oil and Oil Filter

FIRST 100 hours of operation, then
every 250 hours thereafter.
Use API CJ-4 (ACEA E9) diesel engine oil when the ambient temperature is above 0°F (-18°C) and
below 104°F (40°C). Refer to the engine operation and maintenance manual for more information
Warnings
! WARNING
disconnected.
W-1027
Change Engine Oil

1� Start engine and run until
engine reaches operation
temperature.
2� Locate remote engine oil drain

hose located behind the right
hand engine access door.
3� Remove plug from drain

hose. Drain all oil into suitable Engine Oil Drain
container.

Change Engine Filter

4� Clean dirt and debris from
5� Remove
6� Fill
engine oil.
7� Apply
8� Install
the manufacturer.
IMPORTANT! Never
prevent damage to the threads
9� Reinstall the oil drain plug.
10� Fill the engine with the

required amount of clean
engine oil. (API CJ-4).
11� Start engine and run at idle.
12� Inspect
and drain plug.
13� Shut the engine off, wait 10

minutes, and check the oil
levels using the dipstick to
ensure oil levels fall between
the ADD and FULL marks.



5.06.01 Check/Replace Engine Air Intake Filter

250 hours of operation.
Replace element immediately when holes, loose end seals, dented sealing surfaces or damage are
discovered.
Warnings
! DANGER
ALWAYS engage hood service pins when working
under hood.
disconnected.
D-1114
Check/Replace Engine Air Intake Filter

TO CHECK FILTER
1� Check engine air cleaner
restriction gauge located on
needed.
TO REPLACE FILTER
2� Raise the engine compartment
hood.
4� Remove air inlet box.
5� Pull cover and elements straight

from housing to avoid damaging
the elements.
6� Install the new inner and outer
7� Reinstall
IMPORTANT! Never remove the

5.06.02 Change Engine Oil and Oil Filter

Use API CJ-4 (ACEA E9) diesel engine oil when the ambient temperature is above 0o F (-18o C)
and below 104o F (40o C). Refer to the engine operation and maintenance manual for more
Warnings
! WARNING
disconnected.
W-1027
Change Engine Oil

1� Start engine and run until
engine reaches operation
temperature.
2� Locate remote engine oil drain

hose located behind the right
hand engine access door.
3� Remove plug from drain

hose. Drain all oil into suitable Engine Oil Drain
container.

Change Engine Filter

1� Clean dirt and debris from
2� Remove
3� Fill
engine oil.
4� Apply
5� Install
the manufacturer.
IMPORTANT! Never
prevent damage to the threads
6� Reinstall the oil drain plug.
7� Fill the engine with the

required amount of clean
engine oil. (API CJ-4).
8� Start engine and run at idle.
9� Inspect
and drain plug.
10� Shut the engine off, wait 10

minutes, and check the oil
levels using the dipstick to
ensure oil levels fall between
the ADD and FULL marks.

5.06.03 Change Engine Fuel Filter

Warnings
! WARNING
disconnected.
W-1027
Change Engine Fuel Filters

CHANGE FUEL FILTERS
1� Remove
2� Fill
fuel and lubricate the seals.
3� Start the engine and check for

leaks. Fuel Filter
DRAIN AND CHANGE FUEL/

WATER SEPARATOR FILTER
1� Open the valve and drain all
water collected in the reservoir
on a DAILY basis.
Fuel/Water Separator
2� Remove the element and replace Filter Valve
with a clean, new element.

5.06.04 Change Hydraulic Filters

located inside the engine compartment.
Warnings
! WARNING
disconnected.
W-1025
Change Hydraulic Filters

1� Ensure oil temperature is below 100°F (38°C).
2� Clean
heads.
3� Remove
4� Fill
5� Lubricate
oil.
6� Install
manufacturer.
7� Tighten
8� Start the engine and check for leaks.

IMPORTANT! Never check for leaks using
hands or any other body part to avoid serious
injury and death.

5.06.05 Change Wheel Planetary Oil

Change wheel planetary oil after every 250 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Change Wheel Planetary Oil

1� Position machine on a
completely level surface.
2� Clean dirt and grease from
around the port plugs.
9 o’clock position
3� Move machine forward until both
ports are positioned at the 6
o’clock position and the 9 o’clock
position as shown.
4� Remove the port plugs from the
port positioned at 6 o’clock and
drain gear oil.
5� Dispose of gear oil in safe and
legal manner.
6� Reinstall the port plug
positioned at 6 o’clock.
7� the hub with 80w-140 high
performance gear oil through the
port in the 9 o’clock position until 6 o’clock position
port.
8� Reinstall the port plug at the 9
o’clock position.

5.06.06 Change Pump Drive Gearbox Oil

Change pump drive gearbox oil after every 250 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Change Pump Drive Gearbox Oil

1� Remove the drain plug from the
pump drive drain hose.
Gear Drive Drain
2� Drain oil into appropriate

container. Dispose of the
container in a legal and safe
manner.
3� Reinstall drain plug.
Pump Drive
4� the pump drive with 3-5

quarts (2.84-4.73 liters) of
80w-140 high performance gear
oil.
IMPORTANT! Always check
oil levels using dip stick. Never
gearbox to avoid damage.

5.06.07 Change Auger and Conveyor Planetary Oil

Change (2) auger and (2) conveyor planetary oil after every 250 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Change Auger and Conveyor Planetary Oil

1� Remove the bottom port plug
and drain the gear oil. Dispose
of gear oil in a legal and safe
manner.
2� Reinstall the drain plug.

Fill Port
Check Port
3� Remove
4� Add 80w-140 high performance
oil begins to seep out of the

check port.
5� Reinstall
port plugs.
Drain Port

5.06.08 Lubricate Seat Pivot Bearing

Lubricate seat pivot bearing with 2 shots high temperature grease every 250 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Lubricate Seat Pivot Bearing

1� Lubricate
high temperature grease.




5.07.01 Flush and Clean Radiator

1,000 hours of operation.
Warnings
! WARNING
NEVER perform service or
maintenance until machine is shut
down and batteries are disconnected.
removing cap. Stand to the side and

away from cap during removal.
W-1029
Flush and Clean Radiator

1� Open drain valve and allow
coolant to drain.
2� Check radiator for mineral

build-up, rust or oil.
3� Flush out all contaminants with

radiator cleanser.
4� Flush radiator with clean water.
5� with 50/50 anti-freeze and

water.
6� Top off with 1 liter of Cummins

supplemental coolant additive.
IMPORTANT! Maintain engine
coolant levels to 4 inches from
bottom of cap. Check sight class

5.07.02 Replace Engine Breather

Check engine breather every 1,000 hours of operation.
Replace element immediately when holes, loose end seals, dented sealing surfaces and damage are
discovered.
Warnings
! WARNING
disconnected.
Engage hood service pins when working under
hood.
W-1030
Replace Engine Breather

1� Raise the engine compartment
hood.
3� Remove
4� Pull cover and elements straight

from housing to avoid damaging
the elements.
5� Install the new inner and out
6� Reinstall
cover.
IMPORTANT! Never remove the

5.07.03 Flush Hydraulic Tank and Replace Strainer

Warnings
! WARNING
disconnected.
NEVER allow oil levels to fall below indicator line
which can damage the hydraulic system.
NEVER weld or cut on tank.
NEVER
pressure and may damage components.
W-1024
Drain and Flush Hydraulic Tank

1� Clean dirt and grease from around tank
plug.
2� Remove plug from the hydraulic drain hose.
3� Drain
safe manner.

4� Remove and clean tank strainers. Replace if

needed.
5� Remove
6� Clean tank thoroughly, vacuuming any

particles from the bottom of the tank using a
shop vacuum.
Refill Hydraulic Tank

7� Reinstall drain plugs and strainers.
8� Replace
4.04.02.
9� Fill tank to 90% capacity (68.4 gal. or 259 l)
through a 10-micron element.

IMPORTANT!

5.07.04 Flush and Refill Wheel Planetary Oil

Change wheel planetary oil after every 1,000 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Flush and Refill Wheel Planetary Oil

1� Position machine on a
completely level surface.
2� Clean dirt and grease from
around the port plugs.
9 o’clock position
3� Move machine forward until both
ports are positioned at the 6
o’clock position and the 9 o’clock
position as shown.
4� Remove the port plugs from the
port positioned at 6 o’clock and
drain gear oil.
5� Dispose of gear oil in safe and
legal manner.
6� Reinstall the port plug
positioned at 6 o’clock.
7� the hub with 80w-140 high
performance gear oil through the
port in the 9 o’clock position until 6 o’clock position
port.
8� Reinstall the port plug at the 9
o’clock position.

