The document describes RC full wave triggering of an SCR. During the positive half cycle, diodes D1 and D2 are forward biased, charging capacitor C to a positive voltage through resistor R. Once charged to the gate voltage threshold, C turns on the SCR. During the negative half cycle, diodes D3 and D4 charge C, again turning on the SCR. This allows the SCR to be triggered in both half cycles with a firing angle from 0 to 180 degrees, controlling power in both half cycles. The RC time constant must exceed a calculated value for the maximum firing angle.
The document describes RC full wave triggering of an SCR. During the positive half cycle, diodes D1 and D2 are forward biased, charging capacitor C to a positive voltage through resistor R. Once charged to the gate voltage threshold, C turns on the SCR. During the negative half cycle, diodes D3 and D4 charge C, again turning on the SCR. This allows the SCR to be triggered in both half cycles with a firing angle from 0 to 180 degrees, controlling power in both half cycles. The RC time constant must exceed a calculated value for the maximum firing angle.
The document describes RC full wave triggering of an SCR. During the positive half cycle, diodes D1 and D2 are forward biased, charging capacitor C to a positive voltage through resistor R. Once charged to the gate voltage threshold, C turns on the SCR. During the negative half cycle, diodes D3 and D4 charge C, again turning on the SCR. This allows the SCR to be triggered in both half cycles with a firing angle from 0 to 180 degrees, controlling power in both half cycles. The RC time constant must exceed a calculated value for the maximum firing angle.
The document describes RC full wave triggering of an SCR. During the positive half cycle, diodes D1 and D2 are forward biased, charging capacitor C to a positive voltage through resistor R. Once charged to the gate voltage threshold, C turns on the SCR. During the negative half cycle, diodes D3 and D4 charge C, again turning on the SCR. This allows the SCR to be triggered in both half cycles with a firing angle from 0 to 180 degrees, controlling power in both half cycles. The RC time constant must exceed a calculated value for the maximum firing angle.
Video Link: https://youtu.be/fMldwqaAekM
RC Full Wave Triggering of SCR: Fig 1 shows the circuit diagram of RC Full Wave Triggering of SCR.
Fig 1: Circuit Diagram of RC Full Wave Triggering of SCR
• During positive half cycle, the supply voltage is positive and consequently D1 and D2 is forward biased. The SCR is in forward blocking mode (as anode is positive and cathode is negative). • The capacitor C charges to positive polarity through the resistor. Once the capacitor charges to the defined gate voltage, the capacitor supplies the required gate voltage. The SCR now moves from forward blocking mode to forward conduction mode and turns ON. Fig 2 shows the circuit diagram representation during positive half cycle.
Fig 2: Circuit Diagram of RC Full Wave Triggering of SCR during positive half cycle
Instagram DM: Electronics Maddy Lecture 19: RC Full Wave Triggering of SCR Video Link: https://youtu.be/fMldwqaAekM • Similarly, during negative half cycle the diodes D3 and D4 are forward biased and the capacitor charges to positive voltage. Once the capacitor charges to the defined gate voltage, the capacitor supplies the required gate voltage and the SCR is turned ON. • Fig 3 shows the circuit diagram representation during negative half cycle. The process repeats during both the half cycles. Fig 4 shows the waveforms for this circuit.
Fig 3: Circuit Diagram of RC Full Wave Triggering of SCR during negative half cycle
Instagram DM: Electronics Maddy Lecture 19: RC Full Wave Triggering of SCR Video Link: https://youtu.be/fMldwqaAekM • From the waveform it can be observed that the capacitor charges to positive voltages in both the half cycles. The capacitor voltage clamps to zero once the SCR is turned ON. • One of the major advantages with this circuit is SCR can be turned ON with a firing angle between 0 to 180 degrees. In addition, it is possible to control the SCR in both the half cycles. Hence the name RC Full Wave Triggering of SCR • The following relation holds for maximum firing angle, 0.157 RC ≥ 2𝜋𝑓 f is the supply frequency in the above equation.
