PRODUCTS MANUAL

Product Type： Switching Power Supply

Model Name： H1M SERIES

Rev.:A1

P/N:
 INDEX

1.1 Introduction page 2

1.2 Packing page 2
1.3 Model Designation page 2
1.4 Features page 3
1.5 Pre-Installation page 3
1.6 Pin Assignment page 4~5
1.7 Specifications page 6 ~7
1.8 Operational Procedure page 8
1.9 Troubleshooting & Maintenance page 9
1.10 Technical Support Page 10

1
1.1 Introduction

First of all, thank you for purchasing H1M Series –power supply.

The H1M Series power supply offers a maximum 800 watts of output power.

The power unit’s size is compact and both power modules built two interior
40X28 m/m ball bearing DC fans for H1M-5xx0V, two interior 38X28 m/m ball
bearing DC fans for H1M-5xx7V Total set has designed with 5 outputs including
+12V, +5V, +3.3V, -12V, & +5VSB circuits

To really discover the power and easy in using these products, we recommend
that you read through this manual carefully.

1.2 Packing
Your H1M box package should consist of the following:

(A) H1M *1
(B) Accessory pack *1

1.3 Model Designation

Model number identification:

H1M-5xxyV

H1M --- Model name

5 --- For 6 DC outputs (5V/12V/-12V/3.3V/5VSB) for
ATX12V / EPS12V Spec.
xx --- Total output power, 60(means 600W), 70(means 700W),
80 (means 800W)
y --- 0 = Physical dimension : 250mm (D) x 100mm (W) x 40.5mm (H)
7 = Physical dimension : 275mm (D) x 100mm (W) x 40.5mm (H)
V --- High efficiency.

2
1.4 Features
 Dimension :H1M -5xx0V = 250mm(D)×100mm(W)×40.5mm(H)
H1M-5xx7V = 275mm(D)×100mm(W)×40.5mm(H)
 EN 61000-4-2(ESD) Criterion B, ±4KV by contact, ±8KV by air.
All circuits had been designed in the power module
 EN 61000-4-4(EFT) Criterion B, ±1KV.
 EN 61000-4-5(SURGE) Criterion B, Line-Line ±1KV, Line-Earth ±2KV.
 Remote sensing design
 Meet FCC, CISPR EMI regulation
 Space save design
 Two 40X28 m/m ball bearing DC fan for H1M-5xx0V
 Two 38X28 m/m ball bearing DC fan for H1M-5xx7V

1.5 Pre-Installation
Before installing the H1M unit into the system chassis, please review the
following drawings page 6 ~ 8 and find out the best way to match them.

3
1.6 Pin Assignment
Always check the socket and pin assignment (for devices such as motherboard, Hard Disk etc.)
before connecting the two heads.

4
5
1.7 Specifications
INPUT CHARACTERISTICS: H1M-5600/5700/5800V

A、INPUT CHARACTERISTICS：
1、VOLTAGE：90～264VAC FULL RANGE
2、FREQUENCY： 47～63HZ
3、INPUT CURRENT：10.0A (RMS) FOR 115 VAC
5.0A (RMS) FOR 230 VAC
4、INRUSH CURRENT：30A MAX. FOR 115 VAC
60A MAX. FOR 230 VAC
AT 25 ℃

B、OUTPUT CHARACTERISTICS：
OUTPUT OUTPUT CURRENT REGULATION OUTPUT RIPPLE &
VOLTAGE MIN. MAX. PEAK. LOAD LINE NOISE MAX. [P-P]
+5V 0.5A 25A ±5% ±1% 50mV
+12V 2A 48A/48A/57A ±5% ±1% 120mV
-12V 0A 0.8A ±5% ±1% 120mV
+3.3V 0.5A 25A ±5% ±1% 50mV
+5VSB 0.1A 3.5A ±5% ±1% 50mV

