FT5336

Download as pdf or txt
Download as pdf or txt
You are on page 1of 13

FT5336GQQ

True Multi-Touch
Capacitive Touch Panel Controller

INTRODUCTION
The FT5336GQQ is single-chip capacitive touch panel controller ICs with a built-in enhanced Micro-controller unit (MCU).It adopts
the mutual capacitance and full screen common mode scan technology. Being coupled with a mutual capacitive touch panel, the
FT5336GQQ implements the user-friendly inputting function and be widely used in various portable devices, such as smart phones,
tablets, MIDs and GPS .

FEATURES
 2.8V to 3.3V Operating Voltage
 Mutual Capacitive Sensing Techniques
 IOVCC Supports from 1.8V or VDD3
 Full Screen Common Mode Scan Techniques
 Capable of Driving Single Channel (transmit/receive) Re-
 Supports up to 13 TX Lines + 24 RX Lines
sistance: Up to 30K Ω
 Supports up to 6.1" Touch Screen
 Capable of Supporting Single Channel (transmit/receive)
 High Report Rate: Up to 120Hz Capacitance: 60 pF
 Fully Programmable Scan Sequences to Support Various  Optimal Sensing Mutual Capacitor: 1pF~3pF
TX/RX Configurations
 12-Bit ADC Accuracy
 Proximity modes detection:
 Built-in Enhanced MCU
 Air Swipe
 Built-in LDO for Digital Circuits
 Glove Usage
 Cheek check  3 Operating Modes
 Immune to RF Interferences  Active
 True Multi-touch with up to 5 Points  Monitor
 Hibernate
 Touch Resolution of 100 Dots per Inch (dpi) or above --
 Operating Temperature Range: -40°C to +85°C
depending on the Panel Size
 Auto-calibration
 Support Interfaces :I2C

FocalTech Systems Co., Ltd · www.focaltech-systems.com · support@focaltech-systems.com


Document Number: D-FT5336-1301-V0.6 (Version: 0.6) Revised July. 18, 2013

F-OI-RD01-03-03-B
\\
TABLE OF CONTENTS
INTRODUCTION ............................................................................................................................................................I

FEATURES .......................................................................................................................................................................I

1 OVERVIEW ................................................................................................................................................................ 3
1.1 TYPICAL APPLICATIONS ......................................................................................................................................... 3
2 FUNCTIONAL DESCRIPTION ................................................................................................................................... 3
2.1 ARCHITECTURAL OVERVIEW .................................................................................................................................. 3
2.2 MCU .................................................................................................................................................................. 4
2.3 OPERATION MODES .............................................................................................................................................. 4
2.4 HOST INTERFACE .................................................................................................................................................. 4
2.5 SERIAL INTERFACE ............................................................................................................................................... 5
2.6 PROXIMITY MODES ............................................................................................................................................... 6
3 ELECTRICAL SPECIFICATIONS....................................................................................................................................... 7
3.1 ABSOLUTE MAXIMUM RATINGS .................................................................................................................................... 7
3.2 DC CHARACTERISTICS............................................................................................................................................... 7
3.3 AC CHARACTERISTICS ............................................................................................................................................... 7
3.4 I/O PORTS CIRCUITS ................................................................................................................................................ 8
3.5 POWER ON/RESET SEQUENCE .................................................................................................................................. 9
4 PIN CONFIGURATIONS ............................................................................................................................................... 10

5 PACKAGE INFORMATION ............................................................................................................................................ 12


5.1 PACKAGE INFORMATION OF QFN-5X5-48L PACKAGE ...................................................................................................... 12
5.2 ORDER INFORMATION.............................................................................................................................................. 13

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 2 of 13
1 OVERVIEW
1.1 Typical Applications

FT5336GQQ accommodates a wide range of applications with a set of buttons up to a 2D touch sensing device; their typical ap-
plications are listed below.
 Mobile phones
 Tablets
 MIDs
 Navigation systems, GPS
 Game consoles
 POS (Point of Sales) devices
 Portable MP3 and MP4 media players
 Digital cameras
FT5336GQQ support ≤6.1” Touch Panel, the spec is listed in the following table,
Panel Package
Model Name Touch Panel Size Typical Pitch
TX RX Type Pin Size
FT5336GQQ 13 24 QFN5*5 48 0.6-P0.35 ≤6.1" ~5mm

Remarks: FocalTech suggests using pitch between 4.0mm to 6.0mm; The customer can decide the pitch based on applications.

