STIHL MS 500i Instruction Manual

English

Contents

8.2 Fueling the Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
9 Starting and Stopping the Engine . . . . . . . . . . . . . . . . . . 20
2 Guide to Using this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 2
9.1 Starting the Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Translation of Original Instruction

2.1 Symbols used with warnings in the text . . . . . . . . . . . . . . 2

9.2 Stopping the Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.2 Symbols in Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
10 Checking the Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
10.1 Checking the Chain Sprocket . . . . . . . . . . . . . . . . . . . . . . 21
3.1 Chainsaw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
10.2 Checking the Guide Bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
10.3 Checking the Saw Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.3 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Manual

10.4 Testing the Chain Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 10.5 Checking the Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.1 Warning Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 10.6 Checking Chain Lubrication . . . . . . . . . . . . . . . . . . . . . . . . 23
4.2 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Printing inks contain vegetable oils, paper can be recycled.

11 Operating the Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4.3 The Operator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
11.1 Adjusting Oil Feed Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.4 Clothing and Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
11.2 Holding and Controlling the Chainsaw. . . . . . . . . . . . . . 24
4.5 Work Area and Surroundings . . . . . . . . . . . . . . . . . . . . . . . . 7
11.3 Sawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.6 Safe Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
11.4 Limbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.7 Fuel Mixture and Refueling . . . . . . . . . . . . . . . . . . . . . . . . . . 9
11.5 Felling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.8 Working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
12 After Finishing Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Printed on chlorine-free paper

4.9 Reactive Forces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.10 Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 12.1 After Finishing Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.11 Storing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 13 Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.12 Cleaning, Maintenance and Repairs . . . . . . . . . . . . . . . . 14 13.1 Transporting the Chainsaw. . . . . . . . . . . . . . . . . . . . . . . . . 30
5 Preparing the Saw for Operation . . . . . . . . . . . . . . . . . . . 15 14 Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.1 Preparing the Saw for Operation . . . . . . . . . . . . . . . . . . . 15 14.1 Storing the Chainsaw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6 Assembling the Saw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 15 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.1 Mounting and Removing the Bar and Chain. . . . . . . . . 15 15.1 Cleaning the Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.2 Tensioning the Saw Chain. . . . . . . . . . . . . . . . . . . . . . . . . . 16 15.2 Cleaning the Bar and Chain . . . . . . . . . . . . . . . . . . . . . . . . 31
6.3 Filling Up with Chain Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 15.3 Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.4 Mounting the Spiked Bumper . . . . . . . . . . . . . . . . . . . . . . . 18
© ANDREAS STIHL AG & Co. KG 2019

15.4 Cleaning the Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

7 Engaging and Disengaging the Chain Brake . . . . . . . . 18 16 Maintenance . . . . . . . . . . . . . . . .. .. .... .. .. .. ........ . . 33
7.1 Engaging the Chain Brake. . . . . . . . . . . . . . . . . . . . . . . . . . 18 16.1 Maintenance Intervals . . . . . .. .. .... .. .. .. ........ . . 33
0458-809-0121-A. VA3.A19.

7.2 Disengaging the Chain Brake. . . . . . . . . . . . . . . . . . . . . . . 18 16.2 Deburring the Guide Bar . . . .. .. .... .. .. .. ........ . . 33
0000008111_006_GB

8 Mixing Fuel and Refueling the Chainsaw . . . . . . . . . . . 18 16.3 Sharpening the Saw Chain . .. .. .... .. .. .. ........ . . 33
8.1 Mixing Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 17 Repairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process
with electronic systems.

0458-809-0121-A 1
English 1 Introduction

17.1 Repairing the Chain Saw, Guide Bar and Saw

Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 1 Introduction
18 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
18.1 Troubleshooting Chainsaw . . . . . . . . . . . . . . . . . . . . . . . . . 35 Dear Customer,
18.2 Clearing the Combustion Chamber . . . . . . . . . . . . . . . . . 36 Thank you for choosing STIHL. We develop and
19 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 manufacture our quality products to meet our customers’
19.1 STIHL MS 500i Chainsaw . . . . . . . . . . . . . . . . . . . . . . . . . . 37 requirements. The products are designed for reliability even
19.2 Chain Sprockets and Chain Speeds . . . . . . . . . . . . . . . . 37 under extreme conditions.
19.3 Minimum Groove Depth of Guide Bars . . . . . . . . . . . . . 37 STIHL also stands for premium service quality. Our
19.4 Noise and Vibration Data. . . . . . . . . . . . . . . . . . . . . . . . . . . 37 specialist dealers guarantee competent advice and
19.5 REACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 instruction as well as comprehensive service support.
19.6 Exhaust Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 We thank you for your confidence in us and hope you will
20 Bar and Chain Combinations . . . . . . . . . . . . . . . . . . . . . . . 38 enjoy working with your STIHL product.
20.1 STIHL MS 500i Chainsaw . . . . . . . . . . . . . . . . . . . . . . . . . . 38
21 Spare Parts and Accessories . . . . . . . . . . . . . . . . . . . . . . . 39
21.1 Spare Parts and Accessories. . . . . . . . . . . . . . . . . . . . . . . 39
22 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
22.1 Disposing of Chainsaw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Dr. Nikolas Stihl
23 EC Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . 39
23.1 STIHL MS 500i Chainsaw . . . . . . . . . . . . . . . . . . . . . . . . . . 39
IMPORTANT: READ BEFORE USE AND KEEP IN A SAFE
PLACE.

2 Guide to Using this Manual

2.1 Symbols used with warnings in the text

WARNING
This symbol indicates dangers that can cause serious
injuries or death.
► The measures indicated can avoid serious injuries or
death.

2 0458-809-0121-A
3 Overview English

NOTICE 3 Overview
This symbol indicates dangers that can cause damage to
property.
► The measures indicated can avoid damage to property. 3.1 Chainsaw

2.2 Symbols in Text

1
This symbol refers to a chapter in this instruction
manual. 2
#
3

87
6
9 11 5
10 4

31 12 13 17 18
14 15
16

30
29
19
20

0000-GXX-5816-A0
23
28 27
26 25 24 22 21

0458-809-0121-A 3
English 3 Overview

1 Front Hand Guard 15 Spark Plug Boot

Helps protect operator’s left hand from contact with the Connects ignition lead to spark plug
saw chain, serves to engage the chain brake and
activates the chain brake by inertia in certain kickback 16 Air Filter
situations. Filters the air entering the engine.

2 Muffler 17 Filter Cover

Reduces chainsaw noise emissions. Covers the air filter.

3 Spiked Bumper 18 Filter Cover Lock

Toothed stop for holding saw steady against wood while Secures filter cover to chainsaw.
cutting. 19 Throttle Trigger Lockout
4 Saw Chain Unlocks the throttle trigger.
Cuts the wood. 20 Control Handle
5 Guide Bar For operating, holding and controlling the chainsaw.
Supports and guides the saw chain. 21 Rear Hand Guard
6 Chain Catcher Protects operator’s right hand from contact with the chain
Reduces risk of operator contact with the chain if it if it comes off the bar or breaks.
comes off the bar or breaks. 22 Throttle Trigger
7 Tensioning Screw Controls engine speed.
Adjusts chain tension. 23 Stop Switch
8 Chain Sprocket Shuts off the engine.
Toothed wheel that drives the chain. 24 Manual Fuel Pump
9 Chain Sprocket Cover Eases engine starts.
Covers the chain sprocket and secures the guide bar to 25 Fuel Tank Cap
the chainsaw. Closes the fuel tank.
10 Nuts 26 Starter Grip
Secure chain sprocket cover to the chainsaw. Serves to crank the engine.
11 Shroud 27 Oil Pump Adjusting Screw
Covers the engine. Serves to adjust chain oil feed rate.
12 Shroud Lock 28 Stop
Secures shroud to chainsaw Limits travel of oil pump adjusting screw.
13 Decompression Valve 29 Oil Tank Cap
Eases engine starts. Closes the oil tank.
14 Spark Plug 30 Handlebar
Ignites fuel-air mixture in the engine. For holding, controlling and carrying the chainsaw.

4 0458-809-0121-A
4 Safety Precautions English

31 Chain Scabbard Rotate in this direction to increase chain tension.

Helps protect user from contact with saw chain.
This symbol marks the handle heating switch.
# Serial Number

This symbol marks the decompression valve.

3.2 Features
The chainsaw may be equipped with the following features:

This symbol marks the stop switch.

Guaranteed sound power level according to

LWA directive 2000/14/EC in dB(A) in order to make
sound emissions of products comparable.

0000-GXX-5817-A0
4 Safety Precautions

4.1 Warning Signs

1 Handle heating switch Meanings of warning signs on the chainsaw:
Switches the handle heating on and off. Heats the front
Observe safety notices and take the necessary
and rear handles.
precautions.

