Diq S 282 284

OPERATING MANUAL
ba76188e01 03/2017
DIQ/S 282
DIQ/S 284
IQ SENSORNET SYSTEM 28X FOR 2 OR 4 DIGITAL IQ SENSORS
IQ SENSORNET System 28X
Contact YSI
1725 Brannum Lane
Yellow Springs, OH 45387 USA
Tel: +1 937-767-7241
800-765-4974
Email: [email protected]
Internet: www.ysi.com
Copyright © 2017 Xylem Inc.
2 ba76188e01 03/2017
DIQ/S 28X Contents
Contents
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Structure and function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.2 Functions in the IQ SENSORNET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.3 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.3.1 USB interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.3.2 Ethernet interface (DIQ/S 28X-E[F]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.3.3 Fieldbus interface (DIQ/S 28X -MOD, -PR, -EF) . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.4 Behaviour of the system to a power failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.1 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.1.1 Safety information in the operating manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.1.2 Safety signs on the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.1.3 Further documents providing safety information ....................... 16
2.2 Safe operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.1 Authorized use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.2 Requirements for safe operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.3 Unauthorized use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.3 User qualification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1 Scopes of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2 Basic principles of installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.1 Requirements of the measurement location . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3 Safety requirements of the electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4 Installation guidelines for lightning protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.5 Drawing up the power rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.6 Connecting the sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.7 On-site mounting of the DIQ/S 28X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.7.1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.7.2 Mounting on a mounting stand with the SSH/IQ sun shield . . . . . . . . . . . . . . . . . 29
3.7.3 Mounting under the SD/K 170 sun shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.7.4 Top hat rail mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.7.5 Panel mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.8 Electrical connections: General instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.9 Connecting the voltage supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.9.1 DIQ/S 28X (line power version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.9.2 DIQ/S 28X[-XX]/24V (24 V version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.10 Connections to the relay and current outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.10.1 General installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.10.2 Usage of the auxiliary voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
ba76188e01 03/2017 3
Contents DIQ/S 28X
3.11 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.12 Installation examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
3.12.1 Connecting two sensors without compressed air cleaning . . . . . . . . . . . . . . . . . . 49
3.12.2 Connecting two sensors with compressed air cleaning . . . . . . . . . . . . . . . . . . . . 50
3.12.3 Connection of a sensor that is located at a distance
(without compressed air cleaning) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3.13 Figures of the terminal strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.1 Operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.1.1 Overview of the operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.1.2 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4.1.3 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
4.2 General operating principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
4.2.1 Navigating in menus, lists and tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.2.2 Entering texts or numerals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.3 Access to the IQ SENSORNET with active access control . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.4 Display of current measured values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.4.1 Displaying a single measured value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4.4.2 Displaying four measured values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4.4.3 Displaying eight measured values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4.4.4 Displaying recorded measured values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
4.4.5 Transmitting recorded measurement data to a PC . . . . . . . . . . . . . . . . . . . . . . . . 66
4.5 Messages and log book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.5.1 Message types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.5.2 Log book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
4.5.3 Viewing detailed message texts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
4.5.4 Acknowledge all messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
4.6 Calibration data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.6.1 Calibration entries in the log book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.6.2 Calibration history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.7 Status info of sensors and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4.8 General course when calibrating, cleaning, servicing or repairing an IQ sensor .... 74
4.8.1 Maintenance condition of IQ sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.8.2 Switching on the maintenance condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
4.8.3 Switching off the maintenance condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
4.9 USB interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
4.9.1 Saving IQ SENSORNET data to a USB memory device . . . . . . . . . . . . . . . . . . . . . 77
4.9.2 Restore system configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
4.10 Info on software versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
4.11 Software-Update for DIQ/S 28X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5 Settings/setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
5.1 Selecting the language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
5.2 Terminal settings of the DIQ/S 28X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
5.3 Access control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5.3.1 Activating the access control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
4 ba76188d01 03/2017
DIQ/S 28X Contents
5.3.2 Activating the instrument block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

5.3.3 Electronic key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
5.3.4 Access to the IQ SENSOR NET with active access control . . . . . . . . . . . . . . . . . . 86
5.4 Editing the list of sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
5.4.1 Entering / editing a name for an IQ sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
5.4.2 Changing the display position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
5.4.3 Erasing inactive sensor datasets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
5.5 Settings for sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
5.6 Sensor-sensor link
(automatic offset of an influencing quantity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
5.6.1 Establishing the sensor-sensor link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
5.6.2 Erasing a Sensor-sensor link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
5.7 Editing the list of outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
5.7.1 Entering / editing the name of an output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
5.7.2 Erasing an inactive dataset for an MIQ output module . . . . . . . . . . . . . . . . . . . . 96
5.7.3 Output links/settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
5.8 Alarm settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
5.8.1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
5.8.2 Setting up / editing alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
5.8.3 Alarm output to display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
5.8.4 Alarm output as relay action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
5.8.5 Alarm message as Email (variant -E, EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
5.9 System settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5.9.1 Changing the password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5.9.2 Setting the date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
5.9.3 Location altitude / average air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
5.9.4 TCP/IP settings (variant -E, EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
5.9.5 email (variant -E, EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.9.6 Settings bus interfaces (variant -E, EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5.9.7 Function code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5.10 Measured value logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5.10.1 Setting the recording interval (dt) and recording duration (Dur.) . . . . . . . . . . . . 109
6 Ethernet connection (variant -E, -EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

6.1 Configuring the Ethernet network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
6.1.1 Communication in a local network (LAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
6.1.2 Communication on the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
6.2 Ethernet connection if mounted at an open air test site (DIQ/S 28X-E[F]) . . . . . . . . . . . 116
6.3 Establishing the connection with the DIQ/S 28X via a network . . . . . . . . . . . . . . . . . . . . 116
6.3.1 Opening the IQ WEB CONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
6.3.2 IQ WEB CONNECT Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
6.3.3 IQ WEB CONNECT DatalogTransfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
6.3.4 IQ WEB CONNECT ConfigSaveLoad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
6.4 Communication with fieldbuses (DIQ/S 28X[-XX]-EF) . . . . . . . . . . . . . . . . . . . . . . . . . . 120
6.5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
6.6 Technical network terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
ba76188d01 03/2017 5
Contents DIQ/S 28X
7 Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
7.1 Outputs of the System 28X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
7.2 Basic information on relay functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
7.2.1 Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
7.2.2 Limit indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
7.2.3 Proportional output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
7.3 Entering / editing the name of an output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
7.4 Linking the output with a sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
7.5 Deleting a link with an output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
7.6 Setting the relay outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
7.6.1 Relay action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
7.6.2 System monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
7.6.3 Sensor monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
7.6.4 Limit indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
7.6.5 Frequency controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
7.6.6 Pulse-width output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
7.6.7 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
7.6.8 Sensor-controlled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
7.6.9 Manual control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
7.6.10 Alarm contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
7.7 Setting the current outputs (variant -CR3, CR6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
7.7.1 Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
7.7.2 PID controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
7.7.3 Fixed current value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
7.8 Checking the condition of the outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
7.9 Behavior of linked outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
7.9.1 Behavior in case of error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
7.9.2 Behavior in non-operative condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
7.10 Maintenance condition of the sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
7.10.1 Switching on the maintenance condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
7.10.2 Switching off the maintenance condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
8 Maintenance and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

8.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
8.2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
9 What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160

9.1 Information on errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
9.2 Errors: causes and elimination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
9.3 Replacing system components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
9.3.1 Replacing passive components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
9.3.2 Adding and replacing IQ sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
9.3.3 Adding and replacing DIQ or MIQ output modules . . . . . . . . . . . . . . . . . . . . . . . 164
10 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

10.1 DIQ/S 282, DIQ/S 284 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
6 ba76188d01 03/2017
DIQ/S 28X Contents
10.2 General data of MIQ modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175

10.3 DIQ/JB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
10.4 DIQ/CHV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
10.5 Space required by mounted components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
11 Accessories and options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
12 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
12.1 Explanation of the message codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
12.1.1 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
12.1.2 Informative messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
13 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
14 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

14.1 Ordering & Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
14.2 Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
ba76188d01 03/2017 7
DIQ/S 28X
8 ba76188d01 03/2017
DIQ/S 28X Overview
1 Overview
1.1 Structure and function
The IQ SENSORNET System 28X is a modular measuring system for online anal-
ysis.
PC, Tablet PC, Smartphone, ...

via IQ WEB CONNECT
Webserver
email
Internet SPS
-EF (Ethernet fieldbus)

DSL EtherNet/IP
TM
UMTS Modbus TCP

LTE
Profinet
Router
(Industrial) Ethernet-LAN
SPS
Data Modbus RTU SPS

Transfer
PROFIBUS DP
USB stick
RS 485 RS 485
[-E], [-EF] * Radio

USB [-MOD] * [-PR] * Funkmodul
Radio module 100 m
Funkmodul
Radio module
Universal Transmitter DIQ/S 28x
IQ SENSOR NET (Daten + Energie) IQ SENSOR NET
IQ Sensor Power supply Inputs Eingänge

Outputs IQ Sensor Terminal
module mA Relays
mA
mA (CRx)
Valve (MIQ/CHV)
IQ SENSOR NET System 28x ISLAND 1 IQ IQ
SENSOR
SENSOR
NET
NET
ISLAND
Insel 22
Fig. 1-1 Functional units of the IQ SENSORNET System 28X

* depending on the variant, one of these interfaces is available at the system
The functional units are connected with one another via a common line. The line
consists of two wires and a shield. It transports digital information between the
ba76188d01 03/2017 9
Overview DIQ/S 28X
Universal Transmitter and the other modules. At the same time it is used for the
power supply of all components.
Sensors All main and secondary measured parameters of the sensors connected can be
displayed and administrated. Each sensor is automatically recognized after
being connected and immediately starts measuring.
Universal The Universal Transmitter DIQ/S 28X[-XX] provides the core functions of the
Transmitter IQ SENSORNET system (power supply, controller, terminal, relays).
The variants of the Universal Transmitters DIQ/S 28X enhance the
IQ SENSORNET System 28X by additional functions and interfaces.
Overview Function DIQ/S 28X Variant(s)

IQ SENSORNET
System 28X Line power Supply voltage 100 ... 240 V [-XX]
variants
24 V [-XX]/24V
Basic func- Terminal [-XX]
tions
Controller [-XX]
Power supply module [-XX]
Relay [-XX]
USB interface [-XX]
SENSORNET interface [-XX]
Extended Current outputs -CR3[-XX], -CR6[-XX]
functions
More inter- Ethernet interface [-CRx]-E, -EF
faces
Fieldbus interface for connection to existing process control
systems:
 Modbus -MOD
 Profibus PR
 Ethernet fieldbuses -EF
Sensors Max. 2 sensors DIQ/S 282 [-XX]
Max. 4 sensors DIQ/S 284 [-XX]
10 ba76188d01 03/2017
DIQ/S 28X Overview
Components to Function Component

extend the sys-
tem? Passive Power supply module MIQ/PS
compo-
nents Radio link (with power supply unit) MIQ/WL PS
Branching DIQ/JB, MIQ/JB
(interfaces for sensors)
Active Relay DIQ/CR3, MIQ/CR3,
compo- MIQ/R6
nents
Current outputs DIQ/CR3, MIQ/CR3,
MIQ/C6
Current inputs MIQ/IC2
More Valve output DIQ/CHV, MIQ/CHV Plus
compo-
nents
Maximum extensibility of the system:

