Saudi Aramco 5645-1-ENG (11/2010)

SAUDI ARABIAN OIL COMPANY

FOR CONSTRUCTION UNTIL CERTIFIED

SAFETY INSTRUCTION SHEET FOR CROSS COUNTRY PIPELINE - MAIN LINE PIPE

THIS REVISION IS NOT TO BE USED

1 PIPELINE NAME 2 START POINT 3 END POINT 4 SERVICE 5 VALVE OPER. DIAGRAM 6 YR. BUILT

PI&D: RA-640539.001,
36"-SW-0648-6LE0W04 M93-L-0002 M97-L-0001 SUPPLY WATER

AND DATED
RA-640540.001
7 THIS LINE BEGINS AT Km. 0 8 THIS SHEET BEGINS AT Km. 0
ISSUED FOR 90% REVIEW
REVISION DESCRIPTION

9 MAIN PIPELINE, SHEET: 1 THROUGH: 2 10 CRITICAL PIPING, SHEET: 3 THROUGH: 10

SEGMENTS 11 1

12 NOMINAL PIPE DIAMETER 36 in.

13 NOM. WALL THICKNESS (Tn) 0.625 in.

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
14 MATERIAL GRADE OF PIPE (eg. GR. B, X 52, etc) X70

15 STARTING AT Km. 0

16 ENDING AT Km. 0+72.3

07/15/2019

17 LENGTH - (Feet) 237204.7

DATE

10-02454-0003

18 LENGTH - (Meters) 72300

JOB ORDER/EWO NO.

19 PROCESS OF MANUFACTURE (ERW, SMLS, SAW, etc.) SAW

20 S.M.Y.S. OF PIPE - (PSI) 70,000

REV. NO.

EQUIPMENT DATA

21 FLANGE RATING 600

A

22 CONSTRUCTION TYPE (B:BURIED, AGR or AGN: ABOVE GROUND) B

23 COATING TYPE (FBE,TAP, EXTERNAL, INTERNAL) FBE

24 RATING 600
BY/DATE
OTHER

25 FACING RF

26 MATERIAL C.S.

27 SPEC. / GR. A860 WPHY-70

28 NOTES
OPERATIONS/DATE

1.MATERIAL IN POSITION 26 PERTAINS TO FLANGES; MATERIAL IN POSITION 27 PERTAINS TO BUTT-WELDING FITTINGS AS PER MSS SP-75
07/15/2019
MMM
REVIEW FOR KEY DRAWINGS
REQUIRED (SAUDI ARAMCO)

CONST. AGENCY/DATE

29 M.A.O.P. AT DESIGN FACTOR (D.F.) PSIG 1,367

07/15/2019

30 M.A.O.P. LIMITING FACTOR VALVE

MTG

31 DESIGN FACTOR (eg., 0.5,0.72 ,0.6, etc.) 0.72

32 DESIGN TEMPERATURE oF 194

33 MINIMUM TIE IN TEMPERATURE oF 70

34 ALLOWABLE BENDING STRESS (Sb) PSIG 20,418

CERTIFIED/DATE

35 CALCULATED WALL THICKNESS @ MAOP & D.F. (TMIN - inch.) 0.464

07/15/2019
OAB
DESIGN CERTIFICATION

36 PRESSURE AT LOW POINT - PSIG 2,188

(DESIGN AGENCY)

INITIAL
37 TEST DATE **
PRESSURE TEST
38 LIMITED BY PIPE
OPERATING LIMITS

39 PRESSURE AT LOW POINT - PSIG **

REVALIDATION
ENGG./DATE

40 TEST DATE **
07/15/2019

PRESSURE TEST
BEK

41 LIMITED BY **
INSTRUMENT 42 BASE LINE RUN DATE **
SCRAPING
TEST 43 LATEST RUN DATE **

44 SYSTEM M.A.O.P. 1300 PSIG 45 LIMITED BY: DESIGN PRESSURE

46 REMARKS

** TO BE FILLED OUT BY CONSTRUCTION CONTRACTOR DURING TESTING

IS COVERED, FOR ALL APPROVAL

AND CERTIFICATION REQUIREMENTS, PER SAEP-334, UNDER

REVISION VALIDATION

10-02454-0003
DRAWING COMPLETION CERTIFICATE NO.

47 REFERENCE DWGS.
A

PIPELINE MATERIAL SPECIFICATION: RE-789964

HYDROSTATIC TEST DRAWING : RA-789962.001,002
THIS REVISION NO.

SIS FOR 36" TRUNKLINE DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT.NO. REV. NO

SIS:MAINLINE PIPING FROM WATER SUPPLY FACILITIES TO UTILITY UNITS SIS

TANAJIB UTILITIES UNIT M93 / M97 A RE-789974 001 A
TANAJIB SAUDI ARABIA
EKRD/5645-1-1110.XLS
Saudi Aramco 2616-ENG (11/2010)

SAUDI ARABIAN OIL COMPANY

UNTIL CERTIFIED AND DATED

THIS REVISION IS NOT TO BE
USED FOR CONSTRUCTION N OT E: T H E IN T E N T O F T H IS S H E E T IS T O S H O W A LL C A LC ULA T IO N S A N D R E F E R E N C E D O C UM E N T S
ISSUED FOR 90% REVIEW
REVISION DESCRIPTION

T H A T WE R E US E D T O G E N E R A T E T H E S IS S H E E T .

1. FOR 36" 0.625" WT. A P I 5L - GR X70 SA W P IP E: M AXIM UM ALLOWABLE OPERATING PRESSURE (M AOP):

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
1.1 M AOP FLANGE = 1500 psig (600# Class @ 194°F, ASM E B16.47)

2 X 70000 X 0.625 X 0.72 (M at erial group 1.7)

M AOP PIPE = = 1750 psig
36.000 1.2 M AOP PIPE = 2 X SM YS X TCOR X F
D (B16.34, M at erial group 1.1)
1.3 M AOP VALVES = 1367 psig

WHERE:

1750 psig > 1500 psig > 1367 psig DESIGN PRESSURE = 1300 psi
07/15/2019

THEREFORE M AOP AT DESIGN FACTOR: 1367 psig SM YS = SPECIFIED M IN YIELD STRENGTH = 70000 psi
DATE

10-02454-0003

LI M I T ED B Y : VALVE Tn = NOM INAL (SELECTED) WALL THICKNESS = 0.625 in

JOB ORDER/EWO NO.

