[键入文字]

i20S SIP Voice Access

User Manual V1.0
[键入文字]

Document VER Firmware VER Explanation Time

V1.0 2.0.0.2485 Initial issue 20160830
[键入文字]

Safety Notices
1. Please use the specified power adapter. If you need to use the power adapter provided by other
manufacturers under special circumstances, please make sure that the voltage and current provided is
in accordance with the requirements of this product, meanwhile, please use the safety certificated
products, otherwise may cause fire or get an electric shock.
2. When using this product, please do not damage the power cord either by forcefully twist it, stretch
pull, banding or put it under heavy pressure or between items, otherwise it may cause damage to the
power cord, lead to fire or get an electric shock.
3. Before using, please confirm that the temperature and environment is humidity suitable for the
product to work. (Move the product from air conditioning room to natural temperature, which may
cause this product surface or internal components produce condense water vapor, please open power
use it after waiting for this product is natural drying).
4. Please do not let non-technical staff to remove or repair. Improper repair may cause electric shock,
fire, malfunction, etc. It will lead to injury accident or cause damage to your product.
5. Do not use fingers, pins, wire, other metal objects or foreign body into the vents and gaps. It may
cause current through the metal or foreign body, which may even cause electric shock or injury
accident. If any foreign body or objection falls into the product please stop using.
6. Please do not discard the packing bags or store in places where children could reach, if children trap
his head with it, may cause nose and mouth blocked, and even lead to suffocation.
7. Please use this product with normal usage and operating, in bad posture for a long time to use this
product may affect your health.
8. Please read the above safety notices before installing or using this phone. They are crucial for the safe
and reliable operation of the device.
[键入文字]

Directory
I. PRODUCT INTRODUCTION ................................................................................................................ 6

1. APPEARANCE OF THE PRODUCT .............................................................................................................. 6

2. DESCRIPTION .................................................................................................................................... 6

II. START USING .................................................................................................................................... 7

1. CONFIRM THE CONNECTION .................................................................................................................. 7

1) Power, Electric Lock, Indoor switch port ..................................................................................... 7
2) Driving mode of electric-lock(Default in active mode) ................................................................ 7
3) Wiring instructions .................................................................................................................... 8
2. QUICK SETTING ................................................................................................................................. 9

III. BASIC OPERATION ......................................................................................................................... 9

1. ANSWER A CALL ................................................................................................................................ 9

2. CALL ............................................................................................................................................ 10
3. END CALL....................................................................................................................................... 10
4. OPEN THE DOOR OPERATION ............................................................................................................... 10

IV. PAGE SETTINGS ........................................................................................................................... 11

1. BROWSER CONFIGURATION ................................................................................................................ 11

2. PASSWORD CONFIGURATION .............................................................................................................. 11
3. CONFIGURATION VIA WEB ................................................................................................................. 12
(1) System ................................................................................................................................. 12
a) Information .......................................................................................................................... 12
b) Account ................................................................................................................................ 13
c) Configurations ...................................................................................................................... 14
d) Upgrade ............................................................................................................................... 14
e) Auto Provision...................................................................................................................... 15
f) Tools .................................................................................................................................... 17
(2) Network ............................................................................................................................... 18
a) Basic .................................................................................................................................... 18
b) Advanced ............................................................................................................................. 19
c) VPN...................................................................................................................................... 21
(3) Line ...................................................................................................................................... 23
a) SIP ....................................................................................................................................... 23
b) Basic Settings ....................................................................................................................... 28
(4) EGS Setting........................................................................................................................... 29
[键入文字]

a) Features ............................................................................................................................... 29
b) Audio ................................................................................................................................... 32
c) MCAST ................................................................................................................................. 33
d) Action URL ........................................................................................................................... 36
e) Time/Date ............................................................................................................................ 37
(5) EGS Cards ............................................................................................................................. 38
a) EGS Cards ............................................................................................................................. 38
b) EGS ACCESS .......................................................................................................................... 40
(6) EGS Logs ............................................................................................................................... 41
(7) Function Key ........................................................................................................................ 42
a) Function Key Settings ........................................................................................................... 42

V. APPENDIX ...................................................................................................................................... 45

1. TECHNICAL PARAMETERS.................................................................................................................... 45
2. BASIC FUNCTIONS ............................................................................................................................ 46
3. SCHEMATIC DIAGRAM ....................................................................................................................... 46

VI. OTHER INSTRUCTIONS ................................................................................................................ 47

1. OPEN DOOR MODES ......................................................................................................................... 47

2. MANAGEMENT OF CARD .................................................................................................................... 48
[键入文字]

I. Product introduction
i20S voice access is a full digital network door phone, with its core part adopts mature VoIP
solution (Broadcom chip), stable and reliable performance, hands-free adopting digital full-duplex
mode, voice loud and clear, generous appearance, solid durable, easy for installation,
comfortable keypad and low power consumption.
i20S voice access supports entrance guard control, voice intercom, ID card and keypad remote
to open the door.

1. Appearance of the product

2. Description
Buttons and icons Description Function

Numeric keyboard Input password to open the door or to call.

Can be set to a variety of functions, in order to

programmable keys
meet the needs of different occasions

induction zone RFID induction area

Door unlocking: On
Lock Status
Door locking: Off
Standby: Off
Call/Ring status Calls: On
Ringing: Blink with 1s
Network error: Blink with 1s
Network/SIP Network running: Off
Registration Registration failed: Blink with 3s
Registration succeeded: On

6 / 50
[键入文字]

II. Start Using

Before you start to use the equipment, please make the following installation.

1. Confirm the connection

Confirm whether the equipment of the power cord, network cable, electric lock control line
connection and the boot-up is normal. (Check the network state of light)

1) Power, Electric Lock, Indoor switch port

Voice access the power supply ways: 12v/DC or POE.

CN7
1 2 3 4 5 6 7
+12V VSS NC COM NO S_IN S_OUT
12V 1A/DC Electric-lock switch Indoor switch

2) Driving mode of electric-lock(Default in active mode)

Jumper in passive mode Jumper in active mode

【Note】When the device is in active mode, it can drive 12V/700mA switch output maximum, to which a
standard electric-lock or another compatible electrical appliance can be connected.
 When using the active mode, it is 12V DC in output.
 When using the passive mode, output is short control (normally open mode or normally close mode).

7 / 50
[键入文字]

3) Wiring instructions
 NO: Normally Open Contact.
 COM: Common Contact.
 NC: Normally Close Contact.
Driving Mode Electric lock
No electricity When the Jumper port Connections
Active Passive
when open power to open

√ √

√ √

√ √

√ √

8 / 50
[键入文字]

2. Quick Setting
The product provides a complete function and parameter setting. Users may need to have the
network and SIP protocol knowledge to understand the meaning represented by all parameters. In
order to let equipment users enjoy the high quality of voice service and low cost advantage brought by
the device immediately, here we list some basic but compulsory setting options in this section to let
users know how to operate without understanding such complex SIP protocols.
In prior to this step, please make sure your broadband Internet online can be normal operated,
and complete the connection of the network hardware. The product factory default network mode is
DHCP. Thus, only connect equipment with DHCP network environment that network can be
automatically connected.
 Press and hold “#” key for 3 seconds and the door phone will report the IP address by voice, or use
the "iDoorPhoneNetworkScanner.exe" software to find the IP address of the device.
 Note: when power on, 30s waiting is needed for device running.
 Log on to the WEB device configuration.
 In a Line page configuration service account, user name, parameters that are required for server
address register.
 You can set DSS key in the Function key page.
 You can set Door Phone parameters in the Webpage (EGS Setting-> Features).

III. Basic operation

1. Answer a call
When a call comes in, the device will answer automatically. If you cancel auto answer feature and set
auto answer time, you will hear the bell ring at the set time and the device will auto answer after a
timeout.

9 / 50
[键入文字]

2. Call
Configure shortcut key as hot key and setup a number, then press shortcut key can call the
configured number.

3. End call
Enable Release key hang up to end call.

4. Open the door operation

Through the following seven ways to open the door:
1) Input password on the keyboard to open the door.
2) Access to call the owner and the owner enter the remote password to open the door.
3) Owner/other equipment call the access control and enter the access code to open the door. (access
code should be included in the list of access configuration, and enable for remote calls to open the
door)
4) Swipe the RFID cards to open the door.
5) By means of indoor switch to open the door.
6) Private access code to open the door.
Enable for local authentication, and set private access code. Input the access code directly under
standby mode to open the door. In this way, the door log will record corresponding card number
and user name.
7) Active URL control command to open the door.
URL is “http://user:pwd@host/cgi-bin/ConfigManApp.com?key=F_LOCK&code=openCode”
a. User and pwd is Web the user name and password.
b. “openCode” is the remote control code to open the door.
Example: “http://admin:[email protected]/cgi-bin/ConfigManApp.com?key=*”

If access code is input correctly, the device will play sirens sound to prompt access control and the
remote user, while input error by low-frequency short chirp.
Password input successfully followed by high-frequency sirens sound, while input error is followed by
high-frequency short chirp.
When door has been opened, the device will play sirens sound to prompt.

10 / 50
[键入文字]

IV. Page settings

1. Browser configuration
When the device and your computer are successfully connected to the network, enter the IP address
of the device on the browser as http://xxx.xxx.xxx.xxx/ and you can see the login interface of the web page
management.
Enter the user name and password and click the [logon] button to enter the settings screen.

2. Password Configuration
There are two levels of access: root level and general level. A user with root level access can
browse and set all configuration parameters, while a user with general level can set all configuration
parameters except server parameters for SIP.
 Default user with general level: The default is not set, are free to add.
 Default user with root level:
 User name: admin
 Password: admin

11 / 50
[键入文字]

3. Configuration via WEB

(1) System
a) Information

Information
Field Name Explanation
System Display equipment model, hardware version, software version, uptime, Last uptime and
Information MEMinfo.
Shows the configuration information for WAN port, including connection mode of WAN
Network
port (Static, DHCP, PPPoE), MAC address, IP address of WAN port.
SIP Accounts Shows the phone numbers and registration status for the 2 SIP LINES.

12 / 50
[键入文字]

b) Account
Through this page, user can add or remove users depends on their needs and can modify existing user
permission.

Account
Field Name Explanation
Change Web Authentication Password
You Can modify the login password to the account
Add New User
You can add new user
User Accounts
Show the existing user information

13 / 50
[键入文字]

c) Configurations

Configurations
Field Name Explanation
Export Save the equipment configuration to a txt or xml file. Please note to Right click on
Configurations the choice and then choose “Save Link As.”
Import
Browse to the config file, and press Update to load it to the equipment.
Configurations
Reset to factory
This will restore factory default and remove all configuration information.
defaults

d) Upgrade

Upgrade
Field Name Explanation
Software upgrade
Browse to the firmware, and press Update to load it to the equipment.

14 / 50
[键入文字]

e) Auto Provision

Auto Provision
Field Name Explanation
Common Settings
Show the current config file’s version. If the version of configuration downloaded
Current
is higher than this, the configuration will be upgraded. If the endpoints confirm
Configuration
the configuration by the Digest method, the configuration will not be upgraded
Version
unless it differs from the current configuration
Show the common config file’s version. If the configuration downloaded and this
General
configuration is the same, the auto provision will stop. If the endpoints confirm
Configuration
the configuration by the Digest method, the configuration will not be upgraded
Version
unless it differs from the current configuration.
CPE Serial Number Serial number of the equipment
Authentication Username for configuration server. Used for FTP/HTTP/HTTPS. If this is blank the
Name phone will use anonymous
Authentication
Password for configuration server. Used for FTP/HTTP/HTTPS.
Password
Configuration File
Encryption key for the configuration file
Encryption Key
General
Configuration File Encryption key for common configuration file
Encryption Key
Save Auto Provision Save the auto provision username and password in the phone until the server url
Information changes

15 / 50
[键入文字]

DHCP Option
The equipment supports configuration from Option 43, Option 66, or a Custom
Option Value
DHCP option. It may also be disabled.
Custom Option
Custom option number. Must be from 128 to 254.
Value
SIP Plug and Play (PnP)
If this is enabled, the equipment will send SIP SUBSCRIBE messages to a multicast
address when it boots up. Any SIP server understanding that message will reply
Enable SIP PnP
with a SIP NOTIFY message containing the Auto Provisioning Server URL where
the phones can request their configuration.
Server Address PnP Server Address
Server Port PnP Server Port
Transportation
PnP Transfer protocol – UDP or TCP
Protocol
Update Interval Interval time for querying PnP server. Default is 1 hour.
Static Provisioning Server
Set FTP/TFTP/HTTP server IP address for auto update. The address can be an IP
Server Address
address or Domain name with subdirectory.
Configuration File Specify configuration file name. The equipment will use its MAC ID as the config
Name file name if this is blank.
Protocol Type Specify the Protocol type FTP, TFTP or HTTP.
Update Interval Specify the update interval time. Default is 1 hour.
1. Disable – no update
Update Mode 2. Update after reboot – update only after reboot.
3. Update at time interval – update at periodic update interval
TR069
Enable TR069 Enable/Disable TR069 configuration
ACS Server Type Select Common or CTC ACS Server Type.
ACS Server URL ACS Server URL.
ACS User User name for ACS.
ACS Password ACS Password.
TR069 Auto Login Enable/Disable TR069 Auto Login.
INFORM Sending
Time between transmissions of “Inform” Unit is seconds.
Period

16 / 50
[键入文字]

f) Tools

Syslog is a protocol used to record log messages using a client/server mechanism. The Syslog server
receives the messages from clients, and classifies them based on priority and type. Then these messages
will be written into a log by rules which the administrator has configured.
There are 8 levels of debug information.
Level 0: emergency; System is unusable. This is the highest debug info level.
Level 1: alert; Action must be taken immediately.
Level 2: critical; System is probably working incorrectly.
Level 3: error; System may not work correctly.
Level 4: warning; System may work correctly but needs attention.
Level 5: notice; It is the normal but significant condition.
Level 6: Informational; It is the normal daily messages.
Level 7: debug; Debug messages normally used by system designer. This level can only be displayed
via telnet.

Tools
Field Name Explanation
Syslog
Enable Syslog Enable or disable system log.
Server Address System log server IP address.
Server Port System log server port.
APP Log Level Set the level of APP log.
SIP Log Level Set the level of SIP log.
Network Packets Capture
Capture a packet stream from the equipment. This is normally used to troubleshoot problems.

17 / 50
[键入文字]

Reboot Phone
Some configuration modifications require a reboot to become effective. Clicking the Reboot button will
lead to reboot immediately.
Note: Be sure to save the configuration before rebooting.

(2) Network
a) Basic

Field Name Explanation

Network Status
IP The current IP address of the equipment
Subnet mask The current Subnet Mask
Default gateway The current Gateway IP address
MAC The MAC address of the equipment
MAC Timestamp Get the MAC address of time.
Settings
Select the appropriate network mode. The equipment supports three network modes:
Network parameters must be entered manually and will not change. All parameters
Static IP
are provided by the ISP.
DHCP Network parameters are provided automatically by a DHCP server.
PPPoE Account and Password must be input manually. These are provided by your ISP.
If Static IP is chosen, the screen below will appear. Enter values provided by the ISP.
DNS Server
Select the Configured mode of the DNS Server.
Configured by

18 / 50
[键入文字]

Primary DNS
Enter the server address of the Primary DNS.
Server
Secondary DNS
Enter the server address of the Secondary DNS.
Server
After entering the new settings, click the APPLY button. The equipment will save the new settings and
apply them. If a new IP address was entered for the equipment, it must be used to login to the phone
after clicking the APPLY button.

b) Advanced
The equipment supports 802.1Q/P protocol and DiffServ configuration. VLAN function can support
the different VLAN ID mode of processing in the WAN port and LAN port.
 Chart 1 shows a network switch with no VLAN. Any broadcast frames will be transmitted to all other
ports. For example, frames broadcast from Port 1 will be sent to Ports 2, 3, and 4.

 Chart 2 shows an example with two VLANs indicated by red and blue. In this example, frames
broadcast from Port 1 will only go to Port 2 since Ports 3 and 4 are in a different VLAN. VLANs can be
used to divide a network by restricting the transmission of broadcast frames.

19 / 50
[键入文字]

Note: In practice, VLANs are distinguished by the use of VLAN IDs.

Advanced
Field Name Explanation
Link Layer Discovery Protocol (LLDP) Settings
Enable LLDP Enable or Disable Link Layer Discovery Protocol (LLDP)
Enables the telephone to synchronize its VLAN data with the Network
Enable Learning Switch. The telephone will automatically synchronize DSCP, 802.1p, and
Function VLAN ID values even if these values differ from those provided by the LLDP
server.
Packet Interval(1~3600) The time interval for sending LLDP Packets
VLAN Settings
Enable VLAN Enable or Disable WAN Port VLAN
VLAN ID Specify the value of the VLAN ID. Range is 0-4095
802.1p Signal Priority Specify the value of the signal 802.1p priority. Range is 0-7
802.1p Media Priority Specify the value of the voice 802.1p priority. Range is 0-7
Quality of Service (QoS) Settings
Enable DSCP QoS Enable or Disable Differentiated Services Code Point (DSCP)
Media QoS Priority Specify the value of the Media DSCP in decimal
Signal QoS Priority Specify the value of the Signal DSCP in decimal

20 / 50
[键入文字]

802.1X Settings

Enable 802.1X Enable or Disable 812.1X

Username 802.1X user account
Password 802.1X password
HTTPS Certification File
Upload or delete HTTPS Certification File

c) VPN
The device supports remote connection via VPN. It supports both Layer 2 Tunneling Protocol (L2TP)
and OpenVPN protocol. This allows users at remote locations on the public network to make secure
connections to local networks.

21 / 50
[键入文字]

Field Name Explanation

VPN IP Address Shows the current VPN IP address.
VPN Mode
Enable VPN Enable/Disable VPN.
L2TP Select Layer 2 Tunneling Protocol
Select OpenVPN Protocol. (Only one protocol may be activated. After the selection
OpenVPN
is made, the configuration should be saved and the phone be rebooted.)
Layer 2 Tunneling Protocol (L2TP)
L2TP Server
Set VPN L2TP Server IP address.
Address
Authentication
Set User Name access to VPN L2TP Server.
Name
Authentication
Set Password access to VPN L2TP Server.
Password
Open VPN Files
Upload or delete Open VPN Certification Files

22 / 50
[键入文字]

(3) Line
a) SIP
Configure a SIP server on this page.

23 / 50
[键入文字]

SIP
Field Name Explanation
Basic Settings (Choose the SIP line to configured)
Display the current line status at page loading. To get the up to date line status,
Line Status
user has to refresh the page manually.
Username Enter the username of the service account.
Display name Enter the display name to be sent in a call request.
Authentication Name Enter the authentication name of the service account
Authentication
Enter the authentication password of the service account
Password
Activate Whether the service of the line should be activated
SIP Proxy Server
Enter the IP or FQDN address of the SIP proxy server
Address

24 / 50
[键入文字]

SIP Proxy Server Port Enter the SIP proxy server port, default is 5060
Outbound proxy Enter the IP or FQDN address of outbound proxy server provided by the service
address provider
Outbound proxy port Enter the outbound proxy port, default is 5060
Realm Enter the SIP domain if requested by the service provider
Codecs Settings
Set the priority and availability of the codecs by adding or remove them from the list.
Advanced Settings
Call Forward Enable unconditional call forward, all incoming calls will be forwarded to the
Unconditional number specified in the next field
Call Forward Number
Set the number of unconditional call forward
for Unconditional
Enable call forward on busy, when the phone is busy, any incoming call will be
Call Forward on Busy
forwarded to the number specified in the next field
Call Forward Number
Set the number of call forward on busy
for Busy
Enable call forward on no answer, when an incoming call is not answered
Call Forward on No
within the configured delay time, the call will be forwarded to the number
Answer
specified in the next field
Call Forward Number
Set the number of call forward on no answer
for No Answer
Call Forward Delay for
Set the delay time of not answered call before being forwarded
No Answer
Hotline Delay Set the delay for hotline before the system automatically dialed it
Enable auto-answering, the incoming calls will be answered automatically after
Enable Auto Answering
the delay time
Auto Answering Delay Set the delay for incoming call before the system automatically answered it
Enable the device to subscribe a voice message waiting notification, if enabled,
Subscribe For Voice
the device will receive notification from the server if there is voice message
Message
waiting on the server
Voice Message Number Set the number for retrieving voice message
Voice Message
Set the interval of voice message notification subscription
Subscribe Period
Enable hotline configuration, the device will dial to the specific number
Enable Hotline immediately at audio channel opened by off-hook handset or turn on
hands-free speaker or headphone
Hotline Number Set the hotline dialing number

25 / 50
[键入文字]

Enable Do-not-disturb, any incoming call to this line will be rejected

Enable DND
automatically
Blocking Anonymous
Reject any incoming call without presenting caller ID
Call
Use 182 Response for
Set the device to use 182 response code at call waiting response
Call waiting
Anonymous Call
Set the standard to be used for anonymous
Standard
Dial Without Registered Set call out by proxy without registration
Click To Talk Set Click To Talk
User Agent Set the user agent, the default is Model with Software Version.
Use Quote in Display
Whether to add quote in display name
Name
Ring Type Set the ring tone type for the line
Set the type of call conference, Local=set up call conference by the device
Conference Type itself, maximum supports two remote parties, Server=set up call conference by
dialing to a conference room on the server
Server Conference
Set the conference room number when conference type is set to be Server
Number
Transfer Timeout Set the timeout of call transfer process
Enable Long Contact Allow more parameters in contact field per RFC 3840
Enable Missed Call Log If enabled, the phone will save missed calls into the call history record.
If setting enabled, the device will use single codec in response to an incoming
Response Single Codec
call request
When this setting is enabled, the features in this section will not be handled by
the device itself but by the server instead. In order to control the enabling of
Use Feature Code
the features, the device will send feature code to the server by dialing the
number specified in each feature code field.
Specific Server Type Set the line to collaborate with specific server type
Registration Expiration Set the SIP expiration interval
Use VPN Set the line to use VPN restrict route
Use STUN Set the line to use STUN for NAT traversal
Convert URI Convert not digit and alphabet characters to %hh hex code
DTMF Type Set the DTMF type to be used for the line
DTMF SIP INFO Mode Set the SIP INFO mode to send ‘*’ and ‘#’ or ‘10’ and ‘11’
Transportation Protocol Set the line to use TCP or UDP for SIP transmission
SIP Version Set the SIP version

26 / 50
[键入文字]

