1712-1U-01G(09-18).

fm 1 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
09–18 LIGHTING SYSTEMS
LOCATION INDEX . . . . . . . . . . . . . . . . . 09–18–2 BACK-UP LIGHT SWITCH
FRONT COMBINATION LIGHT REMOVAL/INSTALLATION . . . . . . . . . . 09–18–15
REMOVAL/INSTALLATION . . . . . . . . . 09–18–5 BACK-UP LIGHT SWITCH INSPECTION 09–18–15
HEADLIGHT ADJUSTMENT. . . . . . . . . . 09–18–5 FLASHER CONTROL MODULE
HEADLIGHT BULB REMOVAL/INSTALLATION . . . . . . . . . . 09–18–16
REMOVAL/INSTALLATION . . . . . . . . . 09–18–6 FLASHER CONTROL MODULE
Headlight Bulb Removal Note INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–18–16
(4SD and 5HB Low-beam) . . . . . . . . . 09–18–6 Terminal Voltage List (Reference) . . . . 09–18–16
Headlight Bulb Removal Note DAYTIME RUNNING LIGHT (DRL)
(5HB High-beam) . . . . . . . . . . . . . . . . 09–18–6 SYSTEM WIRING DIAGRAM . . . . . . . . . 09–18–17
Cover Installation Note. . . . . . . . . . . . . 09–18–6 DRL CONTROL MODULE
FRONT TURN LIGHT/PARKING LIGHT BULB REMOVAL/INSTALLATION (CANADA) 09–18–18
REMOVAL/INSTALLATION . . . . . . . . . 09–18–7 DRL CONTROL MODULE INSPECTION
FRONT SIDE MARKER LIGHT (CANADA) . . . . . . . . . . . . . . . . . . . . . . . 09–18–18
REMOVAL/INSTALLATION . . . . . . . . . 09–18–7 Terminal Voltage List (Reference) . . . . 09–18–18
4SD . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–18–7 INTERIOR AND MAP LIGHT
5HB . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–18–7 REMOVAL/INSTALLATION . . . . . . . . . . 09–18–20
FRONT FOG LIGHT Lens Removal Note. . . . . . . . . . . . . . . . 09–18–20
REMOVAL/INSTALLATION . . . . . . . . . 09–18–8 INTERIOR AND MAP LIGHT
4SD . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–18–8 INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–18–20
5HB . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–18–8 MAP LIGHT REMOVAL/INSTALLATION 09–18–21
FRONT FOG LIGHT ADJUSTMENT. . . . 09–18–9 Lens Removal Note. . . . . . . . . . . . . . . . 09–18–21
REAR COMBINATION LIGHT MAP LIGHT INSPECTION . . . . . . . . . . . . 09–18–21
REMOVAL/INSTALLATION . . . . . . . . . 09–18–10 INTERIOR LIGHT
Socket Installation Note . . . . . . . . . . . . 09–18–10 REMOVAL/INSTALLATION . . . . . . . . . . 09–18–22
HIGH-MOUNT BRAKE LIGHT Lens Removal Note. . . . . . . . . . . . . . . . 09–18–22
09–18
REMOVAL/INSTALLATION . . . . . . . . . 09–18–11 INTERIOR LIGHT INSPECTION . . . . . . . 09–18–22
In-Vehicle Type . . . . . . . . . . . . . . . . . . 09–18–11 TRUNK COMPARTMENT LIGHT BULB
Rear Spoiler Type . . . . . . . . . . . . . . . . 09–18–11 REMOVAL/INSTALLATION . . . . . . . . . . 09–18–23
LICENSE PLATE LIGHT TRUNK COMPARTMENT LIGHT SWITCH
REMOVAL/INSTALLATION . . . . . . . . . 09–18–12 INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–18–23
License Plate Light Removal Note . . . . 09–18–12 CARGO COMPARTMENT LIGHT
COMBINATION SWITCH REMOVAL/INSTALLATION . . . . . . . . . . 09–18–23
REMOVAL/INSTALLATION . . . . . . . . . 09–18–12 CARGO COMPARTMENT LIGHT
COMBINATION SWITCH DISASSEMBLY/ INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–18–24
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . 09–18–13 CARGO COMPARTMENT LIGHT SWITCH
LIGHT SWITCH INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–18–24
REMOVAL/INSTALLATION . . . . . . . . . 09–18–13 IGNITION KEY ILLUMINATION BULB
LIGHT SWITCH INSPECTION . . . . . . . . 09–18–13 REMOVAL/INSTALLATION . . . . . . . . . . 09–18–24
Headlight switch. . . . . . . . . . . . . . . . . . 09–18–13 DOOR SWITCH
Turn switch. . . . . . . . . . . . . . . . . . . . . . 09–18–14 REMOVAL/INSTALLATION . . . . . . . . . . 09–18–24
FRONT FOG LIGHT SWITCH Front . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–18–24
REMOVAL/INSTALLATION . . . . . . . . . 09–18–14 Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–18–25
FRONT FOG LIGHT SWITCH DOOR SWITCH INSPECTION . . . . . . . . . 09–18–25
INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–18–14 PANEL LIGHT CONTROL SWITCH
HAZARD WARNING SWITCH REMOVAL/INSTALLATION . . . . . . . . . . 09–18–25
REMOVAL/INSTALLATION . . . . . . . . . 09–18–14 Panel Light Control Switch
HAZARD WARNING SWITCH Removal Note . . . . . . . . . . . . . . . . . . 09–18–25
INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–18–15 PANEL LIGHT CONTROL SWITCH
INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–18–26
Terminal Voltage List (Reference) . . . . 09–18–26

