Scribd Logo
Upload

Welcome to Scribd!

  • 182 views

    Nalsize 7541: Emulsification Aid

    Uploaded by

    alakazum28
    Ficha tecnica nalco

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Nalsize 7541: Emulsification Aid

    Uploaded by

    alakazum28
    182 views3 pages
    Ficha tecnica nalco

    Original Title

    7541

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Ficha tecnica nalco

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    182 views3 pages

    Nalsize 7541: Emulsification Aid

    Uploaded by

    alakazum28
    Ficha tecnica nalco

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    NALSIZE™ 7541

    Emulsification Aid
    Product Bulletin

    PRODUCT DESCRIPTION AND APPLICATION

    NALCO 7541 is a liquid cationic polyacrylamide that is used to emulsify NALSIZE 7542, NALCO’s ASA
    sizing agents. The NALSIZE emulsion is prepared by mixing NALCO 7541, or NALCO 7542 and water in
    a Nalco Turbine Emulsifier. NALCO 7541 is a unique polymer protected under several United States
    Patents and similar International Patents NALCO 7541 produces a stable, cationic ASA emulsion, which
    assists in the electrostatic retention of ASA to cellulose.

    PHYSICAL & CHEMICAL PROPERTIES

    These properties are typical. Refer to the Safety Data Sheet (SDS) for the most current data.

    Form Liquid
    Color Colorless-Light yellow
    Odor None
    Boiling point 100°C (212°F) ASTM D-86
    Vapor pressure same as water
    Relative density 1.055-1.075 g/cm3 ASTM D-1298
    Solubility in water Complete
    pH (Neat), 20°C (68°F) 3.0-4.0 ASTM E-70
    Viscosity @ 20°C (68°F) 1200 cps ASTM D-2983
    Freezing point <-25°C (-13°F) ASTM D-1177

    Abbreviation: NE = not evaluated, NA = not applicable, NR = not relevant

    ACTIVE CONSTITUENTS

    Refer to SDS for current information. 1. Polyacrylamide 30%

    REGULATORY APPROVALS

    NALCO 7541 is acceptable under FDA regulation 21CFR 176.170 for use as a component of paper and
    paperboard in contact with aqueous and fatty foods. NALCO 7541 is also approved by BGA (BfR
    XXXVI). For the complete list of approvals refer to the Regulatory Certifications (RCR) document.
    MATERIALS OF COMPATIBILITY

    Compatible Not Compatible


    Stainless Steel 304 & 316 Mild Steel
    PVC Iron
    Kynar Brass
    Viton® synthetic rubber Copper
    Fluoropolymer
    Polyethylene
    Polypropylene

    DOSAGE AND FEEDING

    The recommended dosage will vary depending on NALSIZE dosage and water quality. An acceptable
    level is 1:1 ratio of NALCO 7541 to NALCO 7542 (as received basis). The ASA emulsion should be kept
    at a pH < 5.0. In highly alkaline fresh waters, it may be necessary to increase the NALCO 7541 dose
    slightly (up to 1.2:1 ratio) to control the pH below this target. NALCO 7541 is designed to be used only
    with and NALCO 7542 and Nalco Turbine Emulsifier. The Nalco sizing system is designed to provide the
    best emulsion quality yielding optimum sizing performance. Sizing emulsion temperature should be kept
    below 35°C (95°F). Most accounts run a ratio of 0.75-0.80/ 1.0 of NALCO 7541 to NALSIZE ASA.

    ENVIRONMENTAL AND TOXICITY DATA

    Biological Oxygen Demand (BOD): Not available


    Chemical Oxygen Demand (COD): Not available
    Total Organic Carbon (TOC): Not available

    Refer to the SDS for the most current data.

    SAFETY AND HANDLING


    As with any chemical, NALCO 7541 should be handled with responsible care. When considering the use
    of NALCO 7541 in a particular application, review the SDS and assure that the use you intend can be
    accomplished safely. All precautions described in the SDS should be strictly followed when handling
    NALCO 7541.

    STORAGE

    NALCO 7541 should be stored at temperatures between 5 and 45°C (approximately 40 and 115°F).
    Should the product be exposed to freezing temperatures, complete recovery will occur on thawing.
    Corrosion-resistant materials are recommended for storage and transfer. Bulk storage tanks should be
    constructed of polyethylene or fiberglass. Suggested in mill storage is maximum one year if unopened
    and maintained at room temperature.
    REMARKS
    If you need assistance or more information on this product, please call your nearest NALCO Water
    representative.

    For more news about NALCO Water, an Ecolab company, visit our website www.nalco.ecolab.com

    For Medical and Transportation Emergencies involving NALCO Water products, please see the Safety
    Data Sheet for the phone number.

    ADDITIONAL INFORMATION

    If you need assistance or more information on this product, please call your nearest Nalco
    Representative. For more news about Nalco Company, visit our website at www.nalco.com. For Medical
    and Transportation Emergencies involving Nalco products, please see the Safety Data Sheet for the
    phone number.

    NAL-SIZE, Nalco and the Logo are trademarks of Ecolab USA Inc.
    All other trademarks are the property of their respective owners.
    ©2014 Ecolab USA Inc. All Rights Reserved.

    NALCO Water, An Ecolab Company

    Subsidiaries and Affiliates in Principal Locations Around the World


    ©2017 Ecolab USA, Inc. All Rights Reserved

    You might also like