At a Glance Getting Started

GPS Vehicle Tracker 1.1 Overview 2.1 Installing the SIM card
Important 1 A SIM card is required in order to use cellular services
when connecting to GSM networks.
1.2 Accessories
User Guide Power cabte/Relay 2 Keep ihe SIM card GPRS availabiity
3 Note dawn the SIM card phone numbers which is device
(Version V2.1)
1.3 Wiring Diagram contacftig numbers. Open the side plug, irutall the SIM card In
the right direction, tvm on the device.

2.2 Setting up and activating the device

To set up and activating ttie device, you should send SMS to device numbers
by mobile phone.
Setting server
SMS: SERVER, 1 fvt05s.pro1rack365.conxfia42<04

2.3 Installing the device

23.1 Connect according wires to your car by referring to Wiring Diatom In
Chapter 1.3

2.32 Install ttie device in following ttiree suggested place: Important 1 Make It
covert for security factors.
2Keep away from high power electrical devicesrsucti as reversing
radar,anfl-theft device or other vehicle communication equipment which may
affect ttie device signal.
3Keep the device front face up&No metallic cases above ttie
Pump
device which may affect signal as well Such as the windshield which
1$ pasted with metal friermal-pfotecttve coating or heating coating.
 Alarm management 6.2 When the GPS signal reception abnormal, please take it into ■fhe broad
Checking location place positioning, general first positioning need 1-2 minutes. If a long time does
not positioning, please check the device installation location if meets the
*When any kinds of alarms happened, device will send alarm SMS&CALL SOS requirements, the normal installaiion without metal shielding.
numbers.
6.3 When the GSM signal reception abnormal, please check the device SIM
5.1 Vibration Alarm card is installed correctly; or ihe location may not cover where signal coverage.
When ACC is off and some vibration happened, device will alarm.
GSM signal (such as a basement), please use in the place
3.1 Via SMS 5.2 Cut-off alarm
WHERE# When external power is cut, device will alarm. 6.4 When power-up ,the red power light is off, please check the wiring is
3.2 Via tracking platform 5.3 Geo-fence alarm correct, and after exclude ihe internal device problem then can power-up again.
www.proirack365.com After setting geo-fence range, if the device come in&out the range, it will alarm.
Ask your disiributor for log-in account and password.
5.4 Low-power alarm
When external power is cut, device will keep working with its backup battery and
when its battery is too low, device will alarm.
5.5 Movement alarm
Basic When ACC is off, if the vehicle is moved, device will alarm.
4.1 LED indication Trouble shooting Maintain Information
4.1.1 Red LED -Power status
Customer Name: Tel: Add: IMEI;
Slow flashing Normal working (backup battery) 6.1 When device in the background display not on-line or off-line., First Purchase Date:
Solid bright Normal working (external power supplying) observe the device 3 indicator is normal, according to the device lights staius to
Off Power off judge device work condiiion, if the red light flashes, the green light is not bright Maintain Records
please check that the SIM card is installed correciiy, if the installation is no Date Problem Description Records Debug Engineer
4.1.2 Green LED -GSM status problem, please replace-fhe SIM card test again. Under no condition to observe
Quick flashing GSM initialization the siiuation, use mobile phone dial SIM card device number, if not connect
Slow flashing Normal working with GSM neiwork successful, indicating ihat the device Area is no GSM signal or signal is weak,
Off No GSM signal please fry it again in a good signal place; if the device is insufficient balance or
out of service,Please iry again after recharge; if connect successful, please
consult ttie appropriate operator if SIM card is open GPRS function; if not
4.1.3 Blue LED -GPS status
connected,prompt power off ,please check ihat the device is installed properly.
Quick flashing Searching GPS signal
Slow flashing Normal working with GPS fixed
Off No GPS fixed
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any inte rference received,
including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interferenceto radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, this grant is
applicable to only mobile configurations. The antennas used for this
transmitter must be installed to provide a separation distance of at least 20cm
from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter.