Elastic Bending Theory Sayfa 1 / 7

Disclaimer: The information on this page has not been checked by an independent person. Use this information at
your own risk.
ROYMECH
Load and stress testing Strain Measurement Machine Vibration Basics Radiation oncolo
More than 1600 satisfied System Computer Based Training - Get the latest news
customers! Download Product Patented, proven system to Vibration Monitoring and Vibration oncology!
Evaluation. measure surface strain and Analysis Radiation.AuntMinni
www.radview.com geometry www.newstandardinstitute.c ...
www.asametech.com
Ads by Google Adver

Home
Beams Index

Elastic Bending Theory

Introduction.... Superposition.... Nomenclature.... Simple Bending.... Deflection.... Area Moment Method....

Introduction

The stress, strain, dimension, curvature, elasticity, are all related, under certain assumption, by the theory of simple
bending. This theory relates to beam flexure resulting from couples applied to the beam without consideration of the
shearing forces.

Superposition Principle

The superposition principle is one of the most important tools for solving beam loading problems allowing simplification of
very complicated design problems..

For beams subjected several loads of different types the resulting shear force, bending moment, slope and deflection can
be found at any location by summing the effects due to each load acting separately to the other loads.

Nomenclature

e = strain
E = Young's Modulus = σ /e (N/m2)
y = distance of surface from neutral surface (m).
R = Radius of neutral axis (m).
I = Moment of Inertia (m4 - more normally cm4)
Z = section modulus = I/ymax(m3 - more normally cm3)
F = Force (N)
x = Distance along beam
δ = deflection (m)
θ = Slope (radians)
σ = stress (N/m2)

Simple Bending

A straight bar of homogeneous material is subject to only a moment at one end and an equal and opposite moment at the
other end...

http://www.roymech.co.uk/Useful_Tables/Beams/Beam_theory.html 03.03.2007
Elastic Bending Theory Sayfa 2 / 7

Assumptions

The beam is symmetrical about Y-Y

The traverse plane sections remain plane and normal to the longitudinal fibres after bending (Beroulli's assumption)
The fixed relationship between stress and strain (Young's Modulus)for the beam material is the same for tension and
compression ( σ= E.e )

Consider two section very close together (AB and CD).

After bending the sections will be at A'B' and C'D' and are no longer parallel. AC will have extended to A'C' and BD will
have compressed to B'D'
The line EF will be located such that it will not change in length. This surface is called neutral surface and its intersection
with Z_Z is called the neutral axis
The development lines of A'B' and C'D' intersect at a point 0 at an angle of θ radians and the radius of E'F' = R
Let y be the distance(E'G') of any layer H'G' originally parallel to EF..Then

H'G'/E'F' =(R+y)θ /R θ = (R+y)/R

And the strain e at layer H'G' =

e = (H'G'- HG) / HG = (H'G'- HG) / EF = [(R+y)θ - R θ] /R θ = y /R

The accepted relationship between stress and strain is σ= E.e Therefore

σ = E.e = E. y /R
σ/E=y/R

Therefore, for the illustrated example, the tensile stress is directly related to the distance above the neutral axis. The
compressive stress is also directly related to the distance below the neutral axis. Assuming E is the same for compression
and tension the relationship is the same.

As the beam is in static equilibrium and is only subject to moments (no vertical shear forces) the forces across the section
(AB) are entirely longitudinal and the total compressive forces must balance the total tensile forces. The internal couple
resulting from the sum of ( σ.dA .y) over the whole section must equal the externally applied moment.

http://www.roymech.co.uk/Useful_Tables/Beams/Beam_theory.html 03.03.2007
Elastic Bending Theory Sayfa 3 / 7

This can only be correct if Σ(yδa) or Σ(y.z.δy) is the moment of area of the section about the neutral axis. This can only
be zero if the axis passes through the centre of gravity (centroid) of the section.

The internal couple resulting from the sum of ( σ.dA .y) over the whole section must equal the externally applied
moment. Therefore the couple of the force resulting from the stress on each area when totalled over the whole area will
equal the applied moment

From the above the following important simple beam bending relationship results

It is clear from above that a simple beam subject to bending generates a maximum stress at the surface furthest away from
the neutral axis. For sections symmetrical about Z-Z the maximum compressive and tensile stress is equal.

σmax = ymax. M / I

The factor I /ymax is given the name section Modulus (Z) and therefore

σmax = M / Z

Values of Z are provided in the tables showing the properties of standard steel sections

Deflection of Beams

Below is shown the arc of the neutral axis of a beam subject to bending.

For small angle dy/dx = tan θ = θ

The curvature of a beam is identified as dθ /ds = 1/R
In the figure δθ is small and δx; is practically = δs; i.e ds /dx =1

http://www.roymech.co.uk/Useful_Tables/Beams/Beam_theory.html 03.03.2007
Elastic Bending Theory Sayfa 4 / 7

From this simple approximation the following relationships are derived.

Integrating between selected limits.

The deflection between limits is obtained by further integration.

It has been proved ref Shear - Bending that dM/dx = S and dS/dx = -w = d2M /dx
Where S = the shear force M is the moment and w is the distributed load /unit length of beam. therefore

If w is constant or a integratatable function of x then this relationship can be used to arrive at general expressions for S, M,
dy/dx, or y by progressive integrations with a constant of integration being added at each stage. The properties of the
supports or fixings may be used to determine the constants. (x= 0 - simply supported, dx/dy = 0 fixed end etc )

In a similar manner if an expression for the bending moment is known then the slope and deflection can be obtained at any
point x by single and double integration of the relationship and applying suitable constants of integration.

Singularity functions can be used for determining the values when the loading a not simple ref Singularity Functions

Example - Cantilever beam

Consider a cantilever beam (uniform section) with a single concentrated load at the end. At the fixed end x = 0, dy = 0 ,
dy/dx = 0

From the equilibrium balance ..At the support there is a resisting moment -FL and a vertical upward force F.
At any point x along the beam there is a moment F(x - L) = Mx = EI d 2y /dx 2

http://www.roymech.co.uk/Useful_Tables/Beams/Beam_theory.html 03.03.2007
Elastic Bending Theory Sayfa 5 / 7

Example - Simply supported beam

Consider a simply supported uniform section beam with a single load F at the centre. The beam will be deflect
symmetrically about the centre line with 0 slope (dy/dx) at the centre line. It is convenient to select the origin at the centre
line.

Moment Area Method

This is a method of determining the change in slope or the deflection between two points on a beam. It is expressed as two
theorems...

Theorem 1
If A and B are two points on a beam the change in angle (radians) between the tangent at A and the tangent at B is equal to
the area of the bending moment diagram between the points divided by the relevant value of EI (the flexural rigidity
constant).

Theorem 2
If A and B are two points on a beam the displacement of B relative to the tangent of the beam at A is equal to the moment of
the area of the bending moment diagram between A and B about the ordinate through B divided by the relevant value of EI
(the flexural rigidity constant).

Examples ..Two simple examples are provide below to illustrate these theorems

Example 1) Determine the deflection and slope of a cantilever as shown..

http://www.roymech.co.uk/Useful_Tables/Beams/Beam_theory.html 03.03.2007
Elastic Bending Theory Sayfa 6 / 7

The bending moment at A = MA = FL

The area of the bending moment diagram AM = F.L2 /2
The distance to the centroid of the BM diagram from B= xc = 2L/3
The deflection of B = y b = A M.x c /EI = F.L 3 /3EI
The slope at B relative to the tan at A = θ b =AM /EI = FL2 /2EI

Example 2) Determine the central deflection and end slopes of the simply supported beam as shown..

E = 210 GPa ......I = 834 cm4...... EI = 1,7514. 10 6Nm 2

A1 = 10.1,8.1,8/2 = 16,2kNm
A2 = 10.1,8.2 = 36kNm
A2 = 10.1,8.2 = 36kNm
A1 = 10.1,8.1,8/2 = 16,2kNm
x1 = Centroid of A1 = (2/3).1,8 = 1,2
x2 = Centroid of A2 = 1,8 + 1 = 2,8
x3 = Centroid of A3 = 1,8 + 1 = 2,8
x4 = Centroid of A4 = (2/3).1,8 = 1,2

The slope at A is given by the area of the moment diagram between A and C divided by EI.

θA = (A1 + A2) /EI = (16,2+36).10 3 / (1,7514. 10 6)

= 0,029rads = 1,7 degrees

The deflection at the centre (C) is equal to the deviation of the point A above a line that is tangent to C.
Moments must therefore be taken about the deviation line at A.

δC = (AM.xM) /EI = (A1 x1 +A2 x2) / EI = 120,24.10 3/ (1,7514. 10 6)

http://www.roymech.co.uk/Useful_Tables/Beams/Beam_theory.html 03.03.2007
Elastic Bending Theory Sayfa 7 / 7

= 0,0686m = 68,6mm

Sites Providing Relevant Information Ads by Google

Mood Beam
1. Beams, strain, stress , deflections...U of Washington . PDF download with lots of useful information Steel Beams
2. Pure Bending...Mississipi State U. Pure Bending Lecture Notes.. very useful Beam Sections
3. Review of Simple beam theory...MIT Powerpoint presentation.. Strain Guage
4. Lecture Notes for structural Design...U of Toronto - Lots of useful notes on beam theory and design Load Cells UK

This page is being developed

Home
Beams Index

Please Send Comments to [email protected]

Last Updated 17/10/2006

http://www.roymech.co.uk/Useful_Tables/Beams/Beam_theory.html 03.03.2007