Syncro Prop Tech Manual

ProMotoTools Dsync 2
by Prop-Tech engineering Installation and User Guide
Thank You
for purchasing our product.
Please read the following instructions carefully before operating this product.
ProMotoTools
is a unique computer aided motorcycle diagnostic tools family:
Laser Evo for motorcycle frame measurement and rear wheel alignment tool
Dsynch2 for motorcycle intake port adjustment and diagnostics
CR01, CR02 current reader for battery, starter motor, engine conditions examination
ExPro01 exhaust tester for checking melted catalytic converter and muffler diagnostics
PT01 Fuel tank and fuel pump tester
Dsynch2 Installation and User Guide 1

Prerequisites
Operating system
• Microsoft Windows 7 with Service Pack 2 or newer
• Microsoft Windows 10 recommended
Hardware requirements
• At last 80 megabytes of free disk space
• Minimum 4 gigabytes of RAM
• FullHD or higher screen resolution
• .NET 4 runtime environment
Internet connection
Periodic software refreshing for software components is required for perfect operation.
Software updates are required too, because only new versions handling well the refreshed
components. User will be informed when new software version is available.

Installation
Step 1
Please download the installer application from our server. Do not download the installer
from 3rd party sites. The installed application is regularly checks for software update.
Step 2
Run the installer by double clicking on the previously downloaded
syncpt_a.b.c.d.exe (where abcd represents the current software version)
Step 3
Latest Windows versions are protecting users against unknown software sources. But in
this case, it is not needed.
Click on “More info” link.
Click on “Run anyway” button.
Click on “Yes” button.

Step 4
When installer starts, please do the followings
This is the Welcome Screen of installer.

Click on “Next” button to continue.
On this screen You can select a different

destination folder for the application.
Leave it with default contents if You’re in a

hurry. (Recommended.)
Please check Your available free disk space,

then click on “Next” button.
If You wish, enable additional desktop icon.
Be sure to create a start menu folder!
Click on “Next” button.

Please be patient for a few seconds.
Done. Press “Finish” button.

Remove application from computer

The easiest way to uninstall the application is using our uninstaller tool from start menu
folder. Simply click on uninstaller. That’s all.
Using the application
Before You begin
We assume that You’re a trained professional and You have already connected the
instrument’s silicone rubber hoses to the motorcycle.
Run the application
Click the program’s icon in the start menu.

Main window
1. Main menu
A,B,C,D: turn on/off measuring cylinders
2. Start and stop measuring
E,F,G,H: select master cylinder
3. USB connection status
1. Red – no connection
2. Yellow –
▪ connection pending
▪ internet update required
3. Green – hardware connected, ready to measure
4. Snapshot “photo” buttons
◦ beginning of measurement – for “before” status
◦ end of measurement – for “after” status
5. Examine snapshots in a window
6. Set sensitivity
7. Playback button - replay measurement
8. Time track display
9. Mode switch: chart / RPM
10. Time sensitivity (horizontal stretch)

Your contact information

If You ever like to print a measurement, it is highly recommended to fill Your own
business info. This is an initial task. You can find this box under Main menu / Settings.
Fill these fields, and press exit icon when done.

Motorcycle and its owner’s data

For saving and printing results, you have to fill the followings.
When it’s done, click on the exit icon.

Measuring
Start the engine and please be patient to reach its optimal operating temperature.
Connect the hardware instrument into a free USB port on Your computer. Do not
connect any other measuring tool in same time. To start measuring, click on the “Start”
[2] button.
Don’t forget to take snapshot from the “before synchronization” operating state. When
synchronization finished, take one more snapshot with the result. Click on snapshot
camera icons [4]. You can check these snapshots with eye buttons [5]. Take a new
snapshot when needed.
Start Your synchronization task with setting throttle body valves or air adjusting screws.
Always follow bike specific service manual instructions. The computer calculates
average values for each cylinder. Examine diagrams of each cylinder, one by one. When
these columns are similar, the cylinders are in the same condition. In the accepted
region, the software changes the background color from white to green.

