Fortios v7.2.5 Release Notes

Release Notes
FortiOS 7.2.5
FORTINET DOCUMENT LIBRARY
https://docs.fortinet.com
FORTINET VIDEO GUIDE

https://video.fortinet.com
FORTINET BLOG
https://blog.fortinet.com
CUSTOMER SERVICE & SUPPORT

https://support.fortinet.com
FORTINET TRAINING & CERTIFICATION PROGRAM

https://www.fortinet.com/training-certification
FORTINET TRAINING INSTITUTE

https://training.fortinet.com
FORTIGUARD CENTER
https://www.fortiguard.com
END USER LICENSE AGREEMENT

https://www.fortinet.com/doc/legal/EULA.pdf
FEEDBACK
Email: [email protected]
June 12, 2023

FortiOS 7.2.5 Release Notes
01-725-857839-20230612
TABLE OF CONTENTS
Change Log 5
Introduction and supported models 6
Supported models 6
FortiGate 6000 and 7000 support 6
Special notices 7
IPsec phase 1 interface type cannot be changed after it is configured 7
IP pools and blackhole route configuration 7
FortiGate 6000 and 7000 incompatibilities and limitations 7
Hyperscale incompatibilities and limitations 8
Remove support for SHA-1 certificate used for web management interface (GUI) 8
Changes in GUI behavior 9
Changes in default behavior 10
Changes in table size 11
New features or enhancements 12
Upgrade information 18
Fortinet Security Fabric upgrade 18
Downgrading to previous firmware versions 19
Firmware image checksums 20
Strong cryptographic cipher requirements for FortiAP 20
FortiGate VM VDOM licenses 20
VDOM link and policy configuration is lost after upgrading if VDOM and VDOM link have
the same name 20
FortiGate 6000 and 7000 upgrade information 21
IPS-based and voipd-based VoIP profiles 22
Upgrade error message 23
Product integration and support 24
Virtualization environments 25
Language support 25
SSL VPN support 26
SSL VPN web mode 26
Resolved issues 27
Anti Spam 27
Anti Virus 27
Application Control 27
DNS Filter 28
Explicit Proxy 28
Firewall 28
FortiGate 6000 and 7000 platforms 29
FortiView 30
GUI 30
FortiOS 7.2.5 Release Notes 3

Fortinet Inc.
HA 32
Hyperscale 33
Intrusion Prevention 34
IPsec VPN 34
Log & Report 35
Proxy 36
REST API 38
Routing 38
Security Fabric 39
SSL VPN 40
Switch Controller 41
System 42
Upgrade 45
User & Authentication 45
VM 46
VoIP 47
Web Filter 47
WiFi Controller 47
ZTNA 48
Known issues 50
Anti Virus 50
Explicit Proxy 50
Firewall 50
FortiGate 6000 and 7000 platforms 51
GUI 52
HA 52
Hyperscale 52
IPsec VPN 53
Log & Report 53
Proxy 53
Routing 53
SSL VPN 54
Switch Controller 54
System 54
Web Filter 54
WiFi Controller 55
Built-in AV engine 56
Resolved engine issues 56
Built-in IPS engine 57
Resolved engine issues 57
Limitations 59
Citrix XenServer limitations 59
Open source XenServer limitations 59

Fortinet Inc.
Change Log
Date Change Description
2023-06-08 Initial release.
2023-06-12 Updated New features or enhancements on page 12, Resolved issues on page 27, Known
issues on page 50, Built-in AV engine on page 56, and Built-in IPS engine on page 57.
Added IP pools and blackhole route configuration on page 7 and Remove support for SHA-1
certificate used for web management interface (GUI) on page 8.

Fortinet Inc.
Introduction and supported models
This guide provides release information for FortiOS 7.2.5 build 1517.
For FortiOS documentation, see the Fortinet Document Library.
Supported models
FortiOS 7.2.5 supports the following models.
FortiGate FG-40F, FG-40F-3G4G, FG-60E, FG-60E-DSL, FG-60E-DSLJ, FG-60E-POE, FG-60F, FG-

61E, FG-61F, FG-70F, FG-71F, FG-80E, FG-80E-POE, FG-80F, FG-80F-BP, FG-80F-POE,
FG-81E, FG-81E-POE, FG-81F, FG-81F-POE, FG-90E, FG-91E, FG-100E, FG-100EF, FG-
100F, FG-101E, FG-101F, FG-140E, FG-140E-POE, FG-200E, FG-200F, FG-201E, FG-
201F, FG-300E, FG-301E, FG-400E, FG-400E-BP, FG-401E, FG-400F, FG-401F, FG-500E,
FG-501E, FG-600E, FG-601E, FG-600F, FG-601F, FG-800D, FG-900D, FG-1000D, FG-
1100E, FG-1101E, FG-1500D, FG-1500DT, FG-1800F, FG-1801F, FG-2000E, FG-2200E,
FG-2201E, FG-2500E, FG-2600F, FG-2601F, FG-3000D, FG-3000F, FG-3001F, FG-3100D,
FG-3200D, FG-3300E, FG-3301E, FG-3400E, FG-3401E, FG-3500F, FG-3501F, FG-3600E,
FG-3601E, FG-3700D, FG-3960E, FG-3980E, FG-4200F, FG-4201F, FG-4400F, FG-4401F,
FG-5001E, FG-5001E1, FG-6000F, FG-7000E, FG-7000F
FortiWiFi FWF-40F, FWF-40F-3G4G, FWF-60E, FWF-60E-DSL, FWF-60E-DSLJ, FWF-60F, FWF-

61E, FWF-61F, FWF-80F-2R, FWF-81F-2R, FWF-81F-2R-POE, FWF-81F-2R-3G4G-POE
FortiGate Rugged FGR-60F, FGR-60F-3G4G, FGR-70F, FGR-70F-3G4G
FortiFirewall FFW-3980E, FFW-VM64, FFW-VM64-KVM
FortiGate VM FG-ARM64-AWS, FG-ARM64-AZURE, FG-ARM64-GCP, FG-ARM64-KVM, FG-ARM64-

OCI, FG-VM64, FG-VM64-ALI, FG-VM64-AWS, FG-VM64-AZURE, FG-VM64-GCP, FG-
VM64-HV, FG-VM64-IBM, FG-VM64-KVM, FG-VM64-OPC, FG-VM64-RAXONDEMAND,
FG-VM64-SVM, FG-VM64-VMX, FG-VM64-XEN
Pay-as-you-go FOS-VM64, FOS-VM64-HV, FOS-VM64-KVM, FOS-VM64-XEN

images
FortiGate 6000 and 7000 support
FortiOS 7.2.5 supports the following FG-6000F, FG-7000E, and FG-7000F models:
FG-6000F FG-6300F, FG-6301F, FG-6500F, FG-6501F
FG-7000E FG-7030E, FG-7040E, FG-7060E
FG-7000F FG-7081F, FG-7121F

Fortinet Inc.
Special notices
l IPsec phase 1 interface type cannot be changed after it is configured on page 7

l IP pools and blackhole route configuration on page 7
l FortiGate 6000 and 7000 incompatibilities and limitations on page 7
l Hyperscale incompatibilities and limitations on page 8
l Remove support for SHA-1 certificate used for web management interface (GUI) on page 8
IPsec phase 1 interface type cannot be changed after it is

configured
In FortiOS 7.2.0 and later, the IPsec phase 1 interface type cannot be changed after it is configured. This is due to the
tunnel ID parameter (tun_id), which is used to match routes to IPsec tunnels to forward traffic. If the IPsec phase 1
interface type needs to be changed, a new interface must be configured.
IP pools and blackhole route configuration
Starting in FortiOS 6.4.9, 7.0.1, 7.2.0, and 7.4.0, all IP addresses used as IP pools and VIPs are no longer considered
local IP addresses if responding to ARP requests on these external IP addresses is enabled (set arp-reply enable
by default). In this case, the FortiGate is not considered a destination for those IP addresses and cannot receive reply
traffic at the application layer without special handling.
l This behavior affects FortiOS features in the application layer that use an IP pool as its source IP pool, including
SSL VPN web mode and explicit web proxy.
l When a blackhole route is configured in the routing table and matches the IP pool reply traffic, the FortiGate will not
receive reply traffic at the application layer and the corresponding the FortiOS feature will not work as desired.
l Configuring an IP pool as the source NAT IP address in a regular firewall policy works as before.
See IP pools and blackhole route configuration in the FortiOS Administration Guide for more information.
FortiGate 6000 and 7000 incompatibilities and limitations
See the following links for information about FortiGate 6000 and 7000 limitations and incompatibilities with FortiOS 7.2.5
features.
l FortiGate 6000 incompatibilities and limitations
l FortiGate 7000E incompatibilities and limitations
l FortiGate 7000F incompatibilities and limitations

Fortinet Inc.
Special notices
Hyperscale incompatibilities and limitations
See Hyperscale firewall incompatibilities and limitations in the Hyperscale Firewall Guide for a list of limitations and
incompatibilities with FortiOS 7.2.5 features.
Remove support for SHA-1 certificate used for web management

interface (GUI)
Starting in FortiOS 7.4.0, users should use the built-in Fortinet_GUI_Server certificate or SHA-256 and higher
certificates for the web management interface. For example:
config system global
set admin-server-cert Fortinet_GUI_Server
end

Fortinet Inc.
Changes in GUI behavior
Bug ID Description
742365 Prior to this enhancement, a ZTNA configuration required configuring:

l An EMS connection and EMS tags
l A ZTNA server configuration
l A ZTNA rules (proxy policy)
l An authentication scheme and rules (optional)
In this enhancement, there are now two ways to configure the ZTNA rule in the GUI.
1. Full ZTNA policy: under System > Feature Visibility, enable Explicit Proxy. Under Policy &
Objects > Proxy Policy, create a policy with the ZTNA type.
2. Simple ZTNA policy: a regular Firewall Policy is used for policy management. When creating a
new Firewall Policy, configure a ZTNA policy with ZTNA mode.
As a result, the Policy & Objects > ZTNA > ZTNA rules tab has been removed. Existing ZTNA rules
now appear in Policy & Objects > Proxy Policy after upgrade.

Fortinet Inc.
Changes in default behavior
Bug ID Description
837048 In the following scenarios, creating a matching address object for an interface is enabled
automatically and cannot be disabled:
l When creating a new interface with the LAN role.
l When an interface role is changed from a non-LAN role to a LAN role.
Once the address object is created, it cannot be deleted unless the interface role is changed to a
non-LAN role.
841712 On FortiGates licensed for hyperscale firewall features, the config system setting options
nat46-force-ipv4-packet-forwarding and nat64-force-ipv6-packet-forwarding
now also apply to NP7-offloaded traffic. The config system npu option nat46-force-ipv4-
packet-forwarding has been removed.

Fortinet Inc.
Changes in table size
Bug ID Description
870538 Increase firewall.address, firewall.service.group, and firewall.policy table size

for FG-600F and FG-601F. The new sizes are 4000, 4000, and 30000 respectively.
883103 Increase firewall.address from 40,000 to 50,000 for FG-1000D, FG-1100E, and FG-1101E.
Increase firewall.address from 65,000 to 100,000 for FG-1200D, FG-1500D, FG-1800F, FG-
1801F, FG-2000E, FG-2200E, FG-2201E, and FG-2500E.
Increase firewall.address from 65,000 to 150,000 for FG-2600F and FG-2601F.