F = DESIGN FACTOR = 0.72

D = OUTSIDE DIAM ETER OF PIPE = 36.000 in

REV. NO.

1367 psig > 1300 psig dT = DESIGN TEM P. - M IN TIE-IN TEM P. 194-70 = 124 °F
A

THEREFORE SYSTEM M AOP: 1300 psig TCOR = CORRODED WALL THICKNESS = T n - CA = 0.625 in

LI M I T ED B Y : DESIGN PRESSURE CA = CORROSION ALLOWANCE = 0.000 in

2. INITIA L TEST P RESSURE (NEW P IP E): 2188 psig M AXIM UM ALLOWABLE TEST PRESSURE:
BY/DATE
OTHER

2.1 FOR ASM E 600# FLANGES(GR 1.7)PER ASM E B16.47 2250 psig
2 X 0.90 X 70000 X 0.625
PT = = 2188 psig
36.000

2250 psig > 2188 psig

OPERATIONS/DATE

07/15/2019

3. INITIA L TEST P RESSURE LIM ITED B Y:

MMM
REVIEW FOR KEY DRAWINGS
REQUIRED (SAUDI ARAMCO)

PIPE

4. SYSTEM M A X. OP ERA TING P RESSURE, M A OP :

M AOP = 1300 psig

5. SA FETY VA LVE SET P RESSURE:

CONST. AGENCY/DATE

07/15/2019

1.05 X PT 2297 psig

MTG

6. Tm WA LL THICKNESS:

1300 X 36.000 M INIM UM REQUIRED WALL THICKNESS,

M AOP X D
Tm = = 0.464 inch Tm = = BASED ON SYSTEM M AOP & DESIGN
2 X 70000 X 0.72 2 X SM YS X F FACTOR
CERTIFIED/DATE

07/15/2019

T CA = 0.625 - 0.464 = 0.161 inch T CA = T n - T m = WALL THICKNESS IN EXCESS OF T m

OAB
DESIGN CERTIFICATION

SELECTED WALL THICKNESS = T n

(DESIGN AGENCY)

= 0.625 inch

7. A LLOWA B LE B ENDING STRESS Sb: WHERE:

Sb = Sc - 0.7 Sh - St (PER SAES-L-450) S b =ALLOWABLE BENDING STRESS, PSI SC =COMBINED STRESS, PSI
ENGG./DATE

07/15/2019

Sh =HOOP STRESS, PSI S t =TEMPERATURE STRESS, PSI

BEK

Sc = SM YS, When Sh < 0.65 SM YS = 70000 psi T1 =DESIGN TEMPERATURE, DEGF P =SEG MAOP, PSIG

T2 =TIE- IN TEMPERATURE , DEGF D =OUTSIDE DIAMETER, INCH

a =COEFFICIENT OF THERMAL EXPANSION = 0.0000065 IN / IN / °F

P X D 1300 X 36.000 E =MODULUS OF ELASTICITY = 29000000 psi

Sh = = = 37440 psi
2 X (Tn - CA) 2 X 0.625

0.65*SM YS = 45500 psi

M IN. ALLOWABLE BEND RADIUS = R = ED / (2*Sb ) = 649 M
AND CERTIFICATION REQUIREMENTS, PER SAEP-334, UNDER
IS COVERED, FOR ALL APPROVAL

Sc = 0.9 x SM YS, When Sh > 0.65 SM YS = 63000 psi ANGLE PER 30 M ETERS = 30 / (2*R) = 0.0231 RADIANS = 1.323 DEG

ALLOW FOR M ISALIGNM ENT = 0.0044 RADIANS = 0.252 DEG

St = E X a X dT = 188.5 (T1 - T2) = 23374 psi PERM ISIBLE SLOPE CHANGE = 0.0187 RADIANS = 1.071 DEG
REVISION VALIDATION

Theref ore M AX. ALLOWABLE SLOPE CHANGE = 0.561 m per 30 met ers run
DRAWING COMPLETION CERTIFICATE NO.

10-02454-0003

Sb = Sc - 0.7 Sh - St = 20418 psi OR 1.840 Ft . per 100 f t . run

A THIS REVISION NO.

SIS FOR 36" TRUNKLINE DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT.NO REV.NO.

SIS:MAINLINE PIPING FROM WATER SUPPLY FACILITIES TO UTILITY UNITS SIS

TANAJIB UTILITIES UNIT M93/M97 A RE-789974 002 A
TANAJIB SAUDI ARABIA
EKRD/2616-1110.XLS
Saudi Aramco 5645-2-ENG (11/2010)

SAUDI ARABIAN OIL COMPANY

THIS REVISION IS NOT TO BE USED FOR

CONSTRUCTION UNTIL CERTIFIED AND
SAFETY INSTRUCTION SHEET FOR CROSS COUNTRY PIPELINE - CRITICAL PIPING
1 PIPELINE NAME 2 START POINT 3 END POINT 4 SERVICE 5 VALVE OPER. DIAGRAM 6 YR. BUILT

36"-SW-0639-6LE0W04 M93-L-0002 TANAJIB UTILITY UNIT SUPPLY WATER RA-640539.001

DATED
7 EQUIPMENT NAME M93-L-0002 EQUIPMENT NAME
ISSUED FOR 90% REVIEW
REVISION DESCRIPTION

8 LOCATION (@ Km.) TANAJIB UTILITY UNIT LOCATION (@ Km.)

9 SECTION SECTION

10 EQUIP. CATEGORY PIPELINE EQUIP. CATEGORY

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
11 SIZE in. 36 in. 4 in. 2 in. SIZE in.

