Lenovo X2

Service Manual

LENOVO

1
 Contents
1. How to assemble and disassemble LENOVO X2 ..................................................................... 3
1.1 The phone disassemble guide........................................................................................ 3
1.2 The phone assemble guide ............................................................................................ 6
2. Main board and Sub FPC layout introduction ........................................................................... 7
2.1 Main board top view ..................................................................................................... 7
2.2 Main board bottom view ............................................................................................... 8
2.3 Sub board top view ....................................................................................................... 8
2.4 Sub board bottom view ................................................................................................. 9
3. Troubleshooting Procedure ..................................................................................................... 10
3.1 No boot........................................................................................................................ 10
3.2 Touch panel have no effect.......................................................................................... 11
3.3 Charging anomaly ....................................................................................................... 12
3.4 Calling receiver sound has poor quality ...................................................................... 14
3.5 Speaker has no sound .................................................................................................. 15
3.6 LCD has no display ..................................................................................................... 16
3.7 Phone crash ................................................................................................................. 18
3.8 Key has no effect......................................................................................................... 19
3.9 Communication signal abnormality ............................................................................ 20
3.10 Calling receiver has no sound ..................................................................................... 21
3.11 Microphone has no effect ............................................................................................ 22
3.12 Display color distortion ............................................................................................... 23
3.13 Speaker tone distortion................................................................................................ 24
3.14 Speaker tone smaller ................................................................................................... 25
3.15 No charging ................................................................................................................. 26
3.16 Camera has no effect ................................................................................................... 27
3.17 Auto shutdown ............................................................................................................ 29
3.18 SIM Card has not be detected ..................................................................................... 30

2
1. How to assemble and disassemble
LENOVO X2
1.1 The phone disassemble guide

1) Take out the sim-tray

2) Disassemble the bottom of decoration

Use tweezer from the top of decoration and the battery cover gap（the back right side with the red

spot mentioned below）, released the hooks remove the decoration。

3） Disassemble the rear housing assemble

3
Note：1，The solid red dots are hooks position

2， Disassemble tools：Tweezer、Disassemble bar；in order to protect the cover from

destroy ,the disassemble bar insert just about 2mm

Using the disassemble bar to pry hooks

Released the hook1 from the lower left corner . The direction of from bottom to top to released
the hooks

4）Disassemble the main board

Disassemble the battery connector pressure Release the battery connector

sheet steel，2 screws

4
Release brackets Release the TP connector , LCD connector and
main FPC

Remove screws as the solid red dots position

5）Disassemble the sub board

Remove the SPK BOX , 3 screws red arrow board

Remove the RF cable connector from sub

Remove the sub board slowly, pay attention to protect the shrapnel and the hook ( The solid red

5
dots location)
6) Disassemble battery

If you want disassemble the battery, need to pull out the battery adhesive. The red arrow location

1.2 The phone assemble guide

Assemble and disassemble process is opposite

6
 2. Main board and Sub FPC layout
introduction
2.1 Main board top view

7
2.2 Main board bottom view

2.3 Sub board top view

8
2.4 Sub board bottom view

9
 3. Troubleshooting Procedure
3.1 No boot

Cannot boot

Check the Key FPC assembly Y the phone can power on, the
&Change the power key FPC root cause is Key FPC.

Give the 4v on the PCBA vbat pin but not

Y PCBA is bad,
power on the phone, is there any
change it.
Overload current() in the PCBA?

Connect the phone to the computer through Y Download software and

the USB line, check the computer device try power on it again.
manager if there is equipment pops up.

N
N
Check the 19.2MHz crystal is Check the crystal SMT is normal?
normal? Heat the crystal then try it again.

N
Check the battery connector Heat the battery connector
SMT is normal? then try it again.

Y
N
Check PMIC provide power supply Heat the PMIC or
to CPU and EMMC are normal? change the PMIC.

Change memory chip U1502

10
3.2 Touch panel have no effect

Touch panel no respond

Y
Change the lcd&Tp model Touch panel is not
good, change it.