3.3 Symbols
Meanings of symbols that may be on the chainsaw: Read, understand and save the instruction
manual.
This symbol marks the fuel tank.

This symbol marks the chain oil tank. Wear safety glasses, hearing protection and a
hard hat.

The chain brake is engaged or disengaged in

this direction. Observe safety notices on kickback and take the
necessary precautions.
This symbol shows the direction of rotation of the
chain.
This symbol marks the oil pump adjusting screw
and the chain oil feed rate.

0458-809-0121-A 5
English 4 Safety Precautions

4.2 Intended Use restricted, he or she may work only under the
The STIHL MS 500i is designed for cutting wood, limbing supervision of or as instructed by a responsible
and felling trees. person.
– The user can identify and assess the dangers of the
WARNING chainsaw.
￭ Using the chainsaw for purposes for which it is not – The user must be of legal age or is being trained in a
designed may result in serious or fatal injuries and trade under supervision in accordance with national
damage to property. rules and regulations.
► Use the chainsaw as described in this instruction – The user has received instruction from a STIHL
manual. servicing dealer or other experienced user before
working with the chainsaw for the first time.
4.3 The Operator – The user must not be under the influence of alcohol,

WARNING medication or drugs.

￭ Users without adequate training or instruction cannot ► If the user is working with a chainsaw for the first time:
recognize or assess the risks involved in using the Practice cutting logs on a sawhorse or other support.
chainsaw. The user or other persons may sustain serious
or fatal injuries. ► If you have any queries: Contact your STIHL servicing
dealer for assistance.
► Read, understand and save the instruction
manual. ￭ The chainsaw’s ignition system produces an
electromagnetic field. This field may interfere with some
pacemakers. This can result in serious or fatal injuries.
► If the user has a pacemaker: Make sure the pacemaker
► If the chainsaw is passed on to another person: Always is not affected.
give them the instruction manual.
► Make sure the user meets the following requirements:
4.4 Clothing and Equipment
– The user must be rested.
– The user must be in good physical condition and
WARNING
mental health to operate and work with the chainsaw. ￭ Long hair can become entangled in the saw during
If the user’s physical, sensory or mental ability is operation. This can result in serious injuries.
► Tie up and confine long hair so that it cannot be
entangled in the saw.
￭ Objects can be thrown through the air at high speed
during operation. This can result in personal injury.
► Wear close-fitting safety glasses. Suitable
safety glasses that have been tested and
labeled in accordance with EN 166 or
national standards are available from
retailers.
► STIHL recommends that you wear a face shield.

6 0458-809-0121-A
4 Safety Precautions English

► Wear a long-sleeved, snug-fitting upper garment. 4.5 Work Area and Surroundings
￭ Noise occurs during operation. Noise can harm your
hearing.
WARNING
￭ Bystanders, children and animals are not aware of the
► Wear hearing protection.
dangers of the chainsaw or thrown objects. Innocent
bystanders, children and animals may be seriously injured
and damage to property may occur.
► Keep bystanders, children and animals away from the
￭ Falling objects can cause head injuries. work area.
► If there is a danger of falling objects during ► Do not leave the chainsaw unattended.
operation: Wear a safety hard hat.
► Make sure that children cannot play with the chainsaw.
￭ Hot exhaust gas is emitted through the muffler while the
engine is running. Hot exhaust gas can ignite easily
￭ Dust can be whipped up during operation: Whipped up flammable materials and cause a fire.
dust can damage the respiratory passages and cause
► Keep exhaust gas well away from easily flammable
allergic reactions.
materials.
► If dust is whipped up and forms a cloud: Wear a dust
respirator mask.
￭ Inappropriate clothing can snag on wood, brush or the
4.6 Safe Condition
saw. Not wearing personal protective equipment may 4.6.1 Chainsaw
result in serious injury.
The chainsaw is in a safe condition if the following points are
► Wear snug-fitting clothing. observed:
► Do not wear a scarf or jewelry. – The saw is not damaged.
￭ The user can come into contact with the rotating saw – There is no fuel leaking from the chainsaw.
chain during operation. This can result in serious injuries.
– The fuel tank and oil tank caps are closed.
► Wear long trousers with cut-retardant inserts.
– The saw is clean.
￭ The user can be cut by the wood during operation. The
user can come into contact with the saw chain during – Chain catcher is fitted and undamaged.
cleaning and maintenance work. This can result in – Chain brake is operating properly.
personal injury.
► Wear work gloves made of durable material. – The controls function properly and have not been
modified.
￭ Wearing unsuitable footwear may cause you to slip or
– Chain lubrication is operating properly.
stumble. Contact with the rotating saw chain can result in
cuts. This can result in personal injury. – Wear marks on chain sprocket are not deeper than 0.5
► Wear chainsaw boots with cut retardant inserts. mm.
– A combination of guide bar and saw chain recommended
in this instruction manual is mounted.
– The guide bar and chain are properly mounted.

0458-809-0121-A 7
English 4 Safety Precautions

– The chain is properly tensioned. – Guide bar is not deformed.

– Only original STIHL accessories designed for this saw are – The minimum groove depth is maintained, @ 19.3.
fitted.
– Bar rails are free from burrs.
– Accessories are properly mounted.
– Bar groove is not pinched or splayed.

WARNING WARNING
￭ If components do not comply with safety requirements,
￭ If the guide bar is not in a safe condition, it can no longer
they will no longer function properly, safety devices may
support and guide the saw chain properly. The rotating
be rendered inoperative and fuel leaks may occur. This
saw chain can jump off the guide bar. This can result in
can result in serious or fatal injuries.
serious or fatal injuries.
► Work only with an undamaged chainsaw.
► Work only with an undamaged guide bar.
► If fuel is leaking from the chainsaw: Do not use the
► If the groove depth is less than the minimum depth:
chainsaw and contact a STIHL dealer for assistance.
Mount a new guide bar.
► Close the fuel tank and oil tank caps.
► Deburr the guide bar every week.
► If the saw is dirty: Clean the saw.
► If you have any queries: Contact your STIHL servicing
► Work only with property fitted and undamaged chain dealer.
catcher.
► Never modify your chainsaw. Exception: Mounting a 4.6.3 Saw Chain
combination of guide bar and saw chain recommended The saw chain is in a safe condition if the following points
in this instruction manual. are observed:
► If the controls do not function properly: Do not use your – Chain is not damaged.
saw.
– Chain is properly sharpened.
► Only fit original STIHL accessories designed for this
saw model. – The service marks on the cutters are still visible.

► Mount the guide bar and chain as described in this

instruction manual. WARNING
► Mount accessories as described in this instruction ￭ If components do not comply with safety requirements,
manual or the instructions supplied with the accessory. they will no longer function properly and safety devices
may be rendered inoperative. This can result in serious or
► Never insert objects in the saw’s openings.
fatal injuries.
► If you have any queries: Contact your STIHL servicing ► Work only with an undamaged saw chain.
dealer for assistance.
► Sharpen the chain properly.
4.6.2 Guide Bar ► If you have any queries: Contact your STIHL servicing
dealer for assistance.
The guide bar is in a safe condition if the following points are
observed:
– Guide bar is not damaged.

8 0458-809-0121-A
4 Safety Precautions English

4.7 Fuel Mixture and Refueling ￭ Clothing that has been in contact with fuel or gasoline is
more easily flammable. This can result in serious or fatal
WARNING injuries and damage to property.
￭ This chainsaw requires a fuel mixture of gasoline and two- ► If your clothing comes into contact with fuel or gasoline:
stroke engine oil. Fuel mixture and gasoline are extremely Change your clothing.
flammable. If fuel mixture or gasoline make contact with
￭ Fuel, gasoline and two-stroke engine oil can harm the
open fire or hot objects, they can cause a fire or
environment.
explosions. This can result in serious or fatal injuries and
damage to property. ► Do not spill fuel, gasoline or two-stroke engine oil.
► Protect fuel mixture and gasoline from heat and fire. ► Fuel, gasoline and two-stroke engine oil can harm the
environment.
► Do not spill fuel mixture and gasoline.
￭ Fuel, gasoline or two-stroke engine oil can cause irritation
► Do not smoke.
if they come into direct contact with the skin or eyes.
► Never refuel near a fire. ► Avoid contact with fuel, gasoline and two-stroke engine
► Shut off the engine and allow it to cool down before oil.
refueling. ► In case of contact with the skin: Wash affected areas
► Start the engine at least 3 meters from the fueling spot, with plenty of water and soap.
outdoors only. ► In case of contact with the eyes: Rinse eyes with plenty
￭ Inhaling fuel fumes and gasoline fumes can have toxic of water for at least 15 minutes and seek medical
effects. advice.
► Avoid inhaling fuel fumes or gasoline fumes. ￭ The saw’s ignition system produces sparks. Unconfined
► Refuel in a well-ventilated location. sparks may cause a fire or an explosion in an easily
combustible or explosive environment. This can result in
￭ The chainsaw becomes hot during operation, or in a very serious or fatal injuries and damage to property.
hot environment. Depending on the type of fuel, altitude, ► Use the spark plugs described in this instruction
ambient temperature and the temperature of the saw, the manual.
fuel expands and can cause a pressure build-up in the
tank. Fuel may escape as a spray and ignite when the fuel ► Insert and tighten down the spark plug.
tank cap is opened. This can result in serious injuries and ► Connect the spark plug boot and press it down firmly.
damage to property.
￭ The saw can be damaged if it is run on a fuel mixture
► Allow the saw to cool down before opening the tank cap.
consisting of unsuitable gasoline or an unsuitable two-
► Open the tank cap slowly in stages. stroke engine oil or if an incorrect mix ratio of gasoline and
two-stroke engine oil is used.
► Mix the fuel as described in this instruction manual.
￭ The mixture of gasoline and two-stroke engine oil can
separate if it is stored for a long period. The saw can be
damaged if it is used with a fuel mix that has separated.
► Before refueling the saw: Thoroughly mix the fuel.
► Use a mixture of gasoline and two-stroke engine oil that
is not older than 30 days (STIHL MotoMix: 2 years).