REMARK: THE OUTPUT CURRENT OF 5V & 3.3V NOT EXCEED 40A

C、SPECIFICATION
1、TEMPERATURE RANGE：OPERATING 0℃～40℃
2、HOLD UP TIME：16mS MINIMUM AT FULL LOAD & NOMINAL INPUT VOLTAGE
3、DIELECTRIC WITHSTAND：INPUT/OUTPUT 1500 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
4、EFFICIENCY：typical 80-83% at 25℃115V FULL LOAD
5、POWER GOOD SIGNAL：ON DELAY 100mS TO 500mS，OFF DELAY 1mS
6、OVERLOAD PROTECTION：130% +/- 20%
7、OVER VOLTAGE PROTECTION：+5V→5.6V～6.5V, 3.3V→3.6V～4.3V, +12V→13.2V～15V
8、SHORT CIRCUIT PROTECTION：+5V、+12V、-12V、+3.3V、+5VSB
9、EMI NOISE FILTER : FCC CLASS B , CISPR22 CLASS B
10、SAFETY : UL 62368, CSA UL62368, TUV IEC 62368
11、REMOTE ON/OFF CONTROL
THE POWER SUPPLY SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL
DISABLE/ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STAND BY).
AS LOGIC LEVEL IS LOW，OUTPUTS VOLTAGE WERE ENABLE，
AS LOGIC LEVEL IS HIGH，OUTPUTS VOLTAGE WERE DISABLE.
12、COOLING : TOW 48*28mm DC FAN
13、DIMENSION： H1M-5xx0V=250mm*100mm*40.5mm (D*W*H)
14、MEET EN-61000-3-2 CLASS D

6
INPUT CHARACTERISTICS: H1M-5607/5707/5807V

A、INPUT CHARACTERISTICS：
1、VOLTAGE：90～264VAC FULL RANGE
2、FREQUENCY： 47～63HZ
3、INPUT CURRENT：10.0A (RMS) FOR 115 VAC
5.0A (RMS) FOR 230 VAC
4、INRUSH CURRENT：30A MAX. FOR 115 VAC
60A MAX. FOR 230 VAC
AT 25 ℃

B、OUTPUT CHARACTERISTICS：
OUTPUT OUTPUT CURRENT REGULATION OUTPUT RIPPLE &
VOLTAGE MIN. MAX. PEAK. LOAD LINE NOISE MAX. [P-P]
+5V 0.5A 25A ±5% ±1% 50mV
+12V 2A 48A/48A/57A ±5% ±1% 120mV
-12V 0A 0.8A ±5% ±1% 120mV
+3.3V 0.5A 25A ±5% ±1% 50mV
+5VSB 0.1A 3.5A ±5% ±1% 50mV

REMARK: THE OUTPUT CURRENT OF 5V & 3.3V NOT EXCEED 40A

C、 SPECIFICATION
1、 TEMPERATURE RANGE：OPERATING 0℃～40℃
2、 HOLD UP TIME：16mS MINIMUM AT FULL LOAD & NOMINAL INPUT VOLTAGE
3、DIELECTRIC WITHSTAND：INPUT/OUTPUT 1500 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
4、 EFFICIENCY：typical 80-83% at 25℃115V FULL LOAD
5、 POWER GOOD SIGNAL：ON DELAY 100mS TO 500mS，OFF DELAY 1mS
6、 OVERLOAD PROTECTION：130% +/- 20%
7、 OVER VOLTAGE PROTECTION：+5V→5.6V～6.5V, 3.3V→3.6V～4.3V, +12V→13.2V～15V
8、 SHORT CIRCUIT PROTECTION：+5V、+12V、-12V、+3.3V、+5VSB
9、 EMI NOISE FILTER : FCC CLASS B , CISPR22 CLASS B
10、 SAFETY : UL 62368, CSA UL62368, TUV IEC 62368
11、REMOTE ON/OFF CONTROL
THE POWER SUPPLY SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL
DISABLE/ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STAND BY).
AS LOGIC LEVEL IS LOW，OUTPUTS VOLTAGE WERE ENABLE，
AS LOGIC LEVEL IS HIGH，OUTPUTS VOLTAGE WERE DISABLE.
12、 COOLING : TOW 38*28mm DC FAN
13、 DIMENSION： H1M-5xx7V=275mm*100mm*40.5mm (D*W*H)
14、MEET EN-61000-3-2 CLASS D

7
1.8 Operational Procedure

1. When removing four attached screws to install this product, please make sure not
removing fan or case screws by mistake.

