Lab - Configure Route Redistribution Within the Same Interior

Gateway Protocol (Instructor Version)

Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only.

Topology

Addressing Table
Device Interface IP Address Subnet Mask

R1 G0/0/0 10.1.12.1 255.255.255.0

R1
G0/0/1 10.1.11.1 255.255.255.0

R1
Loopback 0 10.1.1.1 255.255.255.0
R2 G0/0/0 10.1.12.2 255.255.255.0

R2
G0/0/1 10.1.23.2 255.255.255.0
R3 G0/0/0 10.1.23.3 255.255.255.0

R3
G0/0/1 10.1.32.1 255.255.255.0

R3
Loopback 0 10.3.3.3 255.255.255.0

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

Device Interface IP Address Subnet Mask

D1 G1/0/11 10.1.11.2 255.255.255.0

D1
Loopback 0 198.51.100.1 255.255.255.128
D2 G1/0/11 10.1.32.2 255.255.255.0

D2
Loopback 0 209.165.201.1 255.255.255.128

Objectives
Part 1: Build the Network and Configure Basic Device Settings
Part 2: Configure and Verify Two-Way Redistribution on R1
Part 3: Configure and Verify Two-Way Redistribution on R3
Part 4: Filter and Verify Redistribution using a Distribute List and Prefix List

Background / Scenario
Redistribution always includes two routing protocols: a source protocol and a destination protocol. The source
protocol provides the network prefixes that are to be redistributed. The destination protocol receives the
source protocol network prefixes. The redistribution configuration exists under the destination protocol.
Examples of source protocols are static, connected, RIP, EIGRP, OSPF, IS-IS, and BGP.
Routes can be redistributed between different routing protocols or between different processes of the same
routing protocol.
In this lab, you will configure mutual or two-way redistribution between multiple EIGRP processes. R1 is
running classic mode EIGRP for AS 64512 and EIGRP named mode for AS 64513. R3 is running EIGRP
named mode for AS 64513 and classic mode EIGRP for AS 64514.
Note: This lab is an exercise in configuring and verifying two-way route redistribution on routers R1 and R3.
Route redistribution in this lab does not reflect networking best practices.
Note: The routers used with CCNP hands-on labs are Cisco 4221s with Cisco IOS XE Release 16.9.4
(universalk9 image). The switches used in the labs are Cisco Catalyst 3650s with Cisco IOS XE Release
16.9.4 (universalk9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the
model and Cisco IOS version, the commands available and the output produced might vary from what is
shown in the labs.
Note: Make sure that all the devices have been erased and have no startup configurations. If you are unsure,
contact your instructor.
Instructor Note: Refer to the Instructor Lab Manual for the procedures to initialize and reload devices.

Required Resources
 3 Routers (Cisco 4221 with Cisco IOS XE Release 16.9.4 universal image or comparable)
 2 Switches (Cisco 3650 with Cisco IOS XE release 16.9.4 universal image or comparable)

 1 PC (Choice of operating system with terminal emulation program installed)

 Console cables to configure the Cisco IOS devices via the console ports
 Ethernet cables as shown in the topology

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

Instructions

Part 1: Build the Network and Configure Basic Device Settings

In Part 1, you will set up the network topology and configure basic settings.

Step 1: Cable the network as shown in the topology.

Attach the devices as shown in the topology diagram, and cable as necessary.

Step 2: Configure basic settings for each device.

a. Console into each device, enter global configuration mode, and apply the basic settings for the lab. Initial
configurations for each device are listed below.
Open configuration window

Router R1
hostname R1
no ip domain lookup
banner motd # R1, Configure Route Redistribution Within the Same Interior
Gateway Protocol #
line con 0
exec-timeout 0 0
logging synchronous
exit
interface g0/0/0
ip address 10.1.12.1 255.255.255.0
no shutdown
exit
interface g0/0/1
ip address 10.1.11.1 255.255.255.0
no shutdown
exit
interface loopback 0
ip address 10.1.1.1 255.255.255.0
no shutdown
exit
router eigrp 64512
eigrp router-id 1.1.1.1
network 10.1.11.0 0.0.0.255
exit
router eigrp CISCO
address-family ipv4 unicast autonomous-system 64513
eigrp router-id 1.1.1.1
network 10.1.1.0 0.0.0.255
network 10.1.12.0 0.0.0.255
exit
end