5.07.05 Flush and Refill Pump Drive Gearbox Oil

Change pump drive gearbox oil after every 1,000 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Flush and Refill Pump Drive Gearbox Oil

1� Remove the drain plug from the
pump drive drain hose.
Gear Drive Drain
2� Drain oil into appropriate

container. Dispose of the
container in a legal and safe
manner.
3� Reinstall drain plug.
Pump Drive
4� the pump drive with 3-5

quarts (2.84-4.73 liters) of
80w-140 high performance gear
oil.
IMPORTANT! Always check
oil levels using dip stick. Never
gearbox to avoid damage.

5.07.06 Flush and Refill Auger and Conveyor Planetary Oil

Change (2) auger and (2) conveyor planetary oil after every 1,000 hours of operation.
Warnings
! WARNING
disconnected.
W-1027
Flush and Refill Auger and Conveyor Planetary Oil

1� Remove the bottom port plug
and drain the gear oil. Dispose
of gear oil in a legal and safe
manner.
2� Reinstall the drain plug.

Fill Port
Check Port
3� Remove
4� Add 80w-140 high performance
oil begins to seep out of the

check port.
5� Reinstall
port plugs.
Drain Port

5.07.07 Check and Refill Bogie Wheel Bearings

Warnings
! WARNING
disconnected.
W-1027
Check and Refill Bogie Wheel Bearings

1� Jack up one side of the paver
at a time just high enough to
remove the bogie wheels.
2� Remove the retaining cap that

exposes the retaining nut.
3� Remove the retaining nut and

remove the wheel.
4� Remove both the inner and

outer bearing from inside the
wheel.
5� Replace any damaged bearings.
6� Pack all bearings with high

temperature NLGI grade 2 grease
only.
7� Mount the wheel back onto the

bogie. Secure with retaining nut.
8� Reinstall the retaining cap.
9� Repeat process with opposite

side of paver.



5.08.01 Diesel Emissions Fluid Filters

2,000 hours of
operation.
Warnings
! WARNING
disconnected.
W-1027
Change Diesel Emissions Fluid Filters

1� Change
Filter in Tank
2� Unscrew
Unscrew
Cartridge


5.09 Maintenance Procedures


5.09.01 Machine Lifting Points

Lifting points are located on the front and rear of the machine. Use cables rated at 20 tonnes.
Lifting Points
Rear Lifting Points

Front Lifting Points

5.09.02 Machine Tie Down Points

Tie down points are located on the front and rear of the machine.
Tie Down Points
Front Tie Down Rear Tie Down

Points Points

5.09.03 Adjust Auger Drive Chain

Check auger chain once a week. Adjust when needed or when auger chain under- performs.
Warnings
! WARNING
disconnected.
W-1027
Adjust Auger Drive Chain

1� Check the range of movement
in the chain by twisting the
auger shaft back and forth.
Adjust the chain if there is
more than 1/2” movement.

2� Loosen (4) auger drive

mounting bolts using a 3/4”
hex wrench.
IMPORTANT! DO NOT
completely remove bolts.
3� Adjust the tension by

tightening the chain tension
bolts with a 1” wrench. Tighten
each chain until there is less
than 1/2” movement in each
auger shaft.

4� Tighten auger drive mounting

bolts to secure.
5� Purge auger chain case

bearings daily while they are
hot using high temperature Auger Chain Case
grease. Bearing
Auger Hanger
Bearing

5.09.04 Adjust Conveyor Drive Chain

Check conveyor drive chain once a week. Adjust when needed or when conveyor chain under-
performs.
Warnings
! WARNING
disconnected.
W-1027
Adjust Conveyor Drive Chain

IMPORTANT! NEVER adjust
drive chain while hot. Tension
will increase when chains have
cooled. Securing Bolts
1� Inspect (2) conveyor drive

chains to determine slack or
movement.
2� Adjust tension if more than 1/2”

of movement exists.
3� Loosen (2) chain drive chain

securing bolts. Tensioning
Adjustment Bolt
4� Tighten chain tension

adjustment bolt until there is
1/2” or less movement in drive
chain.
5� Tighten chain drive securing

bolts to maintain tension.

5.09.05 Adjust Conveyor Drag Chain

Check conveyor drag chain once a week. Adjust when needed or when conveyor chain under-
performs.
Warnings
! WARNING
disconnected.
W-1027
Adjust Conveyor Drag Chain

IMPORTANT! NEVER adjust
drag chains while hot. Tension
will increase when chains have
cooled.
1� Inspect (2) conveyor drag

chains under machine to
determine slack or movement.
2� Adjust tension if more than 1/2”

of movement exists.
Conveyor Drag
chains
3� Loosen lock nuts on drag chain

adjustment bolts located at the
front of the hopper.
4� Apply tension to both tensioner

bolts evenly until there is less
than 1/2” sag in both sides of the
drag chain.
5� Tighten lock nuts.

Drag chain
adjustment bolts

5.09.06 Wash Down Machine

Wash down machine at the end of each work day prior to greasing procedures while the asphalt
material and the machine are still warm. The wash down system utilizes environmentally-friendly
solvent to help remove asphalt and dirt from the machine.
Warnings
! WARNING NOTICE
Avoid serious injury or death! Check local, state and federal regulations for
oil waste material handling procedures. NEVER
NEVER leave solvent on walkways or stairs. Take
spray diesel on wheels. Degradation of rubber
care when climbing on or off machine during
will lead to premature failure.
procedure.
W-1031 N-1029
Wash Down Machine

1� Locate the wash down system
switch on the right side of the
machine.
2� Position machine where

solvent and residue will not
affect the paving operation or
the environment.
3� Raise screed, then secure with

service cables.
4� Run engine in low idle.
5� Clear personnel of the area.
Wash down hose

ON/OFF
6� Set Parking Brake.
7� Turn right and left conveyor

systems ON.
8� Point wash down sprayer

in safe direction away from
persons.
9� Activate spray system with the

switch located next to the hose
reel on the screed.

10� Wash down:

Push Rollers until they turn
freely.
Conveyor chains and bars while

rotating, rear conveyor drive
sockets while rotating, auger
rotating, screed walkways,

steps, and screed bottom,
end gates ensuring they slide
properly, hydraulic strike-offs
between strike-offs and screed.
IMPORTANT! The wash

down system is located on the
screed. Check the site glass
located on the screed near the
is located on machine hood.

5.09.07 Manual Hood Raise and Brake Release

Raise or lower the machine hood and release parking brakes without the engine running.
Warnings
! WARNING
procedure.
ALWAYS reset manual overrides to locked
position to avoid release of parking brakes and
hood movement.
W-1032
Manual Hood Raise and Brake Release

1� Locate the manual hand pump
located beneath the left hand
RAISE HOOD
2� Remove protective cap.
Turn override screw counter
clockwise until it stops in the
UP position to activate manual
override.
3� Insert provided handle into the

hand pump.
4� Pump using handle until hood

is completely raised.
5� Install lock pin into hood

prop to secure hood in raised
position.
6� Reset manual override

by turning override screw
DOWN position.
7� Replace protective cap.
IMPORTANT! Reverse
instructions to LOWER HOOD
using Hood Lower override
screw.

RELEASE PARKING BRAKES

9� Turn parking override screw

counter clockwise until it stops
in the UP position to activate
manual override.
10� Insert provided handle into

hand pump.
11� Pump until handle provides

strong resistance.
12� Turn brake ball valve clockwise

to close and release brakes.
13� Reset manual override

by turning override screw
DOWN position.
IMPORTANT! Reverse the

steps above to apply parking
brakes.

5.09.08 Engage / Disengage Propel Pump Bypass

Engage or disengage the propel pump bypass.
Warnings
! WARNING
disconnected.
W-1027
Engage / Disengage the Propel Pump Bypass

1� Turn middle hex nut 3 turns
counter clockwise relative to the
larger hex nut to engage bypass
feature of the multi-function
valves on the propel pump.
2� Turn middle hex nut clockwise Multi-function

until tightened to disengage valves
the bypass feature of the multi-
function valves on the propel
pump.