12 W.T. in. 0.625 0.188 0.154 W.T. in.

13 MATERIAL CS CS CS MATERIAL
PIPE

PIPE
14 WELD TYPE SAW SMLS SMLS WELD TYPE
07/15/2019

15 SPEC. / GR. X70 X65 X65 SPEC. / GR.

DATE

10-02454-0003

16 COATING TYPE FBE FBE FBE COATING TYPE

JOB ORDER/EWO NO.

EQUIPMENT DATA

17 RATING MATCH TO PIPE MATCH TO PIPE MATCH TO PIPE RATING

FITTING

FITTING
18 FACING BW BW BW FACING
REV. NO.

19 MATERIAL CS CS CS MATERIAL
A

20 SPEC. / GR. A860 WPHY-70 A860 WPHY-70 A860 WPHY-70 SPEC. / GR.

21 REMARKS REMARKS
BY/DATE
OTHER

OPERATIONS/DATE

07/15/2019

22 FLANGE RATING 600 600 600 FLANGE RATING

MMM

23 FLANGE FACING RF RF RF FLANGE FACING

24 FLANGE MAT'L SPECIFICATION A859 A CL2 A859 A CL2 A859 A CL2 FLANGE MAT'L SPECIFICATION
REVIEW FOR KEY DRAWINGS
REQUIRED (SAUDI ARAMCO)

25 M.A.O.P. 1367 PSIG, LIMITED BY: VALVE M.A.O.P. PSIG, LIMITED BY:
26 DESIGN FACTOR 0.72 DESIGN FACTOR
27 DESIGN TEMPERATURE: 194 oF DESIGN TEMPERATURE: (°F) oF
28 TEST PRESSURE 2188 PSIG TEST PRESSURE PSIG
OPERATING LIMITS
CONST. AGENCY/DATE

INITIAL INITIAL
PRESSURE 29 TEST DATE PRESSURE TEST DATE
07/15/2019

TEST TEST
30 LIMITED BY PIPE LIMITED BY
MTG

31 TEST PRESSURE PSIG TEST PRESSURE PSIG

REVALIDATION 32 TEST DATE REVALIDATION TEST DATE

33 LIMITED BY LIMITED BY
34 SYSTEM M.A.O.P. 1300 PSIG SYSTEM M.A.O.P. PSIG

35 LIMITED BY * LIMITED BY

36 SAFETY VALVE SET PRESS. 2297 PZV SAFETY VALVE SET PRESS. PZV
CERTIFIED/DATE

07/15/2019

DES THK @ 37 PIPE SIZE 36 in. 4 in. 2 in. DES THK @ PIPE SIZE in. in. in.
OAB

SYSTEM MAOP 38 PIPE Tm 0.464 in. 0.063 in. 0.033 in. SYSTEM MAOP PIPE Tm in. in. in.
DESIGN CERTIFICATION
(DESIGN AGENCY)

& DES TEMP 39 PIPE Tca 0.161 in. 0.126 in. 0.121 in. & DES TEMP PIPE Tca in. in. in.
40 OSI DATA POINTS OSI DATA POINTS
OSI DATA POINT INFO.

SEQ. DATE WT(in). DATE WT(in). DATE WT(in). SEQ. DATE WT(in). DATE WT(in). DATE WT(in).

1 1
ENGG./DATE

07/15/2019

2 2
BEK

3 3

4 4

5 5

6 6

41 REMARKS REMARKS

* LIMITED BY DESIGN CONDITION

IS COVERED, FOR ALL APPROVAL

AND CERTIFICATION REQUIREMENTS, PER SAEP-334, UNDER

REVISION VALIDATION

10-02454-0003

42 REFERENCE DWGS REFERENCE DWGS

DRAWING COMPLETION CERTIFICATE NO.

P&ID : RA-640539.001

PIPELINE MATERIAL SPECIFICATION: RE-789964

HYDROSTATIC TEST DRAWING : RA-789962.001

A THIS REVISION NO.

SIS FOR 36" TRUNKLINE (M93-L-0002) DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO

SIS:MAINLINE PIPING FROM WATER SUPPLY FACILITIES TO UTILITY UNITS SIS

TANAJIB WATER SUPPLY FACILITIES M93 A RE-789974 003 A
TANAJIB SAUDI ARABIA
EKRD/5645-2-1110.XLS

150 RF
Saudi Aramco 2616-ENG (11/2010)

SAUDI ARABIAN OIL COMPANY

UNTIL CERTIFIED AND DATED

THIS REVISION IS NOT TO BE
USED FOR CONSTRUCTION
NOTE: THE INTENT OF THIS SHEET IS TO SHOW ALL CALCULATIONS AND REFERENCE DOCUMENTS
ISSUED FOR 90% REVIEW

THAT WERE USED TO GENERATE THE SIS SHEET.

REVISION DESCRIPTION

1. FOR 36" 0.625" WT. API 5L - GR X70 SAW PIPE: MAXIMUM ALLOWABLE OPERATING PRESSURE (MAOP):

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
1.1 MAOP FLANGE = 1500 psig (600# Class @ 194 °F, ASME B16.47)

2 X 70000 X 0.625 X 0.72 (Material group 1.7)

MAOP PIPE = = 1750 psig
36.000 1.2 MAOP PIPE = 2 X SMYS X TCOR X F
D (B16.34, Material group 1.1)
1.3 MAOP VALVES = 1367 psig

WHERE:
1750 psig > 1500 psig > 1367 psig DESIGN PRESSURE = 1300 psi
07/15/2019

THEREFORE MAOP AT DESIGN FACTOR: 1367 psig SMYS = SPECIFIED MIN YIELD STRENGTH = 70000 psi
DATE

10-02454-0003

LIMITED BY: VALVE Tn= NOMINAL (SELECTED) WALL THICKNESS = 0.625 in

JOB ORDER/EWO NO.

F = DESIGN FACTOR = 0.72

D = OUTSIDE DIAMETER OF PIPE = 36.000 in

REV. NO.

