Natural Gas Conversion Guide
Natural Gas Conversion Guide
Natural Gas Conversion Guide
Conversion Guide
1
M
C
c
m
m
2
Contents
SECTION 1
1.1) Standard Conversion Tables 8 - 13
SECTION 2
2.1) Terminology and Assumptions 16 - 18
2.2) Natural Gas (NG) 19 - 21
2.3) Liqueied Natural Gas (LNG) 22 - 23
2.4) Liqueied Petroleum Gas (LPG) 24 - 25
SECTION 3
3.1) Inter-Fuel Conversion Tables 28 - 33
SECTION 4
4.1) References/Links 36
SECTION 5
5.1) Terms 38 - 45
5.2) Abbreviations 46
5.3) Measurements 47
ACKNOWLEDGEMENT 48
Copyright © 2012 International Gas Union (IGU). The entire content of this publication is protected by
copyrights, full details of which are available from the publisher. All rights reserved. No part of this publication
may be reproduced, stored in retrieval systems or transmitted in any form or by any means – electronic,
mechanical, photocopying, recording or otherwise – without the prior permission of the copyright owner.
3
Message from the President of IGU
Dear colleagues, F
o
Thanks to technology, the energy industry today is moving towards o
an almost seamless environment. The consumer is now no longer m
locked to a single type of fuel. The ability to switch between using h
oil, natural gas and coal, has enabled one to take full advantage of
the most eficient and lowest priced source of energy. However, T
to do so, one has to calculate and compare which fuel, at the f
given point in time, would provide the “best value for money”. t
e
As a spokesperson for the IGU, I ind a conversion guide almost G
a necessity. You can never know what type of questions would be o
asked. Even within the gas industry, we use different measurement a
systems for different regions of the world. Hence, the best way is c
to equip oneself with a tool which would enable one to carry out a
a quick comparison of natural gas using a common denominator
or making inter-fuel comparisons. T
a
This Natural Gas Conversion Guide is IGU’s contribution to assist v
analysts from different types of background to quickly convert w
and ind the equivalent value between the three fossil fuels, under
a given set of parameters. This guide comprises four sections, T
namely: standard conversion tables; characteristics and conversion
tables for natural gas, liqueied natural gas (LNG), and liqueied
petroleum gas (LPG); inter-fuel conversion; and a set of glossary
of terms and abbreviations. The guide also comes in two sizes, P
a normal A5-sized handbook, and a pocket-sized booklet. 2
4
For those who do not have a copy of the guide, you can log
onto the IGU website (www.igu.org), and proceed to the section
s on natural gas conversion. For those who wish to undertake a
r more detailed conversion under a more complex environment, we
g have also included in the guide a list of “links” to a few websites.
f
, The publication of this conversion guide has been made possible
e from the contributions of a few organisations which had provided
their experts to participate in this initiative. I therefore wish to
express our heartfelt gratitude to PETRONAS, Shell, and Tokyo
t Gas, for their invaluable contributions. I also wish to thank those
e organisations whose previous publications have been used
t as reference by the team during the course of developing the
s conversion guide, in particular Shell, The Petroleum Economist,
t and Alphatania.
r
To conclude, I wish to emphasise that this guide is meant only
as a tool and a quick guide to assist you to ind the equivalent
t values for natural gas, LNG, LPG, oil and coal. I trust that you
t would ind the guide to be handy and useful.
r
, Thank you.
n
d
y Datuk (Dr) Abdul Rahim Hashim
, President, IGU
2009 - 2012 Malaysian IGU Presidency Triennium
5
6
Natural Gas
Conversion Guide
SECTION 1
7
Standard Conversion Tables
Conversion factors are rounded up to at most four
decimal places for approximaion purpose.
(1) Length
multiply by
Example: To convert 100 centimetres (cm) to inches (inch): 100 centimetres = 100 x 0.3937 = 39.37 inches
(2) Area
multiply by
square metre square inch square foot square yard acre hectare
(m2) (in2) (ft2) (yd2)
8
(3) Volume
multiply by
Imperial
US gallon
cubic cubic inch cubic foot cubic yard litre gallon Oil barrel
liquid
metre (m3) (in3) (ft3) (yd3) () liquid (US bbl)
(US gal.)
(Imp. gal.)
m3 61,024 35.31 1.308 1,000 220.0 264.2 6.290
in3 1.639 x 10-5 5.787 x 10-4 2.143 x 10-5 0.0164 0.0036 0.0043 1.031 x10-4
ft3 0.0283 1,728 0.0370 28.32 6.229 7.481 0.1781
3
yd 0.7646 46,656 27 764.6 168.2 202.0 4.809
0.001 61.02 0.0353 0.0013 0.22 0.2642 0.0063
Imp. gal. 0.0045 277.4 0.1605 0.0059 4.546 1.201 0.0286
US gal. 0.0038 231 0.1337 0.005 3.785 0.8327 0.0238
US bbl 0.159 9,702 5.615 0.2079 159 34.97 42
(4) Velocity
multiply by
9
(5) Mass
multiply by
ton
kilogram grain ounce pound metric long short
(kg) (gr) (oz) (lb) (tonne)
multiply by
ton-force
newton kilogram- pound-force poundal metric long short
(N) force (kgf) (lbf) (pdl) (tonne)
10
(7) Pressure
multiply by
multiply by
11
(9) Energy Or Work
multiply by
(10) Power
multiply by
12
(11) Rates Of Flow
multiply by
cubic metre/ cubic metre/hour cubic metre/day cubic foot/min cubic foot/hour cubic foot/day
minute (cm/min) (cm/h) x 103 (cm/d) x 103 (cf/min) (cf/h) x 103 (cf/d) x 103
(12) Temperature
o
C -50 -40 -30 -20 -10 0.0 +10 20 30 40 50 60 70 80 90 100
o
F -58 -40 -22 -4 14 32 50 68 86 104 122 140 158 176 194 212
From To Formula
Degrees Celsius Degrees Fahrenheit [(9/5) x oC] + 32
Degrees Fahrenheit Degrees Celsius (oF – 32) x 5/9
o
Degrees Celsius Kelvins C + 273.15
o
Kelvins Degrees Celsius C – 273.15
13
14
Natural Gas
Conversion Guide
SECTION 2
15
Terminology And Consituents
Of Natural Gas
METHANE
LNG
ETHANE
PROPANE
LPG
NATURAL BUTANE
GAS NGL
ex well PENTANES and heavier fractions also
referred to as:
C 5+
Pentanes plus
Natural gasoline
Condensate
NON-HYDROCARBONS
e.g. water, carbon dioxide, etc
16
Natural Gas Value Chain
Power
LPG Extraction Generation
LNG Gas
Industrial
Residential
Upstream
Methane
Gas District
Cooling
Ethane
NGV Transport
Export
Propane Petrochemical
Gas Processing Plant
Feedstock
Condensate Industrial
Refineries
17
Remarks & Key Assumpions N
This section is intended to provide additional information as a reference ONLY on the properties/characteristics
of natural gas, liqueied natural gas (LNG) and liqueied petroleum gas (LPG) for background understanding.
