Universal Intelligent Controller

UIC-DX330 Series
Screw Air Compressor Controller

2005-Dec rev. 1
Firmware v2.7b R071116

Joongang-ilbo building 6F, Wonsi-dong, Danwon-gu

Ansan-si, Gyeonggi-do, KOREA
Tel : 031-495-3767 , 031-495-3916 (Customer Service Center)
Fax : 031-495-3917 Homepage : www.dotech21.com
E-mail : [email protected]

DOTECH, INC
UIC-DX330 Series User’s Manual Rev 2.0

※ Read this direction for safety first..

▣ Direction for safety
This direction is for using the product correctly so that you could be safe from danger or incident.
Please carefully keep this all direction.

z Please use with being attached to a dual safety device in case of using for controlling instruments which could be

effective to human life or property (eg: controlling atomic energy, medical instruments, cars, trains, flights, burners,

amusement instruments or safety machinery).

z Please use with panel, there is a possibility getting an electric shock.

z Do not inspect or test with connecting power.

z Please connect after checking the terminal number when connecting power.

z Do not reorganize except mechanic from 『Dotech』.

z Do not use outdoor. It would be a cause making the product life shorter.

z When connecting wires, please give a good screw on terminal. There is a possibility causing a fire with bad connection.

z Please use in the proper performance zone. If you don’t, there is a possibility making the product life shorter or, causing

a fire accident.

z Do not use a load which is exceeded proper value of opening and shutting capacity of a relay contact. This will cause

bad insulation, bad contact and bad connection.

z When cleaning, water or liquid including oil are prohibited, only clean with soft and dried cloth.

z Do not use in the place where there is inflammability gas, explosiveness gas, moisture, a direct ray of light, radiation,

vibration and a shock.

z Please prevent from getting a dirt or leftover wire inside of this product.

When connecting a sensor, please connect correctly after checking the polarity.

Some of the setting, size etc. on this manual could be changed without an advance notice.

-2-
UIC-DX330 Series User’s Manual Rev 2.0

. Warranty Information
This is the warranty below for customer who has a license or product from 『Dotech』.

condition of warranty
The warranty period for 『Dotech』 products is a year so that it is provided support of the product during the warranty
period.

『Dotech』 does not have a responsibility for problems of product under the circumstance below.
In the case of using without concerning the proper form mentioned on the manual.

In the case of problems caused from both external artificial and environmental factors.

Please contact 『Dotech』 in advance if there is any problem of product caused during the warranty period.

If the problem of product is informed from customer in the warranty period, it will be checked up in the customer area or sent to

『Dotech』 to check and conduct repair of exchange services directly. If the product is over the warranty period or that is on the
condition that it is not mentioned on manual, customer would be suggested to pay the cost of repair, exchange and delivery.

On the condition that suggestions for ‘Warranty Condition Performance’ below are not against the law, 『Dotech』 is not
responsible for any compensation and guarantee caused by losses or damages by business interruption, loss, return.

Warranty Condition Performance

Dotech is not responsible for any loss, damages, expenses insisted by customer, delegate, contractor except for customer claims

caused by the condition of warranty above.

The condition of warranty mentioned above is the exclusive customer’s right. Dotech refuses any conditions of warranty for

special purpose except for the condition of warranty.

Warranty Condition Performance does not apply any trouble caused by not following exact direction. It is responsibility for

customer to decide usage or product.

All the conditions of warranty are actually applied and Nobody has authority to modify or extend.

-3-
UIC-DX330 Series User’s Manual Rev 2.0

Revision Information

Nov. 17, 2007: Revision #1 (F/W Rev 2.7b R071116)

-4-
UIC-DX330 Series User’s Manual Rev 2.0

Index
1. OUTLINE ................................................................................................................................................................................. 8

1) SPECIAL ADVANTAGES ......................................................................................................................................... 9

1-1) Noise Solution ................................................................................................................................................................. 9
1-2) RISC TYPE MICOM ..................................................................................................................................................... 9
1-3) Black Box : A recorder of operation status ..................................................................................................................... 9
1-4) Display for operation status and/or maintenance information (trip computer).............................................................. 9
1-5) Big Size Graphic LCD (Wide Temperature Range Type : -20 ~ +70℃) ......................................................................... 9
1-6) Minimization ................................................................................................................................................................... 9
1-7) Scalability ....................................................................................................................................................................... 9
2) BASIC SPECIFICATION ........................................................................................................................................ 10
2-1) General Specification ................................................................................................................................................... 10
2-2) CPU & LCD ................................................................................................................................................................. 10
2-3) Digital Input & Output ................................................................................................................................................. 10
2-4) Analogue Input & Output.............................................................................................................................................. 10
2-5) Communication Specification ....................................................................................................................................... 10
2-6) Installation Circumstance ............................................................................................................................................. 10

2. INPUT / OUTPUT SPECIFICATION.................................................................................................................................. 11

1) DIGITAL INPUT SIGNAL ...................................................................................................................................... 11

2) DIGITAL OUTPUT SIGNAL ................................................................................................................................... 12
3) ANALOGUE INPUT SIGNAL .................................................................................................................................. 13
4) ANALOGUE OUTPUT SIGNAL .............................................................................................................................. 14
5) COMMUNICATION SIGNAL .................................................................................................................................. 15
5-1) SYSTEM BUS ................................................................................................................................................................ 15
5-2) LOCAL BUS.................................................................................................................................................................. 15
6) CONTROL POWER INPUT .................................................................................................................................... 16

3. CONSTITUTION ................................................................................................................................................................... 17

1) OPERATION AND DISPLAY PART .......................................................................................................................... 17

1-1) Basic Constitution ......................................................................................................................................................... 17
1-2) Operation Part .............................................................................................................................................................. 17
1-3) Program Setup Part ...................................................................................................................................................... 17
2) MEASUREMENTS AND MOUNT INFORMATION ...................................................................................................... 18
3) DISPLAY FOR OPERATION STATUS ....................................................................................................................... 19
4) OPERATION BUTTON FUNCTION ......................................................................................................................... 19
5) STATUS DISPLAY RAMP ...................................................................................................................................... 20
6) SYMBOL EXPLANATION ...................................................................................................................................... 21

-5-
UIC-DX330 Series User’s Manual Rev 2.0

6-1) Equipment Status Display ............................................................................................................................................. 21

6-2) Digital Input Signal ...................................................................................................................................................... 22
6-3) Digital Output Signal .................................................................................................................................................... 22

4. MENU CONSTITUTION ...................................................................................................................................................... 23

1) MENU CONSTITUTION TYPE ............................................................................................................................... 23

2) MAIN MENU CONSTITUTION (EXAMPLE)............................................................................................................. 24
3) SUB MENU CONSTITUTION (EXAMPLE) ............................................................................................................... 24
4) MENU CONSTRUCTION ...................................................................................................................................... 25
5) MENU ACCESS LEVEL ........................................................................................................................................ 26
6) STATUS ........................................................................................................................................................... 27
7) OPERATION ................................................................................................................................................... 28
8) SCHEDULE ..................................................................................................................................................... 29
9) RUNNING LOG ............................................................................................................................................... 30
9-1) Trip Message................................................................................................................................................................. 31
9-2) Alarm Message ............................................................................................................................................................. 32
9-3) Start Inhibit Message .................................................................................................................................................... 32
9-4) Running Log Message................................................................................................................................................... 33
9-5) Maintenance Message................................................................................................................................................... 33
10) MAINTENANCE ........................................................................................................................................... 34
11) SHUTDOWN.................................................................................................................................................. 35
12) ALARM MODE ............................................................................................................................................. 35
13) START INHIBIT ............................................................................................................................................ 35
14) COMPRESSOR ............................................................................................................................................. 36
15) VSD MODE (VARIABLE SPEED DRIVE CONTROL) – V MODEL ............................................................................ 37
16) TEST MODE .................................................................................................................................................. 38
17) CONFIGURE ................................................................................................................................................. 39
18) DIAGNISTIC ................................................................................................................................................. 40
19) SYSTEM DATE / TIME .................................................................................................................................. 41

5. HOW TO INSTALL ............................................................................................................................................................... 42

6. WIRING DIAGRAM – DX330L ........................................................................................................................................... 43

7. WIRING DIAGRAM – DX330M .......................................................................................................................................... 44

8. WIRING DIAGRAM – DX330V........................................................................................................................................... 45

-6-
UIC-DX330 Series User’s Manual Rev 2.0

※ Please check the product to the model ordering before usage.

Model Suffix Code Description

DX330 UIC for Screw Air-Compressor

- L Basic Model
Type - M Multi-Function Model
- V VSD Model
- Korean
- E English
Language
- C Chinese
- A Customer Language

※ Related Product Information.

Exclusive Temp. Sensor (DPR-TH02-06D100L) : Delivery Temp., Oil Reclaimer Temp.

Exclusive Temp. Sensor (DPR-TH1-ET) : Ambient Temp. Sensor
Pressure Sensor (DP500 Series) : Delivery Pressure, Oil Reclaimer Pressure
DX330 Exclusive Transformer : AC220V / AC24V
DX380 : Equipment Number Control Unit – Max. 8 units
DA-32 : Equipment Number Control System (Touch Screen Type), Max. 32 units
DA-100 : DX330 Monitoring & Trend System (Free of Charge)

※ Related Product Information

DX330 MODBUS RTU PROTOCOL MANUAL (PDF)

Pressure Sensor Data (PDF)
Temp. Sensor Data (PDF)
Wiring Diagram (PDF,DWG)

-7-
UIC-DX330 Series User’s Manual Rev 2.0

1. OUTLINE

UIC-DX330 is based on Micro Processor and the most advanced equipment for controlling electricity conducting efficient
operation of a screw air compressor. UIC-DX330 is a system managing the compressor’s operation intensively, saving energy
through controlling of timing for capacity adjustment, preventing problems in advance with alarming system and informing the
required preventative and maintenance schedule. In the other word, UIC-DX330 conducts the best operation (control)
according to the condition set up and operating circumstance.
Additionally, UIC-DX330 has VSD and PID function together as an option, so it is possible to reduce more than maximum
30% of energy cost.

▣ High reliability RISC MICOM

▣ Big size graphic LCD which is available for Korean/English/Chinese/Japanese
▣ Max 160 events of running log storable (Non-volatile) – Easy preventative & maintenance and analysis for trouble
▣ Automatic calculation and notice function for preventative & maintenance, consumable parts exchange information and
expected schedule
▣ Automation of economical operation by embedded weekly timer
▣ Various analogue outputs. (Inverter speed control, dispatch pressure transmission, delivery temperature transmission)

Unload pressure : Pressure value under unload operation with closing intake valve on compressor
Load pressure : Pressure value under load operation with opening intake valve on compressor
Load delay : Delay time when compressor starts load operation from starting
Re-load delay : Minimum delay time when compressor start load operation from unload operation
Auto stop delay : Compressor is stopped in case of continuous operation at unload operation during auto stop delay
time.
Manual stop delay : Compressor is stopped after unload operation during manual stop delay time.

-8-
UIC-DX330 Series User’s Manual Rev 2.0

1) Special Advantages
UIC-DX330 is a stable electronic control unit for screw air compressor which can provide users with multi-language
(currently Korean, English, Chinese and Japanese) display and running log for integral control and management of the
equipments. It adopts the method of digital process by high efficiency RISC type microprocessor and occupies enough
installation space and stability by unifying display module and control module. It provides convenience to let users know a
status of operation at once through display.

1-1) Noise Solution

It is inevitable to figure for noise as an industrial controller. The digital input and output signal of UIC-DX330 is
isolated, so it can not be allowed to flow external signal into the main board inside. Also, CPU on main board mounts
HARDWARE WATCHDOG TIMER which can automatically recover from CPU down occurred by noise per 32msec,
and BROWN-OUT function embedded in CPU inside supervises control power in real-time.

1-2) RISC TYPE MICOM

An assembler instruction in CPU can perform 7.3728Mbps, and logic for controlling written in CPU inside needs about
1 msec based on 1 cycle. In this regard, sampling rate is about 10 times faster than the existing controllers, so it has less
probability of malfunction and more precise control.

1-3) Black Box : A recorder of operation status

It is possible for UIC-DX330 to store maximum until 160 events of running log, so it is easy for preventative &
maintenance and trouble-shooting. Additionally, it is possible to verify the operation data at site when trip occurs, so it is
helpful for users to know the reason of trouble and the status of equipment in real-time.

1-4) Display for operation status and/or maintenance information (trip computer)

UIC-DX330 has the display function for operation status, delay time and ready time by counting reversely, so users can
recognize the status of compressor at a glance. Also, it has the basic function to notify parts and oil checking and
exchanging schedule by calculating it automatically according to the information of operation.

1-5) Big Size Graphic LCD (Wide Temperature Range Type : -20 ~ +70℃)

Display part of UIC-DX330 adopts big size graphic LCD for user’s easy operation and recognition. (Currently
applicable for Korean, English, Chinese and Japanese)

1-6) Minimization

It is possible to minimize compressor by occupying a small space due to unifying design of control part and display part.

1-7) Scalability
It provides users with RS485 port, MODBUS RTU standard protocol and MMI software and automatic interface.

-9-
UIC-DX330 Series User’s Manual Rev 2.0

2) Basic Specification

2-1) General Specification

Input Power AC24V 50/60Hz, DC24V
Power Conditions
Power Consumption Max. 20VA

2-2) CPU & LCD

CPU AT mega 128, 16MHz
CPU, LCD
LCD 240 X 128 pixel, LED Backlight

2-3) Digital Input & Output

Input Type Opto-Isolation
Digital Input Number of Input 10Points (5 X 2 Common)
Signal Power AC24V or DC24V
Output Type Relay Contact
Digital Output Number of Output 12Points (4 X 3 Common)
Relay Contact Type 250V, 10A

2-4) Analogue Input & Output

Temp. Sensor NTC 3 Points
Analog Input 4~20mAdc 2 Points (Internal Sensor Power 24V)
Correction of Deviation Software
Number of Channel 3 Channels
Analog Output Output Type 4~20mA
Setup Type Software

2-5) Communication Specification

Type RS485(Half-Duplex), 1 Channel (Modbus RTU)
4800, 9600, 19200, 38400 BPS (default 9600)
Speed
Communication Parity None, Data 8bit, Stop 1bit
Distance Max. 1.2Km
Recommended Cable BELDEN 9842 or 8761

2-6) Installation Circumstance

Place Indoor
Installation Operation Temp. -10 ~ 60 ℃
Circumstance Storage Temp. -30 ~ 80 ℃
Operation Humidity 5~95% (No condensation)

- 10 -
UIC-DX330 Series User’s Manual Rev 2.0

2. Input / Output Specification

1) Digital Input Signal

Pin Name Function Active state

J13.1 ID1 Emergency Stop S/W Signal Fault (open)

J13.2 ID2 Overload Fan Motor Signal Fault (open)

J13.3 ID3 Overload Main Motor Signal Fault (open)

J13.4 ID4 Reverse Phase Unit Signal Fault (open)

J13.5 ID5 Reserved Input Signal

J13.6 IDC1 Input Common Terminal 1

Pin Name Function Active state

J14.1 ID6 Oil-Filter High DP Alarm Signal Alarm (closed)

J14.2 ID7 Air-Filter High DP Alarm Signal Alarm (closed)