5.09.09 Pivot Seats with Manual Hand Pump

Pivot seats using the manual hand pump.
Warnings
! WARNING
ALWAYS reset manual overrides to locked position
to avoid unintentional seat pivoting when auxiliary
pressure is restored.
procedure.
W-1033
Pivot Seats with Manual Hand Pump

1� Remove lock pin from hood
prop.
Left Hand Seat
3� Turn override screw counter

UP position to activate manual Right Hand Seat
override.
4� Push or Pull override while

turning to lock left or right seat
pivot valve.
UP/DOWN = valve enters bypass
mode and is able to be manually
actuated to pivot corresponding
operator seat.
CENTER = valve in normal
operating mode.
5� Insert provided handle into hand

pump.
6� Pump until seat is in desired

position.
7� Reset manual override on hand
override screw clockwise until it

stops in the DOWN position.
8� Replace protective cap.

5.10 Wear Parts Guide
Winter Check List
New Replace
Floor Plates 3/8” thick 3/16” thick
All Sprockets Are hardened 1/8” of an inch
Delta Plate Starts 3/8” thick 1/8” thick
Tee Pee/Center Guard 3-1/2” wide 3” wide
Guards Outside 3-7/8” wide 3-3/8” wide
Auger Segments 6” 4”
Chains See chart
EZ IV Screed Plates 1/2” thick 3/16” thick
Angle of Attack Screws 1/16” of vertical play 1/4” of vertical play
Endgate Shoes 1/2” thick 3/16” thick

5.11 Chain Wear Guide


Hydraulic Systems
6.0 Hydraulic Systems

Hydraulic Systems

Hydraulic Systems
6.01 Hydraulic Pump Drive System
Hydraulic Pump Drive System
Pump Drive
Conveyor Pump
Propel Pump
Screed Heat Pump

Auxiliary Pump
Auxiliary Pump
Sauer Danfoss Series 45 pressure compensated pump provides Hydraulic power to auxiliary systems
including hopper wings, tow arm cylinders and hood lift.
Propel Pumps
Sauer Danfoss Series 42 pumps with relief pressure set at 4714 psi and charge pressure of 348 psi
provide power to the Left Hand and Right Hand Propel Systems.
Conveyor Pumps
Sauer Danfoss Series 40 pumps with pressure relief set at 4060 psi and charge pressure at 283 psi
provide power to Left Hand and Right Hand Conveyors.
Screed Heat Pump
Sauer Danfoss 75cc load sense pump has a max system pressure setting at 4600 psi and provides
power to the screed for paving and accessories.

Hydraulic Systems

Hydraulic Systems
6.01.01 Auxiliary Pump

Auxiliary Pump
Sauer Danfoss, J Frame,
S45 pump, open circuit Aux Pump Case
60 CC Drain to Tank
Pressure compensator Manifold
150 Bar (2175 psi)
Aux Pump to
Aux Pump Suction
Aux Filter
to Hydraulic Tank

Hydraulic Systems
6.01.02 Propel Pumps

Propel Pumps
Sauer Danfoss, S42
pump, 22.8 CC, EDC
Diff Lock
Inlet
Charge

Hydraulic Systems
6.01.03 Conveyor Pumps

Conveyor Pumps
Sauer Danfoss, S40
pump, EDC, CCW
Rotation
Suction
From Tank
Case
Drain
Charge
Charge Pressure in
Pressure out From Filter
to Filter

Hydraulic Systems
6.01.04 Screed Generator Pump

Screed Generator Pump
Sauer Danfoss Load
Heat Pump
Sense, S45 F-Frame,
Case Drain to
74CC, Pressure
Tank Manifold
Compensator setting
310 Bar (4495 psi)
Heat Pump
Suction to Tank
Test Port

Hydraulic Systems
6.01.05 Radiator Fan Pump

Radiator Fan Pump
Sauer Danfoss Load
Sense, S45 Pump,
Pressure Compensated
Test Port
Port S Charge
Port L1 Case Port B Pressure From Tank
Drain to Tank to Inlet on
Cooler

Hydraulic Systems

Hydraulic Systems
6.02 Motors

Hydraulic Systems

Hydraulic Systems
6.02.01 Auger and Conveyor Motors

Auger and Conveyor Motors
Auger Drive
Planetary Auger Drive Motor
Conveyor Drive Conveyor Drive

Motor Planetary

Hydraulic Systems
6.02.02 Propel Drive Motors

Propel Drive Motor
Sauer Danfoss Series H1 variable motors set for 110 cc max - 22 cc min. range.

Hydraulic Systems
6.02.03 Fume Extraction Motors

Fume Extraction Motor
Sauer Danfoss 1.03 cid motor at 2,765 RPM
Auger Drive
Motor

Hydraulic Systems
6.02.04 Radiator Fan Motor

Radiator Fan Motor
Radiator Fan
Motor

Hydraulic Systems
6.03 Valves

Hydraulic Systems

Hydraulic Systems
6.03.01 Brake Shift, Hood Valve Stack

Brake Shift, Hood Valve Stack
2
1 3
4 5
6
1. Manual Hand Pump

2. Hand Pump Flow Out (Console Pivot)
3. Hood Raise
4. Hood Lower
5. Parking Brake
6. Propel Motor
7. Parking Brake Ball Valve (shown in “Closed” position)

Hydraulic Systems
6.03.02 Rear Valve Stack

Rear Valve Stack
1 2 3 4 5
7
1. LH Auger Down/Up
2. RH Auger Down/Up
3. LH Seat Pivot
4. RH Seat Pivot
5. Fume Exhaust with Flow Control
6. Screed Float
7. Screed Raise/Lower

Hydraulic Systems
6.03.03 Tow Point Valves

Right Hand Side Tow Point Valve
1 2
Left Hand Side Tow Point Valve
1. Right Hand Tow Point

2. Hopper Wing
3. Left Hand Tow Point
4. Truck Hitch

Hydraulic Systems
6.03.04 Differential Lock Valve

Differential Lock Valve

Hydraulic Systems
6.03.05 Screed Assist/Screed Boost Valve

Screed Assist/Screed Boost Valve

Hydraulic Systems
6.03.06 Hydraulic Tunnel Extension Valve

Hydraulic Tunnel Extension Valve

Maintenance Charts
7.0 Maintenance Charts

Maintenance Charts

Maintenance Charts
7.01 Daily Maintenance Chart
IDENTIFICATION SERVICE REMARKS

Engine Crankcase Check Refer to Engine Manual
Engine Oil Check Level Refer to Engine Manual
Diesel Fuel
Diesel Exhaust Fluid

22241-01
Radiator Check level

antifreeze and water
Conveyor Idler Bearings Lubricate with high temp.

grease
Vibrator Bearings Lubricate with high temp.

grease
Conveyor Headshaft Lubricate with high temp. Purge while hot and running
Bearings grease
Auger Hanger Bearings Lubricate with high temp. Purge while hot
grease
Auger Chain Case Bearings Lubricate with high temp. Purge while hot and running
grease
Hydraulic Tank Check Oil Level

grade 46 hydraulic oil

Maintenance Charts
7.02 50 Hour Maintenance
DATE IDENTIFICATION SERVICE REMARKS

Engine Air Filter Check Replace if in bad
repair
Batteries Check electrolyte level
Tire Pressure Check pressure Do not exceed 38 psi
Screed Endgate Jacks Lubricate with high 2 shots each grease

temp. grease
Angle of Attack Mechanism Lubricate with high 2 shots each grease

temp. grease
Angle of Attack Threads Lubricate with Apply light coat

Never-Seize of Never-Seize to
threads
Screed Crown Threads Lubricate with Apply light coat

Never-Seize of Never-Seize to
threads
Strike-Off Tube Lubricate with high Apply light coat of

temp. grease high temp. grease
Crown Control Lubricate with high 2 shots each grease

temp. grease
Hydraulic Filters Change

50 hours of operation
on a new machine.