The approximations in the tables in Section 2 and Section 3 are based upon the following assumptions:-
(i) For natural gas:
l “Gas State” in conversion tables is assumed at Normal, N (0 oC, 1 atm)
1,100 Btu/scf (60 oF, 1 atm) = 1,163 Btu/cf (0 oC, 1 atm)
*Scf = Standard cubic feet. Standard means “(60 oF, 1 atm)”
(ii) For LNG
l 1 tonne LNG = 1,300 Nm3 gas [*N: Normal. Normal means “(0 oC, 1 atm)”];
l Density = 450 kg/m3 LNG
(iii) For LPG,
l An assumed 50/50 propane/butane mixture with (r) and (p) indicating that the LPG is either
refrigerated or pressurised.
l The simulation software known as “Virtual Materials Group (VMG) Process Simulator” is used
in the process. Other assumptions are as below:-
l Pressurised (p): temperature = 20 oC, Vapour Fraction (VapFrac) = 0
l Refrigerated (r): temperature = each boiling point, Pressure = 0 kPa (g), g = gauge pressure
Corresponding boiling points -> Ethane : -88.7 oC
Propane : -42.2 oC
n-Butane : -0.6 oC
C3.C4 mix : -29.2 oC
(iv) Caloriic values, mmBtu (gross):
18
Natural Gas (NG)
s
Introduction l Naturally occurring natural gas was discovered and identiied in America as early
as 1626, when French explorers discovered natives igniting gases that were
seeping into and around Lake Erie.
l Conventional natural gas is commonly found in underground sandstone
and limestone formation whereas Unconventional Gas refers to coal bed
methane, shale gas, gas hydrates and tight sand gas.
Deinition l A gaseous hydrocarbon fuel obtained from underground sources.
l Natural gas remains in the gaseous state under the temperature and pressure
conditions in service.
Compsoition l A mixture of primarily methane (CH4) and may also include ethane (C2H6), propane
(C3H8), butane (C4H10) and other higher hydrocarbons. It generally also includes
some inert gases, such as nitrogen (N) and carbon dioxide (CO2), plus minor
amounts of trace constituents.
19
Natural Gas Conversion Tables
multiply by
T
(2) Energy Consumption e
multiply by
(3) Gross Caloriic Value < > Net Caloriic Value (Natural Gas)
Gross Net
Gross 1 0.9 T
Net 1.1 1
20
(4) Gas Consumption for Industrial Purposes
Power Generation (Open Cycle) 1.0 bcm gas into plant 3,700 GWh electricity
Power Generation (Combined Cycle) 1.0 bcm gas into plant 5,800 GWh electricity
LNG Project (Plant and Shipping) 1.0 bcm gas into plant 0.85 bcm regasiied
Ammonia / Urea Production 1.0 bcm gas into plant 1.8 million tonnes fertiliser
Methanol Production 1.0 bcm gas into plant 1.1 million tonnes methanol
Gas-to-Liquids 1.0 bcm gas into plant 4.0 million barrels oil
These igures can vary greatly, depending on such factors as the process used, the design and age of the plant,
eficiency of operation, ambient conditions, etc. They should be used with caution and only for general exercises. All
numbers are rounded.
21
L
Introduction l Natural gas liquefaction dates back to the 19th century when British chemist
and physicist Michael Faraday experimented with liquefying different types of
gases, including natural gas.
l The irst LNG plant was built in West Virginia in 1912 and began operation in 1917.
In January 1959, the world’s irst LNG tanker, The Methane Pioneer, carried
an LNG cargo from Lake Charles, Louisiana to Canvey Island, United Kingdom.
Deinition l Natural gas, which after processing has been liqueied for storage and transportation
purpose. At atmospheric pressure, the LNG will be at temperature between
-161 °C and -158 °C.
Composition l Primarily methane (CH4) but also contains other components like ethane (C2H6),
butane (C4H10) up to hexane (C6H14) and nitrogen (N).
l Impurities may include carbon dioxide (CO2), sulphur (S), carbonyl sulphide (COS),
mercaptans and mercury (Hg).
Energy Density l Roughly in the range 410 kg/m3 (0.41 kg/ ) to 500 kg/m3 (0.5 kg/ ) depending
on temperature, pressure and composition.
l Speciic energy = 56.3 MJ/kg that is equivalent to 25,300 MJ/m3 (25.3 MJ/ ).
Pricing Formulas l Market price will vary according to where it is being sold, the local ‘marker’ prices
(e.g. HH, NBP), and the other contractual terms (e.g. crude oil-linked price, spot
cargo, long term, etc.)