J14.3 ID8 Oil Reclaimer DP Alarm Signal Alarm (closed)

J14.4 ID9 Remote Load/Unload Control Remote (closed)

J14.5 ID10 Remote Start/Stop Control Run (closed)

J14.6 IDC2 Input Common Terminal 2

- 11 -
UIC-DX330 Series User’s Manual Rev 2.0

2) Digital Output Signal

Pin Name Function Active state

J21.1 N1 -

J21.2 N2 -

J21.3 N3 -

J21.4 N4 Load Solenoid Control ON

J21.5 C1 Output Common Terminal 1

Pin Name Function Active state

J22.1 N5 Main Magnetic Contactor ON

J22.2 N6 Star Magnetic Contactor ON

J22.3 N7 Delta Magnetic Contactor ON

J22.4 N8 -

J22.5 C2 Output Common Terminal 2

Pin Name Function Active state

J23.1 N9 Multi Function Port N9

J23.2 N10 Multi Function Port N10

J23.3 N11 Multi Function Port N11

J23.4 N12 Multi Function Port N12

J23.5 C3 Output Common Terminal 3

※ N9~N12 Functions are applicable from “M” models.

- 12 -
UIC-DX330 Series User’s Manual Rev 2.0

3) Analogue Input Signal

Pin Name Function Type Range

J11.1 +VDC Sensor Power (+V Common)

J11.2 B4 Delivery Press. Sensor Input 4~20mA Settable
J11.3 B5 Oil Reclaimer Press. Sensor Input 4~20mA Settable
J11.4 GND 0V Common (Earthing of Shield Wire)
Î Oil reclaimer sensor input is applicable from “M” models.

Pin Name Function Type Range

J12.1 B1 Delivery Temp. Sensor Input NTC 10K -30 ~ 200 ℃

J12.2 GND 0V Common
J12.3 B2 Ambient Temp. Sensor Input NTC 5K -30 ~ 200 ℃
J12.4 GND 0V Common
J12.5 B3 Oil Reclaimer Temp. Sensor Input NTC 10K -30 ~ 200 ℃
Î Oil reclaimer temp. sensor input and ambient temp. sensor input are applicable from “M” model.

- 13 -
UIC-DX330 Series User’s Manual Rev 2.0

4) Analogue Output Signal

Pin Name Function Type

J6.1 Y1 Inverter Speed Output Signal (in case of VSD Control) 4 ~ 20mA
J6.2 YG1 Inverter Speed Control Output Common (0 ~ 100%)
J6.3 Y2 Delivery Press. Transmission Signal 4 ~ 20mA
J6.4 YG2 Delivery Press. Transmission Signal Common ※ (Range Setup)
J6.5 Y3 Delivery Temp. Transmission Signal 4 ~ 20mA
J6.6 YG3 Delivery Temp. Transmission Signal Common (-10 ~ 150℃)
Î Analogue output signal is application from “V” model.
※ Discharge air press. transmission signal outputs retransmission signal (4~20mA) as the input range of
[configuration, discharge press. low, discharge press. high].

- 14 -
UIC-DX330 Series User’s Manual Rev 2.0

5) Communication Signal

5-1) SYSTEM BUS

Pin Name Function Type

TB1.1 SG -
TB1.2 B SYSTEM BUS TRX- RS-485
TB1.3 A SYSTEM BUS TRX+

5-2) LOCAL BUS

Pin Name Function Type

TB2.1 SG -
TB2.2 B LOCAL BUS TRX- RS-485
TB2.3 A LOCAL BUS TRX+

※ Communication Signal (System Bus, Local Bus Common)

① Communication Type : RS-485
② Communication Speed : 4800, 9600, 19200, 384000 BPS, N, 8, 1, default 9600bps
③ Communication Protocol : MODBUS RTU MODE
④ Recommended Communication Cable : BELDEN 9842 or 8761

BELDEN 9842 Paired- Low Capacitance EIA RS-485

⊙ Number of Pairs: 2
⊙ Total Number of Conductors: 4
⊙ AWG: 24
⊙ Stranding: 7x32
(9842) ⊙ Conductor Material: TC - Tinned Copper
⊙ Insulation Material: PE - Polyethylene
⊙ Outer Shield Material Trade Name: Beldfoil®
⊙ Outer Shield Material: Aluminum Foil-Polyester Tape/TC –
⊙ Tinned Copper
⊙ Outer Jacket Material: PVC - Polyvinyl Chloride
⊙ Plenum (Y/N): N ⊙Plenum Number: 82842
(8761) ⊙ Applications: Computer Cables, Low Capacitance EIA RS-485

※ BELDEN 9842 standard cable is recommendable.

- 15 -
UIC
C-DX330 Serries User’s Manual
M Rev 2.0

6) Coontrol Poweer Input

Pin N
Name Function
n Type

J1.1 FG FIELD GROUND (C

CASE SHIELD
D)
J1.2 G0 A
AC24V(-) or DC24V(-)
D
J1.3 G A
AC24V(+) or DC24V(+)
D

(Power Input
I Wiring Diagram)
D

- 16 -
UIC-DX330 Series User’s Manual Rev 2.0

3. Constitution
1) Operation and Display Part

1-1) Basic Constitution

Display Part Specification : 240 X 128 Graphic LCD (LED BACKLIGHT), LED Green 1EA, Red 1EA
Keyboard : Membrane Keypad Switch (8EA)

1-2) Operation Part

Start Switch : Start
Stop Switch : Stop
Reset : Reset when trip occurred
Green Ramp 1 : Ramp showing status of operation
Red Ramp 2 : Ramp showing trip or warning

1-3) Program Setup Part

Select Switch : Selection of setup program or value
Downward Switch : Moving down to setup program or value
Upward Switch : Moving up to setup program or value
Menu Switch : Opening menu for setup
Reset Switch : Returning to the previous menu or initial screen]

- 17 -
UIC-DX330 Series User’s Manual Rev 2.0

2) Measurements and Mount Information

- 18 -
UIC-DX330 Series User’s Manual Rev 2.0

3) Display for Operation Status

If you push “ENTER”, it is displayed operation time, loading time, ratio of loading/unloading duty, ambient temp.,
oil reclaimer temp, oil reclamier press. Inverter output and frequency respectively.

4) Operation Button Function

Select Start / Stop

The equipment starts when pushing start button (Green).
Start / Stop
The equipment stops when pushing stop button (Red).

Reset when trip

Reset
The trip reset automatically doesn’t need to push reset button.

Menu It returns to setup and status menu when pushing menu button

Enter Choice and storage

Up / Down Upward (Increase) and/or Downward (Decrease)

Cancel Return to the previous menu or initial screen

- 19 -
UIC-DX330 Series User’s Manual Rev 2.0

5) Status Display Ramp

Operation Status ON / OFF according to operation status

Green

Alarm Status ON / OFF according to alarm status

Red

ON : LED is always on.

Low speed flickering : On for 0.5 sec./ Off for 0.5 sec.
High speed flickering : On for 0.1 sec./ Off for 0.1 sec.
Spot flickering : On for 0.1 sec. / Off for 4 sec.
OFF : LED is always off.