 Passive components: no limitation
 Valve outputs: maximum 1 output per sensor
 Active components: 2
Example:
The variant DIQ/S 284-CR6[-XX] already contains one active
component (DIQ/CR3). The system can still be extended by one
active component.
Branches To be able to connect more sensors than there are SENSORNET connections
available at a Universal Transmitter DIQ/S 28X, use the branching module DIQ/
JB (accessory). The DIQ/JB branching module is a simple passive module for
the branching of IQ SENSOR NET lines.
Relay and current The relay and current outputs can be linked with sensors. Linked outputs can be
outputs used to monitor sensors and for the output of measured values.
A relay output can be programmed as:
 Monitoring relay
 Limit monitor
 Proportional output of measured values (pulse width or frequency output)
 Control unit of a sensor cleaning system driven by compressed air.
A current output (system variant or extra component -CR3 or -CR6) is program-

mable as:
 Analog output
 PID controller
ba76188d01 03/2017 11
Overview DIQ/S 28X
For quick orientation, the states of all relay and current outputs are clearly indi-
cated on the display.
Compressed air- The DIQ/S 28X Universal Transmitter is prepared for the compressed air-driven,
driven cleaning time-controlled sensor cleaning function. For this, a DIQ/CHV valve module and
system if necessary a CH cleaning head is required per sensor (both available as acces-
sories). The cleaning procedure is controlled by the Universal Transmitter. The
Universal Transmitter provides the supply voltage and control relay for the
compressed air valve in the DIQ/CHV valve module. This enables a simple
setup and uncomplicated wiring.
Alternatively, the MIQ/CHV PLUS valve module can be installed in the system.
It combines the relay, valve and valve power supply in one MIQ enclosure. Thus,
no additional wiring is required, which makes installation easier especially if the
distance between the Universal Transmitter and sensor is great.
If necessary, an additional power pack can be added to supply sensors with high
power consumption (e.g. UV/VIS sensor).
Example of a
simple system Universal Transmitter
DIQ/S 28X-CR3
DIQ/JB
IQ Sensors, digital
Fig. 1-2 Simple systems with one and two sensors
12 ba76188d01 03/2017
DIQ/S 28X Overview
1.2 Functions in the IQ SENSORNET

The functions of the IQ SENSORNET are provided by the system (DIQ/S 28X)
and the retrofitting components. Details on the functions listed can be found in
the relevant system or components operating manuals.
Function Operating manual

Alarm messages System
Analog output System
Data logging System
Data logging IQ WEB CONNECT
Data transmission IQ WEB CONNECT
Data communication (Profibus DP, Modbus RTU, Fieldbus linking
Profinet, Modbus TCP, EtherNet/IP)
Data communication Ethernet System, fieldbus linking
Data logger System
Webserver, Email server System
Frequency output System, relay output module
Limit monitor System, relay output module
Calibration history System
List of outputs, list of sensors System
Log book System
Log book (messages from components) IQ Sensor, output module
Measured value representation (4 types) System
Password System
PID controller System, current output module
Pulse-width output System, relay output module
Sensor cleaning System, relay output module
Valve module, Cleaning Air Box
Local settings System
Daily load diagram, weekly load diagram, monthly System
load diagram
Monitoring functions (sensors, system) System, current or relay output module,
fieldbus linking
ba76188d01 03/2017 13
Overview DIQ/S 28X
1.3 Interfaces
1.3.1 USB interface
The USB interface of the DIQ/S 28X provides the following functions:
 Connection of a USB memory for the transfer of data (see section 4.9)
– Measured data
– Calibration data
– Configuration data
– Log book
– IQ LabLink data
 Connection of a USB memory device to be used as an electronic key for sim-
ple access to the system when access control is switched on (see
section 5.3.3)
 Connection of a USB hub for the reproduction of the USB interface.
NOTE:
The USB interface is designed for USB memory devices with a maximum
power consumption of 1 watt. USB memory devices with a higher power
consumption have to be supplied with power by an extra power supply. If
these instructions are not complied with, the availability of the system can
be adversely affected.
The USB interface is equipped with a protective cover.

Only remove the protective cover when you want to connect a USB
device. Immediately close the USB connection again when you
have removed the USB device.
When the USB connection is open, there is a danger of corrosion.
1.3.2 Ethernet interface (DIQ/S 28X-E[F])
The Ethernet interface of the DIQ/S 28X -E[F] provides the following functions:
 Integration into an Ethernet network (see section 6)
 Monitoring and remote control via the Internet (IQ WEB CONNECT)
 E-mail feature
14 ba76188d01 03/2017
DIQ/S 28X Overview
1.3.3 Fieldbus interface (DIQ/S 28X -MOD, -PR, -EF)
The following variants of the DIQ/S 28X have a fieldbus interface:
DIQ/S 28X variant Fieldbus connection

DIQ/S 28XPR PROFIBUS DP
DIQ/S 28X-MOD Modbus RTU/RS 485
DIQ/S 28X[-CRx]-EF Ethernet fieldbuses
(EtherNet/IP™, Profinet, Modbus TCP)
1.4 Behaviour of the system to a power failure

 The system configuration is permanently retained. It consists of the following
settings:
– Sensor settings
– Settings and links of the relay outputs
– Settings and links of the current outputs
– System settings (display language, air pressure/altitude, passwords etc.)
 Linked relay outputs switch to the non active condition (open).
 Linked current outputs switch to the non active condition (0 mA).
 A restart is carried out automatically when the power returns. The continues
working with the settings of the time prior to the power failure.
If the power failure lasted several hours the system clock has to be reset.
ba76188d01 03/2017 15
Safety DIQ/S 28X
2 Safety
2.1 Safety information
2.1.1 Safety information in the operating manual
This operating manual provides important information on the safe operation of

the product. Read this operating manual thoroughly and make yourself familiar
with the product before putting it into operation or working with it. The operating
manual must be kept in the vicinity of the product so you can always find the
information you need.
Important safety instructions are highlighted in this operating manual. They are
indicated by the warning symbol (triangle) in the left column. The signal word
(e.g. "CAUTION") indicates the level of danger:
WARNING
indicates a possibly dangerous situation that can lead to seri-
ous (irreversible) injury or death if the safety instruction is not
followed.
CAUTION
indicates a possibly dangerous situation that can lead to slight
(reversible) injury if the safety instruction is not followed.
NOTE
indicates a situation where goods might be damaged if the actions mentioned
are not taken.
2.1.2 Safety signs on the product
Note all labels, information signs and safety symbols on the product. A warning
symbol (triangle) without text refers to safety information in this operating
manual.
2.1.3 Further documents providing safety information
The following documents provide additional information, which you should

observe for your safety when working with the measuring system:
 Operating manuals of other components of the IQ SENSORNET system
(power supply modules, accessories)
 Safety datasheets of calibration and maintenance equipment (e.g. cleaning
solutions).
16 ba76188d01 03/2017
DIQ/S 28X Safety
2.2 Safe operation
2.2.1 Authorized use
The authorized use of the DIQ/S 28X Universal Transmitter consists of its use
in online analysis. Only the operation and running of the sensor according to the
instructions and technical specifications given in this operating manual is autho-
rized (see chapter 10 TECHNICAL DATA). Any other use is considered unauthor-
ized.
2.2.2 Requirements for safe operation
Note the following points for safe operation:

 The product may only be operated according to the authorized use specified
above.
 The product may only be operated under the environmental conditions men-
tioned in this operating manual.
 The product may only be supplied with power by the energy sources men-
tioned in this operating manual.
 The product may only be opened if this is explicitly described in this operating
manual (example: connecting electrical lines to the terminal strip).
2.2.3 Unauthorized use
The product must not be put into operation if:

 it is visibly damaged (e.g. after being transported)
 it was stored under adverse conditions for a lengthy period of time (storing
conditions, see chapter 10 TECHNICAL DATA).
2.3 User qualification

Target group The IQ SENSORNET System 28X was developed for online analysis. Some main-
tenance activities, e.g. changing the membrane caps in D.O. sensors, require
the safe handling of chemicals. Thus, we assume that the maintenance
personnel is familiar with the necessary precautions to take when dealing with
chemicals as a result of their professional training and experience.
Special user The following installation activities may only be performed by a qualified electri-
qualifications cian:
 Connection of the DIQ/S 28X to the power supply.
 Connection of external, line voltage-carrying circuits to relay contacts (see
module manual of the relay output module).
ba76188d01 03/2017 17
Installation DIQ/S 28X
3 Installation
3.1 Scopes of delivery
The following parts are included in the scope of delivery:
 DIQ/S 28X Universal Transmitter
 Accessory kit with:
– Contact carrier with screws
– ISO cap nuts with screws and ring washers
– Cable glands with sealing gaskets
 Operating manual.
3.2 Basic principles of installation
3.2.1 Requirements of the measurement location
The measurement location must meet the environmental conditions specified in

section 10.1 DIQ/S 282, DIQ/S 284.
Controlled Work on the open instrument (e.g. during mounting, installation, maintenance)
environmental may only be carried out under controlled environmental conditions:
conditions
Temperature + 5 °C ... + 40 °C (+ 41 ... +104 °F)
Relative humidity ≤ 80 %
3.3 Safety requirements of the electrical installation

Electrical equipment (such as motors, contactors, cables, lines, relays,
switches, instruments) must meet the following requirements:
 Compliance with national regulations (e.g. NEC, VDE and IEC)
 Suitability for the electrical conditions at the place of installation
– Maximum operational voltage
– Maximum operational current
 Suitability for the ambient conditions at the place of installation
– Temperature resistance (minimum and maximum temperature)
– Stability against UV light in the case of outdoor usage
– Protection against water and dust (IP type of protection).
 Suitable fuse protection of the electrical circuit
– Overcurrent protection devices
18 ba76188d01 03/2017
DIQ/S 28X Installation
(according to the technical data of the instrument input or output)

– Overvoltage limitations of overvoltage category II
 Suitable external separator (e.g. switch or circuit-breaker) for the power sup-
ply of permanently installed instruments with separate power connection
– compliant with the following regulations
- IEC 60947-1
- IEC 60947-3
– in the vicinity of the instruments (recommendation)
 Flame resistant (cable and lines),
compliant with the following regulations
– UL 2556 VW-1 (for USA, Canada)
– IEC 60332-1-2 (outside the USA, Canada)
3.4 Installation guidelines for lightning protection

During the use of the DIQ/S 28X universal transmitter, particularly in outdoor
areas, adequate protection against (electrical) surges must be provided. A surge
is a summation phenomenon of surge voltage and surge current. It is generated
through the indirect effect of a lightning event or switching operation in the
mains, in the grounding system and in information technology lines.
To be adequately protected against the damaging effects of surges, an inte-
grated concept of the following protective measures is required:
 internal device-related protective measures and
 external protective measures of the installation environment.
The internal device-related protective measures are already integrated in the

YSI online instrumentation as so-called 'lightning protection' (see
chapter 10 TECHNICAL DATA).
The external protective measures of the installation environment can be carried
out with respect to the following guidelines:
1 All lines of systems must be
a) installed inside (or else close to) the grounded metallic mounting construc-
tions, e.g. handrails, pipes and posts if possible
b) or, particularly in the case of longer lines, laid in the ground.
Background: The formation of highly lightning hazardous inductive loops be-

tween the cables and ground is avoided through the low clearance of the
grounded metal construction or by installation in the ground.
2 Only IQ cable material may be used. This cable material is an important pre-
requisite for the hazard-free discharging of the surge without inadmissibly
high overvoltages developing along the line at the same time that could have
a damaging effect on the individual components.
3 All metallic mounting constructions (handrails, pipes, posts etc.) on which
ba76188d01 03/2017 19
DIQ modules are installed must be connected to the local potential equaliza-
tion system and the grounding system or must be individually sufficiently
grounded locally according to the codes of practice.
For the individual grounding of the measuring point the mounting construc-
tion must be solidly connected by means of a large-area auxiliary electrode
with the measuring medium.
Metallic control shafts/pipes and other large-area metallic bodies that reach
into the measuring medium are, for example, ideal for use in the grounding
of the mounting construction.
This creates a set path for the main surge. As a result it is possible to avoid
the surge being discharged via the cable and via the valuable sensor in the
measuring medium.
4 It is recommended to attach a metallic or nonmetallic sun shield to each out-
side location of the DIQ modules. Sun shields protect the electric field lines
in the area of the DIQ module due to an advantageous development of the
electrical field lines in the area of the MIQ module and promote the dissipa-
tion of the surge via the mounting construction.
5 The line voltage for the supply of the IQ SENSORNET must comply with over-
voltage category II. Generally this is ensured through the public operator of
the power supply networks. In company-owned networks, e.g. in all power
supply systems owned by wastewater treatment plants, this must be kept
separate by a potential equalization and a surge protection system for the
plant.
6 One part of the safety and lightning protection concept is based on high-
grade protective insulation of the IQ SENSORNET. It does not have or require
any protective ground conductor or earth terminal. Avoid any direct contact
of any SENSOR connections or the metallic sensor enclosures with the local
grounding or potential equalization system and with metallic construction el-
ements (see point 8).
7 Additional external lightning protection measures, e.g. the use of overvoltage
surge arresters, are not necessary for protection against the indirect effects
of lightning and could possibly result in malfunctions.
8 For the realization of the internal lightning protection of the system (e.g.
wastewater treatment plant control stands) and for the protection of external
resources, cable entry points into buildings or distributions coming from the
DIQ/S 28X must be carried out as follows:
– The shield of SNCIQ or SNCIQ-UG cables can be connected to the local
potential equalization with a gas overvoltage arrester. Use shield clamps
for the contacting of the shield. The shield of the cable must not be opened
under any circumstances.
– 0/4-20 mA interfaces must be realized with shielded cables. The cable
shield must be connected directly to the potential equalization(s) provided.
If plant potential equalization systems are provided on both sides, the
shield must also be connected on both sides. The inner conductors must
have no contact with the potential equalization.
– Relay lines should be connected to the local potential equalization in order
20 ba76188d01 03/2017
to provide general and consistent protection via gas overvoltage surge

arresters.
3.5 Drawing up the power rating

General The IQ SENSORNET supplies all components with low voltage as well as digital
information communication via a shielded 2-wire line.
Because of this characteristic the energy consumption of all components must
be taken into account (power rating) when planning an IQ SENSORNET system.
The energy consumption determines whether an additional power module is
necessary.
Only IQ SENSORNET products may be used in the IQ SENSORNET.
Power rating - All components in the system require a specific level of electrical power for oper-
why? ation. Thus, it is necessary to draw up a power rating after selecting the desired
components. At the same time, this can determine whether the entire power
requirement of all components (consumers) is covered by the internal power
supply module of the Universal Transmitter. If this is not the case, the power
available in the system must be increased by further MIQ power supply
modules.
To operate the DIQ/S 28X safely, the power rating must meet the following
condition for continuous operation and for power peaks:
Sum of the power requirement ≤ Sum of the power delivery

(continuous) (continuous)
Sum of the power requirement ≤ Sum of the power delivery
(peak) (peak)
The power rating provides an initial guide value. In specific limiting

cases, the power supply may be insufficient despite the positive
power rating.
Example: Temperatures above 47 °C (117 ° F) reduce the available
power output of the DIQ/S 28X (see TEMPERATURE DEPENDENCY
(DEGRADATION) OF THE MAXIMUM ALLOWED P(CONTINUOUS), page 25).
The reduced power output may possibly have to be compensated
for with further MIQ power supply modules.
Maximum allowed The maximum allowed power delivery of the power supply components of the
power delivery of IQ SENSORNET is given in the following table:
IQ SENSORNET
components
ba76188d01 03/2017 21
Component Power delivery [W]

Continuous Peak
IQ sensors
DIQ/S 28X 6.5 12
MIQ/PS 18 18
MIQ/WL PS 7 7
The power requirement of the individual components is listed in the following

table:
Power requirement Component Power requirement [W]

of IQ SENSORNET Continuous Peak
components
IQ sensors
SensoLyt® 700 IQ (SW) 0.2 0.2
TriOxmatic® 70x IQ (SW) 0.2 0.2
FDO® 70x IQ (SW)(H) 0.7 0.7
®
TetraCon 700 IQ (SW) 0.2 0.2
VisoTurb® 700 IQ (SW) 1.5 1.5
ViSolid® 700 IQ (SW)(H) 1.5 1.5
® Plus
AmmoLyt 700 IQ 0.2 0.2
® Plus 700
NitraLyt IQ 0.2 0.2
VARiON® Plus 700 IQ 0.2 0.2
Spectral sensors 3.5 8

XXXVis® 7YY IQ
(e.g. NiCaVis® 705 IQ )
UV 70x IQ NOx 3.5 8
UV 70x IQ SAC 3.5 8
IFL 700 IQ 3.0 5.5
IFL 701 IQ 3.0 3.0
P 700 IQ (MIQ/WCA 232) 0.5 0.5
MIQ modules
MIQ/JB 0.1 0.1
MIQ/CR3 2.3 3.0
DIQ/CR3 2.3 3.0
MIQ/C6 2.0 3.0
MIQ/R6 1.2 1.5
22 ba76188d01 03/2017
Component Power requirement [W]

Continuous Peak
MIQ/IC2 0.2 0.2
+ 2.2 W per con- + 2.2 W per con-
nected WG 21 A7 nected WG 21 A7
power supply/iso- power supply/iso-
lator lator
DIQ/CHV 2.2 x rel. turn-on 2.2 x rel. turn-on
duration * duration *
MIQ/CHV PLUS 0.2 + 2.3 x TD (rel. 2.5
turn-on duration) *
MIQ/WL PS 0.6 0.6
* The following text informs about allowing for the relative turn-on duration (TD)
Allowing for the Valves usually switch on periodically for a limited time and then require the
relative on-time in nominal power. Crucial for the load on the power unit of the DIQ/S 28X is the
valves time averaged (effective) power requirement that depends on the relative on-
time, OT:
Relative on-time OT = tOn / (tOn + tOff)
The effective power requirement is the product of the nominal power of the valve
component and the relative on-time:
P = Pnominal * OT
Since OT is always < 1, the effective power requirement is always smaller than
the nominal power of the valve component.
For the control of sensor cleaning systems operated by compressed

air, a relative on-time of max. 0.1 has been adopted in practice.
Determining the From the value determined for the power requirement, determine the number of
number of the MIQ power supply modules as follows:
additional
MIQ power supply Total power requirement P Number of additionally required
modules MIQ/PS power supply modules
P (continuous) P (peak)
P(c) ≤ 6.5 W P(p) ≤ 12 W -
P(c) ≤ 6.5 W P(p) > 12 W 1
P(c) > 6.5 W 1
ba76188d01 03/2017 23
Calculation example:
Example configuration 1 Power requirement [W]

(component)
Continuous Peak
+ 1 FDO® 700 IQ 0.7 0.7
NitraVis® 705 IQ 3.5 8
MIQ/CHV PLUS (TD = 0.9) 2.27 2.45
(= 0.2 + 2.3 x (= 0.2 + 2.5 x
0.9) 0.9)
Total power requirement P [W] P (continuous): P (peak):
(sum of the components) 6.47 11.15
Result:
Total power requirement P (continuous) < 6.5 W
Total power requirement P (peak) < 12 W
No additional power supply module is required.
Example configuration 2 Power requirement [W]

(component)
Continuous Peak
+ DIQ/CR3 2.3 3.0
also as element of the
DIQ/S 284-CR6[-XX]
+ 1 FDO® 700 IQ 0.7 0.7
NitraVis® 705 IQ 3.5 8
MIQ/CHV PLUS (OT = 0.9) 2.27 2.45
(= 0.2 + 2.3 x (= 0.2 + 2.5 x
0.9) 0.9)
Total power requirement P [W] P (continuous): P (peak):
(sum of the components) 8.77 14.15
Result:
Total power requirement P (continuous) > 6.5 W
Total power requirement P (peak) > 12 W
An additional power supply module is required.
24 ba76188d01 03/2017
Temperature If the DIQ/S 28X is operated at an ambient temperature below 47 °C (117 °F),
dependency the operator has to make sure that the total power requirement P (continuous)
(degradation) is not more than 6.5 W.
of the maximum If the DIQ/S 28X is operated at an ambient temperature above 47 °C (117 °F),
allowed the allowed total power requirement P (continuous) is linearly reduced to 0.7 W
P(continuous) at 55 °C (131 °F).
For the short-term total power requirement P (peak), no temperature

dependency has to be taken into account.
Power output [W]
7
6,5
6
1
0,7
0
-30 -20 .................. 0 ............ +46 48 50 52 54 56

Ambient temperature[°C]
Permissible ambient temperature -20 … +55 °C
Fig. 3-1 Degradation line of the line power variant DIQ/S 28X[-XX]
ba76188d01 03/2017 25
If the DIQ/S 28X [-XX]/24V is operated at an ambient temperature below 47 °C

(117 °F), the operator has to make sure that the total power requirement P (con-
tinuous) is not more than 6.5 W.
If the DIQ/S 28X[-XX]/24V is operated at an ambient temperature above 47 °C
(117 °F), the allowed total power requirement P (continuous) is linearly reduced
to 4 W at 55 °C (131 °F).
Power output [W]
6,5
5,5
4,5
-30 -20 .................. 0 ............ +46 48 50 52 54 56

Ambient temperature[°C]
Permissible ambient temperature -20 … +55 °C
Fig. 3-2 Degradation line of the 24V variant DIQ/S 28X[-XX]/24V
3.6 Connecting the sensor

The sensors are connected to a SENSORNET connector of the DIQ/S 28X.
General instal- Lines must always be installed separately at a minimum distance of 20 cm from
lation instructions other lines that carry a voltage greater than 60 V.
The free end of the sensor cable was stripped in the factory and all the wires are
fitted with wire end sleeves.
Tools  Phillips screwdriver
 Small screwdriver.
NOTE
The sensor cable may only be connected to the SENSORNET connections. No
wire of the cable may be connected with an external electrical potential. Other-
wise, malfunctions could occur.
26 ba76188d01 03/2017
1 On the left-hand side of the DIQ/S 28X, remove the two countersunk
screws and open the enclosure.
SENSORNET
X3 X2 X1
2
GREEN
SHIELD
RED
1
SENSORNET 1
3
SNCIQ SACIQ
SNCIQ/UG
Fig. 3-3 Connecting the cable (example DIQ/S 28XCR3)
2 Screw the cable gland (no. 029 212, pos. 1 in Fig. 3-3) with the sealing
(pos. 2) into the housing at the mounting position for the SENSORNET
connection (see label on the bottom of the housing)
3 Loosen the cap nut (pos. 3 in Fig. 3-3).
4 Feed the sensor cable through the cable gland into the enclosure.
ba76188d01 03/2017 27
X3 X2 X1
RED
SHIELD
GREEN
SENSORNET
schwarz
rot grün
Sensor
Fig. 3-4 SENSORNET connector (example DIQ/S 28X CR3)
5 Connect the cable ends to the terminal strip. At the same time, look out
for the designations of the terminals (red / shield / green).
6 Tighten the cap nut (pos. 3 in Fig. 3-3).
7 Close the enclosure.
The complete assignment of the terminal strip is shown in

section 3.13.
For further instructions on the mounting of the sensor at the applica-