2 FUNCTIONAL DESCRIPTION
2.1 Architectural Overview
Figure2-1 shows the overall architecture for the FT5336GQQ.

AFE INTERFACE

TX
12bit Port0
LPF SAR PORT
I2C
ADC Controller
RX Port1

High speed Digital processor

Flash Enhanced MCU) Data ram

CGU OCps DSP ASM

EAC
48MHz low power
POR Power Regulator
internal Oscillator

Figure 2-1 FT5336GQQ System Architecture Diagram

The FT5336GQQ is comprised of five main functional parts listed below,

 Touch Panel Interface Circuits


The main function for the AFE and AFE controller is to interface with the touch panel. It scans the panel by sending AC signals to the
panel and processes the received signals from the panel. It includes both Transmit (TX) and Receive (RX) functions. Key parameters
to configure this circuit can be sent via serial interfaces.
 Enhanced MCU with DSP accelerator

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 3 of 13
For the Enhanced MCU, larger program and data memories are supported. Furthermore, a Flash memory is implemented to store
programs and some key parameters.
Complex signal processing algorithms are implemented by MCU and DSP accelerator to detect the touches reliably and efficiently.
Communication protocol software is also implemented in this MCU to exchange data and control information with the host pro-
cessor.
 External Interface
 I2C: an interface for data exchange with host
 INT: an interrupt signal to inform the host processor that touch data is ready for read
 RSTN: an external low signal reset the chip. The port is also use to wake up the FT5336GQQ from the Hibernate mode.
 A watch dog timer is implemented to ensure the robustness of the chip.
 A voltage regulator to generate 1.8V for digital circuits from the input VDD3 supply
 Power On Reset (POR) is active until VDDD is higher than some level and hold decades of μs.

2.2 MCU
This section describes some critical features and operations supported by the enhanced MCU.
Figure 2-2 shows the overall structure of the MCU block. In addition to the enhanced MCU core, we have added the following
circuits,
 A DSP accelerator cooperates with MCU to process the complex algorithms
 Timer: A number of timers are available to generate different clocks
 Clock Manager: To control various clocks under different operation conditions of the system

Program Data
Memory Memory

Clock Enhanced
Manager MCU Core

Master Watch
Timer
Clock dog
Figure 2-2 MCU Block Diagram
2.3 Operation Modes
FT5336GQQ operates in the following three modes:
 Active Mode
When in this mode, FT5336GQQ actively scans the panel. The default scan rate is 100 frames per second. The host processor can
configure FT5336GQQ to speed up or to slow down.
 Monitor Mode
In this mode, FT5336GQQ scans the panel at a reduced speed. The default scan rate is 25 frames per second and the host processor
can increase or decrease this rate. In this mode, most algorithms are stopped. A simpler algorithm is being executed to determine if
there is a touch or not. When a touch is detected, FT5336GQQ shall enter the Active mode immediately to acquire the touch in-
formation quickly. During this mode, the serial port is closed and no data shall be transferred with the host processor.
 Hibernate Mode
In this mode, the chip is set in a power down mode. It shall only respond to the “RESET” signal from the host processor. The chip
therefore consumes very little current, which help prolong the standby time for the portable devices.
2.4 Host Interface
Figure 2-3 shows the interface between a host processor and FT5336GQQ. This interface consists of the following three sets of
signals:

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 4 of 13
 Serial Interface
 Interrupt from FT5336GQQ to the Host
 Reset Signal from the Host to FT5336GQQ

TP Module

Serial
Interface
TX
TP FT5336GQQ Host
RX
/INT
/RST

Figure 2-3 Host Interface Diagram


The serial interface of FT5336GQQ is I2C. The detail of the interface is described in detail in Section 2.5. The interrupt signal (/INT)
is used for FT5336GQQ to inform the host that data are ready for the host to receive. The /RST signal is used for the host to wake up
FT5336GQQ from the Hibernate mode. After resetting, FT5336GQQ shall enter the Active mode.