1367 psig > 1300 psig dT = DESIGN TEMP. - MIN TIE-IN TEMP. 194 - 70 = 124 °F
A

THEREFORE SYSTEM MAOP: 1300 psig TCOR = CORRODED WALL THICKNESS = Tn - CA = 0.625 in

LIMITED BY: DESIGN PRESSURE CA = CORROSION ALLOWANCE = 0.000 in

2. INITIAL TEST PRESSURE (NEW PIPE): 2188 psig MAXIMUM ALLOWABLE TEST PRESSURE:
BY/DATE
OTHER

2.1 FOR ASME 600# FLANGES (GR 1.7)PER ASME B16.47 2250 psig
2 X 0.90 X 70000 X 0.625
PT = = 2188 psig
36.000

2250 psig > 2188 psig

OPERATIONS/DATE

07/15/2019

3. INITIAL TEST PRESSURE LIMITED BY:

MMM
REVIEW FOR KEY DRAWINGS
REQUIRED (SAUDI ARAMCO)

PIPE

4. SYSTEM MAX. OPERATING PRESSURE, MAOP:

MAOP = 1300 psig

5. SAFETY VALVE SET PRESSURE:

CONST. AGENCY/DATE

07/15/2019

1.05 X PT 2297 psig

MTG

6. Tmin WALL THICKNESS:

1300 X 36.000 MINIMUM REQUIRED WALL THICKNESS,

MAOP X D
Tm = = 0.464 inch Tm = BASED ON SYSTEM MAOP & DESIGN
2 X 70000 X 0.72 2 X SMYS X F FACTOR
CERTIFIED/DATE

07/15/2019

TCA = 0.625 - 0.464 = 0.161 inch TCA = Tn - Tm WALL THICKNESS IN EXCESS OF Tm

OAB
DESIGN CERTIFICATION
(DESIGN AGENCY)

SELECTED WALL THICKNESS = Tn = 0.625 inch

ENGG./DATE

07/15/2019
BEK
AND CERTIFICATION REQUIREMENTS, PER SAEP-334, UNDER
IS COVERED, FOR ALL APPROVAL
REVISION VALIDATION

DRAWING COMPLETION CERTIFICATE NO.

10-02454-0003
A THIS REVISION NO.

SIS FOR 36" TRUNKLINE (M93-L-0002) DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT.NO REV.NO.

SIS:MAINLINE PIPING FROM WATER SUPPLY FACILITIES TO UTILITY UNITS SIS

TANAJIB WATER SUPPLY FACILITIES M93 A RE-789974 004 A
TANAJIB SAUDI ARABIA
EKRD/2616-1110.XLS
Saudi Aramco 2616-ENG (11/2010)

SAUDI ARABIAN OIL COMPANY

UNTIL CERTIFIED AND DATED

THIS REVISION IS NOT TO BE
USED FOR CONSTRUCTION
N OT E: T H E IN T E N T O F T H IS S H E E T IS T O S H O W A LL C A LC ULA T IO N S A N D R E F E R E N C E D O C UM E N T S
ISSUED FOR 90% REVIEW

T H A T WE R E US E D T O G E N E R A T E T H E S IS S H E E T .
REVISION DESCRIPTION

1. FOR 4.5" 0.188" WT. A P I 5L - GR X65 SM LS P IP E: M AXIM UM ALLOWABLE OPERATING PRESSURE (M AOP):

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
1.1 M AOP FLANGE = 1500 psig (600# Class @ 194 °F, ASM E B16.5)

2 X 65000 X 0.188 X 0.72 (M at erial group 1.7)

M AOP PIPE = = 3910 psig
4.500 1.2 M AOP PIPE = 2 X SM YS X T COR X F
D ( B16.34, M at erial group 2.8)
1.3 M AOP VALVES = 1490 psig

WHERE:
3910 psig > 1500 psig > 1490 psig DESIGN PRESSURE = 1300 psi
07/15/2019

THEREFORE M AOP AT DESIGN FACTOR: 1490 psig SM YS = SPECIFIED M IN YIELD STRENGTH = 65000 psi
DATE

10-02454-0003

LI M I T ED B Y : VALVE Tn= NOM INAL (SELECTED) WALL THICKNESS = 0.188 in

JOB ORDER/EWO NO.

F = DESIGN FACTOR = 0.72

D = OUTSIDE DIAM ETER OF PIPE = 4.500 in

REV. NO.

1490 psig > 1300 psig dT = DESIGN TEM P. - M IN TIE-IN TEM P. 194 - 70 = 124 °F
A

THEREFORE SYSTEM M AOP: 1300 psig TCOR = CORRODED WALL THICKNESS = T n - CA = 0.188 in

LI M I T ED B Y : DESIGN PRESSURE CA = CORROSION ALLOWANCE = 0.000 in

2. INITIA L TEST P RESSURE (NEW P IP E): 2250 psig M AXIM UM ALLOWABLE TEST PRESSURE:
BY/DATE
OTHER

2.1 FOR ASM E 600# FLANGES (GR 1.7)PER ASM E B16.5 2250 psig
2 X 0.90 X 65000 X 0.188
PT = = 4888 psig
4.500

4888 psig > 2250 psig

OPERATIONS/DATE

07/15/2019

3. INITIA L TEST P RESSURE LIM ITED B Y:

MMM
REVIEW FOR KEY DRAWINGS
REQUIRED (SAUDI ARAMCO)

FLANGE

4. SYSTEM M A X. OP ERA TING P RESSURE, M A OP :

M AOP = 1300 psig

5. SA FETY VA LVE SET P RESSURE:

CONST. AGENCY/DATE

07/15/2019

1.05 X PT 2363 psig

MTG

6. Tmin WA LL THICKNESS:

1300 X 4.500 M INIM UM REQUIRED WALL THICKNESS,

M AOP X D
Tm = = 0.063 inch Tm = BASED ON SYSTEM M AOP & DESIGN
2 X 65000 X 0.72 2 X SM YS X F FACTOR
CERTIFIED/DATE

07/15/2019

T CA = 0.188 - 0.063 = 0.126 inch T CA = T n - T m WALL THICKNESS IN EXCESS OF T m

OAB
DESIGN CERTIFICATION
(DESIGN AGENCY)

SELECTED WALL THICKNESS = T n = 0.188 inch

ENGG./DATE

07/15/2019
BEK
AND CERTIFICATION REQUIREMENTS, PER SAEP-334, UNDER
IS COVERED, FOR ALL APPROVAL
REVISION VALIDATION

DRAWING COMPLETION CERTIFICATE NO.