No. Status
Operation Status Ramp Alarm Status Ramp
00 Initialization OFF
01 Operation Inhibit OFF
02 Operation Ready OFF
Spot Flickering
Start Delay
03 Load Operation Request Status : High
(Blowdown check)
Speed Flickering
Normal : OFF
04 Start Ready Spot Flickering
Trip : High Speed
Spot Flickering
During Operation Flickering
06 Load Operation Request Status : High
(Y/D transfer delay) Alarm : Low Speed
Speed Flickering
Flickering
Spot Flickering
Maintenance : Spot
07 Load Operation Delay Load Operation Request Status : High
Flickering
Speed Flickering
Start Inhibit : Spot
08 Load Operation ON
Flickering
Spot Flickering
09 Reload Delay Load Operation Request Status : High
Speed Flickering
10 Auto-stop Delay Spot Flickering
11 Manual-stop Delay Low Speed Flickering
99 Shut-down OFF

- 20 -
UIC-DX330 Series User’s Manual Rev 2.0

6) Symbol Explanation

6-1) Equipment Status Display

Start / Stop Mode Status Display

LOC : Start /Stop using start / stop key on the equipment
NET : Start / Stop from PC or remote device using protocol
REM : Start / Stop remotely using digital input port on the equipment
SCH : Start / Stop according to setup schedule of [Schedule] menu
Load Operation Mode Display
LOC : Load / Unload operation by press. value of sensor on the equipment
NET : Load / Unload operation from PC or remote device using protocol
REM : Load / Unload operation remotely using digital input port on the equipment
Stop Status Display
Display during equipment’s stop
LOC STOP : Stop by stop button on the equipment
REM STOP : Stop by digital input
NET STOP : Stop by communication function
SCH STOP : Stop by setup time on [Schedule] menu
S.D STOP : Stop when trip occurred

Operation Status Display

Display during equipment’s operation
LOC RUN : Operate by start button on the equipment
REM RUN : Operate by digital input
NET RUN : Operate by communication function
SCH RUN :Operate by setup time on [Schedule] menu

Equipment Status Display

GOOD : Normal status
MAINTEN : Required maintenance
ALARM : Alarm status
S-DOWN : Sensing fault
INHIBIT : Start inhibit

System Lock Signal

- 21 -
UIC-DX330 Series User’s Manual Rev 2.0

6-2) Digital Input Signal

Symbol Description Symbol Description

Emergency Stop S/W Fault Signal Oil-Filter High DP Alarm Signal

Overload Fan Motor Fault Signal Air-Filter High DP Alarm Signal

Overload Main Motor Fault Signal Oil Reclaimer DP Alarm Signal

Reverse Phase Unit Fault Signal Remote Load/Unload Control

Spare Input Port Remote Start/Stop Control

6-3) Digital Output Signal

Symbol Description Symbol Description

Main Magnetic Contactor Multi Function Port N9

Star Magnetic Contactor Multi Function Port N10

Delta Magnetic Contactor Multi Function Port N11

Load Solenoid Control Multi Function Port N12

- 22 -
UIC-DX330 Series User’s Manual Rev 2.0

4. Menu Constitution
1) Menu Constitution Type

Main Manu

Sub Menu

Parameter

- 23 -
UIC-DX330 Series User’s Manual Rev 2.0

2) Main Menu Constitution (Example)

※ Showing menu might be slightly different from “V” model.

3) Sub Menu Constitution (Example)

- 24 -
4) Menu Construction
(Based on ‘M’ model) * mark is applicable for ‘ V ’ model only.

STATUS OPERATION SCHEDULE RUNNING LOG. MAINTENANCE SHUTDOWN ALARM MODE

00: Discharge Temp. 00: Unload Pressure 00: Sun : Start ~ Stop 00:Event #1 00: Dust Filter Cleaning 00: Discharge Temp High 00: Discharge Temp High
01: Discharge Press. 01: Load Pressure 01: Mon : Start ~ Stop 01:Event #2 01: Suction Filter Change 01: Discharge Press High 01: Discharge Press High
02: Ambient Temp.* 02: Auto-Stop Delay Time 02: Tue : Start ~ Stop 02:Event #3 02: Oil Filter Change 02: Oil Reclaimer Temp 02: Oil Reclaimer Temp
03: Oil Reclaimer Press. 03: Stop Delay Time 03: Wed : Start ~ Stop | 03: Lub. Oil Change High* High*
04: Oil Reclaimer Temp.* 04: Blowdown Delay 04: Thu : Start ~ Stop 03:Event #160 04: Cooler Cleaning 03: Oil Reclaimer Press 03: Oil Reclaimer Press
05: Differential Press. Time 05: Fri : Start ~ Stop 05: Overhaul High* High
06: Total Run Hours 05: Drain Time [On] 06: Sat : Start ~ Stop 04: Diff-Pressure High 04: Diff- Pressure High
07: Motor Run Hours 06: Drain Interval [Off] 05: Ambient Temp High*
08: Motor On/Off Times 07:Cooling Fan Run
09: Loaded Hours Temp*
10: Loaded On/Off Times 08: Cooling Fan Stop
11: Inverter Control* Temp* CONFIGURE DIAGNOSTIC
12: Discharge Press .
09: LCD Backlight Mode
Retrans. *
13: Discharge Temp. 00: Master Password 00: SELF TEST
Retrans.* VSD MODE* TEST MODE Setup 01: B1 Input
01: Trip/Alarm History 02: B2 Input
Delete 03: B3 Input
00: VSD Control Mode 00: Manual Test Mode
02: Operation History 04: B4 Input
01: Maximum Speed 01: Main Motor MAIN
Delete 05: B5 Input
02: Minimum Speed 02: Main Motor STAR
03: Ambient Temp Sensor 06: B4 4mA
COMPRESSOR 03: Optimum Speed 03: Main Motor DELTA
Use 07: B4 20mA
04: Unloaded Speed 04: Load SOL. Valve
04: Oil Press. Use 08: B5 4mA
00: Y-DELTA Transfer 05: Speed Command(Hz) 05: Multi Function N9
START INHIBIT 05: Oil Temp. Use 09: B5 20mA
Time 06: Speed Command(mA) 06: Multi Function N10
06: Discharge Press 10: Y1 4mA*
01: Load Delay Time 07: Proportional Band(P) 07: Multi Function N11
Correct 11: Y1 20mA*
00: Discharge Temp Low 02: Reload Delay Time 08: Integral Time (I) 08: Multi Function N12
07: Oil Press. Correction 12: Y2 4mA*
01: Oil Reclaimer Press 03: Diff. Press Detect 09: Dead Band 09: Inverter Control*
08: Ambient Temp. 13: Y2 20mA*
High Delay 10: Jerk Control Ratio 10: Discharge Press
Correction* 14: Y3 4mA*
04: Load Command Mode 11: Max. Inverter RPM Retrans.*
12: Max. Inverter Frequency
09: Discharge Temp. 15: Y3 20mA*
05: Starting Command 11: Discharge Temp
Correct 16: ADC F/T
Mode Retrans* 10: Oil Temp. Correction* 17: DAC F/T
06: Power Return Restart 11: Discharge Press Min
07: Network ID 12: Discharge Press Max
08: Network BPS 13: Min. Oil Press.
14: Max. Oil Press.
15: Multi Function N9
16: Multi Function N10
17: Multi Function N11
18: Multi Function N12
UIC-DX330 Series User’s Manual Rev 2.0

5) Menu Access Level

Access USER SERVICE1 SERVICE2 SERVICE3

Level (CODE = 0009) (CODE = 0100) (CODE = 0119) (CODE = ****)
1.STATUS 1.STATUS 1.STATUS 1.STATUS
2.OPERATION 2.OPERATION 2.OPERATION 2.OPERATION
3.RUNNING LOG 3.RUNNING LOG 3.SCHEDULE 3.SCHEDULE
4.MAINTENANCE 4.MAINTENANCE 4.RUNNING LOG 4.RUNNING LOG
5.SHUTDOWN 5.SHUTDOWN 5.MAINTENANCE 5.MAINTENANCE
6.ALARM MODE 6.ALARM MODE 6.SHUTDOWN 6.SHUTDOWN
Accessible
7.START INHIBIT 7.START INHIBIT 7.ALARM MODE 7.ALARM MODE
Menu
8.COMPRESSOR 8.START INHIBIT 8.START INHIBIT
9.VSD MODE* 9.COMPRESSOR 9.COMPRESSOR
10.TEST MODE 10.VSD MODE* 10.VSD MODE*
11.CONFIGURE 11.TEST MODE 11.TEST MODE
12.CONFIGURE 12.CONFIGURE
13.DIAGNOSTIC 13.DIAGNOSTIC
Lasting
1 min. 10 min. 30 min. 1 hr.
Time
When changing Access Level Mode, make locked by putting [Cancel] button for 3 seconds.

