Apex Revision June

RIGGING GUIDE &
LIFTING PRODUCTS
340 Henry St. Tel: 519-751-8085

Unit# 1 Fax: 519-751-8005
Brantford, Ontario
N3S 7V9
www.apexchain.com
APEX CHAIN AND CABLE INC.
PRODUCT LINE CARD

***PLEASE INQUIRE ABOUT OUR COMPLIMENTARY INSPECTIONS***
ACCO-ANVER VACU-LIFTS, LOUDEN
ACTEK MFG. IMPERIAL & METRIC HOIST RINGS
BUDGIT CHAIN & WIRE ROPE HOISTS
CAMPBELL CHAIN, SLINGS, COMPONENTS
CAN-AM CASTERS / COLSON FULL LINE OF CUSTOM QUALITY CASTERS
CARR-LANE JIG & FIXTURE TOOLING COMPONENTS
COLUMBUS McKINNON CHAIN PULLERS, HOISTS & ALLOY COMPONENTS
CROSBY SHACKLES, WIRE ROPE FITTINGS, HOIST RINGS,
GLEASON REEL HOSE & CABLE REELS
APEX RIGGING COMPONENT CHAIN SLINGS, CRANE CABLES,

CUSTOM WIRE ROPE SLINGS, AND GENERAL PURPOSE
WIRE ROPE
APEX SYNTHETIC SLINGS NYLON, POLYESTER, BALLISTIC, AND ROUND SLINGS
INTER-PRODUCT / RENFROE / MERRILL LIFTING CLAMPS
IGUS POWER TRACK & IGLIDE
SERVICES: CERTIFICATION / PROOFTESTING CERTIFICATION AND PROOFTESTING OF DEVICES
CERTIFIED CUSTOM DEVICES SPECIALIZED LIFTING COMPONENTS
LIFT ALL MESH SLINGS, LOAD HUGGERS
McKISSICK SHEAVES & BLOCKS
TECNOMAGNETE PERMANENT LIFTING MAGNETS AND WORK HOLDING
TRACTEL FALL ARREST, LOAD MEASURE EQUIPMENT
STAINLESS STEEL FITTINGS, WIRE ROPE, CUSTOM ASSEMBLIES

& CUSTOM LIFTING DEVICES
YOKE ALLOY CHAIN COMPONENTS
THERN WINCH SPECIALISTS
***DELIVERED TO YOU BY OUR TRAINED PROFESSIONALS***
***COMPLETE CATALOGS AVAILABLE UPON REQUEST***

SYNTHETIC SLINGS
HOW TO ORDER SLINGS

Style of hitch to be used
Slings can be used in any of the three hitches illustrated. Some slings are designed to be used in
a specific hitch application only.
Vertical Choker Basket
Maximum weight to be lifting

Determine the maximum amount of weight you are lifting and then use the ratings chart to determine
the size of the sling you will need to use.
Determine the type of webbing you will use
Treated Nylon is the most Treated Polyester can be safely Treated Super Edge Nylon
popular webbing used for web used with acids, excluding has the same specifications as
slings. Nylon is not suitable to use concentrated sulfuric acid, strong Nylon. An added feature is black
with acids or bleaching agents. It alkalis, aldehyde, and ethers. cordura edges to protect the sling
will stretch approximately 6-10% Polyester will stretch approximately against abrasion on the edges of
of the total length. 3-5% of sling length. the sling.
TS
G
DE
NS
NT ING
T IN
ER
EN
S
AR D
DE
BO
EN I N G
RU
O-C TE
S
OL
LVE AN
S E TE R &
AL N G
AT
IC A
S
ON
RG
NE
RS
CA RO-
DR NA
HY
S
LIS
DE &
AG AC H
S, C
SO LE
TS
OH
A LI
AW
A LK K
HY OGE
AP
RO
TO
HE
RB
LU ,
BR
TE
DE
YC
KA
A
ID
D
A LC
O IL
WE
WA
E
O IL
SO
HY
ST
KE
ET
L
AC
AL
DR
BL
HA
Chemical NYLON NO OK OK OK NO OK OK OK OK OK OK OK OK OK OK
Resistance POLYESTER OK NO OK OK NO OK OK OK OK OK OK OK OK
$EGRADEDBYCONCENTRATEDSULPHURICACID
$EGRADEDBYSTRONGALKALISATELEVATEDTEMPERATURES
Order using part numbers
E E 2 - 9 0 2 x 6' T-3
Sling Type Ply Webbing Width Length Type

Construction
11
SYNTHETIC SLINGS
Are wear pads required to protect the sling from damage?
Wear pads and sleeves provide extra protection and extend the life of your sling. Wear pads
should always be used when lifting on sharp corners.
GOOD BETTER BEST

Cordura Nylon Bulk Treated Nylon Ballistic Nylon
Bulk Treated Polyester
Polyester Tubing
Rubber
Leather
Sewn on wear pad is sewn directly in Sewn on wear pad. A wear pad
place to give fixed protection where it sewn directly inside the eye at the
wears the most. bearing point.
Sliding sleeve wear pad can be Full wrapped wear pad. Provides
positioned anywhere on the sling. Ideal total eye protection for rough
for handling sharp loads. attachment points.
Edge wrap wear pad is sewn along

both edges of the sling to protect from Velcro Type
edge wear and cutting.
Angle Strength Loss From Rated Capacity
Angle Angle CAUTION: SLING SHOULD FIT THE HOOK

Degrees Factor Degrees Factor On eye and eye type slings, the eyes must be of
ample length to easily slip over the crane hook,
thus reducing stress on stitching.
90° 1 55° 0.819
85° 0.996 50° 0.766
80° 0.985 45° 0.707
75° 0.966 40° 0.643 Reduction of sling
capacity depends on
70° 0.94 35° 0.574 the angle of the Sling
leg. See charts for
65° 0.906 30° 0.500 loss factor.
60° 0.866 Angle °
Rated capacities are affected by angle of lift (sling to load angle) measured from the horizontal when
used with multi-legged slings or choker/basket hitches. To determine the actual capacity at a given
angle of lift, multiply the original sling rating by the appropriate loss factor determined from the table
above.
22
INSPECTION
It is important that the three types of sling inspection should be utilized when a
sling has been purchased. The three types of inspection are:
INITIAL INSPECTION
Before any new or repaired sling is placed in service it shall be inspected to insure that the correct
sling is being used as well as to determine that the sling meets the requirements of the specification.
FREQUENT INSPECTION
This inspection should be made by the person handling the sling each time the sling is used.
PERIODIC INSPECTION
This inspection shall be conducted by designated personnel. Periodic inspection should
be conducted at least annually.
Remove the sling from service is any of the following is visible:
Cuts on the Face Holes, tares, snags Capacity tag is signs of excessive
of the webbing crushed webbing missing or illegible abrasive wear
OR
Sling shows signs of melting, charring or chemical damage
End fittings are excessively corroded, distorted, cracked or broken
Broken or worn threads in the stitch patterns
Knots in any part of the sling
Any other visible damage which causes doubt as to its strength
33
WEB SLINGS
TYPE 1 TRIANGLE - CHOKER
Type 1 (TC) slings have a steel triangle one end and a steel
choker on the other end. This sling can be used in vertical,
choker or basket hitches. The triangle fits easily through the
choker to provide a smooth, even choke.
SINGLE PLY DOUBLE PLY

STOCK WIDTH VERTICAL CHOKER BASKET STOCK WIDTH VERTICAL CHOKER BASKET
CODE NO. INCHES POUNDS POUNDS POUNDS CODE NO. INCHES POUNDS POUNDS POUNDS
TC1-902 2 3,200 2,400 6,400 TC2-902 2 6,400 4,800 12,800
TC1-903 3 4,800 3,600 9,600 TC2-903 3 8,800 6,600 17,600
TC1-904 4 6,400 4,800 12,800 TC2-904 4 11,500 8,600 23,000
TC1-906 6 9,600 7,200 19,200 TC2-906 6 16,500 12,400 33,000
TC1-908 8 12,800 9,600 25,600 TC2-908 8 22,000 16,500 44,000
TC1-910 10 16,000 12,000 32,000 TC2-910 10 24,000 18,000 48,000
TC1-912 12 19,200 14,400 38,400 TC2-912 12 28,800 21,600 57,600
WARNING MAXIMUM RATED CAPACITIES FOR NEW SLINGS. DO NOT EXCEED
TYPE 2 TRIANGLE - TRIANGLE
Type 2 (TT) slings have a steel triangle fitting on each

end. This type of sling can only be used in vertical and
basket hitches. These slings cannot be used in a choker
hitch.

STOCK WIDTH VERTICAL BASKET STOCK WIDTH VERTICAL BASKET
CODE NO. INCHES POUNDS POUNDS CODE NO. INCHES POUNDS POUNDS
TT1-902 2 3,200 6,400 TT2-902 2 6,400 12,800
TT1-903 3 4,800 9,600 TT2-903 3 8,800 17,600
TT1-904 4 6,400 12,800 TT2-904 4 11,500 23,000
TT1-906 6 9,600 19,200 TT2-906 6 16,500 33,000
TT1-908 8 12,800 25,600 TT2-908 8 22,000 44,000
TT1-910 10 16,000 32,000 TT2-910 10 24,000 48,000
TT1-912 12 19,200 38,400 TT2-912 12 28,800 57,600
44
WEB SLINGS
TYPE 3 & 4 - EYE & EYE
Type 3 (EE) straight eye & eye slings can be used in a vertical,
choker or basket hitch. These slings have a straight eye at each end
that makes it easier to remove them after the load is in place.
Tapered eyes are supplied on slings with a web width of 3" or larger.
Eye & eye slings will be supplied with T-3 eyes unless otherwise
specified.
Type 4 (EE) twisted eye & eye slings are similar to Type 3 slings
except the eyes are turned 90 degrees to the sling body. This
allows for a smoother choker hitch and a better fit in a basket
hitch. Tapered eyes are supplied on slings with a web width of 3"
or larger.

EE1-901 1 1,600 1.200 3,200 EE2-901 1 3,200 2,400 6,400
EE1-902 2 3,200 2,400 6,400 EE2-902 2 6,400 4,800 12,800
EE1-903 3 4,800 3,600 9,600 EE2-903 3 8,800 6,600 17,600
EE1-904 4 6,400 4,800 12,800 EE2-904 4 11,500 8,600 23,000
EE1-905 5 8,000 6,000 16,000 EE2-905 5 13,700 10,300 27,400
EE1-906 6 9,600 7,200 19,200 EE2-906 6 16,500 12,400 33,000
EE1-908 8 12,800 9,600 25,600 EE2-908 8 22,000 16,500 44,000
EE1-910 10 16,000 12,000 32,000 EE2-910 10 24,000 18,000 48,000
EE1-912 12 19,200 14,400 38,400 EE2-912 12 28,800 21,600 57,600
TYPE 5 Type 5 (EN) endless slings the webbing is overlapped to form

a continuous endless sling. The wear points on these slings
can be rotated to increase sling life. This type of sling can be
used in a vertical, choker or basket hitch.

EN1-901 1 3,200 2,550 6,400 EN2-901 1 6,400 5,100 12,800
EN1-902 2 6,400 5,100 12,800 EN2-902 2 12,400 9,900 24,800
EN1-903 3 9,400 7,050 18,800 EN2-903 3 17,600 13,200 35,200
EN1-904 4 12,400 9,300 24,800 EN2-904 4 22,000 17,600 44,000
EN1-905 5 15,000 12,000 30,000 EN2-905 5 27,500 22,000 55,000
EN1-906 6 18,600 14,000 37,200 EN2-906 6 33,000 24,800 66,000
EN1-908 8 22,000 17,600 44,000 EN2-908 8 40,000 32,000 80,000
EN1-910 10 25,500 20,400 51,000 EN2-910 10 47,000 37,600 94,000
EN1-912 12 28,200 22,550 56,400 EN2-912 12 50,000 40,000 100,000
55
WEB SLINGS
TYPE 6 RETURN EYE SLING
Type 6 (RE) return eye slings have protective webbing sewn
on the body to provide a long lasting flexible and wear-
resistant sling. These slings can be used in a vertical, choker
or basket hitch.

RE1-902 2 3,100 2,300 6,200 RE2-902 2 6,100 4,500 12,200
RE1-904 4 6,000 4,500 12,000 RE2-904 4 12,000 9,000 24,000
RE1-906 6 8,600 6,450 17,200 RE2-906 6 16,300 12,200 32,600
TYPE 7 EYE & EYE

These slings are designed for occasional or light duty lifting
applications. They can be used in a vertical, choker & bas-
ket hitch. Available in 1î & 1.75î only.

EE1-601 1 1,100 880 2,200 EE2-601 1 2,200 1,650 4,400
EE1-675 1-3/4î 1,900 1,425 3,800 EE2-675 1-3/4î 3,800 2,850 7,600
TYPE 7 ENDLESS
EN1-601 1 2,200 1,750 4,400 EN2-601 1 4,400 3,500 8,800
EN1-675 1-3/4î 3,800 3,050 7,600 EN2-675 1-3/4î 7,700 6,100 15,400
WIDE LIFT CARGO SLINGS

Wide lift slings provide maximum weight distribution of the
load for those extra wide lifts. These slings have
tapered eyes but can only be used in a basket hitch.

STOCK WIDTH BASKET EYE EYE STOCK WIDTH BASKET EYE EYE
CODE NO. INCHES POUNDS LENGTH WIDTH CODE NO. INCHES POUNDS LENGTH WIDTH
WL1-906 6 18,000 9" 1.5" WL2-906 6 34,000 9" 1.5"
WL1-908 8 24,000 12" 2" WL2-908 8 44,000 12" 2"
WL1-910 10 30,000 15" 2.5" WL2-910 10 55,000 15" 2.5"
WL1-912 12 35,200 18" 3" WL2-912 12 65,000 18" 3"
WL1-916 16 44,000 24" 4" WL2-916 16 80,000 24" 4"
WL1-920 20 51,000 30" 5" WL2-920 20 94,000 30" 5"
WL1-924 24 56,400 36" 6" WL2-924 24 100,000 36" 6"
66
WEB SLINGS
Three and four ply slings are only available in Type 3 or 4.
They can be used in a vertical, choker and basket hitch. The
eyes are tapered on sling widthís of 3î or greater. Type 3 is
standard. Type 4 can be supplied upon request.
THREE & FOUR PLY SLINGS
THREE PLY FOUR PLY
EE3-901 1 4,100 3,300 8,200 EE4-901 1 5,000 4,000 10,000
EE3-902 2 8,300 6,600 16,600 EE4-902 2 10,000 8,000 20,000
EE3-903 3 12,500 10,000 25,000 EE4-903 3 14,900 11,900 29,800
EE3-904 4 16,000 12,800 32,000 EE4-904 4 19,800 15,800 39,600
EE3-905 5 19,200 15,400 38,400 EE4-905 5 24,800 19,800 49,600
EE3-906 6 23,000 18,400 46,000 EE4-906 6 29,800 23,800 59,600
EE3-908 8 30,700 24,500 61,400 EE4-908 8 39,700 31,700 79,400
EE3-910 10 36,800 29,400 73,600 EE4-910 10 49,600 39,600 99,200
EE3-912 12 44,000 35,200 88,000 EE4-912 12 59,500 47,600 119,000
BRIDLE LEG SLINGS

SHH DOH TOH QOH
Special purpose slings with
various combinations of
hardware and loops. Available in
Single leg and multiple leg
combinations. Available in nylon
and polyester.
SINGLE LEG
STOCK LEG RATED CAPACITY (LBS.)*
NUMBER WIDTH PLY VERTICAL 60 45 30
EE1-901 SOH 1" 1 1600 lbs - - -
EE2-901 SOH 1" 2 3200 lbs - - -
EE1-902 SOH 2" 1 3200 lbs - - -
EE2-902 SOH 2" 2 6400 lbs - - -
TWO LEGGED
EE1-901 DOH 1" 1 - 2720 lbs 2240 lbs 1600 lbs
EE2-901 DOH 1" 2 - 5440 lbs 4480 lbs 3200 lbs
EE1-902 DOH 2" 1 - 5440 lbs 4480 lbs 3200 lbs
EE2-902 DOH 2" 2 - 10880 lbs 8960 lbs 6400 lbs
THREE LEGGED
EE1-901 TOH 1" 1 - 4160 lbs 3360 lbs 2400 lbs
EE2-901 TOH 1" 2 - 8320 lbs 6720 lbs 4800 lbs
EE1-902 TOH 2" 1 - 8320 lbs 6720 lbs 4800 lbs
EE2-902 TOH 2" 2 - 16640 lbs 13440 lbs 9600 lbs
FOUR LEGGED
EE1-901 QOH 1" 1 - 4160 lbs 3360 lbs 2400 lbs
EE2-901 QOH 1" 2 - 8320 lbs 6720 lbs 4800 lbs
EE1-902 QOH 2" 1 - 8320 lbs 6720 lbs 4800 lbs
EE2-902 QOH 2" 2 - 16640 lbs 13440 lbs 9600 lbs
77
WEB SLINGS
MARINE SLINGS
Nylon Marine slings (MS) are lightweight and easy to use. They will not scratch or
abuse the most delicate hull.
EXTRA EYES are available in QUICK DISCONNECTS allow for

tapered fabric or for use with easy removal and installation of
hardware. Allows a single sling to slings. Protective flap included.
adjust to different overall lengths.
KEEL PAD is fastened to the sling LEAD WEIGHTS keeps slings

at the centre fo protect the sling from under water. Allows easier
wear at the greatest load point. positioning of slings under boat.