0458-809-0121-A 9
English 4 Safety Precautions

4.8 Working ￭ The user’s ability to hear and assess noises is restricted
when wearing hearing protection with the engine running.
4.8.1 Cutting ► Work calmly and carefully.

WARNING ￭ Do not accelerate the engine with the chain brake

engaged since this can damage the chain brake.
￭ Always work within calling distance of others in case help
is needed. ► Disengage the chain brake before you start cutting.
► Make sure than persons outside the work area are ￭ The rotating saw chain can cut the operator. This can
within calling distance. result in serious injuries.
￭ If the engine is not started properly, the user may lose ► Do not touch the rotating saw chain.
control of the chainsaw. This can result in serious injuries. ► If the saw chain is blocked by an object: Shut off the
► Start the engine as described in this instruction manual. engine and engage the chain brake. Then remove the
► If the saw chain is touching the ground or objects: Do object causing the blockage.
not start the engine. ￭ The rotating chain becomes hot and expands. If the chain
is not lubricated sufficiently and re-tensioned at regular
￭ The user cannot concentrate on the work in certain
situations. The user can lose control of the saw, stumble intervals, it man come off the guide bar or break. This can
or fall and be seriously injured. result in serious injuries and damage to property.
► Work calmly and carefully. ► Use special chain oil.

► If light and visibility are poor: Do not use your saw. ► Check chain tension regularly during cutting work. If
chain tension is insufficient: Tension the chain.
► Operate the chainsaw alone.
￭ If the behavior of the saw changes during operation or
► Do not work above shoulder height. feels unusual, it may no longer be in a safe condition. This
► Watch out for obstacles. can result in serious injuries and damage to property.
► Stop work and contact your STIHL dealer for
► Stand on the ground while working and keep a good
assistance.
balance. If it is necessary to work at heights: Use a lift
bucket or a safe platform. ￭ Saw vibrations may occur during operation.
► If you begin to feel tired: Take a break. ► Wear gloves.

￭ Exhaust gas is produced when the engine is running. ► Take regular breaks.
Breathing in exhaust gas can have toxic effects. ► If signs of circulation problems occur: Seek medical
► Avoid inhaling exhaust gas. advice.
► Operate the chainsaw is a well ventilated location.
► In the event of nausea, headache, visual disturbances,
problems with hearing or dizziness: Stop work and seek
medical advice.

10 0458-809-0121-A
4 Safety Precautions English

￭ Sparks may occur if the rotating chain makes contact with ￭ A branch may fall to the ground during limbing. The user
a hard object. Sparks may cause a fire in an easily may trip, fall or be seriously injured.
combustible location. This can result in serious or fatal ► Limb from the base to the crown of the tree.
injuries and damage to property.
► Do not work in an easily combustible location. 4.8.3 Felling
￭ Note that the saw chain continues to rotate for a short
period after you release the trigger. The rotating saw chain WARNING
can cut the user. This can result in serious injuries. ￭ Inexperienced users cannot assess the dangers of felling
► Wait for the chain to come to a standstill. a tree. This can result in serious or fatal injuries and
damage to property.
► If you have any queries: Do not fell the tree yourself.
￭ A tree and branches can fall on bystanders or objects
during the felling operation. This can result in serious or
fatal injuries and damage to property.
1 2 ► Determine direction of fall so that the area in which the
tree falls is clear.
2 1 ► Do not allow bystanders, children or animals within 2.5

0000-GXX-1245-A0
tree lengths of the felling site.
► Remove broken or dead branches from the tree crown
before felling.
► If broken or dead branches cannot be removed from the
WARNING crown: Do not fell the tree.
￭ The guide bar can be pinched when cutting wood that is ► Observe tree crown and crowns of neighboring trees
under tension. The user can lose control of the saw and and keep clear of falling branches.
be seriously injured.
￭ When the tree falls the trunk can break or spring back in
► Make a relieving cut in the compression side (1) first,
the direction of the user. This can result in serious or fatal
then perform bucking cut at the tension side (2).
injuries.
► Plan an escape path sideways behind the tree.
4.8.2 Limbing
► Walk backwards along the escape path and observe the
WARNING falling tree.
￭ If the underside of the felled tree is limbed first, it will no ► Do not walk backwards down slopes.
longer be supported on the ground by branches. The tree
can move during cutting work. This can result in serious or
fatal injuries.
► Cut through large limbs on the underside of the tree only
after it has been bucked.
► Do not stand on the log while limbing it.

0458-809-0121-A 11
English 4 Safety Precautions

￭ Obstacles in the work area and on the escape path can 4.9 Reactive Forces
hinder the user. The user may trip and fall. This can result
in serious or fatal injuries. 4.9.1 Kickback
► Remove all obstacles from the work area and escape
path.
￭ If you cut into or through the hinge, stabilizing strap or
holding strap too soon, the intended direction of fall
cannot be controlled or the tree can fall prematurely. This
can result in serious or fatal injuries and damage to
property.
► Do not cut into or through the hinge.

0000-GXX-2732-A0
► Cut through the stabilizing strap or holding strap last.
► If the tree begins to fall too soon: Abandon the felling cut
and retreat along the escape.
Kickback can be caused for the following reasons:
￭ Kickback can occur if the rotating chain in the upper
quadrant of the bar nose makes contact with a hard felling – The rotating saw chain in the upper quadrant of the bar
wedge and is suddenly braked. This can result in serious nose makes contact with a hard object and is suddenly
or fatal injuries. braked.
► Use aluminum or plastic felling wedges. – The rotating saw chain is pinched at the bar nose.
￭ If the tree does not fall all the way to the ground or gets
caught on another tree, the operator cannot finish the The chain brake cannot prevent kickback.

WARNING
operation in a controlled manner.
► Stop the felling operation and use a cable winch or
suitable vehicle to pull the tree to the ground.
￭

0000-GXX-4119-A0
12 0458-809-0121-A
4 Safety Precautions English

￭ If kickback occurs, the saw can be thrown up in the ► Keep the guide bar straight in the cut.
direction of the operator. The operator can lose control of
► Apply the spiked bumper properly.
the saw and be seriously or fatally injured.
► Hold the saw firmly with both hands. ► Always cut with the chain running at full speed.
► Always keep your body out of the plane of the cutting 4.9.3 Pushback
attachment.
► Use the working techniques described in this instruction
manual.
► Do not cut with the upper quadrant of the bar nose.
► Always cut with a properly sharpened and tensioned
saw chain.
► Use a reduced kickback saw chain.

0000-GXX-1349-A0
► Use a guide bar with a narrow radius nose.
► Always cut with the chain running at full speed.

4.9.2 Pull-in
The saw is pushed back toward the operator when the top of
the bar is used for cutting.

WARNING
￭ If the rotating chain makes contact with a hard object and
is suddenly pinched, the saw can be abruptly pushed back
toward the operator. The operator can lose control of the
saw and be seriously or fatally injured.
► Hold the saw firmly with both hands.
0000-GXX-1348-A0

► Operate the saw as described in this instruction manual.

► Keep the guide bar straight in the cut.
► Always cut with the chain running at full speed.
The saw is pulled away from the operator when the bottom
of the bar is used for cutting.
4.10 Transporting
WARNING
￭ If the rotating chain makes contact with a hard object and WARNING
is suddenly pinched, the saw is abruptly jerked away from ￭ The saw may turn over or shift during transport. This can
the operator. The operator can lose control of the saw and result in serious injuries and damage to property.
be seriously or fatally injured. ► Shut off the engine.
► Hold the saw firmly with both hands.
► Engage the chain brake.
► Operate the saw as described in this instruction manual.

0458-809-0121-A 13
English 4 Safety Precautions

► Fit the scabbard so that it completely covers the guide 4.12 Cleaning, Maintenance and Repairs
bar.
► Secure the chainsaw with lashing straps or a net to WARNING
prevent it turning over and moving. ￭ The cutting attachment can start rotating unintentionally if
￭ the engine is running during cleaning, maintenance or
repair operations. This can result in serious injuries and
damage to property.
► Shut off the engine.
► Engage the chain brake.
￭ The muffler and engine may be hot after a period of
operation. This can result in burn injuries.
► Wait until the muffler and engine cool down.

0000-GXX-2733-A0
￭ Aggressive cleaning agents, a water jet or pointed objects
can damage the saw, guide bar and saw chain. If the saw,
guide bar or saw chain are not cleaned correctly,
￭ The muffler and engine may be hot after a period of components may no longer function properly or safety
operation. There is a risk of burn injuries. devices may be rendered inoperative. This can result in
serious injuries.
► Carry the saw by holding the front handle in your right
hand with the guide bar pointing to the rear. ► Clean the saw, guide bar and saw chain as described in
this instruction manual.
￭ If the saw is not maintained as described in this instruction
4.11 Storing manual, components may no longer function properly or
WARNING safety devices may be rendered inoperative. This can
result in serious or fatal injuries.
￭ Children are not aware of and cannot assess the dangers ► Service or repair the saw as described in this instruction
of a chainsaw and can be seriously injured. manual.
► Shut off the engine.
￭ If the guide bar and chain are not maintained or repaired
► Engage the chain brake. as described in this instruction manual, components may
► Fit the scabbard so that it completely covers the guide no longer function properly or safety devices may be
bar. rendered inoperative. This can result in serious injuries.
► Service or repair the guide bar and chain as described
► Store the saw out of the reach of children.
in this instruction manual.
￭ Dampness can corrode the electrical contacts on the saw
￭ The user can be cut by the sharp cutters while cleaning or
and metal components. This can damage the saw.
servicing the saw chain. This can result in personal injury.
► Store the saw in a clean and dry condition.
► Wear work gloves made of durable material.

14 0458-809-0121-A
5 Preparing the Saw for Operation English

5 Preparing the Saw for Operation 3

5.1 Preparing the Saw for Operation

2
Perform the following steps before starting work:
► Make sure the following components are in a safe

0000-GXX-2734-A0
condition:
– Chainsaw, @ 4.6.1. 4
– Guide bar, @ 4.6.2. 1
– Saw chain, @ 4.6.3. ► Rotate the nuts (1) counterclockwise until the chain
► Clean the saw, @ 15.1. sprocket cover (2) can be removed.
► Mount the bar and chain, @ 6.1.1. ► Remove the chain sprocket cover (2).
► Tension the saw chain, @ 6.2. ► Turn the tensioning screw (3) counterclockwise until the
► Fill up with chain oil, @ 6.3. tensioner slide (4) butts against the left end of the
housing.
► Check the chain brake, @ 10.4.
► Refuel the saw, @ 8.2.
► Check the controls, @ 10.5.
► Check chain lubrication, @ 10.6.
► If you cannot carry out these steps: Do not use your
chainsaw and contact your STIHL servicing dealer for
assistance.

0000-GXX-2954-A0
6 Assembling the Saw

6.1 Mounting and Removing the Bar and Chain ► Fit the chain in the bar groove so that the arrows on the tie
straps on the top of the bar point in the direction of
6.1.1 Mounting the Bar and Chain rotation.
The bar and chain combinations that can be used with the
chain sprocket are listed in the specifications, @ 20.1.
► Shut off the engine and engage the chain brake.

0458-809-0121-A 15
English 6 Assembling the Saw

6.1.2 Removing the Bar and Chain

► Shut off the engine and engage the chain brake.
► Rotate the nuts counterclockwise until the chain sprocket
cover can be removed.
7 ► Remove the sprocket cover.
► Turn the tensioning screw counterclockwise as far as
stop.

0000-GXX-2735-A0
The chain is now slack.
► Remove the bar and chain.

► Fit the guide bar and chain on the saw and check the 6.2 Tensioning the Saw Chain
following points: The saw chain expands or contracts during cutting work.
– Chain drive links are seated in teeth of chain sprocket Chain tension changes as a result. Check chain tension
(7). regularly during operation and readjust if necessary.
– Collar studs (5) are located in slot in tail of guide bar (6). ► Shut off the engine and engage the chain brake.
– Peg of tensioner slide (4) engages hole (8) in guide bar
(6).
The guide bar (6) may be either way round. The logo on the
guide bar (6) may also be upside down.
► Disengage the chain brake.

0000-GXX-2929-A1
1 1
a

► Loosen the nuts (1).

0000-GXX-2928-A0

► Disengage the chain brake.

► Hold the bar nose up and turn the tensioning screw (2)
clockwise until the following points apply:
– Chain sag ‘a’ in the center of the bar is 1 - 2 mm.
► Turn the tensioning screw (3) clockwise until the chain fits – The chain can still be pulled easily along the bar with
snugly against the bar. Make sure the drive link tangs two fingers.
engage the bar groove.
► Keep holding the bar nose up and tighten down the nuts
The guide bar (6) and chain are seated against the saw.
(1) firmly.
► Fit the sprocket cover (2) so that it is flush with the saw.
► If chain sag ‘a’ in the center of the bar is not 1 - 2 mm:
► Fit and tighten down the nuts (1) firmly. Readjust chain tension.

16 0458-809-0121-A
6 Assembling the Saw English

6.3 Filling Up with Chain Oil ► Press the cap down and rotate it clockwise as far as stop.
Chain oil lubricates and cools the rotating chain. The cap snaps into place. The mark (1) points to mark (3),
► Check to see if the oil tank cap can be pulled upwards and
► Shut off the engine and engage the chain brake.
off.
► Place your saw on a level surface so that the oil tank cap
► If the oil tank cap cannot be pulled upwards and off: Fold
faces up.
down the grip on the oil tank cap.
► Use a damp cloth to clean the tank cap and the area The oil tank is closed.
around it.
If the oil tank cap can be pulled upwards and off, perform the
following steps:
► Place the oil tank cap in the filler opening – in any position.

0000-GXX-2930-A0

0000-GXX-3135-A0
► Swing the grip on the oil tank cap to the vertical position.
► Turn the oil tank cap counterclockwise as far as stop.
2
► Remove the oil tank cap.
► Press the cap down and rotate it clockwise as far as stop.
► Fill up with chain oil, taking care not to spill any oil and do
not overfill the tank. ► Press the cap down and rotate it counterclockwise until
mark (1) points to mark (2).
► If the grip on the oil tank cap has dropped into the closed
position: Raise the grip until it is vertical. ► Now try again to close the oil tank.
► If the oil tank still cannot be closed properly: Do not use
the chainsaw and contact a STIHL dealer for assistance.
1 The chainsaw is not in a safe condition.

1
0000-GXX-2931-A0

3
2
► Place the cap in the filler opening so that mark (1) lines up
with mark (2).

0458-809-0121-A 17
English 7 Engaging and Disengaging the Chain Brake

6.4 Mounting the Spiked Bumper ► Push the hand guard away from the front handle with your
left hand.
The hand guard engages with an audible click. The chain
brake is engaged.
4
7.2 Disengaging the Chain Brake

0000-GXX-3823-A0
2
1
► Place the spiked bumper (1) in position.

0000-GXX-2933-A0
► Fit the screw (2).
► Insert screw (3) through spiked bumper and nut (4).
► Tighten down the screws (2) and (3) firmly.
The spiked bumper (1) must not be removed.
► Pull the hand guard toward the front handle with your left
hand.
The hand guard engages with an audible click. The chain
7 Engaging and Disengaging the Chain brake is disengaged.
Brake
7.1 Engaging the Chain Brake 8 Mixing Fuel and Refueling the
The saw is equipped with a chain brake. Chainsaw
The chain brake is activated by the inertia of the front hand
guard if the kickback force is high enough or can be engaged 8.1 Mixing Fuel
by the operator. This chainsaw requires a fuel mixture of gasoline and two-
stroke engine oil in a ratio of 50:1.
STIHL recommends you use STIHL MotoMix.
If you mix the fuel yourself, use only STIHL two-stroke
engine oil or another high-performance engine oil in
accordance with JASO FB, JASO FC, JASO FD, ISO-L-
EGB, ISO-L-EGC or ISO-L-EGD.
STIHL specifies STIHL HP Ultra two-stroke engine oil or an
0000-GXX-2932-A0

equivalent high-performance engine oil in order to maintain

emission limits over the machine’s service life.

18 0458-809-0121-A
8 Mixing Fuel and Refueling the Chainsaw English

► Make sure that the octane number of the gasoline is at

least 90 RON and the ethanol content is not more than WARNING
10%.
The chainsaw becomes hot during operation, or in a very hot
► Make sure the two-stroke engine oil you are using meets environment. Depending on the type of fuel, altitude,
the requirements. ambient temperature and the temperature of the saw, the
► Depending on the required amount of fuel, determine the fuel expands and can cause a pressure build-up in the tank.
correct amounts of two-stroke engine oil and gasoline in a Fuel may escape as a spray and ignite when the fuel tank
mix ratio of 50:1. Examples for fuel mixes: cap is opened. This can result in serious injuries and
– 1 liter gasoline, 20 ml two-stroke engine oil damage to property.
– 3 liters gasoline, 60 ml two-stroke engine oil ► Allow the saw to cool down before opening the tank cap.
► Open the tank cap slowly in stages.
– 5 liters gasoline, 100 ml two-stroke engine oil
► Pour two-stroke engine oil into a clean approved fuel ► Turn the fuel tank cap about 1/8 of a turn
canister first and then add gasoline. counterclockwise.
► Thoroughly mix the fuel. If the fuel tank is under pressure, you will hear pressure
being released.
► When the tank is no longer under pressure: Turn the tank
8.2 Fueling the Saw cap counterclockwise until the marks on the cap and fuel
► Shut off the engine and engage the chain brake. tank are in alignment.
► Allow chainsaw to cool down. ► Remove the fuel tank cap.
► Place your chainsaw on a level surface so that the fuel
tank cap faces up. NOTICE
► Use a damp cloth to clean the tank cap and the area Bright light, sunlight and extreme temperatures can cause
around it. the fuel mix to separate much faster. The saw can be
► Swing the grip on the fuel tank cap to the vertical position. damaged if it is used with a fuel mix that has become
separated.
► Thoroughly mix the fuel.
► Do not use fuel mix that has been stored for more than 30
days.

► Fill the tank to within no more than 15 mm of the brim,

taking care not to spill any fuel.
► If the grip on the fuel tank cap has dropped into the closed
0000-GXX-2934-A1

position: Raise the grip until it is vertical.

0458-809-0121-A 19
English 9 Starting and Stopping the Engine

► Now try again to close the fuel tank.

1 ► If the fuel tank still cannot be closed properly: Do not use
4 the chainsaw and contact a STIHL dealer for assistance.
The chainsaw is not in a safe condition.
1

9 Starting and Stopping the Engine

0000-GXX-2935-A1
9.1 Starting the Engine
2 3
► Place the cap in the filler opening so that mark (1) lines up
with mark (2). 2
► Press the cap down and rotate it clockwise as far as stop. 1
The cap snaps into place. The mark (1) is in line with mark
(4) and points to mark (3).

0000-GXX-6458-A0
► Check to see if the fuel tank cap can be pulled upwards
and off.
► If the fuel tank cap cannot be pulled upwards and off: Fold
the grip flush with the top of the cap.
3
The fuel tank is closed.
► Engage the chain brake (2).
If the fuel tank cap can be pulled upwards and off, perform
► Pull off the chain guard (scabbard).
the following steps:
► Depress the decompression valve (1).
► Place the fuel tank cap in the filler opening – in any
position. ► Press the manual fuel pump bulb (3) at least eight times.

A B C

0000-GXX-2936-A0
0000-GXX-3136-A1

2
► Press the cap down and rotate it clockwise as far as stop. ► Hold the chainsaw firmly in one of three ways:
► Press the cap down and rotate it counterclockwise until
mark (1) points to mark (2).

20 0458-809-0121-A
10 Checking the Saw English

– Place the saw on level ground. Hold the saw firmly on 9.2 Stopping the Engine
the ground with your left hand on the handlebar – your
thumb should be under the handle. Put the toe of your
right boot into the rear handle and press down. 1
– Place the saw on level ground. Hold the saw firmly on
the ground with your left hand on the handlebar – your
thumb should be under the handle. Put the heel of your
right boot into the rear handle and press down.

0000-GXX-9935-A0
– Hold the saw firmly with your left hand on the handlebar
– your thumb should be under the handle. Hold the rear
handle tightly between your legs, just above the knees. 2

► Release the throttle trigger (2).

The engine runs at idling speed.
► Depress the stop switch (1).
The engine stops and the stop switch (1) springs back to
the off position.
► If the engine does not stop: Do not use the chainsaw and

0000-GXX-2937-A0
contact your STIHL servicing dealer for assistance.
The saw has a malfunction.

► Pull the starter grip slowly with your right hand until you 10 Checking the Saw
feel it engage.
► Pull the starter grip quickly and allow the starter rope to
rewind several times until the engine runs. 10.1 Checking the Chain Sprocket
The engine runs at idling speed. ► Shut off the engine.
► Disengage the chain brake.
NOTICE
► Remove the chain sprocket cover.
Do not accelerate the engine with the chain brake engaged
► Remove the bar and chain.
since this can damage the chain brake.
► Disengage the chain brake before you start cutting.

► Disengage the chain brake.

Your saw is ready for operation.

If the saw chain rotates while the engine is idling:

► Shut off the engine and engage the chain brake.
► Do not use your chainsaw and contact your STIHL
servicing dealer for assistance.
The saw has a malfunction.

0458-809-0121-A 21
English 10 Checking the Saw

– Bar groove is pinched or splayed.

► If you have any queries: Contact your STIHL servicing
dealer for assistance.

10.3 Checking the Saw Chain

► Shut off the engine and engage the chain brake.

0000-GXX-3162-A0
a 1
2
► Use a STIHL gauge to check the wear marks on the
sprocket.
► If wear marks are deeper than a = 0.5 mm: Do not use your

0000-GXX-1218-A0
chainsaw and contact your STIHL servicing dealer for
assistance.
The chain sprocket must be replaced.

► Use a STIHL filing gauge (2) to check the height of the

10.2 Checking the Guide Bar depth gauges (1). The STIHL filing gauge must match the
► Shut off the engine and engage the chain brake. chain pitch.
► Remove the chain and guide bar. ► If a depth gauge (1) projects from the filing gauge (2):
Lower the depth gauge (1), @ 16.3.

2 3
0000-GXX-1217-A0

0000-GXX-1372-A0
4
► Measure depth of bar groove with scale on STIHL filing
gauge. ► Make sure the service marks (1 to 4) on the cutters are
► Install a new guide bar if one of the following points visible.
applies: ► If one of the service marks is not visible on a cutter: Do not
– Guide bar is damaged. use your chainsaw and contact your STIHL servicing
– Measured bar groove depth is less than specified dealer for assistance.
minimum depth, @ 19.3.

22 0458-809-0121-A
11 Operating the Saw English

► Use a STIHL filing gauge to check that a filing angle of 30° Stopping the Engine
has been maintained on all cutters. The STIHL filing
► Start the engine.
gauge must match the chain pitch.
► Depress the stop switch.
► If a filing angle of 30° has not been maintained:
The engine stops and the stop switch springs back to the
Resharpen the saw chain.
off position.
► If you have any queries: Contact your STIHL servicing
► If the engine does not stop: Do not use your chainsaw and
dealer for assistance.
contact your STIHL servicing dealer for assistance.
The saw has a malfunction.
10.4 Testing the Chain Brake
► Shut off the engine and engage the chain brake. 10.6 Checking Chain Lubrication
► Start the engine and disengage the chain brake.
WARNING ► Hold the guide bar over a light surface.
The chain's cutters are very sharp. There is a risk of cut
► Open the throttle.
injuries.
Chain oil is thrown off the chain and is visible on the light
► Wear work gloves made of durable material. surface. Chain lubrication is operating properly.
► Try to pull the chain along the guide bar by hand. If no chain oil can be seen:
If the chain cannot be pulled along the bar by hand, the
chain brake is functioning. ► Shut off the engine.
► If the chain can be pulled along the bar by hand: Do not ► Fill up with chain oil.
use your chainsaw and contact your STIHL servicing ► Check chain lubrication again.
dealer for assistance. ► If chain oil is still not visible on the light surface: Do not
The chain brake is defective. use your chainsaw and contact your STIHL servicing
dealer for assistance. Chain lubrication is defective.
10.5 Checking the Controls
Throttle trigger lockout and throttle trigger
11 Operating the Saw
► Shut off the engine and engage the chain brake.
► Attempt to pull the trigger without depressing the lockout 11.1 Adjusting Oil Feed Rate
lever. The chainsaw has an adjustable oil pump.
► If the trigger can be pulled: Do not use your chainsaw and
contact your STIHL servicing dealer for assistance.
There is a malfunction in the throttle trigger lockout.
► Press down the throttle trigger lockout and hold it there.
► Pull the throttle trigger and release it again.
► If the throttle trigger is stiff or does not spring back to its
idle position: Do not use your chainsaw and contact your
STIHL servicing dealer for assistance.
The throttle trigger is defective.

0458-809-0121-A 23
English 11 Operating the Saw

11.2 Holding and Controlling the Chainsaw

A

0000-GXX-3165-A0

0000-GXX-2948-A0
2 1
The oil feed rate is suitable for most applications when the
oil pump adjusting screw (1) is in position E (Ematic).
► Hold and control your saw with your left hand on the front
The oil pump feed rate can be adjusted to suit different bar handle and your right hand on the control handle. Wrap
lengths, wood species and working techniques. The range of thumb of left hand around the front handle and thumb of
adjustment of the oil pump adjusting screw (1) is limited by right handle around the control handle.
a stop (2). The stop (2) can be depressed in order to further
increase the oil feed rate.
11.3 Sawing
To increase oil feed rate
► Turn the oil pump adjusting screw (1) clockwise. WARNING
If kickback occurs, the saw can be thrown up in the direction
To increase oil feed rate still further of the operator. This can result in serious or fatal injuries.
► Use a suitable tool to depress the stop (2). ► Always cut with the chain running at full speed.
The stop (2) remains permanently depressed. ► Do not cut with the upper quadrant of the bar nose.

► Begin the cut with the chain running at full speed and keep
NOTICE the guide bar vertical.
The oil tank will be drained at a faster rate if the oil pump
adjusting screw (1) is in the ‘A’ segment. The point where the
saw chain is no longer being lubricated properly will be
reached sooner.
► Fill the oil tank to maximum.
► Move the oil pump adjusting screw away from the ‘A’
segment when the increased oil flow rate is no longer
required.

0000-GXX-2949-A0
► Turn the oil pump adjusting screw (1) clockwise.

To reduce oil feed rate

► Turn the oil pump adjusting screw (1) counterclockwise.
► Engage the bumper spike and use it as a fulcrum.

24 0458-809-0121-A
11 Operating the Saw English

► Guide the full width of the bar into the wood and reposition 11.5 Felling
the bumper spike as required.
► Take the weight of the saw at the end of the cut. 11.5.1 Determining direction of fall and escape path
► Determine direction of fall so that the area in which the
tree falls is clear.
11.4 Limbing

0000-GXX-1246-A0
0000-GXX-2950-A0

B
B
► Observe the following points when planning escape path
► Support the saw on the log. (B):
► With the chain running a full speed, pivot the bar upwards – Escape path (B) at an angle of 45° to direction of fall (A).
against the limb. – No obstacles on the escape path (B).
► Cut through the limb with the top of the bar. – The top of the tree can be observed.
– If the escape path (B) is on a slope, it must be parallel
to the slope.

11.5.2 Preparing work area at base of tree

1 2 ► Remove obstacles from work area at tree base.
► Remove growth from tree base.
2 1
0000-GXX-1245-A0

► If the limb is under tension: Make the relieving cut (1) at

the compression side and then perform bucking cut (2)
from the tension side.

0000-GXX-1247-A0
0458-809-0121-A 25
English 11 Operating the Saw

► If the tree has large, healthy buttress roots: Make vertical

cut first and then a horizontal cut, and remove the
resulting piece.

11.5.3 Basic information on felling cut

0000-GXX-1249-A0
C E
C 1/10 ► Position the saw so that the felling notch is an right angles

0000-GXX-1251-A1
Ø G to the direction of fall and the saw is close to the ground.
► Make the horizontal cut.
► Make the angle cut at 45° to the horizontal cut.

C Felling notch
The felling notch determines the direction of fall.
D Hinge
The hinge helps control the falling tree. The width of the
hinge is 1/10 of the trunk diameter.
E Felling cut

0000-GXX-1250-A1
The tree is felled with the felling cut. The felling cut is
1/10 of the trunk diameter (at least 3 cm) above the
bottom of the felling notch.
F Stabilizing strap
► If the wood is sound and long-fibered: Observe the
The stabilizing strap supports the tree and helps prevent
following points when making sapwood cuts:
it from falling prematurely. The width of the stabilizing
strap is 1/10 to 1/5 of the trunk diameter. – The cuts must be the same at both sides.
– The cuts must be at same height as bottom of felling
G Holding strap notch.
The holding strap supports the tree and helps prevent it
– The width of the cuts is 1/10 of the trunk diameter.
from falling prematurely. The width of the holding strap is
1/10 to 1/5 of the trunk diameter. The trunk does not splinter when the tree falls.

11.5.5 Plunge cutting

11.5.4 Cutting the felling notch
Plunge cutting is a technique required for felling.
The felling notch determines the direction in which the tree
falls. Country-specific standards for making the felling notch
must be observed.

26 0458-809-0121-A
11 Operating the Saw English

1.

0000-GXX-1253-A0
0000-GXX-1252-A0
3.
1 2
2.

► Begin cut with the lower portion of the guide bar nose –
with chain running at full speed. 1 Normal tree
A normal tree is vertical and has an even crown.
► Cut until depth of kerf is twice the width of the guide bar.
► Swing the saw into plunge-cutting position. 2 Leaner
A leaner stands at an angle and the crown faces in the
► Perform the plunge cut
direction of fall.
11.5.6 Selecting the Appropriate Felling Cut
11.5.7 Felling normal, small diameter tree
The choice of appropriate felling cut depends on the
following conditions: A normal tree is felled with a felling cut and stabilizing strap.
This felling cut must be performed if the tree diameter is less
– The natural inclination of the tree than the guide bar’s length.
– The tree’s branch formation ► Shout a warning.
– Damage to the tree
– The tree’s state of health
1.
– If there is snow on the tree: the snow load 2.

– The direction of slope

– Wind direction and speed
– Nearby trees, if any

0000-GXX-1254-A0
There are different features of these conditions. Only two
features are described in this Instruction Manual.

► Plunge the guide bar into the felling cut until it is visible at
the other side of the trunk, @ 11.5.5.
► Apply the spiked bumper behind the hinge and use it as a
pivot.
► Enlarge felling cut in direction of hinge.

0458-809-0121-A 27
English 11 Operating the Saw

► Enlarge felling cut in direction of stabilizing strap. ► Hold the saw horizontally and swing it into the felling cut
as far as possible.
► Enlarge felling cut in direction of hinge.
3.
► Enlarge felling cut in direction of stabilizing strap.
► Move to the other side of the tree.
► Plunge the guide bar into the felling cut at the same
height.
► Enlarge felling cut in direction of hinge.

0000-GXX-1255-A0
► Enlarge felling cut in direction of stabilizing strap.

► Insert a felling wedge. The felling wedge must match the 6.

tree diameter and the width of the felling cut.
► Shout a warning.
► With outstretched arms, cut through the stabilizing strap
horizontally from outside at the same level as the felling

0000-GXX-1257-A0
cut.
The tree falls.

11.5.8 Felling normal, large diameter tree

A normal tree is felled with a felling cut and stabilizing strap. ► Insert a felling wedge. The felling wedge must match the
This felling cut must be performed if the tree diameter is tree diameter and the width of the felling cut.
greater than the guide bar’s length. ► Shout a warning.
► Shout a warning. ► With outstretched arms, cut through the stabilizing strap
horizontally from outside at the same level as the felling
cut.
The tree falls.

11.5.9 Felling a small diameter leaner

1. 4. 5. A leaner is felled with a felling cut and holding strap. This
2. felling cut must be performed if the tree diameter is less than
3.
the guide bar’s length.
0000-GXX-1256-A0

► Shout a warning.

► Apply the spiked bumper at the same height as the felling

cut and use it as a pivot.

28 0458-809-0121-A
11 Operating the Saw English

1. 2.

1.
2. 3. 5. 6.
4.

0000-GXX-1260-A0
0000-GXX-1258-A0
► Plunge the guide bar into the felling cut until it is visible at ► Apply the spiked bumper behind the holding strap at the
the other side of the trunk, @ 11.5.5. same height as the felling cut and use it as a pivot.
► Enlarge felling cut in direction of hinge. ► Hold the saw horizontally and swing it into the felling cut
► Enlarge felling cut in direction of holding strap. as far as possible.
► Enlarge felling cut in direction of hinge.
► Enlarge felling cut in direction of holding strap.
► Move to the other side of the tree.
► Apply the spiked bumper behind the hinge at the same
height as the felling cut and use it as a pivot.
► Hold the saw horizontally and swing it into the felling cut
as far as possible.
0000-GXX-1259-A0

► Enlarge felling cut in direction of hinge.

► Enlarge felling cut in direction of holding strap.

► Shout a warning.
► With arms outstretched, cut through the holding strap from
outside at a downward angle.
The tree falls.

11.5.10 Felling a large diameter leaner

0000-GXX-1261-A0
A leaner is felled with a felling cut and holding strap. This
felling cut must be performed if the tree diameter is greater
than the guide bar’s length.
► Shout a warning.
► Shout a warning.

0458-809-0121-A 29
English 12 After Finishing Work

► With arms outstretched, cut through the holding strap from ► Observe the following points when storing the saw:
outside at a downward angle. – Saw is out of the reach of children.
The tree falls.
– The saw is clean and dry.

If you store the saw for more than 3 months:

12 After Finishing Work ► Remove the bar and chain.
► Open the fuel tank cap.
12.1 After Finishing Work ► Drain the fuel tank.
► Shut off the engine and engage the chain brake. ► Close the fuel tank.
► Allow chainsaw to cool down. ► Have fuel tank cleaned by a STIHL servicing dealer.
► If the saw is wet: Allow the saw to dry. ► Start the engine, engage the chain brake and run the
► Clean the saw. engine at idling speed until it stops.
► Clean the bar and chain.
► Loosen nuts on the chain sprocket cover. 15 Cleaning
► Turn the tensioning screw two full turns counterclockwise.
The chain is now slack.
► Tighten down nuts on the chain sprocket cover. 15.1 Cleaning the Saw
► Fit the scabbard so that it completely covers the guide bar. ► Shut off the engine and engage the chain brake.
► Allow chainsaw to cool down.
► Clean the saw with a damp cloth or STIHL resin solvent.
13 Transporting ► Clean cooling air slots with a soft brush.

13.1 Transporting the Chainsaw 4 2

► Shut off the engine and engage the chain brake.
► Fit the scabbard so that it completely covers the guide bar. 3 1
► Carry the saw by holding the front handle in your right
hand with the guide bar pointing to the rear.
► Transporting the saw in a vehicle: Secure the saw to

0000-GXX-5818-A0
prevent turnover and movement.

14 Storing
► Rotate the filter cover lock (1) a quarter turn
counterclockwise.
14.1 Storing the Chainsaw ► Remove the filter cover (2).
► Shut off the engine and engage the chain brake. ► Rotate the shroud lock (1) a quarter turn
► Fit the scabbard so that it completely covers the guide bar. counterclockwise.

30 0458-809-0121-A
15 Cleaning English

► Remove the shroud (4). 15.3 Cleaning the Air Filter

► Remove the chain sprocket cover. Very fine dust can collect in the air filter. The dust can clog
► Use a soft brush, damp cloth or STIHL resin solvent to the filter and cannot be removed by brushing or knocking
clean the cylinder fins and the inside of the shroud. out. The air filter must be cleaned with a cleaning agent.
► Clean the area around the sprocket with a damp cloth or ► Shut off the engine and engage the chain brake.
STIHL resin solvent.
► Place the shroud (4) in position.
► Rotate the shroud lock (3) clockwise until you hear a click.
The shroud lock (3) is secure.
1
► Fit the filter cover (2). 2
► Rotate the filter cover lock (1) clockwise until you hear a 3
click.

0000-GXX-5819-A0
The filter cover lock (1) is secure.
► Fit the chain sprocket cover.

15.2 Cleaning the Bar and Chain

► Rotate the filter cover lock (1) a quarter turn
► Shut off the engine and engage the chain brake. counterclockwise.
► Remove the bar and chain. ► Remove the filter cover (2).
► Clean the area around the air filter (3) with a damp cloth
or a soft brush.
3 ► Remove the air filter (3).
1
► Rinse away coarse dirt from the outside of the filter (3)
under running water.
► If the air filter (3) is damaged. Install a new air filter (3).
0000-GXX-2951-A0

WARNING
2 3 Cleaning agent may cause irritation if it contacts the skin or
eyes.
► Observe the information supplied with the cleaning agent.
► Clean the oil port (1), oil inlet hole (2) and bar groove (3)
► Avoid contact with cleaning agents.
with a soft brush or STIHL resin solvent.
► In case of contact with the skin: Wash affected areas with
► Clean the saw chain with a soft brush or STIHL resin plenty of water and soap.
solvent. ► In case of contact with the eyes: Rinse eyes with plenty of
► Mount the bar and chain. water for at least 15 minutes and seek medical advice.

► Spray the outside and inside of the air filter (3) with STIHL
special cleaner or a cleaning agent with a pH value higher
than 12.

0458-809-0121-A 31
English 15 Cleaning

► Allow STIHL special cleaner or cleaning agent to act for 10 ► Rotate the filter cover lock (1) a quarter turn
minutes. counterclockwise.
► Use a soft brush to clean the outside of the air filter (3). ► Remove the filter cover (2).
► Rinse the outside and inside of the air filter (3) under ► Rotate the shroud lock (1) a quarter turn
running water. counterclockwise.
► Allow air filter (3) to dry in the air. ► Remove the shroud (4).
► Pull off the spark plug boot (5).
3 ► If area around the spark plug is dirty: Clean it with a damp
cloth.
1
► Unscrew the spark plug.
2
► Clean the spark plug with a damp cloth.
► If the spark plug is corroded: Install a new spark plug.

0000-GXX-5820-A0
► Push the air filter (3) into place by hand.
► Fit the filter cover (2).
6

0000-GXX-5822-A0
► Rotate the filter cover lock (1) clockwise until you hear a
click. 5
The filter cover lock (1) is secure.

15.4 Cleaning the Spark Plug ► Fit the spark plug and tighten it down firmly.
► Shut off the engine and engage the chain brake. ► Position the spark plug boot (5) so that the lug (6) points
► Allow chainsaw to cool down. vertically upwards.
► Press the spark plug boot (5) firmly home.
4 3 ► Place the shroud (4) in position.
2 1 ► Rotate the shroud lock (3) clockwise until you hear a click.
5 The shroud lock (3) is secure.
► Fit the filter cover (2).
► Rotate the filter cover lock (1) clockwise until you hear a
click.
0000-GXX-5821-A0

The filter cover lock (1) is secure.

32 0458-809-0121-A
16 Maintenance English

► If you have any queries: Contact your STIHL servicing

16 Maintenance dealer.

16.1 Maintenance Intervals 16.3 Sharpening the Saw Chain

The maintenance intervals are dependent on the Correctly sharpening saw chains requires a lot of practice.
environmental and operating conditions. STIHL STIHL files, STIHL filing aids, STIHL sharpeners and the
recommends the following maintenance intervals: brochure “Sharpening STIHL Saw Chains” help you achieve
the right results. To obtain the brochure visit
Chain brake http://www.stihl.com/sharpening-brochure.
► Have the chain brake serviced by a STIHL servicing STIHL recommends you have saw chains resharpened by a
dealer at the following intervals: STIHL servicing dealer.
– Full-time usage: every 3 months
– Part-time usage: every 6 months WARNING
– Occasional usage: every 12 months The chain's cutters are very sharp. There is a risk of cut
injuries.
After every 100 hours of operation
► Wear work gloves made of durable material.
► Install a new spark plug.

Weekly
► Check the chain sprocket.
► Check and deburr the guide bar.
► Check and sharpen the saw chain.

Monthly
► Clean the air filter.

0000-GXX-1219-A0
► Have oil tank cleaned by a STIHL servicing dealer.
► Have fuel tank cleaned by a STIHL servicing dealer.
► Have pickup body (filter) in fuel tank cleaned by a STIHL
servicing dealer. ► File each cutter with a round file so that the following
points are observed:
Every 12 months
– Round file matches the chain pitch.
► Have pickup body (filter) in fuel tank replaced by a STIHL – File from the inside to the outside of the cutter.
servicing dealer.
– Hold the file at right angle to the guide bar.
– Maintain a filing angle of 30°.
16.2 Deburring the Guide Bar
A burr can build up on the outer edge of the guide bar.
► Remove burr with a flat file or a STIHL guide bar dressing
tool.

0458-809-0121-A 33
English 17 Repairing

0000-GXX-1220-A1
► File down the depth gauges with a flat file so that they are
level with the STIHL filing gauge and parallel to the service
mark. The STIHL filing gauge must match the chain pitch.
► If you have any queries: Contact your STIHL servicing
dealer for assistance.

17 Repairing

17.1 Repairing the Chain Saw, Guide Bar and Saw

Chain
The chain saw, guide bar and saw chain cannot be repaired
by the user.
► If the saw, guide bar or saw chain is damaged: Do not use
your saw, guide bar or saw chain, and contact your STIHL
servicing dealer.

34 0458-809-0121-A
18 Troubleshooting English

18 Troubleshooting

18.1 Troubleshooting Chainsaw

Most malfunctions have the same causes.
► Perform the following operations:
► Clean the air filter.
► Clean or replace the spark plug.
► Perform 5 uniform bucking cuts at full throttle.
The engine adjusts itself automatically to ambient conditions.
► If the malfunction still exists: Take the action described in the following table.
Condition Cause Remedy
Engine does not start. Insufficient fuel in the tank. ► Mix fuel and refuel the chainsaw.
Engine is flooded. ► Clear the combustion chamber.
Poor acceleration The chain is over- ► Tension chain properly.
tensioned.
Chain lubrication system ► Increase oil feed rate.
is supplying insufficient
chain oil.
Saw chain does not rotate The chain brake is ► Disengage the chain brake.
when throttle is opened. engaged.
The chain is over- ► Tension chain properly.
tensioned.
Bar nose sprocket is ► Clean the bar nose sprocket with STIHL resin solvent.
blocked.
Smoke or burning smell Chain is not properly ► Sharpen the chain properly.
while cutting. sharpened.
Insufficient chain oil in the ► Fill up with chain oil.
tank.
Chain lubrication system ► Increase oil feed rate.
is supplying insufficient
chain oil.
The chain is over- ► Tension chain properly.
tensioned.
Chainsaw is not being ► Have correct use explained, then practice.
used properly.

0458-809-0121-A 35
English 18 Troubleshooting

18.2 Clearing the Combustion Chamber

► Engage the chain brake.

4 3 6
2 1

0000-GXX-5822-A0
5 5

0000-GXX-5821-A0
► Position the spark plug boot (5) so that the lug (6) points
vertically upwards.
► Press the spark plug boot (5) firmly home.
► Place the shroud (4) in position.
► Rotate the filter cover lock (1) a quarter turn ► Rotate the shroud lock (3) clockwise until you hear a click.
counterclockwise. The shroud lock (3) is secure.
► Remove the filter cover (2). ► Fit the filter cover (2).
► Rotate the shroud lock (1) a quarter turn ► Rotate the filter cover lock (1) clockwise until you hear a
counterclockwise. click.
► Remove the shroud (4). The filter cover lock (1) is secure.
► Pull off the spark plug boot (5).
► Unscrew the spark plug.
► Dry the spark plug.

WARNING
Unconfined sparks may occur if the starter grip is pulled after
the spark plug boot has been removed. Sparks may cause a
fire or an explosion in an easily combustible or explosive
environment. This can result in serious or fatal injuries and
damage to property.
► Depress the stop switch and keep it depressed before
pulling the starter grip.

► Depress the stop switch and hold it in that position.

► Pull the starter grip and guide it back several times.
The combustion chamber is cleared.
► Insert and tighten down the spark plug.

36 0458-809-0121-A
19 Specifications English

– Vibration level ahv measured according to ISO 22867:

19 Specifications – Front handle (handlebar): 4.2 m/s² K-value (uncertainty)
for vibration level is 2 m/s².
– Rear handle: 4.0 m/s² K-value (uncertainty) for vibration
19.1 STIHL MS 500i Chainsaw level is 2 m/s².
– Displacement: 79.2 cc
– Engine power to ISO 7293: 5.0 kW (6.8 bhp) For further details on compliance with Vibration Directive
2002/44/EC visit www.stihl.com/vib.
– Idle speed to ISO 11681: 3,000 ± 50 rpm
– Approved spark plug: NGK CMR6H from STIHL
19.5 REACH
– Electrode gap: 0.5 mm REACH is an EC regulation and stands for the Registration,
– Dry weight without guide bar and chain Evaluation, Authorisation and Restriction of Chemical
substances.
– MS 500i: 6.2 kg
– MS 500i with handle heating: 6.3 kg For information on compliance with the REACH regulation
see www.stihl.com/reach.
– Max. fuel tank capacity: 785 cc (0.785 l)
– Max. oil tank capacity: 325 cc (0.325 l)
19.6 Exhaust Emissions
The CO2value measured in the EU type approval procedure
19.2 Chain Sprockets and Chain Speeds is specified at www.stihl.com/co2.
The following chain sprockets may be used:
The measured CO2value was determined on a
– 7-tooth for 3/8" representative engine in accordance with a standardized
test procedure under laboratory conditions and does not
– Maximum chain speed according to ISO 11681:
represent either an explicit or implied guarantee of the
28.9 m/s
performance of a specific engine.
– Chain speed at maximum power: 21.7 m/s
The applicable exhaust emission requirements are fulfilled
by the intended usage and maintenance described in this
19.3 Minimum Groove Depth of Guide Bars instruction manual. The type approval expires if the engine
The minimum groove depth depends on the pitch of the is modified in any way.
guide bar.
– 3/8" 6 mm

19.4 Noise and Vibration Data

– Sound pressure level L p measured according to
ISO 22868: 106 dB(A) K-value (uncertainty) for noise
pressure level is 2 dB(A).
– Sound power level Lw measured according to ISO 22868:
119 dB(A) K-value (uncertainty) for sound power level is 2
dB(A).

0458-809-0121-A 37
English 20 Bar and Chain Combinations

20 Bar and Chain Combinations

20.1 STIHL MS 500i Chainsaw

Pitch Drive link Length Guide bar Nose sprocket Number of drive Saw chain
gauge/groove teeth links
width
Rollomatic E
11
40 cm Rollomatic ES 60
Duromatic -
Rollomatic E
11
45 cm Rollomatic ES 66
Duromatic -
Rollomatic E
Rollomatic ES 11 36 RS (Type 3621)
50 cm 72
Rollomatic ES Light
36 RS3 (Type 3626)
Duromatic -
36 RM (Type 3652)
3/8” 1.6 mm Rollomatic ES 11
55 cm 76 36 RM3 (Type
Duromatic -
3664)
Rollomatic E
Rollomatic ES 11 36 RD3 (Type 3683)
63 cm 84
Rollomatic ES Light
Duromatic -
Rollomatic ES
71 cm 11 91
Rollomatic ES Light
75 cm Duromatic - 98
80 cm Rollomatic ES Light 11 105
90 cm Rollomatic ES Light 11 114
The cutting length of a guide bar depends on the chainsaw and the saw chain being used. Actual cutting length may be less
than the specified length

38 0458-809-0121-A
21 Spare Parts and Accessories English

– Serial identification: 1147

21 Spare Parts and Accessories – Displacement: 79.2 cc

conforms to the relevant provisions of Directives

21.1 Spare Parts and Accessories 2011/65/EU, 2006/42/EC, 2014/30/EU and 2000/14/EC and
These symbols identify original STIHL has been developed and manufactured in compliance with
replacement parts and original STIHL the following standards in the versions valid on the date of
accessories. production: EN ISO 11681-1, EN 55012 and EN 61000-6-1.

STIHL recommends the use of original STIHL replacement The EC type examination in accordance with Directive
parts and accessories. 2006/42/EC Article 12.3(b) was carried out at: DPLF,
Deutsche Prüf- und Zertifizierungsstelle für Land- und
Original STIHL replacement parts and original STIHL Forsttechnik GbR (NB 0363), Spremberger Straße 1,
accessories are available from STIHL servicing dealers. 64823 Groß-Umstadt, Germany
– Certification number K-EG -2017/8346
22 Disposal The measured and guaranteed sound power levels were
determined according to Directive 2000/14/EC, Annex V,
using the ISO 9207 standard.
22.1 Disposing of Chainsaw
Information on disposal is available from STIHL servicing – Measured sound power level: 119 dB(A)
dealers. – Guaranteed sound power level: 121 dB(A)
► Dispose of the chainsaw, guide bar, saw chain, fuel mix,
gasoline, two-stroke engine oil, accessories and Technical documents are deposited at ANDREAS STIHL AG
packaging in accordance with local regulations and & Co. KG Produktzulassung (Product Licensing).
environmental requirements. The year of manufacture and serial number are applied to
the chainsaw.

23 EC Declaration of Conformity Done at Waiblingen, 16.01.2019

ANDREAS STIHL AG & Co. KG

23.1 STIHL MS 500i Chainsaw

ANDREAS STIHL AG & Co. KG
Badstrasse 115
D-71336 Waiblingen
Germany
Thomas Elsner, Director Product Management and Services
declare in exclusive responsibility that
– Category: Chainsaw
– Make: STIHL
– Model: MS 500i, MS 500i W

0458-809-0121-A 39
English 23 EC Declaration of Conformity

40 0458-809-0121-A
0458-809-0121-A
englisch
G

www.stihl.com

*04588090121A*
0458-809-0121-A