Daf Dtc Codes

Full download: http://manualplace.com/download/daf-dtc-codes/

Node DTC ISO FailureEvent FTB_Name FunctBehaviorDesc PossibleRootCause ProcedureEraseConfirmed ProposedWorkshopAction ProprietaryName
Check:
Lost communication on High Speed
((It has not been possible to send frames CAN Communication Bus
on High Speed CAN Communication Bus)
and (It has not been possible to receive Lost communication on High Diagnostic Service 14. No If fault not detected:
frames on High Speed CAN Speed CAN Communication additional action is Fault trace according to Tech Tool CAN Communication
ACM U000188 Communication Bus)) Bus off None Bus needed. fault tree. Backbone 2 Net
Check:
Lost communication on Medium
((It has not been possible to send frames Speed CAN Communication Bus
on Medium Speed CAN Communication
Bus) and (It has not been possible to Auxiliary brakes, low Lost communication on Diagnostic Service 14. No If fault not detected:
receive frames on Medium Speed CAN performance (Reduced Medium Speed CAN additional action is Fault trace according to Tech Tool CAN Communication
ACM U001088 Communication Bus)) Bus off retarder braking) Communication Bus needed. fault tree. Backbone 1 Net

(Lost communication with ECM on Auxiliary brakes, low ECM not powered Diagnostic Service 14. No Check:
Medium Speed CAN Communication No Sub Type performance (Reduced Software incompatibility additional action is ECM not powered Lost Communication with
ACM U010000 Bus) Information retarder braking) with ECM needed. Software incompatibility with ECM EMS

((Voltage on A:42 above 2.260742V and Check:

Voltage on A:42 below 4.852295V) or Wiring fault Diagnostic Service 14. No Wiring fault
(Voltage on A:42 above 0.147705V and General Electrical Sensor fault additional action is Sensor fault Exhaust Gas Temperature
ACM P054401 Voltage on A:42 below 0.677490V)) Failure None ECU fault needed. ECU fault Sensor Bank 1 Sensor 1
Check:
Wiring fault
Sensor fault
ECU fault

Wiring fault Diagnostic Service 14. No If fault not detected:

Circuit Short To Regeneration not Sensor fault additional action is Fault trace according to Tech Tool Exhaust Gas Temperature
ACM P054411 Voltage on A:42 below 0.147705V Ground possible ECU fault needed. fault tree. Sensor Bank 1 Sensor 1
Check:
Wiring fault
Sensor fault
ECU fault

Wiring fault Diagnostic Service 14. No If fault not detected:

Circuit Short To Regeneration not Sensor fault additional action is Fault trace according to Tech Tool Exhaust Gas Temperature
ACM P054415 Voltage on A:42 above 4.852295V Battery or Open possible ECU fault needed. fault tree. Sensor Bank 1 Sensor 1
Check:
Wiring fault Diagnostic Service 14. No Wiring fault
(Voltage on A:18 above 4.794922V and General Electrical Sensor fault additional action is Sensor fault Reductant Tank
ACM P205A01 Voltage on A:18 below 4.852295V) Failure None ECU fault needed. ECU fault Temperature Sensor
Check:
Wiring fault Diagnostic Service 14. No Wiring fault
Circuit Short To Sensor fault additional action is Sensor fault Reductant Tank
ACM P205A11 Voltage on A:18 below 0.037842V Ground None ECU fault needed. ECU fault Temperature Sensor

This is the cut pages sample. Download all 83 page(s) at: ManualPlace.com
Node DTC ISO FailureEvent FTB_Name FunctBehaviorDesc PossibleRootCause ProcedureEraseConfirmed ProposedWorkshopAction ProprietaryName
Check:
Wiring fault Diagnostic Service 14. No Wiring fault
Sensor fault additional action is Sensor fault Reductant Tank
ACM P205A13 Voltage on A:18 above 4.852295V Circuit Open None ECU fault needed. ECU fault Temperature Sensor

