Warning Chime System: Section

DRIVER INFORMATION & MULTIMEDIA
WCS
A
B
SECTION
WARNING CHIME SYSTEM C
E
CONTENTS
PRECAUTION ............................................... 3 DIAGNOSIS SYSTEM (BCM) ........................... 23 F
PRECAUTIONS ................................................... 3 COMMON ITEM (WITH INTELLIGENT KEY SYS-

Precaution for Supplemental Restraint System TEM) ...........................................................................23
G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- COMMON ITEM (WITH INTELLIGENT KEY SYS-
SIONER" ................................................................... 3 TEM) : CONSULT Function (BCM - COMMON
Precautions Necessary for Steering Wheel Rota- ITEM) (With Intelligent Key) .....................................23
H
tion After Battery Disconnection ................................ 3
COMMON ITEM (WITHOUT INTELLIGENT KEY
SYSTEM DESCRIPTION .............................. 4 SYSTEM) ....................................................................24
COMMON ITEM (WITHOUT INTELLIGENT KEY
I
COMPONENT PARTS ........................................ 4 SYSTEM) : CONSULT Function (BCM - COM-
Component Parts Location ........................................ 4 MON ITEM) (Without Intelligent Key) ......................24
Combination Meter .................................................... 4
BUZZER (WITH INTELLIGENT KEY) .......................25 J
SYSTEM .............................................................. 6 BUZZER (WITH INTELLIGENT KEY) : CONSULT
Function (BCM - BUZZER) ......................................25
WARNING CHIME SYSTEM ....................................... 6
BUZZER (WITHOUT INTELLIGENT KEY) ................26 K
WARNING CHIME SYSTEM : System Description
...... 6 BUZZER (WITHOUT INTELLIGENT KEY) : CON-
WARNING CHIME SYSTEM : Fail-Safe ................... 7 SULT Function (BCM - BUZZER) ............................26
L
WARNING CHIME ....................................................... 7 ECU DIAGNOSIS INFORMATION .............. 27
WARNING CHIME : Light Reminder Warning .......... 7
WARNING CHIME : Parking Brake Release COMBINATION METER (WITH INTELLI-
GENT KEY SYSTEM) ....................................... 27 M
Warning Chime ......................................................... 8
WARNING CHIME : Seat Belt Warning .................... 9 Reference Value ......................................................27
Fail-Safe ..................................................................32
DIAGNOSIS SYSTEM (COMBINATION DTC Inspection Priority Chart ..................................33 WCS
METER) ..............................................................11 DTC Index ...............................................................33
WITH COLOR INFORMATION DISPLAY ................. 11 COMBINATION METER (COLOR DISPLAY

WITH COLOR INFORMATION DISPLAY : On O
MODELS WITHOUT INTELLIGENT KEY) ....... 35
Board Diagnosis Function ....................................... 11
WITH COLOR INFORMATION DISPLAY : CON- EXCEPT BCM FUNCTION ........................................35
SULT Function (METER/M&A) ............................... 14 EXCEPT BCM FUNCTION : Reference Value ........35 P
EXCEPT BCM FUNCTION : Fail-Safe ....................39
WITH MONOCHROME INFORMATION DISPLAY.... 17 EXCEPT BCM FUNCTION : DTC Inspection Pri-
WITH MONOCHROME INFORMATION DIS- ority Chart ................................................................40
PLAY : On Board Diagnosis Function ..................... 17 EXCEPT BCM FUNCTION : DTC Index .................40
WITH MONOCHROME INFORMATION DIS-
PLAY : CONSULT Function (METER/M&A) ........... 19
Revision: November 2016 WCS-1 2017 D23

COMBINATION METER (MONOCHROME BCM (BODY CONTROL SYSTEM) (WITH INTEL-
DISPLAY MODELS WITHOUT INTELLIGENT LIGENT KEY SYSTEM) ............................................ 74
KEY) ................................................................... 42 BCM (BODY CONTROL SYSTEM) (WITH INTEL-
LIGENT KEY SYSTEM) : Diagnosis Procedure ..... 74
EXCEPT BCM FUNCTION ........................................ 42
EXCEPT BCM FUNCTION : Reference Value ....... 42 BCM (BODY CONTROL SYSTEM) (WITHOUT IN-
EXCEPT BCM FUNCTION : Fail-Safe ................... 47 TELLIGENT KEY SYSTEM) ...................................... 75
EXCEPT BCM FUNCTION : DTC Inspection Pri- BCM (BODY CONTROL SYSTEM) (WITHOUT
ority Chart ............................................................... 48 INTELLIGENT KEY SYSTEM) : Diagnosis Proce-
EXCEPT BCM FUNCTION : DTC Index ................. 48 dure ......................................................................... 75
BCM ................................................................... 49 METER BUZZER CIRCUIT ............................... 78

List of ECU Reference ............................................ 49 Component Function Check ................................... 78
Diagnosis Procedure .............................................. 78
WIRING DIAGRAM ..................................... 50
PARKING BRAKE SWITCH SIGNAL CIR-
WARNING CHIME SYSTEM ............................. 50 CUIT ................................................................... 79
Wiring Diagram - (with Color Display and Intelli- Component Function Check ................................... 79
gent Key System) ................................................... 50 Diagnosis Procedure ............................................... 79
Wiring Diagram - (with Color Display and without Component Inspection ............................................ 80
Intelligent Key System) ........................................... 56
Wiring Diagram - (with Monochrome Display) ........ 62 SEAT BELT BUCKLE SWITCH SIGNAL CIR-
CUIT ................................................................... 81
BASIC INSPECTION ................................... 70 Component Function Check .................................. 81
Diagnosis Procedure .............................................. 81
DIAGNOSIS AND REPAIR WORKFLOW ......... 70 Component Inspection ............................................ 83
Work Flow ............................................................... 70
SYMPTOM DIAGNOSIS ............................ 84
DTC/CIRCUIT DIAGNOSIS ......................... 72
THE PARKING BRAKE RELEASE WARNING
POWER SUPPLY AND GROUND CIRCUIT ..... 72 CONTINUES SOUNDING, OR DOES NOT
COMBINATION METER (WITH INTELLIGENT SOUND .............................................................. 84
KEY SYSTEM) .......................................................... 72 MODELS WITH ABS ................................................. 84
COMBINATION METER (WITH INTELLIGENT MODELS WITH ABS : Description ......................... 84
KEY SYSTEM) : Diagnosis Procedure ................... 72 MODELS WITH ABS : Diagnosis Procedure .......... 84
COMBINATION METER (COLOR DISPLAY MOD-
MODELS WITHOUT ABS ......................................... 84
ELS WITHOUT INTELLIGENT KEY) ........................ 72 MODELS WITHOUT ABS : Description .................. 84
COMBINATION METER (COLOR DISPLAY MODELS WITHOUT ABS : Diagnosis Procedure... 84
MODELS WITHOUT INTELLIGENT KEY) : Diag-
nosis Procedure ...................................................... 72 THE LIGHT REMINDER WARNING DOES
COMBINATION METER (MONOCHROME DIS-
NOT SOUND ...................................................... 86
Description .............................................................. 86
PLAY MODELS WITHOUT INTELLIGENT KEY) ..... 73
Diagnosis Procedure ............................................... 86
COMBINATION METER (MONOCHROME DIS-
PLAY MODELS WITHOUT INTELLIGENT KEY) : THE SEAT BELT WARNING CONTINUES
Diagnosis Procedure .............................................. 73 SOUNDING, OR DOES NOT SOUND ............... 87
Description .............................................................. 87
Diagnosis Procedure ............................................... 87

PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000014655543
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING: D
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, it is recommended that all mainte-
nance and repair be performed by an authorized NISSAN/INFINITI dealer. E
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury
caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,
see the SR section.
F
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the H
Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the I
battery or batteries, and wait at least three minutes before performing any service.
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection
INFOID:0000000014584466
J
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
K
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables. L
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and M
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
WCS
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE: O
Supply power using jumper cables if battery is discharged.
2. Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
P
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT.

COMPONENT PARTS
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location INFOID:0000000014250262
AWNIA4474ZZ
Transmission assembly (M/T without

A.
ABS models)
No. Component Function

1. Parking brake switch Transmits a parking brake switch signal to the combination meter.
• Based on the signals received from various units and switches, transmits the buzzer output sig-
nal to the combination meter via CAN communication (with Intelligent Key system).
2. BCM
• Refer to BCS-7, "BODY CONTROL SYSTEM : Component Parts Location" (with Intelligent Key
system) for detailed installation location.
• Transmits the vehicle speed signal to the combination meter via CAN communication.
ABS actuator and electric
3. • Refer to BRC-116, "Component Parts Location" (with VDC), or BRC-11, "Component Parts Lo-
unit (control unit)
cation" (without VDC) for detailed installation location.
• Controls the parking brake release warning chime with the vehicle speed signal received from
ABS actuator and electric unit (control unit) via CAN communication and the parking brake
switch signal from parking brake switch (with ABS).
4. Combination meter
• Controls the parking brake release warning chime with the vehicle speed sensor signal received
from vehicle speed sensor and the parking brake switch signal from parking brake switch (with-
out ABS).
5. Seat belt buckle switch LH Transmits seat belt buckle switch LH signal to the combination meter.
6. Vehicle speed sensor Transmits a vehicle speed sensor signal to the combination meter (without ABS).
Combination Meter INFOID:0000000014250263
The combination meter sounds the following warnings, according to signals from each switch and unit:
• Light reminder warning
• Parking brake release warning chime

COMPONENT PARTS
• Seat belt warning
A
With Color Display
The combination meter has a built-in buzzer (1).
D
JSNIA7596ZZ
With Monochrome Display E

The combination meter has a built-in buzzer (1).
H
JSNIA7597ZZ
WCS

SYSTEM
SYSTEM
WARNING CHIME SYSTEM
WARNING CHIME SYSTEM : System Description INFOID:0000000014250264
SYSTEM DIAGRAM
With Intelligent Key System
AWNIA4475GB
Without Intelligent Key System
AWNIA4476GB
DESCRIPTION
Combination Meter:
The combination meter sounds the alarm buzzer installed in the combination meter when receiving the buzzer
output signal transmitted from each unit.
BCM:
BCM receives signals from various units and transmits a buzzer output signal to the combination meter via
CAN communication if it judges that the warning buzzer should be activated.
WARNING CHIME FUNCTION LIST
Warning functions Refer to

Light reminder warning WCS-7, "WARNING CHIME : Light Reminder Warning"
WCS-8, "WARNING CHIME : Parking Brake Release Warning
Parking brake release warning chime
Chime"
Seat belt warning WCS-9, "WARNING CHIME : Seat Belt Warning"

SYSTEM
WARNING CHIME SYSTEM : Fail-Safe INFOID:0000000014250265
A
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
Function Specifications B
Buzzer The buzzer turns OFF by suspending communication.
WARNING CHIME
C
WARNING CHIME : Light Reminder Warning INFOID:0000000014250266
SYSTEM DIAGRAM D
With Intelligent Key system
G
AWNIA4058GB
Without Intelligent Key system H
AWNIA4059GB
K
WARNING CHIME OPERATION CONDITIONS
If all of the following conditions are fulfilled:
L
Operation conditions
Ignition switch OFF
M
Combination switch (Lighting switch) 1st or 2nd position
Driver side door Open [front door switch LH ON]
WARNING CHIME CANCEL CONDITIONS WCS

Warning is canceled if any of the following conditions are fulfilled:
O
Ignition switch ON
Combination switch (Lighting switch) OFF or AUTO position P
Driver side door Close [front door switch LH OFF]
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges light reminder warning chime is
necessary from signals below.