10-02454-0003
A THIS REVISION NO.

SIS FOR 36" TRUNKLINE (M93-L-0002) DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT.NO REV.NO.

SIS:MAINLINE PIPING FROM WATER SUPPLY FACILITIES TO UTILITY UNITS SIS

TANAJIB WATER SUPPLY FACILITIES M93 A RE-789974 005 A
TANAJIB SAUDI ARABIA
EKRD/2616-1110.XLS
Saudi Aramco 2616-ENG (11/2010)

SAUDI ARABIAN OIL COMPANY

UNTIL CERTIFIED AND DATED

THIS REVISION IS NOT TO BE
USED FOR CONSTRUCTION
N OT E: T H E IN T E N T O F T H IS S H E E T IS T O S H O W A LL C A LC ULA T IO N S A N D R E F E R E N C E D O C UM E N T S
ISSUED FOR 90% REVIEW

T H A T WE R E US E D T O G E N E R A T E T H E S IS S H E E T .
REVISION DESCRIPTION

1. FOR 2.375" 0.154" WT. A P I 5L - GR X65 SM LS P IP E: M AXIM UM ALLOWABLE OPERATING PRESSURE (M AOP):

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
1.1 M AOP FLANGE = 1500 psig (600# Class @ 194 °F, ASM E B16.5)

2 X 65000 X 0.154 X 0.72 (M at erial group 1.7)

M AOP PIPE = = 6069 psig
2.375 1.2 M AOP PIPE = 2 X SM YS X T COR X F
D ( B16.34, M at erial group 2.8)
1.3 M AOP VALVES = 1490 psig

WHERE:
6069 psig > 1500 psig > 1490 psig DESIGN PRESSURE = 1300 psi
07/15/2019

THEREFORE M AOP AT DESIGN FACTOR: 1490 psig SM YS = SPECIFIED M IN YIELD STRENGTH = 65000 psi
DATE

10-02454-0003

LI M I T ED B Y : VALVE Tn= NOM INAL (SELECTED) WALL THICKNESS = 0.154 in

JOB ORDER/EWO NO.

F = DESIGN FACTOR = 0.72

D = OUTSIDE DIAM ETER OF PIPE = 2.375 in

REV. NO.

1490 psig > 1300 psig dT = DESIGN TEM P. - M IN TIE-IN TEM P. 194 - 70 = 124 °F
A

THEREFORE SYSTEM M AOP: 1300 psig TCOR = CORRODED WALL THICKNESS = T n - CA = 0.154 in

LI M I T ED B Y : DESIGN PRESSURE CA = CORROSION ALLOWANCE = 0.000 in

2. INITIA L TEST P RESSURE (NEW P IP E): 2250 psig M AXIM UM ALLOWABLE TEST PRESSURE:
BY/DATE
OTHER

2.1 FOR ASM E 600# FLANGES (GR 1.7)PER ASM E B16.5 2250 psig
2 X 0.90 X 65000 X 0.154
PT = = 7587 psig
2.375

7587 psig > 2250 psig

OPERATIONS/DATE

07/15/2019

3. INITIA L TEST P RESSURE LIM ITED B Y:

MMM
REVIEW FOR KEY DRAWINGS
REQUIRED (SAUDI ARAMCO)

FLANGE

4. SYSTEM M A X. OP ERA TING P RESSURE, M A OP :

M AOP = 1300 psig

5. SA FETY VA LVE SET P RESSURE:

CONST. AGENCY/DATE

07/15/2019

1.05 X PT 2363 psig

MTG

6. Tmin WA LL THICKNESS:

1300 X 2.375 M INIM UM REQUIRED WALL THICKNESS,

M AOP X D
Tm = = 0.033 inch Tm = BASED ON SYSTEM M AOP & DESIGN
2 X 65000 X 0.72 2 X SM YS X F FACTOR
CERTIFIED/DATE

07/15/2019

T CA = T CA = T n - T m WALL THICKNESS IN EXCESS OF T m

OAB

0.154 - 0.033 = 0.121 inch

DESIGN CERTIFICATION
(DESIGN AGENCY)

SELECTED WALL THICKNESS = T n = 0.154 inch

ENGG./DATE

07/15/2019
BEK
AND CERTIFICATION REQUIREMENTS, PER SAEP-334, UNDER
IS COVERED, FOR ALL APPROVAL
REVISION VALIDATION

DRAWING COMPLETION CERTIFICATE NO.

10-02454-0003
A THIS REVISION NO.

SIS FOR 36" TRUNKLINE (M93-L-0002) DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT.NO REV.NO.

SIS:MAINLINE PIPING FROM WATER SUPPLY FACILITIES TO UTILITY UNITS SIS

TANAJIB WATER SUPPLY FACILITIES M93 A RE-789974 006 A
TANAJIB SAUDI ARABIA
EKRD/2616-1110.XLS
Saudi Aramco 5645-2-ENG (11/2010)

SAUDI ARABIAN OIL COMPANY

THIS REVISION IS NOT TO BE USED FOR

CONSTRUCTION UNTIL CERTIFIED AND
SAFETY INSTRUCTION SHEET FOR CROSS COUNTRY PIPELINE - CRITICAL PIPING
1 PIPELINE NAME 2 START POINT 3 END POINT 4 SERVICE 5 VALVE OPER. DIAGRAM 6 YR. BUILT

36"-SW-0648-6LE0W04 MARJAN WELL SITE 1& 2 M97-L-0001 SUPPLY WATER RA-640540.001

DATED
7 EQUIPMENT NAME M97-L-0001 EQUIPMENT NAME
ISSUED FOR 90% REVIEW
REVISION DESCRIPTION

8 LOCATION (@ Km.) TANAJIB UTILITY UNIT LOCATION (@ Km.)

9 SECTION SECTION

10 EQUIP. CATEGORY PIPELINE EQUIP. CATEGORY

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
11 SIZE in. 36 in. 4 in. 2 in. SIZE in.