Maintenance Charts

Engine Oil and Filter Replace

Maintenance Charts

Engine Air Filters Check Replace if needed
Hydraulic Filters Replace
Engine Oil and Filters Replace
Engine Fuel Filter Replace
Wheel Planetary Check, Flush, Drain,
Pump Drive Gearbox Check, Flush, Drain,
Auger Planetary Check, Flush, Drain,
Conveyor Planetary Check, Flush, Drain,
Seat Pivot Bearing Lubricate with High 2 shots each grease

Temp. grease

Maintenance Charts

Hydraulic Tank
With Grade 46
Hydraulic Oil
Hydraulic Tank Strainer Replace Replace In-Tank
Hydraulic Filter
Wheel Drive Planetary

140 Synthetic Gear Oil
Radiator 50/50 mix of water

and anti-freeze
Pump Drive Gearbox

(2.84-4.73) 80w-140
Breather Replace Replace
Auger Planetary
Conveyor Planetary
Bogie Wheel Bearings

high temperature
grease

Maintenance Charts

Diesel Emissions Fluid Filters Replace Change after 2000 hours
of operation.

Troubleshooting
8.0 Troubleshooting

Troubleshooting

Troubleshooting
8.01 Engine Diagnostic Screen

Displays engine Error Code Messages (ECM) when engine malfunctions. ECM indicates malfunction
using engine codes.
Engine Diagnostic Screen
Press Request Fault Codes from the Menu Options Screen on the digital display.
The store fault codes screen appears. Press the up and down buttons to scroll through all fault codes.
Active codes and stored codes can be cleared from this screen by pressing the corresponding command.

Troubleshooting
Engine Diagnostic Screen
The Society of Automotive Engineers established an exact listing of SPN and FMI codes that are
universally used by all engine manufacturers.
ECM indicates the engine malfunction using engine codes.
1) SPN - Suspect Parameter Number indicates the system or component with failure�
based on an average value system�
SPN 110, FMI 03 indicates the failure of an engine coolant temperature circuit with an above average
temperature.
The following pages chart the engine fault codes for reference.

Troubleshooting
8.01.01 Engine Fault Codes
SPN FMI Description

29 3 Remote Accelerator Pedal Position Sensor-Shorted High
29 4 Remote Accelerator Pedal Position Sensor-Shorted Low
84 2 Vehicle Speed Sensor Circuit-Data Incorrect
84 10 Vehicle Speed Sensor Circuit-Tampering Has Been Detected
91 3 Accelerator Pedal Position Sensor Circuit-Shorted High
91 4 Accelerator Pedal Position Sensor Circuit-Shorted Low
91 8 Accelerator Pedal Position Sensor Circuit-Low Frequency
91 8 Accelerator Pedal Position Sensor Circuit-High Frequency
91 19 SAE J1939 Multiplexing Accelerator Pedal Sensor System Error
91 2 Accelerator Pedal Idle Validation Circuit - Data Incorrect
91 13 Accelerator Pedal Idle Validation Circuit-Out Of Calibration
91 4 Accelerator Pedal Idle Validation Circuit - Shorted Low
93 2 OEM Alternate Torque Validation Switch-Data Incorrect
94 16 Fuel Pressure High - Warning
94 18 Fuel Pressure Low - Warning
94 3 Fuel Delivery Pressure Sensor Circuit-Shorted High
94 4 Fuel Delivery Pressure Sensor Circuit-Shorted Low
97 15 Water In Fuel Indicator High - Maintenance
97 3 Water In Fuel Sensor Circuit - Shorted High
97 4 Water In Fuel Sensor Circuit - Shorted Low
100 3 Engine Oil Pressure Sensor Circuit-Shorted High
100 4 Engine Oil Pressure Sensor Circuit-Shorted Low
100 18 Engine Oil Pressure Low-Warning
100 1 Engine Oil Pressure Low-Warning
100 1 Engine Oil Pressure Low - Critical
100 2 Engine Oil Pressure Sensor Circuit - Data Incorrect
102 3 Intake Manifold Pressure Sensor #1 Circuit-Shorted High
102 4 Intake Manifold Pressure Sensor #1 Circuit-Shorted Low
102 2 Intake Manifold Pressure Sensor Circuit-Data Incorrect
103 16 Turbo Charger #1 Speed High - Warning Level
105 3 Intake Manifold Temperature Sensor #1-Shorted High
105 4 Intake Manifold Temperature Sensor #1-Shorted Low
105 0 Intake Manifold Temperature #1 High-Critical
108 3 Ambient Air Pressure Sensor Circuit-Shorted High
108 4 Ambient Air Pressure Sensor Circuit-Shorted Low
108 2 Ambient Air Pressure Sensor Circuit-Data Incorrect
109 3 Engine Coolant Pressure Sensor Circuit-Shorted High
109 4 Engine Coolant Pressure Sensor Circuit-Shorted Low
109 1 Engine Coolant Pressure Low-Warning
110 3 Engine Coolant Temperature Sensor Circuit-Shorted High

Troubleshooting
SPN FMI Description

110 4 Engine Coolant Temperature Sensor Circuit-Shorted Low
110 0 Engine Coolant Temperature High-Critical
111 1 Engine Coolant Level Low-Critical
111 2 Engine Coolant Level Sensor Circuit-Data Incorrect
135 3 Fuel Pump Delivery Pressure Sensor Circuit-Shorted High
135 4 Fuel Pump Delivery Pressure Sensor Circuit-Shorted Low
156 3 Fuel Timing Pressure Sensor Circuit -Shorted High
156 4 Fuel Timing Pressure Sensor Circuit -Shorted Low
156 2 Fuel Timing Pressure Or Timing Actuator Stuck
157 3 Injector Metering Rail #1 Pressure Sensor Circuit - Shorted High
157 4 Injector Metering Rail #1 Pressure Sensor Circuit - Shorted Low
157 16 Injector Metering Rail #1 Pressure High-Warning Level
157 0 Injector Metering Rail #1 Pressure High-Warning Level
157 2 Fuel Pressure Sensor Error
166 2 Cylinder Power Imbalance Between Cylinders
167 16 Electrical Charging System Voltage High - Warning Level
167 18 Electrical Charging System Voltage Low - Warning Level
167 1 Electrical Charging System Voltage Low - Critical Level
168 18 Battery #1 Voltage Low - Warning
168 1 Battery #1 Voltage Low - Warning
168 16 Battery #1 Voltage High - Warning
168 0 Battery #1 Voltage High - Warning
174 0 Fuel Temperature High-Warning
174 3 Fuel Temperature Sensor Circuit-Shorted High
174 4 Fuel Temperature Sensor Circuit-Shorted Low
175 3 Engine Oil Temperature Circuit-Shorted High
175 4 Engine Oil Temperature Circuit-Shorted Low
175 0 Engine Oil Temperature High-Critical
190 2 Engine Speed/Position Sensor Circuit Lost Both Of Two Signals From Magnetic
Pickup Sensor
190 10 Engine Speed/Position Sensor Circuit Lost Both Of Two Signals From Magnetic
Pickup Sensor
190 0 Engine Speed High-Critical
191 16 Transmission Output Shaft (Tailshaft) Speed High-Warning
191 0 Transmission Output Shaft (Tailshaft) Speed High-Warning
191 18 Transmission Output Shaft (Tailshaft) Speed Low-Warning
191 1 Transmission Output Shaft (Aux Gov) Speed Low-Warning
251 2 Real Time Clock-Power Interrupt
558 2 Accelerator Pedal Idle Validation Circuit - Data Incorrect
558 13 Accelerator Pedal Idle Validation Circuit-Out Of Calibration
558 4 Accelerator Pedal Idle Validation Circuit - Shorted Low
620 4 Sensor Supply Voltage #2 Circuit-Shorted Low
620 3 Sensor Supply Voltage #2 Circuit-Shorted High