Fortinet Inc.
New features or enhancements
More detailed information is available in the New Features Guide.
Feature ID Description
727383 Add GUI support for IPv6 addresses in Internet Service Database (ISDB), and allow them to be
configured in firewall policies.
745172 The information pane, which is located in the right-side gutter of many GUI pages, is enhanced to
display the top three contextually appropriate questions as hyperlinks under the Hot Questions at
FortiAnswers heading.
l Clicking a link takes the user to the related questions and answer page on the FortiAnswers
website.
l The number of answers, votes, and views is displayed for each question.
l Clicking the See more link takes the user to the related topic page on FortiAnswers.
The existing documentation related links have been renamed:

l The Documentation section header is renamed to Online Guides.
l The Online Help link is renamed to Relevant Documentation.
749989 FortiGates, FortiSwitches, FortiAPs, and FortiExtenders can download an EOS (end of support)
package automatically from FortiGuard during the bootup process or by using manual commands.
Based on the downloaded EOS package files, when a device passes the EOS date, a warning
message is displayed in the device's tooltip, and the device is highlighted in the GUI.
The End-of-Support security rating check rule audits the EOS of FortiGates and Fabric devices.
This allows administrators to have clear visibility of their Security Fabric, and help prevent any
security gaps or vulnerabilities that may arise due to any devices that are past their hardware EOS
date.
753177 Display IoT devices with known vulnerabilities on the Security Fabric > Asset Identity Center page's
Asset list view. Hovering over the vulnerabilities count displays a View IoT Vulnerabilities tooltip,
which opens the View IoT Vulnerabilities table that includes the Vulnerability ID, Type, Severity,
Reference, Description, and Patch Signature ID. Each entry in the Reference column includes the
CVE number and a link to the CVE details.
The Security Fabric > Security Rating > Security Posture report includes FortiGuard IoT Detection
Subscription and FortiGuard IoT Vulnerability checks. The FortiGuard IoT Detection Subscription
rating check will pass if the System > FortiGuard page shows that the IoT Detection Service is
licensed. The FortiGuard IoT Vulnerability rating check will fail if any IoT vulnerabilities are found.
To detect IoT vulnerabilities, the FortiGate must have a valid IoT Detection Service license, device
detection must be configured on a LAN interface used by IoT devices, and a firewall policy with an
application control sensor must be configured.
766158 Introduce a multi-tiered approach to determining the action taken on a video. The channel filter is
checked first, and if the video's channel matches a configuration entry, the corresponding action is
taken. If not, the FortiGuard category filter is checked and the corresponding action is taken if the
video's category matches a configuration entry. If neither of these conditions are met, the default
action specified in the video filter profile is used. Logging is also enabled by default.

Fortinet Inc.
config videofilter profile
edit <name>
set default-action {allow | monitor | block}
set log {enable | disable}
next
end
767570 Add the Fabric Overlay Orchestrator, which is an easy-to-use GUI wizard within FortiOS that
simplifies the process of configuring a self-orchestrated SD-WAN overlay within a single Security
Fabric without requiring additional tools or licensing. Currently, the Fabric Overlay Orchestrator
supports a single hub architecture and builds upon an existing Security Fabric configuration. This
feature configures the root FortiGate as the SD-WAN overlay hub and configures the downstream
FortiGates (first-level children) as the spokes. After configuring the Fabric Overlay, you can proceed
to complete the SD-WAN deployment configuration by configuring SD-WAN rules.
769722 Allow a managed FortiSwitch ID to be edited and store the device serial number as a new read-only
field.
config switch-controller managed-switch
edit <id>
set sn <serial_number>
next
end
The device ID can be configured to a maximum of 16 alphanumeric characters, including dashes (-)
and underscores (_).
Some related config, execute, and diagnose commands have been modified to configure and
display user-definable FortiSwitch IDs accordingly. The system data and daemons have been
modified to use the new switch serial number field to ensure the existing switch controller and
dependent features still work.
780571 Add Logs Sent Daily chart for remote logging sources (FortiAnalyzer, FortiGate Cloud, and
FortiAnalyzer Cloud) to the Logging & Analytics Fabric Connector card within the Security Fabric >
Fabric Connectors page and to the Dashboard as a widget for a selected remote logging source.
805867 Increase the number of supported NAC devices to 48 times the maximum number of FortiSwitch
units supported on that FortiGate model.
812329 Support DVLAN mode 802.1ad and 802.1Q on NP7 platforms, which provides better performance
and packet processing.
812993 Support the blocking of a discovered FortiExtender device on a FortiGate configured as a

FortiExtender controller using Reject Status in the GUI and set authorized disable in the
CLI.
config extension-controller extender
edit <name>
set id <string>
set authorized disable
next
end

Fortinet Inc.
819508 A FortiGate can allow single sign-on (SSO) from FortiCloud and FortiCloud IAM users with
administrator profiles inherited from FortiCloud or overridden locally by the FortiGate. Similarly,
users accessing the FortiGate remotely from FortiGate Cloud can have their permissions inherited
or overridden by the FortiGate.
819583 Add guards to Node.JS log generation and move logs to tmpfs to prevent conserve mode issues.
Node.JS logs only last a calendar day and will store up to 5 MB of logs. Once this limit is exceeded,
the log file is deleted and a new file is created. A delete option has been added to the Node.JS
debug command.
# diagnose nodejs logs {list | show <arg> | show-all | delete <arg>}
827464 The FortiGate device ID is carried by the IKEv2 message NOTIFY payload when it is configured.
config vpn ipsec phase1-interface
edit <name>
set dev-id-notification enable
set dev-id <string>
next
end
This device ID configuration is required when the FortiGate is configured as a secure edge LAN
extension for FortiSASE, and allows FortiSASE to distribute IKE/IPsec traffic according to the
FortiGate device ID to achieve load balancing.
829478 Improve replacement message displayed for YouTube videos blocked by video filtering. When a
user visits a video directly by URL, a full-page replacement message is displayed. When a user
loads a video from YouTube, the page will load but the replacement message will display in the
video frame.
836287 Support adding YAML to the file name when backing up the config as YAML, and detecting file
format when restoring the configuration.
The execute restore yaml-config command has been removed and execute restore
config should be used.
In the GUI, the File format field has been removed from the Restore system Configuration page.
836653 On FortiGates licensed for hyperscale firewall features, the following commands display summary
information for IPv4 or IPv6 hardware sessions.
# diagnose sys npu-session list-brief
# diagnose sys npu-session list-brief6
838363 Internet Service Database (ISDB) on-demand mode replaces the full-sized ISDB file with a much
smaller file that is downloaded onto the flash drive. This file contains only the essential entries for
Internet Services. When a service is used in a firewall policy, the FortiGate queries FortiGuard to
download the IP addresses and stores them on the flash drive. The FortiGate also queries the local
MAC Database (MADB) for corresponding MAC information.
set internet-service-database on-demand
end

Fortinet Inc.
839877 FortiPolicy can be added to the Security Fabric. When FortiPolicy joins the Security Fabric and is
authorized in the Security Fabric widget, it appears in the Fabric topology pages. A FortiGate can
grant permission to FortiPolicy to perform firewall address and policy changes. Two security rating
tests for FortiPolicy have been added to the Security Posture scorecard.
849515 Add auto-discovery-crossover option under config vpn ipsec phase1-interface to

block or allow (default) the set-up of shortcut tunnels between different network IDs.
config vpn ipsec phase1-interface
edit <name>
set auto-discovery-crossover {allow | block}
next
end
When auto-discovery-crossover is set to block on the auto-discovery sender:

l In a single hub case, the hub knows the network ID of all the shortcut endpoints.
l The shortcut offer trigger will be suppressed if IKE detects that the ingress tunnel and egress
tunnel have different network IDs.

When auto-discovery-crossover is set to block on the auto-discovery receiver:
l In a multi-hub case, the hub may not know the network ID of the endpoint where traffic is
forwarded.
l Peers will exchange information on whether the shortcut cross-over is allowed.
l The shortcut initiator will send its network ID and cross-over setting to the shortcut responder in
the shortcut query message.

l The shortcut responder will then send back its own network ID and any error status.
l If cross-over is not allowed on any side:
l The shortcut responder will not allocate a phase 1 and sets the error status in the shortcut
reply.
lThe shortcut initiator will not initiate the shortcut connection if it receives an error in the
shortcut reply.
When auto-discovery-crossover is set to allow:
l The cross-over shortcut connection will be initialized with network ID of 0.
l The non-cross-over shortcut connection will use the configured network ID number.
849771 Support Shielded and Confidential VM modes on GCP where the UEFI VM image is used for secure
boot, and data in use is encrypted during processing.
854704 FortiGate VMs with eight or more vCPUs can be configured to have a minimum of eight cores to be
eligible to run the full extended database (DB). Any FortiGate VM with less than eight cores will
receive a slim version of the extended DB. This slim-extended DB is a smaller version of the full
extended DB, and it is designed for customers who prefer performance.
855520 Harden REST API and GUI access.
855561 Use API endpoint domain name from instance metadata to support FortiOS VM OCI DRCC region.
855684 Allow users to configure the RADIUS NAS-ID as a custom ID or the hostname. When deploying a
wireless network with WPA-Enterprise and RADIUS authentication, or using the RADIUS MAC
authentication feature, the FortiGate can use the custom NAS-ID in its Access-Request.

Fortinet Inc.
config user radius
edit <name>
set nas-id-type {legacy | custom | hostname}
set nas-id <string>
next
end
858786 When configuring a CGN IP pool for a hyperscale firewall, exclude IP addresses within this IP pool
from being used for source NAT (excludeip). This allows users to remain secure and mitigate
attacks by ensuring that global IP addresses within a CGN IP pool that are being targeted by
external attackers are not re-used by other users of the hyperscale firewall.
config firewall ippool
edit <name>
set type cgn-resource-allocation
set startip <IPv4_address>
set endip <IPv4_address>
set excludeip <IPv4_address>, <IPv4_address>, <IPv4_address> ...
next
end
This option is currently not supported with a fixed allocation CGN IP pool (when set cgn-
fixedalloc enable is configured).
860965 Support the AWS T4g instance family with the FG-ARM64-AWS firmware image. Support the AWS
C6a and C6in instance families with the FG-VM64-AWS firmware image.
866174 The wtp-profile of FAP-432F, FAP-433F, FAP-U432F, and FAP-U433F models can set
external antenna parameters when the corresponding external antenna is installed.
config wireless-controller wtp-profile
edit <name>
config radio-1
set optional-antenna {none | FANT-04ABGN-0606-O-R | FANT-04ABGN-
0606-P-R}
end
next
end
868164 Implement BIOS-level signature and file integrity checking for important system files and
executables. Warn users of failed integrity checks, or prevent the system from booting depending
on the severity and BIOS verification level.
Kernel and userspace processes can also periodically verify the integrity of AV and IPS engine files,
and other important system files and executables.
FortiOS firmware and each release of an AV or IPS engine file are dually-signed by Fortinet CA and
third-party CAs.
868592 Support Saudi Cloud Computing Company (SCCC) and alibabacloud.sa domain (a standalone
cloud backed by AliCloud).

Fortinet Inc.
869198 Make the health check sensitive enough to detect small amounts of packet loss by decreasing the
link monitor check interval and probe timeout minimum limit down to 20 ms, which will significantly
impact VOD/voice.
881186 Support deploying VMware FortiGate VMs directly as a Zero Trust Application Gateway using the
OVF template (.vapp). ZTNA related parameters such as EMS server, external and internal
interface IPs, and application server mapping can be configured during OVF deployment. ZTNA
policies, authentication schemes, rules, and user groups are also bootstrapped.
894191 Improve GUI memory consumption for FortiGates with 2 GB of RAM or less.
901576 Simplify BLE iBeacon provisioning whereby the BLE major ID can be set in WTP and WTP group
settings (in addition to being set in the BLE profile settings), and the BLE minor ID can be set in the
WTP settings (in addition to being set in the BLE profile settings).
config wireless-controller wtp
edit <id>
set ble-major-id <integer>
set ble-minor-id <integer>
next
end
config wireless-controller wtp-group

edit <name>
set ble-major-id <integer>
set wtps <wtp-id1>, <wtp-id2>, ...
next
end
The BLE major ID defined in the WTP settings overrides the BLE major ID defined in the WTP group
settings and the BLE major ID defined in the BLE profile settings.
The BLE major ID defined in the WTP group settings overrides the BLE major ID defined in the BLE
profile settings.
The BLE minor ID defined in the WTP settings overrides the BLE minor ID defined in the BLE profile
settings.