tion location, please refer to the relevant manual (immersion depth,
etc.).
3.7 On-site mounting of the DIQ/S 28X
3.7.1 General information
The universal transmitter DIQ/S 28X is designed for stationary installation. With
the aid of mounting accessories, the setup can be adjusted to meet various
requirements.
28 ba76188d01 03/2017
NOTE
Components installed outside must always be protected by a sun shield against
the effects of the weather (snow, ice and direct solar radiation). Otherwise, mal-
functions can result. Always mount the universal transmitter in an upright posi-
tion. Do not under any circumstances install the universal transmitter without
rain protection with the lid facing upwards (danger of retained humidity and pen-
etration of moisture).
NOTE
No contact base may be mounted on the back of the module (danger of short-
circuit!) if the module is mounted on a wall, a sun shield, or a top hat rail.
Installation The most important types of installation for the universal transmitter are
options described in the following chapters:
 Mounting with sun shield SSH/IQ:
(see section 3.7.2).
 Mounting to the sun shield SD/K 170
The sun shield SD/K 170 provides room for the universal transmitter. The sun
shield can be mounted to round or square section pipes (e.g. rails) with the
aid of the MR/SD 170 mounting kit (section 3.7.3).
 Wall mounting:
The universal transmitter is permanently fixed to a wall. For wall mounting,
use the WMS/IQ mounting set (see chapter 11 ACCESSORIES AND OPTIONS).
 Panel mounting:
The universal transmitter is mounted in the aperture of a switch panel. The
dimensions of the aperture are 138 mm x 138 mm. The panel may not be
thicker than 10 mm (section 3.7.5).
To install the interface (MOD, PR, E, EF) of the DIQ/S 28X [-MOD], [-PR], [-
E(F)] behind the panel, use the PMS/IQ-X accessory (see section 11).
 Top hat rail mounting:
The universal transmitter is mounted on a 35 mm top hat rail with the aid of a
bracket, e.g. in a control cabinet. The connection can be released again with
one simple movement (section 3.7.4).
The following chapters describe the mounting of the universal transmitter.
3.7.2 Mounting on a mounting stand with the SSH/IQ sun shield
Materials and tools  SSH/IQ sun shield (see chapter 11 ACCESSORIES AND OPTIONS).
required
 4 mm set screw wrench
 Phillips screwdriver.
ba76188d01 03/2017 29
Mounting the sun

shield on a 1
mounting stand
2
3
4
Fig. 3-5 Mounting the SSH/IQ sun shield on a mounting stand
1 Screw the sun shield (pos. 1 in Fig. 3-5) with the four hexsocket head
screws (pos. 2), the washers (pos. 3) and the clamps (pos. 4) at the
required height on the mounting stand from the back.
Premounting the 7
ISO blind nuts
6
Fig. 3-6 Mounting the sun shield: Premounting the ISO blind nuts
2 Remove the two countersunk screws (pos. 5 in Fig. 3-6) and swing open
the lid.
3 Insert the cheese-head screws (pos. 6 in Fig. 3-6) with the plastic wash-
ers in the drilled mounting holes and loosely screw in the ISO blind nuts
(pos. 7).
30 ba76188d01 03/2017
Mounting the DIQ/

S 28X on the sun
shield
Fig. 3-7 Mounting the DIQ/S 28X on the sun shield SSH/IQ
4 Position the universal transmitter on the sun shield and fix it into place
with the two screws (pos. 6 in Fig. 3-6).
5 Close the lid and fix it with the two countersunk screws (pos. 5 in Fig. 3-
6).
3.7.3 Mounting under the SD/K 170 sun shield
The SD/K 170 sun shield can be mounted directly on a wall, on a mounting stand
or on a railing. The MR/SD 170 mounting kit is also required for mounting on a
mounting stand or railing.
How to mount the sun shield at the installation location is described

in the instructions for the sun shield or mounting kit.
Materials required  SD/K 170 sun shield (see chapter 11 ACCESSORIES AND OPTIONS)
 The MR/SD 170 mounting kit is also required for mounting the sun shield on
a mounting stand or railing (see chapter 11 ACCESSORIES AND OPTIONS).
ba76188d01 03/2017 31
Tools  Phillips screwdriver.
Mounting the DIQ/

S 28X with sun
shield
2
Fig. 3-8 Mounting the DIQ/S 28X with sun shield SD/K 170
1 Remove the two countersunk screws (pos. 1 in Fig. 3-8) and swing open
the module lid.
2 Position the universal transmitter on the sun shield and fix it into place
with the two screws (pos. 2 in Fig. 3-8).
3 Close the lid and fix it with the two countersunk screws (pos. 1 in Fig. 3-
8).
3.7.4 Top hat rail mounting
Materials required  THS/IQ kit for top hat rail mounting (see chapter 11 ACCESSORIES AND
OPTIONS).
Tools  Phillips screwdriver.
32 ba76188d01 03/2017
Mounting the DIQ/

S 28X on a top hat
rail
Fig. 3-9 Mounting the DIQ/S 28X on a top hat rail
1 Screw the clamping assembly (pos. 1 in Fig. 3-9) on the back of the uni-
versal transmitter with the two plastic tapping screws (pos. 2).
2 Attach the universal transmitter to the top hat rail from above using the
clamping assembly and press against the rail until the clamping assem-
bly clicks into place. The universal transmitter can be moved sideways
afterwards.
3 To unhook the universal transmitter, press it downward and pull it for-
ward at the bottom.
3.7.5 Panel mounting
Variants of the DIQ/S 28X without fieldbus or Ethernet interface can be mounted
to a switch panel with the PMS/IQ mounting set.
For variants of the DIQ/S 28X with fieldbus or Ethernet interface, we recom-
mend using the PMS/IQ-X mounting set. It enables to mount the DIQ/S 28X in
the switch panel so that the fieldbus or Ethernet interface is accessible behind
the switch panel.
ba76188d01 03/2017 33
Switch panel Variant Switch panel Switch panel Max. thickness

mounting sets DIQ/S 28X mounting set aperture of the switch
panel
DIQ/S 28X[CRx] PMS/IQ 138 x 138 mm 10 mm
DIQ/S 28X-PR, -MOD PMS/IQ-X 186 x 186 mm 8 mm
DIQ/S 28X[-CRx]-E(F) PMS/IQ-X 186 x 186 mm 5 mm
Switch panel Details on panel mounting with the PMS/IQ-X mounting set are given in the
mounting with operating manual of the PMS/IQ-X.
PMS/IQ-X
Switch panel Panel mounting with the PMS/IQ mounting set is described below:
mounting with
PMS/IQ
Materials required  PMS/IQ kit for panel mounting (see chapter 11 ACCESSORIES AND OPTIONS).
Tools  3 mm set screw wrench (contained in the panel installation kit).
Switch panel
aperture 138
138 Maximum thickness

10 mm
Fig. 3-10 Mounting aperture in the switch panel (dimensions in mm)
34 ba76188d01 03/2017
Mounting the DIQ/

S 28X in a switch
panel
3
e A räg
tag ktt
on onta
elm d K n
leb
ufk er
er
el
2
tap un re lab
i S n tie ve r
Be erne mon o
en
tf rem rrie
ng ca
nti ct
m ou onta
k ll c
tac ta
r s ins
Fo and
5
1
3
2
Fig. 3-11 Mounting the DIQ/S 28X in Fig. 3-11
1 Angle bracket
2 Bolts
3 Bolts
4 Impact protection plate
5 Bolts to fix the impact protection plate
1 Insert the universal transmitter in the panel aperture from the front.
2 Slightly unscrew the bolts (pos. 2 and 3) of the two angle brackets (pos.
1 in Fig. 3-11), but do not remove them.
3 Push in the two angle brackets - as shown in Fig. 3-11 - into the lateral
guides of the universal transmitter up to the stop.
4 Tighten the bolts (pos. 2).
5 Screw in the bolts (pos. 3) until the bolts rest snugly against the panel.
ba76188d01 03/2017 35
6 Fix the impact protection plate (Pos. 4) to the back of the DIQ/S 28X
with the bolts (Pos. 5).
3.8 Electrical connections: General instructions

Cable glands All electric cables are fed from below through openings prepared in the enclo-
sure of the DIQ/S 28X and the DIQ modules. Cable glands with different clamp-
ing ranges are included with the DIQ/S 28X to provide sealing between the
cable and enclosure as well as for strain relief. Select the suitable cable gland
for the relevant cable type and cable diameter:
 Small, clamping range 4.5 to 10 mm.
This cable gland is suitable for all cables (earth cable after stripping the outer
insulation, see section 3.7) and sensor connection cables.
sealing ring 20 x 15 x 1 mm
cable gland M16
blind plug
 Large, clamping range 7 to 13 mm.

This cable gland is required for cable sheaths with an outside diameter of
more than 10 mm and is screwed into the enclosure via an extension piece.
extension piece M16/M20
cable gland M20
If necessary, you can order more big cable glands (see

chapter 11 ACCESSORIES AND OPTIONS).
36 ba76188d01 03/2017
General instal- Observe the following points when attaching connecting wires to the terminal
lation instructions strip
 Shorten all wires to be used to the length required for the installation
 Always fit all the ends of the wires with wire end sleeves before connecting
them to the terminal strip
 Any wires that are not used and project into the enclosure must be cut off as
closely as possible to the cable gland.
 Screw a small cable gland with sealing ring into each remaining free opening
and close it with a blind plug.
WARNING
No free wires are allowed to project into the housing. Oth-
erwise, there is a danger that areas safe to contact could
come into contact with dangerous voltages. Always cut
off any wires that are not in use as closely as possible to
the cable gland.
3.9 Connecting the voltage supply

The two following paragraphs describe how to connect both models of the DIQ/
S 28X universal transmitter to the voltage supply.
ba76188d01 03/2017 37
3.9.1 DIQ/S 28X (line power version)
WARNING
If the power supply is connected incorrectly, it may repre-
sent a danger to life from electric shock. Pay attention to
the following points during installation:
 The DIQ/S 28X universal transmitter may only be con-
nected by a trained electrician.
 The connection of the DIQ/S 28X universal transmitter
to the power supply may only be carried out when it is
not carrying any voltage.
 The power supply must fulfill the specifications given
on the nameplate and in chapter 10 TECHNICAL DATA.
 When installed in a building, a switch or power switch
must be provided as an interrupt facility for the DIQ/
S 28X.
The interrupt facility must
– be installed in the vicinity of the DIQ/S 28X universal
transmitter, easily accessible by the user, and
– be labeled as the interrupt facility for the DIQ/S 28X
universal transmitter.
 After the DIQ/S 28X universal transmitter has been in-
stalled, it may only be opened if the line voltage has
been switched off beforehand.
Materials required  Wire end sleeves, suitable for the power line, with suitable crimping tool
 1 x cable gland with sealing ring (included in scope of delivery of the DIQ/
S 28X).
Tools  Cable stripping knife

 Wire stripper
 Phillips screwdriver
Preparing the
1 Cut off the cable to the required length.
power cable
2 Strip the cable insulation for approx. 45 mm.
3 Bare the wires of phases L and N and fit them with wire end sleeves.
4 If present, cut off the ground wire at the end of the cable sheath.
38 ba76188d01 03/2017
approx. 45 mm
cut ground wire here

Fig. 3-12 Prepared power cable.
NOTE
The ground wire must not project into the enclosure. Otherwise, malfunctions
could occur.
Connecting the
power line
2
1
3 N
L
Fig. 3-13 Inserting the supply line.
6 Screw a cable gland (pos. 1 in Fig. 3-13) with sealing ring (pos. 2) into
the enclosure below the power supply connection.
7 Loosen the coupling ring (pos. 3).
ba76188d01 03/2017 39
8 Feed the power line through the cable gland into the enclosure. When
doing so bend the flexible divider (pos. 4) to the right.
X19 X18
L1 N
100...
240V AC
MAINS
L N
Fig. 3-14 Line power connection.

section 3.13.
9 Connect phases L and N to the terminal strip. Make sure that the cable
assignment agrees with the specification on the terminal label under the
terminal strip.
WARNING
the cable gland.
11 Close the enclosure of the DIQ/S 28X.
40 ba76188d01 03/2017
3.9.2 DIQ/S 28X[-XX]/24V (24 V version)
WARNING
If the 24 V AC/DC supply is connected incorrectly, it may
represent a danger to life from electric shock. Pay atten-
tion to the following points during installation:
 The DIQ/S 28X universal transmitter may only be con-
nected by a trained electrician.
 The 24 V AC/DC supply must meet the specifications
quoted on the name plate and in chapter 10 TECHNICAL
DATA (protective low voltage SELV).
 The connection of the DIQ/S 28X universal transmitter
to the power supply may only be carried out when it is
not carrying any voltage.
 When installed in a building, a switch or power switch
must be provided as an interrupt facility for the univer-
sal transmitter DIQ/S 28X.
The interrupt facility must
– be installed in the vicinity of the DIQ/S 28X universal
transmitter, easily accessible by the user, and
– be labeled as the interrupt facility for the DIQ/S 28X uni-
versal transmitter.
Rechargeable battery systems should have a deep discharge

protection. The DIQ/S 28X[-XX]/24V does not have any built-in
deep discharge protection.
Materials required  Wire end sleeves, suitable for the 24 V AC/DC feed line, with suitable crimp-
ing tool
 1 x cable gland with sealing ring (included in scope of delivery of the DIQ/
S 28X).