① If putting [Menu] on operating display, it shows access code input display below.
(If putting [Menu] during supporting time, it does not ask Access Code.)
② After input Access Code by [Upward]/[Downward] key, put [Enter] and then, convert to Menu display.

<Display of Access Code Input>

③ If Access Level is under [Service] level 1, [Set expanded operation] parameter does not change.
④ When changing lock mode before lasting time, please push [Cancel] button for 3 seconds.

-26-
UIC-DX330 Series User’s Manual Rev 2.0

6) STATUS

Item Description Units Step Min Max Default

000 Discharge Temp. ℃

001 Discharge Press. Bar
002 Ambient Temp.*** ℃
**
View Only
003 Oil Reclaimer Press. Bar
004 Oil Reclaimer Temp.** ℃
005 Differential Press.** Bar
*
006 Total Run Hours H 1 0 99999
007 Motor Run Hours* H 1 0 99999
008 Motor On/Off Times* T 1 0 99999
*
009 Loaded Hours H 1 0 99999
010 Loaded On/Off Times* T 1 0 99999
011 Inverter Control mA
012 Discharge Press. Retrans. mA View Only
013 Discharge Temp. Retrans. mA
*
Times and Hours are automatically initialized and counted from “0” in case of over “99999”.
*
Times and Hours are changeable over [Service 2]level.
**
Oil Reclaimer Pressure and Temperature are displayed only in case of setting [Use]of related item on Menu.
***
Ambient Temperature is displayed only in case of setting [On] on [CONFIGURE:Ambient Temp. Sensor].
**
Differential Pressure = Oil Reclaimer Pressure – Discharge Pressure

- 27 -
UIC-DX330 Series User’s Manual Rev 2.0

7) OPERATION

Item Description Units Step Min Max Default View Access

100 Unload Pressure bar 0.1 4.0 70.0 8.6 bar USER1 SVC1
101 Load Pressure bar 0.1 3.8 65.0 6.5 bar USER1 SVC1
102 Auto-Stop Delay Time S 1 1 3600 300 S USER1 SVC1
103 Stop Delay Time S 1 1 60 30 S USER1 SVC1
104 Blowdown Delay Time S 1 1 600 10 S USER1 SVC1
**
105 Drain Time [On] S 1 1 30 5S USER1 SVC1
106 Drain Inteval** S 1 1 3600 60 S USER1 SVC1
107 Cooling Fan Run Temp*** ℃ 1 0 200 80 ℃ USER1 SVC1
108 Cooling Fan Stop Temp ***
℃ 1 0 200 70 ℃ USER1 SVC1
**
It is displayed only in case of setting [Use]of drain function on [CONFIGURE : Multi Function].
***
It is displayed only in case of setting [Use]of cooling fan function on [CONFIGURE : Multi Function].

① Unload Pressure :
z It cannot be set under +0.2bar of loaded pressure value.
z It cannot be set over -0.2bar of alarm pressure value.
② Load Pressure : It cannot be set over -0.2 bar of unload pressure value.
③ Temperature Sensing Capacity : Control(0.01℃), Display(0.1℃)
④ Pressure Sensing Capacity : Control(0.01bar), Display(0.1bar)
⑤ Cooling Fan Run Temp. : Temperature when cooling fan is under operation. (It is recommended to be set more
than 2℃ than cooling fan stop temperature)
⑥ Cooling Fan Stop Temp. : Temperature when cooling fan stops. (It is recommended to be set less than 2℃ than
cooling fan run temperature.)

- 28 -
UIC-DX330 Series User’s Manual Rev 2.0

8) SCHEDULE

Item Description RUN ~ STOP

400 SUN 00 : 00 ~ 00 : 00

401 MON 08 : 30 ~ 18 : 30

402 TUE 08 : 30 ~ 18 : 30

403 WED 08 : 30 ~ 18 : 30

404 THU 08 : 30 ~ 18 : 30

405 FRI 08 : 30 ~ 18 : 30

406 SAT 08 : 30 ~ 12 : 30

※ It is applied and displayed only in case of setting of [Schedule Operation] on [Extend Operation] menu.

※ It is applicable over ‘M’ model.

① It is used in case of start and stop at indicated time.

② The equipment is automatically operated at run time and stopped at stop time.
③ In case of no operation on specific day, run time and stop time are set the same.
④ If run time is after stop time, the equipment shall not be operated.
⑤ It is possible to run & stop by pushing [Run] and [Stop] button during schedule operation. (See the following
picture)
⑥ The equipment shall not be operated after stop time, although pushing [Run] button. (See the following picture).

- 29 -
UIC-DX330 Series User’s Manual Rev 2.0

9) RUNNING LOG
Occur /
Item Date Time Event
Reset
1 YY/MM/DD H H : M M ( X ) Event #1
2 YY/MM/DD H H : M M ( X ) Event #2
3 YY/MM/DD H H : M M ( X ) Event #3
4 YY/MM/DD H H : M M ( X ) Event #4
5 YY/MM/DD H H : M M ( X ) Event #5
| | | | |
160 YY/MM/DD H H : M M ( X ) Event #160

※ It is impossible to modify and/or delete the contents of event at the option.

① When trip alarm occurs (resets), date and history of event are stored at non volatile memory.
② The maximum number of storable event is 160EA and it is deleted the earliest event and stored the lastest
one in case of over 160EA.
③ When trip alarm is occurred, [Date, Time and Event] is recorded. Also, when trip alarm is reset, “X” mark is
showed next to [Time].
④ When pushing [Enter] button, you can see operation status code, discharge pressure, discharge temperature
and ambient temperature when trip alarm occurs.
(Screen for Trip Alarm Status)

If pushing [MENU] button, you can see the latest alarm history on screen for [Trip Alarm Status].

Discharge Air Status + Whole Status Oil Reclaimer Status + Whole Status

If pushing [MENU] button, you can see the status of discharge air and oil reclaimer in shifts.
(In case of installation of sensor for oil reclamier pressure or temperature)

- 30 -
UIC-DX330 Series User’s Manual Rev 2.0

9-1) Trip Message

Item Description Detect condition

1 System Fault In case of unexpected change of the value of parameter

Sensing [Digital Signal Input : Emergency Stop] : ON

2 Emergency Stop
Reset [Digital Signal Input : Emergency Stop] : OFF

Sensing [Digital Signal Input : Fan Motor O.L] : ON

3 Fan Motor O.L.
Reset [Digital Signal Input : Fan Motor O.L] : OFF

Sensing [Digital Signal Input : Main Motor O.L : ON

4 Main Motor O.L
Reset [Digital Signal Input : Main Motor O.L : OFF

Sensing [Digital Signal Input : Reverse Phase] : ON

5 Reverse Phase
Reset [Digital Signal Input : Reverse Phase] : OFF

Discharge Press. Sensing Discharge Press. [Alarm Mode : Discharge Press. High]
6
High Reset Discharge Press. < [Alarm Mode : Discharge Press. High] - 0.5bar

Discharge Temp. Sensing Discharge Temp. [Alarm Mode : Discharge Temp. High]
7
High Reset Discharge Temp. < [Alarm Mode : Discharge Temp. High] - 5℃

Oil Reclaimer Sensing Oil Reclaimer Press. [Alarm Mode : Oil Reclaimer Press. High]
8
Press. High Reset Oil Reclaimer Press. < [Alarm Mode : Oil Reclaimer Press. High] – 0.5bar

Oil Reclaimer Sensing Oil Reclaimer Temp. [Alarm Mode : Oil Reclaimer Temp. High]
9
Temp. High Reset Oil Reclaimer Temp. < [Alarm Mode : Oil Reclaimer Temp. High] - 5℃
Sensing (Oil Reclaimer Press.–Discharge Press.) [Alarm Mode:Diff. Press. High] &

10 Diff. Press. High Discharge Air Temp. > 50℃

Reset (Oil Reclaimer Press.–Discharge Press.) < [Alarm Mode:Diff.Press.High] - 0.1bar

Browdown Time Oil Reclaimer Press. > [Start Inhibit : Oil Reclaimer Press. High] in case of exceeding of
11
Over [Operation : Blowdown Delay Time] during browdown check sequenc.