Fortinet Inc.
Upgrade information
Supported upgrade path information is available on the Fortinet Customer Service & Support site.
To view supported upgrade path information:
1. Go to https://support.fortinet.com.
2. From the Download menu, select Firmware Images.
3. Check that Select Product is FortiGate.
4. Click the Upgrade Path tab and select the following:
l Current Product
l Current FortiOS Version
l Upgrade To FortiOS Version
5. Click Go.
Fortinet Security Fabric upgrade
FortiOS 7.2.5 greatly increases the interoperability between other Fortinet products. This includes:
FortiAnalyzer l 7.2.3
FortiManager l 7.2.3
FortiExtender l 4.0.0 and later. For compatibility with latest features, use latest 7.0 version.
FortiSwitch OS l 6.4.6 build 0470 or later

(FortiLink support)
FortiAP l See Strong cryptographic cipher requirements for FortiAP on page 20

FortiAP-S
FortiAP-U
FortiAP-W2
FortiClient* EMS l 7.0.3 build 0229 or later
FortiClient* Microsoft l 7.0.3 build 0193 or later

Windows
FortiClient* Mac OS X l 7.0.3 build 0131 or later
FortiClient* Linux l 7.0.3 build 0137 or later
FortiClient* iOS l 7.0.2 build 0036 or later
FortiClient* Android l 7.0.2 build 0031 or later
FortiSandbox l 2.3.3 and later for post-transfer scanning

l 4.2.0 and later for post-transfer and inline scanning

Fortinet Inc.
Upgrade information
*
If you are using FortiClient only for IPsec VPN or SSL VPN, FortiClient version 6.0 and later are supported.
When upgrading your Security Fabric, devices that manage other devices should be upgraded first.
When using FortiClient with FortiAnalyzer, you should upgrade both to their latest versions.
The versions between the two products should match. For example, if using FortiAnalyzer
7.2.0, use FortiClient 7.2.0.
Upgrade the firmware of each device in the following order. This maintains network connectivity without the need to use
manual steps.
1. FortiAnalyzer
2. FortiManager
3. Managed FortiExtender devices
4. FortiGate devices
5. Managed FortiSwitch devices
6. Managed FortiAP devices
7. FortiClient EMS
8. FortiClient
9. FortiSandbox
10. FortiMail
11. FortiWeb
12. FortiNAC
13. FortiVoice
14. FortiDeceptor
15. FortiNDR
16. FortiTester
17. FortiMonitor
18. FortiPolicy
If Security Fabric is enabled, then all FortiGate devices must be upgraded to 7.2.5. When
Security Fabric is enabled in FortiOS 7.2.5, all FortiGate devices must be running FortiOS
7.2.5.
Downgrading to previous firmware versions
Downgrading to previous firmware versions results in configuration loss on all models. Only the following settings are
retained:
l operation mode
l interface IP/management IP
l static route table
l DNS settings
l admin user account

Fortinet Inc.
Upgrade information
l session helpers
l system access profiles
Firmware image checksums
The MD5 checksums for all Fortinet software and firmware releases are available at the Customer Service & Support
portal, https://support.fortinet.com. After logging in, go to Support > Firmware Image Checksums (in the Downloads
section), enter the image file name including the extension, and click Get Checksum Code.
Strong cryptographic cipher requirements for FortiAP
FortiOS 7.0.0 has removed 3DES and SHA1 from the list of strong cryptographic ciphers. To satisfy the cipher
requirement, current FortiAP models whose names end with letter E or F should be upgraded to the following firmware
versions:
l FortiAP (F models): version 6.4.3 and later
l FortiAP-S and FortiAP-W2 (E models): version 6.2.4, 6.4.1, and later
l FortiAP-U (EV and F models): version 6.0.3 and later
l FortiAP-C (FAP-C24JE): version 5.4.3 and later
If FortiGates running FortiOS 7.0.1 and later need to manage FortiAP models that cannot be upgraded or legacy FortiAP
models whose names end with the letters B, C, CR, or D, administrators can allow those FortiAPs' connections with
weak cipher encryption by using compatibility mode:
config wireless-controller global
set tunnel-mode compatible
end
FortiGate VM VDOM licenses
FortiGate VMs with one VDOM license (S-series, V-series, FortiFlex) have a maximum number or two VDOMs. An
administrative type root VDOM and another traffic type VDOM are allowed in 7.2.0 and later. After upgrading to 7.2.0 and
later, if the VM previously had split-task VDOMs enabled, two VDOMs are kept (the root VDOM is an administrative
type).
VDOM link and policy configuration is lost after upgrading if VDOM

and VDOM link have the same name
Affected versions:
l FortiOS 6.4.9 and later

Fortinet Inc.
Upgrade information

When upgrading to one of the affected versions, there is a check within the set vdom-links function that rejects vdom-
links that have the same name as a VDOM. Without the check, the FortiGate will have a kernel panic upon bootup
during the upgrade step.
A workaround is to rename the vdom-links prior to upgrading, so that they are different from the VDOMs.
FortiGate 6000 and 7000 upgrade information
Upgrade FortiGate 6000 firmware from the management board GUI or CLI. Upgrade FortiGate 7000 firmware from the
primary FIM GUI or CLI. The FortiGate 6000 management board and FPCs or the FortiGate 7000 FIMs and FPMs all run
the same firmware image. Upgrading the firmware copies the firmware image to all components, which then install the
new firmware and restart. A FortiGate 6000 or 7000 firmware upgrade can take a few minutes, the amount of time
depending on the hardware and software configuration and whether DP or NP7 processor software is also upgraded.
On a standalone FortiGate 6000 or 7000, or an HA cluster with uninterruptible-upgrade disabled, the firmware
upgrade interrupts traffic because all components upgrade in one step. These firmware upgrades should be done during
a quiet time because traffic can be interrupted for a few minutes during the upgrade process.
Fortinet recommends running a graceful firmware upgrade of a FortiGate 6000 or 7000 FGCP HA cluster by enabling
uninterruptible-upgrade and session-pickup. A graceful firmware upgrade only causes minimal traffic
interruption.
Fortinet recommends that you review the services provided by your FortiGate 6000 or 7000
before a firmware upgrade and then again after the upgrade to make sure that these services
continue to operate normally. For example, you might want to verify that you can successfully
access an important server used by your organization before the upgrade and make sure that
you can still reach the server after the upgrade and performance is comparable. You can also
take a snapshot of key performance indicators (for example, number of sessions, CPU usage,
and memory usage) before the upgrade and verify that you see comparable performance after
the upgrade.
To perform a graceful upgrade of your FortiGate 6000 or 7000 to FortiOS 7.2.5:
1. Use the following command to enable uninterruptible-upgrade to support HA graceful upgrade:

config system ha
set uninterruptible-upgrade enable
end
2. Download the FortiOS 7.2.5 FG-6000F, FG-7000E, or FG-7000F firmware from https://support.fortinet.com.
3. Perform a normal upgrade of your HA cluster using the downloaded firmware image file.
4. When the upgrade is complete, verify that you have installed the correct firmware version.
For example, check the FortiGate dashboard or use the get system status command.
5. Confirm that all components are synchronized and operating normally.
For example, go to Monitor > Configuration Sync Monitor to view the status of all components, or use diagnose
sys confsync status to confirm that all components are synchronized.

Fortinet Inc.
Upgrade information
IPS-based and voipd-based VoIP profiles
Starting in FortiOS 7.2.5, the new IPS-based VoIP profile allows flow-based SIP to complement SIP ALG while working
together. There are now two types of VoIP profiles that can be configured:
config voip profile
edit <name>
set feature-set {ips | voipd}
next
end
A voipd-based VoIP profile is handled by the voipd daemon using SIP ALG inspection. This is renamed from proxy in
previous FortiOS versions.
An ips-based VoIP profile is handled by the IPS daemon using flow-based SIP inspection. This is renamed from flow in
previous FortiOS versions.
Both VoIP profile types can be configured at the same time on a firewall policy. For example:
config firewall policy
edit 1
set voip-profile "voip_sip_alg"
set ips-voip-filter "voip_sip_ips"
next
end
Where:
l voip-profile can select a voip-profile with feature-set voipd.
l ips-voip-filter can select a voip-profile with feature-set ips.
The VoIP profile selection within a firewall policy is restored to pre-7.0 behavior. The VoIP profile can be selected
regardless of the inspection mode used in the firewall policy. The new ips-voip-filter setting allows users to select
an IPS-based VoIP profile to apply flow-based SIP inspection, which can work concurrently with SIP ALG.
Upon upgrade, the feature-set setting of the voip profile determines whether the profile applied in the firewall
policy is voip-profile or ips-voip-filter.
Before upgrade After upgrade

config voip profile config voip profile
edit "ips_voip_filter" edit "ips_voip_filter"
set feature-set flow set feature-set ips
next next
edit "sip_alg_profile" edit "sip_alg_profile"
set feature-set proxy set feature-set voipd
next next
end end

edit 1
edit 1
set ips-voip-filter "ips_voip_
set voip-profile "ips_voip_filter"
filter"
next
next
edit 2
edit 2

Fortinet Inc.
Upgrade information
Before upgrade After upgrade

set voip-profile "sip_alg_profile" set voip-profile "sip_alg_profile"
next next
end end
Upgrade error message
The FortiGate console will print a Fail to append CC_trailer.ncfg_remove_signature:error in stat

error message after upgrading from 7.2.4 to 7.2.5 or later. Affected platforms include: FFW-3980E, FFW-VM64, and
FFW-VM64-KVM. A workaround is to run another upgrade to 7.2.5 or later.

Fortinet Inc.
Product integration and support
The following table lists FortiOS 7.2.5 product integration and support information:
Web browsers l Microsoft Edge 114

l Mozilla Firefox version 113
l Google Chrome version 114
Other browser versions have not been tested, but may fully function.
Other web browsers may function correctly, but are not supported by Fortinet.
Explicit web proxy browser l Microsoft Edge 114

l Mozilla Firefox version 113
l Google Chrome version 114
Other browser versions have not been tested, but may fully function.
Other web browsers may function correctly, but are not supported by Fortinet.
FortiController l 5.2.5 and later

Supported models: FCTL-5103B, FCTL-5903C, FCTL-5913C
Fortinet Single Sign-On l 5.0 build 03011 and later (needed for FSSO agent support OU in group
(FSSO) filters)
l Windows Server 2022 Standard
l Windows Server 2022 Datacenter
l Windows Server 2019 Core
l Windows Server 2012 R2 Standard
l Windows Server 2008 64-bit (requires Microsoft SHA2 support
package)
l Windows Server 2008 R2 64-bit (requires Microsoft SHA2 support
package)
l Windows Server 2008 Core (requires Microsoft SHA2 support package)
l Novell eDirectory 8.8
AV Engine l 6.00288
IPS Engine l 7.002314

Fortinet Inc.
Virtualization environments
The following table lists hypervisors and recommended versions.
Hypervisor Recommended versions
Citrix Hypervisor l 8.1 Express Edition, Dec 17, 2019
Linux KVM l Ubuntu 18.0.4 LTS

l Red Hat Enterprise Linux release 8.4
l SUSE Linux Enterprise Server 12 SP3 release 12.3
Microsoft Windows Server l 2012R2 with Hyper-V role
Windows Hyper-V Server l 2019
Open source XenServer l Version 3.4.3

l Version 4.1 and later
VMware ESXi l Versions 6.5, 6.7, and 7.0.
Language support
The following table lists language support information.
Language support
Language GUI
English ✔
Chinese (Simplified) ✔
Chinese (Traditional) ✔
French ✔
Japanese ✔
Korean ✔
Portuguese (Brazil) ✔
Spanish ✔

Fortinet Inc.
SSL VPN support
SSL VPN web mode
The following table lists the operating systems and web browsers supported by SSL VPN web mode.
Supported operating systems and web browsers
Operating System Web Browser
Microsoft Windows 7 SP1 (32-bit & 64-bit) Mozilla Firefox version 113
Google Chrome version 113
Microsoft Windows 10 (64-bit) Microsoft Edge

Mozilla Firefox version 113
Ubuntu 20.04 (64-bit) Mozilla Firefox version 113

macOS Ventura 13 Apple Safari version 15

Mozilla Firefox version 113
iOS Apple Safari

Mozilla Firefox
Google Chrome
Android Mozilla Firefox

Google Chrome
Other operating systems and web browsers may function correctly, but are not supported by Fortinet.