12 W.T. in. 0.625 0.188 0.154 W.T. in.

13 MATERIAL CS CS CS MATERIAL
PIPE

PIPE
14 WELD TYPE SAW SMLS SMLS WELD TYPE
07/15/2019

15 SPEC. / GR. X70 X65 X65 SPEC. / GR.

DATE

10-02454-0003

16 COATING TYPE FBE FBE FBE COATING TYPE

JOB ORDER/EWO NO.

EQUIPMENT DATA

17 RATING MATCH TO PIPE MATCH TO PIPE MATCH TO PIPE RATING

FITTING

FITTING
18 FACING BW BW BW FACING
REV. NO.

19 MATERIAL CS CS CS MATERIAL
A

20 SPEC. / GR. A860 WPHY-70 A860 WPHY-70 A860 WPHY-70 SPEC. / GR.

21 REMARKS REMARKS
BY/DATE
OTHER

OPERATIONS/DATE

07/15/2019

22 FLANGE RATING 600 600 600 FLANGE RATING

MMM

23 FLANGE FACING RF RF RF FLANGE FACING

24 FLANGE MAT'L SPECIFICATION A859 A CL2 A859 A CL2 A859 A CL2 FLANGE MAT'L SPECIFICATION
REVIEW FOR KEY DRAWINGS
REQUIRED (SAUDI ARAMCO)

25 M.A.O.P. 1367 PSIG, LIMITED BY: VALVE M.A.O.P. PSIG, LIMITED BY:
26 DESIGN FACTOR 0.72 DESIGN FACTOR
27 DESIGN TEMPERATURE: 194 oF DESIGN TEMPERATURE: (°F) oF
28 TEST PRESSURE 2188 PSIG TEST PRESSURE PSIG
OPERATING LIMITS
CONST. AGENCY/DATE

INITIAL INITIAL
PRESSURE 29 TEST DATE PRESSURE TEST DATE
07/15/2019

TEST TEST
30 LIMITED BY PIPE LIMITED BY
MTG

31 TEST PRESSURE PSIG TEST PRESSURE PSIG

REVALIDATION 32 TEST DATE REVALIDATION TEST DATE

33 LIMITED BY LIMITED BY
34 SYSTEM M.A.O.P. 1300 PSIG SYSTEM M.A.O.P. PSIG

35 LIMITED BY * LIMITED BY

36 SAFETY VALVE SET PRESS. 2297 PZV SAFETY VALVE SET PRESS. PZV
CERTIFIED/DATE

07/15/2019

DES THK @ 37 PIPE SIZE 36 in. 4 in. 2 in. DES THK @ PIPE SIZE in. in. in.
OAB

SYSTEM MAOP 38 PIPE Tm 0.464 in. 0.063 in. 0.033 in. SYSTEM MAOP PIPE Tm in. in. in.
DESIGN CERTIFICATION
(DESIGN AGENCY)

& DES TEMP 39 PIPE Tca 0.161 in. 0.126 in. 0.121 in. & DES TEMP PIPE Tca in. in. in.
40 OSI DATA POINTS OSI DATA POINTS
OSI DATA POINT INFO.

SEQ. DATE WT(in). DATE WT(in). DATE WT(in). SEQ. DATE WT(in). DATE WT(in). DATE WT(in).

1 1
ENGG./DATE

07/15/2019

2 2
BEK

3 3

4 4

5 5

6 6

41 REMARKS REMARKS

* LIMITED BY DESIGN CONDITION

IS COVERED, FOR ALL APPROVAL

AND CERTIFICATION REQUIREMENTS, PER SAEP-334, UNDER

REVISION VALIDATION

10-02454-0003

42 REFERENCE DWGS REFERENCE DWGS

DRAWING COMPLETION CERTIFICATE NO.

P&ID : RA-640540.001

PIPELINE MATERIAL SPECIFICATION: RE-789964

HYDROSTATIC TEST DRAWING : RA-789962.002

A THIS REVISION NO.

SIS FOR 36" TRUNKLINE (M97-L-0001) DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO

SIS:MAINLINE PIPING FROM WATER SUPPLY FACILITIES TO UTILITY UNITS SIS

TANAJIB UTILITIES UNIT M97 A RE-789974 007 A
TANAJIB SAUDI ARABIA
EKRD/5645-2-1110.XLS

150 RF
Saudi Aramco 2616-ENG (11/2010)

SAUDI ARABIAN OIL COMPANY

UNTIL CERTIFIED AND DATED

THIS REVISION IS NOT TO BE
USED FOR CONSTRUCTION NOTE: THE INTENT OF THIS SHEET IS TO SHOW ALL CALCULATIONS AND REFERENCE DOCUMENTS
ISSUED FOR 90% REVIEW

THAT WERE USED TO GENERATE THE SIS SHEET.

REVISION DESCRIPTION

1. FOR 36" 0.625" WT. API 5L - GR X70 SAW PIPE: MAXIMUM ALLOWABLE OPERATING PRESSURE (MAOP):

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
1.1 MAOP FLANGE = 1500 psig (600# Class @ 194 °F, ASME B16.47)

2 X 70000 X 0.625 X 0.72 (Material group 1.7)

MAOP PIPE = = 1750 psig
36.000 1.2 MAOP PIPE = 2 X SMYS X TCOR X F
D (B16.34, Material group 1.1)
1.3 MAOP VALVES = 1367 psig

WHERE:
1750 psig > 1500 psig > 1367 psig DESIGN PRESSURE = 1300 psi
07/15/2019

THEREFORE MAOP AT DESIGN FACTOR: 1367 psig SMYS = SPECIFIED MIN YIELD STRENGTH = 70000 psi
DATE

10-02454-0003

LIMITED BY: VALVE Tn= NOMINAL (SELECTED) WALL THICKNESS = 0.625 in

JOB ORDER/EWO NO.