Check:
Coolant level low
Extremely cold weather conditions
Coolant valve damaged
Coolant level low
Extremely cold weather Diagnostic Service 14. No If fault not detected:
Signal Plausibility conditions additional action is Fault trace according to Tech Tool Reductant Tank
ACM P205A64 (Temperature rise not above 3°C) Failure None Coolant valve damaged needed. fault tree. Temperature Sensor
Diagnostic Service 14. No
General Checksum additional action is Check:
ACM U300041 (Program memory corruption) Failure Engine does not start Download issue needed. Download issue Electronic control unit
Diagnostic Service 14. No
Data Memory additional action is Check:
ACM U300044 (RAM corruption) Failure Engine does not start Download issue needed. Download issue Electronic control unit
Diagnostic Service 14. No
(Program memory corruptionSoftware Program Memory additional action is Check:
ACM U300045 memory checksum error) Failure Engine does not start Download issue needed. Download issue Electronic control unit
Diagnostic Service 14. No
Internal Electronic additional action is Check:
ACM U300049 (ECU internal error) Failure Engine does not start ECU Hardware issue needed. ECU Hardware issue Electronic control unit

((Voltage on A:34 above 2.260742V and Check:

Voltage on A:34 below 4.852295V) or Wiring fault Diagnostic Service 14. No Wiring fault
(Voltage on A:34 above 0.147705V and General Electrical Sensor fault additional action is Sensor fault Exhaust Gas Temperature
ACM P203101 Voltage on A:34 below 0.677490V)) Failure None ECU fault needed. ECU fault Sensor Bank 1 Sensor 2
Check:
Wiring fault
Sensor fault
ECU fault

Wiring fault Diagnostic Service 14. No If fault not detected:

Circuit Short To Sensor fault additional action is Fault trace according to Tech Tool Exhaust Gas Temperature
ACM P203111 Voltage on A:34 below 0.147705V Ground None ECU fault needed. fault tree. Sensor Bank 1 Sensor 2
Check:
Wiring fault
Sensor fault
ECU fault

Wiring fault Diagnostic Service 14. No If fault not detected:

Circuit Short To Sensor fault additional action is Fault trace according to Tech Tool Exhaust Gas Temperature
ACM P203115 Voltage on A:34 above 4.852295V Battery or Open None ECU fault needed. fault tree. Sensor Bank 1 Sensor 2
Node DTC ISO FailureEvent FTB_Name FunctBehaviorDesc PossibleRootCause ProcedureEraseConfirmed ProposedWorkshopAction ProprietaryName
Check:
Wiring fault
Sensor fault
ECU fault

Wiring fault Diagnostic Service 14. No If fault not detected:

Circuit Short To Sensor fault additional action is Fault trace according to Tech Tool Particulate Filter Pressure
ACM P245211 Voltage on A:26 below 0.147705V Ground None ECU fault needed. fault tree. Sensor "A"
Check:
Wiring fault
Sensor fault
ECU fault

Wiring fault Diagnostic Service 14. No If fault not detected:

Sensor fault additional action is Fault trace according to Tech Tool Particulate Filter Pressure
ACM P245213 Voltage on A:26 above 4.901123V Circuit Open None ECU fault needed. fault tree. Sensor "A"

Harness, actuator or Diagnostic Service 14. No Check:

Circuit Short To connector is short circuited additional action is Harness, actuator or connector is Reductant Heater "B"
ACM P20BD11 (Short circuit to ground is detected.) Ground None to ground voltage. needed. short circuited to ground voltage. Control

Harness, actuator or Diagnostic Service 14. No Check:

Circuit Short To connector is short circuited additional action is Harness, actuator or connector is Reductant Heater "B"
ACM P20BD12 (Short circuit to battery is detected.) Battery None to battery voltage. needed. short circuited to battery voltage. Control
Diagnostic Service 14. No Check:
Open circuit in harness, additional action is Open circuit in harness, actuator or Reductant Heater "B"
ACM P20BD13 (Open circuit fault is detected.) Circuit Open None actuator or connector. needed. connector. Control

Check:
BCM not powered
Software incompatibility with BCM

(Lost communication with BCM on BCM not powered Diagnostic Service 14. No If fault not detected:
Medium Speed CAN Communication No Sub Type Software incompatibility additional action is Fault trace according to Tech Tool Lost Communication With
ACM U014100 Bus) Information None with BCM needed. fault tree. VMCU

