PRODUCT DATA SHEET

Sikafloor®-957 SSD
A concentrated sodium silicate densifier for improving concrete surface hardness, resistance to dirt
pick-up, and ease of polishing.

PRODUCT DESCRIPTION CHARACTERISTICS / ADVANTAGES

Sikafloor® -957 SSD is a concentrated VOC free concrete ▪ Low odor, non-yellowing water based formulation.
densifier formulated to economically harden, densify, ▪ Breathable non-film forming surface treatment.
and increase the abrasion resistance of cementitious ▪ Bonds directly to cement and aggregate silicates.
surfaces. Based on concentrated sodium silicate, it is ▪ Hardens and improves stain and scratch resistance.
diluted with water so it can deeply penetrate into ▪ Deeply penetrates, and quickly reacts.
concrete pores. It then reacts with cement, pozzolans, ▪ Shortens concrete polishing times.
and most aggregates to fill microvoids and allow ▪ UV light stable and weather resistant.
concrete to polish faster while allowing these surfaces to ▪ Cures to a non-toxic, non-flammable surface.
release moisture vapor. It is not a coating, and will not ▪ Apply by brush, roller, spray or mop.
crack, peel, or delaminate from surfaces. ▪ Accepts most water repellent surface treatments.

USES
Use as an effective concrete polishing aid, or to harden,
densify, or dustproof the cementitious surfaces of:
▪ Interior or exterior floors
▪ Stairs and walkways
▪ Ground and polished floors
▪ Below grade basements

PRODUCT INFORMATION
Chemical Base 0 VOC, Sodium Silicate, 24% solids
Packaging 5-gallon (18.9 L) Pail
Appearance / Color Slightly Cloudy
Shelf Life 24 months in original unopened container under proper storage conditions.
30 days after opening.
Storage Conditions Store in original containers at 40°F to 120°F (4°C - 49°C). DO NOT FREEZE!

Product Data Sheet

Sikafloor®-957 SSD
February 2020, Version 01.03
020815010110000032

1/3
APPLICATION INSTRUCTIONS Coverage
Coverage will depend upon method of application,
SUBSTRATE PREPARATION surface porosity, age, moisture, absorption
characteristics and the texture of the concrete. Coverage
Concrete substrate should be at least at 7days and on flat finished concrete is typically 200–400 ft2/gal
preferably 28 days old. Concrete surfaces must be dry (4.9–9.8 m2/L). Old or soft concrete will require more
and clean of all prior sealers, curing compounds oils or material. Slabs ground to expose hard non absorptive
other foreign materials that might prevent penetration. aggregates will take less material.
If used as first stage densifier or dye lock for concrete
polish work, grind to the desired aggregate exposure Equipment
ending with 80 to 200 grit tools. Use brooms or vacuums Apply Sikafloor®-957 SSD by brush, roller, sponge, mop,
to remove all grinding dust, loose concrete laitance, and or pump-spray application. Use rotary floor scrubbers
powders, or the densifier may permanently adhere them equipped with brushes or pads to assist with large jobs.
to the surface.. Always wear protective clothing and equipment proper
for the method of application.
Jobsite Test Sections
Verify and approve suitability and appearance by making Spray applicator Guidelines
jobsite test sections prior to general application. Test Pump Garden Sprayer: Use conical tip and apply with
sections must be of adequate size to be representative circular motion. Mask all areas not to be coated to
and be produced by the same workers who will apply safeguard against splashes, overspray, and runoff from
product to the larger job. Test completed systems for application. Wear all required safety equipment. Take
wet and dry slip resistance to ensure they meet care not to allow tape adhesive to interfere with
expectations. Do not proceed with products, techniques, surfaces to be treated. Surface wet with material will be
or finishing systems that do not meet required safety slippery until dry.
specifications or site owner approval. Distribute product with a pump garden sprayer to fully
saturate the surface. Surfaces should remain wet 5 to 10
minutes. Work material into the surface with a broom,
APPLICATION mop, or sponge to ensure product penetrates into
Sikafloor®-957 SSD can be used full strength or diluted substrate pores and microcracks. Take care not to create
to meet the needs of the specific project. Dilution rate, lap marks as they cannot be removed once the product
surface age, hardness, porosity, substrate moisture has dried. If too much material has been applied, and it
content, and purpose will determine the optimum is puddled after 30 minutes, dilution and removal with a
combination of dilution and coverage rate. wet vacuum is recommended.

