0% found this document useful (0 votes)
29 views

Week 1 Assignment Solution

The document contains 15 multiple choice questions about sensors and IoT networking protocols. It tests knowledge about topics like sensor resolution, operating voltages of sensors, types of actuators, wireless communication standards like Zigbee and 6LoWPAN, and IoT networking protocols including CoAP, MQTT, AMQP and DDS.

Uploaded by

DNA EditzZz
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
29 views

Week 1 Assignment Solution

The document contains 15 multiple choice questions about sensors and IoT networking protocols. It tests knowledge about topics like sensor resolution, operating voltages of sensors, types of actuators, wireless communication standards like Zigbee and 6LoWPAN, and IoT networking protocols including CoAP, MQTT, AMQP and DDS.

Uploaded by

DNA EditzZz
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

1. In the context of static characteristics of a sensor, which of the following signifies resolution?

a. It provides the smallest change in the input that a sensor is capable of Sensing
b. It is the difference between the standard value and the value produced by Sensor
c. It is the deviation of sensor value curve from a particular straight line
d. It represents the correctness of the output compared to a superior system

Answer: (a)

Justification: Please refer to Slide 9 of Lecture 1 of Week 1

2. What is the general operating voltage range of commercial sensors which are available for
circuit enthusiasts and hobbyists?

a. 3.3 to 5 V
b. 4.5 to 8 V
c. 3.5 to 12 V
d. 3.3 to 8 V

Answer: (a)
EL
Justification: Please refer to page 185 (Section 8.2.6 – Operating Voltage) of the book
“Introduction to Industrial Internet of Things and Industry 4.0 by Misra et. al.”.
PT

3. Which of the following actuators produce linear displacement?


N

a. Manual Linear Actuator


b. Fluid Power Linear Actuator
c. Electric Linear Actuator
d. All of the above

Answer: (d)

Justification: Please refer to Slide 24, 26, 29 of Lecture 1 of Week 1

4. IEEE 802.15.4 uses ____________ protocol for data transmission.

a. ALOHA
b. CSMA-CA
c. CSMA-CD
d. None of the above

Answer: (b)
Justification: Please refer to Slide 6 of Lecture 2 of Week 1

5. Which of the following is not an operating frequency of ZigBee?

a. 950 KHz
b. 868 MHz
c. 902-928 MHz
d. 2.4 GHz

Answer: (a)

Justification: Please refer to Slide 11 of Lecture 2 of Week 1

6. What is/are the role(s) of adaptation layer in 6LoWPAN?

a. Packet fragmentation & packet reassembly


b. Compression of header
c. Routing of data link layer
d. All the above

Answer: (d)
EL
Justification: Please refer to Slide 18 of Lecture 2 of Week 1
PT

7. Maximum payload allowed in wireless HART is ______ bytes?


N

a. 63
b. 127
c. 255
d. 512

Answer: (b)

Justification: Please refer to Slide 25 of Lecture 2 of Week 1

8. Radio dead-spots can be bypassed using a process called _____.

a. Healing
b. Multi-hop
c. Adaptation
d. Reduction

Answer: (a)
Justification: Please refer to Slide 5 of Lecture 3 of Week 1

9. In which application domain does ISA 100.11a is primarily used?

a. Home/Office Automation
b. System for Smart Security and Surveillance
c. Systems for Smart Energy Management
d. Automation in large scale complex industries

Answer: (d)

Justification: Please refer to Slide 10 of Lecture 3 of Week 1

10. Which wireless communication technology is based on Ad-hoc Piconets?

a. Wireless HART
b. ZigBee
c. Bluetooth
d. Z-Wave

Answer: (c)
EL
Justification: Please refer to Slide 12 of Lecture 3 of Week 1
PT

11. What does the abbreviation, NFC, stands for?


N

a. New Frequency communication


b. Near Frequency communication
c. Near Field communication
d. Non-Friendly communication

Answer: (c)

Justification: Please refer to Slide 20 of Lecture 3 of Week 1

12. Which of the following work groups extend the integration of the IoT devices from network to
service level.

a. 6LoWPAN
b. ROLL
c. CoRE
d. None of the above

Answer: (c)
Justification: Please refer to Slide 7 of Lecture 4 of Week 1

13. QoS policies for IoT Network includes _______.

a. Resource utilization
b. Data timeliness
c. Data availability
d. All of the above

Answer: (d)

Justification: Please refer to Slide 12 of Lecture 4 of Week 1

14. Which IoT networking protocol supports caching capabilities to improve the response time
and reduce bandwidth consumption?

a. MQTT
b. XMPP
c. CoAP
d. AMQP
EL
Answer: (c)

Justification: Please refer to Slide 12 of Lecture 5 of Week 1


PT

15. Which IoT networking protocol is used in the Military?


N

a. DDS RTPS
b. IEEE 1888
c. AMCP
d. CoAP

Answer: (a)

Justification: Please refer to Slides 23 of Lecture 5 of Week 1

You might also like