Troubleshooting
SPN FMI Description

626 11 Start Assist Device Control Circuit Error (Ether Injection)
626 1 Start Assist Device-Canister Empty (Ether Injection)
627 2 Power Lost Without Ignition Off
629 12 Engine Control Module-Critical Internal Failure
629 12 Engine Control Module-Warning Internal Hardware Failure
630 2 Engine Control Module-Data Lost
630 12 Engine Control Module-Warning Software Error
632 4 Fuel Shutoff Valve Circuit-Shorted Low
632 3 Fuel Shutoff Valve Circuit-Shorted High
632 7 Fuel Shutoff Valve-Stuck Open
633 5 Fueling Actuator #1 Circuit-Open Circuit
633 6 Fueling Actuator #1 Circuit-Grounded Circuit
633 3 Fuel Control Valve Circuit - Shorted High
633 2 Fuel Rail Actuator Circuit - Data Incorrect
633 7 Fuel Control Valve - Mechanically Stuck
635 7 Engine Timing Actuator Is Not Responding To ECM Commands
635 3 Engine Timing Actuator Circuit-Shorted High
635 5 Timing Actuator #1 Circuit - Open Circuit
635 6 Timing Actuator #1 Circuit - Grounded Circuit
635 2 Timing Actuator Circuit - Data Incorrect
639 9 SAE J1939 Multiplexing PGN Timeout Error
639 13
639 2 SAE J1939 Datalink - Cannot Transmit
639 9 SAE J1939 Not Fast Enough
644 2 External Speed Input (Multiple Unit Synchronization) - Data Incorrect
647 4 Fan Clutch Circuit-Shorted Low
651 6 Injector Solenoid Valve Cylinder #1 Circuit-Grounded Circuit
702 3 Auxiliary Input/Output #2 Circuit - Shorted High
703 3 Auxiliary Input/Output #3 Circuit - Shorted High
723 2 Engine Speed/Position #2 - Cam Sync Error
931 3 Fuel Supply Pump Actuator Circuit-Shorted High
931 7 Fuel Supply Pump Actuator-Mechanically Stuck
974 3 Remote Accelerator Pedal Position Sensor-Shorted High
974 4 Remote Accelerator Pedal Position Sensor-Shorted Low
974 19 SAE J1939 Multiplexing Remote Throttle Data Error
1043 4 Engine Speed/Position Sensor #1 (Crankshaft) Supply Voltage Circuit-Shorted Low
1043 3 Accelerator Pedal Position Sensor Supply Voltage Circuit - Shorted High
1043 4 Accelerator Pedal Position Sensor Supply Voltage Circuit - Shorted Low

Troubleshooting
SPN FMI Description

1043 11 Engine Speed/Position Sensor #2 (Camshaft) Voltage Supply
1079 4 Sensor Supply Voltage #1 Circuit-Shorted Low
1079 3 Sensor Supply Voltage #1 Circuit-Shorted High
1083 14 Auxiliary Temperature Sensor Input #1 Engine Protection-Critical
1083 3 Auxiliary Temperature Sensor Input #1 Circuit-Shorted High
1083 4 Auxiliary Temperature Sensor Input #1 Circuit-Shorted Low
1084 14 Auxiliary Pressure Sensor Input #2 Engine Protection-Critical
1084 3 Auxiliary Pressure Sensor Input #2 Circuit-Shorted High
1084 4 Auxiliary Pressure Sensor Input #2 Circuit-Shorted Low
1188 4 Turbo Charger #1 Wastegate Control Circuit-Shorted Low
1244 5 Fueling Actuator #2 Circuit - Open Circuit
1244 6 Fueling Actuator #2 Circuit - Grounded Circuit
1245 5 Timing Actuator #2 Circuit - Open Circuit
1245 6 Timing Actuator #2 Circuit - Grounded Circuit
1264 0 Engine Blowby - Warning Level
1264 3 Crankcase Blowby Pressure Sensor Circuit - Shorted High
1264 4 Crankcase Blowby Pressure Sensor Circuit - Shorted Low
1265 4 Engine Oil Burn Valve Solenoid Circuit-Shorted Low
1266 4 Engine Oil Replacement Valve Solenoid Circuit-Shorted Low
SPN FMI Description
1349 3 Injector Metering Rail #2 Pressure Sensor Circuit-Shorted High
1349 4 Injector Metering Rail #2 Pressure Sensor Circuit-Shorted Low
1349 16 Injector Metering Rail #2 Pressure High-Warning
1349 18 Injector Metering Rail #2 Pressure Low-Warning
1349 7 Injector Metering Rail #2 Pressure Malfunction
1377 2 Multiple Unit Synchronization Switch Circuit - Data Incorrect
1378 0 Change Lubricating Oil And Filter
1380 17 Low Oil Level In Centinel Makeup Oil Tank
1380 1 Low Oil Level In Centinel Makeup Oil Tank
1381 3 Fuel Supply Pump Inlet Pressure Sensor Circuit - Shorted High
1381 4 Fuel Supply Pump Inlet Pressure Sensor Circuit - Shorted Low
1381 18 Fuel Supply Pump Inlet Pressure Low - Warning Level
1383 31 Engine Hot Shutdown
1384 31 Engine Shutdown Commanded By J1939
1484 31 Additional OEM/Vehicle Diagnostic Codes Have Been Logged

Troubleshooting
8.02 Troubleshoot Engine Malfunctions

PROBLEM CAUSE RESOLUTION
Engine will not start Parking brake OFF. Set parking brake ON.
Joystick not in neutral. Set joystick to neutral.
Feed System ON. ` Feed System OFF.
Battery disconnect switches OFF. Set battery disconnect switches

to on.
E-stops OFF. Set E-stops to ON.
Weak/dead battery. Charge or replace battery.
Faulty ignition switch. Replace.
Faulty starter or starter solenoid. Replace or replace.
Engine turns over but will not No fuel. Add fuel to tank.
start�
No voltage to fuel solenoid. Ensure voltage is 24 volts when
ignition switch is on.
No fuel to injector pump. Check fuel supply system.
Fuel connections loose on injector

pump. connections from fuel tank to
injector pump.
Intake or exhaust system Remove any restrictions.

restricted.
Engine will not shut off� Low idle set too high. Set idle to low.
Electrical wiring fault supplying Repair wiring.

power to fuel solenoid when key
is in OFF position.
Faulty injection pump fuel Check solenoid for defects or

solenoid. foreign material inhibiting proper
operations.
Engine using fumes drawn into Locate and isolate source of

air intake. fumes.

Troubleshooting

Low engine power output� Operation at high altitude. De-rate engine power output for
altitudes above 10,000 feet.
Air intake restricted. Remove restrictions.
Air cleaner element dirty. Clean or replace air cleaner

elements.
Check fuel line for restrictions.
restricted.
Fuel return system restricted. Correct restricted fuel return
system.
Fuel quality poor. Verify by operating with a known
fuel quality.
Fuel transfer pump Replace fuel transfer pump. See
malfunctioning. engine manufacturer manual.
Throttle improperly adjusted. Adjust throttle controls.
Injector malfunctioning. Replace injector. See engine

manufacturers manual.
Engine de-rated due to clogged
DPF.
Low engine oil pressure� Electrical power not being Check fuse.
supplied to gauge.
Incorrect oil level. Check for leaks. Add or drain
engine oil. Check dipstick.
Oil diluted with fuel. Replace fuel injector, fuel transfer

pump and/or injection pump.
Oil diluted with coolant. Contact authorized engine repair
facility.
Incorrect oil specs. Change oil. Check oil specs.
Oil pressure sender or gauge Replace oil pressure sender of

malfunctioning. gauge.
Coolant level too low. Add coolant.

Troubleshooting

Engine coolant temperature
above normal� obstructed. repair or replace.
Collapsed or restricted radiator Inspect hoses. Replace if needed.
hose.
Loose fan drive belt. Check belt tension and tighten if
needed.
Cooling fan shroud damaged or Inspect shroud. Repair, replace or
missing. install as needed.
Incorrect or malfunctioning Check radiator cap. Replace if
radiator cap. needed.
Temperature gauge Repair or replace sender and/or
malfunctioning. gauge.
Thermostat stuck in closed Test thermostat. Replace if
position. needed.
Dirt, scale or rust in cooling Clean cooling system.
system.

Troubleshooting

Troubleshooting
8.03 Troubleshoot Operations

Machine jerks when moving in Fast movement of joystick Move handle slowly when
forward or reverse� control. changing speed and/or direction.
Parking brake not disengaged. Release parking brake. Check for
binding brake cable(s).
Engine speed set too low. Run engine at higher RPM.
until visible in sight gauge.

Air leaking into hydraulic system.
Hydrostatic pump is Repair or replace pump.

malfunctioning.
Machine will not move with Parking brake engaged. Release parking brake.
engine running or moves only
in one direction� Brush rotation control valve is Repair or replace relief valve
bypassing oil at low pressure. cartridge(s).
Damaged hydrostatic pump. Repair or replace hydrostatic
pump.
Damaged hydrostatic motor. Repair or replace hydrostatic
motor.
Service brake engaged. Return joystick to neutral.