Discharge Sensing In case of occurrence of error on discharge press. sensor (disconnection / short)
12
P-Sensor Reset In case of normal condition of discharge press. sensor

Discharge Sensing In case of occurrence of error on discharge temp. sensor (disconnection / short)
13
T-Sensor Reset In case of normal condition of discharge temp. sensor

Sensing In case of occurrence of error on oil reclaimer press. sensor (disconnection / short)
14 Oil P-Sensor Fault
Reset In case of normal condition of oil reclaimer press. sensor

Sensing In case of occurrence of error on oil reclaimer temp. sensor (disconnection / short)
15 Oil T-Sensor Fault
Reset In case of normal condition of oil reclaimer temp. sensor

Sensing In case of occurrence of error on ambient temp. sensor (disconnection / short)

16 Ambient T-Sensor
Reset In case of normal condition of ambient temp. sensor

※ Fault message occurred is reset by pushing [Reset] button after solving related reason.

- 31 -
UIC-DX330 Series User’s Manual Rev 2.0

9-2) Alarm Message

Item Description Detect condition

Oil Filter Sensing [Digital Signal Input : Oil Filter Diff. Press] : ON
1
Diff. Press. Reset [Digital Signal Input : Oil Filter Diff. Press] : OFF

Air Filter Diff. Sensing [Digital Signal Input : Air Filter Diff. Press] : ON
2
Press. Reset [Digital Signal Input : Air Filter Diff. Press] : OFF

Oil Reclaimer Sensing [Digital Signal Input : Oil Reclaimer Diff. Press] : ON
3
Diff. Press. Reset [Digital Signal Input : Oil Reclaimer Diff. Press] : OFF

Discharge Press. Sensing Discharge Press [Alarm Mode : Discharge Press. High]
4
High Reset Discharge Press < [Alarm Mode : Discharge Press. High]-0.5bar

Discharge Temp. Sensing Discharge Temp. [Alarm Mode : Discharge Temp. High]
5
High Reset Discharge Temp. < [Alarm Mode : Discharge Temp. High]-5℃

Oil Reclaimer Sensing Oil Reclaimer Press [Alarm Mode : Oil Reclaimer Press. High]
6
Press. High Reset Oil Reclaimer Press < [Alarm Mode : Oil Reclaimer Press. High]-0.5bar

Oil Reclaimer Sensing Oil Reclaimer Temp. [Alarm Mode : Oil Reclamier Temp. High]
7
Temp. High Reset Oil Reclaimer Temp. < [Alarm Mode : Oil Reclaimer Temp. High]-5℃

Sensing (Oil Reclaimer Press–Discharge Press) [Alarm Mode:Diff. Press High] & Discharge Gas Temp. > 50℃
8 Differential Press
Reset (Oil Reclaimer Press-Discharge Press) < [Alarm Mode:Diff Press. High]-0.1bar

Ambient Temp. Sensing Ambient Temp. [Alarm Mode : Ambient Temp. High]
9
High Reset Ambient Temp. < [Alarm Mode : Ambient Temp. High]-5℃

RTC Function Sensing RTC is not working, (Sensible during scheduled operation)
10
Incapacity Reset RTC is in ordinary operation, (necessary to reset the time)

※ Occurred alarm message is automatically reset in case of reset condition.

9-3) Start Inhibit Message

Item Description Detect condition

Discharge Temp. Sensing Discharge Temp. < [Start Inhibit-Discharge Temp. Low]
1
Low Reset Discharge Temp. > [Start Inhibit-Discharge Temp. Low]

Oil Reclaimer Sensing Oil Reclaimer Press > [Start Inhibit-Oil Reclaimer Press High]
2
Press High Reset Oil Reclaimer Press < [Start Inhibit-Oil Reclaimer Press High]

※ The equipment doesn’t operate when start inhibit alarm occurs, and it automatically starts when the alarm is reset..

- 32 -
UIC-DX330 Series User’s Manual Rev 2.0

9-4) Running Log Message

Item Description Detect condition

Initial Power
1 Initial Power Input Time (It cannot be deleted.)
Input

2 Main Power Input Power Input Time, (In case of system recovery by WATCH DOG timer)

3 Operation Start Operation Start Time

4 Operation Stop Operation Stop Time

※ It is recorded in Running Log.

9-5) Maintenance Message

Item Description Detect condition

Dust Filter
1 In case of exceeding dust filter cleaning cycle
Cleaning

Suction Filter
2 In case of exceeding suction filter change cycle
Change

3 Oil Filter Change In case of exceeding oil filter change cycle

4 Lub. Oil Change In case of exceeding lub. oil change cycle

5 Cooler Cleaning In case of exceeding cooler cleaning cycle

6 Overhaul In case of exceeding overhaul cycle

- 33 -
UIC-DX330 Series User’s Manual Rev 2.0

10) MAINTENANCE

Item Description Units Step Min Max Default View Access

Dust Filter Cleaning

400 h 1 0 32000 500 h USER1 SVC1
(Till, Cycle, Pass, Exceed)
Suction Filter Change
401 h 1 0 32000 4000 h USER1 SVC1
(Till, Cycle, Pass, Exceed)
Oil Filter Change
402 h 1 0 32000 8000 h USER1 SVC1
(Till, Cycle, Pass, Exceed)
Lub. Oil Change
403 h 1 0 32000 8000 h USER1 SVC1
(Till, Cycle, Pass, Exceed)
Cooler Cleaning
404 h 1 0 32000 6000 h USER1 SVC1
(Till, Cycle, Pass, Exceed)
Overhaul
405 h 1 0 32000 9000 h USER1 SVC1
(Till, Cycle, Pass, Exceed)
▣ In case of not using some items, please put cursor on the item and push [RESET] button at cycle mode.

▣ In case of resetting some items, please put cursor on the item and push [RESET] button at till·exceed, pass mode.

▣ You can see cycle, till·exceed, pass mode in order in case of pushing [Menu] button.

How to setup (Example : Dust Filter Cleaning)

Dust Filter Cleaning Dust Filter Cleaning Dust Filter Cleaning

Till 100 h Cycle 100 h Pass 400 h

Dust Filter Cleaning Dust Filter Cleaning

Cycle 600 h Pass 200 h

Dust Filter Cleaning Dust Filter Cleaning

Till 200 h Till 300 h

Parameter setup complete Parameter setup complete

- 34 -
UIC-DX330 Series User’s Manual Rev 2.0

11) SHUTDOWN

Item Description Units Step Min Max Default View Access

500 Discharge Temp. High ℃ 1 80 130 120 ℃ USER1 SVC1

501 Discharge Press. High bar 0.1 1.2 100.0 8.0 bar USER1 SVC1
502 Oil Reclamier Temp. High *
℃ 1 80 130 120 ℃ USER1 SVC1
**
503 Oil Reclaimer Press High bar 0.1 1.2 100.0 9.0 bar USER1 SVC1
504 Diff-Pressure High** bar 0.1 0.4 5.0 1.0 bar USER1 SVC1
*
It is only displayed in case of setting ON at [Alarm Mode-Oil Reclaimer Temp. Use].
**
It is only displayed in case of setting ON at [Alarm Mode-Oil Reclaimer Press. Use].
※ Trip press. value cannot be set over the maximum value of pressure sensor.

