Scribd Logo
Upload

Welcome to Scribd!

  • 23 views

    BearingWall ICF

    Uploaded by

    Ahmed Medo
    1. This document summarizes the design of an insulated concrete form (ICF) bearing wall based on ACI 318-19 and 2021 IBC code standards. 2. Key inputs include a factored out-of-plane moment of 2.3 ft-kips/ft, a factored axial load of 20 kips/ft, and a factored shear load of 0.98 kips/ft. 3. The analysis checks the axial and flexure capacity and shear capacity of the wall. Both checks are satisfactory, indicating the wall design is adequate.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd

    BearingWall ICF

    Uploaded by

    Ahmed Medo
    23 views1 page
    1. This document summarizes the design of an insulated concrete form (ICF) bearing wall based on ACI 318-19 and 2021 IBC code standards. 2. Key inputs include a factored out-of-plane moment of 2.3 ft-kips/ft, a factored axial load of 20 kips/ft, and a factored shear load of 0.98 kips/ft. 3. The analysis checks the axial and flexure capacity and shear capacity of the wall. Both checks are satisfactory, indicating the wall design is adequate.

    Copyright

    © © All Rights Reserved

    Available Formats

    XLSX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. This document summarizes the design of an insulated concrete form (ICF) bearing wall based on ACI 318-19 and 2021 IBC code standards. 2. Key inputs include a factored out-of-plane moment of 2.3 ft-kips/ft, a factored axial load of 20 kips/ft, and a factored shear load of 0.98 kips/ft. 3. The analysis checks the axial and flexure capacity and shear capacity of the wall. Both checks are satisfactory, indicating the wall design is adequate.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    23 views1 page

    BearingWall ICF

    Uploaded by

    Ahmed Medo
    1. This document summarizes the design of an insulated concrete form (ICF) bearing wall based on ACI 318-19 and 2021 IBC code standards. 2. Key inputs include a factored out-of-plane moment of 2.3 ft-kips/ft, a factored axial load of 20 kips/ft, and a factored shear load of 0.98 kips/ft. 3. The analysis checks the axial and flexure capacity and shear capacity of the wall. Both checks are satisfactory, indicating the wall design is adequate.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    of 1

    PROJECT : PAGE :

    CLIENT : DESIGN BY :
    JOB NO. : DATE : REVIEW BY :
    Bearing Wall Design of Insulated Concrete Form (ICF) Based on ACI 318-19 & 2021 IBC

    DESIGN CRITERIA
    1. Insulated Concrete Form (ICF) can be waffle grid core, and screen grid core, and/or even flat wall core. This design method is
    based on linear distribution of strain, which only consider the concrete strength of screen grid core conservatively.
    2. Since it is difficult to design ICF wall tension-controlled (ACI 318-19 11.8.1.1) only, this software does NOT use the method of
    Alternative Design of Slender Walls (ACI 318-19 11.8), so no P- D effects have to be applied (ACI 318-19 11.8.1.1).

    INPUT DATA & DESIGN SUMMARY


    FACTORED MAX OUT-OF-PLANE SECTION MOMENT (from wind or seismic lateral loads, the max value of wmaxH2/8 may be input).
    Mu = 2.3 ft-kips / ft, (10.2 kN-m / m)
    FACTORED AXIAL LOAD (con-currently at the same section with M u).
    Pu = 20 kips/ft, (291.7 kN/m)
    FACTORED SHEAR LOAD Vu = 0.98 kips/ft, (14.3 kN/m)

    CONCRETE STRENGTH fc' = 3 ksi, (21 MPa)


    REBAR YIELD STRESS fy = 60 ksi, (414 MPa)

    WALL CORE SIZE b = 6 in, (152 mm)


    h = 12 in, (305 mm) THE WALL DESIGN IS ADEQUATE.
    VERTICAL REINFORCEMENT (A s) WITH CORE SPACING
    # 5 @ 24 in. (610 mm), o.c.
    As LOCATION (1=at middle, 2=at each face) 1 at middle

    ANALYSIS
    CHECK AXIAL & FLEXURE CAPACITY
    rProvD = 0.008611 < rMAX = 0.0800 (tension face only, ACI 318-19 22.2.3.1 or 10.6.1.1)
    [Satisfactory] > rMIN = 0.0015 (tension face only, ACI 318-19 9.6.1 or 11.6.1)

    120      2
      f C'  2   c     c   , for 0   c   o  s E s , for  s   ty
    e
    fC    o    o   , f S
    100  '
     f y , for  s   ty
      e f C , for  c   o

    80 
    2 e f C
    '
     fy  ty , for compression controlled
    o  ,  ty  , t  
    Ec Es  ty  0.003 , for tension controlled
    f Pn (k) 60 '
    E c  57 f C , E s  29000ksi ,  e  0.85 ,  cu  0.003

    40 Note:
    1. Between compression & tension controlled is
    20 Transition, which the f should be by linear
    interpolation. (ACI 318-19 Tab. 21.2.2 & Fig. R10.4.2.1)
    0
    2. ACI 318-19 changed f (Fig.R21.2.2b) and keeps
    0 1 2 3 4 5 6
    be (22.2.2.4.1) and ecu (Fig. R21.2.2a) the same.
    -20
    Solid Black Line - Tension Controlled f Mn (ft-k) But AISC 360/341-16 has different f (0.9 only) and
    Solid Red Line - Transition be (1.0 or 0.7).

    Dash Line - Compression Controlled f Mn = 4.64 ft-kips @ Pu = 20.00 kips


    > Mu = 2.30 ft-kips [Satisfactory]
    CHECK SHEAR CAPACITY (ACI 318-19 22.5.5)

    '
     V n  2 bd fc = 1.48 kips / ft > Vu [Satisfactory]

    You might also like