Dilution Rates Recoat Time

Dilution rate will depend upon porosity, age and When the first application is dry to touch, a second coat
condition of the concrete: can be applied to maximize densification properties. If
used as a polishing aid, wet polishing can begin when
Partially eroded, aged, or coarsely ground concrete to be dry to touch.
polished: are recommended to dilute the product 1:1
with potable water. Dry Time
Will depend upon the selected coverage rate,
Soft, aged or lightly ground concrete to be polished: are penetration into the substrate, and weather conditions.
recommended to dilute the product 1:2 with potable At 70°F (21°C) and 50 % relative humidity with an
water. application rate of 400 sq. ft. per gallon (9.8 m2/L),
surfaces should be dry and walkable and ready for the
Hard, steel troweled, recently ground concrete in good next stage of polishing or rinsing in 1 hour.
condition are recommended to dilute the product: 1:3 If surface will not be polished further, or they will be
with potable water. sealed with coating, wash surfaces at this stage with
fresh water to remove excess densifier. when
completely dry, surface can be returned to service or
Mixing receive finish coat. If sealing waits 24 hours to allow the
Dilution should be performed in non-metallic plastic densifier to cure.
containers. Mix until uniform.

Product Data Sheet

Sikafloor®-957 SSD
February 2020, Version 01.03
020815010110000032

2/3
 LEGAL DISCLAIMER
LIMITATIONS
• KEEP CONTAINER TIGHTLY CLOSED
Sikafloor®-957 SSD is not a membrane forming curing • KEEP OUT OF REACH OF CHILDREN
compound and does not conform to ASTM C 309 • NOT FOR INTERNAL CONSUMPTION
requirements. It is not a substitute for proper curing • FOR INDUSTRIAL USE ONLY
procedures. It is not designed to provide water or oil • FOR PROFESSIONAL USE ONLY
resistance to the concrete surface without further
treatment. Prior to each use of any product of Sika Corporation, its
subsidiaries or affiliates (“SIKA”), the user must always
Do not use in combination wiht LITHOCHROME read and follow the warnings and instructions on the
chemstain classic or white surfaces will likely result. product’s most current product label, Product Data
Concrete that has carbonated at the surface may not Sheet and Safety Data Sheet which are available at
react properly with this product. if surface carbonation usa.sika.com or by calling SIKA’s Technical Service
is present it should be removed mechanically. Acid Department at 1-800-933-7452. Nothing contained in
etching is not advised. any SIKA literature or materials relieves the user of the
obligation to read and follow the warnings and
BASIS OF PRODUCT DATA instructions for each SIKA product as set forth in the
current product label, Product Data Sheet and Safety
Results may differ based upon statistical variations Data Sheet prior to use of the SIKA product.
depending upon mixing methods and equipment,
temperature, application methods, test methods, actual SIKA warrants this product for one year from date of
site conditions and curing conditions. installation to be free from manufacturing defects and
to meet the technical properties on the current Product
OTHER RESTRICTIONS Data Sheet if used as directed within the product’s shelf
life. User determines suitability of product for intended
See Legal Disclaimer. use and assumes all risks. User’s and/or buyer’s sole
remedy shall be limited to the purchase price or
ENVIRONMENTAL, HEALTH AND SAFETY replacement of this product exclusive of any labor costs.
NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL
APPLY INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL
THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES.
SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS
PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT
OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD
BY OTHERS.

Sale of SIKA products are subject to the Terms and

Conditions of Sale which are available at
https://usa.sika.com/en/group/SikaCorp/termsandconditions.html
or by calling 1-800-933-7452.

Sika Corporation Sika Mexicana S.A. de C.V.

201 Polito Avenue Carretera Libre Celaya Km. 8.5
Lyndhurst, NJ 07071 Fracc. Industrial Balvanera
Phone: +1-800-933-7452 Corregidora, Queretaro
Fax: +1-201-933-6225 C.P. 76920
usa.sika.com Phone: 52 442 2385800
Fax: 52 442 2250537

Sikafloor-957SSD-en-US-(02-2020)-1-3.pdf

Product Data Sheet

Sikafloor®-957 SSD
February 2020, Version 01.03
020815010110000032

3/3