F = DESIGN FACTOR = 0.72

D = OUTSIDE DIAMETER OF PIPE = 36.000 in

REV. NO.

1367 psig > 1300 psig dT = DESIGN TEMP. - MIN TIE-IN TEMP. 194 - 70 = 124 °F
TCOR = CORRODED WALL THICKNESS = Tn - CA = 0.625 in
A

THEREFORE SYSTEM MAOP: 1300 psig

LIMITED BY: DESIGN PRESSURE CA = CORROSION ALLOWANCE = 0.000 in

2. INITIAL TEST PRESSURE (NEW PIPE): 2188 psig MAXIMUM ALLOWABLE TEST PRESSURE:
BY/DATE
OTHER

2.1 FOR ASME 600# FLANGES (GR 1.7)PER ASME B16.47 2250 psig
2 X 0.90 X 70000 X 0.625
PT = = 2188 psig
36.000

2250 psig > 2188 psig

OPERATIONS/DATE

07/15/2019

3. INITIAL TEST PRESSURE LIMITED BY:

MMM
REVIEW FOR KEY DRAWINGS
REQUIRED (SAUDI ARAMCO)

PIPE

4. SYSTEM MAX. OPERATING PRESSURE, MAOP:

MAOP = 1300 psig

5. SAFETY VALVE SET PRESSURE:

CONST. AGENCY/DATE

07/15/2019

1.05 X PT 2297 psig

MTG

6. Tmin WALL THICKNESS:

1300 X 36.000 MINIMUM REQUIRED WALL THICKNESS,

MAOP X D
Tm = = 0.464 inch Tm = BASED ON SYSTEM MAOP & DESIGN
2 X 70000 X 0.72 2 X SMYS X F FACTOR
CERTIFIED/DATE

07/15/2019

TCA = 0.625 - 0.464 = 0.161 inch TCA = Tn - Tm WALL THICKNESS IN EXCESS OF Tm

OAB
DESIGN CERTIFICATION

SELECTED WALL THICKNESS = Tn = 0.625 inch

(DESIGN AGENCY)

ENGG./DATE

07/15/2019
BEK
AND CERTIFICATION REQUIREMENTS, PER SAEP-334, UNDER
IS COVERED, FOR ALL APPROVAL
REVISION VALIDATION

DRAWING COMPLETION CERTIFICATE NO.

10-02454-0003
A
THIS REVISION NO.

SIS FOR 36" TRUNKLINE (M97-L-0001) DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT.NO REV.NO.

SIS:MAINLINE PIPING FROM WATER SUPPLY FACILITIES TO UTILITY UNITS SIS

TANAJIB UTILITIES UNIT M97 A RE-789974 008 A
TANAJIB SAUDI ARABIA
EKRD/2616-1110.XLS
Saudi Aramco 2616-ENG (11/2010)

SAUDI ARABIAN OIL COMPANY

UNTIL CERTIFIED AND DATED

THIS REVISION IS NOT TO BE
USED FOR CONSTRUCTION
N OT E: T H E IN T E N T O F T H IS S H E E T IS T O S H O W A LL C A LC ULA T IO N S A N D R E F E R E N C E D O C UM E N T S
ISSUED FOR 90% REVIEW

T H A T WE R E US E D T O G E N E R A T E T H E S IS S H E E T .
REVISION DESCRIPTION

1. FOR 4.5" 0.188" WT. A P I 5L - GR X65 SM LS P IP E: M AXIM UM ALLOWABLE OPERATING PRESSURE (M AOP):

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
1.1 M AOP FLANGE = 1500 psig (600# Class @ 194 °F, ASM E B16.5)

2 X 65000 X 0.188 X 0.72 (M at erial group 1.7)

M AOP PIPE = = 3910 psig
4.500 1.2 M AOP PIPE = 2 X SM YS X T COR X F
D ( B16.34, M at erial group 2.8)
1.3 M AOP VALVES = 1490 psig

WHERE:

3910 psig > 1500 psig > 1490 psig DESIGN PRESSURE = 1300 psi
07/15/2019

THEREFORE M AOP AT DESIGN FACTOR: 1490 psig SM YS = SPECIFIED M IN YIELD STRENGTH = 65000 psi
DATE

10-02454-0003

LI M I T ED B Y : VALVE Tn= NOM INAL (SELECTED) WALL THICKNESS = 0.188 in

JOB ORDER/EWO NO.

F = DESIGN FACTOR = 0.72

D = OUTSIDE DIAM ETER OF PIPE = 4.500 in

REV. NO.

1490 psig > 1300 psig dT = DESIGN TEM P. - M IN TIE-IN TEM P. 194 - 70 = 124 °F
A

THEREFORE SYSTEM M AOP: 1300 psig TCOR = CORRODED WALL THICKNESS = T n - CA = 0.188 in

LI M I T ED B Y : DESIGN PRESSURE CA = CORROSION ALLOWANCE = 0.000 in

2. INITIA L TEST P RESSURE (NEW P IP E): 2250 psig M AXIM UM ALLOWABLE TEST PRESSURE:
BY/DATE
OTHER

2.1 FOR ASM E 600# FLANGES (GR 1.7)PER ASM E B16.5 2250 psig
2 X 0.90 X 65000 X 0.188
PT = = 4888 psig
4.500

4888 psig > 2250 psig

OPERATIONS/DATE

07/15/2019

3. INITIA L TEST P RESSURE LIM ITED B Y:

MMM
REVIEW FOR KEY DRAWINGS
REQUIRED (SAUDI ARAMCO)