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

Router R2
hostname R2
no ip domain lookup
banner motd # R2, Configure Route Redistribution Within the Same Interior
Gateway Protocol #
line con 0
exec-timeout 0 0
logging synchronous
exit
interface g0/0/0
ip address 10.1.12.2 255.255.255.0
no shutdown
exit
interface g0/0/1
ip address 10.1.23.2 255.255.255.0
no shutdown
exit
router eigrp CISCO
address-family ipv4 unicast autonomous-system 64513
eigrp router-id 2.2.2.2
network 10.1.12.0 0.0.0.255
network 10.1.23.0 0.0.0.255
end
Router R3
hostname R3
no ip domain lookup
banner motd # R3, Configure Route Redistribution Within the Same Interior
Gateway Protocol #
line con 0
exec-timeout 0 0
logging synchronous
exit
interface g0/0/0
ip address 10.1.23.1 255.255.255.0
no shutdown
exit
interface g0/0/1
ip address 10.1.32.1 255.255.255.0
no shutdown
exit
interface loopback 0
ip address 10.3.3.1 255.255.255.0
no shutdown
exit
router eigrp 64514

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

eigrp router-id 3.3.3.3

network 10.1.32.0 0.0.0.255
exit
router eigrp CISCO
address-family ipv4 unicast autonomous-system 64513
eigrp router-id 3.3.3.3
network 10.1.23.0 0.0.0.255
network 10.3.3.0 0.0.0.255
exit
end
Switch D1
hostname D1
no ip domain lookup
ip routing
banner motd # D1, Configure Route Redistribution Within the Same Interior
Gateway Protocol #
line con 0
exec-timeout 0 0
logging synchronous
exit
interface range g1/0/1-24
shutdown
exit
interface g1/0/11
no switchport
ip address 10.1.11.2 255.255.255.0
no shutdown
exit
interface loopback 0
ip address 198.51.100.1 255.255.255.128
no shutdown
exit
router eigrp 64512
eigrp router-id 11.11.11.11
network 10.1.11.0 0.0.0.255
network 198.51.100.0 0.0.0.127
end
Switch D2
hostname D2
no ip domain lookup
ip routing
banner motd # D2, Configure Route Redistribution Within the Same Interior
Gateway Protocol #
line con 0
exec-timeout 0 0

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

logging synchronous
exit
interface range g1/0/1-24
shutdown
exit
interface g1/0/11
no switchport
ip address 10.1.32.2 255.255.255.0
no shutdown
exit
interface loopback 0
ip address 209.165.201.1 255.255.255.128
no shutdown
exit
router eigrp 64514
eigrp router-id 22.22.22.22
network 10.1.32.0 0.0.0.255
redistribute static
eigrp stub static
exit
ip route 0.0.0.0 0.0.0.0 Loopback0
end
b. Set the clock on all devices to UTC time.
c. Save the running configuration to startup-config on all devices.
Close configuration window

Step 3: Verify EIGRP neighborships on R1.

a. Verify that R1 has two EIGRP neighbor relationships. One EIGRP neighbor is from named mode AS
64513. The other neighbor is from EIGRP classic mode AS 64512.
Open configuration window

R1# show ip eigrp neighbors

EIGRP-IPv4 Neighbors for AS(64512)
H Address Interface Hold Uptime SRTT RTO QSeq
(sec) (ms) CntNum
0 10.1.11.2 Gi0/0/1 10 00:02:10 3 100 02
EIGRP-IPv4 VR(CISCO) Address-Family Neighbors for AS(64513)
H Address Interface Hold Uptime SRTT RTO QSeq
(sec) (ms) CntNum
0 10.1.12.2 Gi0/0/0 11 00:03:38 2 100 07

b. Next, verify that R1 has learned internal routes form each EIGRP neighbor. Issue the show ip route
eigrp command for AS 64512, as shown. Notice the gateway of last resort is not set and the internal
EIGRP route is from D1 Loopback 0.
R1# show ip route eigrp 64512 | begin Gateway
Gateway of last resort is not set
198.51.100.0/25 is subnetted, 1 subnets
D 198.51.100.0
[90/130816] via 10.1.11.2, 04:24:45, GigabitEthernet0/0/1
Close configuration window

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

c. Issue the show ip route eigrp command for EIGRP named mode, as shown. Notice the gateway of last
Open configuration window
resort is not set and the internal EIGRP routes are from R1 and R3.
R2# show ip route eigrp 64513 | begin Gateway
Gateway of last resort is not set
10.0.0.0/8 is variably subnetted, 6 subnets, 2 masks
D 10.1.1.0/24 [90/10880] via 10.1.12.1, 00:10:57, GigabitEthernet0/0/0
D 10.3.3.0/24 [90/10880] via 10.1.23.1, 00:00:21, GigabitEthernet0/0/1
Close configuration window

d. Verify that R3 has two EIGRP neighbor relationships. First, issue the show ip eigrp neighbors detail
command. Notice that neighbor 10.1.32.2 is an EIGRP stub neighbor advertising static routes. Notice that
R3 is using EIGRP named mode for neighbor 10.1.23.2.
Open configuration window

R3# show ip eigrp neighbors detail

EIGRP-IPv4 Neighbors for AS(64514)
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 10.1.32.2 Gi0/0/1 11 07:40:16 1 100 0 3
Version 25.0/2.0, Retrans: 2, Retries: 0, Prefixes: 1
< some output omitted >

Stub Peer Advertising (STATIC ) Routes

Suppressing queries

EIGRP-IPv4 VR(CISCO) Address-Family Neighbors for AS(64513)

H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) CntNum
0 10.1.23.2 Gi0/0/0 13 07:36:50 1 100 0 39
Version 23.0/2.0, Retrans: 1, Retries: 0, Prefixes: 2
< some output omitted >

e. Issue the show ip route eigrp command for EIGRP named mode, as shown. Notice that the two internal
EIGRP routes are from AS 64513.
R3# show ip route eigrp 64513 | begin Gateway
Gateway of last resort is 10.1.32.2 to network 0.0.0.0

10.0.0.0/8 is variably subnetted, 8 subnets, 2 masks

D 10.1.1.0/24 [90/16000] via 10.1.23.2, 00:34:20, GigabitEthernet0/0/0
D 10.1.12.0/24 [90/15360] via 10.1.23.2, 00:34:20, GigabitEthernet0/0/0

f. Issue the show ip route eigrp command for AS 64514, as shown. Notice that R3 has learned a default
from the EIGRP stub neighbor.
R3# show ip route eigrp 64514 | begin Gateway
Gateway of last resort is 10.1.32.2 to network 0.0.0.0

D*EX 0.0.0.0/0 [170/130816] via 10.1.32.2, 07:47:51, GigabitEthernet0/0/1

g. From R3, ping the Loopback 0 interface on D2. The ping should be successful.
R3# ping 209.165.201.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.201.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/2 ms

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 7 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

h. From R3, ping the Loopback 0 interface on D2 and source the ping from Loopback 0, as shown. The ping
should not be successful.
R3# ping 209.165.201.1 source 10.3.3.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.201.1, timeout is 2 seconds:
Packet sent with a source address of 10.3.3.1
.....
Success rate is 0 percent (0/5)
Close configuration window

Part 2: Configure Two-Way Redistribution on R1

In this part of the lab, you will perform EIGRP-to-EIGRP redistribution on R1. Remember that every protocol
provides a seed metric at the time of redistribution. By default, source protocols, such as OSPF, RIP, IS-IS
redistributed into EIGRP are given an administrative distance of 170 and a seed metric of infinity. This
prevents the installation of the redistributed routes into the EIGRP topology table. However, if an EIGRP AS
redistributes into another EIGRP AS, all the path metrics are preserved and included during redistribution.
Therefore, setting an EIGRP seed metric in not required with performing EIGRP–to–EIGRP redistribution.
When performing redistribution, the router command defines the destination protocol and the redistribute
command identifies the source protocol. For example:
Router(config)# router eigrp 5 !<--destination protocol
Router(config-router)# redistribute eigrp 10 !<--source protocol
In our example, the destination protocol is EIGRP AS 5 and the source protocol is EIGRP 10. This results in
all EIGRP routes from AS 10 being redistributed into EIGRP AS 5.

Step 1: Redistribute EIGRP 64513 into EIGRP 64512.

In this step, you are going to the destination EIGRP AS 64512 to perform redistribution. The source EIGRP
AS is 64513.
Open configuration window

R1(config)# router eigrp 64512

R1(config-router)# redistribute eigrp 64513
R1(config-router)# exit
Close configuration window

Step 2: On D1 Verify One-Way redistribution.

Issue the show ip route eigrp command on D1 to see the external EIGRP routes from AS 64513. Notice that
the external EIGRP routes all originated from AS 64513. Also, notice that a Gateway of last resort has not
been set.
Open configuration window

D1# show ip route eigrp | begin Gateway

Gateway of last resort is not set

10.0.0.0/8 is variably subnetted, 6 subnets, 2 masks

D EX 10.1.1.0/24
[170/130816] via 10.1.11.1, 00:07:40, GigabitEthernet1/0/11
D EX 10.1.12.0/24
[170/3072] via 10.1.11.1, 00:07:40, GigabitEthernet1/0/11
D EX 10.1.23.0/24
[170/3328] via 10.1.11.1, 00:07:40, GigabitEthernet1/0/11
D EX 10.3.3.0/24 [170/3353] via 10.1.11.1, 00:07:40, GigabitEthernet1/0/11
Close configuration window

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 8 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

Step 3: Redistribute EIGRP 64512 into EIGRP 64513.

Next, go to the destination AS 64513 to perform redistribution. The source EIGRP AS is 64512. To
redistribute using an EIGRP named instance, you need to access the topology base, as shown.
Open configuration window

R1(config)# router eigrp CISCO

R1(config-router)# address-family ipv4 unicast autonomous-system 64513
R1(config-router-af)# topology base
R1(config-router-af-topology)# redistribute eigrp 64512
R1(config-router-af-topology)# end
Close configuration window

Step 4: On R3 Verify Two-Way Redistribution on R1.

Issue the show ip route eigrp 64513 | section D EX on D3 to see the external EIGRP routes from AS
64512.
Open configuration window

R3# show ip route eigrp 64513 | section D EX

D EX 10.1.11.0/24
[170/20480] via 10.1.23.2, 00:12:47, GigabitEthernet0/0/0
D EX 198.51.100.0
[170/2580480] via 10.1.23.2, 00:12:47, GigabitEthernet0/0/0
Close configuration window

Part 3: Configure Two-Way Redistribution on R3

In this part of the lab, you will perform EIGRP-to-EIGRP redistribution on R3. Remember a seed metric is not
required.

Step 1: Redistribute EIGRP 64513 into EIGRP 64514.

The redistribute command is always performed on the destination protocol. Start by accessing the EIGRP
process 64514. Then redistribute the source protocol, EIGRP 64513, into the destination protocol, as shown.
Open configuration window

R3(config)# router eigrp 64514

R3(config-router)# redistribute eigrp 64513
R3(config-router)# end
Close configuration window

Step 2: Verify redistribution on D2.

Issue the show ip route eigrp command on D2 to see the external EIGRP routes from AS 64513. Notice that
the highlighted external EIGRP routes originated from AS 64512 and the other four external EIGRP prefixes
originating from AS 64513.
Open configuration window

D2# show ip route eigrp | begin Gateway

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

10.0.0.0/8 is variably subnetted, 7 subnets, 2 masks

D EX 10.1.1.0/24 [170/3353] via 10.1.32.1, 01:34:57, GigabitEthernet1/0/11
D EX 10.1.11.0/24
[170/3584] via 10.1.32.1, 01:34:57, GigabitEthernet1/0/11
D EX 10.1.12.0/24
[170/3328] via 10.1.32.1, 01:34:57, GigabitEthernet1/0/11
D EX 10.1.23.0/24
[170/3072] via 10.1.32.1, 01:34:57, GigabitEthernet1/0/11
D EX 10.3.3.0/24
[170/130816] via 10.1.32.1, 01:34:57, GigabitEthernet1/0/11

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 9 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

198.51.100.0/25 is subnetted, 1 subnets

D EX 198.51.100.0
[170/131584] via 10.1.32.1, 01:34:57, GigabitEthernet1/0/11
Close configuration window

Step 3: Redistribute EIGRP 64514 into EIGRP 64513 on R3.

Next, go to the destination AS 64513 to perform redistribution. To redistribute using an EIGRP named mode
you need to access the topology base. Then, the source AS 64514 is specified using the redistribute
command, as shown.
Open configuration window

R3(config)# router eigrp CISCO

R3(config-router)# address-family ipv4 unicast autonomous-system 64513
R3(config-router-af)# topology base
R3(config-router-af-topology)# redistribute eigrp 64514
R3(config-router-af-topology)# end
Close configuration window

Step 4: On D1 Verify Two-Way Redistribution on R3 and end-to-end connectivity.

a. Issue the show ip route eigrp command on D1 to see the external EIGRP routes. Notice that both of the
highlighted external EIGRP routes originated from AS 64514.
Open configuration window

D1# show ip route eigrp | begin Gateway

Gateway of last resort is 10.1.11.1 to network 0.0.0.0

D*EX 0.0.0.0/0 [170/131584] via 10.1.11.1, 00:01:28, GigabitEthernet1/0/11

10.0.0.0/8 is variably subnetted, 7 subnets, 2 masks
D EX 10.1.1.0/24
[170/130816] via 10.1.11.1, 04:48:32, GigabitEthernet1/0/11
D EX 10.1.12.0/24
[170/3072] via 10.1.11.1, 04:48:32, GigabitEthernet1/0/11
D EX 10.1.23.0/24
[170/3328] via 10.1.11.1, 04:48:32, GigabitEthernet1/0/11
D EX 10.1.32.0/24
[170/3584] via 10.1.11.1, 00:01:28, GigabitEthernet1/0/11
D EX 10.3.3.0/24 [170/3353] via 10.1.11.1, 04:48:32, GigabitEthernet1/0/11

b. Next, from D1 ping the 209.165.201.1 address on D2 using the Loopback 0 address on D1. The ping
should be successful. This verifies full end-to-end connectivity and successful two-way redistribution on
R1 and R3.
D1# ping 209.165.201.1 source 198.51.100.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.201.1, timeout is 2 seconds:
Packet sent with a source address of 198.51.100.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 2/2/4 ms
Close configuration window

Part 4: Filter and Verify Redistribution using a Distribute List and Prefix List
In this part of the lab, we will filter specific EIGRP prefixes being redistributed into AS 64512 on R1 and
advertised to D1. Note that the redistribute command cannot directly reference a prefix list, but a route map
can refer to a prefix list using the match command. In our example, we will bind the prefix list using a
distribute list.

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 10 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

Step 1: Create a prefix list named FILTER and specify the action for each statement.
Only allow the default route, as well as the Loopback 0 address on R1 and R3, to be sent to D1 using the
prefix list name FILTER, as shown on R1. Notice the permit statement allows prefixes to be advertised. The
last statement, sequence 20 filters all other prefixes. If not explicitly set, the deny statement is implied. This is
similar to using an ACL.
Open configuration window

R1(config)# ip prefix-list FILTER seq 5 permit 0.0.0.0/0

R1(config)# ip prefix-list FILTER seq 10 permit 10.1.1.0/24
R1(config)# ip prefix-list FILTER seq 15 permit 10.3.3.0/24
R1(config)# ip prefix-list FILTER seq 20 deny 0.0.0.0/0 le 32

Step 2: Apply the IP Prefix List using the Distribute List command in EIGRP 64512.
Next, apply the prefix-list FILTER to the distribute-list which filters routing advertisements to D1. The out
keyword in the distribute-list command specifies that subnets matching prefix list FILTER will be filtered as
the routing updates exit the GigabitEthernet0/0/1 interface toward D1. Using the keyword in would filter routes
entering the routing table.
R1(config)# router eigrp 64512
R1(config-router)# distribute-list prefix FILTER out GigabitEthernet0/0/1
R1(config-router)# end

Step 3: Verify Route Filtering.

a. Issue the show ip prefix-list detail command on R1 to verify the hit count for each sequence in the prefix
list. Notice in our example the default route has 2 hits while the deny statement has 10 hits.
R1# show ip prefix-list detail
Prefix-list with the last deletion/insertion: FILTER
ip prefix-list FILTER:
count: 4, range entries: 1, sequences: 5 - 20, refcount: 4
seq 5 permit 0.0.0.0/0 (hit count: 2, refcount: 1)
seq 10 permit 10.1.1.0/24 (hit count: 6, refcount: 1)
seq 15 permit 10.3.3.0/24 (hit count: 4, refcount: 2)
seq 20 deny 0.0.0.0/0 le 32 (hit count: 10, refcount: 0)
Close configuration window

b. Issue the show ip route eigrp command on D1 to see the external EIGRP routes. Notice the smaller
routing table on D1.
Open configuration window

D1# show ip route eigrp | begin Gateway

Gateway of last resort is 10.1.11.1 to network 0.0.0.0

D*EX 0.0.0.0/0 [170/131584] via 10.1.11.1, 01:22:55, GigabitEthernet1/0/11

10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks
D EX 10.1.1.0/24
[170/130816] via 10.1.11.1, 00:31:39, GigabitEthernet1/0/11
D EX 10.3.3.0/24 [170/3353] via 10.1.11.1, 00:31:27, GigabitEthernet1/0/11

c. From D1 ping the 209.165.201.1 address on D2 using the Loopback 0 address on D1. The ping should be
successful. This verifies full end-to-end connectivity and successful redistribution on R1 and R3, as well
as route filtering on R1.
D1# ping 209.165.201.1 source 198.51.100.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.201.1, timeout is 2 seconds:
Packet sent with a source address of 198.51.100.1

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 11 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 2/2/3 ms
close configuration window

Reflection Questions
1. Why is a seed metric not required when redistributing EIGRP into another EIGRP process?
Type your answers here.

The seed metrics do not need to be set because the metric values are maintained when redistributing
EIGRP into another EIGRP process.
2. What other source protocol(s), other than EIGRP does not require a seed metric defined for redistribution into
EIGRP?
Type your answers here.

Static routes and directly connected interfaces

3. Which EIGRP prefixes were filtered on R1 and not sent to D1?
Type your answers here.

The 10.1.12.0/24, 10.1.23.0/24 and 10.1.32.0/24 prefixes were filtered on R1 using a prefix-list applied to
a distribute-list.

Router Interface Summary Table

Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2

Fast Ethernet 0/0 Fast Ethernet 0/1

1800 (F0/0) (F0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
Gigabit Ethernet 0/0 Gigabit Ethernet 0/1
1900 (G0/0) (G0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
Fast Ethernet 0/0 Fast Ethernet 0/1
2801 (F0/0) (F0/1) Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
Fast Ethernet 0/0 Fast Ethernet 0/1
2811 (F0/0) (F0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
Gigabit Ethernet 0/0 Gigabit Ethernet 0/1
2900 (G0/0) (G0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
Gigabit Ethernet 0/0/0 Gigabit Ethernet 0/0/1
4221 (G0/0/0) (G0/0/1) Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
Gigabit Ethernet 0/0/0 Gigabit Ethernet 0/0/1
4300 (G0/0/0) (G0/0/1) Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An example
of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in
Cisco IOS commands to represent the interface.
End of document

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 12 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

Device Configs – Final

Router R1
R1# show running-config
Building configuration...

Current configuration : 2181 bytes

!
version 16.9
service timestamps debug datetime msec
service timestamps log datetime msec
platform qfp utilization monitor load 80
no platform punt-keepalive disable-kernel-core
!
hostname R1
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
no ip domain lookup
!
login on-success log
!
subscriber templating
!
multilink bundle-name authenticated
!
spanning-tree extend system-id
!
redundancy
mode none
!
interface Loopback0
ip address 10.1.1.1 255.255.255.0
!
interface GigabitEthernet0/0/0
ip address 10.1.12.1 255.255.255.0
negotiation auto
!
interface GigabitEthernet0/0/1
ip address 10.1.11.1 255.255.255.0
negotiation auto
!
interface Serial0/1/0
no ip address
clock rate 125000

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 13 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

!
interface Serial0/1/1
no ip address
!
router eigrp 64512
distribute-list prefix FILTER out GigabitEthernet0/0/1
network 10.1.11.0 0.0.0.255
redistribute eigrp 64513
eigrp router-id 1.1.1.1
!
router eigrp CISCO
!
address-family ipv4 unicast autonomous-system 64513
!
topology base
redistribute eigrp 64512
exit-af-topology
network 10.1.1.0 0.0.0.255
network 10.1.12.0 0.0.0.255
eigrp router-id 1.1.1.1
exit-address-family
!
ip forward-protocol nd
no ip http server
ip http secure-server
!
ip prefix-list FILTER seq 5 permit 0.0.0.0/0
ip prefix-list FILTER seq 10 permit 10.1.1.0/24
ip prefix-list FILTER seq 15 permit 10.3.3.0/24
ip prefix-list FILTER seq 20 deny 0.0.0.0/0 le 32
!
control-plane
!
banner motd ^C R1, Configure Route Redistribution Within the Same Interior Gateway
Protocol ^C
!
line con 0
exec-timeout 0 0
logging synchronous
transport input none
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
end

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 14 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

Router R2
R2# show run
Building configuration...

Current configuration : 1648 bytes

!
version 16.9
service timestamps debug datetime msec
service timestamps log datetime msec
platform qfp utilization monitor load 80
no platform punt-keepalive disable-kernel-core
!
hostname R2

boot-start-marker
boot-end-marker
!
no aaa new-model
!
no ip domain lookup
!
login on-success log
!
subscriber templating
!
multilink bundle-name authenticated
!
spanning-tree extend system-id
!
redundancy
mode none
!
interface GigabitEthernet0/0/0
ip address 10.1.12.2 255.255.255.0
negotiation auto
!
interface GigabitEthernet0/0/1
ip address 10.1.23.2 255.255.255.0
negotiation auto
!
router eigrp CISCO
!
address-family ipv4 unicast autonomous-system 64513
!
topology base
exit-af-topology
network 10.1.12.0 0.0.0.255
network 10.1.23.0 0.0.0.255

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 15 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

eigrp router-id 2.2.2.2

exit-address-family
!
ip forward-protocol nd
no ip http server
ip http secure-server
!
control-plane
!
banner motd ^C R2, Configure Route Redistribution Within the Same Interior Gateway
Protocol ^C
!
line con 0
exec-timeout 0 0
logging synchronous
transport input none
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
end

Router R3
R3# show running-config
Building configuration...

Current configuration : 1871 bytes

!
version 16.9
service timestamps debug datetime msec
service timestamps log datetime msec
platform qfp utilization monitor load 80
no platform punt-keepalive disable-kernel-core
!
hostname R3
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
no ip domain lookup
!
login on-success log
!
subscriber templating

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 16 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

!
multilink bundle-name authenticated
!
spanning-tree extend system-id
!
redundancy
mode none
!
interface Loopback0
ip address 10.3.3.1 255.255.255.0
!
interface GigabitEthernet0/0/0
ip address 10.1.23.3 255.255.255.0
negotiation auto
!
interface GigabitEthernet0/0/1
ip address 10.1.32.1 255.255.255.0
negotiation auto
!
interface Serial0/1/0
no ip address
!
interface Serial0/1/1
no ip address
!
router eigrp 64514
network 10.1.32.0 0.0.0.255
redistribute eigrp 64513
eigrp router-id 3.3.3.3
!
router eigrp CISCO
!
address-family ipv4 unicast autonomous-system 64513
!
topology base
redistribute eigrp 64514
exit-af-topology
network 10.1.23.0 0.0.0.255
network 10.3.3.0 0.0.0.255
eigrp router-id 3.3.3.3
exit-address-family
!
ip forward-protocol nd
no ip http server
ip http secure-server
!
control-plane
!
banner motd ^C R3, Configure Route Redistribution Within the Same Interior Gateway
Protocol ^C

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 17 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

!
line con 0
exec-timeout 0 0
logging synchronous
transport input none
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
end

Switch D1
D1# show running-config
Building configuration...

Current configuration : 4037 bytes

!
version 16.9
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no platform punt-keepalive disable-kernel-core
!
hostname D1
!
vrf definition Mgmt-vrf
!
address-family ipv4
exit-address-family
!
address-family ipv6
exit-address-family
!
no aaa new-model
switch 1 provision ws-c3650-24ps
!
ip routing
!
no ip domain lookup
!
login on-success log
!
license boot level ipservicesk9
!
diagnostic bootup level minimal
!
spanning-tree mode rapid-pvst

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 18 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

spanning-tree extend system-id

!
redundancy
mode sso
!
transceiver type all
monitoring
!
class-map match-any system-cpp-police-topology-control
description Topology control
class-map match-any system-cpp-police-sw-forward
description Sw forwarding, L2 LVX data, LOGGING
class-map match-any system-cpp-default
description DHCP Snooping, EWLC control, EWCL data
class-map match-any system-cpp-police-sys-data
description Learning cache ovfl, Crypto Control, Exception, EGR Exception, NFL
SAMPLED DATA, RPF Failed
class-map match-any system-cpp-police-punt-webauth
description Punt Webauth
class-map match-any system-cpp-police-l2lvx-control
description L2 LVX control packets
class-map match-any system-cpp-police-forus
description Forus Address resolution and Forus traffic
class-map match-any system-cpp-police-multicast-end-station
description MCAST END STATION
class-map match-any system-cpp-police-multicast
description Transit Traffic and MCAST Data
class-map match-any system-cpp-police-l2-control
description L2 control
class-map match-any system-cpp-police-dot1x-auth
description DOT1X Auth
class-map match-any system-cpp-police-data
description ICMP redirect, ICMP_GEN and BROADCAST
class-map match-any system-cpp-police-stackwise-virt-control
description Stackwise Virtual
class-map match-any non-client-nrt-class
class-map match-any system-cpp-police-routing-control
description Routing control
class-map match-any system-cpp-police-protocol-snooping
description Protocol snooping
class-map match-any system-cpp-police-system-critical
description System Critical and Gold
!
policy-map system-cpp-policy
!
interface Loopback0
ip address 198.51.100.1 255.255.255.128
!
interface GigabitEthernet0/0
vrf forwarding Mgmt-vrf

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 19 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

no ip address
speed 1000
negotiation auto
!
interface GigabitEthernet1/0/1
shutdown
!
interface GigabitEthernet1/0/2
shutdown
!
interface GigabitEthernet1/0/3
shutdown
!
interface GigabitEthernet1/0/4
shutdown
!
interface GigabitEthernet1/0/5
shutdown
!
interface GigabitEthernet1/0/6
shutdown
!
interface GigabitEthernet1/0/7
shutdown
!
interface GigabitEthernet1/0/8
shutdown
!
interface GigabitEthernet1/0/9
shutdown
!
interface GigabitEthernet1/0/10
shutdown
!
interface GigabitEthernet1/0/11
no switchport
ip address 10.1.11.2 255.255.255.0
!
interface GigabitEthernet1/0/12
shutdown
!
interface GigabitEthernet1/0/13
shutdown
!
interface GigabitEthernet1/0/14
shutdown
!
interface GigabitEthernet1/0/15
shutdown
!

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 20 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

interface GigabitEthernet1/0/16
shutdown
!
interface GigabitEthernet1/0/17
shutdown
!
interface GigabitEthernet1/0/18
shutdown
!
interface GigabitEthernet1/0/19
shutdown
!
interface GigabitEthernet1/0/20
shutdown
!
interface GigabitEthernet1/0/21
shutdown
!
interface GigabitEthernet1/0/22
shutdown
!
interface GigabitEthernet1/0/23
shutdown
!
interface GigabitEthernet1/0/24
shutdown
!
interface GigabitEthernet1/1/1
!
interface GigabitEthernet1/1/2
!
interface GigabitEthernet1/1/3
!
interface GigabitEthernet1/1/4
!
interface Vlan1
no ip address
!
router eigrp 64512
network 10.1.11.0 0.0.0.255
network 198.51.100.0
eigrp router-id 11.11.11.11
!
ip forward-protocol nd
ip http server
ip http secure-server
!
control-plane
service-policy input system-cpp-policy
!

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 21 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

banner motd ^C D1, Configure Route Redistribution Within the Same Interior Gateway
Protocol ^C
!
line con 0
logging synchronous
transport output none
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
line vty 5 15
login
!
end

Switch D2
D2# show running-config
Building configuration...

Current configuration : 4069 bytes

!
version 16.9
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no platform punt-keepalive disable-kernel-core
!
hostname D2
!
vrf definition Mgmt-vrf
!
address-family ipv4
exit-address-family
!
address-family ipv6
exit-address-family
!
no aaa new-model
switch 1 provision ws-c3650-24ps
!
ip routing
!
no ip domain lookup
!
login on-success log
!
license boot level ipservicesk9
!

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 22 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

diagnostic bootup level minimal

!
spanning-tree mode rapid-pvst
spanning-tree extend system-id
!
redundancy
mode sso
!
transceiver type all
monitoring
!
class-map match-any system-cpp-police-topology-control
description Topology control
class-map match-any system-cpp-police-sw-forward
description Sw forwarding, L2 LVX data, LOGGING
class-map match-any system-cpp-default
description DHCP Snooping, EWLC control, EWCL data
class-map match-any system-cpp-police-sys-data
description Learning cache ovfl, Crypto Control, Exception, EGR Exception, NFL
SAMPLED DATA, RPF Failed
class-map match-any system-cpp-police-punt-webauth
description Punt Webauth
class-map match-any system-cpp-police-l2lvx-control
description L2 LVX control packets
class-map match-any system-cpp-police-forus
description Forus Address resolution and Forus traffic
class-map match-any system-cpp-police-multicast-end-station
description MCAST END STATION
class-map match-any system-cpp-police-multicast
description Transit Traffic and MCAST Data
class-map match-any system-cpp-police-l2-control
description L2 control
class-map match-any system-cpp-police-dot1x-auth
description DOT1X Auth
class-map match-any system-cpp-police-data
description ICMP redirect, ICMP_GEN and BROADCAST
class-map match-any system-cpp-police-stackwise-virt-control
description Stackwise Virtual
class-map match-any non-client-nrt-class
class-map match-any system-cpp-police-routing-control
description Routing control
class-map match-any system-cpp-police-protocol-snooping
description Protocol snooping
class-map match-any system-cpp-police-system-critical
description System Critical and Gold
!
policy-map system-cpp-policy
!
interface Loopback0
ip address 209.165.201.1 255.255.255.128

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 23 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

!
interface GigabitEthernet0/0
vrf forwarding Mgmt-vrf
no ip address
speed 1000
negotiation auto
!
interface GigabitEthernet1/0/1
shutdown
!
interface GigabitEthernet1/0/2
shutdown
!
interface GigabitEthernet1/0/3
shutdown
!
interface GigabitEthernet1/0/4
shutdown
!
interface GigabitEthernet1/0/5
shutdown
!
interface GigabitEthernet1/0/6
shutdown
!
interface GigabitEthernet1/0/7
shutdown
!
interface GigabitEthernet1/0/8
shutdown
!
interface GigabitEthernet1/0/9
shutdown
!
interface GigabitEthernet1/0/10
shutdown
!
interface GigabitEthernet1/0/11
no switchport
ip address 10.1.32.2 255.255.255.0
!
interface GigabitEthernet1/0/12
shutdown
!
interface GigabitEthernet1/0/13
shutdown
!
interface GigabitEthernet1/0/14
shutdown
!

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 24 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

interface GigabitEthernet1/0/15
shutdown
!
interface GigabitEthernet1/0/16
shutdown
!
interface GigabitEthernet1/0/17
shutdown
!
interface GigabitEthernet1/0/18
shutdown
!
interface GigabitEthernet1/0/19
shutdown
!
interface GigabitEthernet1/0/20
shutdown
!
interface GigabitEthernet1/0/21
shutdown
!
interface GigabitEthernet1/0/22
shutdown
!
interface GigabitEthernet1/0/23
shutdown
!
interface GigabitEthernet1/0/24
shutdown
!
interface GigabitEthernet1/1/1
!
interface GigabitEthernet1/1/2
!
interface GigabitEthernet1/1/3
!
interface GigabitEthernet1/1/4
!
interface Vlan1
no ip address
!
router eigrp 64514
network 10.1.32.0 0.0.0.255
redistribute static
eigrp router-id 22.22.22.22
eigrp stub static
!
ip forward-protocol nd
ip http server
ip http secure-server

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 25 of 26 www.netacad.com
Lab - Configure Route Redistribution Within the Same Interior Gateway Protocol

ip route 0.0.0.0 0.0.0.0 Loopback0

!
control-plane
service-policy input system-cpp-policy
!!
banner motd ^C D2, Configure Route Redistribution Within the Same Interior Gateway
Protocol ^C
!
line con 0
logging synchronous
transport output none
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
line vty 5 15
login
!
end

 2020 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 26 of 26 www.netacad.com