SYSTEM
Signal name Signal source

Ignition switch signal —
Combination switch signal Combination switch (Lighting switch) BCM
Driver door switch signal Front door switch LH BCM
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
Buzzer output signal BCM Combination meter
Without Intelligent Key system
Buzzer output signal BCM Meter control unit
WARNING CHIME : Parking Brake Release Warning Chime INFOID:0000000014250267
SYSTEM DIAGRAM
(Models with ABS)
AWNIA2578GB
(Models without ABS)
JSNIA2932GB
WARNING OPERATION CONDITIONS

Ignition switch ON
Parking brake During the operation (parking brake switch ON).
Vehicle speed Approximately 4.3 MPH (7 km/h) or more.
WARNING CANCEL CONDITIONS

SYSTEM
A
Ignition switch OFF
B
Parking brake Release condition (parking brake switch OFF).
Vehicle speed Approximately 1.9 MPH (3 km/h) or less.
SIGNAL PATH C
Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.
D
E
Parking brake switch signal Parking brake switch Combination meter
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter F
Vehicle speed sensor signal Vehicle speed sensor (without ABS) Combination meter
G
WARNING CHIME : Seat Belt Warning INFOID:0000000014577679
SYSTEM DIAGRAM H
K
AWNIA4477GB
Without Intelligent Key system L
WCS
AWNIA4478GB O
WARNING OPERATION CONDITIONS
P
Ignition switch ON
Seat belt buckle switch LH Unfastened (seat belt buckle switch LH ON)
WARNING CANCEL CONDITIONS


SYSTEM
Ignition switch OFF
Seat belt buckle switch LH Fastened (seat belt buckle switch LH OFF)
6 seconds after the start of warning sound
SIGNAL PATH
1. BCM requires warning chime output to combination meter, when it judges seat belt warning chime is nec-
essary from signals below.

Seat belt buckle switch LH signal Seat belt buckle switch LH Combination meter BCM
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
Buzzer output signal BCM Combination meter

DIAGNOSIS SYSTEM (COMBINATION METER)
A
WITH COLOR INFORMATION DISPLAY
WITH COLOR INFORMATION DISPLAY : On Board Diagnosis Function INFOID:0000000014584483
B
ON BOARD DIAGNOSIS ITEM
The following meter functions can be checked during Combination Meter Self-Diagnosis Mode:
• Pointer sweep of speedometer, tachometer and gauges. C
• Illumination of LCD color patterns for meter displays.
• Illumination of all lamps/LEDs that are controlled by the combination meter.
• Error code D
METHOD OF STARTING
How to Initiate Self-Diagnosis Mode
E
1. Turn ignition switch OFF.
2. While pressing the trip reset switch (1), turn ignition switch ON.
3. Press and hold the trip reset switch for 1 seconds or more.
4. Press the trip reset switch at least 3 times. (Within 7 seconds F
after the ignition switch is turned ON.)
5. “Work instruction code” is indicated in the top portion of informa-
tion display and self-diagnosis is started. G
NOTE:
When on-board diagnosis does not start, check the following
items and replace combination meter if the check results are
normal. H
• Combination meter power supply and ground circuits. Refer to
AWNIA4017ZZ
MWI-97, "COMBINATION METER (WITH INTELLIGENT KEY
SYSTEM) : Diagnosis Procedure" (with Intelligent Key system) or MWI-97, "COMBINATION METER I
(WITH INTELLIGENT KEY SYSTEM) : Diagnosis Procedure" (without Intelligent Key system).
• Trip reset switch signal circuits. Refer to MWI-122, "COMBINATION METER (WITH INTELLIGENT KEY
SYSTEM) : Diagnosis Procedure" (with Intelligent Key system) or MWI-123, "COMBINATION METER
(WITHOUT INTELLIGENT KEY SYSTEM) : Diagnosis Procedure" (without Intelligent Key system). J
6. The mode switches in the order shown below each time the trip reset switch is pressed.
NOTE:
• If the trip reset switch is not operated for 20 seconds or more, the self-diagnosis mode is automatically K
cancelled.
• The self-diagnosis mode is cancelled by turning the key switch OFF.
• The self-diagnosis mode is cancelled by engine speed 170 rpm or more.
L
Test order Test item Description

M
1 Work instruction code
2 Part number
3 Software code WCS
This item is displayed, but not used.
4 EEPROM code
5 Hardware code
6 P.C.B code O
The pointer of the following items moves from 0 to MAX twice:
• Speedometer
• Tachometer P
7 Circuit check • Engine coolant temperature gauge
• Fuel gauge
NOTE:
If any one of the pointers does not sweep, replace combination meter.
8 Color check*1 Performs the color check of the information display.

Displays the error code of the following items.
• Speedometer
• Tachometer
9 Error code*2 • Engine coolant temperature gauge
• Fuel gauge
• Meter control switch
All warning/indicator lamps illuminate.
NOTE:
10 Warning/indicator lamp check
• When either one of them does not turn ON, replace combination meter.
• SRS air bag warning lamp and security indicator lamp are not illuminated.
*1: Color Check
JSNIA5944ZZ
Blue Red Pink

Green Light blue Yellow
White White Black
Light blue Black Pink
Black Blue Black
Dark blue White Blue
*2: Error Code
JSNIA5945ZZ
Item Code Description Action to take/Reference

0 Normal —
A vehicle speed signal cannot be received Perform “Self Diagnostic Result” of
1 from ABS actuator and electric unit (control “ABS.”
Speedometer unit). • Refer to BRC-161, "DTC Index" (with
A vehicle speed signal received from the VDC).
2 ABS actuator and electric unit (control unit) • Refer to BRC-30, "DTC Index" (with-
is abnormal. out VDC).

A
0 Normal —
Perform “Self Diagnostic Result” of
“ECM.”
• Refer to EC-98, "DTC Index" (with B
QR25DE).
Tachometer An engine speed signal cannot be received • Refer to EC-494, "YS23DDT : DTC
1
from ECM. Index" (with YS23DDT (M9T)).
• Refer to EC-521, "YS23DDTT : DTC
C
Index" (with YS23DDTT (M9T)).
• Refer to EC-869, "DTC Index" (with
YD25DDTi). D
0 Normal —
1 Fuel gauge circuit is short. Refer to MWI-101, "COMBINATION
METER (WITH INTELLIGENT KEY E
SYSTEM) : Component Function
Fuel gauge Check" (with Intelligent Key system) or
2 Fuel gauge circuit is open. MWI-103, "COMBINATION METER
(WITHOUT INTELLIGENT KEY SYS- F
TEM) : Component Function Check"
(without Intelligent Key system).
0 Normal — G
“ECM.”
QR25DE).
H
Engine coolant temper-
ature gauge An engine coolant temperature signal can- • Refer to EC-494, "YS23DDT : DTC
1
not be received from ECM. Index" (with YS23DDT (M9T)).
I
YD25DDTi).
0 Normal — J
When judging that the display back switch • Refer to MWI-109, "COMBINATION
1 signal circuit is short-circuited for 5 minutes METER (WITH INTELLIGENT KEY
or more. SYSTEM) : Component Function K
Check" (with Intelligent Key system)
When judging that the display next switch
(Steering switch signal A circuit) or
2 signal circuit is short-circuited for 5 minutes
MWI-111, "COMBINATION METER
or more. L
(WITHOUT INTELLIGENT KEY
Check" (without Intelligent Key sys-
• Display next switch tem) (Steering switch signal A cir-
cuit).
M
• Display back switch
• Refer to MWI-114, "COMBINATION
METER (WITH INTELLIGENT KEY
When judging that the display next switch, SYSTEM) : Component Function WCS
3 and display back switch signal circuit are Check" (with Intelligent Key system)
short-circuited for 5 minutes or more. (Steering switch signal B circuit) or
MWI-116, "COMBINATION METER
(WITHOUT INTELLIGENT KEY O
Check" (without Intelligent Key sys-
tem) (Steering switch signal B cir-
cuit). P
— 0 Displays “0” constantly. —
How to Reset Error Code

Error codes stored in combination meter can be reset by following the instructions below:

2. While pressing the trip reset switch, turn ignition switch ON.
3. Keep the trip reset switch for 1 seconds or more.
4. Press the trip reset switch at least 3 times. (Within 7 seconds after the ignition switch is turned ON.)
6. Perform self-diagnosis and check that the error codes are reset.
WITH COLOR INFORMATION DISPLAY : CONSULT Function (METER/M&A)
INFOID:0000000014584484
APPLICATION ITEMS
CONSULT can display each diagnostic item using the diagnostic test modes shown.
METER/M&A Diagnosis mode Description

Self Diagnostic Result Displays combination meter self-diagnosis results.
Data Monitor Displays combination meter input/output data in real time.
Work support Displays diagnosis procedure of each work item.
ECU Identification Displays combination meter part number.
Warning History Lighting history of the warning lamp and indicator lamp can be checked.
• Read and save the vehicle specification.
Configuration
• Write the vehicle specification when replacing combination meter.
Self Diagnostic Result

Refer to MWI-39, "DTC Index" (with Intelligent Key system), or MWI-46, "EXCEPT BCM FUNCTION : DTC
Index" (without Intelligent Key system).
Data Monitor
Display Item List
X: Applicable
MAIN
Display item [Unit] Description
SIGNALS
SPEED METER
X Displays the value of vehicle speed signal.
[km/h or mph]
SPEED OUTPUT
X Vehicle speed signal value transmitted to other units via CAN communication.
[km/h or mph]
ODO OUTPUT
Odometer signal value transmitted to other units via CAN communication.
[km/h or mph]
TACHO METER
X Value of the engine speed signal received from ECM via CAN communication.
[rpm]
FUEL METER
X Fuel level indicated on combination meter.
[L]
W TEMP METER
X Displays the value of engine coolant temperature signal, which is input from ECM.
[°C or °F]
ABS W/L
Displays [ON/OFF] condition of ABS warning indicator.
[On/Off]
VDC/TCS IND
Displays [ON/OFF] condition of VDC OFF indicator lamp.
[On/Off]
SLIP IND
Displays [ON/OFF] condition of SLIP indicator lamp.
[On/Off]
Displays [ON/OFF] condition of brake warning indicator.
BRAKE W/L NOTE:
[On/Off] Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON.
DOOR W/L
Displays [ON/OFF] condition of door warning message in the information display.
[On/Off]