STOCK WIDTH BASKET STOCK WIDTH BASKET
CODE NO. INCHES POUNDS CODE NO. INCHES POUNDS
MS1-903 3 9,600 MS2-903 3 17,600
MS1-904 4 12,800 MS2-904 4 23,000
MS1-906 6 19,200 MS2-906 6 33,000
MS1-908 8 25,600 MS2-908 8 44,000
MS1-910 10 32,000 MS2-910 10 48,000
MS1-912 12 38,400 MS2-912 12 57,600
GLASS SLINGS Glass Lifting Slings can be custom made to fit any size glass pack or crate. The
slings are fully lined with Rubber on the inside to protect the sling from the sharp
edges.
SINGLE PLY
STOCK LENGTH HEIGHT VERTICAL
CODE NO. INCHES RANGE POUNDS
GS1-078 78" 36" - 54" 12,400
GS1-108 108" 60" - 84" 12,400
GS1-124 124" 72" - 100" 12,400
TRANSFORMER SLINGS
Transformer slings are made to move transformers into place. They are made with
an endless nylon sling as the link, and 1-3/4" elastic web to ensure the eyes stay into
the lifting points.
DOUBLE PLY
STOCK WIDTH LEG LENGTH W.L.L 60
CODE NO. INCHES INCHES SPREAD Degrees
TS2-015 1-3/4" 15" 15" 2,800
TS2-020S 1-3/4" 20" 20" 2,800
TS2-020L 1-3/4" 20" 20" 2,800
TS2-030 1-3/4" 30" 30" 2,800
88
CARGO RESTRAINT STRAPS
RATCHET STRAPS
Ratchet straps can be customized to any length, although the standard length is 30ft.
RSWH
RATCHET STRAPS
W.L.L.
PART NO. WIDTH END HARDWARE POUNDS
RSWH1 1" Wire Hook 1,100 RSCA
RSWH2 2" Wire Hook 3,300
RSFH2 2" Flat Hook 3,300
RSEF2 2" E Fitting 1,500 RSWH
RSCA2 2" Chain Assembly 3,300
RSEN2 2" Endless 3,300
RSWH3 3" Wire Hook 5,000 RSFH
RSCA3 3" Chain Assembly 5,000
RSCA4 4" Chain Assembly 5,400 RSEN
RSCA
WARNING MAXIMUM RATED CAPACITIES FOR NEW STRAPS. DO NOT EXCEED
WINCH STRAPS
Winch straps can be customized to any length, although the standard length is 30ft.
WSWH
WINCH STRAPS
W.L.L.
PART NO. WIDTH END HARDWARE POUNDS
WSWH2 2" Wire Hook 3,300 WSDR
WSFH2 2" Flat Hook 3,300
WSCA2 2" Chain Assembly 3,300
WSWH3 3" Wire Hook 5,000
WSFH3 3" Flat Hook 5,000 WSCA
WSCA3 3" Chain Assembly 5,000
WSDR3 3" Dee Ring 5,000
WSFH4 4" Flat Hook 5,000
WSCA4 4" Chain Assembly 5,400 WSFH
WARNING MAXIMUM RATED CAPACITIES FOR NEW STRAPS. DO NOT EXCEED
99
CARGO RESTRAINT STRAPS
HARDWARE
1" Cam 2" Cam 2" Dee 3" or 4" Flat Wire
Buckle Buckle Ring Dee Ring Hook Hook
Snap Long Twisted Vinyl E Fitting Chain Assembly

Hook Snap Hook Snap Hook S Hook
WEB NETS
Customized Web Nets available to fit customer needs.
Order web nets by total outside dimensions, webbing
Width, mesh size, and rated capacities.
DRUM SLING TIRE TIE DOWN

Drum sling safely
lifts plastic and Fits wheels from
steel drums up to 15" - 20"
1000 lbs W.L.L. 1500 lbs
WINCHES CORNER PROTECTORS

Winches are used for Corner protectors are made to protect
securing cargo on both cargo and strap.
flatbed trailers.
Available: Sliding Webbing Winch

Weld on Webbing Winch
Storable Webbing Winch Metal Corner Plastic Corner
Protector Protector
10
10
10
ROUND SLINGS
POLYESTER ROUND SLINGS
APPROX. APPROX.
CODE COLOUR VERTICAL CHOKER 90° 30° 45° DIA. WEIGHT/FT.
NUMBER BASKET BASKET BASKET INCHES IN POUNDS
EN 30 Purple 3,000 2,400 6,000 5,200 4,200 .75 .25
EN 40 Black 4,000 3,200 8,000 6,900 5,600 .80 .35
EN 60 Green 6,000 4,800 12,000 10,300 8,400 .90 .40
EN 90 Yellow 9,000 7,200 18,000 15,500 12,600 1.00 .50
EN 120 Tan 12,000 9,600 24,000 20,600 16,800 1.25 .75
EN 140 Red 14,000 11,200 28,000 24,100 19,600 1.30 .85
EN 170 Orange 17,000 13,600 34,000 29,300 23,800 1.60 .95
EN 230 Blue 23,000 18,400 46,000 39,500 32,200 1.65 1.25
EN 260 Orange 26,000 20,800 52,000 44,700 36,400 1.75 1.45
EN 320 Grey 32,000 25,600 64,000 55,000 44,800 2.15 1.75
EN 400 Orange 40,000 32,000 80,000 68,800 56,000 2.45 2.25
EN 540 Brown 54,000 43,200 108,000 92,900 75,600 3.00 2.75

Olive
EN 680 Green 68,000 54,400 136,000 117,000 95,200 3.25 3.60
EN 900 Black 90,000 72,000 180,000 155,000 126,000 3.75 4.10
Rated Capacities in Pounds

11
11
11
ROUND SLINGS
SUPER SLINGER ROUND SLINGS

SUPER SLINGER are high performance slings. The sling is covered with a seamless double cover
nylon jacket to provide an extremely low elongation, flexible and light weight lifting sling.
APPROX. APPROX.
CODE COLOUR VERTICAL CHOKER 90° WEIGHT/FT. WIDTH
NUMBER BASKET IN POUNDS INCHES
SS-200 Black 20,000 16,000 40,000 .55 3
SS-250 Black 25,000 20,000 50,000 .65 4
SS-300 Black 30,000 24,000 60,000 .80 4
SS-400 Black 40,000 32,000 80,000 1.10 5
SS-500 Black 50,000 40,000 100,000 1.50 5
SS-600 Black 60,000 48,000 120,000 1.60 5
SS-700 Black 70,000 56,000 140,000 1.65 6
SS-850 Black 85,000 68,000 170,000 1.85 6
SS-1000 SUPER SLINGER

Black 100,000 80,000 FEATURES
200,000 2.20 6
SS-1250 Black 125,000 100,000 150,000 3.00 8
SS-1500 Black 150,000 120,000 300,000 3.35 8
SS-1750 Black 175,000 140,000 350,000 4.00 10
SS-2000 Black 200,000 160,000 400,000 4.35 10
Super Slinger Features

High strength to weight ratio Low elongation 1%
Easier and faster to rig than wire or chain slings Requires less personnel to do a lift
Easy storage and transportation Repairable
Excellent chemical resistance
12
12
12
ROUND SLINGS
Round Sling Construction

Apex Round Slings are constructed from a multiple of high tenacity
polyester yarns in an endless or continuous loop. These load bearing yarns
are protected by two woven polyester jackets. The polyester jackets act as a
buffer between the load and the polyester yarn.
Each sling has a tag permanently attached. This tag contains load capacities
and basic safeguard principles for safer lifting.
Sleeves are to be used when lifting sharp edged loads for even better
resistance to cutting. The sleeve is sewn around the cover of the round sling so that it can be positioned to
the area where it is required.
Round Sling Features

The most flexible sling available. This sling conforms to the load extremely well, and provides the
best choker hold.
Hook and load contact points can be continually rotated to extend the service life of the sling.
Longer sling life means cost reduction in sling purchases.
The load bearing fiber never comes into contact with the load. There is no wear to the inner fibers,
provided the protective cover remains intact.
Protection to the load from sling damage.
Seamless cover, no edges to wear out.
Wide variety of sling lengths and load capacities.
Adapts to all types, sizes, and load configurations.
Lightweight, easy to rig, store, and clean.
Excellent resistance to ultra-violet light, rot, and mildew.
No loss of strength in water.
Only 3% elongation.
Maximum temperature exposure 180°F.
Reduces the need for wear pads.
No metal parts to rust.
13
13
13
Grade 100 Forged Grade 80
Spectrographic Analysis:
To assure the proper metallurgy content of all raw materials.
Magnaflux Crack Detection:
All forged chain components are each individually magnafluxed
to detect any irregularities after heat treatment.
Eddy Current Detection:
All load pins are 100% individually inspected and tested after
heat treatment.
Ultrasonic Detection:
Forged Hooks or Links size 22mm or larger, have ultrasonic
detection to avoid any internal cracking. Certificate available
upon request.
Manufacturing Proof Load Test:
All chain and components are proof load tested at 2.5 times the
working load limits with resultant permanent deformation within
1%.
Dynamic Fatigue Testing:
Batch samples of chain and components are Dynamic Fatigue
Tested at 1.5 times the working load limit for 20,000 cycles.
Ultimate breaking load test:
Batch samples of Chain and Components are break load tested in a static tensile testing machine to ultimate
failure. The minimum ultimate break force is equal to the Working Load Limit times the safety factor, (a minimum
of 4 times the working load and up to 6 times based on the item).
14
14
14
Worldwide Quality Type Approval and Certificates:
All YOKE Products meet or exceed ASME B30 Requirements
15
15
15
Grade 80 and Grade 100 Chain Slings made to order!
Simply call and tell us what size, type and grade you are looking for and we will get back to you right away with a competitive
price. Chain slings are fully certified and can be proof tested upon request. See Chain sling charts below for Working Load Limits.
First symbol (basic type):

S - Single chain sling
C - Single choker chain sling with a standard end link on each end, no hooks
D - Double branch chain sling
T - Triple branch chain sling
Q - Quadruple branch chain sling
A - Proceeds symbol if shortening clutches are used
Second symbol (type of master link or end link):

O - Oblong master link of standard dimensions
P - Pear shaped master link
Third symbol (type of hook):

S - Sling hook
G - Grab hook
F - Foundry hook
Grade 80 Chain Sling Working Load Limits Rated in pounds

Single Leg lbs Two Leg lbs Three and Four Leg lbs
Chain Grade 80 Size
inch mm 90° 60° 45° 30° 60° 45° 30°

7/32 6 2100 3600 3000 2500 6500 5300 3750
1/4~9/32 7 3500 6100 4900 3500 9100 7400 5200
5/16 8 4500 7800 6400 4500 11700 9500 6800
3/8 10 7100 12300 10000 7100 18400 15100 10600
1/2 13 12000 20800 17000 12000 31200 25500 18000
5/8 16 18100 31300 25600 18100 47000 38400 27100
3/4 20 28300 49000 40000 28300 73500 60000 42400
7/8 22 34200 59200 48400 34200 88900 72500 51300
1 26 47700 82600 67400 47700 123900 101200 71500
1-1/4 32 72300 125200 102200 72300 187800 153400 108400

Chain Grade 100 Size
inch mm 90° 60° 45° 30° 60° 45° 30°

7/32 6 2700 4700 3800 2700 7000 5700 4000
1/4~9/32 7 4300 7400 6100 4300 11200 9100 6400
5/16 8 5700 9900 8100 5700 14800 12100 8500
3/8 10 8800 15200 12400 8800 22900 18700 13200
1/2 13 15000 26000 21200 15000 39000 31800 22500
5/8 16 22600 39100 32000 22600 58700 47900 33900
3/4 20 35300 61100 49900 35300 91700 74900 52950
7/8 22 42700 74000 60400 42700 110900 90600 64000
16
16
16
CHAIN INSPECTION REPORT
Date INSPECTED BY: APEX CHAIN & CABLE Inc. PHN: 519-751-8085
6/3/2014 FAX: 519-751-8005
The following items were inspected in accordance with the annual inspection requirement of Regulation 851 of the Ontario Occupational Health and Safety Act. (OHSA)
The inspection was done in accordance with the recommendations of ASME Standards B30.20 Below-the-Hook Lifting Devices, B30.26 Rigging Hardware, B30.9 Slings, B30.10 Hooks and B30.16 Hoists.
DAMAGE
W.L.L. RECOMMENDATIONS Date

Location Serial Number Lbs. Type Size Reach Returned Repair PO# REPAIR STATUS
ACCEPT
REPAIR
SCRAP
Mast Link
Couplings
Legs
Hooks
ID TAG
Date Tag
Other
я
я
я
я
я
я
я
я
я
я
я
я
17
17
я
я
я
я
я
я
я
я
я
я
я
я
я
я
я
я
я
я
я
я
я
я
я
Connecting Link Grade 80 (4:1 WLL)
Grade 80 Spare Pin & Bushing Dimensions (inch) N.W.
WLL Part Number
Chain Part Number K A D B Lbs
9/32 4,500 28-7-8CLP 2.25 0.79 0.35 0.89 0.4 28-7-8CL
3/8 7,100 28-10CLP 2.68 1.02 0.50 1.06 0.6 28-10CL
1/2 12,000 28-13CLP 3.58 1.19 0.62 1.42 1.5 28-13CL
5/8 18,100 28-16CLP 3.98 1.42 0.75 1.54 2.4 28-16CL
3/4 28,300 28-18-20CLP 4.62 1.65 0.91 1.73 3.7 28-18-20CL
7/8 34,200 28-22CLP 5.98 1.93 0.94 2.32 6.6 28-22CL
1 47,700 28-26CLP 6.38 2.17 1.19 2.44 10.1 28-26CL
1-1/4 72,300 28-32CLP 7.99 2.72 1.42 3.11 18.9 28-32CL
Omega Link Grade 80 (4:1 WLL)

Grade 80 Spare Pin Kit Dimensions (inch) N.W.
WLL Part Number
Chain Part Number K D T P kg
1/4-5/16 4,500 28-7-8LPK 2.09 1.06 0.44 0.35 0.4 28-7-8MMOL
3/8 7,100 28-10LPK 2.60 1.26 0.59 0.47 0.8 28-10MMOL
1/2 12,000 28-13LPK 3.31 1.65 0.67 0.62 2.2 28-13MMOL
5/8 18,100 28-16LPK 4.06 1.96 0.89 0.71 3.0 28-16MMOL
Hook, Clevis Claw, Shortening Clutch, Grade 80 (4:1 WLL)

WLL Part Number
Chain Part Number A,B C D E F Lbs
9/32 4,500 28-7-8LPK 0.34 0.39 0.35 0.63 2.44 0.8 28-7-8CCH
3/8 7,100 28-10LPK 0.49 0.55 0.47 0.98 3.43 2.0 28-10CCH
1/2 12,000 28-13LPK 0.65 0.67 0.59 1.26 4.53 4.2 28-13CCH
5/8 18,100 28-16LPK 0.81 0.75 0.75 1.54 5.63 6.9 28-16CCH
3/4 28,300 28-18-20LPK 0.85 0.91 0.87 1.81 5.98 13.6 28-18-20CCH
18
18
18
Hook, Clevis Grab Grade 80 (4:1 WLL)
WLL Part Number
Chain Part Number P A F K H L Lbs
1/4-5/16 4,500 28-7-8LPK 0.39 0.35 1.18 2.17 0.98 3.66 0.6 28-7-8CGH
3/8 7,100 28-10LPK 0.51 0.47 1.61 3.03 1.38 5.04 1.7 28-10CGH
1/2 12,000 28-13LPK 0.63 0.59 2.09 3.82 1.65 5.98 3.3 28-13CGH
5/8 18,100 28-16LPK 0.79 0.67 2.28 4.02 1.77 7.09 6.3 28-16CGH
3/4 28,300 28-18-20LPK 0.98 0.91 3.86 4.88 2.13 8.54 11.0 28-18-20CGH
Hook, Eye Grab Grade 80 (4:1 WLL)

Grade 80 Dimensions (inch) N.W.
WLL Part Number
Chain P A G K F Lbs
7/8 34,200 1.06 1.50 1.02 6.18 4.33 18.0 28-22EGH
1 47,700 1.14 1.61 1.26 7.36 3.94 21.5 28-26EGH
1-1/4 72,300 1.46 2.24 1.57 9.06 3.54 42.7 28-32EGH
Hook Clevis Sling c/w Latch Gr-8 (4:1 WLL)

Grade 80 Spare Pin kit Spare Latch Kit Dimensions (inch) N.W.
WLL Part Number
Chain Part # Part # K P1 T H Lbs
9/32 4,500 28-7-8LPK 28-7-8LK 3.74 1.18 0.75 0.91 1.1 28-7-8CSH
3/8 7,100 28-10LPK 28-10LK 4.72 1.42 0.91 1.22 2.2 28-10CSH
1/2 12,000 28-13LPK 28-13LK 5.79 1.73 1.10 1.50 4.6 28-13CSH
5/8 18,100 28-16LPK 28-16LK 6.65 1.81 1.30 1.73 8.1 28-16CSH
3/4 28,300 28-18-20LPK 28-18-20LK 7.48 2.36 1.97 2.01 13.2 28-18-20CSH
8
19
19
19
Hook, Eye Sling Grade 80 (4:1 WLL)
Grade 80 Latch Kit Dimensions (inch) N.W.
WLL Part Number
Chain Part Number K P1 A D T H Lbs
5/8 18,100 28-16LK 7.20 1.85 1.97 0.87 1.29 1.85 6.9 28-16ESH
7/8 34,200 28-22LK 9.45 2.75 1.97 1.26 1.97 2.91 18.7 28-22ESH
1 47,700 28-26LK 10.63 3.15 2.60 1.34 2.36 3.15 27.9 28-26ESH
1-1/4 72,300 28-32LK 12.60 3.54 3.50 1.46 2.56 3.58 36.3 28-32ESH
Hook, Clevis Self-locking Grade 80 (4:1 WLL)

Grade 80 Trigger Kit Dimensions (inch) N.W.
WLL Part Number
Chain Part Number K P T H Lbs
1/4-5/16 4,500 28-7-8TK 4.69 1.34 0.75 0.94 1.7 28-7-8SLCH
3/8 7,100 28-10TK 5.63 1.73 0.94 1.22 3.3 28-10SLCH
1/2 12,000 28-13TK 7.05 2.05 1.06 1.57 6.1 28-13SLCH
5/8 18,100 28-16TK 8.35 2.36 1.42 2.09 12.3 28-16SLCH
3/4 28,300 28-18-20TK 12.56 2.67 1.93 2.80 16.5 28-18-20SLCH
Hook, Self-locking EYE Grade 80 (4:1 WLL)

Grade 80 Trigger Kit Dimensions (mm) N.W.
WLL Part Number
Chain Part Number K P A D T H Lbs
1/4-5/16 4,500 28-7-8TK 5.35 1.34 0.98 0.44 0.79 0.94 1.7 28-7-8SLEH
3/8 7,100 28-10TK 6.57 1.73 1.26 0.51 1.02 1.19 3.0 28-10SLEH
1/2 12,000 28-13TK 8.15 2.05 1.56 0.62 1.19 1.50 5.9 28-13SLEH
5/8 18,100 28-16TK 9.92 2.36 2.05 0.83 1.56 1.91 12.3 28-16SLEH
3/4 28,300 28-18-20TK 11.10 3.54 2.52 0.91 1.91 1.96 18.7 28-18-20SLEH
20
20
20
Hook, Swivel Self-Locking Grade-80 (4:1 WLL)
Trigger Kit Dimensions (inch) N.W.
Gr 80 WLL Part Number
Part # K P B A D T H Lbs
1/4-5/16 4,500 28-7-8TK 5.94 1.38 0.79 1.42 0.51 0.79 1.02 2.4 28-7-8SSLH
3/8 7,100 28-10TK 6.75 1.73 1.06 1.63 0.62 1.02 1.34 4.4 28-10SSLH
1/2 12,000 28-13TK 8.23 2.05 0.94 1.81 0.83 1.19 1.56 8.8 28-13SSLH
5/8 18,100 28-16TK 10.43 2.36 1.56 2.36 0.91 1.56 2.17 14.9 28-16SSLH
3/4 28,300 28-18-20TK 14.09 3.54 3.23 2.91 0.98 1.91 2.56 25.5 28-18-20SSLH
7/8 34,200 28-22TK 16.93 3.15 2.48 3.15 1.14 1.93 2.48 35.2 28-22SSLH
1 47,700 28-26TK 18.90 3.90 3.78 4.13 1.26 2.20 2.72 47.4 28-26SSLH
Eye Foundry Hook (4:1 WLL)

Working Grade 80 Dimensions (inch) N.W.
Part Number
Load Limit Chain K P A D T H Lbs
7,100 3/8 5.91 2.91 1.22 0.59 0.96 1.34 2.6 28-3/8FEH
12,000 1/2 7.09 3.46 1.57 0.79 1.34 1.65 5.0 28-1/2FEH
18,100 5/8 8.46 3.86 1.93 0.94 1.69 1.97 8.8 28-5/8FEH
28,300 3/4 9.76 4.41 2.36 1.10 1.81 2.24 13.2 28-3/4FEH
Hook Eye Hoist Grade-80 (5:1 WLL)

WLL Latch Kit Dimensions (inch) N.W.
Part Number
tonnes Part Number P1 A T H K D Lbs
2 28-2TLK 0.98 1.14 0.79 1.02 4.21 1.02 1.4 28-2TEHH
3 28-3TLK 1.14 1.26 0.87 1.14 4.80 1.14 1.9 28-3TEHH
5 28-5TLK 1.50 1.57 1.18 1.46 5.91 1.50 4.2 28-5TEHH
7 28-7TLK 1.73 2.00 1.42 1.85 7.52 1.93 8.3 28-7TEHH
21
21
Shortening Clutch with alf Link Grade 80 - design factor 4:1 - Cert supplied on request
Grade 80 Dimensions (inch) Wt.
WLL lbs Part Number
Chain A C D E F H G K Lbs
9/32 4,500 0.47 0.79 0.39 0.91 2.76 0.89 0.35 5.04 1.5 28-078-7-8
3/8 7,100 0.51 1.02 0.47 1.14 3.43 1.06 0.50 6.06 2.9 28-078-10
1/2 12,000 0.59 1.30 0.63 1.46 4.53 1.38 0.62 7.99 6.2 28-078-13
Shank Coupling Grade 80 - design factor 4:1 - Cert supplied on request

Grade 80 Dimensions (inch) Wt.
WLL lbs Part Number
Chain D d min ** L1 L2 Lbs
3/8 7,100 1.38 0.63 2.76 1.26 1.5 28-10CS
Code " KP "
A For
Grade 80
inch A K T H Lbs
8-022-06 1.12 7/32 0.24 6.14 1.14 0.59 0.75 1.8
8-022-07 2.0 1/4~5/16 0.35 7.40 1.34 0.79 0.94 2.9
K
8-022-10 3.15 3/8 0.43 8.46 1.77 1.02 1.19 4.9
8-022-13 5.3 1/2 0.55 10.83 2.13 1.19 1.57 9.9
P P 8-022-16 8.0 5/8 0.71 12.72 2.44 1.42 1.93 17.4
8-022-20 12.5 3/4 0.83 16.45 3.54 1.91 2.36 27.6
H
T
22
22
22
Container Hooks – Design factor 4:1 proof tested and certified - Cert supplied on request
Dimensions (inch) Wt Pcs
WLL / lbs Type Part Number
K E F T G H lbs Box
12.5 te Left 45 6.81 2.76 1.81 0.98 2.95 1.89 8.6 12 28-8-06745LT
12.5 te Right 45 6.81 2.76 1.81 0.98 2.95 1.89 8.6 12 28-8-06745RH
Weld on Bucket Hook – (5:1 design factor check legislative requirement) - Cert supplied on request
Latch Kit Dimensions (inch) Weld
WLL Wt. Pcs Hook Part
Bead
tonne Price Part # A F H L M P T W lbs Box Number
“a”
3.0 27.22 28-3TWOHL 0.39 1.38 1.18 4.17 0.24 1.14 0.91 5.24 6mm 3.1 12 28-3TWOH
4.0 30.69 28-4TWOHL 0.47 1.65 1.54 4.41 0.28 1.22 1.14 5.59 7mm 4.4 8 28-4TWOH
5.0 34.63 28-5TWOHL 0.51 1.77 1.81 5.16 0.31 1.34 1.22 6.54 8mm 6.6 6 28-5TWOH
10.0 41.07 28-10TWOHL 0.55 2.20 2.36 6.69 0.35 1.97 1.73 8.70 9mm 13.9 6 28-10TWOH
Welding Instructions - The welding should only be carried out by qualified welder according to Standards, e.g. EN 287 or AWS.
Support material
- The support material ST 52-3.
- Prior to welding, the contact areas must be free from impurities, oil, paint, rust, scale, etc., for example by grinding. If the surface is
at all corroded, all rust must be completely removed from the weld area. Painted surface must be prepared in the same way.
- The steel support member must have a carbon content of no less than 0.25% and no more than 0.40%.
- The hook must be positioned that the weld is loaded only in shear. No bending moment can be permitted on weld seam.
- In ambient temperature of 10ºC and below, pre-heating of the weld area prior to welding must be carried out.
Seam welding
- The welds must be sufficiently strong to take the required loads.
- A minimum weld-seam width must be maintained to give adequate weld strength (see table)
- The gauging points on the supports guarantee the gap necessary for the root pass (approx. 3mm)
- Start both, the root pass and final weld pass from the centre of the support to be welded.
- Before starting the final weld pass, clean well the root pass to avoid inclusions.
- The complete welding operation must be carried out continuously so that the parts do not have time to cool.
MIG arc welding:
- Wire diameter 0.8 - 1.2 as per DIN 8559-SG 3.
- Important: do not weld in the open air during bad weather
Manual electric: Direct current supply welding:
- Electrodes according to EN ISO 2560-A - E 42 6 B 3 2, AWS A 5.5 : E 8018-G.
- Electrode: root pass & final weld pass, type E5154 B10 as per DIN 1913, used in accordance with the manufacturers.
Alternating current supply welding:
- Electrode as per DIN 1913, modified for alternating current use.
- HV welding and final weld pass, type E5155 B10.
23
23
23
Link Master YOKE 8-003
WLL 5:1 Chain Size Inside Inside Weight Standard 8-003
Size Dia.
Pounds 1-leg 2-leg length width lbs Part Number
7,000 1/2" 1/4~5/16 7/32 4.72 2.76 0.55 0.8 28-1/2"ML
9,000 5/8" 3/8 1/4~5/16 5.51 3.15 0.67 1.5 28-5/8"ML
12,300 3/4" 3/8 - 5.91 3.54 0.75 2.2 28-3/4"ML
14,000 7/8” 1/2 3/8 6.30 3.74 0.87 3.3 28-7/8”ML
24,360 1" 5/8 3/8 7.48 4.33 0.98 4.8 28-1"ML
30,000 1-1/8" 5/8 1/2 7.09 4.13 1.10 5.9 28-1-1/8"ML
36,000 1-1/4” 3/4 - 7.87 4.72 1.18 7.7 28-1-1/4”ML
42,000 1-3/8” 3/4 5/8 9.45 5.51 1.34 11.2 28-1-3/8”ML
54,300 1-1/2” 7/8 3/4 9.84 5.91 1.50 15.4 28-1-1/2”ML
85,000 1-3/4” 1-1/4 1 11.81 7.09 1.77 26.4 28-1-3/4”ML
102,600 2” 1-1/4 1 13.77 7.67 1.96 36.5 28-2”ML
145,000 2-1/4” - 1-1/4 16.14 8.66 2.28 57.2 28-2-1/4”ML
193,100 2-3/4” - - 19.29 10.43 2.75 100.0 28-2-3/4”ML
Enlarge Oblong Master Link Assembly . Code ''MFA''. Designed for use with chain & wire rope.
WLL(Lbs) WLL(Lbs) Grade 80
Dimensions (inch) N.W.
ß 0-45° ß 045°-60° chain (inch) Part Number
Lbs
4:1 5:1 4:1 5 : 1 3 or 4 Legs D IW IL d iw il
18,900 15,100 17,600 14,100 1/4-5/16 0.87 3.54 6.38 0.79 2.76 5.51 7.9 28-7-8MLA
31,900 25,500 23,300 18,700 3/8 1.10 4.33 7.87 0.87 2.76 5.51 12.1 28-3/8MLA
50,900 40,700 37,200 29,800 1/2 1.42 5.50 10.63 1.10 3.54 7.28 26.2 28-1/2MLA
63,900 51,100 47,100 37,700 5/8 1.57 6.10 11.02 1.26 4.33 7.87 36.1 28-5/8MLA
80,400 64,300 57,500 46,000 3/4 1.77 6.89 12.60 1.42 4.92 8.86 51.7 28-3/4MLA
99,600 79,700 73,600 58,900 7/8 1.97 7.68 13.78 1.57 5.12 10.24 71.1 28-7/8MLA
132,000 105,600 99,600 79,700 1 2.36 8.66 16.14 1.97 7.68 13.78 130.6 28-1MLA
186,700 149,300 132,000 105,600 1-1/4” 2.76 10.43 19.29 2.36 8.66 16.14 214.5 28-1-1/4MLA
Proof tested and certified
Weldless Sling Link Pear, Galvanized (5:1 WLL)

Inside Inside
Size WLL Weight Inside Width Width Price Part
(in) (lbs) (lbs) Length Small Large $ Number
End End
3/8 1800 0.13 2-1/4 3/4 1-1/2 3.38 6-3/8"PLG
1/2 2900 0.55 3 1 2 4.24 6-1/2"PLG
5/8 4200 1.10 3-3/4 1-1/4 2-1/2 7.02 6-5/8"PLG
3/4 6000 1.95 4-1/2 1-1/2 3 10.62 6-3/4"PLG
7/8 8300 2.78 5-1/4 1-3/4 3-1/2 17.60 6-7/8"PLG
1 10800 4.30 6 2 4 22.60 6-1"PLG
1 1/4 16750 8.50 7-3/4 2-1/2 5 45.83 6-1-1/4"PLG
24
24
Lifting Rings
DNV Master Links

CerƟĮed to DNV 2.7-1, type approval no. S-7732
For oīshore container liŌing and cold weather use with Charpy V-notch impact Value’s of > 42 Joule
At -20ȗC. All DNV links are specially heat treated aŌer proof tesƟng to minimize the risk of hydrogen
embriƩlement and stress corrosion cracking. Every link is batch coded for cerƟĮcate recogniƟon.
Master Links
Dimensions mm
Old Part Number WLL tonne
Type Mass kg/unit Part Number
Being replaced 5:1
Dia. Inside Length Inside Width
OML220DNV N/A 22 270 140 5.8 2.3 2-MA22ML
OML255DNV N/A 25 270 140 8.83 3.3 2-MA25ML
OML280DNV N/A 28 270 140 11.8 3.8 2-MA28ML
OML320DNV N/A 32 270 140 17.1 5.1 2-MA32ML
OML360DNV N/A 36 270 140 23.0 6.5 2-MA36ML
OML400DNV N/A 40 280 155 28.1 8.5 2-MA40ML
OML450DNV 28-1-3/4”ML 45 320 175 38.3 12.2 2-MA45ML
OML500DNV 28-2”ML 50 350 195 45.0 16.6 2-MA50ML
OML600DNV 28-2-1/4”ML 60 430 230 65.0 29.2 2-MA60ML
OML700DNV 28-2-3/4”ML 70 480 260 85.0 44.3 2-MA70ML
25
Lifting Rings
DNV Quad Assemblies

CerƟĮed to DNV 2.7-1, type approval no. S-7732
For oīshore container liŌing and cold weather use with Charpy V-notch impact Value’s of > 42 Joule
At -20ȗC. All DNV links are specially heat treated aŌer proof tesƟng to minimize the risk of hydrogen
embriƩlement and stress corrosion cracking. Every link is batch coded for cerƟĮcate recogniƟon.
Master Link - Quad Assemblies

Old Part Number Dimensions mm WLL tonne
Type Mass kg/unit Part Number
Being Replaced 5:1
D IL IW d il iw
OSA160DNV 28-7-8MLA 16 150 75 13 90 50 4.1 1.3 2-MA16QA
OSA220DNV 28-5/16MLA 22 270 140 16 150 75 5.8 3.8 2-MA23QA
OSA220SDNV 28-3/8MLA 22 162 90 20 140 70 8.83 3.6 2-MA22QAS
OSA255DNV N/A 25 270 140 20 140 70 8.83 5.3 2-MA25QA
OSA280DNV N/A 28 270 140 20 140 70 11.8 5.9 2-MA26QA
OSA280SDNV 28-1/2MLA 28 200 110 22 140 70 14.5 5.5 2-MA28QAS
OSA320DNV N/A 32 270 140 26 185 90 17.1 9.7 2-MA32QA
OSA360DNV 28-5/8MLA 36 270 140 28 190 100 23.0 11.9 2-MA36QA
OSA400DNV N/A 40 280 155 32 200 110 28.1 16.4 2-MA40QA
OSA450DNV 28-3/4MLA 45 320 175 36 225 125 38.3 23.5 2-MA45QA
OSA500DNV 28-7/8MLA 50 350 195 40 260 130 45.0 32.3 2-MA50QA
OSA600DNV 28-1MLA 60 410 220 50 350 195 65.0 63.9 2-MA60QA
OSA700DNV 28-1-1/4MLA 70 480 260 60 410 220 85 102.6 2-MA70QA
WLL 5:1 @ 45º in WLL 5:1 lbs WLL 5:1 lbs WLL 5:1 lbs WLL 4:1 lbs WLL 4:1 lbs WLL 4:1 lbs
Number Size mm ML/SL
tonne @ 60ȗ horiz. @ 45ȗ horiz. @ 30ȗ horiz. @ 60ȗ horiz. @ 45ȗ horiz. @ 30ȗ horiz.
2-MA16QA 16/13 4.1 11,070 9,040 6,390 13,830 11,300 7,990

2-MA23QA 22/16 5.8 15,660 12,780 9,040 19,570 15,980 11,300
2-MA22QAS 22/20 8.83 23,840 19,460 13,760 29,800 24,330 17,200
2-MA25QA 25/20 8.83 23,840 19,460 13,760 29,800 24,330 17,200
2-MA26QA 28/20 11.8 31,860 26,000 18,390 39,820 32,510 22,990
2-MA28QAS 28/22 14.5 39,150 31,960 22,600 48,930 39,950 28,250
2-MA32QA 32/26 17.1 46,170 37,700 26,650 57,710 47,120 33,320
2-MA36QA 36/28 23 62,100 50,700 35,850 77,620 63,380 44,810
2-MA40QA 40/32 28.1 75,870 61,950 43,800 94,840 77,430 54,750
2-MA45QA 45/36 38.3 103,400 84,430 59,700 129,260 105,540 74,630
2-MA50QA 50/40 45 121,500 99,200 70,150 151,880 124,000 87,680
2-MA60QA 60/50 65 175,500 143,300 101,320 219,380 179,120 126,660
2-MA70QA 70/60 85 229,500 187,400 132,500 286,880 234,240 165,630
26
Modular Coupling System
Insulated Blank Swivel * Half Coupling link * Master link *
Round Sling * Self-locking Hook * Shank *
Yoke’s interchangeable end connectors
Insulator Blank Swivel with multiple

Examples of end attachments
* - Stock inventory item
25
25
27
Yoke’s “Coupling Pin” System hook.
Yoke Round Sling Self Locking Hook is designed in a way to solve your synthetic end-fitting problems. The round sling self
locking hook presents the following benefits:
• The round shape is designed to provide great protection to your synthetic round sling on loading.
• Offer complete range of hooks from 1 ton to 21.2 ton
• Assembly is fast and easy with only a hammer required.
• The hook with self locking function meets real safety required.
26
26
28
YOKE ''BSI'' Insulated Swivels and Fittings
• The perfect system for universal coupling of components
to chain, wire rope and synthetic slings.
• Heavy hoisting with a strong but lightweight system. All
components are forged high alloy steel
compatible with forged chain and fittings.
• Assembly is fast and ready with only a hammer required.
• Individual swivels & components 100% proof load tested
to a minimum of 2.5 times the WLL.
• All ''BSI'' Swivels are individually tested during
manufacturing to assure insulating properties. A
insulated Test Certificate is packaged with each unit
shipped.
• YOKE ''BSI'' Insulated Swivels are designed with ball
bearing that fully swivel under load.
• Acquired certificate approved by BG German company.
• Individually tested to resist 1500 Volt DC with test
certificate
Insulated Blank Swivel (4:1 WLL) Pin and Sleeve Extra

Working Grade Dimensions (inch) N.W.
Load 80 Part Number
D L Lbs
Limit Chain
4,500 9/32 1.97 2.76 1.9 28-9/32BSI
7,100 3/8 2.44 3.39 2.6 28-3/8BSI
12,000 1/2 3.03 4.53 5.5 28-1/2BSI
18,100 5/8 3.70 5.28 9.7 28-5/8BSI
28,300 3/4 4.29 6.14 15.3 28-3/4BSI
Half Coupling Link (4:1 WLL) Pin & Sleeve Included

Working Grade Dimensions (inch) N.W. Part
Load 80 Lbs Number
Limit Chain K A D L
4,500 9/32 0.87 0.71 0.35 1.10 0.2 28-9/32CLH
7,100 3/8 1.02 0.98 0.47 1.30 0.4 28-3/8CLH
12,000 1/2 1.38 1.18 0.63 1.70 0.8 28-1/2CLH
18,100 5/8 1.61 1.42 0.79 2.00 1.5 28-5/8CLH
28,300 3/4 1.90 1.65 0.91 2.50 2.4 28-3/4CLH
Pin and Sleeve (adder for multifunction assemblies)

Working Length Dia. Of Length Dia of N. W.
Size Part Number
Load Limit Sleeve Sleeve Pin Pin Lbs.
4,500 1/4~5/16 0.47 0.51 1.97 0.24 0.04 28-7-8CLP
7,100 3/8 0.71 0.63 2.64 0.31 0.08 28-10CLP
12,000 1/2 0.83 0.71 3.23 0.39 0.15 28-13CLP
18,100 5/8 0.98 0.94 4.13 0.47 0.33 28-16CLP
28,300 3/4 1.14 1.18 4.57 0.59 0.57 28-18-20CLP
27
27
29
Half Coupling Link - Grade 80 - design factor 4:1 - Pin & Sleeve Included - Cert supplied on request
Grade 80 Working Dimensions (inch) Wt. Pcs
Part Number
Chain Load Limit A D K L Lbs Box
9/32 4,500 0.71 0.35 0.89 1.10 0.2 100 28-9/32CLH
3/8 7,100 0.98 0.50 1.06 1.30 0.4 100 28-3/8CLH
1/2 12,000 1.18 0.62 1.38 1.77 0.9 40 28-1/2CLH
5/8 18,100 1.42 0.75 1.51 1.97 1.3 25 28-5/8CLH
3/4 28,300 1.65 0.87 1.81 2.36 2.4 20 28-3/4CLH
Round sling Coupling – Grade 80 - design factor 4:1 - Cert supplied on request
Part Number
Chain Load Limit A B K W Lbs Box
9/32 4,500 0.71 0.94 1.30 1.57 0.4 60 28-9/32CRS
3/8 7,100 0.98 1.14 1.65 1.85 0.9 50 28-3/8CRS
1/2 12,000 1.18 1.38 2.01 2.09 1.5 25 28-1/2CRS
5/8 18,100 1.42 1.73 2.48 2.64 2.9 15 28-5/8CRS
3/4 28,300 1.65 2.05 2.87 3.15 4.6 10 28-3/4CRS
Pin & Sleeve extra see page 44
Web Sling Connector - design factor 4:1 - complete with half coupling link & pin - Cert supplied on request
This is a complete assembly already made up.
Part Number
Chain Load Limit A B D K W Lbs Box
7/8 34,200 1.93 2.32 0.94 7.36 4.92 16.3 2 28-016-22
1 47,700 2.17 2.44 1.19 8.23 5.91 25.3 2 28-016-26
1-1/4 72,300 2.72 3.11 1.42 10.98 7.48 40.6 1 28-016-32
28
28
30
Coupling Self Locking Hook – Grade 80 - design factor 4:1
Part Number
Chain Load Limit H K P T Lbs box
9/32 4,500 0.94 5.35 1.34 0.79 1.8 20 28-9/32CSLH
3/8 7,100 1.19 6.06 1.77 1.02 3.1 12 28-3/8CSLH
1/2 12,000 1.57 7.95 2.13 1.19 6.4 6 28-1/2CSLH
5/8 18,100 1.93 9.53 2.44 1.42 11.9 4 28-5/8CSLH
3/4 28,300 2.36 10.12 3.54 1.91 17.9 2 28-3/4CSLH
Coupling Master Link – Grade 80 - design factor 4:1

Part Number
Chain Load Limit A H K T W Lbs Box
9/32 4,500 0.59 0.59 3.94 0.59 1.97 0.7 45 28-9/32MLC
3/8 7,100 0.79 0.75 5.00 0.75 2.56 1.5 20 28-3/8MLC
1/2 12,000 0.98 0.87 5.71 0.91 2.83 2.2 15 28-1/2MLC
5/8 18,100 1.18 1.02 6.85 0.98 3.15 3.5 12 28-5/8MLC
3/4 28,300 1.42 1.42 7.95 1.22 4.09 6.6 5 28-3/4MLC
Flat Webbing Choker - Design Factor 4:1 proof tested and certified
Dimensions (inches) Wt.
WLL lbs Part Number
lbs
K P B A D W T H
4,400 5.51 1.73 0.94 3.19 0.55 3.15 1.57 1.73 4.6 28-031-02
29
29
31
Weld on Lifting Point - (5:1 design factor) - Cert supplied on request - Welding instructions included
WLL WLL Dimensions (inches) Weight Pcs
Part Number
tonne lbs W D F K H R L lbs box
1.0 2,200 1.97 0.55 1.06 1.50 2.17 0.94 4.13 1.1 45 28-057-1T
3.0 6,600 2.28 0.67 1.34 1.89 2.36 1.14 4.41 1.8 25 28-057-3T
5.0 11,000 2.52 0.87 1.69 2.40 2.91 1.30 6.06 4.0 12 28-057-5T
8.0 17,000 2.75 1.05 2.05 2.76 3.11 1.28 6.77 5.7 10 28-057-8T
10.0 22,000 2.95 1.19 2.17 2.95 4.14 1.58 7.52 6.8 8 28-057-10T
**See Page 14 for Grade 80 Chain**
Welding Instruction - The welding should only be carried out by qualified welder according to Standards, e.g. EN 287 or AWS.
Support material - Material of the welding block is S355J2+N (1.0577+N, St 52-3N, B.S. 4360.50D, AISI 1019 etc.).
- Prior to welding, the contact areas must be free from impurities, oil, paint, rust, scale, etc., for example by grinding. If the surface
is at all corroded, all rust must be completely removed from the weld area. Painted surface must be prepared in the same way.
- The steel support member must have a carbon content of no less than 0.25% and no more than 0.40%.
- In ambient temperature of 10ºC and below, pre-heating of the weld area prior to welding must be carried out.
Seam welding - The welds must be sufficiently strong to take the required loads.
- The distance lugs assist in achieving the required root weld (approx. 3 mm).
- A minimum weld-seam width must be maintained to give adequate weld strength (see table)
- Start both, the root pass and final weld pass from the centre of the support to be welded.
- Before starting the final weld pass, clean well the root pass to avoid inclusions.
- The complete welding operation must be carried out continuously so that the parts do not have time to cool.
- Do not weld at the yellow powder coated tempered load ring.
- After welding, ensure bail pivots full 180° without interfering with the weld.
- Effects of temperature - The lifting points for weld on, types DAA, can together with the load (e.g. weld construction) be
annealed, Temperature < 600° C, stress-release without reduction of WLL.
- The complete construction can be annealed stress release at <600°C without reduction of WLL.
- Do not rapidly cool the weld.
- A thorough inspection of the weld should be performed. No cracks, pitting, inclusions, notches or undercuts are allowed. If doubt
exists, use a suitable NDT method, such as magnetic particle or liquid penetrant to verify.
- If repair is required, grind out the defect and re-weld using the original qualified procedure.
Welding material: Weld material is to have a minimum tensile strength of 70,000 PSI (such as AWS A5.1 E-7018), following the electrode
manufacturer’s recommendations. Reference information as below:
MIG arc welding: Wire diameter 0.8 - 1.2 as per DIN 8559-SG 3, AWS A 5.18. Important: do not weld in the open air during bad weather
Manual electric: Direct current supply welding: Electrodes according to EN ISO 2560-A - E 42 6 B 3 2, AWS A 5.5 : E 8018-G. Electrode: root pass
and final weld pass, type E5154 B10 as per DIN 1913, used in accordance with the manufacturers.
Alternating current supply welding: Electrode as per DIN 1913, modified for alternating current use. HV welding and final weld pass, type E5155 B10.
WLL Thickness Weld Size

Part Number
tonne A (mm) S (mm)
28-057-1T 1.0 10 S=A+3
28-057-3T 3.0 12 S=A+4
28-057-5T 5.0 17 S=A+5
28-057-8T 8.0 16 S=A+4
28-057-10T 10.0 17 S=A+5
30
30
32
Grade 100 Forged Oblong Master Link
Drop Forged and embossed with Product Identification Code (PIC) for material traceability, along with
size and name “YOKE”
Full certificates available on request
Inside Inside Standard X-003

WLL 5:1 Dia.
Trade size length width Wt lbs Pcs. Box
Pounds (inches) Part Number
(inches) (inches)
7,400 *1/2" 4.72 2.76 0.55 1.1 50 28-X-1/2"ML
9,000 *5/8" 5.51 3.15 0.67 1.6 30 28-X-5/8"ML
12,300 *3/4" 5.91 3.54 0.75 2.4 20 28-X-3/4"ML
15,200 *7/8” 6.30 3.74 0.87 3.5 16 28-X-7/8”ML
26,000 *1" 7.48 4.33 0.98 5.1 10 28-X-1"ML
30,000 *1-1/8” 7.09 4.13 1.10 5.9 10 28-X-1-1/8”ML
39,100 *1-1/4” 7.87 4.72 1.18 7.6 7 28-X-1-1/4”ML
42,000 *1-3/8” 9.45 5.51 1.34 11.7 4 28-X-1-3/8”ML
61,100 *1-1/2” 9.84 5.91 1.50 15.8 3 28-X-1-1/2”ML
**See page 17 for Grade 100 Chain**
311
33
NEW SIZES
AVAILABLE
G-100 Connecting Link esign factor 4:1 proof tested and certified - Cert supplied on request
Grade 100 Dimensions (inches) Wt. Pcs Price
WLL lbs Part Number
Chain A B D K Lbs box each
9/32 5,700 0.71 0.98 0.35 2.32 0.4 150 28-X-7-8CL
3/8 8,800 0.98 1.10 0.43 2.72 0.7 50 28-X-10CL
1/2 15,000 1.18 1.50 0.63 3.62 1.5 35 28-X-13CL
5/8 22,600 1.42 1.61 0.75 3.98 2.6 20 28-X-16CL
3/4 35,300 1.65 1.97 0.91 4.80 4.2 12 28-X-18-20CL
7/8 42,700 1.93 2.48 0.95 5.98 7.7 6 28-X-22CL
1 59,700 2.17 2.60 1.18 6.38 11.7 3 28-X-26CL
NEW SIZES
AVAILABLE
G-100 ye Self Locking ook esign factor 4:1 proof tested and certified - Cert supplied on request
WLL lbs Part Number
Chain A D H K P T lbs box each
1/4-5/16 5,700 0.98 0.43 1.02 5.35 1.34 0.79 1.8 20 28-X-7-8SLEH
3/8 8,800 1.26 0.51 1.34 6.57 1.73 1.02 3.3 15 28-X-10SLEH
1/2 15,000 1.57 0.63 1.65 8.15 2.01 1.18 6.6 8 28-X-13SLEH
5/8 22,600 1.97 0.83 2.20 9.92 2.36 1.42 12.5 4 28-X-16SLEH
3/4 35,300 2.36 0.91 2.56 11.42 2.76 2.09 22.2 2 28-X-18-20SLEH
7/8 42,700 2.76 0.94 2.80 12.56 3.15 1.93 24.0 2 28-X-22SLEH
NEW SIZES
AVAILABLE
G-100 Clevis Self Locking ook esign factor 4:1 proof tested and certified Cert supplied on request
WLL lbs Part Number
Chain H K P T lbs Box each
1/4-5/16 5,700 1.02 4.69 1.34 0.79 1.8 25 28-X-7-8SLCH
3/8 8,800 1.34 5.59 1.73 1.02 3.1 15 28-X-10SLCH
1/2 15,000 1.65 7.01 2.01 1.18 6.2 8 28-X-13SLCH
5/8 22,600 2.20 8.39 2.36 1.42 12.3 4 28-X-16SLCH
3/4 35,300 2.56 9.61 2.76 2.09 19.8 2 28-X-18-20SLCH
7/8 42,700 2.80 10.75 3.15 1.93 24.0 2 28-X-22SLCH
32
32
34
G-100 Clevis Sling Hook – Design factor 4:1 proof tested and certified - Cert supplied on request
r 100 S are Latch it Dimensions (inches) Wt. Pcs Price oo Part
WLL lbs
hain Price Part P1 T Lbs box each Number
9/32 5,700 7.89 28-7-8LK 0.39 0.87 3.86 1.06 0.71 1.3 40 28-X-7-8 S
3/8 8,800 9.93 28-10LK 0.43 1.18 4.80 1.34 0.94 2.4 15 28-X-10 S
1/2 15,000 13.20 28-13LK 0.59 1.46 5.79 1.73 1.18 5.1 10 28-X-13 S
5/8 22,600 16.57 28-16LK 0.71 1.65 6.54 1.89 1.54 8.6 6 28-X-1 S
3/4 35,300 19.81 28-18-20LK 0.87 2.52 8.15 2.24 1.89 18.9 3 28-X-18-20 S
NEW SIZES
AVAILABLE
Grade 100 Eye Sling Hook - Design factor 4:1 proof tested & certified - Cert supplied on request
rade 100 Latch its Dimensions (inches) Pcs Price
WLL lbs Wt. lbs Part Number
hain Price Part P1 D T box each
9/32 7.89 28-7-8LK 5,700 3.86 1.10 0.98 0.47 0.79 0.91 1.1 50 28-X-7-8 S
3/8 9.93 28-10LK 8,800 4.76 1.42 1.26 0.59 0.91 1.22 2.0 25 28-X-10 S
1/2 13.20 28-13LK 15,000 5.98 1.58 1.57 0.71 1.06 1.50 3.5 12 28-X-13 S
7/8 29.48 28-22LK 42,700 9.65 2.99 2.01 1.22 2.05 2.48 20.5 3 28-X-22 S
G-100 Clevis Grab Hook – Design factor 4:1 proof tested and certified - Cert supplied on request
rade 100 Dimensions (inches) Wt. Pcs Price
WLL lbs Part Number
hain L P Lbs box each
1/4-5/16 5,700 0.39 1.18 0.87 2.17 3.66 0.39 0.7 70 28-X-7-8
3/8 8,800 0.43 1.61 1.14 3.03 5.04 0.51 1.8 30 28-X-10
1/2 15,000 0.59 2.05 1.50 3.90 6.50 0.67 3.5 15 28-X-13
5/8 22,600 0.71 2.24 1.77 4.49 7.68 0.83 5.9 10 28-X-1
3/4 35,300 0.87 2.87 2.05 5.12 8.74 0.91 10.1 5 28-X-18-20
33
35
G-100 GRIP SELF LOCKING HOOK
Grade 100 X-950 series self locking eye hook with grip for easy hook up and protected trigger
Embossed with Product Identification Code (PIC) for material traceability, along with size and name
“YOKE”
Design factor 4:1 proof tested and certified
Patent pending
G-100 Eye Grip Self Locking Hook – Design factor 4:1 proof tested and certified - Cert supplied on request.
rade 100 WLL / N.W. / Dimensions / inch Part
hain lbs lbs W P T D Number
3/8 8,800 4.19 6.89 5.47 2.80 1.93 1.26 1.06 0.51 1.22 28-X- 50-10
1/2 15,000 6.61 8.94 6.85 3.15 2.24 1.57 1.34 0.63 1.54 28-X- 50-13
5/8 22,600 13.89 10.91 8.35 4.49 3.07 1.97 1.54 0.83 1.85 28-X- 50-1
3/4 35,300 25.79 12.95 9.84 5.00 3.58 2.36 2.13 0.91 2.20 28-X- 50-20
7/8 42,700 31.96 13.78 10.24 5.95 4.13 2.76 2.20 0.94 2.32 28-X- 50-22
***Specifications can change without notice***
G-100 Swivel Grip Self Locking Hook with Ball Bearing. Ball Bearing, performs to fully swivel under load –
Design factor 4:1 proof tested and certified - Cert supplied on request
rade 100 WLL / Dimensions / inch
N.W. / lbs Part Number
hain lbs W P B T D
3/8 8,800 5.29 8.86 5.47 2.80 1.93 1.61 1.34 1.06 0.63 1.22 28-X- 52N-10
1/2 15,000 11.46 11.22 6.85 3.15 2.24 1.81 1.73 1.34 0.83 1.54 28-X- 52N-13
5/8 22,600 18.51 13.58 8.35 4.49 3.07 2.40 1.97 1.54 0.91 1.85 28-X- 52N-1
3/4 35,300 31.96 17.05 9.84 5.00 3.58 2.91 3.23 2.13 0.98 2.20 28-X- 52N-20
7/8 42,700 43.86 18.70 10.24 5.94 4.13 3.82 3.74 2.20 1.30 2.32 28-X- 52N-22
***Specifications can change without notice***
34
36
NEW SIZES
AVAILABLE
G-100 Swivel Self Locking Hook with Brass Bushing – Design factor 4:1 proof tested and certified -
Cert supplied on request
rade 100 Dimensions (inches) Wt. Pcs Brass Bushing
WLL lbs
chain B D P lbsT box Part Number
1/4-5/16 5,700 1.42 1.14 0.51 1.02 7.32 1.34 0.79 2.4 20 28-X-7-8SSL
3/8 8,800 1.61 1.34 0.63 1.34 8.58 1.73 1.02 4.4 12 28-X-10SSL
1/2 15,000 1.81 1.69 0.83 1.65 10.87 2.01 1.18 8.8 6 28-X-13SSL
5/8 22,600 2.40 1.97 0.91 2.20 12.95 2.36 1.42 15.0 3 28-X-1 SSL
3/4 35,300 2.91 3.23 0.98 2.56 15.24 2.76 1.93 27.8 2 28-X-18-20SSL
7/8 42,700 3.82 3.74 1.30 2.80 17.99 3.15 2.09 39.6 1 28-X-22SSL
1 59,700 4.84 4.53 2.01 3.11 21.06 3.90 2.20 69.3 1 28-X-2 SSL
G-100 Swivel Self Locking Hook with Ball Bearing. Ball Bearing, performs to fully swivel under
load – Design factor 4:1 proof tested and certified - Cert supplied on request
rade 100 Dimensions (inches) Wt. Pcs Brass Bushing

WLL lbs
chain B D P T lbs box Part Number
5/8 22,600 2.40 1.97 0.91 2.20 12.95 2.36 1.42 15.0 3 28-X-1 SWBB
3/4 35,300 2.91 3.23 0.98 2.56 15.24 2.76 1.93 27.8 2 28-X-18-20SWBB
7/8 42,700 3.82 3.74 1.30 2.80 17.99 3.15 2.09 39.6 1 28-X-22SWBB
35
37
OVERHEAD LIFTING CHAIN
Specifically recommended for overhead lifting

25% stronger than System 8
Enables you to perform same lifts with lighter weight chain
System 10 chain should not be plated or galvanized
Hallmarking: C10 and traceability code
To prevent the possibility of serious bodily harm:
Standard material: Alloy steel, heat treated DO NOT EXCEED the working load limits of chain or components
DO NOT USE if the chain or components are visibly distorted or worn
Standard finish: Bright (BRT)
Proof tested
Order unit is “Feet”
Over Head Lifting Chain – Grade 100

Trade WLL 4:1 Material Inside Inside eet Per Lbs er
Part Number
Size lbs Diameter Length Width Drum 100 t
9/32” 4,300 0.29” 0.86” 0.41” 500 70 040-5212

3/8” 8,800 0.40” 1.22” 0.55” 500 142 040-5412
1/2” 15,000 0.52” 1.57” 0.75” 300 244 040-5512
5/8” 22,600 0.64” 1.93” 0.87” 200 356 040-5 12
3/4” 35,300 0.80” 2.42” 1.09” 100 598 040-5712

Chain Grade 100 Size
inch mm 90° 60° 45° 30° 60° 45° 30°

7/32 6 2700 4700 3800 2700 7000 5700 4000
1/4~9/32 7 4300 7400 6100 4300 11200 9100 6400
5/16 8 5700 9900 8100 5700 14800 12100 8500
3/8 10 8800 15200 12400 8800 22900 18700 13200
1/2 13 15000 26000 21200 15000 39000 31800 22500
5/8 16 22600 39100 32000 22600 58700 47900 33900
3/4 20 35300 61100 49900 35300 91700 74900 52950
7/8 22 42700 74000 60400 42700 110900 90600 64000
36
38
Swivel – JAW + JAW
x All Yoke Swivels are manufactured using the highest grade of material available
x Tested to 2 times the Working Load Limit with certification
x Zinc plated for corrosion resistance and longer life
x Grease fittings for superior performance
x Designed for low starting torque and high rotation speed
x 20,000 cycle fatigue rated to 1.5 times WLL
x 100% magnaflux crack detection
x All parts with batch number for quality certified and traceability
Angular Contact Bearing Swivel – Jaw + Jaw

Wire Dimensions (inches)
Weight Part
Line WLL
B L D lbs Number
Size
1/2 3 2.00 6.20 8.20 1.00 0.90 0.80 0.40 1.30 5.1 28-303-03
5/8 5 2.50 8.00 10.30 1.20 1.30 0.90 0.60 1.50 9.7 28-303-05
¾ 8.5 3.00 10.00 12.60 1.30 1.60 1.20 0.60 2.10 16.8 28-303-085
7/8 10 4.00 12.40 16.20 1.90 1.70 1.50 1.00 2.10 43.0 28-303-10
1 15 4.30 12.40 16.50 2.00 1.90 1.50 1.00 2.20 48.6 1 28-303-15
1-1/4 25 5.20 14.70 20.00 2.60 2.40 2.00 1.20 2.80 87.0 28-303-25
x Minimum Ultimate Load is 5 times the Working Load Limit
x Proof Load is 2 times the Working load Limit
37
39
Swivel EYE + EYE
Angular Contact Bearing Swivel – Eye + Eye

Wire Dimensions (inches)
WLL Weight
Line Part Number
tonne B L I T W lbs
Size
1/2 3 2.00 6.20 8.43 1.10 0.80 1.10 2.00 4.6 28-30 -03
5/8 5 2.50 8.30 10.90 1.30 1.00 1.30 2.30 9.5 28-30 -05
3/4 8.5 3.00 9.80 12.80 1.50 1.30 1.50 3.20 16.1 28-30 -085
7/8 10 4.00 12.20 16.30 2.10 1.70 2.00 3.50 37.4 28-30 -10
1 15 4.30 12.40 17.40 2.50 1.90 2.50 4.30 46.0 28-30 -15
1-1/4 25 5.20 16.00 21.50 2.80 2.33 2.63 5.30 86.0 28-30 -25
1-1/2 31.5 5.00 16.00 20.75 2.38 2.25 2.31 5.25 72.0 28-30 -35
38
40
Swivel - Bullet Style
Angular Contact Bearing Swivel – Bullet Style

Wire Tor ue in Nm
Dimensions (inches) Weight
Line WLL Part Number
lbs
Size B L D
1/2 3 2.00 6.3 8.00 0.90 0.90 0.60 1.20 4.4 28-301-03
5/8 5 2.50 8.00 10.30 1.20 1.30 0.90 1.50 8.7 28-301-05
¾ 8.5 3.00 9.50 12.30 1.40 1.50 1.00 2.00 14.8 28-301-085
7/8 10 4.00 12.50 16.00 1.80 1.70 1.50 2.10 41.1 28-301-10
1 15 4.30 12.50 16.00 1.80 2.00 1.50 2.20 45.5 28-301-15
1-1/4 25 5.20 14.70 19.50 2.40 2.50 2.00 2.70 80.0 28-301-25
39
41
Light Duty Snatch Block, Single Sheave with Shackle
Sheave Working
Wire Size Dimensions (inch) N.W.
Dia. Load Limit Part Number
mm inch inch tonne A B E F G K L R lbs
8-10 5/16~3/8 3 2 1.38 1.18 2.52 0.43 2.95 5.91 8.96 8.53 5 28-501-02
10-13 3/8~1/2 4.5 4 2.52 1.97 3.11 0.75 4.21 9.57 14.02 13.27 13 28-501-04
16-19 5/8~3/4 6 8 3.43 2.99 4.09 1.26 5.98 12.60 19.06 17.80 29 28-501-08
16-19 5/8~3/4 8 8 3.43 2.99 4.09 1.26 8.66 13.10 21.90 20.64 43 28-501-0808
Light Duty Snatch Block, Single Sheave with Hook

Sheave Working
mm inch inch tonne E G I L P R T lbs
8-10 5/16~3/8 3 2 2.52 2.95 1.00 9.90 1.00 8.80 0.69 6 28-502-02
10-13 3/8~1/2 4.5 4 3.11 4.24 1.88 14.00 1.25 12.62 1.13 13 28-502-04
16-19 5/8~3/4 6 8 4.09 5.98 2.13 19.20 2.00 16.80 1.50 29 28-502-08
16-19 5/8~3/4 8 8 4.09 8.70 2.13 22.20 2.00 19.80 1.50 42 28-502-0808
Light Duty Snatch Block, Single Sheave Tailboard

Sheave Working
mm inch inch tonne E G H J M N P Q lbs
8-10 5/16~3/8 3 2 2.52 2.95 4.88 2.64 0.98 0.67 0.75 0.75 3 28-503-02
10-13 3/8~1/2 4.5 4 3.11 4.21 7.72 4.21 1.50 1.06 1.14 1.38 8 28-503-04
16-19 5/8~3/4 6 8 4.09 5.98 9.84 5.12 1.81 1.22 1.30 1.73 15 28-503-08
16-19 5/8~3/4 8 8 4.09 8.66 12.80 6.73 1.81 1.22 1.30 1.73 29 28-503-0808
40
40
42
Forged Snatch Block, Single Sheave with Shackle
Sheave Working
Wire Size Dimensions (inch) N.W. Price
each
19-22 3/4~7/8 8 15 3.07 3.15 5.28 1.73 8.66 13.99 23.19 21.46 61 28-541-15
Forged Snatch Block, Single Sheave with Hook

Sheave Working
Dia. Load Limit Price each Part Number
19-22 3/4~7/8 8 15 5.28 8.67 2.63 24.20 2.50 21.50 1.94 62 28-542-15
Alloy Snatch Block, Single Sheave with Shackle

Sheave Working
Wire Size Dimensions (inch) N.W. Price
each
19-22 3/4~7/8 8 12 3.43 2.99 4.09 1.26 8.66 13.10 21.90 20.64 36 28-561-1208
41
41
43
Super Snatch Block, Single Sheave with Shackle
Sheave Working
25-29 1~1-1/8 8 20 4.29 3.66 5.91 2.17 8.50 17.05 26.42 14.88 91 28-551-20
Super Snatch Block, Single Sheave with Hook

Sheave Working
25-29 1~1-1/8 8 20 13.82 8.51 3.00 28.00 3.38 25.30 2.38 91 28-552-20
Super Snatch Block, Single Sheave, Tailboard

Sheave Working
mm inch inch tonne E G H J M N P Q lbs
25-29 1~1-1/8 8 20 5.91 8.50 13.50 6.89 2.52 1.93 2.09 2.36 50 28-553-20
42
42
44
Van Beest Green Pin Shackles
SEE WARNING AND APPLICATION INFORMATION – PAGE 120
“Green Pin” Super Shackle Safety Pin (5:1 WLL)

Van Beest Super Alloy Shackle
High strength alloy
Made in Holland
All shackles can be supplied with 3.1-B certificates
Van Beest is certified by DNV to DNV 2.7-1
Van Beest mill in Holland is approved to DNV, ABS, Lloyd’s & Germanischer Lloyd.
WLL te Trade Size a (mm) C (mm) D (mm) d (mm) 2r (mm) Wt. Kg Price Part Number
30 1-1/2” 60 146 38 42 99 8.79 529.69 25-30SUPERSA
40 1-3/4” 74 178 45 50 126 15 834.90 25-40SUPERSA
55 2” 83 197 57 57 138 22 1,199.72 25-55SUPERSA
85 2-1/2” 105 260 70 70 180 42 1,850.40 25-85SUPERSA
120 3” 127 329 83 83 190 70 2,852.77 25-120SUPERSA
150 3-1/2” 147 400 95 95 238 112 6,769.72 25-150SUPERSA
1 tonne (te) = 2200 lbs
“Green Pin” Screw Pin (6:1)

Van Beest Screw Pin Shackle
Made in Holland
All shackles can be supplied with 3.1-B certificates
Van Beest is certified by DNV to DNV 2.7-1
Van Beest mill in Holland is approved to DNV, ABS, Lloyd’s & Germanischer Lloyd.
WLL te Size A (mm) C (mm) D (mm) d (mm) 2r (mm) Wt. Kg Price Part Number
0.33 3/16" 9.5 22 5 6 16 0.02 6.26 25-.33SP
0.5 1/4" 12 29 7 8 20 0.06 6.47 25-.5SP
0.75 5/16" 13.5 32 9 10 21 0.11 7.02 25-.75SP
1 3/8" 17 36.5 10 11 26 0.15 7.95 25-1SP
1.5 7/16" 18.5 43 11 12 29 0.21 10.45 25-1.5SP
2 1/2" 22 51 13.5 16 32 0.37 15.05 25-2SP
3.25 5/8" 27 64 16 19 43 0.65 22.91 25-3.25SP
4.75 3/4" 31 76 19 22 51 1.06 33.25 25-4.75SP
6.5 7/8" 36 83 22 25 58 1.56 48.73 25-6.5SP
8.5 1" 43 95 25 28 68 2.32 63.30 25-8.5SP
9.5 1 1/8" 47 108 28 32 75 3.28 102.73 25-9.5SP
12 1 1/4" 51 115 32 35 83 4.51 132.95 25-12SP
13.5 1 3/8" 57 133 35 38 92 5.93 149.48 25-13.5SP
17 1 1/2" 60 146 38 42 99 7.89 217.45 25-17SP
25 1 3/4" 74 178 45 50 126 13.40 360.81 25-25SP
35 2" 83 197 50 57 138 18.85 462.35 25-35SP
55 2-1/2” 105 266.5 65 70 180 37.86 986.76 25-55SP
! WARNING
NEVER EXCEED PUBLISHED WORKING LOAD LIMIT
45
SHACKLES
“Green Pin” Safety Bolt Anchor Shackle

Van Beest Safety Pin Shackle
Made in Holland
All shackles can be supplied with 3.1-B certificates
Van Beest is certified by DnV to DnV 2.7-1
Van Beest mill in Holland is certified to DnV, ABS, Lloyd’s & Germanischer Lloyd.
WLL te Size a C D d - pin 2r Wt. kg Part Number
1 3/8" 17 36.5 10 11 26 0.17 25-1SA
2 1/2" 22 51 13.5 16 32 0.44 25-2SA
3.25 5/8" 27 64 16 19 43 0.79 25-3.25SA
4.75 3/4" 31 76 19 22 51 1.26 25-4.75SA
6.5 7/8" 36 83 22 25 58 1.88 25-6.5SA
8.5 1" 43 95 25 28 68 2.78 25-8.5SA
9.5 1 1/8" 47 108 28 32 75 3.87 25-9.5SA
12 1 1/4" 51 115 32 35 83 5.26 25-12SA
13.5 1 3/8" 57 133 35 38 92 6.94 25-13.5SA
17 1 1/2" 60 146 38 42 99 8.79 25-17SA
25 1 3/4" 74 178 45 50 126 14.99 25-25SA
35 2" 83 197 50 57 138 20.65 25-35SA
55 2 1/2" 105 260 65 70 180 41.05 25-55SA
85 3" 127 330 75 80 190 62.24 25-85SA
“Green Pin” Shackle

Van Beest Wide Mouth Towing Shackle
Made in Holland
Bow and pin alloy steel, grade 8, quenched and tempered
Hot dip galvanized
Only to be used for towing with correct loading across the pin.
WLL te Size a C D d - pin 2r Wt. kg Part Number
22 1-1/2 106 216 38 42 159 12.5 25-22WMTS
30 1-3/4 127 248 45 50 175 18 25-30WMTS
40 2 146 273 50 57 207 25 25-40WMTS
44
44
46
SHACKLES
Screw Pin Anchor Bow Shackle, “Yellow Pin” – (6:1 WLL) Galvanized, dimensions aprox.
Federal Specification RR-C-271D, Type IVA, Grade A, Class 2.
Forged – Quenched and Tempered, Alloy Pins.
To assure traceability, “Yellow Pin” shackles are embossed to exceed ASME B30.26 requirements.
x “OCEAN”
x Size
x Alloy Pin ID
x WLL (Working Load Limit)
x Production Code – Traceable to certificate & material
x Powder Coated “Yellow Pin” for instant recognition
Size WLL Weight Pcs Part
A B C D E F
inches tonne (lbs) Box Number
3/16” 1/3 0.19 0.25 0.88 0.38 0.56 0.60 0.06 1000 6-3/16”SPB
1/4” 1/2 0.25 0.31 1.13 0.47 0.61 0.78 0.10 500 6-1/4”SPB
5/16” 3/4 0.31 0.38 1.22 0.53 0.75 0.84 0.19 300 6-5/16”SPB
3/8” 1 0.38 0.44 1.44 0.66 0.91 1.03 0.31 200 6-3/8”SPB
7/16” 1 1/2 0.44 0.50 1.69 0.75 1.06 1.16 0.38 150 6-7/16”SPB
1/2” 2 0.50 0.63 1.88 0.81 1.19 1.31 0.72 80 6-1/2”SPB
5/8” 3 1/4 0.63 0.75 2.38 1.06 1.50 1.69 1.37 40 6-5/8”SPB
3/4” 4 3/4 0.75 0.88 2.81 1.25 1.81 2.00 2.35 25 6-3/4”SPB
7/8” 6 1/2 0.88 1.00 3.31 1.44 2.09 2.28 3.62 15 6-7/8”SPB
1” 8 1/2 1.00 1.13 3.75 1.69 2.38 2.69 5.03 10 6-1”SPB
1-1/8” 9 1/2 1.16 1.25 4.25 1.81 2.69 2.91 7.41 6 6-1-1/8”SPB
1-1/4” 12 1.29 1.38 4.69 2.03 3.00 3.25 9.05 5 6-1-1/4”SPB
1-3/8” 13 1/2 1.42 1.50 5.25 2.25 3.31 3.63 13.53 4 6-1-3/8”SPB
1-1/2” 17 1.54 1.63 5.75 2.38 3.63 3.88 17.20 3 6-1-1/2”SPB
1-3/4” 25 1.84 2.00 7.00 2.88 4.19 5.00 27.78 2 6-1-3/4”SPB
2” 35 2.08 2.25 7.75 3.25 4.81 5.75 45.00 2 6-2”SPB
2-1/2” 55 2.71 2.75 10.50 4.13 5.69 7.25 85.75 1 6-2-1/2”SPB
45
45
47
SHACKLES
Safety Anchor Bow Shackle, “Yellow Pin Shackles” – (6:1 WLL) Galvanized, dimensions aprox.
Federal Specification RR-C-271D, Type IVA, Grade A, Class 3.
Forged – Quenched and Tempered, Alloy Pins.
To assure traceability, “Yellow Pin” shackles are embossed to exceed ASME B30.26 requirements.
x Size
x Alloy Pin ID
x WLL (Working Load Limit)
x Production Code – Traceable to certificate & material
x Powder Coated “Yellow Pin” for instant recognition
Size WLL Pin Wt. Pcs
A B C D E F Part Number
inches Tonne length (lbs) Box
1/4" 1/2 0.25 0.31 1.13 0.47 0.61 0.78 1.56 .11 500 6-1/4”SA
5/16” 3/4 0.31 0.38 1.22 0.53 0.75 0.84 1.82 .22 300 6-5/16”SA
3/8” 1 0.38 0.44 1.44 0.66 0.91 1.03 2.17 0.33 200 6-3/8”SA
7/16” 1-1/2 0.44 0.50 1.69 0.75 1.06 1.16 2.51 0.49 150 6-7/16”SA
1/2" 2 0.50 0.63 1.88 0.81 1.19 1.31 2.80 0.79 80 6-1/2”SA
5/8” 3 1/4 0.63 0.75 2.38 1.06 1.50 1.69 3.53 1.68 40 6-5/8”SA
3/4" 4 3/4 0.75 0.86 2.81 1.25 1.81 2.00 4.07 2.72 25 6-3/4”SA
7/8” 6 1/2 0.88 1.00 3.31 1.44 2.09 2.28 4.71 3.95 15 6-7/8”SA
1” 8 1/2 1.00 1.13 3.75 1.69 2.38 2.69 5.31 5.66 10 6-1”SA
1-1/8” 9 1/2 1.13 1.25 4.25 1.81 2.69 2.91 5.90 8.27 6 6-1-1/8”SA
1-1/4” 12 1.25 1.38 4.69 2.03 3.00 3.25 6.51 11.71 5 6-1-1/4”SA
1-3/8” 13 1/2 1.38 1.50 5.25 2.25 3.31 3.63 7.21 15.83 4 6-1-3/8”SA
1-1/2” 17 1.50 1.63 5.75 2.38 3.63 3.88 7.73 20.80 3 6-1-1/2”SA
1-3/4” 25 1.75 2.00 7.00 2.88 4.19 5.00 9.05 33.91 2 6-1-3/4”SA
2” 35 2.00 2.25 7.75 3.25 4.81 5.75 10.41 52.25 2 6-2”SA
46
46
48
SHACKLES
Shackles are forged alloy steel with alloy pin

Size & Working load Limit permanently shown on each shackle
All shackles with Batch Code that links to Test Certificate and
Quality Traceability.
100% magnaflux crack detection during manufacturing.
20,000 cycle fatigue rated to 1.5 times working load limit.
Forged Alloy Wide Body Shackle - with Bolt Pin

Size WLL Dimensions (inch) Wt Part
inch tonne A B C D E G H K R W lbs Number
3/4” 7 3.58 1.61 0.70 0.87 1.26 1.81 5.90 4.10 1.26 1.30 3.7 28-809-19
1” 12.5 4.64 2.12 0.91 1.14 1.61 2.40 7.64 5.51 1.38 1.73 8.4 28-809-26
1-1/4” 18 5.83 2.52 1.18 1.42 2.00 2.68 9.37 6.77 1.50 2.13 15 28-809-32
1-1/2” 30 6.93 3.15 1.38 1.77 2.50 3.50 11.38 8.50 1.77 2.36 27 28-809-38
Minimum Ultimate Load is 5.4 times the Working Load Limit
Maximum Proof Load is 2 times the Working Load Limit
1 tonne = 2200 lbs
47
47
49
SHACKLES
GN Bow Safety Pin Shackle Type H9 & H10
Material up to and including 120 T - forged high tensile steel, above 120 T - forged high alloy steel. 6:1 safety from 25 T to 85 T.
5:1 safety from 120 T to 1000 T to US Federal Spec RR-C-271. Provided with Manufacturer certificate of compliance, EN10204
3.1, test results for chemical analysis, charpy impact test requests taken at -40°C on a finished shackle after treat treatment of a
batch lot production.
WLL Safety Dimensions (mm) Wt.

Part Number
tonne factor A B C D E F kg
25 6:1 45 50 178 126 74 104 13 116-25SA
35 6:1 50 57 197 138 83 119 18 116-35SA
42.5 6:1 57 65 220 160 95 134 26 116-42.5SA
55 6:1 65 70 260 180 105 145 35 116-55SA
85 6:1 75 83 330 190 127 163 53 116-85SA
120 5:1 89 95 381 238 150 200 110 116-120SA
150 5:1 102 108 400 275 170 230 160 116-150SA
200 5:1 120 125 500 290 180 260 235 116-200SA
250 5:1 125 140 540 305 200 260 285 116-250SA
300 5:1 135 150 600 305 200 305 340 116-300SA
400 5:1 165 175 650 325 225 350 560 116-400SA
500 5:1 175 185 700 350 250 370 685 116-500SA
600 5:1 195 205 700 375 275 405 880 116-600SA
700 5:1 205 215 700 400 300 435 980 116-700SA
800 5:1 210 220 700 400 300 435 1100 116-800SA
900 5:1 220 230 700 420 320 465 1280 116-900SA
1000 5:1 230 240 700 420 340 480 1460 116-1000SA
Tolerance + 5% 1 tonne = 2200 lbs
Cold Temperature application – General Information

There has been a lot of discussion in recent months about cold temperature shackles. There is a miss
conception that if a shackle complies with DNV 2.7-1 it is certified for cold temperature use and conforms
to CAPP requirements. Use web site (http://exchange.dnv.com/publishing/StdCert/Standard2-7-1.pdf) to
obtain a copy of DNV 2.7-1. DNV rules are written for the world not just the cold areas therefore why
would a shackle used in the tropics have to have a cold temperature rating. DNV’s material requirement is
to have a minimum charpy impact testing at the design working temperature see section 8.4. Make sure the
shackle you are using has actually been tested at the working temperature you are using them. Most areas of
Canada are going to require a temperature of minus 40°C and achieving a 42 jewel impact result. These
parameters and results should be stated on documentation, identification marking should link all
documentation to the individual product. Based on EN10204 (3.1 or 3.2) primary and incoming material can
be tested for standard compliance (section 4). Both of these standards are a requirement for CAPP. Be
informed to make sure your inspection and documentation matches your client’s expectations. We have two
manufacturers who comply with DNV for Cold temperature results at -40°C, VanBeest (Polar shackle) and
GN Rope Fittings. Yoke also has shackles certified to DNV standards however not for cold temperature
applications. We are able for an additional charge perform extra 3rd party libratory testing on our stock lots
should additional testing be required, these would be added as an appendix to the manufacturer’s certificate
of compliance and EN10204 certificate that can be traced to the lot production.
48
48
50
SHACKLE WARNINGS AND APPLICATIONS
Side and symmetrical loading data applies to screw pin and bolt nut cotter shackles only!
Side and symmetrical loading not permitted on round pin shackles.
Angles of Side Load
0° - In-Line - 100 % of rated WLL (Working Load Limit)
45° - From In-Line – 70% of rated WLL
90° - From In-Line – 50% of rated WLL
Symmetrical Loading
Shackles symmetrically loaded with two legs at a maximum angle
Of 120°can be used to full Working Load Limit.
-For permanent or long term installation always use nut and cotter.
-Shackle must be large enough to avoid pinching or bunching of synthetic slings.
-Diameter of shackle must be greater than wire rope diameter if no thimble in eye.
-Mouse screw pin when used in long term or high vibration applications.
Shackles should be inspected before use to ensure that:

All markings are legible
7KHERG\DQGSLQDUHERWKLGHQWLILDEOHDV being of the same size, type and make
7KHWKUHDGVRIWKHSLQDQGWKHERG\DUHXQGDPDJHG
Never use a safety bolt type shackle without using the cotter pin
7KHERG\DQGWKHSLQDUHQRWGLVWRUWHGRUworn
The body and pin are free from nicks, gouges, cracks and corrosion
6KDFNOHVPD\QRWEHKHDWWUHDWHGDVWKis may affect their Working Load Limit
Never modify, repair or reshape a shackle by welding, heating or bending as this will affect the
Working Load Limit
Select the correct type of shackle and its Working Load Limit for the particular application. Should
extreme circumstances or shock loading be applicable, this must be well taken into account on selecting
the correct shackle. Please note that commercial shackles are not to be used for lifting applications.
Make sure that the shackle is supporting the load correctly, i.e. along the axis of the shackle body
centerline, avoid introduction of bending loads, unstable loads and do not overload.
Wrong Right
Improper use or care of shackles can result in bodily injury or property damage
To avoid injury or property damage:
- Do not exceed the WLL (Working Load Limit)
- Do not shock load
- Do not side load – center line of load must coincide with center line of shackle
- Do not replace pin or bolt with other than original equipment
- Inspect before use for wear, deformation, and pin engagement
Inspect shackles before each use as outlined in ASME B30.26
49
49
51
Hoist Ring Working Load Application
UNC - Thread
204 series
Metric – Thread
203 series
50
52
UNC
Swivel Hoist Ring
x All Yoke Swivel Hoist Rings meet or exceed all the requirements of ASME B30.26
x Hoist Ring Bail are designed by forged alloy steel, quenched and tempered
x Each forged part and cap screw have batch coding and are linked to test certificate sheet
x Hoist rings are 360 swivel with 180 pivot function
x Yellow galvanized for increased anti-corrosion
x Bolt galvanized alternative phosphate treatment
x Rated 100% at 90 angle
x Self aligns in direction of load
Swivel Hoist Ring, with alloy steel washer - UNC Thread – Grade 8 alloy Socket Cap Screw per ASTM A574
- 28-204-070 and above use Hex Head Nut
Rated Spare Bolt & Clip Dimensions (inches) Swivel Hoist Ring
Torque ft Wt
Load Thread Size Lbs Spare Bolt Part
A B D E F G lbs Part Number
lbs Number
800 5/16”-18 x 2 7 28-P204-004 1.57 1.61 0.35 0.68 4.02 2.56 0.9 28-204-004
1,000 3/8”-16 x 2 12 28-P204-005 1.57 1.61 0.35 0.68 4.02 2.56 0.9 28-204-005
2,500 ½”-13 x 2.5 28 28-P204-010 2.56 2.32 0.59 0.71 6.26 4.13 3.7 28-204-010
2,500 ½”-13 x 3.0 28 28-P204-010L 2.56 2.32 0.59 1.22 6.26 4.13 3.7 28-204-010L
4,000 5/8”-11 x 2.5 60 28-P204-019 2.56 2.32 0.59 0.71 6.26 4.13 4.0 28-204-019
4,000 5/8”-11 x 3.25 60 28-P204-019L 2.56 2.32 0.59 1.69 6.26 4.13 4.0 28-204-019L
5,000 ¾”-10 x 2.75 100 28-P204-021 2.56 2.32 0.59 1.18 6.26 4.13 4.0 28-204-021
5,000 ¾”-10 x 3.25 100 28-P204-021L 2.56 2.32 0.59 1.65 6.26 4.13 4.2 28-204-021L
7,000 ¾”-10 x 3.0 100 28-P204-030 3.35 2.87 0.87 0.79 8.03 5.28 9.0 28-204-030
8,000 7/8”-9 x 3.5 160 28-P204-042 3.35 2.87 0.87 1.28 8.03 5.28 9.3 28-204-042
8,000 7/8”-9 x 4.25 160 28-P204-042L 3.35 2.87 0.87 2.24 8.03 5.28 9.7 28-204-042L
10,000 1”-8 x 3.5 230 28-P204-045 3.35 2.87 0.87 1.26 8.03 5.28 9.5 28-204-045
10,000 1”-8 x 4.5 230 28-P204-045L 3.35 2.87 0.87 2.28 8.03 5.28 9.7 28-204-045L
15,000 1-1/4” – 7 x 4.5 470 28-P204-070 3.95 3.15 1.00 2.20 8.58 6.30 14.8 28-204-070
24,000 1-1/2” – 6 x 6.5 800 28-P204-125 4.72 4.29 1.38 3.10 12.09 8.66 36.4 28-204-125
30,000 2” – 4.5 x 6.5 1100 28-P204-135 4.72 4.29 1.38 3.11 12.09 8.66 38.6 28-204-135
x Proof Load is 2.5 times the Working load Limit
x Additional styles available for soft metal products
x The depth of thread needs to be a minimum of 1 times the thread diameter for steel, 1.25 times for cast iron, 2 times for aluminum
51
53
METRIC
Swivel Hoist Ring
• All Yoke Swivel Hoist Rings meet or exceed all the requirements of ASME B30.26
• Bolts are metric thread ASME / ANSI B18.3.1 M
• Hoist Ring Bail are designed by forged alloy steel, quenched and tempered
• Each forged part and cap screw have batch coding and are linked to test certificate sheet
• Hoist rings are 360 swivel with 180 pivot function
• Yellow galvanized for increased anti-corrosion
• Bolt galvanized alternative phosphate treatment
• 20,000 cycle fatigue rated to 1.5 times WLL
• Rated 100% at 90 angle
• 100% magnaflux crack detection
• Self aligns in direction of load
Swivel Hoist Ring, alloy steel washer - Metric Thread – Grade 12.9 alloy Socket Cap Screw per DIN EN ISO 4762
- 28-203-070 and above use Hex Head Nut
WLL torque Spare Bolt & Clip Dimensions (mm) Wt
tonne Thread Size Nm
Part Number
Part Number A B D E F G Kg
5 to 1
0.40 M8-1.25 x 50 10 28-P203-004 40 41 9 16.5 102 65 0.4 28-203-004
0.45 M10-1.50 x 45 16 28-P203-005 40 41 9 11.5 102 65 0.5 28-203-005
1.05 M12-1.75 x 60 38 28-P203-010 65 64 15 14 158 105 1.7 28-203-010
1.05 M12-1.75 x 75 38 28-P203-010L 65 64 15 29 158 105 1.7 28-203-010L
1.90 M16-2.00 x 65 81 28-P203-019 65 64 15 19 158 105 1.8 28-203-019
1.90 M16-2.00 x 80 81 28-P203-019L 65 64 15 34 158 105 1.8 28-203-019L
2.15 M20-2.50 x 70 136 28-P203-021 65 64 15 24 158 105 1.9 28-203-021
2.15 M20-2.50 x 90 136 28-P203-021L 65 64 15 44 158 105 2.1 28-203-021L
3.00 M20-2.50 x 80 136 28-P203-030 85 79 19 25 204 134 4.2 28-203-030
4.20 M24-3.00 x 80 312 28-P203-042 85 79 19 25 204 134 4.2 28-203-042
4.20 M24-3.00 x 105 312 28-P203-042L 85 79 19 50 204 134 4.3 28-203-042L
7.00 M30-3.50 x 135 637 28-P203-070 100 100 25 77 241 160 6.7 28-203-070
11.00 M36-4.00 x 160 1005 28-P203-110 120 111 30 75 286 194 15.5 28-203-110
12.50 M42-4.50 x 175 1005 28-P203-125 120 111 30 90 286 194 16.5 28-203-125
13.50 M48-5.00 x 190 1350 28-P203-135 120 111 30 105 286 194 16.8 28-203-135
• Minimum Ultimate Load is 5 times the Working Load Limit
• Proof Load is 2.5 times the Working load Limit on the 4 to 1 design factor
• Additional styles available for soft metal products
• The depth of thread needs to be a minimum of 1 times the thread diameter for steel, 1.25 times for cast iron, 2 times for aluminum
52
54
GALVANIZED WIRE ROPE SLINGS
Galvanized Wire Rope Slings (5:1 by design API spec. 9a table 3.7)
Diameter of Wire Rope vs. standard length for Pricing
Length 1/4" 3/8" 1/2" 5/8" 3/4" 7/8" 1" 1-1/8" 1-1/4" 1-1/2" 1-3/4” 2” 2-1/4” 2-1/2”
2 ft 9.78 12.56 - - - - - - - - - - - -
3 ft 10.51 13.96 21.81 29.19 - - - - - - - - - -
4 ft 11.24 15.37 24.44 32.56 56.53 80.83 - - - - - - - -
5 ft 12.00 16.78 27.07 35.94 62.01 87.68 125.59 195.83 - - - - - -
6 ft 12.72 18.19 29.71 39.30 67.50 94.55 134.24 207.18 279.41 444.05 - - - -
7 ft 13.46 19.60 32.36 42.63 72.98 101.40 142.90 218.51 296.13 467.14 P.O.R - - -
8 ft 14.19 21.01 35.00 46.05 78.48 108.27 151.52 229.86 312.86 490.25 P.O.R - - -
9 ft 14.93 22.41 37.63 49.43 83.96 115.14 160.13 241.21 329.58 513.35 P.O.R P.O.R - -
10 ft 15.68 23.82 40.26 52.81 89.43 121.99 168.71 252.56 345.67 536.46 P.O.R P.O.R P.O.R -
11 ft 16.41 25.23 42.91 56.17 94.93 128.86 177.31 263.91 363.04 559.56 P.O.R P.O.R P.O.R P.O.R
12 ft 17.15 26.64 45.55 59.54 100.41 135.71 185.89 275.25 379.76 582.65 P.O.R P.O.R P.O.R P.O.R
15 ft 19.35 30.88 53.46 69.68 116.86 156.30 211.66 309.30 429.93 651.96 P.O.R P.O.R P.O.R P.O.R
20 ft 23.04 37.92 66.65 86.54 144.28 190.59 254.61 366.04 513.54 767.47 P.O.R P.O.R P.O.R P.O.R
Std. eye 2"x 4" 3"x 6" 4"x 8" 5"x10" 6"x12" 7"x14" 8"x16" 9"x18" 10"x20" 12"x24" 14”x28” 16”x32” 18”x36” 20”x40”
WLL
0.65 1.4 2.5 3.9 5.6 7.6 9.8 12 15 21 28 37 44 54
(ton)
Weight /
0.116 0.26 0.46 0.72 1.04 1.42 1.85 2.34 2.89 4.16 5.67 7.39 9.36 11.6
foot
** All wire rope slings made with EIPS, IWRC Galvanized Wire rope with steel ferrule and Flemish roll splice
complete with tag showing size, length, WLL and manufacture.
5
BRIGHT WIRE ROPE SLINGS
Bright Wire Rope Slings with A1 light lube (5:1 by design API spec. 9a table 3.7)
Diameter of Wire Rope vs. standard length for Pricing
Length 1/2" 5/8" 3/4" 7/8" 1" 1-1/8" 1-1/4"
3 ft 18.52 24.82 - - - - -
4 ft 20.78 27.68 48.04 68.70 - - -
5 ft 23.02 30.54 52.72 74.52 106.75 166.45 -
6 ft 25.24 33.40 57.38 80.37 114.09 176.10 237.50
7 ft 27.51 36.27 62.05 86.18 121.45 185.74 251.71
8 ft 29.74 39.14 66.71 92.02 128.81 195.38 265.93
9 ft 31.99 42.02 71.36 97.87 136.10 205.03 280.15
10 ft 34.24 44.89 76.03 103.69 143.42 214.68 294.37
11 ft 36.47 47.75 80.68 109.54 150.71 224.32 308.57
12 ft 38.72 50.61 85.36 115.35 158.00 233.97 322.78
15 ft 45.44 59.23 99.33 132.85 179.92 262.90 365.44
20 ft 56.66 73.56 122.64 162.01 216.42 311.14 436.51
Std. eye size 4"x 8" 5"x 10" 6"x 12" 7"x 14" 8"x 16" 9"x 18" 10"x 20"
WLL (ton) 2.5 3.9 5.6 7.6 9.8 12 15
Weight / ft 0.46 0.72 1.04 1.42 1.85 2.34 2.89
** All wire rope slings made with EIPS, IWRC Bright Wire rope with A1 light lube with steel ferrule and
Flemish roll splice complete with tag showing size, length, WLL and manufacture.
54
56
Wire Rope Sling Charts
Based on Design Factor = 5 and rated loads expressed in Tons (2,000 lbs)
2 Slings or Basket Hitch 2 Sling Basket Hitch 2 Sling Choker Hitch
Single Leg
60º 45º 30º 60º 45º 30º 60º 45º 30º

Vertical Choker
Horizontal Horizontal Horizontal Horizontal Horizontal Horizontal Horizontal Horizontal Horizontal
Rope Dia.
inch
1/4” 0.65 0.48 1.1 0.91 0.65 2.3 1.8 1.3 0.82 0.7 0.48
5/16” 1.0 0.74 1.7 1.4 1.0 3.5 2.8 2.0 1.3 1.1 0.74
APEX CHAIN & CABLE INC.

3/8” 1.4 1.1 2.5 2.0 1.4 4.8 4.0 2.8 1.8 1.5 1.1
7/16” 1.9 1.4 3.4 2.7 1.9 6.6 5.4 3.8 2.5 2.0 1.4
1/2” 2.5 1.9 4.4 3.6 2.5 8.7 7.1 5.0 3.2 2.7 1.9
9/16” 3.2 2.4 5.5 4.5 3.2 11 9.0 6.4 4.1 3.4 2.4
5/8” 3.9 2.9 6.8 5.5 3.9 14 11 7.8 5.0 4.1 2.9
3/4” 5.6 4.1 9.7 7.9 5.6 19 16 11 7.1 5.9 4.1
7/8” 7.6 5.6 13 11 7.6 26 22 15 9.7 8.1 5.6
1” 9.8 7.2 17 14 9.8 34 28 20 13 10 7.2
1-1/8” 12 9.1 21 17 12 42 33 24 16 13 9.1
1-1/4” 15 11 26 21 15 52 42 30 19 16 11
1-3/8” 18 13 31 25 18 62 51 36 23 19 13
1-1/2” 21 16 37 30 21 72 59 42 28 22 16
1-3/4” 28 21 49 40 28 97 79 56 37 29 21
2” 37 28 63 52 37 128 104 74 48 39 28
3 Leg Wire Rope Bridle 4 Leg Wire Rope Bridle
Rope
Dia. inch
60º Horizontal 45º Horizontal 30º Horizontal 60º Horizontal 45º Horizontal 30º Horizontal
1/4” 1.7 1.4 0.97 2.2 1.8 1.3

5/16” 2.6 2.1 1.5 3.5 2.8 2.0
3/8” 3.7 3.0 2.2 5.0 4.1 2.9
7/16” 5.0 4.1 2.9 6.7 5.5 3.9
1/2” 6.6 5.4 3.8 8.8 7.1 5.1
9/16” 8.3 6.8 4.8 11 9.0 6.4
5/8” 10 8.3 5.9 14 11 7.8
3/4” 15 12 8.4 19 16 11
7/8” 20 16 11 26 21 15
1” 26 21 15 34 28 20
1-1/8” 31 26 18 42 34 24
1-1/4” 38 31 22 51 42 30
1-3/8” 46 38 27 62 50 36
1-1/2” 55 45 32 73 60 42
1-3/4” 74 60 42 98 80 57
2” 95 78 55 127 104 73
In Accordance with ASME B30.9-2010
55
57
CAMPBELL TRANSPORT CHAIN
For use in load binding, towing and logging
In accordance with Department of Transportation regulations
Standard finish: Zinc electroplate & yellow chromate conv. To prevent the possibility of serious bodily harm:
DO NOT EXCEED the working load limits of chain or
coating
components
Standard material: Heat treated carbon steel DO NOT USE FOR OVERHEAD LIFTING OR
HOISTING
Identification markings on select links
DO NOT USE if the chain or components are visibly
distorted or worn
Transport Chain - Grade 70 -

WLL 4:1 Lin s / Wt. Lb. ID Length ID Width t / ull
Size Part Number
lbs oot / 100 (max) (min) drum
5/16 4,700 11 111 1.01” 0.48” 550 -5/1 ” 7
3/8 6,600 9 142 1.38” 0.55” 400 -3/8” 7
1/2 11,300 7 238 1.70” 0.75” 200 -1/2” 7
Compliant with National Safety Code Standard (NSC) 10 Part 1. Division 3, Section 11 (4)
Clevis Slip Hook c/w Latch

For use with Grade 70 or lower chains
Gold Chromate finish
Embossed with “OCEAN”, size & product ID for traceability
Forged Alloy steel quenched and tempered
Not for use with grade 80 chain and chain slings used in over head lifting
Dimensions (in) Weight Pcs Part
Size hain WLL lb
B P (lbs) box Number
1/4 2750 0.44 0.94 0.38 2.56 0.50 100 -1/4” S L
5/16 4300 0.50 1.06 0.44 2.87 0.75 50 -5/1 ” S L
3/8 5250 0.59 1.31 0.47 3.25 1.20 50 -3/8” S L
1/2 9000 0.75 1.69 0.63 4.00 2.80 20 -1/2” S L
Clevis Grab Hook

For use with Grade 70 or lower chains
Gold Chromate finish
Embossed with “OCEAN”, size & product ID for traceability
Forged Alloy steel quenched and tempered
Not for use with grade 80 chain and chain slings used in over head lifting
Dimensions (in) Weight Pcs
hain size WLL (lbs) Part Number
B D (lbs) box
1/4 3150 0.36 0.40 0.38 1.97 0.40 100 -1/4”
5/16 4700 0.40 0.44 0.44 2.26 0.79 50 -5/1 ”
3/8 6600 0.48 0.50 0.47 2.63 1.00 50 -3/8”
7/16 8750 0.66 0.56 0.56 2.75 1.31 40 -7/1 ”
1/2 11300 0.75 0.66 0.63 3.19 2.10 25 -1/2”
56
58
Your source in Canada for casters:
For your heavy duty applications

For your medical carts
Blue Elastic rubber casters
For special applicati on s
Grey Performa rubber casters
For all your hospital carts and beds
Light and medium duty casters
shepherd casters
For your chairs and displays
For your food and medical carts
57
57
59
Hand controlled
magnetic lifters
f Quality
A wide Choice o
MaxX 125
MaxX 250
MaxX 500
The innovative technological The operating costs are near to

concept and the superior zero, efficiency and productivity
MaxX 1000 performances make MaxX the are dramatically increased and
absolute reference in the field of the return of the investment is
magnetic lifting of ferrous loads. extremely quick.
Powerful, compact, safe, reliable The handy and practical use of

and competitive are the key MaxX lifters is possible, dew to
factors of the MaxX line’s success their compact size and limited
all over the world. weight that allows also to
optimize space and to exploit
MaxX lifters are the ideal solution crane capacity.
for handling a large variety of
MaxX 1500 work pieces, from flats to rounds, A wide range of models are
from finished to rough, with easy available with capacities ranging
and ergonomic operation in total from 125 Kg. ( 275 lbs) up to 2000
safety. Kg. (4450 lbs) and with different
versions for load with regular and
reduced thickness.
MaxX 2000
58
60
Safety Through Power
For plates
MaxX 300 E
minimum thickness 20 mm
SWL-Load (kg)
Force (daN)
Model SWL-Load Thick Length
max min. max
kg mm mm
Air gap (mm) MaxX 125 125 20 1000
MaxX 250 250 20 1500
MaxX 600 E MaxX 500 500 25 2000
minimum thickness 25 mm MaxX 1000 1000 40 3000
MaxX 1500 1500 45 3000
MaxX 2000 2000 55 3000
SWL-Load (kg)
Force (daN)
MaxX 300 E 300 20 1500

MaxX 600 E 600 25 2000
MaxX TG 150 150 8 1500

Air gap (mm) MaxX TG 300 300 10 2000
For rounds
TG
MaxX TG 150 minimum thickness 8 mm
SWL-Load (kg)
Force (daN)
Model SWL-Load Thick Length Ø

max min. max max
kg mm mm mm
MaxX 125 50 10 1000 300
MaxX 250 100 10 1500 300
MaxX 500 200 15 2000 400
Air gap (mm) MaxX 1000 400 25 3000 450
MaxX 1500 600 30 3000 500
MaxX 2000 800 35 3000 600
MaxX TG 300 minimum thickness 10 mm
MaxX 300 E 150 10 1500 300
MaxX 600 E 250 15 2000 400
SWL-Load (kg)
Force (daN)
MaxX TG 150 60 8 1500 240

MaxX TG 300 120 10 2000 290
Air gap (mm)
59
61
MANUAL CHAIN HOIST
Chain Hoist Block 619 - Meets or exceeds ASME B30.16

Capacity metric ton te 0.5 te 1 te 1.5 te 2 te 3 te 5 te 10 te
Part Number 6-0.5TCB3 6-1TCB3 6-1.5TCB3 6-2TCB3 6-3TCB3 6-5TCB3 6-10TCB3

3 m (10 ft) of Lift
Part Number 6-0.5TCB6 6-1TCB6 6-1.5TCB6 6-2TCB6 6-3TCB6 6-5TCB6 6-10TCB6
6 m (20 ft) of Lift Ea
Number of falls 1 1 1 1 2 2 4
A 131 140 161 161 161 186 207
B 127 158 174 187 199 253 398
Dimensions(mm) C 270 317 399 414 465 636 798
D 35 35.5 45 42.5 50 64 85
K 30 28 36 33.5 40 50 64
Net weight kg 10 12 19 20 27 45.5 83
Running test load Kn 7.5 15 22.5 30 45 75 150
Effort to lift rated load N 231 309 320 360 340 414 414
Load chain diameter mm 6 6 8 8 8 10 10
Chain weight kg/m kg 1.7 1.7 2.3 2.3 3.7 5.6 9.7
Standard lift from stock 3 & 6 meter – “custom chain length available on request”
Chain Hoist 619 rated in Metric Ton = Tons of 1000kgs. (or 2200 pounds or 9.81 kN)
Principle of Overload Protection
The principle of overload protection brake engagement is the same on both lever
pullers and chain blocks. The unit has an adjustable friction disk when engaged
produces a fiction force between the disk and the hand wheel or lever. This is
adjusted at the factory. Each unit is tested twice. The first is a normal proof load
test, and the second load is used to set the friction disk brake engagement. For
example on a 1.5 ton lever block, the block is pulled to 1.5 times the WLL, 1.5
ton x 1.5 = 2.25 ton as a normal proof load test. The block is then taken to 1.3
times the WLL to set the friction brake. 1.5 ton x 1.3 = 1.95 ton. If the unit is
taken above this load the friction disk will engage and the unit will not lift. Proof
loading for this block would be 1.25 x 1.5 ton = 1.875 ton
.
WARNING – READ AND UNDERSTAND ALL

WARNINGS, MAINTENANCE, AND OPERATION
INSTRUCTIONS - (SUPPLIED WITH EVERY UNIT)
60
62
LEVER CHAIN PULLERS
Lever Puller 622 Patented - Meets or exceeds ASME B30.21

Part Number 6-0.75TLP 6-1.5TLP 6-3TLP 6-6TLP 6-9TLP
each
Capacity metric tonne te 0.75 te 1.5 te 3 te 6 te 9 te

Standard lift m 1.5 1.5 1.5 1.5 1.5
Strands of load chain 1 1 1 2 3
A 148 172 200 200 200
B 90 98 115 115 115
C 136 160 180 235 320
Dimensions(mm)
H 325 380 480 620 700
L 280 410 410 410 410
K 34 38 48 52 58
Net weight kg 7 11 21 31 46
Running test load Kn 11.0 22.0 37.5 75.0 112.5
Force to lift rated load N 140 220 320 340 360
Load chain diameter mm 6 8 10 10 10
Chain weight kg/m kg 0.8 1.4 2.2 4.4 6.6
Standard Lift from stock - 1.5 meter “Custom Chain Lengths available on request”
Lever Puller 622 rated in Metric Ton = Tons of 1000kgs. (or 2200 pounds or 9.81 kN)
Principle of Overload Protection
The principle of overload protection brake engagement is the same on both lever pullers and chain blocks. The unit has an adjustable
friction disk when engaged produces a fiction force between the disk and the hand wheel or lever. This is adjusted at the factory. Each
unit is tested twice. The first is a normal proof load test, and the second load is used to set the friction disk brake engagement. For
example on a 1.5 ton lever block, the block is pulled to 1.5 times the WLL, 1.5 ton x 1.5 = 2.25 ton as a normal proof load test. The
block is then taken to 1.3 times the WLL to set the friction brake. 1.5 ton x 1.3 = 1.95 ton. If the unit is taken above this load the friction
disk will engage and the unit will not lift. Proof loading for this block would be 1.25 x 1.5 ton = 1.875 ton.
WARNINGS, MAINTANANCE, AND OPERATION
61
63
WIRE ROPE WINCH
Wire Rope Winch – c/w wire and hook

Safe, reliable, and efficient, these units are suitable for many applications.
One man operated, using a telescopic handle, they work in any position and over any height of lift.
Can replace conventional winches and other hoists for many applications.
Proof load to the WLL, and use only properly sized dry galvanized wire rope provided with units.
Spare Replacement handles

c/w std
Capacity Capacity Rope Wt. Drive
Size wire Part Number
lifting pulling dia. Kg step
length Part Number
0.8 te 1.3 te 8 mm 6 428 x 64 x 235 1 20 m 6-0.8TWRWHANDLE 6-0.8TWRW

Wire Rope Winch rated in Metric Ton = Tons of 1000kgs. (or 2200 pounds or 9.81 kN)

WARNINGS, MAINTANANCE, AND OPERATION
62
64
EXTRA RUGGED DESIGN
PROUD DISTRIBUTOR OF:
MINI AIR HOISTS

340 Henry Street, Unit #1 q Brantford, Ontario N3S 7V9 q Tel. 519-751-8085 q Fax. 519-751-8005 q www.apexchain.com
63
65
EFFICIENT, HIGH SPEED MATERIAL HANDLING
NPK air hoists are engineered to provide high lifting speeds and accurate control. Lightweight,
compact design for use in a stationary position, but can also be quickly moved to another location. Air
hoists are extremely useful in hazardous environments where electrical hoists are prohibited. Features
external brake adjustment, exhaust muffler, built-in lubricator and swivel mounted air inlet.
EXTRA RUGGED CONSTRUCTION

Durable construction for constant, heavy-duty use. Designed for fast moving production assembly
operations and heavy manufacturing industries.
OVERLOAD-PROOF AIR MOTOR FOR A WIDE SAFETY MARGIN

The rotary vane air motor is completely enclosed. Motor is unaffected by fumes, dirt, or heat. Motor
and controls can withstand constant stopping and sudden starting. Can be overloaded or stalled
without damage to the hoist. Motor is inherently self-cooling and cannot be burned out.
SAFETY HOOKS AND AUTOMATIC LIMIT STOPS

Top and bottom hooks have safety snaps and hoist has automatic limit stops to prevent over-travel.
VARIABLE SPEED CONTROL

Operator can choose any speed from the slowest creep to full throttle. The heaviest loads can be
positioned quickly and accurately, or raised rapidly. Features an external screw adjustment for lift and
descent speeds.
OPTIONAL PENDANT TYPE CONTROL

Leaves the operator with one hand free to guide the load with precise control. Preferred compact
design and easy handling. How to order model with pendant type control: RHL-250P/RHL-500P.
How to order model with standard rope control: RHL-250/RHL-500.
Model No. Capacity Ft. Of Lift No. Of Falls Headroom Lift Speed At Capacity Weight (lbs.) Rec’d Hose Size Air Inlet Thread CFM PSI
RHL-250 550 lbs. 8 1 17" 88.6 ft./min 35.2 1/2" 1/2" 45.9 90
RHL-250-10 550 lbs. 10 1 17" 88.6 ft./min 36.4 1/2" 1/2" 45.9 90
RHL-250-15 550 lbs. 15 1 17" 88.6 ft./min 39.4 1/2" 1/2" 45.9 90
RHL-250-20 550 lbs. 20 1 17" 88.6 ft./min 42.4 1/2" 1/2" 45.9 90
RHL-500 1100 lbs. 8 1 17" 41.3 ft./min 35.2 1/2" 1/2" 45.9 90
RHL-500-10 1100 lbs. 10 1 17" 41.3 ft./min 36.4 1/2" 1/2" 45.9 90
RHL-500-15 1100 lbs. 15 1 17" 41.3 ft./min 39.4 1/2" 1/2" 45.9 90
RHL-500-20 1100 lbs. 20 1 17" 41.3 ft./min 42.4 1/2" 1/2" 45.9 90
RHL-1000 2200 lbs. 8 2 20" 18.7 ft./min 48.4 1/2" 1/2” 45.9 90
RHL-1000-10 2200 lbs. 10 2 20" 18.7 ft./min 50.8 1/2" 1/2" 45.9 90
RHL-1000-15 2200 lbs. 15 2 20" 18.7 ft./min 56.8 1/2" 1/2" 45.9 90
RHL-1000-20 2200 lbs. 20 2 20" 18.7 ft./min 62.8 1/2" 1/2" 45.9 90
RHL-2800 6160 lbs. 10 2 28" 7.2 ft./min 132.0 3/4" 1/2" 60.0 90
Extra lift can be installed for an additional charge. Equipped with chain basket and pullcord standard.
Caution: This equipment is not to be used for lifting, supporting or transporting people, or for lifting or
supporting loads over people. Tool specifications are based on 90 PSI. Recommended operating air
pressure 90 PSI.
340 Henry Street, Unit #1 q Brantford, Ontario N3S 7V9 q Tel. 519-751-8085 q Fax. 519-751-8005 q www.apexchain.com
64
66
HEIGHT SAFETY EQUIPMENT
TracX Harness Line Tracpac Single Self-retracting lanyard
• Comfort & Safety Combined • Lightweight
• TracX Pad provides extra comfort and • Permanently attached to soft
minimizes weight on shoulders. pack
• Keeps you dry and comfortable with • With 3⁄4-in. (20 mm)
breathable lining. self-locking snap hook at
• Many different models available shock pack
• Available length: 6 ft. (1.8 m)
only
• E4: Capacity of 100 to 254 lbs.
(45 to 115 kg)
Tracpac Twin Self-retracting lanyard (90 to 160 kg)
• Lightweight
• Permanently attached to soft pack
• Two arms
• With 3⁄4-in. (20 mm) self-locking
snap hook at shock pack and
21⁄2-in. (64 mm) self-locking
snap hooks at each arm
• Available length: 7 ft. (2.1 m) only
(45 to 115 kg)
(90 to 160 kg)
Stopfor® S trailing rope grab
Blocfor® AES self-retracting lifeline
• New patented system with

integrated energy absorber
• Leading edge capability on
LE model
• Fiberglass filled casing for
added durability
• Fewer internal components
for added durability
• Available in different lengths
This lightweight, anticorrosive design features an independent roller

that allows the grab to travel freely on the rope. The spring-loaded,
cam-locking system insures that the grab engages during a fall.
• Spring-loaded cam-locking system
• Gravity washer to prevent upside-down installation
• Easy hinge loading anywhere on lifeline
• Stainless steel construction
• 5⁄8-in. (16 mm) three-strand rope diameter
• 3⁄4-in. (20 mm) self-locking snap hook
• Only available in E4 model with a capacity of 100 to 254 lbs. (45 to 115 kg)
65
67
Tracpode confined space systems
• Desgined to provide a safe means of accessing a confined space area
• Allow rescuers to retrieve injured or unconscious workers without exposing themselves to similar potention hazards.
• Available integrated in different system kits or alone.
Portable anchor wedges

Reusable concrete anchor connector
• For fall protection
• Breaking strength: 5,000 lbs. (22.2 kN), 10,000 lbs. (44.4 kN)
• Also works with steel
• For construction or industrial use
Lifelines
Bulk Kermantle lifelines
• 7⁄16-in. (11 mm) diameter
• Breaking strength: 8,000 lbs. (35.6 kN) Tie-back anchors
Polyblend lifelines
• Breaking strength: 10,000 lbs. (44.4 kN)
Superline lifelines
Breaking strength: 6,500 lbs. (28.9 kN)
Breaking strength: 11,500 lbs. (51.2 kN)
U-bar Wall mounted Flush

The standard U-bar safety When tie-backs are required on An ideal solution when no
tie-back anchors are the roofs where waterproofing or protrusions on the roof are
economical solution for securing flashing is not an option, permissible.
safety lifelines or equipment Tractel®'s wall-mounted U-bar
lines for fall protection and tie-back anchors provide a
suspended work. simple, inexpensive solution.
66
68
Lifting Specialists & Consultants
All products & services recommended or designed by APEX CHAIN AND
CABLE Inc. meet MOL and ASME/ANSI Standards for “Below the Hook Lifting
Devices”
ALLOY CHAIN SLINGS

Welded on mechanical assemblies – Standard or adjustable
Custom or specialized to meet specific applications
CHAIN
All types – Welded & weld less – Low carbon – High-test – Transport – Alloy – Stainless
General & special application – Assemblies – Tie down – Windless
CUSTOM FABRICATED LIFTING DEVICES

All types – Custom engineered to meet specific applications designed by professional engineers to meet or exceed
ANSI/ASME and government standards including PSR if required.
Proof tested and certified
MAGNETS
Permanent – Electro permanent – Battery powered
220–4,400 lbs – 600-20,000 lbs – 2,500-15,000 lbs
Flat bar – Angle iron – Rounds
PLATE CLAMPS
IP - Merrill - Renfroe- Safety - Clamp - Super Clamp
Vertical – Horizontal – Beam – Girder – Non-marring – Spec application
SPREADER BEAMS & FRAMES

Single purpose to multi-purpose – Adjustable – Rotating
Manual – Powered – Custom designed & engineered to meet specific requirements
Tested & Certified
SYNTHETIC SAFETY CORE FLATWEB SLINGS

Nylon & polyester – 1” to 16” width – 1 Ply to 4 ply
Mfg to web sling & tie down standard class 7 H.D.
SYNTHETIC ROUNDSLINGS (DOUBLE COVER)

Polyester & K-spec – Single round – Twin path flat
TESTING
Proof testing – Proof testing & certification
Specialists in testing below-the-hook lifting devices
New, existing or repaired lifters, MPI Inspection to meet Dept. of Labour, ANSI/ASME, OSHA and provincial regulation
WIRE ROPE
Domestic – Imported
Specialty ropes – Slings – Custom assemblies
INSPECTION & SAFETY SEMINARS

INPLANT INSPECTION: Recorded inspection of all below-the-hook lifting devices to meet Dept. of Labour & ASME/ANSI
requirements & standards.
SAFETY SEMINAR: A (non selling) slide & video presentation showing actual in plant applications of do’s and don’ts
including how to visually inspect as required before each lift.
INSPECTOR TRAINING: An 8 hour intense training course covering the inspection and recording of all types of below-
the-hook lifting devices. Conducted 3-4 times per year.
58
67
69

Apex Revision June

Uploaded by

Copyright:

Available Formats

Apex Revision June

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Apex Revision June

Uploaded by

Copyright:

Available Formats

RIGGING GUIDE &

340 Henry St. Tel: 519-751-8085

PRODUCT LINE CARD

ACTEK MFG. IMPERIAL & METRIC HOIST RINGS

BUDGIT CHAIN & WIRE ROPE HOISTS

CAMPBELL CHAIN, SLINGS, COMPONENTS

CAN-AM CASTERS / COLSON FULL LINE OF CUSTOM QUALITY CASTERS

CARR-LANE JIG & FIXTURE TOOLING COMPONENTS

COLUMBUS McKINNON CHAIN PULLERS, HOISTS & ALLOY COMPONENTS

CROSBY SHACKLES, WIRE ROPE FITTINGS, HOIST RINGS,

GLEASON REEL HOSE & CABLE REELS

APEX RIGGING COMPONENT CHAIN SLINGS, CRANE CABLES,

APEX SYNTHETIC SLINGS NYLON, POLYESTER, BALLISTIC, AND ROUND SLINGS

INTER-PRODUCT / RENFROE / MERRILL LIFTING CLAMPS

IGUS POWER TRACK & IGLIDE

SERVICES: CERTIFICATION / PROOFTESTING CERTIFICATION AND PROOFTESTING OF DEVICES

CERTIFIED CUSTOM DEVICES SPECIALIZED LIFTING COMPONENTS

LIFT ALL MESH SLINGS, LOAD HUGGERS

McKISSICK SHEAVES & BLOCKS

TECNOMAGNETE PERMANENT LIFTING MAGNETS AND WORK HOLDING

TRACTEL FALL ARREST, LOAD MEASURE EQUIPMENT

STAINLESS STEEL FITTINGS, WIRE ROPE, CUSTOM ASSEMBLIES

YOKE ALLOY CHAIN COMPONENTS

THERN WINCH SPECIALISTS

***DELIVERED TO YOU BY OUR TRAINED PROFESSIONALS***

***COMPLETE CATALOGS AVAILABLE UPON REQUEST***

HOW TO ORDER SLINGS

Vertical Choker Basket

Maximum weight to be lifting

Determine the type of webbing you will use

Order using part numbers

Sling Type Ply Webbing Width Length Type

GOOD BETTER BEST

Edge wrap wear pad is sewn along

Angle Strength Loss From Rated Capacity

Angle Angle CAUTION: SLING SHOULD FIT THE HOOK

Remove the sling from service is any of the following is visible:

TYPE 1 TRIANGLE - CHOKER

SINGLE PLY DOUBLE PLY

WARNING MAXIMUM RATED CAPACITIES FOR NEW SLINGS. DO NOT EXCEED

TYPE 2 TRIANGLE - TRIANGLE

Type 2 (TT) slings have a steel triangle fitting on each

SINGLE PLY DOUBLE PLY

WARNING MAXIMUM RATED CAPACITIES FOR NEW SLINGS. DO NOT EXCEED

TYPE 3 & 4 - EYE & EYE

SINGLE PLY DOUBLE PLY

WARNING MAXIMUM RATED CAPACITIES FOR NEW SLINGS. DO NOT EXCEED

TYPE 5 Type 5 (EN) endless slings the webbing is overlapped to form

SINGLE PLY DOUBLE PLY

WARNING MAXIMUM RATED CAPACITIES FOR NEW SLINGS. DO NOT EXCEED

SINGLE PLY DOUBLE PLY

WARNING MAXIMUM RATED CAPACITIES FOR NEW SLINGS. DO NOT EXCEED

TYPE 7 EYE & EYE

SINGLE PLY DOUBLE PLY

WIDE LIFT CARGO SLINGS

SINGLE PLY DOUBLE PLY

WARNING MAXIMUM RATED CAPACITIES FOR NEW SLINGS. DO NOT EXCEED

BRIDLE LEG SLINGS

WARNING MAXIMUM RATED CAPACITIES FOR NEW SLINGS. DO NOT EXCEED

EXTRA EYES are available in QUICK DISCONNECTS allow for

DELIVERED TO YOU BY OUR TRAINED PROFESSIONALS

COMPLETE CATALOGS AVAILABLE UPON REQUEST