 Wire stripper
Preparing the 24 V
1 Cut off the cable to the required length.
AC/DC line
2 Strip the cable insulation for approx. 45 mm.
3 Bare the wires 1 and 2 and fit them with wire end sleeves.
ba76188d01 03/2017 41
ca. 45 mm
wire 1
wire 2
Fig. 3-15 Prepared 24 V AC/DC line.
Connecting the
24 V AC/DC line
2
1
3 N
L
Fig. 3-16 Inserting the 24V AC/DC line
5 Screw a cable gland (pos. 1 in Fig. 3-16) with sealing ring (pos. 2) into
the enclosure below the 24 V AC/DC connection.
7 Feed the 24 V AC/DC line through the cable gland into the enclosure.
When doing so bend the flexible divider (pos. 4) to the right.
42 ba76188d01 03/2017
X19 X18
24V AC DC
INPUT
POWER
L N
Fig. 3-17 24 V AC/DC connection.

section 3.13.
8 Connect wires 1 and 2 to the terminal strip. Make sure that the cable
assignment agrees with the specification on the terminal label under the
terminal strip.
NOTE
No free wires are allowed to project into the housing. Otherwise there is the dan-
ger of short circuits that can cause a fire. Always cut off any wires that are not in
use as closely as possible to the cable gland.
ba76188d01 03/2017 43
3.10 Connections to the relay and current outputs
3.10.1 General installation instructions
WARNING
If external electrical circuits that are subject to the danger
of physical contact are incorrectly connected to the relay
contacts, there may be a danger of life threatening electric
shock. Electrical circuits are regarded to be subject to the
danger of physical contact when there are voltages higher
than the Safety Extra Low Voltage (SELV).
Pay attention to the following points during installation:
 Electrical circuits subject to the danger of physical
contact may only be connected by a qualified electri-
cian.
 Electrical circuits subject to the danger of physical
contact may only be connected when they are voltage-
free.
 If electrical circuits subject to the danger of physical
contact are switched with a relay, no circuit that is not
subject to this danger (e. g. the DIQ/CHV module) may
be operated on the further relays.
 Switching voltages and switching currents on the relay
contacts must not exceed the values specified in
chapter 10 TECHNICAL DATA. Protect electrical circuits
against currents that are too high with an electrical
fuse.
 Only single-phase consumers can be switched with the
relays. Under no circumstances may multiphase con-
sumers be switched with the aid of several relays (ex-
ample: three-phase current driven pumps). Always
switch multiphase consumers via a protective relay.
 After the Universal Transmitter DIQ/S 28X has been in-
stalled, it may only be opened if all external voltages
have been switched off beforehand.
Materials required  Wire end sleeves, suitable for the connecting wires, with suitable crimping
tool
 4 x cable gland with sealing ring (scope of delivery of the DIQ/S 28X)

 Wire stripper
 Small screwdriver
44 ba76188d01 03/2017
Connecting lines
to the terminal
strip
2
1
3 N
L
Fig. 3-18 Inserting lines

section 3.13.
2 Screw a cable gland (pos. 1 in Fig. 3-18) with the sealing ring (pos. 2)
into the enclosure below the respective connections.
4 Feed the line through the cable gland in the enclosure.
5 Connect the wires to the terminal strip. While doing so, pay attention to
the specifications on the label located under the terminal strip.
6 Tighten the coupling ring (pos. 3).
ba76188d01 03/2017 45
WARNING
come into contact with dangerous voltages. This could re-
sult in life threatening electric shock when working with
the universal transmitter DIQ/S 28X. Always cut off any
wires that are not in use as closely as possible to the cable
gland.
3.10.2 Usage of the auxiliary voltage
The universal transmitter DIQ/S 28X has a 24 V output (designation HILFSS-

PANNUNG or AUXILIARY VOLTAGE on the terminal strip). You can use this
auxiliary voltage for the relay-controlled opening of the valve in a DIQ/CHV valve
module for the compressed air-driven sensor cleaning function. To do so, you
have to connect the auxiliary voltage output, a free relay contact and the valve
connection in the DIQ/CHV in series. Bridge a terminal of the auxiliary voltage
output with a terminal of a relay output and run a control line from the remaining
terminals to the valve module.
NOTE
The auxiliary voltage must not be used for other purposes.
Connection Klemmleiste R3 R2 R1
scheme for one DIQ/S 182 AUXILIARY

VOLTAGE
sensor with X15 X14 X13 X12 X11 X10 X9 X8
compressed air
cleaning
Ventil-
Steuerleitung
Klemmleiste
DIQ/CHV X6 X5 X4 X3 X2 X1
DISTRUBUTION VALVE
NOTE
Run the bridge below the divider so the bridge does not bump against the circuit
board in the lid when the enclosure is closed.
46 ba76188d01 03/2017
Separating plate
Relais contact Auxiliary voltage output
Bridge
Valve control line
3.11 Commissioning
Start checklist and Before starting the system, carry out the system check using the following
system start checklist. Always carry out the check:
 before the initial commissioning
 before any further commissioning if the system has been previously extended
or modified.
Start checklist:
1 Are all components correctly connected with each other (see
section 3.6, if necessary, section 3.7)?
2 Is the universal transmitter correctly connected to the power
supply (see section 3.9)?
3 Do the line voltage and line frequency agree with the data on
the name plate of the universal transmitter?
4 Is the sensor ready for measuring, e.g. a D.O. sensor filled
with electrolyte solution?
Starting the Switch on the power supply of the DIQ/S 28X. As soon as the system is suc-
system cessfully initialized, the measured value display appears. With a sensor not yet
providing any measurement values, "Init" appears temporarily:
Select your system language during the first system start. The
selected system language can be changed in the Einstellungen/
Settings menu at any time.
ba76188d01 03/2017 47
Initial start phase The Universal Transmitter is initialized during the first start phase. All
IQ SENSORNET components are automatically registered with the Universal
Transmitter DIQ/S 28X. The system then performs a self test. This process can
take several seconds. During this period, the following display appears:
Fig. 3-19 Display during the initialization process
Second start As soon as the Universal Transmitter is successfully initialized, the measured
phase value display appears (fourfold display). In the case of IQ sensors that are not
yet providing measured values, "Init" appears temporarily
Fig. 3-20 Display after initialization of the terminal
Assign a name to each IQ sensor after putting it into operation for

the first time so you can identify it more easily. How to assign a
sensor name is described in section 5.4.1 on page 5-87.
If the system start failed, see chapter 9 WHAT TO DO IF ....
48 ba76188d01 03/2017
3.12 Installation examples
3.12.1 Connecting two sensors without compressed air cleaning
Maximum total cable length

M C S DIQ/S 28x(/24V) SNCIQ(/UG) plus SACIQ = 250 m
DIQ/S 284 ESC OK
UNIVERSAL TRANSMITTER
USB
DIQ/S 28x(/24V)
SNCIQ(/UG) SNCIQ(/UG)
DIQ/JB
1 2 3 4 5 6 7
1 2 3 4 5 6 7
SACIQ SACIQ
SACIQ SACIQ
Sensor 2 Sensor 1
Sensor 2 Sensor 1
Shield / Filler stranded wire

Connection
scheme of the DIQ/
JB Terminal strip SNCIQ(/UG)
DIQ/JB red green
X1 X2 X3 X4 X5 X6 X7
red green
red green
SACIQ SACIQ
black black
Sensor 2 Sensor 1
ba76188d01 03/2017 49
3.12.2 Connecting two sensors with compressed air cleaning

DIQ/S 28x(/24V)
SNCIQ(/UG) plus SACIQ = 250 m M C S
OK
ESC
SNCIQ(/UG)
Valve control line 1
Valve control line 2
DIQ/CHV 2 DIQ/JB DIQ/CHV 1
SACIQ SACIQ
Air Air
Sensor 2 Sensor 1
Connection Example:
scheme of valve Relay 1 controls the cleaning of sensor 1.
control Relay 2 controls the cleaning of sensor 2.
Variant: Relay 1 controls the cleaning of both sensors. Cleaning of both sensors
is carried out with the same settings.
NOTE
In this configuration, the free switching contact (here: R3) may be used to switch
SELV voltages only.

the cable gland.
50 ba76188d01 03/2017
Variante
Klemmleiste R3 R2 R1 AUXILIARY
VOLTAGE R3 R2 R1 AUXILIARY
VOLTAGE
DIQ/S 28X
X17 X16 X15 X14 X13 X12 X11 X10 X17 X16 X15 X14 X13 X12 X11 X10
a b c
a b c
Ventil-
Steuerleitung 1
Klemmleiste
DIQ/CHV 1 X6 X5 X4 X3 X2 X1
DISTRUBUTION VALVE
Ventil-
Steuerleitung 2
Klemmleiste
X6 X5 X4 X3
DIQ/CHV 2 X2 X1
DISTRUBUTION
VALVE
Connection Shield / Filler stranded wire

scheme of the DIQ/
JB Terminal strip SNCIQ(/UG)
DIQ/JB red green
X1 X2 X3 X4 X5 X6 X7
red green
red green
SACIQ SACIQ
black black
Sensor 2 Sensor 1
ba76188d01 03/2017 51
3.12.3 Connection of a sensor that is located at a distance

(without compressed air cleaning)
DIQ/S 28x(/24V)
M C S
DIQ/S 284
UNIVERSAL TRANSMITTER ESC OK

USB
SNCIQ(/UG) plus SACIQ = 250 m
SNCIQ(/UG)
DIQ/S 28x
DIQ/JB
SNCIQ(/UG)
1 2 3 4 5 6 7
SACIQ
1 2 3 4 5 6 7
SACIQ
Sensor
Shield / Filler stranded wire

Connection
scheme of the DIQ/
JB SNCIQ(/UG)
red green
Terminal strip
DIQ/JB X1 X2 X3 X4 X5 X6 X7
red green
SACIQ
black
52 ba76188d01 03/2017
3.13 Figures of the terminal strips
DIQ/S 28X X19 X18 X17 X16 X15 X14 X13 X12
≤ 240V AC ≤ 240V AC ≤ 240V AC
X11 X10 X9
0/4...20mA
X8 X7
0/4...20mA
X6 X5
0/4...20mA
X4 X3 X2 X1
SHIELD
GREEN
RED
-CRx[-E] L1 N ≤ 2A AC ≤ 2A AC ≤ 2A AC AUXILIARY
VOLTAGE
100...
240V AC
+ REC - + REC - + REC -
MAINS R3 R2 R1 AUXILIARY C3 C2 C1 SENSORNET 1
DIQ/S 28X X19 X18 X17 X16 X15 X14 X13 X12 X11 X10 X9 X8 X7 X6 X5 X4 X3 X2 X1
-CRx[-E] ≤ 240V AC ≤ 240V AC ≤ 240V AC 0/4...20mA 0/4...20mA 0/4...20mA
SHIELD
GREEN
RED
≤ 2A AC ≤ 2A AC ≤ 2A AC AUXILIARY
/24V 24V AC DC
VOLTAGE
INPUT
+ REC - + REC - + REC -
POWER R3 R2 R1 AUXILIARY C3 C2 C1 SENSORNET 1
DIQ/S 28X X19 X18 X17 X16 X15 X14 X13 X12
≤ 240V AC ≤ 240V AC ≤ 240V AC
X11 X10 X6 X5 X4 X3 X2 X1
GREEN
SHIELD
-MOD, -PR, -EF
RED
GREEN
RED
SHIELD
L1 N ≤ 2A AC ≤ 2A AC ≤ 2A AC AUXILIARY
VOLTAGE
100...
240V AC
MAINS R3 R2 R1 AUXILIARY SENSORNET 2 SENSORNET 1
DIQ/S 28X X19 X18 X17 X16 X15 X14 X13 X12 X11 X10 X6 X5 X4 X3 X2 X1
-MOD, -PR, -EF ≤ 240V AC ≤ 240V AC ≤ 240V AC
SHIELD
GREEN
RED
SHIELD
RED
GREEN
≤ 2A AC ≤ 2A AC ≤ 2A AC AUXILIARY
/24V 24V AC DC
VOLTAGE
INPUT
POWER R3 R2 R1 AUXILIARY SENSORNET 2 SENSORNET 1
DIQ/CR3 X17 X16 X15 X14 X13 X12