22
LNG Conversion Tables
multiply by
Expansion
Nitrogen Methane Ethane Propane C4+ LNG Gas
ratio Gas GCV
Origin N2 C1 C2 C3 % density density
m3(n)/ MJ/m3 (n)
% % % % kg/m3 kg/m3 (n) m3 liq
Abu Dhabi 0.3 84.8 13.2 1.6 0.1 467 0.826 566 44.9
Algeria-Arzew 0.6 88.0 9.0 2.0 0.5 464 0.813 570 44.1
Algeria-Bethioua 1 0.9 88.1 8.4 2.0 0.7 455 0.806 573 35.7
Algeria-Bethioua 2 0.6 90.7 7.8 0.8 0.0 450 0.780 577 36.0
Algeria-Skikda 0.5 91.8 6.9 0.6 0.1 446 0.769 580 35.5
Australia-NWS 0.1 87.4 8.3 3.4 0.8 467 0.831 562 45.3
Brunei 0.1 90.6 5.0 2.9 1.5 461 0.816 564 44.6
Egypt-Damietta 0.1 97.7 1.8 0.22 0.2 427 0.730 585 40.8
Egypt-Idku 0.0 95.9 2.8 0.9 0.5 436 0.752 579 38.9
Equatorial Guinea 0.0 93.4 6.5 0.0 0.0 439 0.755 585 42.0
Indonesia-Arun 0.2 90.7 6.2 2.0 1.0 457 0.803 569 43.9
Indonesia-Badak 0.0 91.2 5.5 2.4 0.9 456 0.801 568 43.9
Indonesia-Tangguh 2.9 0.5 0.2 432 0.744 580 41.0
Libya 0.7 81.6 13.4 3.7 0.7 485 0.867 559 46.6
Malaysia 0.3 90.3 5.3 3.1 1.1 461 0.813 567 44.3
Nigeria 0.1 92.1 5.3 2.1 0.5 458 0.809 566 44.2
Norway 0.8 91.8 5.7 1.3 0.4 451 0.782 577 40.1
Oman 0.4 87.9 7.3 2.9 1.6 470 0.834 563 45.3
Peru 0.6 89.1 10.3 0.1 0.0 456 579
Qatar-Qatargas I 0.4 90.1 6.2 2.3 1.0 460 0.808 569 44.0
Russia-Sakhalin 0.1 92.6 4.5 1.9 0.2 449 570
Trinidad 0.0 97.1 2.5 0.2 0.1 429 0.727 590 39.8
U.S.A-Alaska 0.2 99.7 0.1 0.0 0.0 423 0.719 589 39.9
Yemen 0.0 93.3 5.7 0.9 0.1 434 0.765 567 38.5
23
Liqueied Petroleum Gas (LPG)
Deinition l A mixture of propane and butane which has been liqueied by reducing the
temperature, increasing the pressure or a combination of both. LPG is commonly
called “bottled gas.”
Composition l It is made up primarily by propane (C3H8) and butane (C4H10), or a mix of the two.
l Other hydrocarbons that include propylene, butylenes, isobutene and isobutylene
may also be present.
Characteristics l A higher percentage of propane is used in winter since propane is lighter than
butane and the same for butane in summer since it has a higher vapor pressure
and lower boiling point.
l Non-toxic, lammable gas, odorless, colorless and heavier than air.
l Volume typically is 250 times smaller in a liquid state based on composition,
pressure and temperature.
l Can be easily condensed, packaged, stored and utilised, which makes it an ideal
energy source for a wide range of applications.
Boiling Point l Varies considerably from about -42 oC to 0 oC (-44 oF to 32 oF) at atmospheric pressure.
24
(1) LPG & Ethane: Weight, Volume and Heat
C3. C4 mix is treated separately in which the results are generated from the VMG Simulator.
25
26
Natural Gas
Conversion Guide
SECTION 3
27
Inter-fuel Conversion Tables
The tables contain quick reference equivalents and other
factors of general relevance to the natural gas industry.
All igures are to be taken as APPROXIMATE VALUES only
for use when a high degree of precision is not required.
The approximaions in these tables are based upon the
assumpions that are listed in page 18.
28
r
.
y
.
e
29
(3) LNG: Volumetric Equivalents
30
(4) LPG (Refrigerated)
Equivalent based on 50% C3, 50% C4
31
(5) LPG (Pressurised)
Equivalent based on 50% C3, 50% C4
32
(6) Oil and Coal Equivalents
33
34
Natural Gas
Conversion Guide
SECTION 4
35
Selected References
The following references were used by the team in the preparation of this guide.
The IGU wishes to thank and record its appreciation to the respective publishers and organisations:-
[1] NATURAL GAS Physical and Engineering Data, Shell Companies in Malaysia, March 1983
[2] Natural Gas Equivalents, Shell International Gas Limited, 1992
[3] Natural Gas Fundamentals by Malcolm W.H. Peebles, Shell International Gas Limited, 1992
[4] The Alphatania Natural Gas Glossary of Terms & Measurements and Natural Gas
Conversion Tables, Alphatania Ltd.
[5] The Fundamentals of the Natural Gas Industry, The Petroleum Economist and Gas World
International, October 1995
[6] Fundamental of Natural Gas: An International Perspective, Vivek Chandra, September 2006
[7] Virtual Materials Group (VMG) Process Simulator, commercially available software
[8] LNG Industry in 2010, The International Group of Liquefied Natural Gas Importers (GIIGNL)
[9] Gas and LNG Industry Glossary, Alphatania Training,
http://www.gasstrategies.com/industry-glossary
[10] Santos, Conversion Calculator, http://www.santos.com/conversion-calculator.aspx
[11] Conversion Factors, BP, http://www.bp.com/conversionfactors.jsp
[12] Online Conversion, http://www.onlineconversion.com/
[13] OECD, Glossary of Statistical Terms, http://stats.oecd.org/glossary/detail.asp?ID=4109
[14] General Facts on LPG, LPGSOLUTIONS, http://www.lpg-solutions.co.uk/facts.html
[15] Standards, The American Society for Testing and Materials (ASTM) International,
http://www.astm.org/Standard/index.shtml
36
Natural Gas
Conversion Guide
-
3 SECTION 5
2
37
GLOSSARY OF TERMS
A
Acid Gas Natural gas that contains a certain quantity of gases such as carbon dioxide
(CO2) or hydrogen sulphide (H2S). These gases will form acidic compound when
combined with moisture.