Caller ID Header Set the Caller ID Header

Enables the use of strict routing. When the phone receives packets from the
Enable Strict Proxy
server, it will use the source IP address, not the address in via field.
Enable user=phone Sets user=phone in SIP messages.
Enable SCA Enable/Disable SCA (Shared Call Appearance )
Enable BLF List Enable/Disable BLF List
Set the line to use DNS SRV which will resolve the FQDN in proxy server into a
Enable DNS SRV
service list
Set the line to use dummy UDP or SIP OPTION packet to keep NAT pinhole
Keep Alive Type
opened
Keep Alive Interval Set the keep alive packet transmitting interval
Set the line to enable call ending by session timer refreshment. The call session
Enable Session Timer will be ended if there is not new session timer event update received after the
timeout period
Session Timeout Set the session timer timeout period
Enable Rport Set the line to add rport in SIP headers
Enable PRACK Set the line to support PRACK SIP message
Keep Authentication Keep the authentication parameters from previous authentication
Using TCP protocol to guarantee usability of transport for SIP messages above
Auto TCP
1500 bytes
Enable Feature Sync Feature Sycn with server
Enable GRUU Support Globally Routable User-Agent URI (GRUU)
The registered server will receive the subscription package from ordinary
application of BLF phone.
BLF Server
Please enter the BLF server, if the sever does not support subscription package,
the registered server and subscription server will be separated.
BLF List allows one BLF key to monitor the status of a group. Multiple BLF lists
BLF List Number
are supported.
SIP Encryption Enable SIP encryption such that SIP transmission will be encrypted
SIP Encryption Key Set the pass phrase for SIP encryption
RTP Encryption Enable RTP encryption such that RTP transmission will be encrypted
RTP Encryption Key Set the pass phrase for RTP encryption

27 / 50
[键入文字]

b) Basic Settings
STUN – Simple Traversal of UDP through NAT –A STUN server allows a phone in a private network to
know its public IP and port as well as the type of NAT being used. The equipment can then use this
information to register itself to a SIP server so that it can make and receive calls while in a private
network.

Basic Settings
Field Name Explanation
SIP Settings
Local SIP Port Set the local SIP port used to send/receive SIP messages.
Registration Failure
Set the retry interval of SIP REGISTRATION when registration failed.
Retry Interval
STUN Settings
Server Address STUN Server IP address

28 / 50
[键入文字]

Server Port STUN Server Port – Default is 3478.

STUN blinding period – STUN packets are sent at this interval to keep the NAT
Binding Period
mapping active.
SIP Waiting Time Waiting time for SIP. This will vary depending on the network.
SIP Line Using STUN(SIP1 or SIP2)
Use STUN Enable/Disable STUN on the selected line.
TLS Certification File
Upload or delete the TLS certification file used for encrypted SIP transmission.
Note: the SIP STUN is used to achieve the SIP penetration of NAT, is the realization of a service, when the
equipment configuration of the STUN server IP and port (usually the default is 3478), and select the Use
Stun SIP server, the use of NAT equipment to achieve penetration.

(4) EGS Setting

a) Features

29 / 50
[键入文字]

Features
Field Name Explanation
Common Settings
DND might be disabled phone for all SIP lines, or line for SIP individually. But
Enable DND
the outgoing calls will not be affected
Ban Outgoing If enabled, no outgoing calls can be made.
Enable Intercom Mute If enabled, mutes incoming calls during an intercom call.
Enable Intercom
If enabled, plays intercom ring tone to alert to an intercom call.
Ringing
Enable Auto Dial Out Enable Auto Dial Out
Auto Dial Out Time Set Auto Dial Out Time
Enable Auto Answer Enable Auto Answer function
Auto Answer Timeout Set Auto Answer Timeout
No Answer Auto
Enable automatically hang up when no answer
Hangup
Auto Hangup Timeout Configuration in a set time, automatically hang up when no answer
Dial Fixed Length to
Enable or disable dial fixed length to send.
Send
The number will be sent to the server after the specified numbers of digits are
Send length
dialed.
Enable Speed Dial
Enable Speed Dial Hand Up function
Hangup
Use Function Key to
Configure whether to enable the function keys, is disabled by default.
Answer
Dial Number Voice Play Configuration Open / Close Dial Number Voice Play
Voice Play Language Set language of the voice prompt
Set ID card stats:
Normal: This is the work mode, after the slot card can to open the door.
Card Reader Working
Card Issuing: This is the issuing mode, after the slot card can to add ID cards.
Mode
Card Revoking: This is the revoking mode, after the slot card can to delete ID
cards.

30 / 50
[键入文字]

Field Name Explanation

Advanced Settings
Monostable: there is only one fixed action status for door unlocking.
Bistable: there are two actions and statuses, door unlocking and door locking.
Switch Mode Each action might be triggered and changed to the other status. After
changed, the status would be kept.
Initial Value is Monostable
Password+dialing: password input is default. Dialing mode is as below if you
want.
Keypad Mode Only password: password input only, dialing would be forbidden.
Only dialing: dial input only, * Key to enter the dial, the # key to hang up.
Initial Value is Password and dialing.
Door unlocking time for Monostable mode only. If the time is up, the door
Switch-On Duration
would be locked automatically. Initial Value is 5 seconds.
Talk Duration The call will be ended automatically when time up. Initial Value is 120 seconds
Remote Password Remote door unlocking password. Initial Value is “*”.
Local door unlocking password via keypad, the default password length is 4.
Local password
Initial Value is “6789”.
Device description displayed on IP scanning tool software. Initial Value is “i20S
Description
IP Door Phone”.
Enable Access Table: enter <Access Code> for opening door during calls.
Enable Access Table Disable Access Table: enter <Remote Password> for opening door during calls.
Default Enable.
<Primary /Secondary>mode allow system to call primary extension first, if
there were no answer, it would cancel the call and then call secondary
Hot Key Dial Mode extension automatically.
Select <Day/Night>mode allow system to check the calling time is belong to Day or
Night time, and then decide to call the number 1 or number 2 automatically.
Users just press speed dial key once.
The period between hot key dialing to the first and second number. Initial
Call Switched Time
Value is 16 seconds.
Day Start Time The start time of the Day When you select<Day/Night>mode.
Day End Time The end time of the day When you select <Day/Night>mode.
Address of Open Log
Log server address(IP or domain name)
Server
Port of Open Log
Log server port (0-65535) , Initial Value is 514.
Server

31 / 50
[键入文字]

Enable Open Log

Enable or disable to connect with log server
Server
Enable Indoor Open Enable or disable to use indoor switch to unlock the door.
Enable Card Reader Enable or disable card reader for RFID cards.
Limit Talk Duration If enabled, calls would be forced ended after talking time is up.
Indication tone for door unlocked. There are 3 type of tone: silent/short
Door Unlock Indication
beeps/long beeps.
The remote access code length would be restricted with it. If the input access
Remote Code Check
code length is matched with it, system would check it immediately. Initial
Length
Value is 4.
Block Out Settings
Add or Delete Blocked numbers – Enter the prefix of numbers which should not be dialed by the phone.
For example, if 001 is entered, the phone will not dial any numbers beginning with 001.
X and x are wildcards which match single digits. For example, if 4xxx or 4XXX is entered, the phone will
not dial any 4 digit numbers beginning with 4. It will dial numbers beginning with 4 which are longer or
shorter than 4 digits.

b) Audio
This page configures audio parameters such as voice codec, speak volume, mic volume and ringer
volume.