MAIN
SIGNALS A
HI-BEAM IND
Displays [ON/OFF] condition of high beam indicator.
[On/Off]
TURN IND B
Displays [ON/OFF] condition of turn indicator.
[On/Off]
FR FOG IND
Displays [ON/OFF] condition of front fog lamp indicator.
[On/Off] C
LIGHT IND
Displays [ON/OFF] condition of light indicator.
[On/Off]
OIL W/L D
Displays [ON/OFF] condition of low oil pressure warning indicator lamp.
[On/Off]
MIL
Displays [ON/OFF] condition of malfunction indicator.
[On/Off] E
GLOW IND
Displays [ON/OFF] condition of glow indicator lamp.
[On/Off]
C-ENG2 W/L
Displays [ON/OFF] condition of malfunction indicator lamp (red). F
[On/Off]
ATC/T-AMT W/L
Displays [ON/OFF] condition of A/T check warning indicator.
[Off]
G
4WD W/L
Displays [ON/OFF] condition of 4WD warning lamp.
[On/Off]
FUEL W/L H
Low fuel warning lamp status detected by the identified fuel level.
[On/Off]
WASHER W/L Displays [ON/OFF] condition of low washer fluid warning message in the informa-
[On/Off] tion display.
I
• Displays [ON/OFF] condition of Intelligent Key system malfunction (with Intelli-
KEY G/Y W/L gent Key system).
[On/Off] • Displays [ON/OFF] condition of key warning lamp (without Intelligent Key sys-
tem). J
DDS W/L
Displays [ON/OFF] condition of hill descent control indicator lamp.
[On/Off]
CHAGE W/L K
Displays [ON/OFF] condition of charge warning lamp.
[On/Off]
DPF W/L
This item is displayed, but can not be monitored.
[Off] L
ATP W/L
Displays [ON/OFF] condition of ATP warning lamp.
[On/Off]
FILTER W/L M
Displays [ON/OFF] condition of water in fuel warning lamp.
[On/Off]
LCD
[B&P I, B&P N, C&P I, C&P N, LK
Displays status of Intelligent Key system.
WCS
WN, BATT, KY>PSW, ID NG, SFT P,
ROTAT, NO KY, Off]
SHIFT IND
O
[P, R, N, D, M1, M2, M3, M4, M5, M6, Displays shift selector position.
M7]
4WD IND
Displays status of 4WD. P
[LOCK, 2W, 4Lo, HL1, HL2, MALF]
M RANGE SW
Displays [ON/OFF] condition of manual mode switch.
[On/Off]
NM RANGE SW
Displays [ON/OFF] condition of non-manual mode switch.
[On/Off]
AT SFT UP SW
Displays [ON/OFF] condition of manual mode shift up switch.
[On/Off]

MAIN
SIGNALS
AT SFT DWN SW
Displays [ON/OFF] condition of manual mode shift down switch.
[On/Off]
COMP F/B SIG A/C compressor activation condition that ECM judges according to the engine
[On/Off] coolant temperature and the acceleration degree.
PKB SW
Displays [ON/OFF] condition of parking brake switch.
[On/Off]
BUCKLE SW
Status of seat belt buckle switch LH.
[On/Off]
BRAKE OIL SW
Displays [ON/OFF] condition of brake fluid level switch.
[On/Off]
LED LMP R OPEN
Displays [ON/OFF] condition of LED headlamp (RH) warning message.
[On/Off]
LED LMP L OPEN
Displays [ON/OFF] condition of LED headlamp (LH) warning message.
[On/Off]
DIFF LOCK IND
Displays [ON/OFF] condition of electronic locking rear differential indicator.
[On/Off]
DISTANCE
Displays distance to empty.
[km or mile]
FUEL LOW SIG
Displays [ON/OFF] condition of low fuel signal.
[On/Off]
Buzzer status (in the combination meter) is detected from the buzzer output signal
BUZZER
X received from each unit via CAN communication and the warning output condition
[On/Off]
of the combination meter.
Displays [ON/OFF] condition of blinking status of ASCD or speed limiter set vehi-
ASCD SPD BLNK
cle speed that is judged by the ASCD status signal received from ECM via CAN
[On/Off]
communication.
ASCD STATUS Display status of ASCD and speed limiter status display judged by the ASCD sta-
[Off, ASCD, CRUISE] tus signal received from ECM via CAN communication.
ASCD REQ SPD ASCD set vehicle speed value judged by the ASCD status signal received from
[km/h or mph] ECM via CAN communication.
E/O CHG TMNG RST Displays [ON/OFF] condition of resetting remaining distance to the engine oil
[On/Off] change time.
WORK SUPPORT
Work support item Description

Fuel meter diagnosis(Analog pointer) A possible malfunction can be narrowed down by following dis-
Warning lamp diagnosis played instructions.
ECU IDENTIFICATION
Combination meter part number can be read.
WARNING HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “WARNING HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO WARNING HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• WARNING HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
CONFIGURATION
Configuration has three functions as follows.
A
Function Description
Allows the reading of vehicle specification written in combination
Before Replace ECU
meter to store the specification in CONSULT. B
Read/Write Configuration
Allows the writing of the vehicle information stored in CONSULT
After Replace ECU
into the combination meter.
Manual Configuration
Allows the writing of the vehicle specification into the combination C
meter by hand.
WITH MONOCHROME INFORMATION DISPLAY

D
WITH MONOCHROME INFORMATION DISPLAY : On Board Diagnosis Function
INFOID:0000000014584485
E
ON BOARD DIAGNOSIS ITEM
The following meter functions can be checked during Combination Meter Self-Diagnosis Mode:
• Pointer sweep of speedometer and tachometer.
• Illumination of all lamps/LEDs that are controlled by the combination meter. F
• Error code
METHOD OF STARTING G
How to Initiate Self-Diagnosis Mode
1. Turn ignition switch ON, press trip reset switch and set to "trip A" or "trip B".
2. Turn ignition switch OFF. H
3. While pressing the trip reset switch (1), turn ignition switch ON.
4. Press and hold the trip reset switch for 1 seconds or more.
5. Press the trip reset switch at least 3 times. (Within 7 seconds
after the ignition switch is turned ON.) I
6. “Work instruction code” is indicated in the top portion of informa-
tion display and self-diagnosis is started.
NOTE: J
When on-board diagnosis does not start, check the following
item and replace combination meter if the check results are nor-
mal.
K
Combination meter power supply and ground circuits. Refer to
JSNIA7591ZZ
MWI-200, "COMBINATION METER : Diagnosis Procedure".
7. The mode switches in the order shown below each time the trip reset switch is pressed.
NOTE: L
• If the trip reset switch is not operated for 20 seconds or more, the self-diagnosis mode is automatically
cancelled.
• The self-diagnosis mode is cancelled by turning the key switch OFF. M
• The self-diagnosis mode is cancelled by engine speed 170 rpm or more.
WCS
1 Work instruction code
2 Part number O
3 Software code
This item is displayed, but not used.
4 EEPROM code
5 Hardware code P
6 P.C.B code
The pointer of the following items moves from 0 to MAX twice.
• Speedometer
7 Circuit check • Tachometer
NOTE:
If any one of the pointers does not sweep, replace combination meter.

Displays the error code of the following items.
• Speedometer
8 Error code 1*1 • Tachometer
• Engine coolant temperature gauge
• Fuel gauge
9 Error code 2*2 Displays the error code of the trip reset switch.
All warning/indicator lamp illuminate.
10 Fuel NOTE:
When either one of them does not turn ON, replace combination meter.
*1: Error Code 1
JSNIA7666ZZ

0 Normal —
A vehicle speed signal cannot be received Perform “Self Diagnostic Result” of
1 from ABS actuator and electric unit (control “ABS.”
Speedometer unit). • Refer to BRC-161, "DTC Index" (With
A vehicle speed signal received from the VDC).
2 ABS actuator and electric unit (control unit) • Refer to BRC-30, "DTC Index" (With-
is abnormal. out VDC).
0 Normal —
“ECM.”
QR25DE).
Tachometer An engine speed signal cannot be received • Refer to EC-494, "YS23DDT : DTC
1
from ECM. Index" (with YS23DDT (M9T)).
YD25DDTi).
0 Normal —
Fuel gauge 1 Fuel gauge circuit is short. Refer to MWI-202, "Component Func-
2 Fuel gauge circuit is open. tion Check".

A
0 Normal —
“ECM.”
• Refer to EC-98, "DTC Index" (with B
Engine coolant temper- QR25DE).
ature gauge An engine coolant temperature signal can- • Refer to EC-494, "YS23DDT : DTC
1
not be received from ECM. Index" (with YS23DDT (M9T)).
C
YD25DDTi). D
*2: Error Code 2

E
JSNIA7666ZZ

— E Displays “E” constantly. — I
— 0 Displays “0” constantly. — J


K
How to Reset Error Code
Error codes stored in combination meter can be reset by following the instructions below:
1. Turn ignition switch OFF. L
2. While pressing the trip reset switch, turn ignition switch ON.
3. Keep the trip reset switch for 1 seconds or more.
4. Press the trip reset switch at least 3 times. (Within 7 seconds after the ignition switch is turned ON.)
5. Turn ignition switch OFF. M
6. Perform self-diagnosis and check that the error codes are reset.
WITH MONOCHROME INFORMATION DISPLAY : CONSULT Function (METER/ WCS
M&A) INFOID:0000000014584486
APPLICATION ITEMS O
CONSULT can display each diagnostic item using the diagnostic test modes shown.

P
Self Diagnostic Result Displays combination meter self-diagnosis results.
Data Monitor Displays combination meter input/output data in real time.
Work support Displays diagnosis procedure of each work item.
ECU Identification Displays combination meter part number.

Warning History Lighting history of the warning lamp and indicator lamp can be checked.
Configuration
• Write the vehicle specification when replacing combination meter.
Self Diagnostic Result

Refer to MWI-39, "DTC Index".
Data Monitor
Display Item List
X: Applicable
MAIN
SIGNALS
SPEED METER
X Displays the value of vehicle speed signal.
[km/h or mph]
SPEED OUTPUT
X Vehicle speed signal value transmitted to other units via CAN communication.
[km/h or mph]
ODO OUTPUT
Odometer signal value transmitted to other units via CAN communication.
[km/h or mph]
TACHO METER
X Value of the engine speed signal received from ECM via CAN communication.
[rpm]
FUEL METER
X Fuel level indicated on combination meter.
[L]
W TEMP METER
X Displays the value of engine coolant temperature signal, which is input from ECM.
[°C or °F]
ABS W/L
Displays [ON/OFF] condition of ABS warning indicator.
[On/Off]
VDC/TCS IND
Displays [ON/OFF] condition of VDC OFF indicator lamp.
[On/Off]
SLIP IND
Displays [ON/OFF] condition of SLIP indicator lamp.
[On/Off]
Displays [ON/OFF] condition of brake warning indicator.
BRAKE W/L NOTE:
[On/Off] Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON.
DOOR W/L
Displays [ON/OFF] condition of door warning message in the information display.
[On/Off]
HI-BEAM IND
Displays [ON/OFF] condition of high beam indicator.
[On/Off]
TURN IND
Displays [ON/OFF] condition of turn indicator.
[On/Off]
FR FOG IND
Displays [ON/OFF] condition of front fog lamp indicator.
[On/Off]
LIGHT IND
Displays [ON/OFF] condition of light indicator.
[On/Off]
OIL W/L
Displays [ON/OFF] condition of low oil pressure warning indicator lamp.
[On/Off]
MIL
Displays [ON/OFF] condition of malfunction indicator.
[On/Off]
GLOW IND
Displays [ON/OFF] condition of glow indicator lamp.
[On/Off]
C-ENG2 W/L
Displays [ON/OFF] condition of malfunction indicator lamp (red).
[On/Off]
4WD W/L
Displays [ON/OFF] condition of 4WD warning lamp.
[On/Off]