Check:
IPC not powered
Software incompatibility with IPC

(Lost communication with IPC on IPC not powered Diagnostic Service 14. No If fault not detected: Lost Communication With
Medium Speed CAN Communication No Sub Type Software incompatibility additional action is Fault trace according to Tech Tool Instrument Panel Cluster
ACM U015500 Bus) Information None with IPC needed. fault tree. (IPC) Control Module
Node DTC ISO FailureEvent FTB_Name FunctBehaviorDesc PossibleRootCause ProcedureEraseConfirmed ProposedWorkshopAction ProprietaryName
((Voltage on N/A:ECU internal above
2.874756V and Voltage on N/A:ECU
internal below 4.852295V) or (Voltage Check:
on N/A:ECU internal above 0.147705V Wiring fault Diagnostic Service 14. No Wiring fault
and Voltage on N/A:ECU internal below General Electrical Sensor fault additional action is Sensor fault Control Module Internal
ACM P066601 1.237793V)) Failure None ECU fault needed. ECU fault Temperature Sensor "A"
Check:
Wiring fault Diagnostic Service 14. No Wiring fault
Voltage on N/A:ECU internal below Circuit Short To Sensor fault additional action is Sensor fault Control Module Internal
ACM P066611 0.147705V Ground None ECU fault needed. ECU fault Temperature Sensor "A"
Check:
Wiring fault Diagnostic Service 14. No Wiring fault
Voltage on N/A:ECU internal above Sensor fault additional action is Sensor fault Control Module Internal
ACM P066613 4.852295V Circuit Open None ECU fault needed. ECU fault Temperature Sensor "A"

((Voltage on A:11 above 2.214355V and Check:

Voltage on A:11 below 4.852295V) or Auxiliary brakes, low Wiring fault Diagnostic Service 14. No Wiring fault
(Voltage on A:11 above 0.147705V and General Electrical performance (Reduced Sensor fault additional action is Sensor fault Retarder Water
ACM P107B01 Voltage on A:11 below 1.165771V)) Failure retarder braking) ECU fault needed. ECU fault Temperature Sensor
Check:
Auxiliary brakes, low Wiring fault Diagnostic Service 14. No Wiring fault
Circuit Short To performance (Reduced Sensor fault additional action is Sensor fault Retarder Water
ACM P107B11 Voltage on A:11 below 0.147705V Ground retarder braking) ECU fault needed. ECU fault Temperature Sensor
Check:
Auxiliary brakes, low Wiring fault Diagnostic Service 14. No Wiring fault
performance (Reduced Sensor fault additional action is Sensor fault Retarder Water
ACM P107B13 Voltage on A:11 above 4.852295V Circuit Open retarder braking) ECU fault needed. ECU fault Temperature Sensor

((Voltage on A:15 above 2.214355V and Check:

Voltage on A:15 below 4.852295V) or Wiring fault Diagnostic Service 14. No Wiring fault
(Voltage on A:15 above 0.147705V and General Electrical Sensor fault additional action is Sensor fault Retarder Oil Temperature
ACM P107C01 Voltage on A:15 below 1.165771V)) Failure None ECU fault needed. ECU fault Sensor
Check:
Wiring fault Diagnostic Service 14. No Wiring fault
Circuit Short To Sensor fault additional action is Sensor fault Retarder Oil Temperature
ACM P107C11 Voltage on A:15 below 0.147705V Ground None ECU fault needed. ECU fault Sensor
Check:
Wiring fault Diagnostic Service 14. No Wiring fault
Sensor fault additional action is Sensor fault Retarder Oil Temperature
ACM P107C13 Voltage on A:15 above 4.852295V Circuit Open None ECU fault needed. ECU fault Sensor

Component or Auxiliary brakes, low Diagnostic Service 14. No Check:

( The retarder oil temperature is above System Over performance (Reduced Bad cooling additional action is Bad cooling Retarder Oil Temperature
ACM P107C98 critical limit. ) Temperature retarder braking) Sensor malfunction needed. Sensor malfunction Sensor

Auxiliary brakes, low Harness, actuator or Diagnostic Service 14. No Check:

Circuit Short To performance (Reduced connector is short circuited additional action is Harness, actuator or connector is
ACM P107D11 (Short circuit to ground is detected.) Ground retarder braking) to ground voltage. needed. short circuited to ground voltage. Retarder Valve
Node DTC ISO FailureEvent FTB_Name FunctBehaviorDesc PossibleRootCause ProcedureEraseConfirmed ProposedWorkshopAction ProprietaryName

Auxiliary brakes, low Harness, actuator or Diagnostic Service 14. No Check:

Circuit Short To performance (Reduced connector is short circuited additional action is Harness, actuator or connector is
ACM P107D12 (Short circuit to battery is detected.) Battery retarder braking) to battery voltage. needed. short circuited to battery voltage. Retarder Valve

Auxiliary brakes, low Diagnostic Service 14. No Check:

performance (Reduced Open circuit in harness, additional action is Open circuit in harness, actuator or
ACM P107D13 (Open circuit fault is detected.) Circuit Open retarder braking) actuator or connector. needed. connector. Retarder Valve

((Voltage on A:19 above 4.797363V and Check:

Voltage on A:19 below 4.852295V) or Auxiliary brakes, low Wiring fault Diagnostic Service 14. No Wiring fault
(Voltage on A:19 above 0.147705V and General Electrical performance (Reduced Sensor fault additional action is Sensor fault Retarder Air Pressure
ACM P107E01 Voltage on A:19 below 0.202637V)) Failure retarder braking) ECU fault needed. ECU fault Sensor
Check:
Auxiliary brakes, low Wiring fault Diagnostic Service 14. No Wiring fault
Circuit Short To performance (Reduced Sensor fault additional action is Sensor fault Retarder Air Pressure
ACM P107E12 Voltage on A:19 above 4.852295V Battery retarder braking) ECU fault needed. ECU fault Sensor
Check:
Auxiliary brakes, low Wiring fault Diagnostic Service 14. No Wiring fault
performance (Reduced Sensor fault additional action is Sensor fault Retarder Air Pressure
ACM P107E13 Voltage on A:19 below 0.147705V Circuit Open retarder braking) ECU fault needed. ECU fault Sensor

( Too big difference between requested Auxiliary brakes, low Retarder valve malfunction Diagnostic Service 14. No Check:
retarder pressure and actual retarder Signal Plausibility performance (Reduced Air pressure sensor additional action is Retarder valve malfunction Retarder Air Pressure
ACM P107E64 pressure. ) Failure retarder braking) malfunction needed. Air pressure sensor malfunction Sensor

Auxiliary brakes, low Retarder valve malfunction Diagnostic Service 14. No Check:
( The retarder air pressure is above Signal Above performance (Reduced Air pressure sensor additional action is Retarder valve malfunction Retarder Air Pressure
ACM P107E85 critical limit. ) Allowable Range retarder braking) malfunction needed. Air pressure sensor malfunction Sensor
((Voltage on A:27 above 4.65V and Check:
Voltage on A:27 below 4.85V) or Wiring fault Diagnostic Service 14. No Wiring fault
(Voltage on A:27 above 0.147V and General Electrical Sensor fault additional action is Sensor fault
ACM P204A01 Voltage on A:27 below 0.3V)) Failure None ECU fault needed. ECU fault Reductant Pressure Sensor
Check:
Wiring fault
Sensor fault
ECU fault

Wiring fault Diagnostic Service 14. No If fault not detected:

Circuit Short To Sensor fault additional action is Fault trace according to Tech Tool
ACM P204A11 Voltage on A:27 below 0.147V Ground None ECU fault needed. fault tree. Reductant Pressure Sensor
Node DTC ISO FailureEvent FTB_Name FunctBehaviorDesc PossibleRootCause ProcedureEraseConfirmed ProposedWorkshopAction ProprietaryName
Check:
Wiring fault
Sensor fault
ECU fault

Wiring fault Diagnostic Service 14. No If fault not detected:

Sensor fault additional action is Fault trace according to Tech Tool
ACM P204A13 Voltage on A:27 above 4.85V Circuit Open None ECU fault needed. fault tree. Reductant Pressure Sensor

(ACM_AirPressure above 250kPa or Check:

((Difference between inital reductant Faulty urea pressure sensor
pressure and final reductant pressure Blocked urea line or nozzle
during startup) above 30kPa and not
((Difference between inital air pressure Diagnostic Service 14. No If fault not detected:
and final air pressure during startup) Signal Plausibility Faulty urea pressure sensor additional action is Fault trace according to Tech Tool
ACM P204A64 above 20kPa))) Failure None Blocked urea line or nozzle needed. fault tree. Reductant Pressure Sensor

Harness, actuator or Diagnostic Service 14. No Check:

Circuit Short To connector is short circuited additional action is Harness, actuator or connector is Reductant Pump "A"
ACM P208A11 (Short circuit to ground is detected.) Ground None to ground voltage. needed. short circuited to ground voltage. Control
Harness, actuator or Diagnostic Service 14. No Check:
Circuit Short To connector short circuited to additional action is Harness, actuator or connector Reductant Pump "A"
ACM P208A12 (Short circuit to battery is detected.) Battery None battery. needed. short circuited to battery. Control
Diagnostic Service 14. No Check:
Open circuit in harness, additional action is Open circuit in harness, actuator or Reductant Pump "A"
ACM P208A13 (Open circuit is detected.) Circuit Open None actuator or connector. needed. connector. Control
Check:
Bad pins or connection. Diagnostic Service 14. No Bad pins or connection.
Signal Below Cabling issues. additional action is Cabling issues.
ACM P056084 not ( Control Module below 8V) Allowable Range None Generator issues. needed. Generator issues. System Voltage
Check:
Bad pins or connection. Diagnostic Service 14. No Bad pins or connection.
Signal Above Cabling issues. additional action is Cabling issues.
ACM P056085 not ( Control Module above 36V) Allowable Range None Generator issues. needed. Generator issues. System Voltage

Check:
Harness, actuator or connector is
short circuited to ground voltage.

Harness, actuator or Diagnostic Service 14. No If fault not detected:

Circuit Short To connector is short circuited additional action is Fault trace according to Tech Tool Reductant Heater Coolant
ACM P20B111 (Short circuit to ground is detected.) Ground None to ground voltage. needed. fault tree. Control Valve Control

Harness, actuator or Diagnostic Service 14. No Check:

Circuit Short To connector is short circuited additional action is Harness, actuator or connector is Reductant Heater Coolant
ACM P20B112 (Short circuit to battery is detected.) Battery None to battery voltage. needed. short circuited to battery voltage. Control Valve Control
Node DTC ISO FailureEvent FTB_Name FunctBehaviorDesc PossibleRootCause ProcedureEraseConfirmed ProposedWorkshopAction ProprietaryName
Diagnostic Service 14. No Check:
Open circuit in harness, additional action is Open circuit in harness, actuator or Reductant Heater Coolant
ACM P20B113 (Open circuit fault is detected.) Circuit Open None actuator or connector. needed. connector. Control Valve Control
Check:
Tankheatvalve stuck open
Inappropriate location of the pump
or tank

(Reductant Tank Temperature above Tankheatvalve stuck open Diagnostic Service 14. No If fault not detected:
70°C or Reductant Pump Temperature Actuator Stuck Inappropriate location of additional action is Fault trace according to Tech Tool Reductant Heater Coolant
ACM P20B172 above 120°C) Open None the pump or tank needed. fault tree. Control Valve Control
Check:
Coolan valve damaged
Coolat valve stuck

Diagnostic Service 14. No If fault not detected:

((Temperature rise not above 3°C) and Actuator Stuck Coolan valve damaged additional action is Fault trace according to Tech Tool Reductant Heater Coolant
ACM P20B173 (Temperature rise not above 5°C)) Closed None Coolat valve stuck needed. fault tree. Control Valve Control

Harness, actuator or Diagnostic Service 14. No Check:

Circuit Short To connector is short circuited additional action is Harness, actuator or connector is Reductant Heater "A"
ACM P20B911 (Short circuit to ground is detected.) Ground None to ground voltage. needed. short circuited to ground voltage. Control

Harness, actuator or Diagnostic Service 14. No Check:

Circuit Short To connector is short circuited additional action is Harness, actuator or connector is Reductant Heater "A"
ACM P20B912 (Short circuit to battery is detected.) Battery None to battery voltage. needed. short circuited to battery voltage. Control
Diagnostic Service 14. No Check:
Open circuit in harness, additional action is Open circuit in harness, actuator or Reductant Heater "A"
ACM P20B913 (Open circuit fault is detected.) Circuit Open None actuator or connector. needed. connector. Control
Check:
Heating valve stuck close
Electrical heaters failure

Diagnostic Service 14. No If fault not detected:

(Start the engine and drive the truck Performance or Heating valve stuck close additional action is Fault trace according to Tech Tool Reductant Heater "A"
ACM P20B992 during cold weather conditions) Incorrect Operation None Electrical heaters failure needed. fault tree. Control
Check:
Damaged checkvalve

Diagnostic Service 14. No If fault not detected:

Actuator Stuck additional action is Fault trace according to Tech Tool Reductant Purge Control
ACM P20A072 Reagent Pressure AlbonAir above 30kPa Open None Damaged checkvalve needed. fault tree. Valve
Daf Dtc Codes
Full download: http://manualplace.com/download/daf-dtc-codes/

Node DTC ISO FailureEvent FTB_Name FunctBehaviorDesc PossibleRootCause ProcedureEraseConfirmed ProposedWorkshopAction ProprietaryName

(not ((Difference between inital

reductant pressure and final reductant Check:
pressure during startup) above 30kPa) Damaged checkvalve
and (Difference between inital air
pressure and final air pressure during Diagnostic Service 14. No If fault not detected:
startup) above 20kPa and (Pump priming Actuator Stuck additional action is Fault trace according to Tech Tool Reductant Purge Control
ACM P20A073 has been completed)) Closed None Damaged checkvalve needed. fault tree. Valve

((Voltage on A:46 above 4.582520V and Check:

Voltage on A:46 below 4.852295V) or Wiring fault Diagnostic Service 14. No Wiring fault
(Voltage on A:46 above 0.147705V and General Electrical Sensor fault additional action is Sensor fault
ACM P203A01 Voltage on A:46 below 0.457764V)) Failure None ECU fault needed. ECU fault Reductant Level Sensor "A"
Check:
Wiring fault Diagnostic Service 14. No Wiring fault
Circuit Short To Sensor fault additional action is Sensor fault
ACM P203A12 Voltage on A:46 above 4.852295V Battery None ECU fault needed. ECU fault Reductant Level Sensor "A"
Check:
Wiring fault Diagnostic Service 14. No Wiring fault
Sensor fault additional action is Sensor fault
ACM P203A13 Voltage on A:46 below 0.147705V Circuit Open None ECU fault needed. ECU fault Reductant Level Sensor "A"
Check:
Connector/pins issues
Cabling issues

Diagnostic Service 14. No If fault not detected:

not ( Control Module between 20V and Connector/pins issues additional action is Fault trace according to Tech Tool Reductant Control Module
ACM P21CAA1 32V) System Voltage None Cabling issues needed. fault tree. Supply Voltage
Check:
Damaged pump
Empty Urea tank
Leak in suction line

not ((Turn engine on and run truck with Damaged pump Diagnostic Service 14. No If fault not detected:
medium to high load during at least 10 Performance or Empty Urea tank additional action is Fault trace according to Tech Tool Reductant No Flow
ACM P218F92 minutes)) Incorrect Operation None Leak in suction line needed. fault tree. Detected
Check:
Harness or connector is short
circuited to ground voltage.

Harness or connector is Diagnostic Service 14. No If fault not detected:

Circuit Short To short circuited to ground additional action is Fault trace according to Tech Tool
ACM P26E711 (Short circuit to ground is detected.) Ground None voltage. needed. fault tree. Actuator Supply Voltage "D"
Diagnostic Service 14. No Check:
(The factory mode is active through Factory Mode was not additional action is Factory Mode was not turned off by
ACM U1FFF68 P1HCF) Event Information None turned off by P1HCF needed. P1HCF Factory Mode Active

This is the cut pages sample. Download all 83 page(s) at: ManualPlace.com