Audio Setting
Field Name Explanation
First Codec The first codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB
Second Codec The second codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB, None
Third Codec The third codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB, None

32 / 50
[键入文字]

Fourth Codec The forth codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB, None
DTMF Payload Type The RTP Payload type that indicates DTMF. Default is 101
Default Ring Type Ring Sound – There are 9 standard types and 3 User types.
G.729AB Payload
G.729AB Payload Length – Adjusts from 10 – 60 mSec.
Length
Tone Standard Configure tone standard area.
G.722 Timestamps Choices are 160/20ms or 320/20ms.
G.723.1 Bit Rate Choices are 5.3kb/s or 6.3kb/s.
Speakerphone
Set the speaker calls the volume level.
Volume
MIC Input Volume Set the MIC calls the volume level.
Broadcast Output
Set the broadcast the output volume level.
Volume
Signal Tone Volume Set the audio signal the output volume level.
Enable or disable Voice Activity Detection (VAD). If VAD is enabled, G729 Payload
Enable VAD
length cannot be set greater than 20 mSec.

c) MCAST

It is easy and convenient to use multicast function to send notice to each member of the multicast via
setting the multicast key on the device and sending multicast RTP stream to pre-configured multicast
address. By configuring monitoring multicast address on the device, monitor and play the RTP stream
which sent by the multicast address.

33 / 50
[键入文字]

MCAST Settings
Equipment can be set up to monitor up to 10 different multicast addresses, used to receive the
multicast RTP stream sent by the multicast address.
Here are the ways to change equipment receiving multicast RTP stream processing mode in the Web
interface: set the ordinary priority and enable page priority.
 Priority:
In the drop-down box to choose priority of ordinary calls the priority, if the priority of the incoming
flows of multicast RTP, lower precedence than the current common calls, device will automatically ignore
the group RTP stream. If the priority of the incoming flow of multicast RTP is higher than the current
common calls priority, device will automatically receive the group RTP stream, and keep the current
common calls in state. You can also choose to disable in the receiving threshold drop-down box, the
device will automatically ignore all local network multicast RTP stream.

 The options are as follows:

 1-10: To definite the priority of the common calls, 1 is the top level while 10 is the lowest
 Disable: ignore all incoming multicast RTP stream
 Enable the page priority:
Page priority determines the device how to deal with the new receiving multicast RTP stream
when it is in multicast session currently. When Page priority switch is enabled, the device will
automatically ignore the low priority multicast RTP stream but receive top-level priority multicast RTP
stream, and keep the current multicast session in state; If it is not enabled, the device will
automatically ignore all receiving multicast RTP stream.

 Web Settings:

The multicast SS priority is higher than that of EE, which is the highest priority.
Note: when pressing the multicast key for multicast session, both multicast sender and receiver will
beep.

34 / 50
[键入文字]

Listener configuration

 Blue part (name)

"Group 1","Group 2" and "Group 3" are your setting monitoring multicast name.The group name will
be displayed on the screen when you answer the multicast. If you have not set, the screen will display the
IP: port directly.
 Purple part (host: port)
It is a set of addresses and ports to listen, separated by a colon.
 Pink part (index / priority)
Multicast is a sign of listening, but also the monitoring multicast priority. The smaller number refers to
higher priority.
 Red part (priority)
It is the general call, non multicast call priority. The smaller number refers to high priority. The
followings will explain how to use this option:
 The purpose of setting monitoring multicast "Group 1" or "Group 2" or "Group 3" launched a multicast
call.
 All equipment has one or more common non multicast communication.
 When you set the Priority for the disable, multicast any level will not answer, multicast call is rejected.
 when you set the Priority to a value, only higher than the priority of multicast can come in, if you set
the Priority is 3, group 2 and group 3 for priority level equal to 3 and less than 3 were rejected, 1
priority is 2 higher than ordinary call priority device can answer the multicast message at the same
time, keep the hold the other call.
 Green part (Enable Page priority)
Set whether to open more priority is the priority of multicast, multicast is pink part number. Explain
how to use:
 The purpose of setting monitoring multicast "group 1" or "3" set up listening "group of 1" or "3"
multicast address multicast call.
 All equipment has been a path or multi-path multicast phone, such as listening to "multicast
information group 2".

35 / 50
[键入文字]

 If multicast is a new "group of 1", because "the priority group 1" is 2, higher than the current call
"priority group 2" 3, so multicast call will can come in.
 If multicast is a new "group of 3", because "the priority group 3" is 4, lower than the current call
"priority group 2" 3, "1" will listen to the equipment and maintain the "group of 2".