Associated Gas Gas which coexists with oil in a primarily oil ield. It may be cap gas or solution gas,
where the differences are the behaviour and treatment.
Atmospheric Pressure The pressure of the weight of air and water vapour on the surface of the earth.
B
Boil-off gas Volume of gas naturally converted to gaseous phase when LNG in a storage tank
or ship warms to its boiling temperature. It may be collected and used for ship fuel
or reliqueied to LNG.
Boiling point Temperature at which a substance changes its state from liquid to gas.
Bottled Gas Usually butane or propane or both, stored in the liquid form at moderate pressure in
steel containers. Used in small residential and commercial applications.
British thermal Unit (Btu) A Btu is deined as the amount of heat required to raise the temperature of one 1
pound (0.454 kg) of liquid water by 1 °F (0.556 °C) at a constant pressure of an
atmosphere.
Bunker fuel Any fuel oil or diesel fuel taken into the bunkers of ships.
Butane A member of the alkane group of hydrocarbons that consists of four carbon atoms
in its molecule (C4H10, often abbreviated to C4 in non-technical usage). Colourless,
lammable gas at normal temperature and pressure but is easily liqueied by
pressure for storage and transportation are few of its characteristics. There are two
isomeric forms, Normal and Iso-Butane. At atmospheric pressure, Normal Butane
liqueies at -100 °C and Iso-Butane (Methylpropane) at 120 °C.
Normal Butane Iso-Butane (Methylpropane)
H H H H H H
l l l l H H H
H C C C C H
l
C C
l l l l H C H
H H H H
H C H
l
C
C 6+ All hydrocarbons with a carbon number of 6 and above also referred to as hexane
and heavier fractions.
Calorie (cal) A unit of heat that equals to 4.1868 joules. Formerly deined as the quantity of
heat required to raise the temperature of 1 gram of water by 1°C under standard
conditions. It has now largely been replaced by the joule for scientiic purposes.
Caloriic Value (CV) The amount of heat produced in a complete combustion of a fuel. This can be
measured either dry or saturated with water vapour; and net or gross.
Cap Gas Gas found in a gas cap in relation with oil but not commingled with it.
Capacity Charge Fee made for reserving capacity in a pipeline, a gas store or other piece of
infrastructure. Frequently used interchangeably with Demand Charge.
38
Churning A term used in gas trading to point out the number of times on average that gas is
traded between initial sale and ultimate consumption.
Coal Bed Methane Coal bed methane is methane that is or can be recovered from coal seams. Also
(CBM) well-known as Coal Seam Gas. Wells are drilled into suitable coal seams and the
pressure in the rock is reduced, usually by pumping out water in order to recover
CBM. The pumped out water may be saline and cause environmental issues until
the methane can be desorbed from the coal. CBM is not trapped beneath a seal like
conventional natural gas but is adsorbed into the coal.
Coal Gas Coal Gas is gas manufactured by the destructive distillation of bituminous coal.
The principal components are hydrogen (more than 50%), methane (10% to 30%)
carbon monoxide and higher hydrocarbons.
Coal Mine Methane Methane recovered from coal mines, whichever while active or after abandonment,
(CMM) which can be used in local power generation or heat production.
Combined Cycle Gas A CCGT is a type of electricity generation plant in which the heat generated from
Turbine (CCGT) combustion of the gases is used twice. Gas Turbine is driven by burning the gas.
Then, to raise steam for a secondary steam turbine unit, the hot exhaust gases
need to be passed through a heat exchanger. Combined cycle plants have a
thermal eficiency about 50% greater than a normal simple or open turbine.
Combined Heat and CHP is the use of a single uniied system to deliver both the heat and power
Power (CHP) requirements of a project, minimising the waste of heat. The power is formed
through gas turbines or another prime mover. The exhaust heat is harnessed for
requirements other than electricity generation. Also known as cogeneration and
total energy. It has a typical eficiency is of more than 70%.
Compressed Natural Gas Natural gas compressed into gas cylinders, mainly used as an alternative for liquid
(CNG) fuels in road vehicles. CNG remains a gas irrespective of the amount of pressure.
Condensate Natural gas liquid with low vapour pressure, produced from a reservoir with high
pressure and temperature. In a pipeline or separation plant, condensate will
separate naturally through the normal process of condensation. Can refer to any
mixture of relatively light hydrocarbons which stay put liquid at normal temperature
and pressure. There will be some propane and butane dissolved in it. Not like crude
oil, it contains little or none of the heavy hydrocarbons which make up heavy fuel
oil. There are three main sources of condensate:
39
D
Density (LNG or gas) The mass of a liquid or gas sample divided by its volume at speciied conditions of
pressure and temperature. The density is commonly expressed in kg/m3.
Dew Point When either hydrocarbons (hydrocarbon dew point) or water (water dew point) start
to condense out of a given gas stream, the temperatures below this phenomenon
is known as dew point. Condensation could reduce the accuracy of metering and
creates the trouble of liquid slugs in pipelines, which will need to be cleared out from
time to time by passing a Pig through the pipeline.
Downstream Those activities in the gas chain closest to inal customers.
Dry Gas Another name for Lean Gas. It does not mean free of water, though in some cases
it may be.
E
Energy Density The heating value per unit volume. It is measured as MJ per cubic metre. See Gross
Heating Value.
Ethane Ethane (C2H6, often abbreviated to C2 in non-technical usage) is one of the main
constituent elements of natural gas along with methane. Boils at -84.4 ºC. It is a
dry, colourless and odourless gas at normal temperatures. A feedstock for ethylene
production.
Ethylene Also known as Ethene. A colourless gas (C2H4) produced by cracking hydrocarbons
such as ethane or naphtha and used as a feedstock for petrochemicals, such as
ibres and many plastics. Boils at -103.7 ºC.
F
Feedstock Hydrocarbons used as raw material in an industrial process, not as a fuel. The
principal uses of natural gas as a feedstock are in the manufacture of ammonia,
ammonia-based fertilisers and methanol.
Flash point The lowest temperature corrected to barometric pressure of 101.3 kPa at which
application of ignition source causes the vapor of a specimen of the sample to ignite
under speciied condition of test (ASTM D93).
Floating LNG Floating LNG (FLNG) is the use of purpose built or converted ships to enable
regasiication of LNG (and liquefaction) to be carried out offshore. FLNG has the
advantage that LNG production and importation can start more quickly than could
happen onshore, where lead times are often lengthened by the local approval
process. It also enables the processes to move location to satisfy short term demand.
Fractionation A distillation process in which the distillate is collected as a number of separate
fractions based on a different boiling range.
Fuel Gas Gaseous fuels, in particular low pressure natural gas used to fuel production or
treatment facilities.
Fuel oil Fuel oil deines oils that make up distillation residue. It comprises all residue fuel oils,
including those obtained by blending. Its kinematic viscosity is above 10 cSt at 80 ºC.
The lash point is always above 50 ºC and the density is always higher than 0.90 kg/ .
G
Gas : Oil Ratio The relationship between the volume of gas produced at atmospheric pressure and
the volume of oil produced in a given ield. This volume will normally vary considerably
over the life of the ield. May be expressed as a simple volumetric ratio e.g. 500:1
or as ft3/barrel.
Gas-to-Liquid (GTL) Gas to Liquid (GTL) processes convert natural gas into Synthetic Gasoline or Middle
Distillates, by using the Fischer-Tropsch synthesis method. Increasingly relevant
where gas is found in ields remote from markets such that delivery by pipeline is
likely to be uneconomic.
Gas Condensate Ratio The ratio of gas to condensate in a gas or condensate reservoir, usually uttered in
practice as the ratio of condensate to gas. Usual units are barrels of condensate
per million cubic feet of gas.
40
Gas Liquefaction The conversion of natural gas into LNG.
Gas Processing The separation of oil, gas and the removal of impurities and natural gas liquids from
natural gas to meet the delivery speciication.
Gas Turbine A turbine propelled by the expansion of compressed air, heated by the combustion
of a fuel such as natural gas or gas oil. Commonly used for power generation.
Gravity A common abbreviation usually means speciic gravity in the UK and American
Petroleum Institute (API) gravity in the US.
Greenield A planned development which must be built from scratch on a new site without
existing infrastructure.
Gross Heating Value The amount of heat which would be released by the complete combustion in air of
(GHV or HHV) 1 kg, 1 Mol or 1 standard cubic metre (mass based, molar based or volume based)
of gas at conditions of t2,p2; in such a way that the pressure (p1) at which the
reaction takes place remains constant, and all the products of the combustion are
returned to the same speciied temperature (t1) as that of the reactants, all of these
components being in the gaseous state except for water formed by combustion,
which is condensed to the liquid state. The Gross Heating value mass based is
expressed in MJ/kg, Molar based in KJ/Mol and volume based in MJ/m3. This under
standard conditions of 15 ºC and 101,325 Pa. (ISO 6976:1995). See Energy Density.
H
Heel LNG LNG left in ship and shore storage tanks to maintain their cryogenic temperatures.
Henry Hub Henry Hub is owned and operated by Sabine Pipe Line, LLC, which is a wholly
owned subsidiary of ChevronTexaco and the largest centralised point for natural gas
spot and futures trading in the United States. Henry Hub is based on the physical
interconnection of nine interstate and four intrastate pipelines in Louisiana. The
New York Mercantile Exchange (NYMEX) uses Henry Hub as the notional point
of delivery for its natural gas futures contract. NYMEX deliveries at Henry Hub are
treated in the same way as cash-market transactions. Many natural gas marketers
also use Henry Hub as their physical contract delivery point or their price benchmark
for spot trades of natural gas.
High Sulphur Fuel Oil The term is the bottom of the oil barrel. The lowest priced oil product now, for
(HSFO) environmental reasons, frequently banned or only allowed to be used where rigorous
control of emissions is practiced. In some countries with developing gas-to-oil
competition, it represents the marker for power station fuel.
Hub Most frequently in the U.S. and now used in Europe. There are many hubs in the
U.S., of which the most important is Henry Hub (HH). In Europe the largest hub is
the National Balancing Point (NBP) in the U.K.
Hydrates Ice-like solids in which methane molecules are held within the molecular spaces of
the water molecule. Can form in pipelines and wells under certain conditions of near
freezing temperatures and high pressures.
Hydrocarbon An organic compound containing the elements hydrogen and carbon only.
Hydrocarbons exist as solids, liquids and gases.
I
Impurities Unwanted components that could be present in the product that might cause damage
to the manufacturing or processing facility. These can typically be solids, chemicals,
carbon dioxide (CO2), sulphur (S), mercaptans and mercury (Hg).
International Energy The IEA compiles detailed energy statistics and country reports, including countries
Agency (IEA) outside the organisation itself. An autonomous wing of the Organisation for Economic
Co-operation and Development (OECD). A Paris-based organisation which co-
ordinates the energy policies of its member countries.
International Gas Union A worldwide non-proit organisation that was founded in 1931 whose objective is to
(IGU) promote the political, technical and economic progress of the gas industry.
41
J
Japan Crude Cocktail Crude oil price based on average Japan importing price of a basket of crude oil
commonly used as an index for Asian LNG pricing.
Joules The derived SI unit of work or energy; the work done when the point of application
of a force of 1 newton is displaced through a distance of 1 metre in the direction
of the force.
K
Kerosene Kerosene (other than kerosene used for aircraft which is included with aviation fuels)
comprises reined petroleum distillate intermediate in volatility between gasoline and
gas/diesel oil. It is medium oil distilling between 150 °C and 300 °C.
L
Lean Gas Gas high in methane content typically 95% or more and with few higher fractions.
Thus of relatively low caloriic value. Also known as Dry Gas.
Line Pack It is a procedure for allowing more gas to enter a pipeline than is being withdrawn,
thus increasing the pressure, “iller” more gas into the system, and effectively
creating storage. The “illed” gas can subsequently be withdrawn when needed. A
useful method of meeting short term (hourly or diurnal) peak demand requirements.
Liquefaction The conversion of natural gas into LNG.
Liqueied natural gas Natural Gas, which after processing has been liqueied for storage and transportation
(LNG) purpose. At ambient pressure the LNG will be at temperatures close between
-161 °C to -158 °C.
Liqueied petroleum gas A mixture of propane and butane which has been liquefied by reducing the
(LPG) temperature, increasing the pressure or a combination of both. LPG is commonly
called “bottled gas.”
LNG Plant LNG plants consist of one or more LNG trains, each of which is an independent gas
liquefaction unit. It is more cost effective to add a train to an existing LNG plant,
than to build a new LNG plant, because infrastructure built for early trains, such as
ship terminals and other utilities, may be capable of being used or expanded for
new LNG trains. The process of Liquefaction is carried out in a liquefaction plant.
Load Factor Load factor is a measurement of utilisation for plant, or of the relationship between
average and peak demand or supply, as determined by the formula: Average x 100
/ Peak. For supply and demand calculations average and peak most often refer to
daily demand within a year, but any other periods are possible. The resulting igure
is usually expressed as a percentage.
Low sulphur fuel oil Fuel oil with low sulphur content. Usually less dense than high sulphur fuel oil. In
(LSFO) new markets with gas-to-oil competition, this frequently represents the marker fuel
for large segments of the industrial market.
M
Mercaptans Chemical compounds of sulphur used as Odorants.
Methane A colourless, odourless lammable gas, lighter than air under normal conditions (CH4,
often abbreviated to C1 in non-technical usage). Methane is the irst member in the
alkane (parafin) series and is the primary constituent of Natural Gas. At atmospheric
pressure, it liqueies at -162 ºC.
Methane number Rating indicating the knocking characteristics of a fuel gas (ISO 14532)
Methanol Methyl alcohol, produced from natural gas via Synthesis Gas. Used as a chemical
in the resin and paint industry and in the manufacture of Methyl Tertiary Butyl Ether
(MTBE) and acetic acid, but also of interest as a possible total or partial substitute
for motor gasoline in cars. Very toxic.
Middle Distillate Synthesis A chemical process using the Fischer-Tropsch synthesis method for making synthetic
(MDS) middle distillates (principally naphtha, kerosene and gas oil) from natural gas.
Midstream Those activities in the gas chain related to moving gas between the source and
local distribution.
42
N
Naphtha A mixture of several highly volatile lammable liquid hydrocarbon distilled from
petroleum, coal tar or natural gas and used as fuel, solvent, or as feedstock for various
chemicals. A feedstock destined either for the petrochemical industry (e.g. ethylene
manufacture or aromatics production) or for gasoline production by reforming or
isomerisation within the reinery.
National Balancing Point The NBP is an imaginary (notional or virtual) point at which all gas that has paid the
(NBP) entry charge to enter the UK National Transmission System is deemed to be located.
The point at which most UK gas trading takes place and the largest gas hub in Europe.
Natural Gas A gaseous fuel obtained from underground sources and consisting of a complex
mixture of hydrocarbons, primarily methane, but generally also including ethane,
propane and higher hydrocarbons in much smaller amounts. It generally also includes
some inert gases, such as nitrogen and carbon dioxide (CO2), plus minor amounts of
trace constituents. Natural gas remains in the gaseous state under the temperature
and pressure conditions normally found in service.
Natural Gas Liquids Heavier hydrocarbons found in natural gas production streams and extracted for
(NGLs) disposal separately. Within deined limits ethane, propane and butane may be left in
the gas to enrich the caloriic value. The terms natural gas liquids and condensates
are in practice used virtually interchangeably.
Natural Gasoline Butanes and heavier fractions extracted from rich natural gas which, after stabilisation
(removal of the lighter fractions) may be blended into motor gasoline.
Natural Gas Vehicle (NGV) A motorised vehicle powered by natural gas.
Net Caloriic Value (NCV) The heat generated by the complete combustion of a unit volume of gas in oxygen,
excluding the heat which would be recovered by condensing the water vapour
formed. It is usually seen as a measure of the effective heat produced rather than
the total heat in the gas.
Nitrogen Oxides Oxides of Nitrogen (NOx) resulting from the combustion of fuels, causing atmospheric
pollution in the form of smog.
Non-Associated Gas Non-Associated is gas found in a reservoir which contains no crude oil, and can
therefore be produced in patterns best suited to its own operational and market
requirements.
O
Odorants Strong smelling chemicals injected into natural gas, which otherwise is odourless,
in order to make its presence more easily detectable.
Odorisation The process of giving odourless natural gas a smell for safety reasons by injecting
small quantities of organic sulphur compounds, such as Mercaptans, typically at
the rate of 30 ppm. Usually carried out at the city gate or at the exit from the high
pressure transmission system.
Offtake Point The point in a gas system where gas is taken by supply pipe to a consumer.
Oil Gasiication The conversion of oil or naphtha into gas to be used as a fuel.
Open Cycle Gas Turbine A gas turbine, often derived from aero-engines, used for peak generation of electricity.
(OCGT) Also used in conjunction with a steam turbine in a combined cycle power plant. When
only the gas turbine is used it may be termed “single cycle”.
43
P
Peak Shaving Peak shaving is a means of reducing the peak load on the gas transportation and
supply system by supplying some gas from sources at or close to the point of ultimate
consumption, thus improving the average load factor. Peak shaving may be daily or
seasonal and will be handled in a variety of ways e.g. underground storage, peak shaving
LNG plants, line pack, gas holders, propane-air plant and, occasionally, special peak
shaving supply contracts.
Pentanes Plus Often used interchangeably with Condensates or C5+ but excluding Propanes and Butanes.
Petroleum The general name for hydrocarbons, including crude oil, natural gas and NGLs. The
name is derived from the Greek word petros (rock) and the Latin word oleum (oil).
Propane A member of the alkane (parafin) group of hydrocarbons with three carbon atoms in
its molecule (C3H8, often abbreviated to C3 in non-technical usage). Liqueies at -42 ºC.
Proven Reserves Those quantities of petroleum which, by analysis of geological and engineering data,
can be estimated with reasonable certainty to be commercially recoverable, from a
given date forward, from known reservoirs and under current economic conditions,
operating methods, and government regulations. Proven (proved) reserves can be
categorised as developed or undeveloped. Where probabilistic methods have been
used to estimate reserves, proven reserves are those with a better than 90% chance
of being economically recoverable. Sometimes abbreviated as P90.
Reserves with a greater than 50% chance but less than 90% chance are deined as
Probable, or P50. Reserves with a greater than 10% chance but less than 50% chance
are Possible or P10. Reserves may be classiied as proved, if facilities to process
and transport them to market are operational at the time of the estimate or there is a
reasonable expectation that such facilities will be installed.
R
R : P Ratio The reserves: production ratio is the number of years that current reserves would last
at current production levels. Thus, reserves of 100 divided by consumption of 20 / year
gives an R : P ratio of 5, and implies a life of 5 years for the reserves.
Raw Natural Gas Natural gas still containing impurities and unwanted substances, such as water (H2O),
nitrogen (N), carbon dioxide (CO2), hydrogen sulphide gas (H2S) and helium (He).
Regasiication The reconversion of LNG into gas suitable for pipeline transportation.
Reticulation A reticulation network is a small diameter, low pressure gas system serving residential
and commercial customers. (From the Latin word reta, meaning net).
Rich Gas Rich gas is gas with relatively large quantities of heavier fractions in its composition
(typically up to about 15%) and thus of high caloriic value. Also known as Wet Gas.
S
Sales Gas Raw gas, after processing to eliminate LPG, condensate and carbon dioxide. Usually,
sales gas consists chiely of methane and ethane and is odorised.
Sour Gas Gas containing a high level of carbon dioxide (CO2) or hydrogen sulphide (H2S), which
are acidic and corrosive in the presence of water. They may therefore need drying or
removal to conserve the pipeline.
Speciication The technical description of the allowable limits of the chemical composition of gas
which may be admitted into a pipeline or process.
Spot Trading A loose term covering the buying and selling of gas other than under a long term contract.
Generally, it means immediate delivery in trading parlance “spot delivery”.
Storage For natural gas, storage facilities fall into a number of categories. Seasonal storage
comprises depleted gas ields; aquifers; salt cavity storage; mined caverns; and
disused mines. Peak storage includes gas holders, line pack, lengths of pipeline buried
speciically for storage use, and LNG storage used either for base-load or peak-shaving
duties, depending on the market. Increasingly used in liberalised markets to enable gas *
to be traded at any time of the year for reasons not related to peak demand.
44
Sweet Gas Gas containing little or no carbon dioxide (CO2) or hydrogen sulphide (H2S)
Synthesis gas (Syngas) Synthetic gas mixture of hydrogen (H) and carbon monoxide (CO) produced from
methane and other hydrocarbons and steam used to produce various chemicals
notably methanol and GTL.
T
Take or Pay (TOP) A general provision in gas contracts under which, if the buyer’s annual purchased
volume is less than the Annual Contract Quantity minus any shortfall in the seller’s
deliveries, minus any Downward Quantity Tolerance, the buyer pays for such a shortfall
as if the gas had been received. The buyer may have the right in subsequent years to
take the gas paid for but not received, either free or for an amount to relect changes
in indexed prices.
Tariff A schedule of rates or charges offered by a common carrier or utility. Tariffs are
commonly available for all parts of the gas industry where third party access is enforced
or offered, for example for gas transmission in pipelines, for the use of gas stores, for
gas sales to residential customers.
Train An LNG production unit.
Transmission The transportation of huge quantities of gas at high pressures, often through national
or regional transmission systems. The gas is then transferred into local distribution
systems for supply to customers at lower pressures.
Transmission Pipeline A network of pipelines moving natural gas from a gas processing plant via compressor
stations, to storage centres or distribution points.
Treatment Any gas puriication process, but most generally applied to the treatment of gas
immediately after production, to bring it to adequate standard for the market in question
and/or to extract valuable components for separate sale. This may involve the removal
of LPGs and will certainly involve stripping out condensates, carbon dioxide (CO2) and
hydrogen sulphide (H2S) and other sulphur compounds mercury (Hg) and excessive
water (H2O) which may be in the raw gas.
U
Unconventional gas Collective term for natural gas, mainly methane, found such as coal bed methane,
shale gas, gas hydrates and tight sand gas whereas conventional gas is found within
sandstone and limestone reservoir.
Upstream Upstream typically refers to exploration, development and production of oil and gas.
V
Vapour pressure The pressure exerted by the vapour escaping from a liquid. As the temperature of the
liquid rises, its vapour pressure increases; eventually, it exceeds the pressure of the
conining atmosphere and the liquid boils.
W
Wet Gas Natural gas containing condensable hydrocarbons. A synonym for rich gas.
Wobbe Index Occasionally referred to as the Wobbe number. A measure of the rate at which gas will
deliver heat on combustion and hence of the compatibility of a gas with gas burning
equipment.
Y
Yellow Tipping Incomplete combustion whereby excess hydrocarbons can possibly result in
unacceptable levels of carbon monoxide (CO) being produced (ISO 14532).
* A more detailed list of glossary terms can be obtained from the IGU website, www.igu.org under the section on
natural gas conversion.
45
GLOSSARY OF ABBREVIATIONS
A
ACQ Annual Contract Quantity API American Petroleum Institute
ADP Annual Delivery Programme ASTM American Society for Testing and Materials
C
C&F Cost and Freight CIF Cost, Insurance and Freight
CBM Coal Bed Methane CMM Coal Mine Methane
CCGT Combined Cycle Gas Turbine CNG Compressed Natural Gas
CCS Carbon Capture and Storage COI Conirmation of Intent
CHP Combined Heat and Power CV Caloriic value
D
DDR Daily Delivery Rate DQT Downward Quantity Tolerance
F
FERC The Federal Energy Regulatory Commission FLNG Floating LNG
G
GCV Gross Caloriic Value GHV Gross Heating Value
GEMA Gas and Electricity Markets Authority GNL Gaz Natural Liquiié
(French language acronym for LNG)
H
HCV Higher Caloriic Value HOA Heads of Agreement
HHV Higher Heating Value HSFO High Sulphur Fuel Oil
I
IEA International Energy Agency IPE International Petroleum Exchange
IGU International Gas Union ISO International Organisation for
Standardisation
L
LCV Lower Caloriic Value LOI Letter of Intent
LDC Local Distribution Company LPG Liqueied Petroleum Gas
LHV Lower Heating Value
M
MDQ Maximum Daily Quantity MDR Maximum Daily Rate
MDS Middle Distillate Synthesis
N
NBP National Balancing Point NHV Net Heating Value
NCV Net Caloriic Value NTPA Negotiated Third Party Access
NGLs Natural Gas Liquids NYMEX New York Mercantile Exchange
NGV Natural Gas Vehicle
O
OCM On the day Commodity Market
S
Syngas Synthesis Gas
T
TPA Third Party Access TSO Transmission System Operator
TOP Take or Pay
U
UKCS United Kingdom Continental Shelf
46
GLOSSARY OF MEASUREMENTS
B
bar A term to specify natural gas pressure in pipelines. 1 bar is equal to 0.987 standard atmospheric pressure.
bbl A US barrel, 1 barrel = 0.159 cubic metres = 42 U.S. gallons (approx=35 imperial gallons).
bbl/day Barrels per day. Used to quantify a reiner’s output capacity or an oilield’s rate of low.
bcf Billion cubic feet (i.e. 109 cubic feet).
bcm Billion cubic metres (i.e. milliard or 109 cubic metres).
billion In the US, 109. The natural gas industry has generally adopted the US usage.
boe Barrels of oil equivalent. To quantify on general energy requirements. 1 boe equals to 5.8 MMBtu gross.
British thermal unit (Btu). A unit of heat generally used in the gas industry. The most common multiple is
one million Btu, normally abbreviated to mmBtu and USD/mmBtu is the unit for comparing gas prices on a
common basis.
C
cal Calorie is formerly the SI unit of energy. The most common multiple used is the Megacalorie (Mcal).
cf Cubic foot; cubic feet. The amount of gas required to ill a volume of one cubic foot. The term applied to the
volume of gas produced or consumed.
cm Cubic metre. cm is also the oficial abbreviation for centimetre.
G
GJ GigaJoule = (109) joule GWh Giga (109) Watts hour
K
kW KiloWatt = One thousand Watts (measurement of capacity)
kWh KiloWatt hour = One thousand Watts per hour (measurement of consumption)
M
Mcal Megacalorie (one million calorie) mmcm Million (106) cubic metres
mcf Thousand (103) cubic feet mmscf Million (106) standard cubic feet
mcm Thousand (103) cubic metres mmscm Million (106) standard cubic metres
mrd Milliard.Synonymous with US billion(109) MT Million (106) tonnes.
MJ MegaJoule (106) MTOE Million (106) tonnes of oil equivalent
mmbbl Million (106) barrels MTPA Million (106) tonnes per annum
mmBtu Million (106) British thermal units MW MegaWatt. One million (106) Watts
mmcf Million (106) cubic feet MWh MegaWatts hour
P
PJ Petajoules. A standard unit in the Australian gas industry, equals to 1 million (106) GJ and nearly 1 million mmBtu.
ppm Parts per million
psi Pounds per square inch. The common US/English unit of pressure, 14.5 psi = 1 bar.
S
scf standard cubic foot
scm standard cubic metre
SI Multiples These include103 kilo (k), 106 mega (M), 109 giga (G), 1012 tera (T), 1015 peta (P), 1018 exa (E).
T
tBtu Trillion (1012) Btu
tce Tonne of coal equivalent
TJ TeraJoules
tcf Trillion (1012) cubic feet
toe Tonne of oil equivalent
tcm Trillion (1012) cubic metres
Ton (t) To cover a variety of measures: the metric tonne (1,000 kg); the long tonne (2,240 lbs); the short tonne (2,000 lbs).
U
US $/bbl US Dollars per barrel
W
Watt (W) The basic unit of electrical power, deined as one joule per second
47
N
Acknowledgement
The IGU wishes to thank and record its appreciation
to the following members of the IGU Task Force and
the respective organisations:-
PETRONAS
(1) Lenny Marlina Omar
(2) Nurhaslina Abu Samah (Nasha)
(3) Raja Nor Azwina Raja Jaafar
Shell
(1) Marc Van Spaandonk
(2) Jaime Lai
Tokyo Gas
(1) Hideaki Shibata
(2) Naoki Nagamura
48
Notes
49
Notes
50
51
The International Gas Union (IGU), founded in
1931, is a worldwide non-profit organisation
promoting the political, technical and economic
progress of the gas industry with the mission to
advocate for gas as an integral part of a sustainable
global energy system. IGU has more than 110
members worldwide and represents more than 95%
of the world's gas market. The members are national
associations and corporations of the gas industry.
The working organisation of IGU covers the
complete value chain of the gas industry from
upstream to downstream. For more information
please visit www.igu.org.
52