£ 240V AC £ 240V AC £ 240V AC
X9
0/4...20mA
X8 X7 X6
0/4...20mA
X5 X4
0/4...20mA
X6 X5 X4 X3 X2 X1
GREEN
RED
SHIELD
GREEN
RED
SHIELD
(component of the
£ 2A AC £ 2A AC £ 2A AC
DIQ/S 284-CR6
+ REC - + REC - + REC -
[-XX]) R3 R2 R1 C3 C2 C1 SENSORNET 2 SENSORNET 1
1 2 3 4 5 6 7
DIQ/JB (7 passive, potential-free terminals
for line extension)
1 2 3 4 5 6 7
DIQ/CHV (AUXILIARY) VALVE
X6 X5 X4 X3 X2 X1
ba76188d01 03/2017 53
Operation DIQ/S 28X
4 Operation
4.1 Operating elements
4.1.1 Overview of the operating elements
The Universal Transmitter is equipped with a large display for the clear presen-
tation of current measured values, the graph of measured values, status
displays and message texts.
The 5 keys <M>, <C>, <S>, <ESC>, <OK> and the arrow keys <> are
used to operate the IQ SENSORNET system.
M C S
DIQ/S 284 ESC OK

USB
Fig. 4-1 Operating elements of the DIQ/S 28X
1 Display (see section 4.1.2 DISPLAY)

2 Keypad
Arrow keys and 5 keys <M>, <C>, <S>, <ESC>, <OK> (see
section 4.1.3 KEYS)
54 ba76188d01 03/2017
DIQ/S 28X Operation
4.1.2 Display
2 3 4 5 6
Fig. 4-2 Display
1 Name of the display indication (is skipped in the measured value

display)
2 Name and series number (e.g. S284-16160001) of the instrument
Under this name the DIQ/S 28X[-xx]-E(F) can be addressed in an
Ethernet network (see section 6)
3 Date, time
4 User right (details see below)
5 Error symbol h:
If the error symbol flashes, a new or unacknowledged error message
is present in the log book that requires immediate action (see
section 4.5.3).
6 Info symbol i:
If the info symbol flashes, new or unacknowledged information is
present in the log book (see section 4.5.3).
7 Display range for measured values, menus, lists, etc.
8 Help line with operating instructions
Detail on the user A Lock open: No access control, settings released

right (4) System settings can be changed
Crown: Administrator authorization
Configuration and running operation of the system
Tool: Maintenance authorization
Running operation of the system and maintenance activities
Eye: Monitoring permission
Only read permission, no operation of the system
ba76188d01 03/2017 55
Operation DIQ/S 28X
Measured value The measured value display contains the following information for each IQ sen-
display sor:
1 2 3 4 5
Fig. 4-3 Display - measured value display
1 Consecutive numbering of the measured values

2 Main measured value
3 Unit and parameter of the main measured value
4 Name of the sensor (to enter name: see section 5.4.1
5 User right (details see below)
6 Adjoining measured value with unit
Special displays Init Sensor is being initialized

 during commissioning or
 if a new IQ sensor is recognized that is not yet giving mea-
sured values
---- Invalid measured value
Cal Sensor is being calibrated
Clean Cleaning system active, sensor is offline
Error Sensor is inactive or defective
OFL Measuring range undercut or exceeded (overflow)
Display Sensor in maintenance condition
flashes
56 ba76188d01 03/2017
DIQ/S 28X Operation
4.1.3 Keys
Key Function
<M> Display measured values
<C> Start calibration
of the IQ sensor selected in the measured value display
<S> Open the Einstellungen/Settings menu
<ESC> Change to the higher menu levels or
abort entries without storing them
<OK> Confirm selection
<> Highlight and select:
 Menu items
(arrow keys)  Entries
 Columns or fields
 Letters or numerals
The selection highlighted with the arrow keys is displayed as white

text on a black background (reverse video).
4.2 General operating principles

The operation of the IQ SENSORNET is standardized and user-friendly.
 Select an item with the arrow keys <>
– Highlight individual elements in menus, lists and tables, e.g. menu
entries, list elements, columns or fields
– Select a setting in selection fields
– Select a character in text entry fields
 Confirm a selection with the <OK> key.

 Break off an action and change to the next higher level with the <ESC> key.
 Start a calibration procedure with the <C> key.
 Switch to the settings with the <S> key.
 Change to the measured value display and break off current actions with the
<M> key.
ba76188d01 03/2017 57
Operation DIQ/S 28X
Short operating instructions are given in the help lines on the dis-
play.
Examples of the operating principles are given below:

 Navigation in menus, lists and tables (see chapter 4.2.1)
 Entering text and numerical values (see chapter 4.2.2)
If two or more terminals are used in an IQ SENSORNET, access to the

functions <C> and <S> is blocked when the functions are already
being used on another terminal.
4.2.1 Navigating in menus, lists and tables
1 Open the Einstellungen/Settings menu with <S>.

Menus appear in the form of a list on the display, e.g. the Einstellungen/
Settings menu shown here.
Fig. 4-4 Einstellungen/Settings
2 Select a menu item (e.g. System settings) with <>.

Move the highlighting (reverse video display, black background) in the
list of menu items with the arrow keys <>.
3 Confirm the menu item (e.g. System settings) with <OK>.
The display (e.g. System settings) opens.
Confirm the selection and move to a new display by pressing the <OK>
key.
58 ba76188d01 03/2017
DIQ/S 28X Operation
4 Return to a higher level with <ESC>.

or:
Switch to the measured value display with <M>.
4.2.2 Entering texts or numerals
You can assign names to IQ sensors and MIQ output modules. Example: Enter-
ing a sensor name:

2 Select the Edit list of sensors menu item with <>.
3 Confirm the Edit list of sensors menu item with <OK>.
The Edit list of sensors display opens. A column is highlighted.
4 Select the Sensor name column with <>.
5 Confirm the Sensor name column with <OK>.
A sensor name is highlighted.
6 Select a sensor name with <>.
Fig. 4-5 Edit list of sensors
7 Confirm the selection with <OK>.

The name of the selected sensor is edited.
ba76188d01 03/2017 59
Operation DIQ/S 28X
The following letters, numerals and special characters can be

entered: AaBb..Zz0..9µ%&/()+-=><!?_ °.
8 Select a letter or numeral with <>.

9 Confirm the letter with <OK>.
The character p appears behind the last letter.
60 ba76188d01 03/2017
DIQ/S 28X Operation
10  Add a new character

Select the character to be added with <> and confirm with
<OK>.
or
 Delete the last character
Select the character with <> and confirm with <OK>.
or
 Adopt the name
Select the character with <> and confirm with <OK>.
11 Repeat steps 8 to 10 until the whole name has been entered.
You can break off entering the name with <ESC>. The old name is
retained.
4.3 Access to the IQ SENSORNET with active access control
Access control is switched off in the delivery condition. No login to

the IQ SENSORNET is required.
As soon as an access control of any type is enabled, access to the

IQ SENSORNET is protected completely or partly.
Access to the system is enabled as follows:
 Connecting the electronic key to the USB interface (Universal Transmitter),

if the administrator has enabled this function
 Entering a password
Extended access control:
In the Display/Options / Change user rights menu, enter the
password with the arrow keys and confirm with OK.
Extended access control with instrument block:

Press the any button.
In the password query, enter the password with the arrow keys
and confirm with OK.
ba76188d01 03/2017 61
Operation DIQ/S 28X
Further details on access control (see section 5.3)
4.4 Display of current measured values

Several options can be selected for displaying the measured values:
 Measured values (1 sensor)
The measured value is shown numerically and as a bar graph on the Mea-
sured values (1 sensor) display (see section 4.4.1)
 Measured values (4 sensors)
The Measured values (4 sensors) display provides an overview of a maxi-
mum of four IQ sensors (see section 4.4.2)
 Measured values (8 sensors)
The Measured values (8 sensors) display provides an overview of a maxi-
mum of eight IQ sensors (see section 4.4.3)
Switch between the different types of display as follows:
1 Call up the measured value display with <M>.

2 Open the Display/Options menu with <OK>.
Fig. 4-8 Display/Options
3 Select and confirm a display type with <> and <OK>.The

selected display is activated.
62 ba76188d01 03/2017
DIQ/S 28X Operation
4.4.1 Displaying a single measured value
The measured value is shown numerically and as a bar graph on the Measured
values (1 sensor) display.
Fig. 4-9 Values: location -> Measured values (1 sensor)
4.4.2 Displaying four measured values
Up to four measured values of IQ sensors are shown on the display at the same
time.
Fig. 4-10 Values: location -> Measured values (4 sensors)
4.4.3 Displaying eight measured values
Up to eight measured values of IQ sensors are shown on the display at the same
time.
ba76188d01 03/2017 63
Operation DIQ/S 28X
Fig. 4-11 Values: location -> Measured values (8 sensors)
4.4.4 Displaying recorded measured values
If the measured value recording has been activated for an IQ sensor (see
section 5.10), the temporal course of the recorded measured values can be
displayed numerically and graphically.
The following display options are possible:
 Monthly load of selected sensor (graphic display)
 Weekly load of selected sensor (graphic display)
 Daily load of selected sensor (graphic display)
 Measured value list of selected sensor (numerical display)
64 ba76188d01 03/2017
DIQ/S 28X Operation
X 3
4
5
1 Display
2 Range of the graphical display
The time range (x-axis) corresponds to the selected type of display
(1 day, 1 week, 1 month).
The value range of the y-axis is automatically adjusted to min and
max values
3 Position of the cursor (X)
4 Data on the position of the cursor (X)
(date, time, main and secondary measured value)
5 Navigation instructions
Fig. 4-12 Daily load of selected sensor (example)
Displaying
1 Switch to the measured value display with <M>.
recorded
measured values 2 Select an IQ sensor with <>.
4 Select one of the display types with <>
 Monthly load of selected sensor
 Weekly load of selected sensor
 Daily load of selected sensor
 Measured value list of selected sensor
and confirm with <OK>.
The selected option is displayed.
ba76188d01 03/2017 65
Operation DIQ/S 28X
Fig. 4-13 Monthly load of selected sensor (example)
5 Move the cursor (X) along the measured value curve with <>.
The cursor (X) marks the selected measured value.
6 Switch to the next display option with a shorter display period with
<OK>.
or
Switch to the next display option with a longer display period with
<ESC>.
4.4.5 Transmitting recorded measurement data to a PC
Recorded measured values can be transmitted to a PC via the Ethernet inter-

face. For details on data transmission, see section 6.
4.5 Messages and log book

The IQ SENSORNET continuously monitors the status of the entire system. If the
IQ SENSORNET identifies system changes, a message appears. New messages
can be recognized by the flashing information symbol or error symbol on the
display.
All messages are recorded in the log book.
4.5.1 Message types
The system differentiates two types of messages:

 Error h
Indicates a critical status in the system or an individual system component
that requires immediate action.
66 ba76188d01 03/2017
DIQ/S 28X Operation
In the case of new error messages, the error symbol flashes on the display.
 Information i
Information that does not require immediate action.
In the case of new information, the info symbol flashes on the display.
In the case of errors, immediately open the detailed message text

in the log book and perform the recommended actions. If the
actions have been performed, mark the message as read (see
section 4.5.3).
4.5.2 Log book
The log book is a list with all the messages from all modules. The log book
contains up to 1000 entries. If there are more than 1000 messages, the oldest
entries are deleted.
New messages can be recognized by the flashing information symbol or error
symbol. The log book always contains the latest message in the first position.
They do not yet have a checkmark in the status field.
The flashing of the info or error symbol only stops after all detailed message
texts in the log book have been opened and marked with a checkmark () (see
section 4.5.3).
ba76188d01 03/2017 67
Operation DIQ/S 28X
Structure of the log

book
1 2 3 4 5
Fig. 4-14 Log book of entire system
1 Message category (error or info symbol)

