Charging Discharging

INSTRUCTION MANUAL
FOR
CHARGING & DISCHARGING OF CONDENSOR
'MARS' made Charging & Discharging of condenser has been designed to note the
charge & discharge time of condenser for different sets of resistances & capacitors.
The instrument comprises of the following built in parts:-
1. Variable DC power supply of 0-15V available at sockets provided on front panel.
2. Two DPM's are provided on front panel to note down voltage & current during
charging & discharging.
3. Four sets of resistance & capacitor connected inside & connected brought out at
terminals provided on the front panel.
4. One charging and discharging switch is provided on front panel to charge &
discharge the condenser respectively
THEORY
A capacitor is also called a condenser. It is a device which is designed for the storage of
charge. It consists of two metallic plates separated by an insulating material called the
dielectric. It has been observed experimentally that the quantity of charge stored in a
capacitor is directly proportional to the potential difference applied across its plates i.e.
QαV
Where Q is the charge stored on the plates of a capacitor and v is the potential difference
applied.
Or Q=CV
Where C is the constant of proportionately and is called the capacity or capacitance of the
condenser.
Therefor
C=Q/ V
Capacity of a condenser is defined as the amount of charge required to establish a unit

potential difference between the plates. S.I. Unit of capacitance is farad, abbreviated as
'F'.
A capacitor does not allow the passage of direct current through it. If a DC source of e.m.f
is applied across its plates, it takes up a small charge and a displacement current is set up
in the dielectric between the plates. The plates acquire more and more charge from the
battery. Further addition of m ore charge from the battery on the plates is opposed
because a back e.m.f. is set up by the condenser during the process of charging. At the
same time charge given by battery simply keeps on getting stored on the plates of the
capacitor but does not flow through the dielectric. The current which flows through the
dielectric of the capacitor is only the displacement current. The flow of charge through the
capacitor with a resistance in its series constitutes a varying current. The charging of
capacitor is given by the equation
Q=Q 0 ( 1−e−t / RC ) (i)
Where Q is the charge on plates at a time t
The discharging is given by the relation
Q=Q 0 e−t / RC (ii)
The above two equations are exponential in character.
TIME CONSTANT:-
At the time of discharging, at time
T=RC, the ratio of Q/Q0 becomes Q/Q0=1 /e
This shows that RC is the time during which the charge on the condenser drops to 1/e of
the initial charge.
The Product RC is called the time constant of the circuit.
VOLTAGE ACROSS THE CAPACITOR:-
During Charging :- Voltage across a capacitor from definition is given as
V = Q/C
Therefore during charging from equation (i)

−t
Q Q0
= (1−e RC )
C C
( )
−t
Or V =V 0 1−e RC (iii)
During discharging:- In a similar manner as equation(iii) during discharging
−t
V =V 0 . e RC (iv)
Current through a condenser during charging is given by the relation

−t
I =I 0 e RC (v)
And during the process of discharging, it is given by the relation

−t
I =−I 0 e RC (vi)
It is clear from the equations (v) & (vi) that the current in the two cases is in the opposite
directions. I 0the maximum current during the charging and discharging process is given by
V0
R
Where V 0 is the potential difference across the capacitor when it is fully charged.
Time (µSec) Current (µA)

PROCEDURE
1. Connect the circuit as shown in the Fig. (1).

2. Select one pair of resistance and capacitor also adjusts voltage for 8VDC using
variable pot. Through charging and discharging kit toward charging position.
3. Switch ON the instrument Current Meter will show some reading in positive.
Note down the maximum current and time it takes to come down to almost near
to zero i.e. charging time.
4. Now through switch towards discharging DPM’s will show reading in the
negative value. Note down the current and time it takes to come almost near to
zero i.e. discharging time.
5. Repeat the steps 3-4 for 10V,12V& 15Vrespectively.
6. Repeat the steps 3-5 for different values of resistance and capacitors.
7. Note down the result in table No.1 and compare the graph from graph No.1
EXPERIMENT 2
Time (µSec) Voltage (V)
1. Connect the circuit as shown in the Fig.(2).

2. Select one pair of resistance & capacitor also adjusts voltage for 8VDC using
band switch through charging and discharging switch toward charging
position.
3. Switch ON the instrument, Voltmeter will show some reading in positive
increasing values. Note down the maximum voltage and time it takes to
come down to almost near to maximum i.e. charging time.
4. Now through switch towards discharging DPM’s will show readings in the
decreasing order. Note down the time it takes to come almost near to zero
i.e. discharging time.
5. Repeat the steps 3-4 for 10V,12V&15V respectively.
6. Repeat the steps 3-5 for different values of resistances and capacitors
7. Note down the result in Table No.2 and compare the graph from Graph No.2

Charging Discharging

Uploaded by

Copyright:

Available Formats

Charging Discharging

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Charging Discharging

Uploaded by

Copyright:

Available Formats

INSTRUCTION MANUAL

The instrument comprises of the following built in parts:-

1. Variable DC power supply of 0-15V available at sockets provided on front panel.

Capacity of a condenser is defined as the amount of charge required to establish a unit

Q=Q 0 ( 1−e−t / RC ) (i)

Where Q is the charge on plates at a time t

The discharging is given by the relation

Q=Q 0 e−t / RC (ii)

The above two equations are exponential in character.

At the time of discharging, at time

T=RC, the ratio of Q/Q0 becomes Q/Q0=1 /e

The Product RC is called the time constant of the circuit.

VOLTAGE ACROSS THE CAPACITOR:-

During Charging :- Voltage across a capacitor from definition is given as

Therefore during charging from equation (i)

Current through a condenser during charging is given by the relation

And during the process of discharging, it is given by the relation

Time (µSec) Current (µA)

1. Connect the circuit as shown in the Fig. (1).

Time (µSec) Voltage (V)

1. Connect the circuit as shown in the Fig.(2).

You might also like