Multicast service
 Send: when configured ok, our key press shell on the corresponding equipment, equipment directly
into the Talking interface, the premise is to ensure no current multicast call and 3-way of the case, the
multicast can be established.
 Lmonitor: IP port and priority configuration monitoring device, when the call is initiated and incoming
multicast, directly into the Talking interface equipment.

d) Action URL

Action URL Event Settings

URL for various actions performed by the phone. These actions are recorded and sent as xml files to the
server. Sample format is http://InternalServer /FileName.xml

36 / 50
[键入文字]

e) Time/Date

Time/Date
Field Name Explanation
Network Time Server Settings
Time Synchronized via
Enable time-sync through SNTP protocol
SNTP
Time Synchronized via
Enable time-sync through DHCP protocol
DHCP
Primary Time Server Set primary time server address
Secondary Time Set secondary time server address, when primary server is not reachable, the device
Server will try to connect to secondary time server to get time synchronization.
Time zone Select the time zone
Resync Period Time of re-synchronization with time server
Date Format
12-hour clock Set the time display in 12-hour mode

37 / 50
[键入文字]

Date Format Select the time/date display format

Daylight Saving Time Settings
Location Select the user's time zone specific area
Select automatic DST according to the preset rules of DST, or the manually input
DST Set Type
rules
Offset The DST offset time
Month Start The DST start month
Week Start The DST start week
Weekday Start The DST start weekday
Hour Start The DST start hour
Month End The DST end month
Week End The DST end week
Weekday End The DST end weekday
Hour End The DST end hour
Manual Time Settings
The time set by hand, need to disable SNTP service first.

(5) EGS Cards

a) EGS Cards

EGS Cards
Field Name Explanation
Import Door Card Table
Click the <Browse> to choose to import door card list file (doorCard.csv), click <Update> can be batch
import.

38 / 50
[键入文字]

Door Card Table

Add Door Card The input RFID card numbers the top 10, for example, 0004111806, click <add>.
Click here to Save Right-click it and select save target to your
Door Card Table computer.
Name The name of has been issuer cards.
The card number of has been issuer cards.
ID (Note: The card is not registered in the remote access list is unable to open the
door.)
Issuing Date The issuing date of has been issuer cards.
Card State To have been issuer cards the state.
Delete Click <Delete>, will delete the door card list within the selected ID cards.
Delete All Click <Delete All>, to delete all door card lists.
Administrator Table
The input RFID card numbers the top 10, for example, 0004111806, select admin
Add Admin Card
card the type, click <add>.
Type: Issuer and Revoking.
Entrance guard in normal state, brush card(issuing card) entrance guard into the issuing state, and then
brush to add a card, the card is added to the database, add swipe again after card(issuing card) entrance
guard returned to normal. Delete card operation and issuing card the same.
Can release at most 10 cards, 500 copies of ordinary cards.
Note: in the issuing state to delete brush card is invalid, and vice versa.
The show admin card the ID, Date and Type.
Delete Click <Delete>, will delete the admin card list within the selected ID cards.
All Delete Click <Delete All>, to delete all admin card lists.

39 / 50
[键入文字]

b) EGS ACCESS

Field Name Explanation

Import Access Table
Click the <Browse> to choose to import remote access list file (access List.csv) and then click <Update>
can be batch import remote access rule.
Access Table
According to entrance guard access rules have been added, can choose single or multiple rules on this list
to delete operation.
Add Access Rule
Name User name
ID RFID card number
Department Card holder's department
Position Card holder's position
1/ When the door phone has been answering the call from below <Phone Num> user,
then the <Phone Num> user can input the access code by keypad to unlock the door
Access Code
remotely.
2/ The user’s private password for local door unlocking by door phone’s keypad.

40 / 50
[键入文字]

Access Code
Select Access Code Action mode
Action
When enabled, private password inputting and RFID reading must be matched
Double Auth
simultaneously for door unlocking.
Host: the door phone would answer all call automatically.
Type Guest: the door phone would be ringing for incoming call, if the auto answer had been
disabled.
Valid for user access rules (including RFID, access code, etc) within corresponding time
Profile
section. If NONE is selected, it would be taken effect all day.
Virtual extension number, used to make position call instead of real number.
Location
It might be taken with unit number, or room number.
Number User Phone Number
Fwd Number Call forwarding number when above Phone Num is unavailable.
Profile Setting
Profile There are 4 sections for time profile configuration
Profile Name The name of profile to help administrator to remember the time definition
If it were yes, the time profile would be taken effect. Other time section not included in
Statue
the profiles would not allow users to open door
Start Time The start time of section
End Time The end time of section

(6) EGS Logs

According to open event log, can record up to 1.5 w open event, after more than cover the old
records. Right click on the links to select save target as the door log can export CSV
format.

41 / 50
[键入文字]

Field Name Explanation

Door Open Log
Result Show the results of the open the door (Success or Failed)
Time Open the door of time.
Duration Duration of open the door.
Access Name If is the open the door for slot card or remote, will display remote access the name.
1. If open the door way to brush card shows card number
2. If the door way to open the door for the remote display the phone number of the
Access ID
door.
3. If open the door way to open the door for local, no display information.
Open type: 1. local, 2. Remote, 3. Brush card (Temporary Card, Valid Card and Illegal
Card).
Note: there are three kinds of credit card feedback results.
Type
1. Temporary Card (Only add the card number, without adding other rules )
2. Valid Card (Has been added access rules)
3. Illegal Card (Did not add information)

(7) Function Key

a) Function Key Settings

42 / 50
[键入文字]

 Key Event
Set the key type to the Key Event.

Type Subtype Usage

None Not responding
Dial Dial function
Key Event Release Delete password input, Cancel dial input and End calls
OK Identify key
Handfree The hand-free key(with hook dial, hang up)

 Hot Key
Enter the phone number in the input box, when you press the shortcut key, equipment will dial set
telephone number. This button can also be used to set the IP address, press the shortcut key IP direct dial
call.

Type Number Line Subtype Usage

In Speed dial mode, with
Fill the can define
The SIP Speed Dial
called whether this call is allowed to be hang up by
account
Hot Key party’s SIP re-press the speed dial
correspondi
account or In Intercom mode, if the caller’s IP phone
ng lines
address Intercom support intercom feature, can realize auto
answer

43 / 50
[键入文字]

 Multicast
Multicast function is launched will voice messages sent to set the multicast address, all equipment to
monitor the group multicast address can receive sponsors speech information, etc. Using multicast
functionality can be simple and convenient to send notice to each member in the multicast.
Through the DSS Key configuration multicast calling WEB is as follows:

Type Number Subtype Usage

G.711A
Narrowband speech coding (4Khz)
Set the host IP address and G.711U
port number, the middle G.722 Wideband speech coding (7Khz)
Multicast
separated by a colon G.723.1
G.726-32 Narrowband speech coding (4Khz)
G.729AB

 operation mechanism
Device through the DSS Key configuration of multicast address and port and started coding; set by
WEB to monitor the multicast address and port; device sends a multicast, listens to the address of the
device can receive the multicast content.
 calling configuration
The call is already exists, and three party or initiated multicast communication, so it will not be able
to launch a new multicast call.

