Scribd
Upload
370 views1 page

Test Plan 3717

This document provides calibration data for an injection assortment used on a specific engine model. It includes: 1) Information on the direction of rotation, beginning of delivery, injection order, tolerance zones, and angular divisions for the injection assortment. 2) Specifications for the injection nozzles, injectors, opening pressure, high pressure pipes, overpressure valve, and temperature of the testing liquid. 3) A table with adjustment operations listing revolutions/minutes, number of strokes, delivery quantity range, difference allowed, and notices for items like fuel delivery maximum, beginning of stopping, idle-speed delivery stop check, and operation number 1 check and stop.

Uploaded by

LIONN ONESOLUTION
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
370 views1 page

Test Plan 3717

This document provides calibration data for an injection assortment used on a specific engine model. It includes: 1) Information on the direction of rotation, beginning of delivery, injection order, tolerance zones, and angular divisions for the injection assortment. 2) Specifications for the injection nozzles, injectors, opening pressure, high pressure pipes, overpressure valve, and temperature of the testing liquid. 3) A table with adjustment operations listing revolutions/minutes, number of strokes, delivery quantity range, difference allowed, and notices for items like fuel delivery maximum, beginning of stopping, idle-speed delivery stop check, and operation number 1 check and stop.

Uploaded by

LIONN ONESOLUTION
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

CALIBRATION DATA CHART 6570

INJECTION ASSORTMENT PP6M10P1i - 3717


FOR ENGINE: F6L914
The mentioned values are for MOTORPAL Test Equipment only 29/05/2023
A: 1. Direction of rotation RIGHT Adjusting pictures: S507
2. Beginning of delivery 5,0 +- 0,05 mm od/from DMP
3. Injection order 1-5-3-6-2-4 The locking device set at TBD position of 6. element. Testing liquid
ISO 4113 (Shell S.9365).
4. Tolerance zone +-30'
5. Angular division 0°-60°-120°-180°-240°-300°

B: 1. Injection nozzles 0,6 mm


2. Injectors 1688901101
3. Opening pressure 20,7 MPa
4. High pressure pipes 6x2x600 mm
5. Overpressure valve 160-200 kPa
6. Temp. of test. liquid ISO 4113 (Shell) 40 °C

C: Adjusting operation Revolutions No. of Delivery Q Difference Notice Angle


/ min strokes (ccm) (ccm)
1 Fuel delivery max. 1075 200 17,8-18,4 0,8 1a*,1b* x=3,0 mm
2 Beginning of STOPPING 1095-1105 2*
3 STOP max. 1190 0 3*
4 Anti-corrector setting 800 200 15,4-16,0 0,8 5*
5 Aut.START del.end 530-560 6*
6 Corrector setting 750 200 17,4-18,0 1,0 4*
7 Aut.START del.end 500-530 6* kontrol.
8 Fuel delivery checking 600 200 max. 16,6 1,0
9 Start fuel delivery 100 100 8,8-10,2 1,2 8*
10 Idle-speed del.STOP check. 350 300 6,3-8,4 1,8 7*,7a*
11 Fuel delivery checking 250 200 min. 12,0
12 Idle-speed STOP max. 450 0
13 Op.No.1 and STOP checking 1075 200 17,8-18,4 0,8 1c*

You might also like