FLANGE

4. SYSTEM M A X. OP ERA TING P RESSURE, M A OP :

M AOP = 1300 psig

5. SA FETY VA LVE SET P RESSURE:

CONST. AGENCY/DATE

07/15/2019

1.05 X PT 2363 psig

MTG

6. Tmin WA LL THICKNESS:

1300 X 4.500 M INIM UM REQUIRED WALL THICKNESS,

M AOP X D
Tm = = 0.063 inch Tm = BASED ON SYSTEM M AOP & DESIGN
2 X 65000 X 0.72 2 X SM YS X F FACTOR
CERTIFIED/DATE

07/15/2019

T CA = 0.188 - 0.063 = 0.126 inch T CA = T n - T m WALL THICKNESS IN EXCESS OF T m

OAB
DESIGN CERTIFICATION
(DESIGN AGENCY)

SELECTED WALL THICKNESS = T n = 0.188 inch

ENGG./DATE

07/15/2019
BEK
AND CERTIFICATION REQUIREMENTS, PER SAEP-334, UNDER
IS COVERED, FOR ALL APPROVAL
REVISION VALIDATION

DRAWING COMPLETION CERTIFICATE NO.

10-02454-0003
A THIS REVISION NO.

SIS FOR 36" TRUNKLINE (M97-L-0001) DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT.NO REV.NO.

SIS:MAINLINE PIPING FROM WATER SUPPLY FACILITIES TO UTILITY UNITS SIS

TANAJIB UTILITIES UNIT M97 A RE-789974 009 A
TANAJIB SAUDI ARABIA
EKRD/2616-1110.XLS
Saudi Aramco 2616-ENG (11/2010)

SAUDI ARABIAN OIL COMPANY

UNTIL CERTIFIED AND DATED

THIS REVISION IS NOT TO BE
USED FOR CONSTRUCTION
N OT E: T H E IN T E N T O F T H IS S H E E T IS T O S H O W A LL C A LC ULA T IO N S A N D R E F E R E N C E D O C UM E N T S
ISSUED FOR 90% REVIEW

T H A T WE R E US E D T O G E N E R A T E T H E S IS S H E E T .
REVISION DESCRIPTION

1. FOR 2.375" 0.154" WT. A P I 5L - GR X65 SM LS P IP E: M AXIM UM ALLOWABLE OPERATING PRESSURE (M AOP):

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
1.1 M AOP FLANGE = 1500 psig (600# Class @ 194 °F, ASM E B16.5)

2 X 65000 X 0.154 X 0.72 (M at erial group 1.7)

M AOP PIPE = = 6069 psig
2.375 1.2 M AOP PIPE = 2 X SM YS X T COR X F
D ( B16.34, M at erial group 2.8)
1.3 M AOP VALVES = 1490 psig

WHERE:

6069 psig > 1500 psig > 1490 psig DESIGN PRESSURE = 1300 psi
07/15/2019

THEREFORE M AOP AT DESIGN FACTOR: 1490 psig SM YS = SPECIFIED M IN YIELD STRENGTH = 65000 psi
DATE

10-02454-0003

LI M I T ED B Y : VALVE Tn= NOM INAL (SELECTED) WALL THICKNESS = 0.154 in

JOB ORDER/EWO NO.

F = DESIGN FACTOR = 0.72

D = OUTSIDE DIAM ETER OF PIPE = 2.375 in

REV. NO.

1490 psig > 1300 psig dT = DESIGN TEM P. - M IN TIE-IN TEM P. 194 - 70 = 124 °F
A

THEREFORE SYSTEM M AOP: 1300 psig TCOR = CORRODED WALL THICKNESS = T n - CA = 0.154 in

LI M I T ED B Y : DESIGN PRESSURE CA = CORROSION ALLOWANCE = 0.000 in

2. INITIA L TEST P RESSURE (NEW P IP E): 2250 psig M AXIM UM ALLOWABLE TEST PRESSURE:
BY/DATE
OTHER

2.1 FOR ASM E 600# FLANGES (GR 1.7)PER ASM E B16.5 2250 psig
2 X 0.90 X 65000 X 0.154
PT = = 7587 psig
2.375

7587 psig > 2250 psig

OPERATIONS/DATE

07/15/2019

3. INITIA L TEST P RESSURE LIM ITED B Y:

MMM
REVIEW FOR KEY DRAWINGS
REQUIRED (SAUDI ARAMCO)

FLANGE

4. SYSTEM M A X. OP ERA TING P RESSURE, M A OP :

M AOP = 1300 psig

5. SA FETY VA LVE SET P RESSURE:

CONST. AGENCY/DATE

07/15/2019

1.05 X PT 2363 psig

MTG

6. Tmin WA LL THICKNESS:

1300 X 2.375 M INIM UM REQUIRED WALL THICKNESS,

M AOP X D
Tm = = 0.033 inch Tm = BASED ON SYSTEM M AOP & DESIGN
2 X 65000 X 0.72 2 X SM YS X F FACTOR
CERTIFIED/DATE

07/15/2019

T CA = 0.154 - 0.033 = 0.121 inch T CA = T n - T m WALL THICKNESS IN EXCESS OF T m

OAB
DESIGN CERTIFICATION
(DESIGN AGENCY)

SELECTED WALL THICKNESS = T n = 0.154 inch

ENGG./DATE

07/15/2019
BEK
AND CERTIFICATION REQUIREMENTS, PER SAEP-334, UNDER
IS COVERED, FOR ALL APPROVAL
REVISION VALIDATION

DRAWING COMPLETION CERTIFICATE NO.

10-02454-0003
A THIS REVISION NO.

SIS FOR 36" TRUNKLINE (M97-L-0001) DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT.NO REV.NO.

SIS:MAINLINE PIPING FROM WATER SUPPLY FACILITIES TO UTILITY UNITS SIS

TANAJIB UTILITIES UNIT M97 A RE-789974 010 A
TANAJIB SAUDI ARABIA
EKRD/2616-1110.XLS