INSTRUCTION MANUAL

DIAGNOSTIC TESTER

Diagnostic tester

Instruction Manual
Software
ENGLISH

Prepared by: Sylwester Czupryna

Approved by: Sebastian Żur
ElproSys Sp. z o.o.
ul. Tarnogórska 140
44-102 Gliwice

1
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

1 LEGAL RESERVATIONS AND AGREEMENT OF USE 3

2 MENU NAVIGATION ( MULTI-TOUCH SCREEN) 4

3 MAIN SCREEN 5

4 KEYPAD 6

5 MENU ICONS – DESCRIPTION 6

6 SETUP 7

7 SUBMENU INFORMATION 8

8 SUBMENU TESTS 8

9 TOOLS 9

10 MENU – SUBJECT OF PROGRAMMING 10

11 EXEMPLARY PROGRAMMING 11

12 BASIC SETTINGS 12

13 DIAGPROG4 MANUAL UPDATE 14

14 MAINTENANCE 14

15 DISPLAY FIRMWARE UPDATE 15

16 RESTART DIAGPROG4 15

17 DIAGPROG4 MANAGER 16

18 DESCRIPTIVE MENU 17

2
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

1 LEGAL RESERVATIONS AND AGREEMENT OF USE

Once Diagprog4 device is switched on user should select language from the supported languages list.
Language selection will result in the change of language in the entire menu.

User should review LEGAL RESERVATIONS and AGREEMENT OF USE. By selecting the Agree – accept
button user accepts AGREEMENT OF USE and Diagprog4 device will switch on.

It is necessary to accept AGREEMENT OF USE each time device is switched on.

3
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

2 MENU NAVIGATION ( MULTI-TOUCH SCREEN)

Simple gestures — tapping or pressing with fingers — is enough to select menu options.

In order to navigate the menu using keypad press Accept button to activate it and fully use
keypad.

- Accept, - Cancel, - Top, - Bottom

4
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

3 MAIN SCREEN
To navigate the main screen please use main screen icons or top/bottom buttons on the keypad.

MAIN SCREEN ICONS

ICONS FUNCTION

Cars Selection of a car model

Motorbikes Selection of a motorbike model

Other Selection of a quad, scooter, tractor model

Tools Basic Tools

Setup Basic Setup

Information Information about Diagprog4

Special programs Runs special/diagnostic functions

VIN programs Read car’s VIN numer. Car selection based on VIN number.

Accept Icon Allows to accept

Cancel Icon Allows to cancel

Top Icon Allows to MOVE UPWARDS in the menu

Bottom Icon Allows to MOVE DOWNWARDS in the menu

5
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

4 KEYPAD
Keypad below the multi-touch screen is another way to navigate DiagProg4 menu.

KEYPAD – BUTTONS

BUTTONS FUNCTION
Accept Button Button to ACCEPT

Cancel Button Button to CANCEL

Top Button Button to MOVE UPWARDS in the menu

Bottom Button Button to MOVE DOWNWARDS in the menu

5 MENU ICONS – DESCRIPTION

Example of MENU

DIAGNOSTICS EEPROM READ/WRITE

SERVICES – ADVANCED EDITING FLASH READ/WRITE

DIAGNOSTICS AND REPAIR OF CAR

ADVANCED DIAGNOSTIC FUNCTIONS
MODULES
IMMOBILIZER FUNCTIONS FOR ADVANCED USERS

CLEAR CRASH DATA

MENU ICONS – description

DIAGNOSTICS Automotive diagnostics e.g. read and

clear trouble codes DTC, service, module
identification.
SERVICES – ADVANCED EDITING Service inspection - reading, writing,
editing
DIAGNOSTICS AND REPAIR OF CAR MODULES Option diagnostics and repair of car
modules
IMMOBILIZER Immobilizer
CLEAR CRASH DATA Clearing accident data
EEPROM READ/WRITE Reading and writing EEPROM content
FLASH READ/WRITE Reading and writing FLASH content
ADVANCED DIAGNOSTIC FUNCTIONS Advanced diagnostic functions
FUNCTIONS FOR ADVANCED USERS Functions for advanced users

6
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

6 SETUP
SETUP MENU FEATURES

ICON DESCRIPTION
ACTIVE TECHNICAL SUPPORT Provides access to all data sent automatically to seek active
technical support
DEFAULT SETTINGS Restoring the device to the original state once initially used