44 / 50
[键入文字]

V. Appendix
1. Technical parameters
Communication protocol SIP 2.0(RFC-3261)
Main chipset Broadcom
DSS Key 1(Stainless steel)
Keys
Numeric keyboard Support
MIC 1个
Speaker 3W/4Ω
Audio
Volume control Adjustable
Full duplex speakerphone Support (AEC)
Speech Protocols RTP
flow Decoding G.729、G.723、G.711、G.722、G.726
Active Switched Output 12V/700mA DC
Ports
WAN 10/100BASE-TX s Auto-MDIX, RJ-45
EM4100 (125Khz) ---Standard configuration
RFID/IC card reader(relay)
MIFARE One(13.56Mhz) ---Custom-made
Power supply mode 12V / 1A DC or PoE
PoE PoE 802.3af (Class 3 - 6.49~12.95W)
Cables CAT5 or better
Shell Material Metal panel, ABS face-piece and back shell
Working temperature -10°C to 60°C
Working humidity 10% - 90%
Storage temperature -40°C to 70°C
Installation way Wall mounted
External size 160 x 93 x 35mm
Package size 178 x 104 x 55mm
Gross weight 420g

45 / 50
[键入文字]

2. Basic functions
 2 SIP Lines
 PoE Enabled
 Full-duplex speakerphone (HF)
 Numeric keypad (Dial pad or Password input)
 Intelligent DSS Keys (Speed Dial/intercom etc)
 Wall mounted
 Integrated RFID Card reader
 1 indoor switch interface
 1 electric lock relay
 External power supply
 Door phone: call, password, RFID card, indoor switch
 Protection level: IP54，CE/FCC

3. Schematic diagram

MIC

RFID area
Lock status
Call and Ring status Numeric keypad
Network and (password or dialing)
Registration status

DSS key with LED

Speaker

46 / 50
[键入文字]

VI. Other instructions

1. Open door modes
 Local control
1) Local Password
 Set <Local Password> (the password is "6789" by default) via DOOR PHONE\DOOR PHONE as
above.
 Input password via keypad and press the "#" key, then the door will be unlocked.
2) Private access code
 Set <Add Access Rule\Access Code> and enable local authentication.
 Input access code via keypad and press the "#" key, then the door will be unlocked.
 Remote control
1) Visitors call the owner
 Visitors can call the owner via position speed dial or phone number. (After setting the speed dial
key, visitors can press it to call direct.)
 The owner answers the call and presses the "*" key to unlock the door for visitors.
2) Owner calls visitors
 Owner calls visitors via SIP phone.
 SIP door phone answers the call automatically.
 Owner inputs corresponding <Access codes> via SIP phone keypad to unlock the door.
 Swiping cards
 Use pre-assigned RFID cards to unlock the door, by touching RFID area of the device.
 Indoor switch
 Press indoor switch, which is installed and connected with the device, to unlock the door.

47 / 50
[键入文字]

2. Management of card
1) Administrator Table
<Issuer> and <Revocation>

 Add Administrator cards

Input a card’s ID, selected <Issuer> or <Revocation> in the types and Clicked <Add>, you can add
administrator card.

 Delete Administrator cards

Select the admin card of need to delete, click <Delete>.

2) Add user cards

 Method 1: used to add cards for starters typically
 In web page < EGS Setting →Features →Card Reader Working Mode > option, select <Card Issuing>.

 Click <Apply>, Card Reader would be entered the issuing status.

 Use new card to touch card reader induction area, and then you might hear the confirmed indication
tone from the device. Repeat step can to add more cards.

48 / 50
[键入文字]

 In web page < EGS Setting →Features →Card Reader Working Mode > option, select <Normal>.

 Click <Apply>, Card Reader would be back to the Normal status.

 The issuing records can be found from the door card table list.

 Methods 2: used to add cards for professionals

 Use <Issuer admin card> to touch card reader induction area, and it would be entered issuing card
status.
 Use new card to touch card reader induction area, and you might hear the confirmed indication tone
from the device. Repeat step 2 to add more cards.
 Use <Issuer admin card> to touch card reader induction area again, it would be back to normal
working status.

 Method 3: use to add few cards

 Input cards number in door card settings page, and then click <Add>.

Note: you can also use the USB card reader connected with PC to get cards ID automatically.

Only need to input the top 10 numbers.

49 / 50
[键入文字]

3) Delete user cards

 Method 1: used to batch delete cards for starters.
 In web page < EGS Setting →Features →Card Reader Working Mode > option, select <Card
Revoking>.

 Click <Apply>, Card Reader would be entered the revoking status.

 Use card to touch card reader induction area, and you might hear the card reader confirmed
indication tone. Repeat step can to delete more cards.
 In web page <EGS Setting →Features →Card Reader Working Mode >option, select <Normal>.

 Click <Apply>, Card Reader would be back to the Normal status.

 Method 2: used to batch add cards for intermediates.

 Use < Revocation admin card> to touch card reader induction area, and it would be entered revoking
card status.
 Use the cards you want to delete from system, to touch card reader induction area, and you might
hear the card reader confirmed indication tone. Repeat step 2 to delete cards.
 Use <Revocation admin card> to touch card reader induction area, and it would be back to card read
only status.

 Method 3: use to bulk delete or partially delete card records

 In web page<EGS Cards →Door Card Table>select the card ID and then click <Delete>.
Note: If you click <Delete All>, system will delete all the ID card records.

50 / 50