It8951 Usb Faq

IT8951 Basic Operation and
Frequently Asked Questions
2017 Dec.
Version v.0.2
 Revision history
Revision History
Version Date Description Modified by
0.1 2017 Nov. Document created Richard Chen
0.2 2017 Dec. v.0.2 released Richard Chen
1
 Summary
The IT8951, EPD timing controller for product of E-ink, can take
command from host through supported interfaces that include I2C, SPI
and USB.
For driving E-ink EPD through IT8951, please contact us to get

corresponding firmware. The different EPD may need different firmware
to make IT8951 be able to drive it.
There are different host platforms can implement the control of

IT8951. To remain the flexibility, we do not prepare the coding resource
for specific platform, like Linux or Android; that is, there has no preferred
host environment. You can control IT8951 by any system you want to use
as long as the chosen communication method is realizable on it.
We also provide demo application and sample code of USB and of

SPI. Please notice that the demo application was built for checking the
working status of IT8951; the sample code are provided as referring
resource for C language developing; neither of them is provided as
implementation resource of Windows system. Again, you can implement
the control of IT8951 on any host platform you want.
For the command formats of USB and of SPI, provided programming

guide document has detailed introduction. Reading these documents
before start to develop would make everything easier.
2
 Basic Operation
USB
1. Check if the used host device supports USB device connection.
No hint will be shown as the IT8951 being connected to the host
device; but it’s visible in your OS.
2. Implement needed function for sending SCSI command to a

device through USB interface and then send SCSI command to
the IT8951.
3. It should work normally if the sent SCSI command meets the

required format described in IT8951 USB Programming Guide.
Please refer to the documents we provided.
3
 FAQ
IT8951 & E-ink EPD
Q: How to start to use IT8951?
A: At first, please confirm the used EPD model. It’s recommended to

contact us (and the E-ink) for reviewing the circuit wiring to ensure the
IT8951 (and EPD) can work. You can also get helpful suggestion of
product development from us.
We’ll release firmware to you for the requested EPD model. If any
customized function is needed, please feel free to discuss with us.
Q: The maximum supported resolution of IT8951?
A: IT8951 supports resolution up to 2048x2048. The higher resolution

requires the larger flash space.
If the height or width over 2048, it still can supports as long as the
(width x height) is not over (2048 x 2048). In this case, please provide
the panel frame rate to check if the CPU of IT8951 is able to support it.
Q: Can the IT8951 show a certain image as it startup?
A: Yes, we can write the assigned image into flash. For this function,
please contact us and provide the required image. The image file should
be a 4bpp raw data.
4
Q: I just cannot use IT8951. Is it breakdown?
A: We provided a demo application to check the working status of IT8951

through Windows USB interface. Please use it for checking first.
The most common reason is the incorrect command format that

cannot be recognized by IT8951. Please refer to the Programming Guide
files we provided.
In some case, the reason is that IT8951 wasn’t powered properly

(even not be powered), or some problem within circuit. We also provide
service of review circuit for avoiding this.
Q: The latest firmware version has not the function I asked for.
A: Please remember to restart IT8951 after upgrading the firmware.
If the new firmware doesn’t work or doesn’t meet your request,

please contact to us.
5
USB
Q: After connecting to the host device, I cannot see where the

directory of IT8951 is. How can I open it? Should I install any
driver?
A: The IT8951 will be considered as a mass storage device as long as the

host device supports USB interface. To control it, just send SCSI
command to it through USB interface of host device; the IT8951 demo
application is useful to check if the IT8951 is working normally.
Q: I sent SCSI command to it but didn’t get any response.
A: It’s probably that the sent command has a wrong format so IT8951
cannot recognize it; or the command was sent to a wrong object.
Please check following:
- If the host device can choose an object to send command, ensure

that the target is really IT8951.
- Check if the sent command format is correct according to IT8951

USB Programming Guide.
Q: Will the USB sample code that can be executed on our host
platform (Linux, Android…) be provided?
A: There are different host platforms able to control IT8951 through USB
interface; we didn’t build demo model on every probable devices. The
provided sample code and demo application were built on Windows
system, but the command format is general.

It8951 Usb Faq

Uploaded by

Copyright:

Available Formats

It8951 Usb Faq

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

It8951 Usb Faq

Uploaded by

Copyright:

Available Formats

IT8951 Basic Operation and

Frequently Asked Questions

Version Date Description Modified by

0.1 2017 Nov. Document created Richard Chen

0.2 2017 Dec. v.0.2 released Richard Chen

For driving E-ink EPD through IT8951, please contact us to get

There are different host platforms can implement the control of

We also provide demo application and sample code of USB and of

For the command formats of USB and of SPI, provided programming

2. Implement needed function for sending SCSI command to a

3. It should work normally if the sent SCSI command meets the

IT8951 & E-ink EPD

Q: How to start to use IT8951?

A: At first, please confirm the used EPD model. It’s recommended to

Q: The maximum supported resolution of IT8951?

A: IT8951 supports resolution up to 2048x2048. The higher resolution

Q: Can the IT8951 show a certain image as it startup?

A: We provided a demo application to check the working status of IT8951

The most common reason is the incorrect command format that

In some case, the reason is that IT8951 wasn’t powered properly

A: Please remember to restart IT8951 after upgrading the firmware.

If the new firmware doesn’t work or doesn’t meet your request,

Q: After connecting to the host device, I cannot see where the

A: The IT8951 will be considered as a mass storage device as long as the

Q: I sent SCSI command to it but didn’t get any response.

Please check following:

- If the host device can choose an object to send command, ensure

- Check if the sent command format is correct according to IT8951

You might also like