DOWNLOAD UPDATE/ ACTIVATION Allows user to check for new updates/ activations

INFORMATION Information about DiagProg4

LANGUAGE Menu language selection: Polish, English, German, French, Italian,

Spanish, Portuguese, Brazilian
MAINTENANCE File synchronisation between device and files on the server
OBDII/VOLTAGE TEST SETTINGS Power supply to connected module and OBDII connector

OTHER SETTINGS Settings modification: e.g. contrast, volume

POWER SAVING Switch ON/OFF screensaver

SECURITY DiagProg4 additional security measures

TESTS Tests available for the user
WIFI SETTINGS WIFI settings modification

7
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

7 SUBMENU INFORMATION

ABOUT DIAGPROG4 Information about DiagProg4

CONTROL NUMBER Used for registration in customer zone at www.diagprog4.com
DATE/TIME Information about date and time
DEVICE LIMITS Information about DiagProg4 limits
AGREEMENT OF USE Information about DiagProg4 Agreement of Use
IMPORT DP3 LICENSES Allows to transfer all active programs from Diagprog3 to
Diagprog4
OPEN-SOURCE LICENSE Information about Open-Source license DiagProg4

8 SUBMENU TESTS

EXTERNAL INTERFACE TEST External interface test

CHECK SDHC CARD FAT32 SYSTEM Micro SDHC card compatibility with FAT32 system test
MULTIPLEX TEST MULTIPLEX test

8
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

9 TOOLS

ICON DESCRIPTION
CAN ANALYZER (Internal use only) Programs For Internal Use Only
CAN PLAYER (Internal use only) Programs For Internal Use Only
CAN TERMINATION CONTROL Enables/ disables High Speed CAN Termination
DOWNLOAD UPDATE/ ACTIVATION Allows user to check for new updates/ activations

EEPROM PROGRAMMER Write EEPROM memory

EXTERNAL UNIT POWER Power supply to connected module
HEXEDITOR File editing in hexadecimal system
J1850 ANALYZER (Internal use only) Programs For Internal Use Only
K-L ANALYZER (Internal use only) Programs For Internal Use Only
MICROCONTROLLER PROGRAMMER Write FLASH + EEPROM
RESTART DIAGPROG4 Immediate restart in order to reload operating system
RESTORE THE BACKUP MODULE Restore backup file saved on SD card
SENDING LOG FILE Send *.LOG file to ElproSys server for technical support
SUPPORT SCRIPT Runs support script prepared for user by technical support team
UDS COMMUNICATION CONTROL Enables/ disables UDS communication
UNIT CALCULATOR Enables metric conversion

9
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

10 MENU – SUBJECT OF PROGRAMMING

Menu – Subject of programming can be Menu for CARS, MOTORBIKES and OTHER VEHICLES.

EXEMPLARY PROGRAMMING MENU

10
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

11 EXEMPLARY PROGRAMMING
Exemplary programming of Alfa Romeo \ 146/146 \ ST5249

MENU FOR BRAND SELECTION MENU FOR MODEL SELECTION

MENU FOR MODULE SELECTION MENU FOR THE TYPE OF PROGRAMMING SELECTION

11
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

12 BASIC SETTINGS

WIFI settings

Select SETUP , next select WIFI settings from the menu and connect to WIFI network.

Select available WIFI network and enter If WIFI network connection is correct then
password. information about network will be displayed
next time WIFI SETTINGS are selected until the
device

is disconnected from the network.

Information about WIFI enabled by default is stored on SD card. Without SD card device will not
remember WiFi network.

LANGUAGE settings

Select SETUP , next select LANGUAGE from the menu and accept with OK button.

12
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

SENDING LOG FILE

If any error occurs during module programming DiagProg4 sends LOG file to ElproSys server for
Technical Support.

SENDING LOG FILE MANUALLY

Select TOOLS , next select SENDING LOG FILE from the menu.

Sending LOG file is only possible when device is within WIFI network range.

If LOG file is sent successfully message will be displayed on the screen.

LOG file can be sent using dedicated software - DiagProg4 Manager.

13
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

13 DIAGPROG4 MANUAL UPDATE

Connect DiagProg4 to PC via mini USB cable (Linux, Unix, MAC OS, Android or Windows), it will
appear as an additional external drive.

Save update.dpu file, received directly from ElproSys or its representative in the main folder of
microSDHC card and restart the device which will be automatically updated.

DiagProg4 can be updated using dedicated software - DiagProg4 Manager.