MAIN
SIGNALS A
FUEL W/L
Low fuel warning lamp status detected by the identified fuel level.
[On/Off]
WASHER W/L B
Displays [ON/OFF] condition of low washer fluid warning indicator lamp.
[On/Off]
KEY G/Y W/L
Displays [ON/OFF] condition of key warning lamp.
[On/Off] C
DDS W/L
Displays [ON/OFF] condition of hill descent control indicator lamp.
[On/Off]
CHAGE W/L D
Displays [ON/OFF] condition of charge warning lamp.
[On/Off]
DPF W/L
This item is displayed, but can not be monitored.
[Off] E
FILTER W/L
Displays [ON/OFF] condition of water in fuel warning lamp.
[On/Off]
4WD IND
Displays status of 4WD. F
[LOCK, 2W, 4Lo, HL1, HL2, MALF]
COMP F/B SIG A/C compressor activation condition that ECM judges according to the engine
[On/Off] coolant temperature and the acceleration degree.
G
PKB SW
Displays [ON/OFF] condition of parking brake switch.
[On/Off]
BUCKLE SW H
Status of seat belt buckle switch LH.
[On/Off]
BRAKE OIL SW
Displays [ON/OFF] condition of brake fluid level switch.
[On/Off]
I
DISTANCE
Displays distance to empty.
[km or mile]
FUEL LOW SIG J
Displays [ON/OFF] condition of low fuel signal.
[On/Off]
Buzzer status (in the combination meter) is detected from the buzzer output signal
BUZZER
X received from each unit via CAN communication and the warning output condition
[On/Off] K
of the combination meter.
Displays [ON/OFF] condition of blinking status of ASCD or speed limiter set vehi-
ASCD SPD BLNK
cle speed that is judged by the ASCD status signal received from ECM via CAN
[On/Off]
communication. L
ASCD STATUS Display status of ASCD and speed limiter status display judged by the ASCD sta-
[Off, ASCD, CRUISE] tus signal received from ECM via CAN communication.
ASCD REQ SPD ASCD set vehicle speed value judged by the ASCD status signal received from M
[km/h or mph] ECM via CAN communication.
E/O CHG TMNG RST Displays [ON/OFF] condition of resetting remaining distance to the engine oil
[On/Off] change time. WCS
WORK SUPPORT
Work support item Description O

Fuel meter diagnosis(Analog pointer) A possible malfunction can be narrowed down by following dis-
Warning lamp diagnosis played instructions.
P
ECU IDENTIFICATION
Combination meter part number can be read.
WARNING HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “WARNING HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is:

- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO WARNING HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• WARNING HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
CONFIGURATION
Configuration has three functions as follows.
Function Description
Allows the reading of vehicle specification written in combination
Before Replace ECU
meter to store the specification in CONSULT.
Read/Write Configuration
Allows the writing of the vehicle information stored in CONSULT
After Replace ECU
into the combination meter.
Allows the writing of the vehicle specification into the combination
Manual Configuration
meter by hand.

DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM (WITH INTELLIGENT KEY SYSTEM) : CONSULT Function (BCM -
B
COMMON ITEM) (With Intelligent Key) INFOID:0000000014589536
APPLICATION ITEM
C
CONSULT performs the following functions via CAN communication with BCM.
Diagnosis mode Function Description

D
Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM. E
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
ECU Identification The BCM part number is displayed. F
Configuration
• Write the vehicle specification when replacing BCM.
G
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE: H
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub System I
Work Support Data Monitor Active Test
Door lock DOOR LOCK × ×
Rear window defogger REAR DEFOGGER × × J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
K
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × × L
Automatic A/C AIR CONDITONER ×
• Intelligent Key system
INTELLIGENT KEY × × × M
• Engine start system
Combination switch COMB SW ×
Body control system BCM ×
WCS
NATS IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Trunk open TRUNK × O
Theft warning alarm THEFT ALM × × ×
RAP system RETAINED PWR ×
P
Signal buffer system SIGNAL BUFFER × ×
FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.

CONSULT screen item Indication/Unit Description

Vehicle Speed km/h Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular DTC is detected
While turning BCM status from low power consumption mode to
SLEEP>LOCK
normal mode (Power supply position is “LOCK”)
While turning BCM status from low power consumption mode to
SLEEP>OFF
normal mode (Power supply position is “OFF”.)
LOCK>ACC While turning power supply position from “LOCK” to “ACC”
ACC>ON While turning power supply position from “ACC” to “IGN”
While turning power supply position from “RUN” to “ACC” (Vehicle
RUN>ACC
is stopping and selector lever is except P position.)
While turning power supply position from “CRANKING” to “RUN”
CRANK>RUN
(From cranking up the engine to run it)
While turning power supply position from “RUN“ to “ACC” (Emer-
RUN>URGENT
gency stop operation)
ACC>OFF Power supply position While turning power supply position from “ACC” to “OFF”
status of the moment a
Vehicle Condition OFF>LOCK While turning power supply position from “OFF” to “LOCK”
particular DTC is de-
OFF>ACC tected* While turning power supply position from “OFF” to “ACC”
ON>CRANK While turning power supply position from “IGN” to “CRANKING”
While turning BCM status from normal mode (Power supply posi-
OFF>SLEEP
tion is “OFF”.) to low power consumption mode
While turning BCM status from normal mode (Power supply posi-
LOCK>SLEEP
tion is “LOCK”.) to low power consumption mode
LOCK Power supply position is “LOCK”.
OFF Power supply position is “OFF”.
ACC Power supply position is “ACC”.
ON Power supply position is “IGN”
ENGINE RUN Power supply position is “RUN”.
CRANKING Power supply position is “CRANKING”.
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
IGN Counter 0 - 39 • The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition
whenever ignition switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
NOTE:
*: Refer to the following for details at the power supply position.
• LOCK: Ignition switch OFF with steering locked
• OFF: Ignition switch OFF with steering unlocked
• ACC: Ignition switch ACC
• IGN: Ignition switch ON with engine stopped
• RUN: Ignition switch ON with engine running
• CRANKING: At engine cranking
COMMON ITEM (WITHOUT INTELLIGENT KEY SYSTEM)
COMMON ITEM (WITHOUT INTELLIGENT KEY SYSTEM) : CONSULT Function
(BCM - COMMON ITEM) (Without Intelligent Key) INFOID:0000000014589538
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.

Diagnosis mode Function Description A

Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.
B
Data Monitor The BCM input/output signals are displayed.

Active Test The signals used to activate each device are forcibly supplied from BCM. C
ECU Identification The BCM part number is displayed.
Configuration
• Write the vehicle specification when replacing BCM. D
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE: E
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode F
System Sub System
Work Support Data Monitor Active Test
Door lock DOOR LOCK × ×
G
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp control INT LAMP × × × H
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × × I
Turn signal and hazard warning lamps FLASHER × ×
Manual air conditioning AIR CONDITONER × ×
J
Combination switch COMB SW ×
Body control system BCM ×
Immobilizer IMMU × K
Interior room lamp battery saver BATTERY SAVER × ×
Vehicle security system THEFT ALM × ×
L
Signal buffer system SIGNAL BUFFER × ×
Panic alarm PANIC ALARM ×
BUZZER (WITH INTELLIGENT KEY) M
BUZZER (WITH INTELLIGENT KEY) : CONSULT Function (BCM - BUZZER)

INFOID:0000000014589537
WCS
DATA MONITOR
O
Monitor item [Unit] Description
PUSH SW [On/Off] Status of push-button ignition switch judged by BCM.
UNLK SEN-DR [On/Off] Status of unlock sensor judged by BCM. P
VEH SPEED 1 [km/h] Value of vehicle speed signal received from combination meter with CAN communication line.
TAIL LAMP SW [On/Off] Status of lighting switch judged by BCM using the combination switch readout function.
FR FOG SW [On/Off] Status of front fog lamp switch judged by BCM using the combination switch readout function.
DOOR SW-DR [On/Off] Status of front door switch LH judged by BCM.
CDL LOCK SW [On/Off] Status of door lock unlock switch judged by BCM.

ACTIVE TEST
Test Item Description

LIGHT WARN ALM This test is able to check light warning chime operation [On/Off].
REVERSE WARNING This test is able to check reverse warning chime operation [On/Off].
BUZZER (WITHOUT INTELLIGENT KEY)

BUZZER (WITHOUT INTELLIGENT KEY) : CONSULT Function (BCM - BUZZER)
INFOID:0000000014589539
DATA MONITOR
Monitor item [Unit] Description

IGN ON SW [On/Off] Indicates status of ignition switch judged by BCM.
KEY ON SW [On/Off] Indicates status of key switch judged by BCM.
DOOR SW-DR [km/h] Indicates status of front door LH switch judged by BCM.
TAIL LAMP SW [On/Off] Indicates status of lighting switch judged by BCM using the combination switch readout function.
FR FOG SW [On/Off] Indicates status of front fog lamp switch judged by BCM using the combination switch readout function.
BUCKLE SW [Off] Indicates status of buckle switch.
VEHICLE SPEED [km/h] Value of vehicle speed signal received from combination meter with CAN communication line.
ACTIVE TEST
Test item Description

IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).

COMBINATION METER (WITH INTELLIGENT KEY SYSTEM)
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION A
Reference Value INFOID:0000000014584651
B
VALUES ON THE DIAGNOSIS TOOL

C
Monitor Item Condition Value/Status
SPEED METER Input value of vehicle speed signal
Ignition switch ON While driving
[mph or km/h] (CAN communication signal)
D
SPEED OUTPUT Output value of vehicle speed sig-
[mph or km/h] nal (CAN communication signal)
ODO OUTPUT Output value of odometer signal E
Ignition switch ON —
TACHO METER Input value of engine speed signal
Ignition switch ON Engine running
[rpm] (CAN communication signal)
F
FUEL METER Input value of fuel level sensor sig-
[L] nal
Input value of engine coolant tem-
W TEMP METER G
Ignition switch ON — perature signal (CAN communica-
[°F or °C]
tion signal)
ABS warning lamp ON On
ABS W/L Ignition switch ON H
ABS warning lamp OFF Off
VDC OFF indicator lamp ON On
VDC/TCS IND Ignition switch ON
VDC OFF indicator lamp OFF Off I
VDC warning lamp ON On
SLIP IND Ignition switch ON
VDC warning lamp OFF Off
J
Brake warning lamp ON On
BRAKE W/L Ignition switch ON
Brake warning lamp OFF Off
Door warning lamp ON On K
DOOR W/L Ignition switch ON
Door warning lamp OFF Off
High beam indicator lamp ON On
HI-BEAM IND Ignition switch ON L
High beam indicator lamp OFF Off
Turn signal indicator lamp ON On
TURN IND Ignition switch ON
Turn signal indicator lamp OFF Off
M
Front fog lamp indicator lamp ON On
FR FOG IND Ignition switch ON
Front fog lamp indicator lamp OFF Off
Position lamp indicator lamp ON On WCS
LIGHT IND Ignition switch ON
Position lamp indicator lamp OFF Off
Oil pressure warning lamp ON On
OIL W/L Ignition switch ON O
Oil pressure warning lamp OFF Off
Malfunction indicator lamp ON On
MIL Ignition switch ON
Malfunction indicator lamp OFF Off P
Glow indicator lamp ON On
GLOW IND Ignition switch ON
Glow indicator lamp OFF Off
Malfunction indicator lamp (red) ON On
C-ENG2 W/L Ignition switch ON
Malfunction indicator lamp (red) OFF Off