2.5 Serial Interface


FT5336GQQ supports the I2C interfaces, which can be used by a host processor or other devices.

The I2C is always configured in the Slave mode. The data transfer format is shown in Figure 2-4.

SDA
MSB ACK from ACK from
slave receiver
SCL
1 2 3~6 7 8 9 1 2 3~7 8 9
START or ACK
ACK
repeat START Stop

Figure 2-4 I2C Serial Data Transfer Format

SLV addr Data[n] Data[n+1] Data[n+2]

S A[6:0] W A D[7:0] A D[7:0] A D[7:0] A P

Figure 2-5 I2C master write, slave read

SLV addr Data[n] Data[n+1] Data[n+2]

S A[6:0] R A D[7:0] A D[7:0] A D[7:0] N P

Figure 2-6 I2C master read, slave write

Table 2-1 lists the meanings of the mnemonics used in the above figures.

Table 2-1 Mnemonics Description

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 5 of 13
Mnemonics Description
S I2C Start or I2C Restart

A[6:0] Slave address

R/ W READ/WRITE bit, ‘1’ for read, ‘0’for write

A(N) ACK(NACK) bit


STOP: the indication of the end of a packet (if this bit is missing, S will indicate the end
P
of the current packet and the beginning of the next packet)

I2C Interface Timing Characteristics is shown in Table 2-2.

Table 2-2 I2C Timing Characteristics

Parameter Min Max Unit


SCL frequency 10 400 KHz
Bus free time between a STOP and START condition 4.7 \ us
Hold time (repeated) START condition 4.0 \ us
Data setup time 250 \ ns
Setup time for a repeated START condition 4.7 \ us
Setup Time for STOP condition 4.0 \ us

2.6 Proximity Modes


FT5336GQQ support the following three proximity modes:
 Air Swipe
In this mode, FT5336GQQ could recognize the large object movement in two dimensions (x and Y axis). This can enable functions
like picture scrolling, page up and page down.
 Glove Usage
FT5336GQQ has increased sensitivity that allows the touch sensors to detect Finger through glove.
 Cheek Check
As soon as user’s cheek approaches to mobile phone screen, cheek proximity detection allows the host to turn off the mobile phone
screen.

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 6 of 13
3 ELECTRICAL SPECIFICATIONS
3.1 Absolute Maximum Ratings
Table 3-1 Absolute Maximum Ratings

Item Symbol Value Unit Note


Power Supply Voltage 1 VDDA - VSSA -0.3 ~ +3.6 V 1, 2
Power Supply Voltage 2 VDD3 – VSS -0.3 ~ +3.6 V 1, 3
I/O Digital Voltage IOVCC 1.8~3.6 V 1
Operating Temperature Topr -40 ~ +85 ℃ 1
Storage Temperature Tstg -55 ~ +150 ℃ 1

Notes

1. If used beyond the absolute maximum ratings, FT5336GQQ may be permanently damaged. It is strongly recommended that the
device be used within the electrical characteristics in normal operations. If exposed to the condition not within the electrical char-
acteristics, it may affect the reliability of the device.
2. Make sure VDDA (high) ≥VSSA (low)
3. Make sure VDD (high) ≥VSS (low)

3.2 DC Characteristics

Table 3-2 DC Characteristics (VDDA=VDD3=2.8~3.6V, Ta=-20~70°C)