Y Heat the touch panel

Check the lcd connect J1601;Is there
connector and EMI
any smt problem?
filter.
N

Check the I2C controller line

signal by the oscilloscope,

Change CPU chip

11
3.3 Charging anomaly

3.3.1 The charger is plugged in, without charging display

The charger is plugged in,

without any respond

Change the charger adapter and usb Y

Replace the charger
cable,

Measure the battery voltage, whether it Y

is less than 3V? Replace the battery

N
Y
Change the sub board Sub problem.check the sub
board

Change the main fpc and

Y
Check the main connector Main fpc problem
J1701

Check the charge ic u1302 ‘s Y

out put and in put voltage Change the U1302

12
3.3.2 Connect the phone and computer through USB line,
but not any new device was found in the computer

The USB cable is plugged

in, without any respond

Change the usb cable, Y

Replace the usb cable

Check is there any charger respond? NO

This is no charge
problem;

Y
Y
Change the sub board Sub problem.check the sub
board

Change the main fpc and

Y
Check the main connector Main fpc problem
J1701

Change the U1001

13
3.4 Calling receiver sound has poor quality

Calling sound poor

quality in receiver

Measure the receiver’s N Replace the

resistance, is the value receiver.
32ohm?

Check the contact is good between Y

receiver spring and contact point. Re OK
assemble the receiver and whether the
phone work is good.

Checks the SMT quality of bead.

Whether these parts are SMT
good? The phone is work good Y
OK
after heating these parts?

Replace the U1301

14
3.5 Speaker has no sound

Speaker has no sound

Replace the speaker, and then

does the phone work normal? Y
Whether the speaker spring is OK
normal?

Y
Replace the Sub FPC, and then Replace the
does the phone work normal? Sub FPC.

Checks the SMT quality of

these components include the
BEAD on the Sub board
Whether these parts are SMT Y
good? The phone is work good OK
after heating these parts?

Replace the codec IC

U1001

15
3.6 LCD has no display

3.6.1 Power on and no display

White or black screen &no

display, backlight is good.

The SMT of LCD connector Y

and EMI filter is not normal? OK

Replace the LCD，whether Y

the screen display is normal? OK

Checks the SMT quality of these EMI

filter. Whether these parts are SMT good?
Y
OK

Checks the U1603’s output Y Heat tU1603 or

voltage; change it

Replace the CPU U1001

16
3.6.2 LCD has no display

LCD has no
backlight

Check whether the connection

status between the LCD
module FPC connector and the
Y OK
motherboard connector is
normal, and reconnect the
connector whether the phone is
working normal.

Replace the LCD module,

Y
and make sure whether the OK
LCD has the backlight.

Check whether the LCD The backlight circuit

backlight driver(U1604) Y
is normal, and the
output voltage is exceeding LCD module is bad.
20V.

Checks the backlight

current. And found out the Y
problem;And change the smt OK
part;

17
3.7 Phone crash

Phone crash

Connecting the phone and

computer through USB line, Y
Download software
check whether some new device
was found in the computer.

Check the 19.2MHz crystal is N Heat the crystal

normal? then try it again.

Check PMIC provide power Heat the PMIC

N
supply to CPU and EMMC or change the
are normal? PMIC.

Replace the memery U1502,

whether the phone is Y
OK
working normal.

Change CPU chip U1001

18
3.8 Key has no effect

Key has no effect

Check whether the connection

status between the key FPC and the
motherboard connector is normal, Y
and reconnect the connector OK
whether the phone is working
normal.

Press the key button, make

sure whether the key signal N Replace the
line short to ground net. key FPC

Change CPU chip U1001

19
3.9 Communication signal abnormality

Communication signal
abnormality

Boot into the engineer test

mode to make sure whether Y Write the SN or
the phone has the SN or IMEI number.
IMEI number.

Check whether the

connection status between
the ANT cable and the RF
Y reconnect the
connector is normal, and
connector
reconnect the connector
whether the phone is
working normal.