A/T check warning indicator lamp ON. On
ATC/T-AMT W/L Ignition switch
A/T check warning indicator lamp OFF. Off
During 4WD warning indication On
4WD W/L Ignition switch ON
Except during 4WD warning indication Off
Low fuel warning lamp OFF On
FUEL W/L Ignition switch ON
Low fuel warning lamp OFF Off
Low washer fluid warning ON On
WASHER W/L Ignition switch ON
Low washer fluid warning OFF Off
During Intelligent Key system malfunction
On
indication
KEY G/Y W/L Ignition switch ON
Except during Intelligent Key system mal-
Off
function indication
Hill descent control indicator lamp ON On
DDS W/L Ignition switch ON
Hill descent control indicator lamp OFF Off
Charge warning lamp ON On
CHAGE W/L Ignition switch ON
Charge warning lamp OFF Off
NOTE:
DPF W/L Engine running This item is displayed, but can not be mon- Off
itored.
ATP warning lamp ON On
ATP W/L Ignition switch ON
ATP warning lamp OFF Off
Water-in-fuel-filter warning lamp ON On
FILTER W/L Ignition switch ON
Water-in-fuel-filter warning lamp OFF Off
During engine start information indication
B&P I
(Except M/T models)
Ignition switch ON
C&P I
(M/T models)
B&P N
(Except M/T models)
Ignition switch ACC
C&P N
(M/T models)
Ignition switch ON During ACC warning indication LK WN
Ignition switch During Intelligent Key low battery warning
BATT
LCD LOCK indication
Ignition switch During key ID verification information indi-
KY>PSW
LOCK cation
Ignition switch
During key ID warning indication ID NG
LOCK
Ignition switch
During P position warning indication SFT P
LOCK
Ignition switch
During steering lock information indication ROTAT
LOCK
Ignition switch ON During take away warning indication NO KY
Ignition switch ON Other than the above Off
[P, R, N, D, M1, M2, M3, M4, M5,
SHIFT IND Ignition switch ON Position of shift selector
M6, M7]

A
During LOCK indication LOCK
During 2W indication 2W
4WD IND Ignition switch ON During 4LO indication 4Lo B
During H-L SHIFT1 indication HL1
Shift selector in manual mode position On C
M RANGE SW Ignition switch ON
Other than the above Off
Shift selector in manual mode position Off
NM RANGE SW Ignition switch ON D
Other than the above On
Shift selector operated in the up position On
AT SFT UP SW Ignition switch ON
Other than the above Off E
Shift selector operated in the down posi-
On
AT SFT DWN SW Ignition switch ON tion
Other than the above Off F
A/C compressor activation condition On
COMP F/B SIG Ignition switch ON
G
Parking brake switch ON On
PKB SW Ignition switch ON
Parking brake switch OFF Off
When seat belt buckle LH is unfastened. On H
BUCKLE SW Ignition switch ON
When seat belt buckle LH is fastened. Off
Brake fluid level switch ON On
BRAKE OIL SW Ignition switch ON I
Brake fluid level switch OFF Off
Front combination lamp RH malfunction On
LED LMP R OPEN Ignition switch ON
Front combination lamp RH normal Off J
Front combination lamp LH malfunction On
LED LMP L OPEN Ignition switch ON
Front combination lamp LH normal Off
K
Diff lock switch ON On
DIFF LOCK IND Ignition switch ON
Diff lock switch OFF Off
DISTANCE L
Ignition switch ON — Distance to empty
[mile] or [km]
Low fuel On
FUEL LOW SIG Ignition switch ON
Other than above Off M
Buzzer ON On
BUZZER Ignition switch ON
Buzzer OFF Off
WCS
Set vehicle speed indicator blinking On
ASCD SPD BLNK Ignition switch ON
Set vehicle speed indicator not blinking Off
ASCD system OFF Off O
ASCD STATUS Ignition switch ON ASCD system ON ASCD
ASCD set vehicle speed CRUISE
Same value as ASCD set vehicle P
ASCD REQ SPD Ignition switch ON While driving
speed
Resetting of a remaining distance to the
On
E/O CHG TMNG RST Ignition switch ON engine oil change time.
Other than above Off

TERMINAL LAYOUT
JSNIA6097ZZ
PHYSICAL VALUES
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
1
Ground Ground — — — 0V
(B)
Ignition Security indicator ON 0V
7
Ground Security signal Input switch
(R) Security indicator OFF Battery voltage
ON
Ignition Charge warning lamp ON 0V
11
Ground Alternator signal Input switch
(BR) Charge warning lamp OFF Battery voltage
ON
Ignition Headlamp ON 1.0 V
12 LED headlamp RH warning
Ground Input switch
(LG) signal Headlamp OFF Battery voltage
ON
Ignition Headlamp ON 1.0 V
13 LED headlamp LH warning
Ground Input switch
(BG) signal Headlamp OFF Battery voltage
ON
Ignition
14
Ground ACC power supply Input switch — Battery voltage
(R)
ACC
SRS air bag warning lamp
Ignition —
16 ON
Ground Airbag signal Input switch
(BR) SRS air bag warning lamp
ON —
OFF
Ignition Trip reset switch is pressed 0V
18
Ground Trip reset switch signal Input switch
(P) Other than the above 5V
ON
Water-in fuel warning lamp
Ignition 0V
21 ON
Ground Water in fuel sensor signal Input switch
(R) Water-in fuel warning lamp
ON Battery voltage
OFF
Keep pressing SOURCE
0V
switch
Keep pressing MENU UP
0.5 V
switch
Ignition
22
Ground Steering switch signal A Input switch Keep pressing MENU
(V) 1.2 V
ON DOWN switch
Keep pressing TEL switch 2.1 V
Keep pressing ENTER
3.3 V
switch

Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
Keep pressing VOLUME B
0V
DOWN switch
Keep pressing VOLUME UP
0.5 V
switch C
Ignition
23 Keep pressing TEL END
Ground Steering switch signal B Input switch 1.2 V
(BG) switch
ON
Keep pressing DISPLAY D
2.1 V
BACK switch
Keep pressing DISPLAY
3.3 V
NEXT switch E
Ignition Washer fluid level switch ON 0V
24 Washer fluid level switch
Ground Input switch Washer fluid level switch
(V) signal 5V
ON OFF F
Ignition Brake fluid level low 0V
25 Brake fluid level switch sig-
Ground Input switch
(W) nal Brake fluid level normal Battery voltage
ON
G
Ignition Parking brake applied 0V
26
Ground Parking brake switch signal Input switch
(G) Parking brake released Battery voltage
ON
H
Ignition Unfastened 0V
28 Seat belt buckle switch LH
Ground Input switch
(W) signal Fastened Battery voltage
ON
Selector lever manual mode
I
Ignition 0V
30 position
Ground Manual mode signal Input switch
(LG)
ON Other than the above Battery voltage
J
Ignition Selector lever manual mode
31 Battery voltage
Ground Non-manual mode signal Input switch position
(Y)
ON Other than the above 0V
K
Ignition Selector lever UP operation 0V
32 Manual mode shift up sig-
Ground Input switch
(V) nal Other than the above Battery voltage
ON
L
Ignition Selector lever DOWN opera-
33 Manual mode shift down 0V
Ground Input switch tion
(BG) signal
ON Other than the above Battery voltage
M
Ignition Illumination control switch
36 Illumination control switch 0V
Ground Input switch (+) is pressed
(R) signal (+)
WCS
Ignition Illumination control switch (−
Ground Input switch ) is pressed
(G) signal (−)
O
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit). P
Ignition Speedometer operated
38 Vehicle speed signal
Ground Output switch [When vehicle speed is ap-
(SB) (8-pulse)
ON prox. 25 MPH (40 km/h)]
JSNIA0012GB

Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
41
Ground CAN high — — — —
(L)
42
Ground CAN low — — — —
(P)
Ignition
44
Ground Fuel level sensor ground — switch — 0V
(B)
ON
Ignition
45
Ground Battery power supply Input switch — Battery voltage
(R)
OFF
Ignition
46
Ground Ignition signal Input switch — Battery voltage
(BG)
ON
47
Ground M CAN high — — — —
(SB)
48
Ground M CAN low — — — —
(LG)
Ignition
49 MWI-108, "Component Inspec-
Ground Oil level sensor signal Input switch —
(L) tion"
ON
Ignition
50
Ground Oil level sensor ground — switch — 0V
(SB)
ON
Ignition
51
Ground Fuel level sensor signal Input switch — Battery voltage
(Y)
ON
52
(B)
Fail-Safe INFOID:0000000014584652
Function Specifications
Speedometer
Reset to zero by suspending communication.
Tachometer
• When reception time of an abnormal signal is 60 seconds or
less, the last value received.
Engine coolant temperature gauge
• When reception time of an abnormal signal is more than 60
seconds, reset to zero.
Illumination control When suspending communication, changes to nighttime mode.
Odo/trip meter An indicated value is maintained at communications blackout.
Shift position indicator The display turns OFF by suspending communication.
Current fuel consump-
tion
Trip com- Average fuel consump-

Information display tion The last result calculated during normal condition is indicated.
puter
Average vehicle speed
Distance to empty
Warning/ 4WD warning The display turns ON by suspending communication.

Indicator Other than the above The display turns OFF by suspending communication.

A
ABS warning lamp
VDC warning lamp B
Brake warning lamp
4WD warning lamp The lamp turns ON by suspending communication.
ATP warning lamp C

Malfunction indicator lamp (MIL) (yel-
low)
D
High beam indicator lamp
Malfunction indicator lamp (MIL) (red)
Warning lamp/indicator lamp
VDC OFF indicator lamp E
Turn signal indicator lamp
Front fog lamp indicator lamp
Position lamp indicator lamp The lamp turns OFF by suspending communication. F
Hill descent control indicator lamp
Glow indicator lamp
G
Door warning lamp
Engine oil pressure warning lamp
Differential lock indicator lamp H
DTC Inspection Priority Chart INFOID:0000000014584653
I
If multiple DTCs are detected simultaneously, check them one by one depending on the following DTC inspec-
tion priority chart.
Priority Detected items (DTC) J

• U1000: CAN COMM CIRCUIT
1
• U1010: CONTROL UNIT (CAN)
K
• B2205: VEHICLE SPEED
• B2267: ENGINE SPEED
2 • B2268: WATER TEMP
• B2321: OIL LEVEL SENSOR INPUT OPEN L
• B2322: OIL LEVEL SENSOR INPUT SHORT
DTC Index INFOID:0000000014584654

M
Display contents of CONSULT Diagnostic item is detected when... Refer to

CAN COMM CIRCUIT Combination meter is not transmitting or receiving CAN communication signal for 2 WCS
MWI-88
[U1000] seconds or more.
CONTROL UNIT (CAN)
Detecting error during the initial diagnosis of CAN controller of combination meter. MWI-89
[U1010] O
VEHICLE SPEED The abnormal vehicle speed signal is input from ABS actuator and electric unit (con-
MWI-90
[B2205] trol unit) for 2 seconds or more.
ENGINE SPEED P
ECM continuously transmits abnormal engine speed signals for 2 seconds or more. MWI-91
[B2267]
WATER TEMP ECM continuously transmits abnormal engine coolant temperature signals for 60
MWI-92
[B2268] seconds or more.

OIL LEVEL SENSOR INPUT
OPEN Oil level sensor signal circuit is open. MWI-93
[B2321]
SHORT Oil level sensor signal circuit is shorted. MWI-93
[B2322]

COMBINATION METER (COLOR DISPLAY MODELS WITHOUT INTELLIGENT
KEY)
COMBINATION METER (COLOR DISPLAY MODELS WITHOUT INTELLI-
A
GENT KEY)
EXCEPT BCM FUNCTION
B
EXCEPT BCM FUNCTION : Reference Value INFOID:0000000014584665
VALUES ON THE DIAGNOSIS TOOL C

SPEED METER Input value of vehicle speed signal D
[mph or km/h] nal (CAN communication signal)
E
ODO OUTPUT Output value of odometer signal
Ignition switch ON Engine running F
[L] nal
G
W TEMP METER
[°F or °C]
tion signal)
H
ABS W/L Ignition switch ON
VDC/TCS IND Ignition switch ON I
VDC OFF indicator lamp OFF Off
VDC warning lamp OFF Off J
K
Door warning lamp ON On
High beam indicator lamp ON On L
HI-BEAM IND Ignition switch ON
TURN IND Ignition switch ON M
Front fog lamp indicator lamp OFF Off WCS
Position lamp indicator lamp ON On
O
OIL W/L Ignition switch ON
Malfunction indicator lamp ON On P
Malfunction indicator lamp OFF Off

KEY)
During 4WD warning indication On
Low fuel warning lamp OFF Off
Key warning lamp ON On
KEY G/Y W/L Ignition switch ON
Key warning lamp OFF Off
Charge warning lamp ON On
NOTE:
itored.
FILTER W/L Ignition switch ON
During 2W indication 2W
4WD IND Ignition switch ON During 4LO indication 4Lo
When seat belt buckle LH is unfastened. On
BRAKE OIL SW Ignition switch ON
DISTANCE
[mile] or [km]
Low fuel On
Buzzer ON On
Buzzer OFF Off
ASCD SPD BLNK Ignition switch ON
ASCD system OFF Off
Same value as ASCD set vehicle
speed
On

KEY)
TERMINAL LAYOUT
A
I
AWNIA4042ZZ
PHYSICAL VALUES
J
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.) K
+ – Signal name
Output
1
(B) L
Ignition Security indicator ON 0V
7
Ground Security signal Input switch
(R) Security indicator OFF Battery voltage
ON
M
Ignition Charge warning lamp ON 0V
11
Ground Alternator signal Input switch
(BR) Charge warning lamp OFF Battery voltage
ON
WCS
Ignition
14
Ground ACC power supply Input switch — Battery voltage
(R)
ACC
SRS air bag warning lamp O
Ignition —
16 ON
Ground Airbag signal Input switch
(BR) SRS air bag warning lamp
ON —
OFF P
Ignition Trip reset switch is pressed 0V
18
Ground Trip reset switch signal Input switch
(P) Other than the above 5V
ON

KEY)
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Water-in fuel warning lamp
Ignition 0V
21 ON
Ground Water in fuel sensor signal Input switch
(R) Water-in fuel warning lamp
ON Battery voltage
OFF
Keep pressing SOURCE
0V
switch
Keep pressing MENU UP
0.5 V
switch
Ignition
22
Ground Steering switch signal A Input switch Keep pressing MENU
(V) 1.2 V
ON DOWN switch
Keep pressing TEL switch 2.1 V
Keep pressing ENTER
3.3 V
switch
Keep pressing VOLUME
0V
DOWN switch
Keep pressing VOLUME UP
0.5 V
switch
Ignition
23 Keep pressing TEL END
Ground Steering switch signal B Input switch 1.2 V
(BG) switch
ON
2.1 V
BACK switch
3.3 V
NEXT switch
Ignition Washer level switch ON 0V
24 Washer fluid level switch
Ground Input switch
(V) signal Washer level switch OFF 5V
ON
Ignition Brake fluid level low 0V
25 Brake fluid level switch sig-
Ground Input switch
(W) nal Brake fluid level normal Battery voltage
ON
Ignition Parking brake applied 0V
26
Ground Parking brake switch signal Input switch
(G) Parking brake released Battery voltage
ON
Ignition Unfastened 0V
28 Seat belt buckle switch LH
Ground Input switch
(W) signal Fastened Battery voltage
ON
Ignition Illumination control switch

Ground Input switch (+) is pressed
(R) signal (+)
Ignition Illumination control switch (−

Ground Input switch ) is pressed
(G) signal (−)
NOTE:
(destination unit).
Ignition Speedometer operated
38 Vehicle speed signal
Ground Output switch [When vehicle speed is ap-
(SB) (8-pulse)
ON prox. 25 MPH (40 km/h)]
JSNIA0012GB

KEY)
Terminal No.
Description
Condition
Input/ (Approx.)
+ – Signal name
Output
41 B
(L)
42
(P) C
Ignition
44
Ground Fuel level sensor ground — switch — 0V
(B)
ON D
Ignition
45
Ground Battery power supply Input switch — Battery voltage
(R)
OFF
E
Ignition
46
Ground Ignition signal Input switch — Battery voltage
(BG)
ON
47
F
Ground M-CAN high — — — —
(SB)
48
Ground M-CAN low — — — — G
(LG)
Ignition
49 MWI-108, "Component Inspec-
Ground Oil level sensor signal Input switch —
(L) tion"
ON H
Ignition
50
Ground Oil level sensor ground — switch — 0V
(SB)
ON
I
Ignition
51
Ground Fuel level sensor signal Input switch — —
(Y)
ON
J
52
(B)
79
(B)
Ground Ground — — — 0V K
EXCEPT BCM FUNCTION : Fail-Safe INFOID:0000000014584666
L
M
Speedometer
Tachometer
• When reception time of an abnormal signal is 60 seconds or WCS
O

KEY)
tion

tion The last result calculated during normal condition is indicated.
Information display puter
Distance to empty
Warning/ 4WD warning The display turns ON by suspending communication.

Indicator Other than the above The display turns OFF by suspending communication.
ABS warning lamp
VDC warning lamp
Brake warning lamp
The lamp turns ON by suspending communication.
4WD warning lamp
Malfunction indicator lamp (MIL) (yel-
low)
Malfunction indicator lamp (MIL) (red)
Warning lamp/indicator lamp VDC OFF indicator lamp

Front fog lamp indicator lamp
Position lamp indicator lamp The lamp turns OFF by suspending communication.
Hill descent control indicator lamp
Glow indicator lamp
Door warning lamp
Differential lock indicator lamp
EXCEPT BCM FUNCTION : DTC Inspection Priority Chart INFOID:0000000014584667
Priority Detected items (DTC)

1
• B2321: OIL LEVEL SENSOR INPUT OPEN
EXCEPT BCM FUNCTION : DTC Index INFOID:0000000014584668

CAN COMM CIRCUIT Combination meter is not transmitting or receiving CAN communication signal for 2
MWI-88
CONTROL UNIT (CAN)
[U1010]

KEY)
A
MWI-90
ENGINE SPEED
ECM continuously transmits abnormal engine speed signals for 2 seconds or more. MWI-91 B
[B2267]
MWI-92
OIL LEVEL SENSOR INPUT C
[B2321]
OIL LEVEL SENSOR INPUT D
[B2322]
WCS

COMBINATION METER (MONOCHROME DISPLAY MODELS WITHOUT INTEL-
LIGENT KEY)
COMBINATION METER (MONOCHROME DISPLAY MODELS WITHOUT
INTELLIGENT KEY)
EXCEPT BCM FUNCTION
EXCEPT BCM FUNCTION : Reference Value INFOID:0000000014584695
VALUES ON THE DIAGNOSIS TOOL

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

SPEED METER
Ignition switch ON While driving Input value of vehicle speed signal
[mph or km/h]
[mph or km/h] nal
ODO OUTPUT Output value of odometer signal
Ignition switch ON Engine running
[L] nal
W TEMP METER
[°F or °C]
tion signal)
ABS W/L Ignition switch ON
VDC/TCS IND Ignition switch ON
VDC OFF indicator lamp OFF Off
VDC warning lamp OFF Off
Door warning lamp ON On
High beam indicator lamp ON On
HI-BEAM IND Ignition switch ON
TURN IND Ignition switch ON
Front fog lamp indicator lamp OFF Off
Position lamp indicator lamp ON On
OIL W/L Ignition switch ON
Malfunction indicator lamp ON On
Malfunction indicator lamp OFF Off

LIGENT KEY)
A
During 4WD warning indication On B
Low fuel warning lamp OFF Off C
D
During ignition Key malfunction On
KEY G/Y W/L Ignition switch ON Except during During ignition Key mal-
Off
function E
Charge warning lamp ON On F
NOTE:
G
itored.
FILTER W/L Ignition switch ON H
During 2W indication 2W I
4WD IND Ignition switch ON During 4LO indication 4Lo
J
Other than the above Off K
When seat belt buckle LH is unfastened. On L
BRAKE OIL SW Ignition switch ON M
DISTANCE
[mile] or [km] WCS
Low fuel On
Buzzer ON On O
Buzzer OFF Off
ASCD SPD BLNK Ignition switch ON P
ASCD system OFF Off
Same value as ASCD set vehicle
speed

LIGENT KEY)
On
TERMINAL LAYOUT
AWNIA4051ZZ
PHYSICAL VALUES
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Igni- Washer fluid level switch ON 0V
4 Washer fluid level tion
Ground Input
(V) switch signal switch Washer fluid level switch OFF 5.0 V
OFF
Igni- Water in fuel warning lamp:

0V
5 Water in fuel warning tion ON
Ground Input
(R) signal switch Water in fuel warning lamp:
ON Battery voltage
OFF

LIGENT KEY)
Terminal No.
Description
Condition
Input/ (Approx.)
+ – Signal name
Output
Igni- B
6 tion
Ground ACC power supply Input — Battery voltage
(R) switch
ACC
C
Igni- Unfastened 0V
12 Seat belt buckle switch tion
Ground Input
(W) LH signal switch Fastened Battery voltage
ON D
Igni-
14 Ground tion
Ground — — 0V
(B) (without Airbags) switch E
ON
Igni-
14 Airbag signal tion
(BR)
Ground
(with Airbags)
Input
switch
— — F
ON
Igni-
15 tion G
Ground Fuel level sensor signal Input — Battery voltage
(Y) switch
ON
H
Speedometer operated [When

vehicle speed is approx. 20 I
km/h (12.5 MPH)]
JSNIA3084ZZ J
Igni- K
16 Vehicle speed sensor tion
Ground Input vehicle speed is approx. 40
(G) signal switch
km/h (25 MPH)]
ON
L
JSNIA3085ZZ
M
vehicle speed is approx. 60
km/h (37.5 MPH)] WCS
JSNIA3086ZZ
O
NOTE:
(destination unit). P
Igni-
17 Vehicle speed signal tion
Ground Output vehicle speed is approx. 40
(SB) (8-pulse) switch
km/h (25 MPH)]
ON
JSNIA0012GB

LIGENT KEY)
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
19
(P)
20
(L)
Igni-
23 tion
Ground Oil level sensor ground — — 0V
(SB) switch
ON
Igni-
24 tion MWI-199, "Component Inspec-
Ground Oil level sensor signal Input —
(L) switch tion"
ON
Igni- Brake fluid level low 0V
31 Brake fluid level switch tion
Ground Input
(W) signal switch Brake fluid level normal Battery voltage
ON
Igni- Parking brake applied 0V
32 Parking brake switch tion
Ground Input
(G) signal switch Parking brake released Battery voltage
ON
Igni-
33 tion
Ground Ignition signal Input — Battery voltage
(BG) switch
ON
Igni- Brake pedal applied 0V
34 tion
Ground Stop lamp switch signal Input
(Y) switch Brake pedal released Battery voltage
ON
Igni-
35 Vehicle speed sensor tion
Ground — — 0V
(R) signal ground switch
ON
Igni- Charge warning lamp ON 0V
36 tion
Ground Alternator signal Input
(BR) switch Charge warning lamp OFF Battery voltage
ON
Igni-
37 Fuel level sensor tion
Ground — — 0V
(B) ground switch
ON
Igni-
39 tion
Ground Ground — — 0V
(B) switch
ON
Igni-
40 tion
(B) switch
ON