Fortinet Inc.
Resolved issues
The following issues have been fixed in version 7.2.5. To inquire about a particular bug, please contact Customer
Service & Support.
Anti Spam
Bug ID Description
857911 The Anti-Spam Block/Allow List Entry dialog page is not showing the proper Type values in the
dropdown.
877613 Mark as Reject can be still chosen as an Action in an Anti-Spam Block/Allow List in the GUI.
Anti Virus
Bug ID Description
818092 CDR archived files are deleted at random times and not retained.
849020 FortiGate enters conserve mode and the console prints a fork() failed message.
851706 Nothing is displayed in the Advanced Threat Protection Statistics dashboard widget.
863461 Scanunit displays unclear warnings when AV package validation fails.
869398 FortiGate sends too many unnecessary requests to FortiSandbox and causes high resource usage.
895950 Critical log message, Fortigate mmdb signature is missing, is generated on a unit
without an AVDB contract.
Application Control
Bug ID Description
857632 Unable to access to some websites when application control with deep inspection is enabled.

Fortinet Inc.
Resolved issues
DNS Filter
Bug ID Description
871854 DNS UTM log still presents unknown FortiGuard category even when the DNS proxy received a
rating value.
878674 Forward traffic log is generated for allowed DNS traffic if the DNS filter is enabled but the policy is
set to log security events only.
Explicit Proxy
Bug ID Description
842016 Client gets 304 response if a cached object has varying headers and is expired.
849794 Random websites are not accessible with proxy policy after upgrading to 6.4.10.
865135 Multipart boundary parsing failed with CRLF before the end of boundary 1.
875736 The proxy-re-authentication-mode option has been removed in 7.2.4 and is replaced with
proxy-keep-alive-mode re-authentication. The new proxy-re-authentication-
time timer is associated with this re-authentication mode. There are two unresolved issues:
l After upgrading, the previously configured proxy-auth-timeout value for the absolute re-
authentication mode is not preserved in the new proxy-re-authentication-time.

l The new proxy-re-authentication-time is currently configured in seconds, but it
should be configured in minutes to be consistent with other related authentication timers (such
as proxy-auth-timeout).
880361 Transparent web proxy policy has no match if the source or destination interface is the same and
member of SD-WAN.
901239 Multiple WAD crashes after upgrading firmware to 7.2.4.
901614 Firewall schedule does not work as expected with a proxy policy.
Firewall
Bug ID Description
719311 On the Policy & Objects > Firewall Policy page in 6.4.0 onwards, the IPv4 and IPv6 policy tables are
combined but the custom section name (global label) is not automatically checked for duplicates. If
there is a duplicate custom section name, the policy list may show empty for that section. This is a
display issue only and does not impact policy traffic.

Fortinet Inc.
Resolved issues
Bug ID Description
770541 Within the Policy & Objects menu, the firewall, DoS, and traffic shaping policy pages take around
five seconds to load when the FortiGate cannot reach the FortiGuard DNS servers.
804603 An httpsd singal 6 crash occurs due to /api/v2/monitor/license/forticare-resllers.
816493 The set sub-type ems-tag option is blocked in HA diff installation.
835413 Inaccurate sFlow interface data reported to PRTG after upgrading to 7.0.
840689 Virtual server aborts connection when ssl-max-version is set to tls-1.3.
851212 After traffic flow changes to FGSP peer from owner, iprope information for synchronized sessions
does not update on the peer side.
854901 Full cone NAT (permit-any-host enable) causes TCP session clash.
856187 Explicit FTPS stops working with IP pool after upgrading.
860480 FG-3000D cluster kernel panic occurs when upgrading from 7.0.5 to 7.0.6 and later.
861990 Increased CPU usage in softirq after upgrading from 7.0.5 to 7.0.6.
864612 When the service protocol is an IP with no specific port, it is skipped to be cached and causes a
protocol/port service name in the log.
865661 Standard and full ISDB sizes are not configurable on FG-101F.
872744 Packets are not matching the existing session in transparent mode.
875565 The policy or other cache lists are sometimes not freed in time. This may cause unexpected policies
to be stored in the cache list.
884578 Virtual server stops working after upgrading to 7.2.4.
895962 Virtual server with the HTTP HOST method is crashing WAD.
897849 Firewall Policy list may show empty sequence grouping sections if multiple policies are sharing the
same global-label.
912740 On a FortiGate managed by FortiManager, after upgrading to 7.4.0, the Firewall Policy list may
show separate sequence grouping for each policy because the global-label is updated to be
unique for each policy.
FortiGate 6000 and 7000 platforms
Bug ID Description
838036 Merge FortiGate 6000 and 7000 series platforms.
888873 The FortiGate 7000E and 7000F platforms do not support GTP and PFCP load balancing.
902545 Unable to select a management interface LAG to be the direct SLBC logging interface.

Fortinet Inc.
Resolved issues
Bug ID Description
905692 On a FortiGate 6000 or 7000, the active worker count returned by the output of diagnose sys ha
dump-by group can be incorrect after an FPC or FPM goes down.
905788 Unable to select a management interface LAG to be the FGSP session synchronization interface.
FortiView
Bug ID Description
838652 The FortiView Sessions monitor displays VDOM sessions from other VDOMs.
892798 WAD is crashing and CPU memory is spiking when loading FortiView.
GUI
Bug ID Description
440197 On the System > FortiGuard page, the override FortiGuard server for AntiVirus & IPS Updates
shows an Unknown status, even if the server is working correctly. This is a display issue only; the
override feature is working properly.
677806 On the Network > Interfaces page when VDOM mode is enabled, the Global view incorrectly shows
the status of IPsec tunnel interfaces from non-management VDOMs as up. The VDOM view shows
the correct status.
699508 When an administrator ends a session by closing the browser, the administrator timeout event is not
logged until the next time the administrator logs in.
722358 When a FortiGate local administrator is assigned to more than two VDOMs and tries logging in to
the GUI console, they get a command parse error when entering VDOM configuration mode.
753328 Incorrect shortcut name shown on the Network > SD-WAN > Performance SLAs page.
807197 High iowait CPU usage and memory consumption issues caused by report runner.
820909 On the Policy & Objects > Schedules page, when the end date of a one-time schedule is set to the
31st of a month, it gets reset to the 1st of the same month.
Workaround: use CLI to set schedules with an end date of 31st.
821030 Security Fabric root FortiGate is unable to resolve firewall object conflicts in the GUI.
821734 Log & Report > Forward Traffic logs do not show the Policy ID if there is no Policy Name.
822991 On the Log & Report > Forward Traffic page, using the filter Result : Deny(all) does not work as
expected.

Fortinet Inc.
Resolved issues
Bug ID Description
827893 Security rating test for FortiCare Support fails when connected to FortiManager Cloud or
FortiAnalyzer Cloud.
829736 Incorrect information is being displayed for the HA role on the System > HA page.
829773 Unable to load the Network > SD-WAN > SD-WAN Rules table sometimes due to a JavaScript error.
831439 On the WiFi & Switch Controller > SSIDs page, multiple DHCP servers for the same range can be
configured on an interface if the interface name contains a comma (,) character.
837048 Unable to delete the LAN interface's addresses without switching it back to a none-LAN role.
842079 On the System > HA page, a Failed to retrieve info caution message appears when hovering over
the secondary unit's Hostname. The same issue is observed on the Dashboard > Status > Security
Fabric widget.
845513 On G-model profiles, changing the platform mode change from single 5G (dedicated scan enabled)
to dual 5G is not taking effect.
853414 Policy and dashboard widgets do not load when the FortiGate manages a FortiSwitch with tenant
ports (exported from root to other VDOM).
854529 The local standalone mode in a VAP configuration is disabled when viewing or updating its settings
in the GUI.
861466 The Active Administrator Sessions widget shows the incorrect interface when accessing the firewall
through the GUI.
862474 IPsec tunnel interface Bandwidth widget inbound is zero and outbound value is lower than the
binding interface.
865956 On the Network > Policy Routes page, entries cannot be copied and pasted above or below.
866790 System > Firmware & Registration menu is not visible for administrator accounts without read-write
permissions for the sysgrp-permission category.
867802 GUI always displays Access denied error after logging in.
869138 Unable to select addresses in FortiView monitors.
869828 An httpsd crash occurs when the GUI fails to get the disk log settings from the FortiGate.
870675 CLI console in GUI reports Connection lost. when the administrator has more than 100 VDOMs
assigned.
874502 An access privilege prompt is not displayed when logging in to the GUI of a FortiGate managed by a
FortiManager with post-login-banner enabled. The user is logged in with read-only
permissions.
881678 On the Network > Routing Objects page, editing a prefix list with a large number of rule entries fails
with an error notification that The integer value is not within valid range.
889647 CLI console disconnects and has '/tmp/daemon_debug/node_...' crash.
890531 Node.JS boots earlier than autod, which leads to a Node.JS crash.

Fortinet Inc.
Resolved issues
Bug ID Description
890683 GUI being exposed to port 80 on the interfaces defined in the ACME settings, even if administrative
access is disabled on the interface.
891895 When remotely accessing the FortiGate from FortiGate Cloud, the web GUI console displays
Connection lost. Press Enter to start a new session.
897004 On rare occasions, the GUI may display blank pages when the user navigates from one menu to
another if there is a managed FortiSwitch present.
899434 A super_admin login is logged in the console logs when remotely logging in to a FortiGate with the
FortiCloud portal using a prof_admin profile.
HA
Bug ID Description
662978 Long lasting sessions are expired on HA secondary device with a 10G interface.
795443 The execute reboot script does not work in HA due to a HA failover before the script running is
done.
826790 DHCP over IPsec is not working in an FGSP cluster.
843837 HA A-P virtual cluster information is not correctly presented in the GUI and CLI.
852308 New factory reset box failed to synchronize with primary, which was upgraded from 7.0.
853900 The administrator password-expire calculation on the primary and secondary returns a one-
second diff, and causes HA to be out-of-sync.
854445 When adding or removing an HA monitor interface, the link failure value is not updated.
855841 In an HA A-P environment, an old administrator user still exists in the system after restoring the
backup.
856004 Telnet connection running ping fails during FGSP failover for virtual wire pair with VLAN traffic.
856643 FG-500E interface stops sending IPv6 RAs after upgrading from 7.0.5 to 7.0.7.
860497 Output of diagnose sys ntp status is misleading when run on a secondary cluster member.
864226 FG-2600F kernel panic occurs after a failover on both members of the cluster.
868622 The session is not synchronized after HA failover by detecting monitored interface as down.
869557 Upgrading or re-uploading an image to the HA secondary node causes the OS to be un-
certified.
870367 FGCP A-P devices get out of HA synchronization periodically due to FortiTokens being added and
deleted.
872431 Primary FortiGate synchronizes the changing HA command to the secondary.