End of Toc

09–18–1
1712-1U-01G(09-18).fm 2 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
LOCATION INDEX
A3U091801051W01

A3U0918W108

1 Front combination light 5 Interior and map light

(See 09–18–5 FRONT COMBINATION LIGHT (See 09–18–20 INTERIOR AND MAP LIGHT
REMOVAL/INSTALLATION) REMOVAL/INSTALLATION)
(See 09–18–5 HEADLIGHT ADJUSTMENT) (See 09–18–20 INTERIOR AND MAP LIGHT
(See 09–18–6 HEADLIGHT BULB REMOVAL/ INSPECTION)
INSTALLATION) 6 Map light
(See 09–18–7 FRONT TURN LIGHT/PARKING (See 09–18–21 MAP LIGHT REMOVAL/
LIGHT BULB REMOVAL/INSTALLATION) INSTALLATION)
(See 09–18–7 4SD) (See 09–18–21 MAP LIGHT INSPECTION)
2 Front side marker light (5HB) 7 Interior light
(See 09–18–7 5HB) (See 09–18–22 INTERIOR LIGHT REMOVAL/
3 Front fog light INSTALLATION)
(See 09–18–9 FRONT FOG LIGHT ADJUSTMENT) (See 09–18–22 INTERIOR LIGHT INSPECTION)
(See 09–18–8 FRONT FOG LIGHT REMOVAL/ 8 Door switch
INSTALLATION) (See 09–18–24 DOOR SWITCH REMOVAL/
4 Back-up light switch INSTALLATION)
(See 09–18–15 BACK-UP LIGHT SWITCH (See 09–18–25 DOOR SWITCH INSPECTION)
REMOVAL/INSTALLATION)
(See 09–18–15 BACK-UP LIGHT SWITCH
INSPECTION)

09–18–2
1712-1U-01G(09-18).fm 3 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS

09–18

A3U0918W104

1 Rear combination light 5 Trunk compartment light switch

(See 09–18–10 REAR COMBINATION LIGHT (See 09–18–23 TRUNK COMPARTMENT LIGHT
REMOVAL/INSTALLATION) SWITCH INSPECTION)
2 High-mount brake light 6 Cargo compartment light
(See 09–18–11 HIGH-MOUNT BRAKE LIGHT (See 09–18–23 CARGO COMPARTMENT LIGHT
REMOVAL/INSTALLATION) REMOVAL/INSTALLATION)
3 License plate light (See 09–18–24 CARGO COMPARTMENT LIGHT
(See 09–18–12 LICENSE PLATE LIGHT INSPECTION)
REMOVAL/INSTALLATION) 7 Cargo compartment light switch
4 Trunk compartment light bulb (See 09–18–24 CARGO COMPARTMENT LIGHT
(See 09–18–23 TRUNK COMPARTMENT LIGHT SWITCH INSPECTION)
BULB REMOVAL/INSTALLATION)

09–18–3
1712-1U-01G(09-18).fm 4 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS

Z3U0918W013

1 Combination switch 5 Flasher control module

(See 09–18–12 COMBINATION SWITCH (See 09–18–16 FLASHER CONTROL MODULE
REMOVAL/INSTALLATION) REMOVAL/INSTALLATION)
(See 09–18–13 COMBINATION SWITCH (See 09–18–16 FLASHER CONTROL MODULE
DISASSEMBLY/ASSEMBLY) INSPECTION)
2 Light switch 6 DRL control module
(See 09–18–13 LIGHT SWITCH REMOVAL/ (See 09–18–18 DRL CONTROL MODULE
INSTALLATION) REMOVAL/INSTALLATION (CANADA))
(See 09–18–13 LIGHT SWITCH INSPECTION) (See 09–18–18 DRL CONTROL MODULE
3 Front fog light switch INSPECTION (CANADA))
(See 09–18–14 FRONT FOG LIGHT SWITCH 7 Panel light control switch
REMOVAL/INSTALLATION) (See 09–18–25 PANEL LIGHT CONTROL SWITCH
(See 09–18–14 FRONT FOG LIGHT SWITCH REMOVAL/INSTALLATION)
INSPECTION) (See 09–18–26 PANEL LIGHT CONTROL SWITCH
4 Hazard warning switch INSPECTION)
(See 09–18–14 HAZARD WARNING SWITCH
REMOVAL/INSTALLATION)
(See 09–18–15 HAZARD WARNING SWITCH
INSPECTION)

End Of Sie

09–18–4
1712-1U-01G(09-18).fm 5 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
FRONT COMBINATION LIGHT REMOVAL/INSTALLATION
A3U091851060W01
1. Disconnect the negative battery cable.
2. Remove the front bumper. (See 09–10–5 FRONT BUMPER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
1 Connector
2 Bolt
3 Front combination light

4. Install in the reverse order of removal.

5. Adjust the headlight aiming. (See 09–18–5
HEADLIGHT ADJUSTMENT.)
End Of Sie

Y3J8112W111

HEADLIGHT ADJUSTMENT
A3U091851030W01
1. Adjust the tire air pressure to the specification.
2. Position the unloaded vehicle on a flat, level surface.
3. Seat one person in the driver's seat.
4. Position the vehicle straight ahead and perpendicular to a wall.
5. Set the headlights 3 m {10 ft} from the wall.
6. While adjusting one headlight, disconnect the
connector of the other.
7. Start the engine to charge the battery.
8. Turn on the low-beam headlight.

09–18

Z3U0918W006

9. Adjust the headlights by turning the adjusting

screws as shown in the figure. Loosen the screws
first, then tighten them.

Note
• If the adjusting screws are tightened first,
then loosened, they will continue to loosen
when the vehicle is in motion and may cause
the headlights to become misaligned.

End Of Sie

Z3U0918W001

09–18–5
1712-1U-01G(09-18).fm 6 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
HEADLIGHT BULB REMOVAL/INSTALLATION
A3U091851030W02
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.

Caution
• A halogen bulb generates extremely high heat when it is used. If the surface of the bulb is dirty,
excessive heat will build up and the light's life will be shortened. When replacing the bulb, hold the
metal flange, not the glass.

3. Install in the reverse order of removal.

A3U0918W101

1 Connector 3 Headlight bulb

2 Cover (See 09–18–6 Headlight Bulb Removal Note (4SD
(See 09–18–6 Cover Installation Note) and 5HB Low-beam))
(See 09–18–6 Headlight Bulb Removal Note (5HB
High-beam))

Headlight Bulb Removal Note (4SD and 5HB Low-beam)

1. Release the bulb seating wire to remove the headlight bulb.

Headlight Bulb Removal Note (5HB High-beam)

1. Turn the bulb to remove the headlight bulb.

Cover Installation Note

1. Make sure the cover is seated properly to prevent the moisture from getting into the headlight housing.
End Of Sie

09–18–6
1712-1U-01G(09-18).fm 7 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
FRONT TURN LIGHT/PARKING LIGHT BULB REMOVAL/INSTALLATION
A3U091851050W01
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
1 Connector
2 Socket
3 Front turn light/parking light bulb

3. Install in the reverse order of removal.

End Of Sie

Y3J8112W107

FRONT SIDE MARKER LIGHT REMOVAL/INSTALLATION

A3U091851120W01
4SD
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
1 Socket
2 Connector
3 Front side marker light bulb

3. Install in the reverse order of removal.

09–18

Z3U0918W002

5HB
1. Disconnect the negative battery cable.
2. Remove the bolts and fasteners, and bend the splash shield down.
3. Remove in the order indicated in the table.
1 Front side marker light
(See 09–18–7 Front side marker light removal note)
2 Connector
3 Socket
4 Front side marker light bulb

4. Install in the reverse order of removal.

A3U0918W112

Front side marker light removal note

1. Pull out the rear end of the front side marker light while pressing the hook.
End Of Sie

09–18–7
1712-1U-01G(09-18).fm 8 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
FRONT FOG LIGHT REMOVAL/INSTALLATION
A3U091851680W01
4SD
Caution
• A halogen bulb generates extremely high heat when it is used. If the surface of the bulb is dirty,
excessive heat will build up and the bulb’s life will be shortened. When replacing the bulb, hold the
metal flange, not the glass.
1. Disconnect the negative battery cable.
2. Turn over the mud guard.
3. Remove in the order indicated in the table.
1 Bolt
2 Connector
3 Front fog light
4 Screw
5 Cover
6 Bulb pressing wire
7 Front fog light bulb

4. Install in the reverse order of removal.

5. Adjust the front fog light aiming. (See 09–18–9
FRONT FOG LIGHT ADJUSTMENT.)

Z3U0918W014

5HB
Caution
• A halogen bulb generates extremely high heat when it is used. If the surface of the bulb is dirty,
excessive heat will build up and the bulb’s life will be shortened. When replacing the bulb, hold the
metal flange, not the glass.
1. Disconnect the negative battery cable.
2. Remove the front bumper. (See 09–10–5 FRONT BUMPER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
1 Nut
2 Connector
3 Front fog light
4 Screw
5 Front fog light unit
6 Connector
7 Bulb pressing wire
8 Front fog light bulb

4. Install in the reverse order of removal.

5. Adjust the front fog light aiming. (See 09–18–9
FRONT FOG LIGHT ADJUSTMENT.)
End Of Sie

A3U0918W110

09–18–8
1712-1U-01G(09-18).fm 9 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
FRONT FOG LIGHT ADJUSTMENT
A3U091851680W02
1. Adjust the tire air pressure to the specification.
2. Position the unloaded vehicle on a flat, level surface.
3. Seat one person in the driver’s seat.
4. Position the vehicle 3 m {10 ft} in front of a white
screen.
5. While adjusting one fog light, mask the other.
6. Start the engine to charge the battery.
7. Turn the front fog light on.
8. Peel off the mud guard.
9. Loosen the screw or bolts for the aim adjustment.
10. Move the front fog light in the direction of the
arrows indicated in the figure and adjust the
center of the front fog light to the position.

Z3U0918W006

09–18

A3U0918W111

11. Tighten the front fog light adjusting screw or bolts.

End Of Sie

09–18–9
1712-1U-01G(09-18).fm 10 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
REAR COMBINATION LIGHT REMOVAL/INSTALLATION
A3U091851150W01
1. Disconnect the negative battery cable.
2. Remove the trunk side trim. (See 09–17–15 TRUNK SIDE TRIM REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
1 Connector
2 Nut
3 Rear combination light
4 Socket
(See 09–18–10 Socket Installation Note)
5 Brake light/taillight bulb
6 Rear turn light bulb
7 Back-up light bulb
8 Rear side marker light bulb (4SD)
9 Taillight bulb (4SD)

4. Install in the reverse order of removal.

A3U0918W107

Socket Installation Note

1. Hook the harness as shown in the figure.
End Of Sie

A3U0918W106

09–18–10
1712-1U-01G(09-18).fm 11 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
HIGH-MOUNT BRAKE LIGHT REMOVAL/INSTALLATION
A3U091851580W01
In-Vehicle Type
1. Disconnect the negative battery cable.
2. Remove the rear package trim. (See 09–17–12 REAR PACKAGE TRIM REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
1 High-mount brake light
2 Lens
3 Socket
4 High-mount brake light bulb

4. Install in the reverse order of removal.

Y3U918WAM
09–18

Rear Spoiler Type

1. Disconnect the negative battery cable.
2. Remove the rear spoiler. (See 09–16–8 REAR SPOILER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
1 Screw
2 High-mount brake light
(See 09–18–12 High-mount brake light removal
note (4SD))

4. Install in the reverse order of removal.

A3U0918W102

09–18–11
1712-1U-01G(09-18).fm 12 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
High-mount brake light removal note (4SD)
1. Tie a string to the end of the connector of the
high-mount brake light beforehand so that the
connector can be passed easily through the rear
spoiler during installation.
End Of Sie

Y3U918WAJ

LICENSE PLATE LIGHT REMOVAL/INSTALLATION

A3U091851270W01
1. Disconnect the negative battery cable.
2. Remove the rear finisher. (See 09–16–3 REAR FINISHER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
1 License plate light
(See 09–18–12 License Plate Light Removal Note)
2 Connector
3 Socket
4 License plate light bulb

4. Install in the reverse order of removal.

X3U918WA7

License Plate Light Removal Note

1. Slide the license plate light to the arrow mark and
remove it.
End Of Sie

X3U918WA8

COMBINATION SWITCH REMOVAL/INSTALLATION

A3U091866120W01
1. Disconnect the negative battery cable.
2. Remove the driver-side air bag module. (See 08–10–5 DRIVER-SIDE AIR BAG MODULE REMOVAL/
INSTALLATION.)
3. Remove the steering wheel. (See 06–12–6 STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)
4. Remove the column cover. (See 09–17–5 COLUMN COVER REMOVAL/INSTALLATION.)
5. Remove the clock spring. (See 08–10–9 CLOCK SPRING REMOVAL/INSTALLATION.)
6. Remove in the order indicated in the table.
1 Connector
2 Screw
3 Combination switch

7. Install in the reverse order of removal.

End Of Sie

X3U918WA9

09–18–12
1712-1U-01G(09-18).fm 13 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
COMBINATION SWITCH DISASSEMBLY/ASSEMBLY
A3U091866120W02
1. Disassemble in the order indicated in the table.
1 Screw
2 Wiper lever
3 Light lever
4 Body

2. Assemble in the reverse order of disassembly.

End Of Sie

Z3U0918W003

LIGHT SWITCH REMOVAL/INSTALLATION

A3U091866121W01
1. Disconnect the negative battery cable.
2. Remove the column cover. (See 09–17–5 COLUMN COVER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
1 Connector
2 Screw
3 Light lever
09–18
4. Install in the reverse order of removal.
End Of Sie

X3U918WAB

LIGHT SWITCH INSPECTION

A3U091866121W02
Headlight switch
1. Remove the light switch. (See 09–18–13 LIGHT SWITCH REMOVAL/INSTALLATION.)
2. Inspect for continuity between the light switch
terminals using an ohmmeter.
• If not as specified, replace the light switch.

Y3U918WAN

Y3U918WA0

09–18–13
1712-1U-01G(09-18).fm 14 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
Turn switch
1. Remove the light switch. (See 09–18–13 LIGHT SWITCH REMOVAL/INSTALLATION.)
2. Inspect for continuity between the light switch
terminals using an ohmmeter.
• If not as specified, replace the light switch.

Y3U918WA1
X3U918WBG

End Of Sie
FRONT FOG LIGHT SWITCH REMOVAL/INSTALLATION
A3U091866402W01
1. Disconnect the negative battery cable.
2. Remove the left side side panel from the dashboard.
3. Compress the tabs of the front fog light switch
and pull the switch out of the dashboard.
4. Disconnect the connector to remove the front fog
light switch.
5. Install in the reverse order of removal.
End Of Sie

Z3U0918W009

FRONT FOG LIGHT SWITCH INSPECTION

A3U091866402W02
1. Remove the front fog light switch. (See 09–18–14 FRONT FOG LIGHT SWITCH REMOVAL/INSTALLATION.)
2. Inspect for continuity between the front fog light
switch terminals using an ohmmeter.
• If not as specified, replace the front fog light
switch.

Z3U0918W008

End Of Sie Z3U0918W007

HAZARD WARNING SWITCH REMOVAL/INSTALLATION

A3U091866401W01
1. Disconnect the negative battery cable.
2. Remove the center panel. (See 09–17–4 CENTER PANEL REMOVAL/INSTALLATION.)
3. Grasp the tabs of the hazard warning switch and
pull it forward to remove it.
4. Install in the reverse order of removal.
End Of Sie

Y3U918WAP

09–18–14
1712-1U-01G(09-18).fm 15 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
HAZARD WARNING SWITCH INSPECTION
A3U091866401W02
1. Remove the hazard warning switch. (See 09–18–14 HAZARD WARNING SWITCH REMOVAL/
INSTALLATION.)
2. Inspect for continuity between the hazard warning
switch terminals using an ohmmeter.
• If not as specified, replace the hazard warning
switch.

X3U918WBH

End Of Sie

Y3U918WA2

BACK-UP LIGHT SWITCH REMOVAL/INSTALLATION 09–18

A3U091817640W01
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
1 Connector
2 Back-up light switch

3. Install in the reverse order of removal.

End Of Sie

X3U918WAG

BACK-UP LIGHT SWITCH INSPECTION

A3U091817640W02
1. Disconnect the back-up light switch connector.
2. Inspect for continuity between the back-up light
switch terminals using an ohmmeter.
• If not as specified, replace the back-up light
switch.

X3U918WBJ
Y3U918WA3
End Of Sie

09–18–15
1712-1U-01G(09-18).fm 16 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
FLASHER CONTROL MODULE REMOVAL/INSTALLATION
A3U091866830W01
Note
• Because the lock section of the control module is damaged easily, do not remove the control module from
the bracket unless replacement is necessary. Always perform an inspection of the flasher control module
before removal.
1. Disconnect the negative battery cable.
2. Remove the bracket.
3. Disconnect the flasher control module connector.
4. Remove the flasher control module by prying the
lock section of the upper part with a flathead
screwdriver.
5. Install in the reverse order of removal.
End Of Sie

X3U918WAJ

FLASHER CONTROL MODULE INSPECTION

A3U091866830W02
1. Remove the bracket and pull it toward you.
2. Measure the voltage at the flasher control module terminals as indicated below.
3. Disconnect the flasher control module connector before inspecting for continuity at terminal F.
• If not as specified, inspect the parts listed under “Action."
• If the parts and wiring harnesses are okay but the system still does not work properly, replace the flasher
control module.
Terminal Voltage List (Reference)