LIGENT KEY)
Terminal No.
Description
Condition
Input/ (Approx.)
+ – Signal name
Output
Igni- B
65 tion
Ground Battery power supply Input — Battery voltage
(R) switch
OFF
C
Igni-
79 tion
(B) switch
ON D
EXCEPT BCM FUNCTION : Fail-Safe INFOID:0000000014584696
E
F
Speedometer
Tachometer
• When reception time of an abnormal signal is 60 seconds or G
H
• When reception time of an abnormal signal is 60 seconds or I
J
Information display tion

tion The last result calculated during normal condition is indicated. K
puter
Distance to empty
L
4WD indicator The display turns OFF by suspending communication.
ABS warning lamp M
VDC warning lamp
The lamp turns ON by suspending communication.
Brake warning lamp
WCS
4WD warning lamp
Malfunction indicator lamp (MIL) O
Warning lamp/indicator lamp
VDC OFF indicator lamp
The lamp turns OFF by suspending communication.
Hill descent control indicator lamp P
Glow indicator lamp
Door warning lamp

LIGENT KEY)
EXCEPT BCM FUNCTION : DTC Inspection Priority Chart INFOID:0000000014584697
Priority Detected items (DTC)

1
• B2321: OIL LEVEL SENSOR INPUT OPEN
EXCEPT BCM FUNCTION : DTC Index INFOID:0000000014584698

CAN COMM CIRCUIT Combination meter is not transmitting or receiving CAN communication signal for 2
MWI-193
CONTROL UNIT (CAN)
[U1010]
MWI-195
ENGINE SPEED
ECM continuously transmits abnormal engine speed signals for 2 seconds or more. MWI-196
[B2267]
MWI-197
[B2321]
[B2322]

BCM
BCM
A
List of ECU Reference INFOID:0000000014250288
B
ECU Reference
BCS-31, "Reference Value"
With Intelligent Key sys- BCS-48, "Fail-safe" C

tem BCS-49, "DTC Inspection Priority Chart"
BCS-50, "DTC Index"
BCM D
BCS-97, "Reference Value With Monochrome Display"
Without Intelligent Key BCS-115, "Fail-safe"

system BCS-115, "DTC Inspection Priority Chart" E
BCS-116, "DTC Index"
WCS

< WIRING DIAGRAM >
WIRING DIAGRAM
Wiring Diagram - (with Color Display and Intelligent Key System) INFOID:0000000014250289
ABNWA3295GB

< WIRING DIAGRAM >
WCS
ABNIA9962GB

< WIRING DIAGRAM >
ABNIA9963GB

< WIRING DIAGRAM >
WCS
ABNIA9964GB

< WIRING DIAGRAM >
ABNIA9965GB

< WIRING DIAGRAM >
WCS
ABNIA9966GB

< WIRING DIAGRAM >
Wiring Diagram - (with Color Display and without Intelligent Key System) INFOID:0000000014250290
ABNWA3305GB

< WIRING DIAGRAM >
WCS
ABNIA9974GB

< WIRING DIAGRAM >
ABNIA9975GB

< WIRING DIAGRAM >
WCS
ABNIA9976GB

< WIRING DIAGRAM >
ABNIA9977GB

< WIRING DIAGRAM >
WCS
ABNIA9978GB

< WIRING DIAGRAM >
Wiring Diagram - (with Monochrome Display) INFOID:0000000014250291
ABNWA3306GB

< WIRING DIAGRAM >
WCS
ABNIA9967GB

< WIRING DIAGRAM >
ABNIA9968GB

< WIRING DIAGRAM >
WCS
ABNIA9969GB

< WIRING DIAGRAM >
ABNIA9970GB

< WIRING DIAGRAM >
WCS
ABNIA9971GB

< WIRING DIAGRAM >
ABNIA9972GB

< WIRING DIAGRAM >
WCS
ABNIA9973GB

DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION
Work Flow INFOID:0000000014250292
OVERALL SEQUENCE
AWNIA3769GB
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
>> GO TO 2.
2.CHECK SYMPTOM
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT SELF-DIAGNOSIS RESULTS

< BASIC INSPECTION >
Perform self-diagnosis. Refer to MWI-39, "DTC Index" combination meter (with Intelligent Key system) or
MWI-46, "EXCEPT BCM FUNCTION : DTC Index" combination meter (color display models without Intelligent A
Key system) or MWI-171, "EXCEPT BCM FUNCTION : DTC Index" combination meter (monochrome display
models without Intelligent Key system).
Is the inspection result normal? B
YES >> GO TO 4.
NO >> GO TO 5.
4.NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS C
Perform symptom diagnosis.
D
>> GO TO 5.
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts. E
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
F
>> GO TO 6.
6.FINAL CHECK
G
Check that the warning buzzer in the combination meter operates normally.
Is the inspection result normal?
YES >> Inspection End. H
NO >> GO TO 2.
WCS

POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS
COMBINATION METER (WITH INTELLIGENT KEY SYSTEM) : Diagnosis Procedure
INFOID:0000000014585025
Regarding Wiring Diagram information, refer to MWI-66, "Wiring Diagram - (with Intelligent Key system)".
1.CHECK FUSES
Check that the following fuses are not blown:
Unit Power source Fuse No.

Battery 13
Combination meter Ignition switch ON or ACC 20
Ignition switch ON or START 31
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Disconnect combination meter harness connectors.
2. Check voltage between combination meter harness connectors and ground.
Combination meter Ignition switch position

Ground
Connector Terminal OFF ON or ACC START
M106 14 0V Battery voltage Battery voltage
45 (–) Battery voltage Battery voltage Battery voltage
M107
46 0V Battery voltage Battery voltage
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3.CHECK GROUND CIRCUIT
2. Check continuity between combination meter harness connectors and ground.
Combination meter
Ground Continuity
Connector Terminal
M106 1
(–) Yes
M107 52
YES >> Inspection End.
KEY)
COMBINATION METER (COLOR DISPLAY MODELS WITHOUT INTELLIGENT KEY)

: Diagnosis Procedure INFOID:0000000014589726
Regarding Wiring Diagram information, refer to MWI-49, "Wiring Diagram - (with Color Display)".
B
1.CHECK FUSES
Check that the following fuses are not blown: C

Battery 13 D
E
Is the fuse blown?
NO >> GO TO 2. F
1. Disconnect combination meter harness connectors M71 and M85.
2. Check voltage between combination meter harness connector M71, M85 and ground. G

Ground H
M71 14 0V Battery voltage Battery voltage
45 (–) Battery voltage Battery voltage Battery voltage I
M85
J
YES >> GO TO 3.
3.CHECK GROUND CIRCUIT K
2. Disconnect combination meter harness connector M56.
3. Check continuity between combination meter harness connector M56, M71, M85 and ground. L
Combination meter
Ground Continuity
Connector Terminal M
M71 1
M85 52 (–) Yes
WCS
M56 79
YES >> Inspection End. O
LIGENT KEY) P
COMBINATION METER (MONOCHROME DISPLAY MODELS WITHOUT INTELLI-

GENT KEY) : Diagnosis Procedure INFOID:0000000014585032
Regarding Wiring Diagram information, refer to MWI-173, "Wiring Diagram".

1.CHECK FUSES
Check that the following fuses are not blown:

Battery 13
Is the fuse blown?
NO >> GO TO 2.
1. Disconnect combination meter harness connector.
2. Check voltage between combination meter harness connector and ground.

Ground
M24
33 (–) 0V Battery voltage Battery voltage
M87 65 Battery voltage Battery voltage Battery voltage
YES >> GO TO 3.
2. Check continuity between combination meter harness connector and ground.
Combination meter
Ground Continuity
Connector Terminal
39
M24
40 (–) Yes
M87 79
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis
Procedure INFOID:0000000014585037
Regarding Wiring Diagram information, refer to BCS-53, "Wiring Diagram".
1.CHECK FUSE AND FUSIBLE LINK

Check if the following BCM fuse or fusible links are blown.

Signal name Fuse and fusible link No. A

F (50A)
Battery power supply
16 (5A)
B
Is the fuse or fusible link blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO >> GO TO 2. C

1. Turn ignition switch OFF. D
2. Disconnect BCM connectors.
3. Check voltage between BCM harness connector and ground.
E
(+)
Voltage
BCM (−)
(Approx.)
Connector Terminal F
42
M19 Ground Battery voltage
55
G
YES >> GO TO 3.
NO >> Repair harness or connector.
H
Check continuity between BCM harness connector and ground.
I
BCM
Continuity
Connector Terminal Ground
M19 52 Yes J
NO >> Repair harness or connector. K
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM) : Diag- L
nosis Procedure INFOID:0000000014585065
M
Regarding Wiring Diagram information, refer to BCS-117, "Wiring Diagram With Color Display" (With color dis-
play) or (BCS-123, "Wiring Diagram With Monochrome Display" (With Monochrome display).
WCS
1.CHECK FUSES AND FUSIBLE LINK

Check if the following BCM fuse or fusible links are blown. O
With Color Display
Signal name Fuses and fusible link No.

P
F (50A)
16 (5A)
Ignition switch ACC 20 (5A)
Ignition switch ON 31 (5A)

With Monochrome Display
Signal name Fuses and fusible link No.

F (50A)
13 (10A)
Ignition switch ACC 20 (5A)
Ignition switch ON 31 (5A)
Is the fuse or fusible link blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit.
NO >> GO TO 2.
Check voltage between combination meter harness connector and ground.
With Color Display
(+)
Voltage
Combination meter (−) Condition
(Approx.)
Connector Terminal
82
M56 OFF
70 Ignition switch posi-
Ground Battery voltage
105 tion ACC
M91
93 ON

(+)
Voltage
Combination meter (−) Condition
(Approx.)
Connector Terminal
74
M87 OFF
65 Ignition switch posi-
Ground Battery voltage
6 tion ACC
M24
33 ON
YES >> GO TO 3.
NO >> Repair harness or connector.
2. Disconnect combination meter connectors.
With Color Display
Combination meter
Continuity
Connector Terminal
M71 1 Ground
M85 52 Yes
M56 79

Combination meter
Continuity
Connector Terminal
39 Ground
M24
40 Yes
M87 79
NO >> Repair harness or connector. A
WCS

METER BUZZER CIRCUIT
METER BUZZER CIRCUIT
Component Function Check INFOID:0000000014250297
1. CHECK OPERATION OF METER BUZZER

CONSULT
1. Select “BUZZER” of “BCM”.
2. Select “LIGHT WARN ALM” in “Active Test” mode.
NO >> Refer to WCS-78, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000014250298
1.CHECK POWER SUPPLY OF COMBINATION METER

Check power supply of combination meter. Refer to MWI-97, "COMBINATION METER (WITH INTELLIGENT
KEY SYSTEM) : Diagnosis Procedure" (with Color Display with Intelligent Key system) or MWI-98, "COMBI-
NATION METER (WITHOUT INTELLIGENT KEY SYSTEM) : Diagnosis Procedure" (with Color Display with-
out Intelligent Key system) or MWI-200, "COMBINATION METER : Diagnosis Procedure" (with Monochrome
Display).
YES >> Replace combination meter. Refer to MWI-137, "Removal and Installation" (with Color Display) or
MWI-217, "Removal and Installation" (with Monochrome Display).
NO >> Repair power supply circuit of combination meter.