Fortinet Inc.
Resolved issues
Bug ID Description
874823 FGSP session-sync-dev ports do not use L2 Ethernet frames but always use UDP, which
reduces the performance.
876178 hasync crashing with signal 6 after upgrading to 7.2.3 from 7.0.7.
878173 When downloading the speed test server list, the HA cluster gets and stays out-of-sync.
885245 Unexpected failover occurs due to uptime, even if the uptime difference is less than the ha-
uptime-diff-margin.
885844 HA shows as being out-of-sync after upgrading due to a checksum mismatch for endpoint-
control fctems.
Hyperscale
Bug ID Description
804742 After changing hyperscale firewall policies, it may take longer than expected for the policy changes
to be applied to traffic. The delay occurs because the hyperscale firewall policy engine
enhancements added to FortiOS may cause the FortiGate to take extra time to compile firewall
policy changes and generate a new policy set that can be applied to traffic by NP7 processors. The
delay is affected by hyperscale policy set complexity, the total number of established sessions to be
re-evaluated, and the rate of receiving new sessions.
807523 On NP7 platforms the config system npu option for nat46-force-ipv4-packet-
forwarding is missing.
810366 Unrelated background traffic gets impacted when changing a policy where a hyperscale license is
used.
824733 IPv6 traffic continues to pass through a multi-VDOM setup, even when the static route is deleted.
835697 Interface routes under DHCP mode remain in LPMD after moving the interface to another VDOM.
837270 Allowing intra-zone traffic is now supported in hyperscale firewall VDOMs. Options to block or allow
intra-zone traffic are available in the GUI and CLI.
841712 On FortiGates licensed for hyperscale firewall features, the config system setting options
nat46-force-ipv4-packet-forwarding and nat64-force-ipv6-packet-forwarding
now also apply to NP7-offloaded traffic. The config system npu option nat46-force-ipv4-
packet-forwarding has been removed.
877696 Get KTRIE invalid node related error and kernel panic on standby after adding a second device into
A-P mode HA cluster.

Fortinet Inc.
Resolved issues
Intrusion Prevention
Bug ID Description
839170 IPS engine may crash (SIGALRM)) when the system is busy because it might not receive enough
run time.
842073 High CPU usage for more than 20 minutes and cmdb deadlock after FortiGuard update.
856837 When flow mode AV is enabled, IPS engine memory usage is higher with a large number of flow
mode AV requests.
883600 Under config ips global, configuring set exclude-signatures none does not save to
backup configuration.
IPsec VPN
Bug ID Description
699973 IPsec aggregate shows down status on Interfaces, Firewall Policy, and Static Routes configuration
pages.
726326, IPsec server with NP offloading drops packets with an invalid SPI during rekey.
745331
788751 IPsec VPN Interface shows incorrect TX/RX counter.
797342 Users cannot define an MTU value for the aggregate VPN.
798045 FortiGate is unable to install SA (failed to add SA, error 22) when there is an overlap in
configured selectors.
810833 IPsec static router gateway IP is set to the gateway of the tunnel interface when it is not specified.
812229 A random four-character peer ID is displayed in the GUI and CLI when a VPN tunnel is formed using
IKEv2 if the peer ID is not configured.
828933 iked signal 11 crash occurs once when running a VPN test script.
842571 If mode-cfg is used, a race condition can result in an IP conflict and sporadic routing problems in
an ADVPN/SD-WAN network. Connectivity can only be restored by manually flushing the IPsec
tunnels on affected spokes.
848014 ESP tunnel traffic hopping from VRF.
849515 ADVPN dynamic tunnel is picking a tunnel ID that is within another VPN interface IP range.
852868 Issues with synchronization of the route information (using add-route option) on spokes during
HA failover that connect to dialup VPN.
855705 NAT detection in shortcut tunnel sometimes goes wrong.

Fortinet Inc.
Resolved issues
Bug ID Description
855772 FortiGate IPsec tunnel role could be incorrect after rebooting or upgrading, and causes negotiation
to be stuck when it comes up.
858681 When upgrading from 6.4.9 to 7.0.6 or 7.0.8, the traffic is not working between the spokes on the
ADVPN environment.
858697 Native IPsec iOS authentication failure using LDAP account with two-factor authentication.
858715 IPsec phase 2 fails when both HA cluster members reboot at the same time.
861195 In IPsec VPN, the fnbamd process crashes when the password and one-time password are entered
in the same Password field of the VPN client.
869166 IPsec tunnel does not coming up after the upgrading firmware on the branch FortiGate (FG-61E).
873097 Phase 2 not initiating the rekey at soft limit timeout on new kernel platforms.
876795 RADIUS server will reject new authentication if a previous session is missing ACCT-STOP to
terminate the session, which causes the VPN connection to fail.
882483 ADVPN spoke does not delete the BGP route entry to another spoke over IPsec when the IPsec
VPN tunnel is down.
885818 If a tunnel in an IPsec aggregate is down but its DPD link is on, the IPsec aggregate interface may
still forward traffic to a down tunnel causing traffic to drop.
887800 In an L2TP configuration, set enforce-ipsec enable is not working as expected after
upgrading.
891462 The Peer ID field in the IPsec widget should not show a warning message that Two-factor
authentication is not enabled.
892699 In an HA cluster, static routes via the IPsec tunnel interface are not inactive in the routing table when
the tunnel is down.
899822 IPsec dialup interface does not appear in the Interface dropdown when adding an Interface
Bandwidth widget.
Log & Report
Bug ID Description
755632 Unable to view or download generated reports in the GUI if the report layout is custom.
795272 Local out DNS traffic is generating forward traffic logs with srcintf "unknown-0".
823183 FortiGates are showing Logs Queued in the GUI after a FortiAnalyzer reboot, even tough the
queued logs were actually all uploaded to FortiAnalyzer and cleared when the connection restores.
825318 Archived Data tab is missing from intrusion prevention and application control log Details pane once
log-packet is enabled.

Fortinet Inc.
Resolved issues
Bug ID Description
828211 Policy ID filter is not working as expected.
829862 On the Log & Report > ZTNA Traffic page, the client's Device ID is shown as [object Object]. The
Log Details pane show the correct ID information.
836846 Packet captured by firewall policy cannot be downloaded.
838357 A deny policy with log traffic disabled is generating logs.
839601 When log pages are scrolled down, no logs are displayed after 500 lines of logs.
850519 Log & Report > Forward Traffic logs do not return matching results when filtered with !<application
name>.
857573 Log filter with negation of destination IP display all logs.
858304 When FortiGate Cloud logging is enabled, the option to display 7 days of logs is not visible on the
Dashboard > FortiView pages.
858589 Unable to download more than 500 logs from the FortiGate GUI.
860141 Syslog did not update the time after daylight saving time (DST) adjustment.
860264 The miglogd process may send empty logs to other logging devices.
860459 Unable to back up logs (FG-201E).
860487 Incorrect time and time zone appear in the forward traffic log when timezone is set to 18 (GMT-3
Brasilia).
861567 In A-P mode, when the link monitor fails, the event log displays a description of ha state is
changed from 0 to 1.
864219 A miglogd crash occurs when creating a dynamic interface cache on an ADVPN environment.
872181 On the Log & Report > Log Settings > Local Logs page, the Local reports and Historical FortiView
settings cannot be enabled.
872326 FortiGate cannot retrieve logs from FortiAnalyzer Cloud. Results are shown rarely.
873987 High memory usage from miglogd processes even without traffic.
879228 FortiAnalyzer override settings are not taking effect when ha-direct is enabled.
906888 Free-style filter not working as defined under config fortianalyzer override-filter.
Proxy
Bug ID Description
707827 The video filter does not display the proper replacement message when the user redirects to a
blocked video from the YouTube homepage or video recommendation list.
746587 WAD crashes during traffic scan in proxy mode.

Fortinet Inc.
Resolved issues
Bug ID Description
766158 Video filter FortiGuard category takes precedence over allowed channel ID exception in the same
category.
781613 WAD crash occurs four times on FG-61F during stress testing.
796150 WAD crashed many times on FG-61F during stress testing.
818371 WAD process crashes with some URIs.
823078 WAD user-info process randomly consumes 100% CPU of one core.
825977 WAD crash occurs on FG-101F during stress testing.
834387 In a firewall proxy policy, the SD-WAN zone assigned to interface is not checked.
835745 WAD process is crashing after upgrading to FortiOS 7.2.1.
843318 If a client sends an HTTP request for a resource which is not yet cached by the FortiGate and the
request header contains Cache-Control: only-if-cached, then the WAD worker process will
crash with signal 11.
853864 FortiGate out-of-band certificate check issue occurs in a proxy mode policy with SSL inspection.
854511 Unable to make API calls using Postman Runtime script after upgrading to 7.2.0.
855853 WAD crashes frequently and utilizes high CPU.
855882 Increase in WAD process memory usage after upgrading.
856235 The WAD process memory usage gradually increases over a few days, causing the FortiGate to
enter into conserve mode.
857368 An encoded HTTP header may be improperly handled, causing inadvertent disruption to traffic.
857507 When a server sends a connection close response too early, traffic from the client may be
interrupted inadvertently before the request is completed.
858148 Memory leak in WAD user info history daemon.
870151 WAD memory leak occurs on TCP port and HTTP tunnel session port.
870554 WAD crash occurs with explicit proxy when IPv6 is enabled.
874563 User information attributes can cause disruption when they are not properly merged.
880712 WAD crashed with signal 11.
885674 Unable to send logs from FortiClient to FortiAnalyzer when deep inspection is enabled on firewall
policy.
886284 Application WAD signal 11 crash occurs.

Fortinet Inc.
Resolved issues
REST API
Bug ID Description
725048 Improve performance for /api/v2/monitor/system/available-interfaces (phase 2).
847526 Able to add incomplete policies with empty mandatory fields using the REST API.
849273 /api/v2/monitor/system/certificate/download can still download already deleted CSR

files.
864393 High CPU usage of httpsd on FG-3600E HA system.
886012 Setting the MTU fails when a port is defined by the API.
892237 Updating the HA monitor interface using the REST API PUT request fails and returns a -37 error.
Routing
Bug ID Description
708904 No IGMP-IF for ifindex log points to multicast enabled interface.
724468 Router policy destination address not take effect when internet-service-id is configured.
821149 Early packet drop occurs when running UTM traffic on virtual switch interface.
827565 Using set load-balance-mode weight-based in SD-WAN implicit rule does not take effect
occasionally.
893603 GUI does not show gateway IP on the routing table page if VDOM mode is transparent.
846107 IPv6 VRRP backup is sending RA, which causes routing issues.
848310 IPsec traffic sourced from a loopback interface does not follow the policy route or SD-WAN rules.
850778 Spoke-to-spoke communication randomly breaks. The BGP route to reach the spoke subnet points
to the main ADVPN tunnel instead of the shortcut tunnel.
850862 When creating a new rule on the Network > Routing Objects page, the user cannot create a route
map with a rule that has multiple similar or different AS paths in the GUI.
860075 Traffic session is processed by a different SD-WAN rule and randomly times out.
862165 FortiGate does not add the route in the routing table when it changes for SD-WAN members.
862418 Application VWL crash occurs after FortiManager configuration push causes an SD-WAN related
outage.
862573 SD-WAN GUI does not load, and the lnkmtd process crashes frequently.
863318 Application forticron signal 11 (Segmentation fault) received.