Item Symbol Unit Test Condition Min. Typ. Max. Note


Input high-level voltage VIH V 0.7 x IOVCC -- IOVCC

Input low -level voltage VIL V -0.3 -- 0.3 x IOVCC

Output high -level voltage VOH V IOH=-0.1mA 0.7 x IOVCC -- --

Output low -level voltage VOL V IOH=0.1mA -- -- 0.3 x IOVCC

I/O leakage current ILI uA Vin=0~VDDA -1 -- 1


Current consumption VDDA=VDD3 = 2.8V
Iopr mA -- 7.00 --
(Normal operation mode) Ta=25℃ MCLK=24MHz
Current consumption VDDA=VDD3 = 2.8V 2.75
Imon mA -- --
(Monitor mode) Ta=25℃ MCLK=24MHz
Current consumption VDDA=VDD3 = 2.8V 20
Islp uA -- --
(Sleep mode) Ta=25℃ MCLK=24MHz

Step-up output voltage VDD5 V VDDA=VDD3= 2.8V 0.25

VDDA
Power Supply voltage V 2.8 -- 3.6
VDD3
Notes: This consumption data is intended for design guidance only. Actual current will depend on the particular sensor
design and firmware options.

3.3 AC Characteristics

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 7 of 13
Table 3-3 AC Characteristics of TX & RX
Item Symbol Test Condition Min Typ Max Unit Note
TX acceptable clock ftx -- 150 -- KHz

TX output rise time Ttxr -- 140 -- nS

TX output fall time Ttxf -- 140 -- nS

RX input voltage Trxi 1.2 -- 1.6 V

3.4 I/O Ports Circuits

VDDA IOVCC

VDDA

Input circuit

IOVCC

Floating Sub Output enable


Output data

Figure 3-1 General Purpose In/Out Port Circuit.


The input/output property can be configured via firmware setting. The firmware can also control its output behavior as push-pull or
as open-drain that SDA of I2C interface is required.

VDDA

3K
300

Figure 3-2 Reset Input Port Circuits

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 8 of 13
3.5 POWER ON/Reset Sequence

Reset should be pulled down to be low before powering on and powering down. I2C shouldn’t be used by other devices during Reset
time after VDD powering on (Trtp). INT signal will be sent to the host after initializing all parameters and then start to report points
to the host. If Power is down, the voltage of supply must be below 0.3V and Tpdt is more than 1ms.

Tris

Power

Figure 3-3 Power on time

Tpdt
Power

0.3V

Figure 3-4 Power Cycle requirement

Trtp
Tvdr
Tvdr
Tpon

VDD
Reset

INT

I2C

Figure 3-5 Power on Sequence


Reset time must be enough to guarantee reliable reset, the time of starting to report point after resetting approach to the time of
starting to report point after powering on.

Trsi

Trst

Power
RESET

INT

I2C

Figure 3-6 Reset Sequence

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 9 of 13
Table 3-5 Power on/Reset Sequence Parameters

Parameter Description Min Max Units


Tris Rise time from 0.1VDD to 0.9VDD -- 5 ms
Tpdt Time of the voltage of supply being below 0.3V 5 -- ms
Trtp Time of resetting to be low before powering on 100 -- μs

Tpon Time of starting to report point after powering on 200 -- ms


Tvdr Reset time after VDD powering on 1 -- ms
Trsi Time of starting to report point after resetting 200 -- ms
Trst Reset time 1 -- ms

4 PIN CONFIGURATIONS
Pin List of FT5336GQQ

Table 4-1 Pin Definition of FT5336GQQ

Name Pin No. Type Description

TX13 36 O Transmit output pin


TX12 35 O Transmit output pin
TX11 34 O Transmit output pin
TX10 33 O Transmit output pin
TX9 32 O Transmit output pin
TX8 31 O Transmit output pin
TX7 30 O Transmit output pin
TX6 29 O Transmit output pin
TX5 28 O Transmit output pin
TX4 27 O Transmit output pin
TX3 26 O Transmit output pin
TX2 25 O Transmit output pin
TX1 24 O Transmit output pin
internal generated 5V power supply, A 1μF ceramic
VDD5 23 PWR
capacitor to ground is required.
VDDA 22 PWR Analog power supply
VSSA 9 PWR Analog ground
VSS 37 PWR Analog ground
38 Digital power supply (1.8V), generated internal. A 1
VDDD PWR
μF ceramic capacitor to ground is required.
internal generated reference power supply, A 1μF
VREF 8 PWR
ceramic capacitor to ground is required.
RSTN 39 I External Reset, Low is active
SCL 43 I/O I2C clock input
SDA 42 I/O I2C data input and output
GPIO 41 I/O General Purpose Input/Output port
INT/ 40 Interrupt request to the host, or Wakeup request from
I/O
Wakeup the host.
RX1 44 I Receiver input pins