12) ALARM MODE

Item Description Units Step Min Max Default View Access

600 Discharge Temp. High ℃ 1 80 130 110 ℃ USER1 USER2

601 Discharge Press. High bar 0.1 1.2 100.0 7.6 bar USER1 USER2
602 Oil Reclaimer Temp. High* ℃ 1 80 130 110 ℃ USER1 USER2
**
603 Oil Reclaimer Press High bar 0.1 1.2 100.0 8.6 bar USER1 USER2
604 Diff-Pressure High** bar 0.1 0.4 5.0 0.8 bar USER1 USER2
605 Ambient Temp. High ℃ 1 35 60 40 ℃ USER1 USER2
*
It is only displayed in case of setting ON at [Alarm Mode-Oil Reclaimer Temp. Use].
**
It is only displayed in case of setting ON at [Alarm Mode-Oil Reclaimer Press. Use]..
※ Alarm press. value cannot be set over -0.2bar of trip press. value or under +0.2bar of unload operation
press.
※ Alarm temp. value cannot be set over -2℃ of trip temp. value.

13) START INHIBIT

Item Description Units Step Min Max Default View Access

700 Discharge Temp. Low ℃ 1 -10 10 1℃ USER1 USER2

701 Oil Reclaimer Press. High** bar 0.1 0.1 5.0 0.5 bar USER1 USER2
**
It is only displayed in case of setting ON at [Alarm Mode-Oil Reclaimer Press. Use].
※ Oil reclaimer press high value cannot be set over the maximum value of oil reclaimer press. sensor.

- 35 -
UIC-DX330 Series User’s Manual Rev 2.0

14) COMPRESSOR

Item Description Units Step Min Max Default View Access

800 Y-DELTA Transfer Time Sec 0.1 0.0 30.0 6.0 Sec USER1 SVC2
801 Load Delay Time Sec 1 5 300 10 Sec USER1 SVC2
802 Reload Delay Time Sec 1 5 300 10 Sec USER1 SVC2
803 Diff. Press Detect Delay Sec 1 1 600 10 Sec USER1 SVC2
804 Load Command Mode - Local / Network / Remote Local USER1 SVC2
805 Starting Command Mode - Local / Network / Remote / Schedule Local USER1 SVC2
806 Power Return Restart - ON/OFF ON USER1 SVC2
807 Network ID** - 1 1 127 1 USER1 SVC2
**
808 Network BPS - 4800, 9600, 19200, 38400 9600 USER1 SVC2
**
It is only displayed in case of installing communication port option.

14-1) Starting Command Mode (Setup of control source for equipment run/stop)
① Local : Run/Stop using keypad on controller itself.
② Network : Run/Stop using system network.
③ Remote : [Stop : Digital Input Signal (ID10) : OFF Æ ON], [Run : Digital Input Signal : ONÆOFF],
Edge Detection Method (It is possbile to run or stop by network or keypad)
④ Schedule : Operation during the setup time on [Schedule] menu
(It is possible to run or stop by network or keypad)

14-2) Load Command Mode (Setup of control source of equipment load run)
① Local : Using press. value from press. sensor.
② Network : Run/Stop using system network
③ Remote : [Load Run : Digital Input Signal (ID9) : ON], [Unload Run : Digital Input Signal : OFF]

14-3) Power Return Restart [Run/Stop Command in case of power return after mains failure
① Power Return Function : ON
- Mains failure during operation Æ Power return : Run
- Mains failure during stop Æ Power return : Stop
② Power Return Function : OFF.
- Mains failure during operation : Power return : Stop
- Mains failure during stop : Power return : Stop

14-4) If Y-DELTA transfer time is set as ‘0.0’sec., the equipment operates direct start mode.

- 36 -
UIC-DX330 Series User’s Manual Rev 2.0

15) VSD MODE (Variable Speed Drive Control) – V Model

Item Description Units Step Min Max Default View Access

900 VSD Control Mode - OFF / FIX / VSD OFF USER1 SVC2
901 Maximum Speed rpm 10 0 9990 3600 USER1 SVC2
902 Minimum Speed rpm 10 0 9990 1500 USER1 SVC2
903 Optimum Speed rpm 10 0 9990 2700 USER1 SVC2
904 Unloaded Speed rpm 10 0 9990 1800 USER1 SVC2
905 Speed Command(Hz) Hz View only USER1 LOCK
906 Speed Command(mA) mA View only USER1 LOCK
907 Proportional Band (P) % 0.1 0.0 99.9 10.0 USER1 SVC2
908 Integral Time (I) Sec 1 0 3600 10 USER1 SVC2
909 Dead Band (DBand) % 0.1 0.0 20.0 0.7 USER1 SVC2
910 Jerk Control Ratio % 0.1 0.1 99.9 10.0 USER1 SVC2
911 Max Inverter RPM rpm 10 0 9990 3600 USER1 SVC2
912 Max Inverter Frequency Hz 1 0 120 60 USER1 SVC2

VSD controls the speed of main motor according to the change of discharge pressure, so it can maintain
stable required pressure..
Control algorism uses PI control out of PID control.

① VSD Control Mode :

OFF : VSD not used.
FIX : Control in optimum load operation speed
VSD : Various speed control according to discharge pressure. [Target press. : (Operation : Load Pressure)]

② Maximum Speed : Put in the speed which limits maximum speed of motor

③ Minimum Speed : Put in the speed which limits minimum speed of motor (Put in 20% of speed range)

④ Optimum Speed : Put in optimum load speed of motor (Put in 70% of speed range)

⑤ Unloaded Speed : Speed of unload operation, In case of error in discharge press. in [Operation:Unload
Pressure]

⑥ Proportional Band (P) : Put in ‘P’ value out of PID invariable number

⑦ Integral Time (I) : Put in ‘I’ value out of PID invariable number

⑧ Dead Band (D.Band) : Dull control of speed change if the difference between discharge press. and target
press. is in dead band

⑨ Jerk Control Ratio : Limit value of motor speed variation. (Jerk Control)

⑩ Max. Inverter RPM : Put in motor speed from inverter when 100% operation.

⑪ Max. Inverter Frequency : Put in maximum operation frequency setting in inverter

.

- 37 -
UIC-DX330 Series User’s Manual Rev 2.0

16) TEST MODE

Item Description Units Step Min Max Default View Access

1000 Manual Test Mode*** - ON / OFF OFF USER1 SVC1

1001 Main Motor MAIN - ON / OFF OFF USER1 SVC1

1002 Main Motor STAR - ON / OFF OFF USER1 SVC1

1003 Main Motor DELTA - ON / OFF OFF USER1 SVC1

1004 Load SOL. Valve - ON / OFF OFF USER1 SVC1

1005 Multi Function N9 - ON / OFF OFF USER1 SVC1

1006 Multi Function N10 - ON / OFF OFF USER1 SVC1

1007 Multi Function N11 - ON / OFF OFF USER1 SVC1

1008 Multi Function N12 - ON / OFF OFF USER1 SVC1

1009 Inverter Control* mA 0.1 4.0 20.0 4.0mA USER1 SVC1

1010 Discharge Press. Retrans* mA 0.1 4.0 20.0 4.0mA USER1 SVC1

1011 Discharge Temp. Retrans.* mA 0.1 4.0 20.0 4.0mA USER1 SVC1

***
Manual test is available when [Manual Test Mode] is ON only.
*
It is only displayed in case of installing analogue output option.