Fortinet Inc.
Resolved issues
Bug ID Description
865914 When BSM carries multiple CRPs, PIM might use the incorrect prefix to update the mroute's RP
information.
870983 Unable to set local-as in BGP confederation configuration.
883918 Delay in joining (S,G) in PIM-SM.
884372 All BGP routes in dual ADVPN redundant configuration are not getting updated to the correct WAN
interface post-rollback to WAN failover.
890379 After upgrading, SD-WAN is unable to fail over the traffic when one interface is down.
897940 Link monitor's probe timeout value range is not appropriate when the user decreases the minimum
interval.
Security Fabric
Bug ID Description
753177 IoT device vulnerabilities should be included in security ratings.
809106 Security Fabric widget and Fabric Connectors page do not identify FortiGates properly in HA.
814796 The threat level threshold in the compromised host trigger does not work.
819192 After adding a Fabric device widget, the device widget does not appear in the dashboard.
825291 Security rating test for FortiAnalyzer fails when connected to FortiAnalyzer Cloud.
832015 Root FortiGate cannot finish the security rating with a large Fabric topology (more than 25 to 30
devices) because the REST API is not limited to the local network.
844412 When a custom LLDP profile has auto-isl disabled, the security rating test, Lockdown LLDP
Profile, fails.
848822 The FortiAP Firmware Versions and FortiSwitch Firmware Versions security rating tests fail
because the firmware version on the FortiAPs and FortiSwitches is not recognized correctly.
851656 Sessions with csf_syncd_log flag in a Security Fabric are not logged.
852340 Various places in the GUI do not show the secondary HA device.
862532 Unable to load topology pages for a specific Security Fabric topology on the root and downstream
FortiGates.
867313 Error triggering automation stitch message appears when the license expiry notification type is
FortiGuard Web Filter.
868701 In a simple cluster, the primary unit failed to upgrade to 7.2.3.
870527 FortiGate cannot display more than 500 VMs in a GCP dynamic address.

Fortinet Inc.
Resolved issues
Bug ID Description
875100 Unable to remove external resource in a certain VDOM when the external resource has no
reference in that VDOM.
880011 When the Security Fabric is enabled and admin-https-redirection is enabled on a

downstream FortiGate, the following GUI features do not work for the downstream FortiGate when
the administrator manages the downstream FortiGate using the root FortiGate's GUI:
l Web console access
l Diagnostic packet capture
l GUI notification when a new device joins or leaves the Security Fabric
l GUI notification if a configuration on the current page changes
These features still work for the root FortiGate's GUI.
885810 The gcpd daemon constantly crashes (signal 11 segmentation fault).
887967 Fabric crashes when synchronizing objects with names longer than 64 characters.
907172 Automation stitch with FortiDeceptor Fabric connector event trigger cannot be triggered.
SSL VPN
Bug ID Description
710657 The dstaddr/dstaddr6 of an SSL VPN policy can be set to all when split tunnel mode is
enabled and only the default portal is set.
719740 The No SSL-VPN policies exist warning should not be shown in the GUI when a zone that has
ssl.root as a member is set in an SSL VPN policy.
746440 When sending the SSL VPN settings email (VPN > SSL-VPN Settings > Send SSL-VPN
Configuration), the Email template only includes a hyperlink to the configuration, which is not
supported by Gmail and Fortinet email.
748085 Authentication request of SSL VPN realm can now only be sent to user group, local user, and
remote group that is mapped to that realm in the SSL VPN settings. The authentication request will
not be applied to the user group and remote group of non-realm or other realms.
787768 The web-mode setting should not be enabled when the portal is mapped in an SSL VPN policy
where a VIP is applied.
808107 FortiGate is not sending Accounting-Request packet that contains the Interim-Update AVP when
two-factor authentication is assigned to a user (defined on the FortiGate) while connecting using
SSL VPN.
810239 Unable to view PDF files in SSL VPN web mode.
819754 Multiple DNS suffixes cannot be set for the SSL VPN portal.
828194 SSL VPN stops passing traffic after some time.

Fortinet Inc.
Resolved issues
Bug ID Description
839261 On the VPN > SSL-VPN Settings page, when the source-address-negate option is enabled for
an address in the CLI, the GUI does not display an exclamation mark against that address entry in
the Hosts field.
This is cosmetic and does not affect on the FortiGate functionality or operation. The source-
address-negate option being enabled can be confirmed in the CLI.
850898 OS checklist for the SSL VPN in FortiOS does not include macOS Ventura (13).
852566 User peer feature for one group to match to multiple user peers in the authentication rules is broken.
854143 Unable to access Synology NAS server through SSL VPN web mode.
854642 Internal website with JavaScript is proxying some functions in SSL VPN web mode, which breaks
them.
856316 Browser displays an Error, Feature is not available message if a file larger than 1 MB is uploaded
from FTP or SMB using a web bookmark, even though the file is uploaded successfully. There are
no issues with downloading files.
856554 SSL VPN web mode top-right dropdown button (user profile menu) does not work.
859115 SSL VPN bookmark not accessible.
863860 RDP over SSL VPN web mode to a Windows Server changes the time zone to GMT.
864096 EcoStruxure Building Operations 2022 does not render using SSL VPN bookmark.
864417 In the second authentication of RADIUS two-factor authentication, the acct-update-interval

returned is 0. SSL VPN uses the second return and not send RADIUS acct-interim-update
packet.
867182 RDP/VNC host name is not encrypted when URL obscuration is enabled.
870061 Kernel does not delete original route after address assigned to the client changes.
873313 SSL VPN policy is ignored if no user or user group is set and the FSSO group is set.
873995 Problem with the internal website using SSL VPN web mode.
877896 When accessing the VDOM's GUI in SSL VPN web mode, policies are only shown for a specific
VDOM instead of all VDOMs.
884860 SSL VPN tunnel mode gets disconnected when SSL VPN web mode is disconnected by limit-
user-logins.
890876 One of the speed-connect website JavaScript files has trouble with host process.
Switch Controller
Bug ID Description
730472 FortiSwitch enabled VLANs with VLAN and proxy ARP access have large latencies on initial ARP
resolutions.

Fortinet Inc.
Resolved issues
Bug ID Description
762615, FortiSwitches managed by FortiGate go offline intermittently and require a FortiGate reboot to
765283 recover.
769722 Support FortiLink to recognize a FortiSwitch based on its name and not just by serial number.
853718 Layer 3 FortiLink does not come up after upgrading.
854104 FortiLink daemon keeps pushing the configuration to FortiSwitch for a long time when the
FortiSwitch is deleted and re-discovered.
857778 Switch controller managed switch port configuration changes do not take effect on the FortiSwitch.
858113 On the WiFi & Switch Controller > Managed FortiSwitches page, when an administrator with
restricted access permissions is logged in, the Diagnostics and Tools page for a FortiSwitch cannot
be accessed.
876021 FortiLink virtually managed switch port status is not getting pushed after the FortiGate reboots.
886887 When a MAC VLAN appears on the same MCLAG trunk, continuous event logs are received on
FortiGate and FortiAnalyzer.
System
Bug ID Description
550701 WAD daemon signal 11 causes cmdbsvr deadlock.
649729 HA synchronization packets are hashed to a single queue when sync-packet-balance is

enabled.
666664 Interface belonging to other VDOMs should be removed from interface list when configuring a
GENEVE interface.
700621 The forticron daemon is constantly being restarted.
709679 Get can not set mac address(16) error message when setting a MAC address on an
interface in HA that is already set.
713951 Not all ports are coming up after an LAG bounce on 8 × 10 GB LAG with ASR9K. Affected platforms:
FG-3960E and FG-3980E.
722273 SA is freed while its timer is still pending, which leads to a kernel crash.
724085 Traffic passing through an EMAC VLAN interface when the parent interface is in another VDOM is
blocked if NP7 offloading is enabled. If auto-asic-offload is disabled in the firewall policy, then
the traffic flows as expected.
729912 DNS proxy does not transfer the DNS query for IPv6 neighbor discovery (ND) when client devices
are using random MAC addresses, so one device can configure many IPv6 addresses.
748496 Wrong IP displayed in GUI widget if FortiGuard anycast AWS is used.

Fortinet Inc.
Resolved issues
Bug ID Description
776646 On the Network > Interfaces page, configuring a delegated interface to obtain the IPv6 prefix from
an upstream DHCPv6 server fails with an error notification (CLI internal error).
784169 When a virtual switch member port is set to be an alternate by STP, it should not reply with ARP;
otherwise, the connected device will learn the MAC address from the alternate port and send
subsequent packets to the alternate port.
790595 Improve dnsproxy process memory management.
799570 High memory usage occurs on FG-200F.
805122 In FIPS-CC mode, if cfg-save is set to revert, the system will halt a configuration change or
certificate purge.
807629 NP7 dos-offload triggers an established TCP session to have synproxy process issues.
810137 Scheduled speed test crash is caused by adding the same object to a list twice.
810879 DoS policy ID cannot be moved in GUI and CLI when multiple DoS policies are enabled.
812957 When setting the speed of 1G SFP ports on FG-180xF platforms to 1000full, the interface does
not come up after rebooting.
813607 LACP interfaces are flapping after upgrading.
815937 FCLF8522P2BTLFTN transceiver is not working after upgrade.
818897 The value of SNMP OID IP-MIB (RFC 4293) is inaccurate.
820268 VIP traffic access to the EMAC VLAN interface uses incorrect MAC address on NP7 platform.
826490 NP7 platforms may reboot unexpectedly when unable to handle kernel null pointer de-reference.
827240 FortiGate in HA may freeze and reboot. Before the reboot, softIRQ may be seen as high. This leads
to a kernel panic.
828129 A disabled EMAC VLAN interface is replying to a ping.
836409 When deleting a non-existing entry, the error code returned is not appropriate.
838933 DoS anomaly has incorrect threshold after loading a modified configuration file.
840960 When kernel debug level is set to >=KERN_INFO on NP6xLite platforms, some tuples missing
debug messages may get flooded and cause the system to get stuck.
845736 After rebooting the FortiGate, the MTU value on the VXLAN interface was changed.
847314 NP7 platforms may encounter random kernel crash after reboot or factory reset.
850683 Console keeps displaying bcm_nl.nr_request_drop ... after the FortiGate reboots because
of the cfg-save revert setting under config system global. Affected platforms: FG-10xF
and FG-20xF.
850688 FG-20xF system halts if setting cfg-save to revert under config system global and after
the cfg-revert-timeout occurs.
852562 Huge configuration files cause delays during the booting process.

Fortinet Inc.
Resolved issues
Bug ID Description
853144 Network device kernel null pointer is causing a kernel crash.
853794 Issue with the server_host_key_algorithm compatibility when using SSH on SolarWinds.
853811 Fortinet 10 GB transceiver LACP flapping when shut/no shut was performed on the interface from
the switch side.
854388 Configuring set src-check disable is not persistent in the kernel after rebooting for GRE
interfaces.
855573 False alarm of the PSU2 occurs with only one installed.
855775 Time zone for Kyiv, Ukraine is missing.
856202 Random reboots and kernel panic on NP7 cluster when the FortiGate sends a TCP RST packet and
IP options are missing in the header.
859717 The FortiGate is only offering the ssh-ed25519 algorithm for an SSH connection.
859795 High CPU utilization occurs when relay is enabled on VLAN, and this prevents users from getting an
IP from DHCP.
860052 The 40G/100G port goes down on FG-260xF when upgrading to 7.2.
860385 IPv6 BGP session drops when passing through a FortiGate configured with VRF.
862941 GUI displays a blank page if vdom-admin user has partial permissions.
867435 FG-400E-BP has crash at initXXXXXXXXXXX[1]: segfault at 3845d5a after package

validation fails.
867978 Subnet overlap error occurs when configuring the same IPv4 link-local addresses on two different
interfaces.
868225 After a cold reboot (such as a power outage), traffic interfaces may not come up with a possible loss
of VLAN configurations.
868821 execute ssh-regen-keys should be global-level command.
869599 Forticron memory is leaking.
870381 Memory corruption or incorrect memory access when processing a bad WQE.
875868 HQIP test fails on FG-2201E.
876403 ACME auto-renewal is not performed after HA failover.
876853 No output of execute sensor list is displayed after rebooting.
876874 The Dashboard > Status > Sensor Information widget does not load.
877039 On the Network > BGP page, creating or editing a table entry increases memory consumption of the
FortiGate to 99%.
877154 FortiGate with new kernel crashes when starting debug flow.
877240 Get zip conf file failed -1 error message when running a script configuring the FortiGate.