2. Tighten four screws onto the computer case and double check for stability.

3. Check product specifications and calculate actual current requirements of each DC

voltage. Make sure these requirements fall within the minimum and maximum range of
power supply. If the current requirements are below the minimum load spec., the power
supply may not start up. If the current requirements are over the maximum load spec.,
our over protection circuitry will latch and shutdown the power supply.

4. Plug in power cord to the inlet of power supply.

 Active Power Factor Correction (PFC) function is available for all power supply
models listed in this manual. The PFC function ensures maximum efficiency of
power usage to preserve energy and lower your electrical bills. It also
automatically adapts to a very wide range of AC line voltage: 100V to 240V AC.
(There are no manual switches for you to select AC input). This unique design
ensures you can use our power supplies anywhere in the world.

5. You can start up the power supply remotely by using “Remote on”.

8
1.9 Troubleshooting & Maintenance

SYMPTOM COUNTERMEASURE
No power?  After plug main connector, such as 24-pin or 20-pin and aux.
connectors if needed, to motherboard socket, make sure AC
power cord gets AC line source that is on wall outlet, to this
product power supply. If AC power cord gets AC line source
through power bar or UPS, turn on these devices first.

 Boot system from computer case I/O.

 Check product specifications and calculate actual current

requirements of each DC voltage. Make sure these requirements
fall within the minimum and maximum range of power supply.
(i) If the current requirements are below the minimum load
spec., the power supply may not start up. Increase load. (ii) If
the current requirements are over the maximum load spec., our
over protection circuitry will latch and shutdown the power
supply. Reduce load or use larger capacity power supply.

 The power supply could be latched by self-protection function

(e.g. “over voltage”, “over current”, “overload”). Remove the
power cord, wait for 20 seconds or more to discharge its
electricity, then plug in the power cord again, try to restart the
computer.

9
1.10 Technical Support

To best serve our customers, there are several services available to suite your needs:

1. For detailed products specification: please visit www.zippy.com

2. For technical enquiries: please send e-mail to [email protected]

3. For RMA service: please prepare following items before applying RMA.
 Product barcode number on the label of power supply housing
 Product part number (P/N)
 Product model
 Detailed description of problems
Note:
Different distributors or resellers have their specific RMA terms and conditions;
please contact them for detailed information.

4. Please feel free to contact us via e-mail should you encounter any technical
problems beyond the scope of this user manual. Please visit www.zippy.com for
more detailed information.

10
 The “RELIABILITY “ solution to E-application

新巨企業股份有限公司

ZIPPY TECHNOLOGY CORP.

POWER DIVISION
HEADQUARTERS
10F, NO. 50, MINQUAN RD., XINDIAN DIST.,
NEW TAIPEI CITY 231, TAIWAN
TEL: 886-2-29188512 FAX: 886-2-29134969
WEB SITE: http://www.zippy.com.tw EMAIL: [email protected]

FACTORY
4F, No. 48, WUQUAN Rd., WUGU Dist.,
NEW TAIPEI CITY 248, TAIWAN
TEL: 886-2-22996968 FAX: 886-2-22991229 / 2299-5005
WEB SITE: http://www.zippy.com.tw EMAIL: [email protected]

ZIPPY USA INC.

1 Morgan, Irvine CA 92618, USA
TEL：+1-949-3669525 │ FAX：+1-949-3669526
E-mail: [email protected]

ZIPPY TECHNOLOGY EUROPE GMBH

GIESENHEIDE 23, 40724 HILDEN, GERMANY
TEL：+49-(0)2103-57601-00 │ FAX：+49-(0)2103-57601-29
E-mail: [email protected]

G-BRIM INTERNATIONAL INC.

2310, 2311, Building G, Hualian City Panorama, District 27,
 Dalang community, Xinan Strett, Baoan District, Shenzhen,
China 518101
TEL：+86-755-2977-8708 │ FAX：+86-755-2977-8713
E-mail: [email protected]

Note:
*The description stated herein is subject to change without prior notice.
*All brand names and trademarks are the property of their respective owners.