Diagnosis – Understanding curves

The cylinder and valve condition can be inferred from the following logic:
If the engine has a long intake port the
diagram will be flattened.
If a vacuum chamber connected to a

cylinder the diagram also will be
flattened.
In this case, You can examine an intake

port leak:
There is air induction in the intake port
(Rubber parts leaking, etc.)
• blue: normal state

• red: wrong state

This example demonstrates an exhaust

valve problem:
Small exhaust valve clearance, or leaking
valve seat

Intake valve fault:

Small intake valve clearance, or leaking
valve seat


RPM mode
Select RPM from mode dropdown menu to access RPM mode.
When you’re done with intake port balancing and you have a chance to adjust fuel/air
mixture by carb pilot crews of any tools with fuel injected models (different tuning
electronics, such as products from Dynojet, Yoshimura, etc.) with this screen you can see
RPM “UP” or ”DOWN” info.
It’s indicates your individual adjustment: good (UP rpm) or wrong (DOWN rpm)
It’s indicates mixture settings by cylinders. When direction of changes are right the RPM
is increasing and “UP” will shown, otherwise “DOWN” will displayed. This setting is
applicable for all individual cylinders.

Faults record samples:
Throttle bearing fault:

Pressure sudden increase (throtthe valve changed position)
Intake port leaking case:

Intake port leaking case:

#2, #3, #4 switch off
NOTE: AWG pressure 895 hKP, normally approx 700, poor engine condition

Idle speed mixture monitoring:
NOTE: #2 #3 cylinders OEM setting more fuel. You can see the effect at IN&EX valves
overlaping. More exhauset gases has more effect az intake port.
Prop-Tech Ltd.
2509 Esztergom-Kertváros
Motorsort u. 1
Hungary
prop-tech-tools.com

Syncro Prop Tech Manual

Uploaded by

Copyright:

Available Formats

Syncro Prop Tech Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Syncro Prop Tech Manual

Uploaded by

Copyright:

Available Formats

ProMotoTools Dsync 2

by Prop-Tech engineering Installation and User Guide

Dsynch2 for motorcycle intake port adjustment and diagnostics

PT01 Fuel tank and fuel pump tester

Dsynch2 Installation and User Guide 1

Dsynch2 Installation and User Guide 2

Click on “More info” link.

Click on “Run anyway” button.

Click on “Yes” button.

Dsynch2 Installation and User Guide 3

This is the Welcome Screen of installer.

On this screen You can select a different

Leave it with default contents if You’re in a

Please check Your available free disk space,

If You wish, enable additional desktop icon.

Be sure to create a start menu folder!

Click on “Next” button.

Dsynch2 Installation and User Guide 4

Please be patient for a few seconds.

Done. Press “Finish” button.

Dsynch2 Installation and User Guide 5

Remove application from computer

Using the application

Before You begin

Run the application

Click the program’s icon in the start menu.

Dsynch2 Installation and User Guide 6

Dsynch2 Installation and User Guide 7

Your contact information

Fill these fields, and press exit icon when done.

Dsynch2 Installation and User Guide 8

Motorcycle and its owner’s data

When it’s done, click on the exit icon.

Dsynch2 Installation and User Guide 9

Dsynch2 Installation and User Guide 10

Diagnosis – Understanding curves

If a vacuum chamber connected to a

In this case, You can examine an intake

• blue: normal state

Dsynch2 Installation and User Guide 11

This example demonstrates an exhaust

• blue: normal state

Intake valve fault:

• blue: normal state

Dsynch2 Installation and User Guide 12

Select RPM from mode dropdown menu to access RPM mode.

Dsynch2 Installation and User Guide 13

Faults record samples:

Throttle bearing fault:

Intake port leaking case:

Dsynch2 Installation and User Guide 14

Intake port leaking case:

Dsynch2 Installation and User Guide 15

Idle speed mixture monitoring:

Dsynch2 Installation and User Guide 16

You might also like