Fortinet Inc.
Resolved issues
Bug ID Description
878400 When traffic is offloaded to an NP7 source MAC, the packets sent from the EMAC VLAN interface
are not correct.
880290 NP7 is not configured properly when the ULL ports are added to LAG interface, which causes
accounting on the LAG to not work.
881094 FG-3501F NP7 is dropping all traffic after it is offloaded.
882187 FortiGate enters conserve mode in a few hours after enabling UTM on the policies.
883071 Kernel panic occurs due to null pointer dereference.
887772 High CPU usage after upgrade to 7.2.4, WAD crashes continuously.
889634 Unable to configure IPv6 setting on system interface (FWF-81F-2R-POE).
891841 Unable to handle kernel NULL pointer dereference at 0000000000000000 for NP7 device; the
device keeps rebooting.
899884 FG-3000F reboots unexpectedly with NULL pointer dereference.
909345 Kernel panic occurs when receiving ICMP redirect messages.
Upgrade
Bug ID Description
850691 The endpoint-control fctems entry 0 is added after upgrading from 6.4 to 7.0.8 when the
FortiGate does not have EMS server, which means the endpoint-control fctems feature was
not enabled previously. This leads to a FortiManager installation failure.
892647 Static route configurations were lost upgrading from 7.0.7 to 7.2.3.
900761 FG-601E crashes randomly after upgrading to 7.0.8 and 7.0.11.
User & Authentication
Bug ID Description
751763 When MAC-based authentication is enabled, multiple RADIUS authentication requests may be sent
at the same time. This results in duplicate sessions for the same device.
823884 Searching in User & Authentication > User Definition shows results from other groups.
843528 RADIUS MAC authentication using ClearPass is intermittently using old credentials.
846545 LDAPS connectivity test fails with old WinAD after OpenSSL was upgraded to 3.0.2.

Fortinet Inc.
Resolved issues
Bug ID Description
853793 FG-81F 802.1X MAC authentication bypass (MAB) failed to authenticate Cisco AP.
855898 All devices are detected as Other identified device in the Device Inventory widget.
856370 The EAP proxy worker application crashes frequently.
857438 SSL VPN group matching does not work as expected for Azure auto login.
858961 Client's firewall authentication session timeout is set to 900 when it passes MAC authentication
bypass by ping.
859845 In some cases, the proper hostnames are not showing up when looking at APs on the FortiSwitch
ports screen.
864703 ACME client fails to work with some CA servers.
865166 A cid scan crash occurs when device detections happen in a certain order.
867225 ARP does not trigger FortiGuard device identification query.
VM
Bug ID Description
740796 IPv6 traffic triggers <interface>: hw csum failure message on CLI console.
856645 Session is not crated over NSX imported object when traffic starts to flow.
859165 Unable to enable FIPS cipher mode on FG-VM-ARM64-AWS.
859589 VPNs over Oracle Cloud stop processing traffic.
860096 CPU spike observed on all the cores in a GCP firewall VM.
868698 During a same zone AWS HA failover, moving the secondary IP will cause the EIP to be in a
disassociated state.
869359 Azure auto-scale HA shows certificate error for secondary VM.
878074 FG-ARM64-GCP and FG-ARM64-AZURE have HA synchronization issue with internal IP after
failover.
881728 Kernel hangs on FG-VM64-AZURE.
883203 FG-AWS SDN is unable to retrieve EKS cluster information, even thought its role is trusted by the
EKS role.
883896 Backup virtual server not working as expected (ERR_EMPTY_RESPONSE).
885829 Azure SDN connector stopped processing when Azure returned NotFound error for VMSS
interface from an AD DS-managed subscription.
890278 FG-VM Rackspace On-Demand upgrade from 7.2.3 to 7.2.4 breaks the pay-as-you-go license, and
reverts it to an evaluation license.

Fortinet Inc.
Resolved issues
Bug ID Description
902816 Azure kernel panic occurs after a failover on the cluster.
912184 RIP: 0010:storvsc_queuecommand+0x57d/0x is observed after deploying an FG-VM64-

AZURE in Standard_DS4_v2 size.
VoIP
Bug ID Description
757477 PRACK will cause voipd crashes when the following conditions are met: block-unknown is
disabled in the SIP profile, the PRACK message contains SDP, and PRACK fails to find any related
previous transactions (this is not a usual case).
Web Filter
Bug ID Description
766126 Block replacement page is not pushed automatically to replace the video content when using a
video filter.
856793 In flow mode, URL filter configuration changes cause a spike in CPU usage of the IPS engine
process.
863728 The urlfilter process causes a memory leak, even when the firewall policy is not using the web filter
feature.
878442 FortiGuard block page image (logo) is missing when the Fortinet-Other ISDB is used.
WiFi Controller
Bug ID Description
807605 FortiOS exhibits segmentation fault on hostapd on the secondary controller configured in HA.
821320 FG-1800F drops wireless client traffic in L2 tunneled VLAN with capwap-offload enabled.
825182 The 6 GHz channel lists should be updated according to the latest WiFi country region channels
map.
828901 Connectivity loss occurs due to switch and FortiAPs (hostapd crash).
831736 Application hostapd crash found on FG-101F.

Fortinet Inc.
Resolved issues
Bug ID Description
834644 A hostapd process crash is shown in device crash logs.
835783 CAPWAP traffic is not offloaded when re-enabling capwap-offload.
837130 Wireless client shows portal related webpage while doing MAC authentication with MAB mode.
846730 Dynamic VLAN assignment is disabled in the GUI when editing an SSID with radius mac-auth
and dynamic-vlan enabled.
856038 The voice-enterprise value changed after upgrading.
856830 HA FortiGate encounters multiple hostapd crashes.
857084 Hostapd segmentation fault signal 6 occurs upon HA failover.
857140 Hostapd segmentation fault signal 11 occurs upon RF chamber setup.
857975 The cw_acd process appears to be stuck, and is sending several access requests for MAC
authentication.
858653 Invalid wireless MAC OUI detected for a valid client on the network.
861552 Wireless client gets disconnect from WiFi if it is connected to a WPA2 SSID more than 12 hours.
865260 Incorrect source IP used in the self-originating traffic to RADIUS server.
868022 Wi-Fi clients on a RADIUS MAC MPSK SSID get prematurely de-authenticated by the secondary
FortiGate in the HA cluster.
882551 FortiWiFi fails to act as the root mesh AP, and leaf AP does not come online.
891625 Quarantined STA connected to a long interface name VAP is not moved to quarantined VLAN 4093.
892575 MPSK SSID with mpsk-schedules stopped working after the system time was changed due to
daylight saving time.
ZTNA
Bug ID Description
832508 The EMS tag name (defined in the EMS server's Zero Trust Tagging Rules) format changed in 7.2.1
from FCTEMS<serial_number>_<tag_name> to EMS<id>_ZTNA_<tag_name>.
After upgrading from 7.2.0 to 7.2.1, the EMS tag format was converted properly in the CLI
configuration, but the WAD daemon is unable to recognize this new format, so the ZTNA traffic will
not match any ZTNA policies with EMS tag name checking enabled.
859421 ZTNA server (access proxy VIP) is causing all interfaces that receive ARP request to reply with their
MAC address.
863057 ZTNA real server address group gets unset once the FortiGate restarts.

Fortinet Inc.
Resolved issues
Bug ID Description
865316 Adding an EMS tag on the Policy & Objects > Firewall Policy edit page for a normal firewall policy
forces NAT to be enabled.
875589 WAD crash observed when a client EMS tag changes.
887307 WAD crashes after upgrading to 7.2 (build 1336 and later).

Fortinet Inc.
Known issues
The following issues have been identified in version 7.2.5. To inquire about a particular bug or report a bug, please
contact Customer Service & Support.
Anti Virus
Bug ID Description
908706 On the Security Profiles > AntiVirus page, a VDOM administrator with a custom administrator profile
cannot create or modify an antivirus profile belonging to the VDOM.
Workaround: set the VDOM administrator profile to super_admin.
Explicit Proxy
Bug ID Description
817582 When there are many users authenticated by an explicit proxy policy, the Firewall Users widget can
take a long time to load. This issue does not impact explicit proxy functionality.
877337 HTTPS requests over IPv6 are not matched sometimes to the proxy policy when the IPv6 Internet
Service Database is applied in the proxy policy.
894557 In some cases, the explicit proxy policy list can take a long time to load due to a delay in retrieving
the proxy statistics. This issue does not impact explicit proxy functionality.
Workaround: restart the WAD process, or update the number of WAD processors.
set wad-worker-count <integer>
end
Firewall
Bug ID Description
843554 If the first firewall service object in the service list (based on the order in the command line table) has
a protocol type of IP, the GUI may incorrectly modify its protocol number whenever a new firewall
service of the same protocol type IP is created in the GUI.

Fortinet Inc.
Known issues
Bug ID Description
This silent misconfiguration can result in unexpected behavior of firewall policies that use the
impacted service. For example, some 6K and 7K platforms have firewall service ALL (protocol type
IP) as the first service, and this can cause the ALL service to be modified unexpectedly.
Workaround: create a new service in the CLI, or move a non-IP type services to the top of the
firewall service list. For example, if ALL is the first firewall service in the list:
config firewall service custom
edit "unused"
set tcp-portrange 1
next
move "unused" before "ALL"
end
FortiGate 6000 and 7000 platforms
Bug ID Description
887946 UTM traffic is blocked by an FGSP configuration with asymmetric routing.
888447 In some cases, the FortiGate 7000F platform cannot correctly reassemble fragmented packets.
896758 Virtual clustering is not supported by FortiGate 6000 and 7000 platforms.
897629 The FortiGate 6000 and 7000 platforms do not support EMAC VLANs.
901695 On FortiGate 7000F platforms, NP7-offloaded UDP sessions are not affected by the udp-idle-
timer option of the config system global command.
906481 The GUI becomes unresponsive, and sometimes may work after rebooting.
907140 Authenticated users are not synchronized to the secondary FortiGate 6000 or 7000 chassis when
the secondary chassis joins a primary chassis to form an FGCP cluster.
907695 The FortiGate 6000 and 7000 platforms do not support IPsec VPN over a loopback interface or an
NPU inter-VDOM link interface.
908576 On a FortiGate 7000F, after a new FPM becomes the primary FPM, IPsec VPN dynamic routes are
not synchronized to the new primary FPM.
Workaround: reset IPsec VPN tunnels that use dynamic routing.
908674 Sessions for IPsec dialup tunnels that are configured to be handled by a specific FPC or FPM may
be incorrectly sent to a different FPC or FPM, resulting in traffic being blocked.
909163 Local logging support is needed on all SLBC models.
910883 The FortiGate 6000s or 7000s in an FGSP cluster may load balance FTP data sessions to different
FPCs or FPMs. This can cause delays while the affected FortiGate 6000 or 7000 re-installs the
sessions on the correct FPC or FPM.
911244 FortiGate 7000E IPv6 routes may not be synchronized correctly among FIMs and FPMs.