14 MAINTENANCE
MAINTENANCE enables remote maintenance of the device in order to ensure optimal technical
parameters.

Once MAINTANANCE option is selected device will automatically run microSDHC card test and will
synchronize files with Elprosys server. Before you start make sure to:
- insert microSDHC card
- connect DP4 to WIFI network (Internet)

File synchronisation can be completed using dedicated software - DiagProg4

Manager.

14
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

15 DISPLAY FIRMWARE UPDATE

Display firmware update is downloaded automatically.
User has to select from DP4 menu:

SETUP → OTHER SETTINGS → TFT Update

Estimated installation time : around 1 minute

IMPORTANT: Do not turn off power supply before finishing update.

16 RESTART DIAGPROG4
If the device screen does not respond to touch, it is possible to restart it to restore its efficiency.
Press and hold buttons - up and - cancel for at least 3 seconds to restart DiagProg4 device.

15
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

17 DIAGPROG4 MANAGER
DIAGPROG4 MANAGER – PC tool
DIAGPROG4 MANAGER connects DiagProg4 with PC, allowing data synchronisation between devices.
Software used to manage device using PC.

DiagProg4 connection with PC:

It is required to use mini USB cable supplied by manufacturer in order to connect DiagProg4 with PC.
DiagProg4 should be connected to an additional power source.

Software update Use this option to download latest update and

activations from Elprosys server.

File synchronization Use this option to download necessary data files

(BSI, Flash, etc.) from Elprosys server

Technical support Use this option to send data - like LOG file,
activation status etc. required to seek technical
support
MicroSD card manager Use this option to view memory card data

Info about DiagProg4 Use this option to view device details

Info about DiagProg4 Manager Use this option to view information about
DiagProg4 Manager

16
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

System requirements:
Operating system: Windows Vista, Windows 7, Windows 8, Windows 10.
RAM: 1 GB (Recommended)
Free disk space: At least 2 GB (Recommended)
Software requirements: .Net Framework 4.5 or above

18 DESCRIPTIVE MENU
Some DiagProg4 functions will show additional hints. When a position is selected from the menu
device will display additional descriptive menu. In order to display hint select a position from the
menu, press it and hold it.

17
©Elprosys
April 2019 − Rev. 3.1
 INSTRUCTION MANUAL
DIAGNOSTIC TESTER

RECORD OF CHANGES

Date Author Changes

03.03.2016 Czupryna Sylwester Adding LEGAL RESERVATIONS and AGREEMENT OF USE

03.03.2016 Czupryna Sylwester Software number (SN) is displayed on the main screen.
03.03.2016 Czupryna Sylwester New „DIAG” icon replacing „VIN” icon on the main screen
03.03.2016 Czupryna Sylwester Change in SETUP MENU – adding new positions:
- MAINTENANCE
- OBDII/VOLTAGE TEST SETTINGS
03.03.2016 Czupryna Sylwester Change in SUBMENU INFORMATION – adding new positions:
- CONTROL NUMBER
- AGREEMENT OF USE
- DP3 LICENSES IMPORT
- OPEN-SOURCE LICENSE
03.03.2016 Czupryna Sylwester Change in TOOLS MENU – adding new positions:
- SENDING LOG FILE
- RESTART DIAGPROG4
03.03.2016 Czupryna Sylwester Adding description for option: SENDING LOG FILE manually
03.03.2016 Czupryna Sylwester Adding description for option: MAINTANANCE
03.03.2016 Czupryna Sylwester Adding description for option: RESTART DIAGPROG4
03.03.2016 Czupryna Sylwester Adding description for option: DESCRIPTIVE MENU
Change in TOOLS MENU – adding new positions:
- DOWNLOAD UPDATE/ ACTIVATION
03.04.2017 Czupryna Sylwester
- SUPPORT SCRIPT
- UDS COMMUNICATION CONTROL
03.04.2017 Czupryna Sylwester Hardware version is displayed on the main screen.
03.04.2017 Czupryna Sylwester Adding additional language: Brazilian
03.04.2017 Czupryna Sylwester Adding DISPLAY FIRMWARE UPDATE
03.04.2017 Czupryna Sylwester Adding DIAGPROG4 MANAGER – PC tool
07.02.2019 Czupryna Sylwester Display firmware update
20.03.2019 Czupryna Sylwester Change in programming menu

18
©Elprosys
April 2019 − Rev. 3.1