Troubleshooting

Troubleshooting
8.04 Troubleshoot Hydraulic Systems

Hydraulic system overheats�
gauge.
Defective temperature gauge. Replace gauge.
Brush drive relief valve set too Adjust relief valve to 2500 psi.
low or defective. Replace if defective.
Excessive ambient air Operate unit at slower ground
temperature and high duty cycle. speed and max engine RPM
during hot weather.
Hydrostatic pump bypass valve Repair or replace.

defective or open.
Worn hydrostatic pump. Repair or replace.
Bearing failure� Chips or other foreign matter in Make sure clean oil is used.
bearings.
and long life of bearings.
Excessive or shock loads. Reduce operating pressure.

Observe maximum rating of
operating pressure.
System excessively hot. See trouble section headed
“system excessively hot.” (heat
breaks down lubricating qualities
of hydraulic oil).
See Roadtec®, Inc. oil
recommendations.

Troubleshooting

Excessive pump noise� Low oil level. Fill reservoir so that surface of oil
is well above end of suction line
during all of work cycle
Wrong oil type. Use good, clean hydraulic oil
having the viscosity in accordance
with Roadtec® recommendations
Air leak in suction line. Air leak Pour hydraulic oil on joints and
around shaft packing. around shaft while listening for
change in sound of operation.
Tighten as required
Make sure suction line is not
piping. plugged with rags or other
foreign material
Air bound pump. Air is locked in pumping chamber
and has no way to escape. Stop
pump immediately! Before
restarting, partially open pressure
line or install special by-pass line
back to tank so that air can pass
out of pump
Reservoir air vent plugged. Air must be allowed to circulate

in reservoir. Clean and/or replace
breather
Worn or broken parts Replace
Pump not delivering pressure Pump not delivering oil. See trouble section headed pump
not delivering oil.
Pressure adjusting screw not set Set adjusting screw to obtain
high enough. desired operating pressure.
Pressure being relieved through Inspect pump relief valves for dirt
relief valve. or electrical malfunction.
Oil bypassing to reservoir. Test circuit pressure
progressively. Watch for open-
center valves or other valves to
open reservoir.
Governor piston sticking. Inspect governor for dirt or
excessive scoring.
Defective pressure gauge. Install governor gauge known
to be accurate in a line open to
Gauge line is shut off. pump pressure.

Troubleshooting

Excessive wear� Abrasive matter in the hydraulic
oil being circulated through the
pump.
Oil viscosity too low at working Check Roadtec® oil
conditions. recommendations.
Sustained high pressure above Reduce pump pressure to
maximum pumps rating or higher minimum required for installation.
than system requirements.
Air recirculation causing chatter Align body and piping to remove
in system. strains.
Leakage at oil seal� Abrasives on pump shaft. Protect shaft from abrasive dust
or foreign material.
Pressure in pump case. Inspect case drain line for
restriction.

Troubleshooting

Troubleshooting
8.05 Troubleshoot Batteries

Battery not charging� Defective alternator. Replace alternator.
Alternator not turning. Check v-belt tension.
Defective regulator. Replace regulator.
Blown circuit breaker. Replace circuit breaker.

Troubleshooting

Troubleshooting
8.06 Troubleshoot Fluid Motors

Motor turning in wrong Incorrect piping between control Check circuit to determine correct
directions� valve and motor. piping.
Motor not turning over� System overload relief valve Check system pressure and reset
adjustment not set high enough. relief valve.
Relief valve sticking open. Remove dirt under pressure
adjustment ball or piston.
Free recirculation of oil to Directional control valve may be
reservoir being allowed through in open center neutral or other
system. return line unintentionally open.
Repair or replace valve.
Driven mechanism binding Remove motor and check torque

because of misalignment. requirement of driven shaft.
Pump not delivering pressure or Check pump delivery and
volume. pressure.
External oil leakage from Gaskets or O-ring leaking. Replace.
motor�
Motor turning in the wrong Valves sticking or binding. Check for dirt or gummy deposit.
direction� Check for contamination of oil.
Check for air in system. Check
for worn parts. Excessive wear
may be due to oil contamination.
Cylinder sticking or binding. Check for dirt, gummy deposits
or air leaks as above. Check
for misalignment, worn parts or
defective packing.
Internal leakage in cylinder. Repair or replace worn parts
and loose packing. Check oil
to see that viscosity is not
too low. Check for excessive
contamination or wear.
Air in system. Bleed air and check for leaks.
Check pump packing and line
connections on intake side
by pouring hydraulic oil over
suspected leak. As noise stops,
the leak has been located.
Tighten joints or change packing
or gaskets where necessary.

Troubleshooting

Troubleshooting
8.07 Troubleshoot Electrical Systems

Indicator lights do not Defective fuse. Replace machine fuse.
operate; control unit will not
drive unit�
Defective control cable. Replace control cable.
Defective control module. Replace control module.
Indicator lights operate; Control cable may be damaged or Replace cable.

control unit will not drive disabled.
valve�
Moisture in cable connectors. Dry out with heat or air.
Defective control module. Replace module.
Defective valve or solenoid. Manually actuate valve.
Indicator lights do not Indicator lamps burned out. Replace lamps.

operate; control unit will drive
hydraulics� Defective control module. Replace control module.
Both indicator lights operate; Defective hydraulic valve. Check hydraulics by operating
valves operate one way only� valve manually; if “OK”, then
check out resistance of valve coils
or solenoid (about 8 ohms at 12
volts, about 30 ohms for servo
valves.) Also check the machine
wiring.
Defective control module. Repair and replace as require.

Replace control module.
Valve operates one way only� Defective control module. Replace control module.
One indicator light working
(and is the appropriate light Defective sensor. Replace sensor.
for direction of travel)�
Valve operates, but only one Defective indicator lamp. Replace lamp.
indicator light functions�
Valve operates properly, but Defective control module. Replace control module.
both indicator lights remain
on�

Troubleshooting

Zero or null of control has Slope control mounting bolts not Tighten bolts.
shifted with respect to screed tight.
position�
Defective control module. Replace control module.
Defective sensor. Replace sensor.
Moisture build-up inside control Remove control module (panel)

housing on electrical connections. and dry out with heat or air.
Only one indicator light on Hydraulic valve drifting. Readjust valve null.
when valves are at null (ram
not moving)� Control module defective. Readjust control module.

Schematics
9.0 Schematics

Schematics

Schematics
9.01 Lubrication Chart

Schematics

Schematics
9.02 Hydraulic Schematics

Schematics

Schematics
9.03 Electrical Schematics

Schematics

STANDARD WARRANTY
STANDARD WARRANTY
(“Products”) to be free from defects in workmanship and material, commencing with the date of initial startup
This limited
warranty remains in force for the above time period only if all Manufacturer’s operational and
warranty procedures are followed and recommended maintenance is performed� Manufacturer’s liability
than thirty days after the discovery of such alleged defect.
If, within such warranty period, any Product shall be proven to Manufacturer’s satisfaction to be defective, it
shall be repaired or replaced, at Manufacturer’s option. All defective parts or components must be returned to
end-user’s sole and exclusive remedy for breach of this limited warranty. Manufacturer may, at its sole discretion,
refund the purchase price of the defective Product in lieu of repairing or replacing it, provided the defective
authorized by Manufacturer. Labor for warranty repair will be paid under a formula determined by Manufacturer.
Wear parts including, but not limited to, conveyor lines, screed plates, cutter teeth, tooth holders, scraper blades,
track pads, tires and conveyor belts are warranted only if found to be defective at time of shipment, but are not
warranted for the warranty period against wear or abuse.
No warranty shall apply to Products which have been repaired or altered by others so as, in Manufacturer’s
judgment, to adversely affect the same or which shall have been subject to negligence, accident, abuse or
improper care, installation, maintenance, storage or other than normal use or service, during or after shipment.
No warranty shall apply to any used Product. No warranty shall apply to any Product adversely affected by being
used with any machinery, part or accessory not manufactured or authorized by Manufacturer. With respect
to machinery, parts or accessories which are furnished but not manufactured by Manufacturer, the warranty
does not provide any warranty as to such items.
Manufacturer does not warrant or represent that any Product furnished by it meets any federal, state or local
safety, environmental or electrical regulations. Manufacturer is wholly discharged from all liability under this
warranty in the event that the purchaser of the Product fails to pay for it in accordance with the applicable
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED

(EXCEPT WARRANTY OF TITLE), INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY
FROM COURSE OF DEALING OR USAGE OF TRADE, EACH OF WHICH IS EXPRESSLY DISCLAIMED�
MANUFACTURER SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES WHATSOEVER
WITH RESPECT TO MACHINERY, PARTS OR ACCESSORIES MANUFACTURED OR FURNISHED BY IT OR
ANY SERVICES, UNDERTAKINGS, ACTS OR OMISSIONS RELATING THERETO� IN NO EVENT SHALL
MANUFACTURER BE LIABLE TO ANY PARTY FOR ANY LOSS OF USE, REVENUE OR PROFIT, OR FOR ANY
CONSEQUENTIAL, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR PUNITIVE DAMAGES WHETHER
ARISING OUT OF BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE� THERE
ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF�
ROADTEC, INC�
Chattanooga, Tennessee

STANDARD WARRANTY

Order Parts
Order Parts
Company name
Purchase order number
Personnel name and address
Method of shipment
Machine model and serial number
Part number, description and quantity of parts
Location of part(s) in Roadtec Parts Manual
ROADTEC Parts
Phone 1-423-265-0600
Toll Free 1-800-272-7100
Fax 1-423-267-8686
Receipt of Parts
Responsibility for breakage, loss or damaged goods ceases upon delivery of the merchandise to the
transportation company for which a receipt is received showing that the shipment was accepted by them
in good condition.
If material listed on the bill of lading or express receipt is short, broken or damaged, DO NOT accept the
shipment until the carrier’s agent makes a notation of the shortage or damage on the expense bill. Notify
the transportation company’s agent at once and request an inspection.
IMPORTANT!
support your claim�

Order Parts

INDEX
INDEX
Symbols E
50 Hours Maintenance 179 Electrical 11
100 Hours Maintenance 191 Electrical System 37
250 Hours Maintenance 195 electric systems 57
1000 Hours Maintenance 205 Emergency Stop Button 54
2000 Hours Maintenance 215 EMERGENCY STOP BUTTONS 43
engine 31
A Engine Air Intake Filter 181, 197
Engine Coolant 165
Air cleaner 31 Engine Diagnostic Gauge 77, 78, 79, 80, 81, 82, 87, 88, 89,
alternator 37 90, 91, 92, 93, 94, 95, 96, 97, 98, 99, 100, 101, 105,
ALTERNATOR 37 106, 107, 108, 109, 110, 111, 112, 113, 114, 115, 116,
Angle of Attack Threads 186 118, 119, 120
Auger 26, 35, 39, 71, 132, 134, 145, 176, 204, 213, 223, 225, engine fault codes 31
249, 251 Engine Oil 165, 193, 198, 263
Auger Drive Chain 223 extensions 39, 67, 71, 124, 127, 129, 134
Auger Extensions 39, 145
Auger Hanger 176, 225 F
Automatic Grade Control 39
Automatic Slope Control 39 31
Auxiliary Pump 239, 241 FIRE EXTINGUISHER 44
auxiliary pumps 31 Flow Gates 35, 133, 134
Averaging Ski 40 66
Fluid Capacities
B Fuel 31, 165, 169, 200
Hydraulic Tank 165, 177, 209, 210
batteries 37, 56, 57 FLUID REQUIREMENTS 165, 167
BATTERY 37 Forced Regen 103
Battery Disconnect Switches 43 Frame Lift Cylinders 236
Battery Electrolyte 183 Frame Raise 76, 152
Beacon Light 43 Front Wheel Assist 40
BEACON LIGHTS 43 fuel
Bogie Wheel Bearings 214 cap 51
Brake Release 230 FUEL 169
Fuel Filter 200
C Fuel pump 31
CAN-bus 37 Fuel Tank 165
Chain Case Bearings 176 Fume Extraction System 36, 43
conveyor 56, 66, 124, 133, 135
Conveyor Drive Chain 226 G
Conveyor Idler 174 Gearbox Oil 203, 212
Conveyor Pumps 239, 243, 244 Gear Oil 165
Conveyor System 36 Grease Points 165
Crown Control 190 Ground Control Boxes 70, 74
Cut-off shoes 67
Cut-Off Shoes 40 H
cylinders 31
HAZARD ALERT SIGNS 44
D Hazard Decals 59
head of material 43, 66, 71, 122, 127, 130, 131, 132, 133,
Daily Maintenance 167 134, 136, 139
DEF 165 Headshaft Bearings 174
DEF Tank 165 Hood Raise 230
Diesel Emissions Fluid Filters 217 Hopper 25, 35, 40, 71, 135, 258
Diesel Exhaust Fluid 165 hopper insert 40
DIMENSIONS 27 Hopper Insert 40
Dip Faults 139 HORN 44
Drive-Off Procedure 151 hoses 51
Drive System 33 Hydraulic 165, 295

INDEX
hydraulic oil 58, 60, 177 R

Hydraulic Strike-off Extensions 39
Radiator 56
L Radiator Fan Motor 252
169
Leg Tube Service Bar 43 Reverse Alarm 44
Lifting Points 221 Right 69
line of pull 66, 122 Right Hand Operator Console 70
Longitudinal Joints 139 Roadtec 11
LUBRICATION 161, 293 RP-250e 19, 65, 163
Lubrication Chart 165, 293
LUBRICATION CHART 293 S
M Safety 19, 41, 43, 48, 49, 53, 54, 58, 59, 164
Schematics 291, 295, 297
Machine Danger Zones 45 SCHEMATICS 291, 297
Machine Dimensions 27 Screed 25, 36, 39, 71, 72, 127, 128, 129, 131, 184, 187, 239,
MAINTENANCE 161, 163, 259, 261, 262, 263, 264, 265 257
Manual 19 Screed Extensions 39, 131
Material Feed System 35 Screed Generator Pump 239
Material Safety Data Sheet (MSDS) 54, 58 Screed Lift 72
Mat thickness 66, 137 Screed Set Up 129
Motors 249 Serial number 11
Service Department 11
N Set Flow Gates 133, 134
Shipping Height 27
negative crown 67
Shipping Width 27
Nomenclature 25
Smoothness 137, 149
Null 129, 131
Strainer 209
Null Screed 131
strike-off plate 67
stroke 31
O Synthetic Gear Oil 80W-140 165
Operate 124
operation 19 T
Operation 19, 53, 63, 65
Throttle 75, 154, 157, 159
Operator Station 25, 26
Tie Down Points 222
optional equipment 39, 40
Tire Pressure 189
Order Parts 301
tow points 36, 66, 129
OSHA 49
Tow Points 36
Transverse Joints 139, 140
P Travel Joystick 75, 103, 158
Parking Brake 103, 153 Troubleshooting 267
Paving Techniques 136, 137 Truck Hitch 40, 72
personal protective equipment 48 Turbo charger 31
Personal Protective Equipment 48
Personal Protective Equipment (PPE) 48 V
pivot points 66
VALVES 253
positive crown 67
Vibrators 67
Pre-Start Check List 124
voltage 57
Propel Pump Bypass 232
propel pumps 31
Propel Pumps 242
W
Proposition 65 Warning 15 Wheel Planetary Oil 202, 211
Pump Drive 165, 203, 212, 239
Push Rollers 35 Y
Yield Factor 138

NOTES
NOTES

NOTES

NOTES

NOTES

NOTES

NOTES

NOTES

NOTES

Post Office Box 180515
1-800-272-7100
www.roadtec.com
Agosto 20 de 2022
Bogotá D.C.
De: MAQUINARIA Y EQUIPOS CONCRESCOL

Director de Maquinaria y Equipos
Para: CONSORCIO ALIANZA VIAL SITP
Asunto: CERTIFICACION DE IDONEIDAD OPERADOR
El señor MORALES VARGAS HELIODORO identificado con número de cedula 13706601

labora con CONCRESCOL desde el 03 de julio del 2022 desempeñado el cargo de
OPERADOR DE TERMINADORA DE ASFALTO, demostrando sus capacidades de operación
y manejo seguro de los equipos y maquinas asignadas.
Reconozco en el la experiencia, el conocimiento y las capacidades de ejecutar todo tipo de

trabajos con las máquinas y equipos, ejecutando trabajos de calidad.
Quedo atento
Oswaldo Leon Oscar Alberto Torres Serrano

Director de Maquinaria y Equipo Representante Legal
Concrescol S.A Concrescol S.A
Nit. 830 071 114-6
Bogotá D.C. 23 de Agosto 2022
Señores
CONSORCIO ALIANZA VIAL SITP
ASUNTO: Certificación de Buen Estado de: Equipos: Concrescol SAS
Mediante la Presente la Empresa CONCRESCOL SA. Certifica Que los Equipos & Maquinaria
Presentados en la plantilla anexa; Se encuentran en Perfecto estado de Operatividad a nivel estructural
y mecánico; además cuentan con un Plan de Mantenimiento que se Cumple a Cabalidad garantizando
su Operatividad; Certifica de igual manera, que los mantenimientos se encuentran al día, Y Asume la
responsabilidad de ejecutar los mantenimientos Preventivos y Correctivos, de acuerdo al Plan de
Mantenimiento establecido por la Compañía, en las frecuencias descritas.
Descripción de Equipo Actividad Frecuencia SERIAL

781TA Terminadora de asfalto ROADTEC RP180-10 Mtt. Preventivo C/300 HR 276
702CD Compactador Doble rodillo CATERPILLAR CB534 C Mtt. Preventivo C/300 HR 5HH0452
Cordialmente,
JUAN GUILLERMO BENITEZ V

TP CN230-41893
CONCRESCOL S.A.S
Dirección de Correspondencia: Avenida Boyacá # 80-10 sur

Nit. 830 071 114-6
Bogotá D.C. 23 de Agosto 2022
Señores
CONSORCIO ALIANZA VIAL SITP
ASUNTO: Compromiso de Mantenimiento de Maquinaria & Equipos: Concrescol SA
Mediante la Presente la Empresa CONCRESCOL SA. Certifica Que los Equipos & Maquinaria
Presentados en la plantilla anexa; Cuentan con un Plan de Mantenimiento que se Cumple a Cabalidad
garantizando su Operatividad; Certifica de igual manera, que los mantenimientos se encuentran al día,
Y Asume la responsabilidad de ejecutar los mantenimientos Preventivos y Correctivos, de acuerdo al
Plan de Mantenimiento establecido por la Compañía, en las frecuencias descritas.
Descripción de Equipo Actividad Frecuencia SERIAL

781TA Terminadora de asfalto ROADTEC RP180-10 Mtt. Preventivo C/300 HR 276
702CD Compactador Doble rodillo CATERPILLAR CB534 C Mtt. Preventivo C/300 HR 5HH0452
Cordialmente,
JUAN GUILLERMO BENITEZ V

TP CN230-41893
CONCRESCOL S.A.S
Dirección de Correspondencia: Avenida Boyacá # 80-10 sur

F. Creación 01/02/2021
HOJA DE VIDA F. Revisión
N°
CARACTERISTICAS GENERALES
NOMBRE Pavimentadora de Asfalto MODELO RP180-10
CÓDIGO 781TA AÑO 2000
MARCA Roadtec SERIAL 276
Es una potente pavimentadora con neumaticos de caucho y está hecha

para el trabajo en autopistas. Los asientos de las estaciones para dos
operadores pueden moverse más allá de los laterales de la máquina a
fin de que el operador tenga una excelente vista hacia abajo de los
laterales de la máquina. Los asientos del operador de cuatro vías
hidráulicamente ajustables tienen un sistema de control del
movimiento para máxima comodidad. Los niveles de ruido de las
pavimentadoras Roadtec estan entre los mas bajos de la industria
gracias a los ventiladores con velocidad variable.
CARACTERISTICAS TECNICAS
PESO DE EMBARQUE 16420 Kg PESO DE OPERACIÓN SIN CARGA 16600 Kg
DIMENSIONES DE LA MAQUINA
LONGITUD TOTAL 6400 mm ALTURA INCLUYENDO ROPS 3680 mm
ANCHO TOTAL DELANTERO 3250 mm
CARACTERISTICAS
PROPULSIÓN
TIPO DE SISTEMA Hidrostatico
VELOCIDAD DE DESPLAZAMIENTO
VELOCIDAD EN ALTO 12,9 Km/h VELOCIDAD EN BAJO 20,5 Km/h
MOTOR
MARCA Y MODELO JHON DEEERE SISTEMA ELECTRICO 24 Voltios
POTENCIA NOMINAL @2600 Rpm 172 Hp
FRENOS
DE SERVICIO Hidraulicos DE EMERGENCIA/PARQUEO/SECUNDARIO Hidraulico con Motor
DIRECCION
DISEÑO Hidraulica TIPO DE SERVICIO Lleno Hidraulico
CAPACIDAD DE LLENADO
CAPACIDAD DEL TANQUE DE COMBUSTIBLE 100 Galones CAPACIDAD DEL CARÁCTER DEL MOTOR 6 Galones
CAPACIDAD DEL TANQUE HIDRAULICO 55 Galones CAPACIDAD DEL TANQUE DEL SISTEMA DE
SISTEMA DE ENFRENTAMIENTO DEL MOTOR 10 Galones RIEGO
FILTRACIÓN
FILTRO REFERENCIA CANTIDAD
Aire Primario DA2138 1
Aire Secundario DA4120 1
Aceite Motor P551352 1
Aceite Hidraulico BF7674D 1
Aceite Hidraulico BT287-10 1
Combustible P550251 1
LUBRICACIÓN
LUBRICANTE REFERENCIA CANTIDAD
Aceite Motor 15W40 6 Galones
Aceite Hidraulico SH-68 55 Gal

Movil 67 Terminadora de Asfalto

Uploaded by

Copyright:

Available Formats

Movil 67 Terminadora de Asfalto

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Movil 67 Terminadora de Asfalto

Uploaded by

Copyright:

Available Formats

RP-180

PN 262899 © ROADTEC INC. October 2005

First Release October 2005

Part Number 262899

Copyright Copyright © 2005

Publisher Roadtec, Inc.

4 Paver Operation & Service Manual

Paver Operation & Service Manual 7

2.17 Work Safely At Night ................................................................................55

8 Paver Operation & Service Manual

3.14 Pre-Start Conditions .............................................................................. 101

Paver Operation & Service Manual 9

4.04.06 Lubricate Angle of Attack Threads ..................................................... 164

10 Paver Operation & Service Manual

4.09.08 Engage / Disengage Propel Pump Bypass ........................................... 212

Paver Operation & Service Manual 11

7.03 Troubleshoot Operations ......................................................................... 261

12 Paver Operation & Service Manual

RP-180 Rubber Tire Asphalt Paver

DELIVERY DATE ______________

Paver Operation & Service Manual 13

14 Paver Operation & Service Manual

than thirty days after the discovery of such alleged defect.

does not provide any warranty as to such items.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED

Paver Operation & Service Manual 15

16 Paver Operation & Service Manual

WARNING: Breathing diesel engine exhaust exposes you to

• Always start and operate the engine in a well-ventilated area.

For more information, go to www.P65warnings.ca.gov/diesel.

ADVERTENCIA: Respirar los gases del escape de motores a

• Siempre encienda y opere el motor en un área bien ventilada.

Para mayor información visite www.P65warnings.ca.gov/diesel.

Paver Operation & Service Manual 17

18 Paver Operation & Service Manual

Paver Operation & Service Manual 19

20 Paver Operation & Service Manual

Paver Operation & Service Manual 21

22 Paver Operation & Service Manual

Paver Operation & Service Manual 23

24 Paver Operation & Service Manual

2.03 Inspect a New Machine

Paver Operation & Service Manual 25

26 Paver Operation & Service Manual

2.04 Unit Nomenclature

Tow Point Drive Wheel

Left Hopper Left Operator

Paver Operation & Service Manual 27

Left Operator Right Operator

28 Paver Operation & Service Manual

2.05 Machine Dimensions

7 ft. 7 in. (285 cm)

16 ft. 3 in. (535 cm)

Dimension English Metric

Shipping Height 11 ft. 5 in. 348 cm

Wheel Base 7 ft. 7 in. 285 cm

Shipping Width 8 ft. 2 in. 250 cm

Operating Width 10 ft. 6 in. 320 cm

Ground Clearance 6 in. 15.24 cm

Tractor Weight 29,280 lbs. 13, 344 kg