Try to download Find Ythe issue part

program, whether according to the
the downloading download tool message.
is successful.

Check the modem circuit

and whether the
intermediate frequency is
good.

20
3.10 Calling receiver has no sound

Calling receiver
has no sound

Measure the resistance of N Replace the

receiver, is the value 32ohm? receiver.

Check whether the contact is good

between receiver spring and contact Y
point. Re assemble the receiver and OK
whether the phone work is good.

Checks the SMT quality of these

BEAD, Whether these parts are
SMT good? The phone is work Y
OK
good after heating these parts?

Y
Replace the codec IC
OK

21
3.11 Microphone has no effect

MIC no effect

Checks the SMT Y

quality of parts around OK
the MCI

N Y
Change the MIC ＯＫ

N
Y
Check the sub board OK
connector and main
fpc;And change the sub
board and fpc;

Replay PMIC U1301

22
3.12 Display color distortion

Display color distortion

The SMT of LCD connector Y

and EMI filter is not normal? OK

Replace the LCD，whether Y

the screen display is normal? OK

Check the U1603’s out put voltage;And Y

change the U1603 OK

Replace the CPUU1001

N

23
3.13 Speaker tone distortion

Speaker tone
distortion

Replace the speaker, and then

does the phone work normal? Y
Whether the speaker spring is OK
normal?

Y
Replace the Main FPC, and then Replace the
does the phone work normal? Main FPC.

Checks the SMT quality of

BEAD on the Sub board and.
Whether these parts are SMT
good? The phone is work good Y
after heating these parts? OK

Replace the codec IC

in sub board: U1003

24
3.14 Speaker tone smaller

Speaker tone
distortion

Replace the speaker, and then

does the phone work normal? Y
Whether the speaker spring is OK
normal?

Y
Replace the Main FPC, and then Replace the
does the phone work normal? Main FPC.

Checks the SMT quality of

BEAD on the Sub board and.
Whether these parts are SMT
good? The phone is work good Y
after heating these parts? OK

Replace the codec IC

in sub board: U1003

25
3.15 No charging

No charging

Change the charger adapter and usb Y

Replace the charger
cable,

Measure the battery voltage, whether it Y

is less than 3V? Replace the battery

N
Y
Change the sub board Sub problem.check the sub
board

Change the main fpc and

Y
Check the main connector Main fpc problem
J1701

Check the charge ic u1302 ‘s Y

out put and in put voltage Change the U1302

26
3.16 Camera has no effect

3.16.1 Main camera has no effect

No effect

Y
Check Camera module
OK
connecting is ok?

N
Y
Replace Camera
OK
module is OK?

Check the SMT quality of Camera Y

OK
connect，and reheat it is OK?

N
Check EMI filter and SMT is Reheat it
OK？

Y
N
Check the CPU SMT quality
Reheat and Replace
is OK？

27
3.16.2 Sub camera has no effect

No effect

Y
Check Camera module
OK
connecting is ok?

N
Y
Replace Camera
OK
module is OK?

Check the SMT quality of Camera Y

OK
connect，and reheat it is OK?

N
Check EMI filter and SMT is Reheat it
OK？

Y
N
Check the CPU SMT quality
Reheat and Replace
is OK？

28
3.17 Auto shutdown

Auto shutdown

Check battery temperature

detection pin, connector is good? Y Charging battery or
replace the connect.

N
Y
Using power source supply Check and found out the
power, any overload current? over current parts;

N
N
Y
Download the coder again. According to the tools
prompt, fixed bad
components
N

Check SW vision、SN、IMEI
Y Modem chip is ok?

Check charge chip is

Charging is OK? Y
ok?

Check CPU is ok?

29
3.18 SIM Card has not be detected

Sim No detected

Y Change new
Change SIM card SIM card

N
Change SIM tray. Y Change new
SIM tray

Check SN 、 IMEI have be N Rewrite SN and

written? IMEI number.

Y
Y
Check the sim card current in the main OK
board; found out open current ;

N
Y
OK
Change the U1001 and U1901

30