Scribd
Upload
51 views7 pages

3G Failover With DSL On DG BG4300NU IS

This document provides steps to configure a DG-BG4300NU/IS router in 3G failover mode with a DSL internet connection. The steps include: 1) Connecting a 3G/4G dongle to the router and checking the connection. 2) Accessing the router's configuration page and enabling the 3G WAN settings. 3) Verifying the dongle status shows as connected. 4) Configuring the router for a PPPoE DSL connection, providing the ISP login details. 5) The router will now failover to the 3G connection if the DSL link goes down.

Uploaded by

chad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
51 views7 pages

3G Failover With DSL On DG BG4300NU IS

This document provides steps to configure a DG-BG4300NU/IS router in 3G failover mode with a DSL internet connection. The steps include: 1) Connecting a 3G/4G dongle to the router and checking the connection. 2) Accessing the router's configuration page and enabling the 3G WAN settings. 3) Verifying the dongle status shows as connected. 4) Configuring the router for a PPPoE DSL connection, providing the ISP login details. 5) The router will now failover to the 3G connection if the DSL link goes down.

Uploaded by

chad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

HOW TO CONFIGURE DG-BG4300NU/IS IN 3G FAILOVER MODE WITH DSL LINE

STEP 1: CONNECT DONGLE TO ROUTER

Make sure the internet is working from Dongle first


After connecting it to router, check with the USB led on the router

STEP 2: ACCESSING THE WEB CONFIGURATION PAGE INSIDE THE ROUTER

Open the configuration page of the router by typing http://192.168.1.1 in a web browser. We recommend this one time
configuration to be done using Internet Explorer.

Enter the username as admin and password as admin and click on OK.
STEP 3: CONFIGURE WAN 3G SETTINGS

Click on Setup >> WAN. Then click on 3G/4G on the left hand side.

3G/4G WAN : Enable


Network Type : Auto
APN : According to the ISP ( Ex : For Jio Sim: jionet )
Dial Number : *99#
3G to WAN Switch Over Time(s) : 10
Check the WAN 3G Connections Table
Click on Apply Changes.

STEP 4: CHECK THE DONGLE STATUS

Status >> 3G/4G Info

Signal Strength
Connection Status : Connected
Sim Card Status : Sim Ready

Now verify the internet access through DG-BG4300NU/IS router.


STEP 5: CONFIGURE THE ROUTER IN PPPOE MODE

Click on Setup > WAN


First delete the entry in WAN Interface Table which is at bottom of the page
WAN Physical Type > Select ADSL WAN
Enter VPI and VCI values as provided by the ISP ( For Ex : For BSNL, VPI – 0 and VCI – 35)
Channel Mode : PPPoE
Enter Username and Password provided by the ISP

VPI, VCI depends on ISP


Username/password as provided by ISP

Scroll to the end of the page, till you see the WAN Interfaces Table.
Refresh and reboot the router.
STEP 6: CHECK THE DSL STATUS

Status >> Device Info >> ADSL WAN Interface Table.


In this case ADSL WAN will be primary WAN by default. In case the DSL link goes down, the router will auto-switch to 3G/4G mode.
Dongle status will get disconnected once the ADSL link is On.

You might also like