Fortinet Inc.
Known issues
Bug ID Description
918795 An uncertified warning appears only on the secondary chassis' FIM02 and FPMs.
920925 Graceful upgrade from 7.0.12 to 7.2.5 fails sometimes due to the primary chassis not being
switched over.
921452 After an SNMP HA failover, the SNMP trap continues to work.
GUI
Bug ID Description
825598 A Node exiting due to unhandled rejection: TypeError [ERR_INVALID_URL]:

Invalid URL error message appears in the debug crash log for the node process. This error does
not impact the GUI operation.
853352 On the View/Edit Entries slide-out pane (Policy & Objects > Internet Service Database dialog),
users cannot scroll down to the end if there are over 100000 entries.
898902 In the System > Administrators dialog, when there are a lot of VDOMs (over 200), the dialog can
take more than one minute to load the Two-factor Authentication toggle. This issue does not affect
configuring other settings in the dialog.
Workaround: use the CLI to configure two-factor-authentication under config system
admin.
HA
Bug ID Description
818432 When private data encryption is enabled, all passwords present in the configuration fail to load and
may cause HA failures.
Hyperscale
Bug ID Description
802182 A cmdb_txn_cache_data(query=log.npu-server,leve=1) failed error is seen after

editing an interface's VLAN ID.
843197 Output of diagnose sys npu-session list/list-full does not mention policy route
information.

Fortinet Inc.
Known issues
Bug ID Description
853258 Packets drop, and different behavior occurs between devices in an HA pair with ECMP next hop.
872146 The diagnose sys npu-session list command shows an incorrect policy ID when traffic is
using an intra-zone policy.
920228 NAT46 NPU sessions are lost and traffic drops when a HA failover occurs.
IPsec VPN
Bug ID Description
916260 The IPsec VPN tunnel list can take more than 10 seconds to load if the FortiGate has large number
of tunnels, interfaces, policies, and addresses. This is a GUI display issue and does not impact
tunnel operation.
Log & Report
Bug ID Description
860822 When viewing logs on the Log & Report > System Events page, filtering by domain\username does
not display matching entries.
Workaround: use a double backslash (domain\\username) while filtering or searching by username
only without the domain.
Proxy
Bug ID Description
837724 WAD crash occurs.
Routing
Bug ID Description
907386 BGP neighbor group configured with password is not working as expected.

Fortinet Inc.
Known issues
SSL VPN
Bug ID Description
795381 FortiClient Windows cannot be launched with SSL VPN web portal.
Switch Controller
Bug ID Description
904640 When a FortiSwitch port is reconfigured, the FortiGate may incorrectly retain old detected device
data from the port that results in an unexpected number of detected device MACs for the port. Using
diagnose switch-controller mac-cache show to check the device data can result in the
Device Information column being blank on the WiFi & Switch Controller > FortiSwitch Ports page or
in the Assets widget.
Workaround: disable the device retention cache to remove old device data.
config switch-controller global
set mac-retention-period 0
end
911232 Security rating shows an incorrect warning for unregistered FortiSwitches on the WiFi & Switch
Controller > Managed FortiSwitches.
Workaround: select a FortiSwitch and use the Diagnostics & Tools tooltip to view the correct
registration status.
System
Bug ID Description
884023 When a user is logged in as a VDOM administrator with restricted access and tries to upload a
certificate (System > Certificates), the Create button on the Create Certificate pane is greyed out.
887940 Status light is not showing on the FortiGate 60F or 100F after a cold reboot.
Web Filter
Bug ID Description
885222 HTTP session is logged as HTTPS in web filter when VIP is used.

Fortinet Inc.
Known issues
WiFi Controller
Bug ID Description
814541 When there are extra large number of managed FortiAP devices (over 500) and large number of
WiFi clients (over 5000), the Managed FortiAPs page and FortiAP Status widget can take a long
time to load. This issue does not impact FortiAP operation.
869106 The layer 3 roaming feature may not work when the wireless controller is running multiple cw_acd
processes (when the value of acd-process-count is not zero).
869978 CAPWAP tunnel traffic over tunnel SSID is dropped when offloading is enabled.
873273 The Automatically connect to nearest saved network option does not work as expected when FWF-
60E client-mode local radio loses connection.
903922 Physical and logical topology is slow to load when there are a lot of managed FortiAP (over 50). This
issue does not impact FortiAP management and operation.
904349 Unable to create FortiAP profile in the GUI for dual-5G mode FortiAP U231F/U431F models.
Workaround: use the CLI to update the profile to dual-5G mode.

Fortinet Inc.
Built-in AV engine
Built-in AV engine
Resolved engine issues
Bug ID Description
886780 Explicit proxy does not block MSI file type in file filter.

Fortinet Inc.
Built-in IPS engine
Built-in IPS engine
Resolved engine issues
Bug ID Description
835757 IPS Engine 6.004.133 crashes with signal 11.
839671 IPS engine is crashing.
847129 IPS engine crashes and FortiGate enters conserve mode. IPS engine stalled and IPS fail-open is
triggered.
867569 IPS engine crashes and FortiGate enters conserve mode when testing high loads of DNS traffic.
872397 After 7.0.5 upgrade, application is working when IPS and UTM is applied.
872747 CPU utilization reaches 99% due to IPS process and ipsengine has a signal 11 crash.
873608 DLP blocking of SMB traffic gives unreliable results.
877456 appcat="unknown" appears in traffic logs for the first traffic request after running diagnose ips
share clear all.
878755 HTTPS performance drops when IPS and deep inspection(flow-based) are configured in firewall
policy.
879555 FortiGate is querying the web filtering service over 2.5 billion times per day.
883545 Memory used by IPS engine due to a port scan attack not being released when the attack is
stopped.
885365 Some IPS signatures show all protocol in the GUI and CLI when FortiGuard has them as TCP, UDP.
890065 IPS Engine 6.00155 is crashing with signal 11 (segmentation fault).
893335 IPS Engine 7.2.309 crashed on FG-200E during stress testing.
893947 Unable to block archive bomb.
893962 When using FortiGuard remote category threat feed in FQDN format, some websites are not
blocked/allowed as expected.
895991 The CPU processing performance of IPS Engine 6.00156 is degraded in IPS and deep-inspection
(flow-based).
900323 IPS engine 7.001.142 crashes with signal 11.
901222 Web filter warning block page for FortiGuard categories is not displayed for HTTP2 with flow-based
and deep inspection.
902857 FortiGate does not forward TLS ServerHello to client when IPS is enabled with flow mode and deep
inspection.

Fortinet Inc.
Built-in IPS engine
Bug ID Description
908682 First HTTPS attempt with infected EICAR file cannot be blocked by IPS Engine 7.166 in a flow mode
AV profile.
910002 DNS translation does not work as expected after disabling Log all DNS queries and responses (set
log-all-domain disable).
912577 DNS queries (A/AAAA) from Linux have timeouts and delays.
916992 DNS static filter does not work as expected if it is the only setting in the DNS profile.

Fortinet Inc.
Limitations
Citrix XenServer limitations
The following limitations apply to Citrix XenServer installations:

l XenTools installation is not supported.
l FortiGate-VM can be imported or deployed in only the following three formats:
l XVA (recommended)
l VHD
l OVF
l The XVA format comes pre-configured with default configurations for VM name, virtual CPU, memory, and virtual
NIC. Other formats will require manual configuration before the first power on process.
Open source XenServer limitations
When using Linux Ubuntu version 11.10, XenServer version 4.1.0, and libvir version 0.9.2, importing issues may arise
when using the QCOW2 format and existing HDA issues.

Fortinet Inc.
www.fortinet.com
Copyright© 2023 Fortinet, Inc. All rights reserved. Fortinet®, FortiGate®, FortiCare® and FortiGuard®, and certain other marks are registered trademarks of Fortinet, Inc., and other Fortinet names herein
may also be registered and/or common law trademarks of Fortinet. All other product or company names may be trademarks of their respective owners. Performance and other metrics contained herein were
attained in internal lab tests under ideal conditions, and actual performance and other results may vary. Network variables, different network environments and other conditions may affect performance
results. Nothing herein represents any binding commitment by Fortinet, and Fortinet disclaims all warranties, whether express or implied, except to the extent Fortinet enters a binding written contract,
signed by Fortinet’s General Counsel, with a purchaser that expressly warrants that the identified product will perform according to certain expressly-identified performance metrics and, in such event, only
the specific performance metrics expressly identified in such binding written contract shall be binding on Fortinet. For absolute clarity, any such warranty will be limited to performance in the same ideal
conditions as in Fortinet’s internal lab tests. Fortinet disclaims in full any covenants, representations, and guarantees pursuant hereto, whether express or implied. Fortinet reserves the right to change,
modify, transfer, or otherwise revise this publication without notice, and the most current version of the publication shall be applicable.

Fortios v7.2.5 Release Notes

Uploaded by

Copyright:

Available Formats

Fortios v7.2.5 Release Notes

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fortios v7.2.5 Release Notes

Uploaded by

Copyright:

Available Formats

Release Notes

FORTINET VIDEO GUIDE

CUSTOMER SERVICE & SUPPORT

FORTINET TRAINING & CERTIFICATION PROGRAM

FORTINET TRAINING INSTITUTE

END USER LICENSE AGREEMENT

June 12, 2023

FortiOS 7.2.5 Release Notes 3

FortiOS 7.2.5 Release Notes 4

Date Change Description

2023-06-08 Initial release.

FortiOS 7.2.5 Release Notes 5

FortiOS 7.2.5 supports the following models.

FortiGate FG-40F, FG-40F-3G4G, FG-60E, FG-60E-DSL, FG-60E-DSLJ, FG-60E-POE, FG-60F, FG-

FortiWiFi FWF-40F, FWF-40F-3G4G, FWF-60E, FWF-60E-DSL, FWF-60E-DSLJ, FWF-60F, FWF-

FortiGate Rugged FGR-60F, FGR-60F-3G4G, FGR-70F, FGR-70F-3G4G

FortiFirewall FFW-3980E, FFW-VM64, FFW-VM64-KVM

FortiGate VM FG-ARM64-AWS, FG-ARM64-AZURE, FG-ARM64-GCP, FG-ARM64-KVM, FG-ARM64-

Pay-as-you-go FOS-VM64, FOS-VM64-HV, FOS-VM64-KVM, FOS-VM64-XEN

FortiGate 6000 and 7000 support

FG-6000F FG-6300F, FG-6301F, FG-6500F, FG-6501F

FG-7000E FG-7030E, FG-7040E, FG-7060E

FG-7000F FG-7081F, FG-7121F

FortiOS 7.2.5 Release Notes 6

l IPsec phase 1 interface type cannot be changed after it is configured on page 7

IPsec phase 1 interface type cannot be changed after it is

IP pools and blackhole route configuration

FortiGate 6000 and 7000 incompatibilities and limitations

FortiOS 7.2.5 Release Notes 7

Hyperscale incompatibilities and limitations

Remove support for SHA-1 certificate used for web management

FortiOS 7.2.5 Release Notes 8

742365 Prior to this enhancement, a ZTNA configuration required configuring:

l A ZTNA server configuration

l A ZTNA rules (proxy policy)

l An authentication scheme and rules (optional)

FortiOS 7.2.5 Release Notes 9

l When an interface role is changed from a non-LAN role to a LAN role.

FortiOS 7.2.5 Release Notes 10

870538 Increase firewall.address, firewall.service.group, and firewall.policy table size

FortiOS 7.2.5 Release Notes 11

More detailed information is available in the New Features Guide.

The existing documentation related links have been renamed:

l The Online Help link is renamed to Relevant Documentation.

FortiOS 7.2.5 Release Notes 12

812993 Support the blocking of a discovered FortiExtender device on a FortiGate configured as a

FortiOS 7.2.5 Release Notes 13

# diagnose sys npu-session list-brief6

FortiOS 7.2.5 Release Notes 14

849515 Add auto-discovery-crossover option under config vpn ipsec phase1-interface to

When auto-discovery-crossover is set to block on the auto-discovery sender:

tunnel have different network IDs.

the shortcut query message.

l If cross-over is not allowed on any side:

855520 Harden REST API and GUI access.

FortiOS 7.2.5 Release Notes 15

FortiOS 7.2.5 Release Notes 16

config wireless-controller wtp-group

FortiOS 7.2.5 Release Notes 17

To view supported upgrade path information: