Term Paper 3: Rssi, Toa, Tdoa Are Three Techniques For Distance Estimation. Which One Would Be The Most Appropriate and Why?

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 2

Term Paper 3: RSSI, ToA, TDoA are three techniques for distance estimation.

Which one would be the most appropriate and why?


Received signal strength indicator
Assuming that the transmission power Ptx, the path loss model, and the path loss coefficient α
are known, the receiver can use the received signal strength Prcvd to solve for the distance d in a
path loss equation like

This is appealing since no additional hardware is necessary and distance estimates can even be
derived without additional overhead from communication that is taking place anyway. The
disadvantage, however, is that RSSI values are not constant but can heavily oscillate, even when
sender and receiver do not move. This is caused by effects like fast fading and mobility of the
environment – ranging errors of ±50% are reported, for example, by Savarese et al. To some
degree, this effect can be counteracted by repeated measurements and filtering out incorrect
values by statistical techniques. In addition, simple, cheap radio transceivers are often not
calibrated and the same actual signal strength can result in different RSSI values on different
devices; similarly, the actual transmission power of such a transceiver shows discrepancies from
the intended power. A third problem is the presence of obstacles in combination with multipath
fading. Here, the signal attenuation along an indirect path, which is higher than along a direct
path, can lead to incorrectly assuming a longer distance than what is actually the case. As this is
a structural problem, it cannot be combated by repeated measurements.
A more detailed consideration shows that mapping RSSI values to distances is actually a random
process. Ramadurai and Sichitiu, for example, collected, for several distances, repeated samples
of RSSI values in an open field setup. Then, they counted how many times each distance resulted
in a given RSSI value and computed the density of this random variable – Figure 1(a) shows this
probability density function for a single given value of RSSI, Figure 1(b) for several. The
information provided in particular by small RSSI values, indicating longer distances, is quite
limited as the density is widely spread.

Figure 1: Random nature of mapping RSSI values to distances. Reproduced by permission of V. Ramadurai and M.
L. Sichitiu
Hence, when using RSSI as a ranging technique, it is necessary to accept and deal with
considerable ranging errors or to treat the outcome of the ranging process as a stochastic result to
begin with.

Time of arrival
Time of Arrival (ToA) (also sometimes called “time of flight”) exploits the relationship between
distance and transmission time when the propagation speed is known. Assuming both sender and
receiver know the time when a transmission – for example, a short ultrasound pulse – starts, the
time of arrival of this transmission at the receiver can be used to compute propagation time and,
thus, distance. To relieve the receiver of this duty, it can return any received “measurement
pulse” in a deterministic time; the original sender then only has to measure the round trip time
assuming symmetric paths.
Depending on the transmission medium that is used, time of arrival requires very high resolution
clocks to produce results of acceptable accuracy. For sound waves, these resolution requirements
are modest; they are very hard for radio wave propagation.
One disadvantage of sound is that its propagation speed depends on external factors such as
temperature or humidity – careful calibration is necessary but not obvious.

Time difference of arrival


To overcome the need for explicit synchronization, the Time Difference of Arrival (TDoA)
method utilizes implicit synchronization by directly providing the start of transmission
information to the receiver. This can be done if two transmission mediums of very different
propagation speeds are used – for example, radio waves propagating at the speed of light and
ultrasound, with a different in speed of about six orders of magnitude. Hence, when a sender
starts an ultrasound and a radio transmission simultaneously, the receiver can use the arrival of
the radio transmission to start measuring the time until arrival of the ultrasound transmission,
safely ignoring the propagation time of the radio communication.
The obvious disadvantage of this approach is the need for two types of senders and receivers on
each node. The advantage, on the other hand, is a considerably better accuracy compared to
RSSI-based approaches. This concept and variations of it have been used in various research
efforts and accuracies of down to 2 cm have been reported.

Discussion
There is a clear trade-off between ranging error and complexity/cost. RSSI-based approaches are
simpler and work with hardware that is required anyway; TDoA-based approaches provide
superior ranging results but need more complex and additional hardware, which also adds to
energy consumption. The open question is thus whether it is possible to solve the actual
positioning or localization problem based on the error-prone measurements provided by RSSI-
based approaches or whether the overhead for TDoA is unavoidable.
There is a number of additional work on making ranging measurements more reliable, for
example, by using acoustic ranging as opposed to radio frequency attenuation or by considering
the effects introduced by quantizing RSSI values (in effect, proximity systems can be regarded as
yes/no quantizations of RSSI)

You might also like