2 Module that triggered the message.
SYS System (Universal Transmitter, controller)
S01 IQ sensor (number 01)
S?? IQ sensor (inactive, dataset erased)
D01 DIQ output module (number 01)
D?? DIQ output module (inactive, dataset erased)
3 Message code
4 Date and time of the message
5 Status field of the message
 Message was acknowledged
No checkmark Message was not acknowledged
The system provides the following log books:

 Log book of entire system:
List of all messages from all modules
 Log book of selected sensor:
List of all messages from a single IQ sensor.
There is a detailed message text for each message of a module that is ready for
operation. The detailed message text on each message is given in the log book
(see section 4.5.3) and in the operating manual of the registering module.
Structure of the The message code consists of 6 characters and can contain numerals and let-
message code ters, e.g.: II21171.
68 ba76188d01 03/2017
DIQ/S 28X Operation
Type number
Type
Component code
Category
II2 171
Posi- Information Explanation

tion
1-3 Short message The short form of the message con-
form tains the following information of the
message:
Category, type and type number
1:  Info message (I)
possible catego-  Error message (E)
ries
2:  Calibration data (C)
possible types  Installation and commissioning (I)
 Instructions for service and repair
(S)
 Application instructions (A)
3: Type number Each type contains subtypes (0..9A..Z)
4-6 Module code The three-digit module code desig-
nates the module that generated the
message. The module code can be
found in the chapter LISTS of the
respective component operating man-
ual.
Example: The "171" module (Universal Transmitter DIQ/S 284) sends a message with the
Message code short message form "II2".
II2171 This is an info message (I) of the type Installation (I) with the type number (2).
The detailed message text of the short form message (II2) can be found in the
log book and in the operating manual of the component that sent it.
ba76188d01 03/2017 69
Operation DIQ/S 28X
The detailed message text in the log book contains a precise

description of the message code and, if required, any further
actions.
The detailed message texts can also be found in the component

operating manuals of the individual components.
The log book shows the current status at the point of time it was
opened. If new messages arrive while a log book is open, these
do not appear in the log book. As usual, you are informed of new
messages by flashing info or error symbols. The current log book
with the new messages can be viewed by closing and reopening
the log book.
4.5.3 Viewing detailed message texts

3 Using <> and <OK>, select and open the 310 - Log book of
entire system.
A list of log book entries appears.
4 Using <> and <OK> select and confirm a new log book entry
(unchecked).
The message text with further information on the selected log book
entry appears.
Fig. 4-15 Log book of entire system
70 ba76188d01 03/2017
DIQ/S 28X Operation
5 Acknowledge the message with <OK>. A checkmark appears in the log

book entry.
6 Exit the message text with <ESC>.
Acknowledgment of a new message text in the log book marks the

message as read. When all errors or information messages are
acknowledged, the symbols no longer flash.
With the Acknowledge all messages function you can acknowledge all
messages at the same time (see section 4.5.4).
Message texts are stored in the modules that caused them. There-
fore, further information on a log book entry for an IQ sensor such
as, e.g. calibration messages, instructions and help texts are only
accessible in the case of connected components that are ready for
operation.
If a message text is not available because, e.g. a module is not connected with
the system, you can look up the detailed text of the message as follows:
 Messages of the system are given in this operating manual (see

section 12.1).
 Messages of a module are given in the respective component operating man-
ual of the module.
4.5.4 Acknowledge all messages

3 Using <>, select the menu item, Service and confirm with
<OK>.
4 Using <>, select the menu item, Acknowledge all messages
and confirm with <OK>. A security prompt opens.
5 Using <>, select Acknowledge and confirm with <OK>. All mes-
sages are acknowledged. Error symbol and info symbol do no longer
flash.
ba76188d01 03/2017 71
Operation DIQ/S 28X
4.6 Calibration data
Details on calibration are given in the operating manual for the

IQ sensor.
Each calibration of IQ sensors that are able to be calibrated causes an entry to

be made in the log book. Log book entries contain the following information:
 Calibration date
 Calibration successful or not successful.
The detailed calibration data of the last calibrations are integrated in the Calibra-
tion history of selected sensor overview.
All calibration data are stored in the IQ sensor. In order to view the
calibration data of an IQ sensor, the IQ sensor must be connected
to the IQ SENSORNET and must be ready for operation.
4.6.1 Calibration entries in the log book
The date and time of a calibration are entered in the log book. The respective
message text contains an indication as to whether a calibration was successful
or not. The values determined with calibration can be viewed in the calibration
history (see section 4.6.2).

2 Using <>, highlight a sensor and confirm with <OK>.
The Display/Options menu opens.
3 Using <>, highlight the menu item, Log book of selected sen-
sor, and confirm with <OK>. Calibration entries in the log book are held
in message code (ICxxxx and ECxxxx).
4 Select and open a calibration entry (ECxxxx or ICxxxx) with <>
and <OK>.
5 Exit the Calibration history of selected sensor with <>.
4.6.2 Calibration history
The calibration history contains the detailed calibration data of the last calibra-
tions.
72 ba76188d01 03/2017
DIQ/S 28X Operation

2 Using <>, highlight a sensor and confirm with <OK>.
The Display/Options menu opens.
3 Using <>, highlight the menu item, Calibration history of
selected sensor, and confirm with <OK>.
The calibration history with the results of the last calibration procedures
opens.
4 Exit the Calibration history of selected sensor overview with <M>.
4.7 Status info of sensors and outputs

The display of the instrument status provides a simple overview of the current
modes of sensors (sensor info) and outputs in the IQ SENSORNET.
The status display can be reached in the Einstellungen/Settings/Service/List of
all components menu (see section 4.10).
1 Call up the List of all components (see section 4.10).

2 Highlight the required component with <> and confirm with
<OK>.
 Output module: The Status of output channels window opens up (for
details, refer to the operating manual of the output module).
 Sensor: The sensor info opens up (for details, refer to the operating
manual of the selected sensor).
Fig. 4-16 List of all components with sensor info
3 Exit the Status of output channels window with <M> or <ESC>.
ba76188d01 03/2017 73
Operation DIQ/S 28X
4.8 General course when calibrating, cleaning, servicing or

repairing an IQ sensor
When an IQ sensor is calibrated, cleaned, serviced or repaired, the mainte-
nance condition for the relevant IQ sensor should always be switched on.
In the maintenance condition
 the system does not react to the current measured value or the condition of
the selected IQ sensor
 linked outputs are frozen
 IQ sensor errors do not prompt changes in the conditions of linked outputs.
The maintenance condition for IQ sensors is automatically activated

 during calibration. After calibration the IQ sensor remains in the maintenance
condition until the maintenance condition is switched off manually (see
section 4.8.3)
 during a compressed air cleaning cycle.
Therefore, keep to the following course when you calibrate, clean, service or
repair an IQ sensor.
Outlet
1 Switch on the maintenance condition for the IQ sensor (see
section 4.8.2).
The display of the sensor in the measured value display flashes.
2 Pull the sensor out of the sample.
3 Perform the calibration in the laboratory, cleaning, maintenance or
repair (removing and replacing) of the sensor (about these topics, see
the component operating manual of the corresponding sensor).
4 Submerse the sensor in the sample again.
5 Wait until the measured value no longer changes.
6 Switch off the maintenance condition for the sensor (see section 4.8.3).
The display of the sensor in the measured value display no longer
flashes.
4.8.1 Maintenance condition of IQ sensors
The following diagram gives you an overview of when an IQ sensor is in the

maintenance condition.
74 ba76188d01 03/2017
DIQ/S 28X Operation
Maintenance
Sensor
condition
cleaning
Measured value Measured value display ON manual Measured value
active
display display
The measured value
Clean flashes stops flashing. The measured value
Maintenance
Sensor flashes.
condition
cleaning
OFF c e/m OFF manual
(automatic sequence)
c
Display mesage
Switch on the
maintenace
condition
Continue / Cancel
Calibration
Step 1
m
g e
Calibration
Step n
end g/m/e
= Maintenance condition ON = Maintenance condition OFF
4.8.2 Switching on the maintenance condition
Switch on the maintenance condition manually when you want to clean, service
or repair (remove and replace) an IQ sensor.
1 Press <M> to call up the measured value display.

2 Select the sensor you want to switch on the maintenance condition for
with <>.
The display of the sensor in the measured value display does not flash.
ba76188d01 03/2017 75
Operation DIQ/S 28X
4 Using <>, highlight the menu item, Switch maintenance condi-

tion on/off, and confirm with <OK>.
A window that informs you about the maintenance condition opens up.
5 Use <OK> to confirm Continue.
The selected sensor is in the maintenance condition. Linked outputs are
frozen.
Subsequently, perform the cleaning, maintenance or repair work (removal and

replacement).
When you have finished calibrating, cleaning, servicing or repairing the sensor,
switch off the maintenance condition manually (see section 4.8.3).
4.8.3 Switching off the maintenance condition

2 Select the sensor you want to switch off the maintenance condition for
with <>.
4 Using <>, highlight the menu item, Switch maintenance condi-
tion on/off, and confirm with <OK>.
A window that informs you about the maintenance condition opens up.
5 Use <OK> to confirm Continue.
The maintenance condition of the selected sensor is switched off.
Linked outputs are released.
The display of the sensor in the measured value display does not flash.
If a power failure occurs, the outputs automatically are in the non-

operative condition (relays: open, current output: 0 A; see compo-
nent operating manual of the output module). After the end of the
power failure the outputs work as defined by the user again.
If a power failure occurs while an IQ sensor that is linked with an out-

put is in the maintenance condition, the current and relay outputs
work as defined by the user after the maintenance condition has
been switched off only (see section 4.8.3).
76 ba76188d01 03/2017
DIQ/S 28X Operation
4.9 USB interface

The USB interface on the DIQ/S 28X can be used for the following actions:
 Saving data of the IQ SENSORNET to a USB memory device
(see section 4.9.1)
 Transmitting configuration data to the Universal Transmitter
(see section 4.9.2)
 Carrying out a software update
(see section 4.11)
 Accessing the system with the Electronic Key
(see section 4.3)
4.9.1 Saving IQ SENSORNET data to a USB memory device
You can save the following data types:

 Configuration data (see section 4.9.2)
 Measurement data (see section 4.9.2)
 Log book
 Calibration history
The configuration data can be transferred from the USB memory device back to
the IQ SENSORNET. Thus, you can very easily create systems that are config-
ured identically.
Data backup
3 Use <> and <OK> to open the Data transfer to USB memory
menu.
4 Select the data to be saved with <>.
 Save configuration
 Measured data storage
 Log book
 Calibration history
5 The data are prepared for the transfer.
ba76188d01 03/2017 77
Operation DIQ/S 28X
You can cancel the data saving process by highlighting and confirm-
ing the Cancel menu item with <> and <OK>. In this case
the data will not be stored to the USB memory device.
6 Press <> to highlight the Save menu item and confirm with
<OK>.
The selected data will be stored to the USB memory device.
4.9.2 Restore system configuration
The restoration of a configuration back to the universal transmitter is carried out

manually from the USB memory. For this it is useful to save the configuration to
a USB memory device manually and regularly.
Manual restoration To transfer configuration data to the Universal Transmitter, proceed as follows:
1 Open the Settings menu with <S>.

2 Press <> to select the menu item Data transfer to USB memory
and press <OK>.
3 Press <> to select the menu item Retransfer configuration and
press <OK>. The process is started.
4 Wait until the restore is terminated.
5 Confirm the concluding message with <OK>.
4.10 Info on software versions

The system informs you of the current versions of the software of the individual
IQ SENSORNET components.