ZLU918WA6

Connected Voltage (V)/

Terminal Signal Test condition Action
to Continuity
HAZARD 15 • Inspect HAZARD 15 A fuse
A Power supply Under any condition B+
A fuse • Inspect related harness
B — — — — —
Turn signal light (LH) flashes.
Alternates below
Turn signal Turn signal Hazard warning switch at on 1.0 and B+ • Inspect turn signal light (LH)
D
flasher (LH) light (LH) position. • Inspect related harness
Other Below 1.0
Flasher control Constant: inspect for
F GND Yes • Inspect GND
module ground continuity to ground.
Turn signal light (RH) flashes.
Alternates below
Turn signal Turn signal Hazard warning switch at on 1.0 and B+ • Inspect turn signal light (RH)
G
flasher (RH) light (RH) position. • Inspect related harness
Other Below 1.0
Hazard warning switch at on • Inspect hazard warning switch
Below 1.0
Hazard position. (See 09–18–15 HAZARD
Hazard
H warning WARNING SWITCH
warning on Hazard warning switch at off
switch B+ INSPECTION)
position. • Inspect related harness
Ignition switch is at ON and • Inspect light switch
B+
Combination turn switch (RH) on. (See 09–18–13 LIGHT
Turn switch on/
I switch (light SWITCH INSPECTION)
off (RH)
switch) Other Below 1.0 • Inspect TURN 10 A fuse
• Inspect related harness
Ignition switch is at ON and • Inspect light switch
B+
Combination turn switch (LH) on. (See 09–18–13 LIGHT
Turn switch on/
J switch (light SWITCH INSPECTION)
off (LH)
switch) Other Below 1.0 • Inspect TURN 10 A fuse
• Inspect related harness

09–18–16
1712-1U-01G(09-18).fm 17 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
End Of Sie

DAYTIME RUNNING LIGHT (DRL) SYSTEM WIRING DIAGRAM

A3U091867750W01

09–18

A3U0918W105

End Of Sie

09–18–17
1712-1U-01G(09-18).fm 18 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
DRL CONTROL MODULE REMOVAL/INSTALLATION (CANADA)
A3U091867750W02

Note
• Because the lock section of the control module is damaged easily, do not remove the control module from
the bracket unless replacement is necessary. Always perform an inspection of the DRL control module
before removal.

1. Remove the negative battery cable.

2. Remove the bracket.
3. Disconnect the DRL control module connector.
4. Remove the DRL control module by prying the
lock section of the side part with a flathead
screwdriver.
5. Install in the reverse order of removal.
End Of Sie

X3U918WAL

DRL CONTROL MODULE INSPECTION (CANADA)

A3U091867750W03
1. Remove the bracket and pull it toward you.
2. Measure the voltage at the DRL control module terminals as indicated below.
3. Disconnect the DRL control module connector before inspecting for continuity at terminal 1E.
• If not as specified, inspect the parts listed under “Action.”
• If the parts and wiring harnesses are okay but the system still does not work properly, replace the DRL
control module.

Terminal Voltage List (Reference)

Y3U918WA7

Voltage (V)/
Terminal Signal Connected to Test condition Action
Continuity
Dimmer 4SD B+
Headlight switch at high
switch at beam position 5HB Below 1.5 • Inspect HEAD R 15 A
RH headlight headlight
RH headlight fuse
1A operation (low Dimmer switch at low
(low beam) position Below 1.5 • Inspect RH headlight
beam) beam position
• Inspect related harness
Headlight switch at OFF or TNS
Below 1.5
position
Ignition switch at ON position B+ • Inspect METER 10 A
METER 10 A
1B IG1 Ignition switch at LOCK or ACC fuse
fuse Below 1.0
position • Inspect related harness
Dimmer 4SD B+
Headlight switch at high
switch at beam position 5HB Below 1.5 • Inspect HEAD L 15 A
LH headlight headlight
LH headlight fuse
1C operation (low Dimmer switch at low
(low beam) position Below 1.5 • Inspect LH headlight
beam) beam position
• Inspect related harness
Headlight switch at OFF or TNS
Below 1.5
position
• Inspect HEAD C/U 7.5
HEAD C/U 7.5
1D Power supply Under any condition B+ A fuse
A fuse
• Inspect related harness
DRL control
Constant: inspect for continuity to
1E module GND Yes • Inspect related harness
ground
ground

09–18–18
1712-1U-01G(09-18).fm 19 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
Voltage (V)/
Terminal Signal Connected to Test condition Action
Continuity
Headlight Dimmer switch at high • Inspect headlight
Below 1.0
switch at beam position • Inspect HEAD R 15 A
Headlight headlight
Headlight Dimmer switch at low fuse
1F operation B+
(high beam) position beam position • Inspect HEAD L 15 A
(high beam)
Headlight switch at OFF or TNS fuse
Below 1.0 • Inspect related harness
position
Headlight switch at headlight position Below 1.0 • Inspect headlight relay
Headlight
Headlight (See 09–21–5 RELAY
2A relay Headlight switch at OFF or TNS
relay B+ INSPECTION)
operation position • Inspect related harness
Flash-to-pass activated Below 1.0 • Inspect combination
Flash-to-pass Headlight
2B switch
on/off switch Flash-to-pass not activated B+ • Inspect related harness
2C — — — — —
Brake fluid level is • Inspect METER 10 A
Below 1.0
Ignition switch below MIN. fuse
at ON position Brake fluid level is • Inspect instrument
B+ cluster
• Brake above MIN.
(See 09–22–4
system
INSTRUMENT
Brake system warning
CLUSTER
2D warning light light
INSPECTION)
operation • Brake fluid
Ignition switch at LOCK or ACC • Inspect brake fluid level
level Below 1.0
position sensor
sensor
(See 04–11–9 FLUID
LEVEL SENSOR
INSPECTION)
• Inspect related harness
09–18
• Headlight Dimmer switch at high
B+
switch at beam position • Inspect front fog light
Front fog light headlight relay
Front fog light
2E relay position (See 09–21–5 RELAY
switch Dimmer switch at low
operation • Front fog Below 1.5 INSPECTION)
light switch beam position • Inspect related harness
on
Parking brake Parking brake lever pulled Below 1.0 • Inspect parking brake
Parking brake
2F lever pulled/ switch
switch Parking brake lever released B+
released • Inspect related harness
Dimmer switch at high beam position Below 1.0 • Inspect combination
High beam Headlight
2G switch
on/off switch Dimmer switch at low beam position B+ • Inspect related harness
Headlight switch at headlight position Below 1.0 • Inspect combination
Headlight Headlight
2H Headlight switch at OFF or TNS switch
switch on/off switch B+
position • Inspect related harness