① Manual Test is available when the equipment is stopped only..

② Main Motor STAR (Star Magnet) and Main Motor DELTA(Delta Magnet) cannot be turned on at the same time.

③ Manual Test Mode is automatically released after 2 minutes from the final performance of manual test.

- 38 -
UIC-DX330 Series User’s Manual Rev 2.0

17) CONFIGURE

Item Description Units Step Min Max Default View Access

1100 Master Password Setup - 1 0 9999 119 SVC3 SVC3

1101 Trip/Alarm History Delete - NO / YES NO USER1 SVC2
1102 Operation History Delete - NO / YES NO USER1 SVC2
1103 Ambient Temp. Sensor Use - ON / OFF ON USER1 SVC2
1104 Oil Reclaimer Press. Use - ON / OFF ON USER1 SVC2
1105 Oil Reclaimer Temp. Use - ON / OFF ON USER1 SVC2
1106 Discharge Press. Correction bar 0.1 -10.0 +10.0 0.0 bar USER1 SVC1
1107 Oil Press. Correction bar 0.1 -10.0 +10.0 0.0 bar USER1 SVC1
1108 Ambient Temp. Correction ℃ 0.1 -10.0 +10.0 0.0 ℃ USER1 SVC1
1109 Discharge Temp. Correction ℃ 0.1 -10.0 +10.0 0.0 ℃ USER1 SVC1
1110 Oil Temp. Correction ℃ 0.1 -10.0 +10.0 0.0 ℃ USER1 SVC1
1111 Discharge Press. Low bar 0 -10 120 0 bar USER1 SVC2
1112 Discharge Press. High bar 0 -10 120 16 bar USER1 SVC2
1113 Min. Oil Press bar 0 -10 120 0 bar USER1 SVC2
1114 Max. Oil Press bar 0 -10 120 16 bar USER1 SVC2
1115 Multi Function N9 - 1 choice out of 12 functions Cooling USER1 SVC1
1116 Multi Function N10 - 1 choice out of 12 functions OFF USER1 SVC1
1117 Multi Function N11 - 1 choice out of 12 functions OFF USER1 SVC1
1118 Multi Function N12 - 1 choice out of 12 functions OFF USER1 SVC1
※ Function list of multi function output port is supported over ‘M’ model.

Item Function Description

1 OFF No Use
2 Alarm Output Output ON : Alarm
3 Trip Output Output ON : Trip
4 Total Alarm Output ON : Trip, Alarm, Maintenance, Start Inhibit
5 Maintenance Output ON : Maintenance
6 Standby Output ON : Standby
7 Stop Output ON : Operation, Output OFF : Stop
8 Motor Run Output ON : Motor Run
9 Load Operation Output ON : Load Operation
ON : [Operation:Cooling Fan Run Temp.] >= Discharge Temp.
10 Cooling Fan
OFF : [Start Inhibit:Cooling Fan Stop Temp.] <= Discharge Temp.
ON : [Start Inhibit:Discharge Temp. Low]+ 5℃ <Discharge Temp.
11 Heater
OFF : [Start Inhibit:Discharge Temp. Low]+10℃ >Discharge Temp.
ON during [Operation:Drain Interval] as [Operation:Drain Time]
12 Drain
while motor runs

- 39 -
UIC-DX330 Series User’s Manual Rev 2.0

18) DIAGNISTIC

※ It is our initial setup value when shipped out, so you are kindly required to understand it first

and then change the value.

Item Description Units Step Min Max Default View Access

900 Self Test - NO / YES NO SVC2 SVC3

901 B1 Input - 997 SVC2 -

902 B2 Input - 280 SVC2 -

903 B3 Input - Only View 997 SVC2 -

904 B4 Input - 280 SVC2 -

905 B5 Input - 997 SVC2 -

906 B4 4mA - 85 SVC2 SVC3

907 B4 20mA - 1008 SVC2 SVC3

1 0 1023
908 B5 4mA - 255 SVC2 SVC3

909 B5 20mA - 1008 SVC2 SVC3

910 Y1 4mA - 820 SVC2 SVC3

911 Y1 20mA - 3510 SVC2 SVC3

912 Y2 4mA - 820 SVC2 SVC3

1 0 9999
913 Y2 20mA - 3510 SVC2 SVC3

914 Y3 4mA - 820 SVC2 SVC3

915 Y3 20mA - 3510 SVC2 SVC3

916 ADC F/T - 1 1 256 4 SVC2 SVC3

917 DAC F/T - 1 1 256 1 SVC2 SVC3

This product has automatic self test function and digital calibration function for digital input / output. This menu is for
improving accuracy of hardware and software of our product, when we ship it out. Therefore if you want to change any
contents of this menu, please contact us.

① Self Test: ON when shipping out

② Trip/Alarm History Delete : Use when deleting trip/alarm history
③ Operation History Delete : Use when deleting operation history
④ Bn 4mA : Analogue Input (4mA)
⑤ Bn 20mA : Analogue Input (20mA)
⑥ Yn 4mA: A variable number for changing of quantization of analogue output signal (4mA)
⑦ Yn 20mA: A variable number for changing of quantization of analogue output signal (20mA)
⑧ ADC F/T : Input filter for analogue input data (Temperature, Pressure)
⑨ DAC F/T : Output filter for analogue output data (Inverter speed control signal, Transmission Signal)

- 40 -
UIC-DX330 Series User’s Manual Rev 2.0

19) SYSTEM DATE / TIME

Date / Time is used for a point of reference to record system information such as trip/alarm history, operation
history and scheduled operation. It is inevitable when any troubles in equipment occur, so please set it up exactly.

① When you push [MENU] button once at operation screen, access code input window is displayed.
② When you push [MENU] button once again, the following window for setting date/time appears.
③ Please set up date / time by using [ENTER] and [Upward] / [Downward] button, and then return to
operation screen by pushing [CANCEL] button.
④ A day of the week is automatically set.
⑤ If “:” between hour and minute is not flickered per a second, please set it up once again.

<DATA / TIME SETUP WINDOW>

- 41 -
UIC-DX330 Series User’s Manual Rev 2.0

5. HOW TO INSTALL

1) Installed Place

Please install this controller in the following place in the same way with other general industrial electronic devices.

⊙ No variable temperature change & normal temperature

⊙ No corrosive gas
⊙ Low or high humidity
⊙ Little mechanical vibration
⊙ Little dust and smoke
⊙ Little effect of electric noise
⊙ No effect of strong magnetic filed

2) Installation Method

⊙ Installed angle should be within 15 degrees of slope from horizontal location.

⊙ Please use more than 2mm thickness of steel plate for sticking panel.
⊙ Do not set up by force.
⊙ Please fasten 4 directions of display with enclosed screws.

3) Caution for Wiring

⊙ Please use shield cable between display part and main board in order to avoid noise.
⊙ Please keep input/output signal line away more than 30cm from power line and do not put at the same lines together.
⊙ Please install fuse additionally in order to protect controller from overvoltage..
⊙ Please wire surge absorber at magnet control coil in parallel in order to improve stability of controller.
⊙ Please install noise filter in order to improve the stability of controller.
⊙ Please use AWG No. 12~28 and fasten terminal screw at 0.3~0.4N•m torque when wiring.
⊙ Please use terminal connected with controller as pen hole terminal (CE007508 standard).

- 42 -
UIC-DX330 Series User’s Manual Rev 2.0

6. WIRING DIAGRAM – DX330L

- 43 -
UIC-DX330 Series User’s Manual Rev 2.0

7. WIRING DIAGRAM – DX330M

- 44 -
UIC-DX330 Series User’s Manual Rev 2.0

8. WIRING DIAGRAM – DX330V

- 45 -