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 10 of 13
RX2 45 I Receiver input pins
RX3 46 I Receiver input pins
RX4 47 I Receiver input pins
RX5 48 I Receiver input pins
RX6 1 I Receiver input pins
RX7 2 I Receiver input pins
RX8 3 I Receiver input pins
RX9 4 I Receiver input pins
RX10 5 I Receiver input pins
RX11 6 I Receiver input pins
RX12 7 I Receiver input pins
RX13 10 I Receiver input pins
RX14 11 I Receiver input pins
RX15 12 I Receiver input pins
RX16 13 I Receiver input pins
RX17 14 I Receiver input pins
RX18 15 I Receiver input pins
RX19 16 I Receiver input pins
RX20 17 I Receiver input pins
RX21 18 I Receiver input pins
RX22 19 I Receiver input pins
RX23 20 I Receiver input pins
RX24 21 I Receiver input pins
VDDD
RSTN

TX13
GPIO

TX12
RX5

SDA
RX2
RX1

SCL
RX4
RX3

INT

VSS
48
47
46
45
44
43
42
41
40
39
38
37
36
35

RX6 1 34 TX11
RX7 2 33 TX10
RX8 3 32 TX9
RX9 4 31 TX8
RX10 5 30 TX7
RX11 6 FT5336GQQ 29 TX6
RX12 7 28 TX5
VREF 8 27 TX4
VSSA 9 26 TX3
RX13 10 25 TX2
13

14

16
17
18
19
20
21
22
23
24
11
12

15

VDDA
RX15

RX18
RX19

VDD5
RX16
RX17

RX20
RX21
RX22
RX23
RX24
RX14

TX1

FT5336GQQ Package Diagram

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 11 of 13
5 PACKAGE INFORMATION
5.1 Package Information of QFN-5x5-48L Package

Millimeter
Item Symbol
Min Type Max
Total Thickness A 0.5 0.55 0.6
Stand Off A1 0 0.035 0.05
Mold Thickness A2 ---- 0.4 0.425
L/F Thickness A3 0.152 REF
Lead Width b 0.13 0.18 0.23
D 5 BSC
Body Size
E 5 BSC
Lead Pitch e 0.35 BSC
J 3.6 3.7 3.8
EP Size
K 3.6 3.7 3.8
Lead Length L 0.35 0.4 0.45
Package Edge Tolerance aaa 0.1
Mold Flatness bbb 0.1
Co Planarity ccc 0.08
Lead Offset ddd 0.1
Exposed Pad Offset eee 0.1

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 12 of 13
5.2 Order Information

QFN
Package Type 48Pin(5 * 5 )
0.6 - P0.35
Product Name FT5336

Note:
1). The last three letters in the product name indicate the package type , lead pitch and thickness and numbers of TX and RX.

2). The third last letter indicates the package type .


G : QFN-5*5
3). The second last letter indicates the lead pitch and thickness.
M : 0.6 - P0.35
4). The last letter indicates the numbers of TX and RX.
J: 11TX-16RX

T: Track Code
F/R:”F” for Lead Free process, F T 5336GQQ
TFYWWSV
”R” for Halogen Free process
Y: Year Code
WW: Week Code
S: Lot Code
V:IC Version

Product Name Package Type # TX Pins # RX Pins

FT5336GQQ QFN-48L 13 24

END OF DATASHEET

HIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO FOCALTECH SYSTEMS CO.,LTD., AND MAY NOT BE
REPRODUCED, DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF
FOCALTECH SYSTEMS CO.,LTD.

Copyright © 2013, FocalTech Systems CO., Ltd . All rights reserved Version 0.6︱Page 13 of 13

You might also like