End Of Sie

09–18–19
1712-1U-01G(09-18).fm 20 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
INTERIOR AND MAP LIGHT REMOVAL/INSTALLATION
A3U091851310W01
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
1 Lens
(See 09–18–20 Lens Removal Note)
2 Interior light bulb
3 Map light bulb
4 Screw
5 Interior and map light
6 Connector

3. Install in the reverse order of removal.

X3U918WAW

Lens Removal Note

1. Insert a tape-wrapped, flathead screwdriver into
the service hole.
2. Twist the flathead screwdriver in the direction
indicated by the arrow to remove the lens.
End Of Sie

X3U918WAX

INTERIOR AND MAP LIGHT INSPECTION

A3U091851310W02
1. Remove the interior and map light. (See 09–18–20 INTERIOR AND MAP LIGHT REMOVAL/INSTALLATION.)
2. Inspect for continuity between the interior and map light terminals using an ohmmeter.
• If not as specified, replace the interior and map light.

Y3U918WAK Z3U0918W004

End Of Sie

09–18–20
1712-1U-01G(09-18).fm 21 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
MAP LIGHT REMOVAL/INSTALLATION
A3U091851310W03
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
1 Lens
(See 09–18–21 Lens Removal Note)
2 Map light bulb
3 Map light
4 Connector

3. Install in the reverse order of removal.

X3U918WAZ

Lens Removal Note 09–18

1. Insert a tape-wrapped, flathead screwdriver into
the service hole.
2. Twist the flathead screwdriver in the direction
indicated by the arrow to remove the lens.
End Of Sie

X3U918WB0

MAP LIGHT INSPECTION

A3U091851310W04
1. Remove the map light. (See 09–18–21 MAP LIGHT REMOVAL/INSTALLATION.)
2. Inspect for continuity between the map light terminals using an ohmmeter.
• If not as specified, replace the map light.

X3U918WBN

End Of Sie

Y3U918WAB

09–18–21
1712-1U-01G(09-18).fm 22 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
INTERIOR LIGHT REMOVAL/INSTALLATION
A3U091869970W01
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
1 Lens
(See 09–18–22 Lens Removal Note)
2 Interior light bulb
3 Screw
4 Interior light
5 Connector

3. Install in the reverse order of removal.

X3U918WB2

Lens Removal Note

1. Insert a tape-wrapped, flathead screwdriver into
the service hole.
2. Twist the flathead screwdriver in the direction
indicated by the arrow to remove the lens.
End Of Sie

X3U918WB3

INTERIOR LIGHT INSPECTION

A3U091869970W02
1. Remove the interior light. (See 09–18–22 INTERIOR LIGHT REMOVAL/INSTALLATION.)
2. Inspect for continuity between the interior light terminals using an ohmmeter.
• If not as specified, replace the interior light.

X3U918WBP

End Of Sie
Z3U0918W005

09–18–22
1712-1U-01G(09-18).fm 23 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
TRUNK COMPARTMENT LIGHT BULB REMOVAL/INSTALLATION
A3U091851440W01
1. Disconnect the negative battery cable.
2. Pinch the sides of the lens and pull down to
remove.
3. Remove the bulb.
4. Install in the reverse order of removal.
End Of Sie

X3U918WB5

TRUNK COMPARTMENT LIGHT SWITCH INSPECTION

A3U091851440W02

Note
• Trunk compartment light switch has a built-in trunk lid lock.

1. Disconnect the trunk compartment light switch connector.

2. Inspect for continuity between the trunk compartment light switch terminal and a body ground using an
ohmmeter.
• If not as specified, replace the trunk lid lock.