PARKING BRAKE SWITCH SIGNAL CIRCUIT
A
1.COMBINATION METER INPUT SIGNAL B

CONSULT
1. Select “Data Monitor” mode of “METER/M&A”.
2. Select “PKB SW”. C
3. Check that the function operates normally according to the following conditions:
Monitor item Condition Status D

When parking brake is applied ON
PKB SW
When parking brake is released OFF
E
F
G
Regarding Wiring Diagram information, refer to WCS-50, "Wiring Diagram - (with Color Display and Intelligent
Key System)" or WCS-56, "Wiring Diagram - (with Color Display and without Intelligent Key System)" or WCS-
62, "Wiring Diagram - (with Monochrome Display)".
H
1.CHECK PARKING BRAKE SWITCH CIRCUIT

I
1. Disconnect combination meter harness connector and parking brake switch harness connector.
2. Check continuity between combination meter harness connector and parking brake switch harness con-
nector.
J
With Color Display and Intelligent Key system
Combination meter Parking brake switch

Continuity
Connector Terminal Connector Terminal K
M106 26 M58 1 Yes
With Color Display and without Intelligent Key system

L
Continuity
Connector Terminal Connector Terminal
M71 26 M58 1 Yes M

Continuity WCS
M24 32 M58 1 Yes
3. Check continuity between parking brake switch harness connector terminal and ground. O
Parking brake switch

Continuity P
M58 1 No

Component Inspection INFOID:0000000014250301
1.CHECK PARKING BRAKE SWITCH

Check continuity between parking brake switch terminal 1 and switch case ground.
Component Terminal Condition Continuity

Parking brake applied Yes
Parking brake switch 1
Parking brake released No
NO >> Replace parking brake switch. Refer to PB-9, "Removal and Installation".

SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
A
1. CHECK COMBINATION METER INPUT SIGNAL B

CONSULT
1. Select “Data Monitor” mode of “METER/M&A”.
2. Select “BUCKLE SW”. C
3. Check that the function operates normally according to the following conditions:
Monitor item Condition Status D

When seat belt LH is fastened OFF
BUCKLE SW
When seat belt LH is unfastened ON
E
F
G
Regarding Wiring Diagram information, refer to WCS-50, "Wiring Diagram - (with Color Display and Intelligent
Key System)" or WCS-56, "Wiring Diagram - (with Color Display and without Intelligent Key System)" or WCS-
62, "Wiring Diagram - (with Monochrome Display)".
H
1.CHECK COMBINATION METER INPUT SIGNAL

1. Turn ignition switch ON. I
2. Check voltage between combination meter harness connector and ground.
J
Combination meter Voltage
Condition
Connector Terminal (Approx.)
When driver seat belt is fastened Battery voltage K

M106 28 Ground
When driver seat belt is unfastened 0V

L
Condition
When driver seat belt is fastened Battery voltage M

M71 28 Ground

WCS
Condition
When driver seat belt is fastened Battery voltage O

M24 12 Ground
P
NO >> GO TO 2.
2.CHECK SEAT BELT BUCKLE SWITCH LH CIRCUIT
2. Disconnect combination meter harness connector and seat belt buckle switch LH harness connector.

3. Check continuity between combination meter harness connector and seat belt buckle switch LH harness
connector.
Combination meter Seat belt buckle switch LH

Continuity
M106 28 B53 1 Yes

Continuity
M71 28 B53 1 Yes

Continuity
M24 12 B53 1 Yes
Combination meter
Continuity
M106 28 No
Combination meter
Continuity
M71 28 No
Combination meter
Continuity
M24 12 No
YES >> GO TO 3.
3.CHECK SEAT BELT BUCKLE SWITCH LH GROUND CIRCUIT
Check continuity between seat belt buckle switch LH harness connector and ground.
Seat belt buckle switch LH

Continuity
B53 2 Yes

Continuity
B53 2 Yes

Continuity
B53 2 Yes

YES >> Inspection End. A
Component Inspection INFOID:0000000014585082
B
1. CHECK SEAT BELT BUCKLE SWITCH LH
1. Turn ignition switch OFF. C
2. Disconnect the seat belt buckle switch LH connector.
3. Check continuity between the seat belt buckle switch LH terminals 1 and 2.
D
Condition Terminal Continuity
When seat belt buckle LH is fastened No
1– 2
When seat belt buckle LH is unfastened Yes E
NO >> Replace the seat belt buckle switch LH. Refer to SB-13, "SEAT BELT BUCKLE : Removal and F
Installation".
WCS

THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
DOES NOT SOUND
MODELS WITH ABS
MODELS WITH ABS : Description INFOID:0000000014250302
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
MODELS WITH ABS : Diagnosis Procedure INFOID:0000000014250303
1.CHECK PARKING BRAKE WARNING LAMP OPERATION

1. Start engine.
2. Check the operation of the brake warning lamp while operating the parking brake.
Condition Warning lamp status

Parking brake applied ON
Parking brake released OFF
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
2. Check the parking brake switch signal circuit. Refer to WCS-79, "Diagnosis Procedure".
YES >> GO TO 3.
Check the parking brake switch. Refer to WCS-80, "Component Inspection".
MODELS WITHOUT ABS
MODELS WITHOUT ABS : Description INFOID:0000000014250304
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
MODELS WITHOUT ABS : Diagnosis Procedure INFOID:0000000014250305
1.CHECK PARKING BRAKE WARNING LAMP OPERATION

1. Start engine.
2. Check the operation of the brake warning lamp while operating the parking brake.

DOES NOT SOUND
Condition Warning lamp status A

Parking brake applied ON
Parking brake released OFF
B
NO >> GO TO 2. C
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Check the parking brake switch signal circuit. Refer to WCS-79, "Diagnosis Procedure".
D
YES >> GO TO 3.
E
Check the parking brake switch. Refer to WCS-80, "Component Inspection".
Is the inspection result normal? F
YES >> GO TO 4.
4.CHECK VEHICLE SPEED SENSOR SIGNAL CIRCUIT G
Check the vehicle speed sensor signal circuit. Refer to MWI-206, "Diagnosis Procedure".
Is the inspection result normal? H
NO >> Repair or replace malfunctioning parts.
I
WCS

THE LIGHT REMINDER WARNING DOES NOT SOUND
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description INFOID:0000000014250306
Light reminder warning does not sound even though headlamp is illuminated.
1.CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION

Check that the headlamps operate normally by operating the combination switch (lighting switch).
Do they operate normally?
YES >> GO TO 2.
NO >> Refer to EXL-114, "Symptom Table" (with LED headlamps) or EXL-279, "Symptom Table" (with
Halogen headlamps).
2.CHECK FRONT DOOR SWITCH LH SIGNAL CIRCUIT
Check the front door switch LH signal circuit. Refer to DLK-97, "Diagnosis Procedure" (with Intelligent Key
system) or DLK-244, "Diagnosis Procedure (With Color Display)" (with Color Display and without Intelligent
Key system) or DLK-245, "Diagnosis Procedure (With Monochrome Display)" (with Monochrome Display).
YES >> GO TO 3.
3.CHECK FRONT DOOR SWITCH LH
Check the front door switch LH. Refer to DLK-98, "Component Inspection" (with Intelligent Key system) or
DLK-246, "Component Inspection" (without Intelligent Key system).
YES >> Replace BCM. Refer to BCS-73, "Removal and Installation" (with Intelligent Key system) or BCS-
144, "Removal and Installation" (without Intelligent Key system).
NO >> Replace front door switch LH. Refer to DLK-179, "Removal and Installation" (with Intelligent Key
system) or DLK-331, "Removal and Installation" (without Intelligent Key system).

THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT
A
SOUND
Description INFOID:0000000014585090
B
• Seat belt warning does not sound even though driver seat belt is not fastened.
• Seat belt warning sounds even though driver seat belt is fastened.
C
1.CHECK WARNING CHIME OPERATION

D
CONSULT
1. Select “BUZZER” of “BCM”.
2. Select “SEAT BELT WARN TEST” in “Active Test” mode.
3. Touch “ON/OFF” to check that the function operates normally. E
Component CONSULT Condition

F
ON
Buzzer SEAT BELT WARN TEST
OFF
Is the inspection result normal? G
YES >> GO TO 2.
NO >> Replace combination meter. Refer to MWI-137, "Removal and Installation" (with Color Display), or
MWI-217, "Removal and Installation" (with Monochrome Display). H
2.CHECK COMBINATION METER INPUT SIGNAL
Check the combination meter input signal. Refer to WCS-81, "Component Function Check".
I
YES >> Replace BCM. Refer to BCS-73, "Removal and Installation" (with Intelligent Key system) or BCS-
144, "Removal and Installation" (without Intelligent Key system).
J
NO >> GO TO 3.
3.CHECK SEAT BELT BUCKLE SWITCH LH CIRCUIT
Check the seat belt buckle switch LH circuit. Refer to WCS-81, "Diagnosis Procedure". K
YES >> GO TO 4.
NO >> Repair or replace harness or connector. L
4.CHECK SEAT BELT BUCKLE SWITCH LH
Check the seat belt buckle switch LH. Refer to WCS-83, "Component Inspection". M
YES >> Replace the combination meter. Refer to MWI-137, "Removal and Installation" (with Color Dis-
play), or MWI-217, "Removal and Installation" (with Monochrome Display). WCS
NO >> Replace the seat belt buckle switch LH. Refer to SB-13, "SEAT BELT BUCKLE : Removal and
Installation".
O

Warning Chime System: Section

Uploaded by

Copyright:

Available Formats

Warning Chime System: Section

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Warning Chime System: Section

Uploaded by

Copyright:

Available Formats

DRIVER INFORMATION & MULTIMEDIA

PRECAUTIONS ................................................... 3 COMMON ITEM (WITH INTELLIGENT KEY SYS-

WITH COLOR INFORMATION DISPLAY ................. 11 COMBINATION METER (COLOR DISPLAY

Revision: November 2016 WCS-1 2017 D23

BCM ................................................................... 49 METER BUZZER CIRCUIT ............................... 78

Revision: November 2016 WCS-2 2017 D23

Revision: November 2016 WCS-3 2017 D23

Transmission assembly (M/T without

No. Component Function

Combination Meter INFOID:0000000014250263

Revision: November 2016 WCS-4 2017 D23

With Monochrome Display E

Revision: November 2016 WCS-5 2017 D23

Without Intelligent Key System

Warning functions Refer to

Revision: November 2016 WCS-6 2017 D23

Without Intelligent Key system H

WARNING CHIME CANCEL CONDITIONS WCS

Revision: November 2016 WCS-7 2017 D23

Signal name Signal source

Combination switch signal Combination switch (Lighting switch) BCM

Driver door switch signal Front door switch LH BCM

Signal name Signal source

Buzzer output signal BCM Combination meter

Without Intelligent Key system

Signal name Signal source

Buzzer output signal BCM Meter control unit

WARNING CHIME : Parking Brake Release Warning Chime INFOID:0000000014250267

(Models without ABS)

WARNING OPERATION CONDITIONS

WARNING CANCEL CONDITIONS

Without Intelligent Key system L

WARNING CANCEL CONDITIONS

Revision: November 2016 WCS-9 2017 D23

Signal name Signal source

Signal name Signal source

Buzzer output signal BCM Combination meter

Revision: November 2016 WCS-10 2017 D23

Test order Test item Description

Revision: November 2016 WCS-11 2017 D23

Blue Red Pink

*2: Error Code

Item Code Description Action to take/Reference

Revision: November 2016 WCS-12 2017 D23

— 0 Displays “0” constantly. —

— 0 Displays “0” constantly. —

How to Reset Error Code

Revision: November 2016 WCS-13 2017 D23

METER/M&A Diagnosis mode Description

Self Diagnostic Result

Revision: November 2016 WCS-14 2017 D23

Revision: November 2016 WCS-15 2017 D23

Work support item Description

WITH MONOCHROME INFORMATION DISPLAY

Revision: November 2016 WCS-17 2017 D23

*1: Error Code 1

Item Code Description Action to take/Reference

Revision: November 2016 WCS-18 2017 D23

*2: Error Code 2