09–18

X3U918WBQ

End Of Sie

Y3U918WAD

CARGO COMPARTMENT LIGHT REMOVAL/INSTALLATION

A3U091851441W01
1. Disconnect the negative battery cable.
2. Pinch the sides of the lens and pull to remove.
3. Remove the cargo compartment light bulb.
4. Push the area indicated by the arrow and pull to remove the cargo compartment light.
5. Disconnect the connectors.
6. Install in the reverse order of removal.
End Of Sie

A3U0918W005

09–18–23
1712-1U-01G(09-18).fm 24 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
CARGO COMPARTMENT LIGHT INSPECTION A3U091851441W02
1. Remove the cargo compartment light. (See 09–18–23 CARGO COMPARTMENT LIGHT REMOVAL/
INSTALLATION.)
2. Inspect for continuity between the cargo
compartment light terminals using an ohmmeter.
• If not as specified, replace the cargo
compartment light.

A3U0918W007
YMU918WB7

End Of Sie
CARGO COMPARTMENT LIGHT SWITCH INSPECTION A3U091851442W01
1. Remove the liftgate trim. (See 09–17–16 LIFTGATE TRIM REMOVAL/INSTALLATION.)
2. Disconnect the cargo compartment light switch connector.
3. Inspect for continuity between the cargo
compartment light switch terminals using an
ohmmeter.
• If not as specified, replace the liftgate lock.

Y3U918WAD
YMU918WB9

End Of Sie
IGNITION KEY ILLUMINATION BULB REMOVAL/INSTALLATION A3U091860231W01
1. Disconnect the negative battery cable.
2. Remove the column cover.
3. Remove the ignition key illumination bulb.
4. Install in the reverse order of removal.
End Of Sie

Z3U0918W015

DOOR SWITCH REMOVAL/INSTALLATION A3U091866540W01

Front
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
1 Screw
2 Connector
3 Door switch

3. Install in the reverse order of removal.

Y3U918WAE

09–18–24
1712-1U-01G(09-18).fm 25 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
Rear
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
1 Screw
2 Connector
3 Door switch

3. Install in the reverse order of removal.

End Of Sie

Y3U918WAF

DOOR SWITCH INSPECTION

A3U091866540W02
1. Remove the door switch. (See 09–18–24 DOOR SWITCH REMOVAL/INSTALLATION.)
2. Inspect for continuity between the door switch terminal and a body ground using an ohmmeter.
• If not as specified, replace the door switch.

X3U918WBR

End Of Sie 09–18

X3U918WB9

PANEL LIGHT CONTROL SWITCH REMOVAL/INSTALLATION

A3U091866600W01
1. Disconnect the negative battery cable.
2. Remove the driver-side side panel.
3. Remove in the order indicated in the table.
1 Panel light control switch
(See 09–18–25 Panel Light Control Switch Removal
Note)
2 Connector

4. Install in the reverse order of removal.

Y3U918WAS

Panel Light Control Switch Removal Note

1. Insert your hand into the hole in the driver-side side panel, grasp the tabs of the panel light control switch and
pull it forward to remove.
End Of Sie

09–18–25
1712-1U-01G(09-18).fm 26 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
PANEL LIGHT CONTROL SWITCH INSPECTION
A3U091866600W02
1. Remove the panel light control switch. (See 09–18–25 PANEL LIGHT CONTROL SWITCH REMOVAL/
INSTALLATION.)
2. Connect the negative battery cable.
3. Connect the connector to the panel light control switch.
4. Measure the voltage at the panel light control switch as indicated below.
5. Disconnect the panel light control switch connector before inspecting for continuity at terminal D.
• If not as specified, inspect the parts listed under “Action.”
• If the parts and wiring harnesses are okay but the system still does not work properly, replace the panel
light control switch.

Terminal Voltage List (Reference)

Y3U918WAG

Voltage (V)/
Terminal Signal Connected to Test condition Action
Continuity
A — — — — —
Headlight switch at TNS or headlight • Inspect TNS
B+
position relay
• Inspect
combination
B TNS TNS relay switch
Other Below 1.0 • Inspect TAIL 15 A
fuse
• Inspect related
harness
• Inspect each
Inspect using an oscilloscope illumination
C Illumination Each illumination —
(See 09–18–26 Terminal C inspection) • Inspect related
harness
Constant: inspect for continuity to
D Ground GND Yes • Inspect GND
ground

Terminal C inspection
1. Measure the wave pattern of the C terminal on
the panel light control switch using an
oscilloscope.
2. Set the headlight switch to either the TNS or
headlight position.
3. Set the panel light control switch to the brightest
position.

X3U918WBC

4. Verify that the pattern on the screen is as shown

in the figure.

X3U918WBD

09–18–26
1712-1U-01G(09-18).fm 27 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS
5. Verify that the pattern on the screen matches the
pattern shown in the figure as the panel light
control switch is gradually turned to the darkest
position.
End Of Sie

X3U918WBE

09–18

09–18–27