3 Using <>, highlight the menu item, Service, and confirm with
<OK>. The Service dialog window opens.
4 Using <>, highlight the menu item, List of all components, and
confirm with <OK>.
The List of all components dialog box opens.
78 ba76188d01 03/2017
DIQ/S 28X Operation
Fig. 4-17 List of all components
5 Exit the List of all components dialog box with <M> or <ESC>.
If the software version of a component is not up-to-date, you can

carry out a software update via the USB interface (see section 4.11).
4.11 Software-Update for DIQ/S 28X

With a Software-Update, you maintain the latest state of the instrument software
for the Universal Transmitter DIQ/S 28X and all active components.
The update packet with the current instrument software for active
IQ SENSORNET components and detailed instructions on how to proceed are
available on the Internet under www.YSI.com.
The instrument software is transferred to the System 28X via the USB port and
with the aid of a USB memory device.
A Software-Update does not change the measurement settings,

measurement data and calibration data.
You can view the software versions of all components in the dialog
box, List of all components (see section 4.11).
ba76188d01 03/2017 79
Settings/setup DIQ/S 28X
5 Settings/setup
5.1 Selecting the language
A list shows all the available system languages.

2 Using <> and <OK>, select and confirm the menu item, Lan-
guage.
The Language display opens.
Fig. 5-1 Language
3 Select a language from the list with <> and confirm with <OK>.
The active language is marked with a checkmark.
4 Switch to the higher menu level with <ESC>.
or:
Switch to the measured value display with <M>.
If the selected system language is not available in a component, all

indications of this component (e.g. sensor, Universal Transmitter,
output module) appear in the standard language, English. To acti-
vate the selected system language for this component, a software
update of the component is required (see section 4.11).
5.2 Terminal settings of the DIQ/S 28X

The terminal settings include:
 Terminal name
80 ba76188d01 03/2017
DIQ/S 28X Settings/setup
 Illumination brightness
 Illumination brightness (standby)
Fig. 5-2 Terminal settings
Setting Selection/Val- Explanation

ues
Terminal name AaBb..Zz User-defined character string with max. 15 char-
0..9µ%&/() acters
+-=><!?_ °
Illumination brightness AUTO Brightness of the display during operation of the
0 ... 100 % terminal
Illumination brightness AUTO Brightness of the display during operation if no

(standby) 0 ... 50 % key is pressed for a longer period of time
5.3 Access control

Use the Access control function to define the safety settings for the
IQ SENSORNET.
The DIQ/S 28X provides the following levels of system security:
 Access control
(4 authorization levels, see section 5.3.1):
– No access control
– Administrator authorization
– Maintenance authorization
– Read permission
ba76188d01 03/2017 81
 Access control with instrument block (see section 5.3.2):
Access to the system with active access control (see section 4.3).
Default settings Access control is switched off in the delivery condition.

Any user can carry out all functions.
Saving the If access control for the IQ SENSORNET is active and the administrator password
password is lost, rapid administrator access to the IQ SENSORNET is no longer possible.
To avoid losing the administrator password, we recommend saving it. This also
applies to the use of the electronic key.
To save the administrator password, you can save it on an electronic key, for
example, and/or note it down on paper or on a PC. Keep the passwords in a safe
place.
If the IQ SENSORNET is locked and the administrator password lost,

you can unlock the system with a master password. Please contact
the service department.
The master password is valid for 7 days.
If you have unlocked the IQ SENSORNET with the master password,
we recommend to note down the normal administrator password
and keep it in a safe place.
5.3.1 Activating the access control
Access control provides three preconfigured user rights in the system. Each
user type can be protected with its own password.
User right The current user right is shown on the display with the following symbols.
Validity User right Symbol User rights

System-wide Settings are A All functions in the system are accessible to
unlocked all users
(access control
swiched off)
82 ba76188d01 03/2017
Validity User right Symbol User rights

Administration  Access only with password
 Change system settings
 Assign user rights
 Calibration
 Data backup
 Restore configuration
 View measured values
 Carry out software updates
Maintenance  Access only with password
 Calibration
 Data backup
Viewer  Without instrument block:
Access without password
 With instrument block:
Access only with password
 Data backup
For the instru- Instrument  Instrument block switched off:
ment on which block User rights as for Viewer.
the function  Instrument block active:
was activated The System 28X is blocked. Only the
IQ SENSORNET logo is displayed. Access
only with password.
Switching on the
access control
2 Using <> and <OK>, select and confirm the menu item, Access
control.
The Simple access control dialog window opens.
3 Using <>, select the function, Activate extended access control
User right and instrument block can be selected.
ba76188d01 03/2017 83
Fig. 5-3 Settings -> Access control -> Extended access control
The instrument automatically generates a password for each user right. This
password can be accepted or changed.
4 Press <> to select an user right and confirm with <OK>.

If necessary, change the password in the selection dialog and/or save
the password to a connected USB memory.
5 Note passwords.
For reasons of safety the administrator password at least should be
saved in such a way that it can be accessed in an emergency.
6 Press <> to select the Apply settings function and confirm with
<OK>.
A security prompt opens.
7 Using <>, select OK and confirm with <OK>.
The settings are adopted.
The Extended access control window is still open.
The current passwords are visible.
The Viewer user right is active.
Switching off the

1 Press <OK> to open the Display/Options / Change user rights menu.
access control
The password query is displayed.
2 Enter and confirm the administrator password with <> and
<OK>.
Deactivate the access control.
Take over the setting.
84 ba76188d01 03/2017
5.3.2 Activating the instrument block
With the function Device lock you can protect the Universal Transmitter no only
against unauthorized operating bus also against unauthorized reading of the
current measured values. By activating the instrument block the password for
viewing the measured values is activated.
After a selected interval without user entries, the system is automatically
blocked. The display shows only the IQ SENSORNET logo.
Switching on the
1 Call up the access control (see section 5.3.1).
instrument block
2 Press <> to select the Device lock function and confirm with
<OK>.
A checkmark appears next to the function.
3 Press <> to select the Apply settings function and confirm with
<OK>.
A security prompt opens.
4 Using <>, select OK and confirm with <OK>.
The settings are adopted.
The Access control dialog window is still open.
The current passwords are visible.
Switching off the

1 Press <OK> to open the Display/Options / Change user rights menu.
instrument block
The password query is displayed.
2 Enter and confirm the administrator password with <> and
<OK>.
Deactivate the access control.
Take over the setting.
5.3.3 Electronic key
The administrator can simplify access to the IQ SENSORNET by saving the pass-
word to USB memory. The USB memory thereby becomes an electronic key.
When the electronic key is connected to the System 28X, the user right stored
there with the relevant password is automatically read out. The user of the elec-
tronic key is logged on to the system with his user right without any further pass-
word prompt.
When the electronic key is disconnected, the IQ SENSORNET automatically
switches to the lowest user right.
ba76188d01 03/2017 85
Passwords for different IQ SENSORNET systems can be saved to every elec-

tronic key.
For each IQ SENSORNET system only one password can be saved to each elec-
tronic key.
Saving a password
1 Connect the USB memory to the USB-A interface.
to an electronic
key 2 Open the Settings menu with <S>.
3 Using <> and <OK>, select and confirm the menu item, Access
control.
The Access control dialog window opens.
4 Press <> to select an authorization level and confirm with
<OK>.
5 Using <>, select the menu item, Save access code on USB
memory and confirm with <OK>.
The password for the system settings is saved to the USB memory.
5.3.4 Access to the IQ SENSOR NET with active access control
Simple access control
z  Administrator access after entering the password in order to take

over a changed setting:
The protection is automatically reactivated after the one setting was
changed.
 Administrator access through connecting the electronic key: The
protection is restored by disconnecting the electronic key
Access control (with instrument block):
 Administrator access through entering the password:
– After 10 minutes without key-pressing, the highest protection
level is automatically activated.
– Select the menu Display/Options / Viewing only.
The highest level of protection is activated.
 Administrator access through connecting the electronic key: The
protection is restored by disconnecting the electronic key
5.4 Editing the list of sensors

The Edit list of sensors display provides an overview of all IQ sensors and inac-
tive datasets (see section 9.3.2).
86 ba76188d01 03/2017
In the Edit list of sensors display, you can:

 assign sensor names (see section 5.4.1)
 delete inactive datasets (see section 5.4.1)
 change the order of the display of measured values on the measured value
display (see section 5.4.2).
5.4.1 Entering / editing a name for an IQ sensor
For the easier identification of the IQ sensors you can assign an individual name
to each IQ sensor.

2 Using <> and <OK>, select and confirm the menu item, System
settings -> Edit list of sensors.
The Edit list of sensors display opens.
3 Using <>, highlight the Sensor name column. Confirm with
<OK>.
4 Using, <> highlight the name of a sensor and confirm with
<OK>.
5 Enter the name with <> and <OK> and confirm with <OK> (see
section 5.4.1).
ba76188d01 03/2017 87
5.4.2 Changing the display position
The numbering of the sensors is generated by the system. The order of the sen-
sors in the measured value display and in the Edit list of sensors overview can
be individually determined.

3 Using <>, highlight the Model column. Confirm with <OK>.
4 Press <> to highlight a Model and confirm with <OK>.
A dialog window opens.
Fig. 5-5 Edit list of sensors -> Set display position
5 Using <>, select the menu item, Set display position and con-
firm with <OK>. A dialog window opens.
6 Press <> to select the required number for the display position
The sensor is displayed at the new position in the list of sensors. The
other sensors are moved accordingly.
5.4.3 Erasing inactive sensor datasets
An inactive dataset for an IQ sensor arises if the Universal Transmitter receives

no signals from an already registered IQ sensor. The Error display appears on
the measured value display instead of a measured value. Inactive datasets can
be recognized by a question mark, e.g. "?01" in the Edit list of sensors overview.
88 ba76188d01 03/2017
An inactive dataset can be reactivated by assigning it, e.g. to an IQ sensor of

the same type (see section 9.3.2). All settings are retained. If these data are no
longer required, they can be erased. All the data and settings and the link with
an output belonging to this IQ sensor are erased by this action.

3 Using <>, highlight the Model column. Confirm with <OK>.
4 Press <> to highlight a Model and confirm with <OK>.
Fig. 5-6 Edit list of sensors -> Erase inactive sensor
5 Using <>, select Erase inactive sensor and confirm with <OK>.
The dialog window for the security prompt appears.
6 Using <>, select Erase inactive sensor and confirm with <OK>.
The inactive sensor is erased.
5.5 Settings for sensors

Sensor settings include the measured parameter, measuring range and, if
necessary, compensations.
Enhanced sensor For certain sensors, special representation types and settings are available in
functions the menu, Extended sensor functions. An example for an enhanced sensor
function is the editing of measured values as a graphic representation with
cursor and zoom function (e.g. echo profile for the sludge level sensor
IFL 700 IQ).
ba76188d01 03/2017 89
Sensor settings The following diagram shows the operating steps to call up the sensor setting
menu and enhanced sensor functions:
All sensors Sensors with enhanced

sensor functions
Measured value display
(Sensor - plug-in)
Settings Sensor
Settings of sensors Display / options
Column, measuring range

Column, measuring range
Enhanced sensor functions

Sensor
Note : links are deleted Sensor settings
Sensor setting menu
Fig. 5-7 Calling up the sensor settings
If the measuring mode or measured parameter are changed, a link

of the sensor with a relay is erased!
Details on sensor settings are given in the operating manual for the
IQ sensor.
90 ba76188d01 03/2017
5.6 Sensor-sensor link

(automatic offset of an influencing quantity)
The Sensor-sensor link function automatically makes available the measured
value of a sensor to another sensor in the IQ SENSORNET system.
Example: D.O. sensors measure the D.O. partial pressure and use the solubility function
Measuring the D.O. of oxygen in the test sample to calculate the D.O. concentration (mg/l).
concentration The solubility of oxygen in water is influenced by the salt content (the salinity) of
the solution and other factors such as the temperature or air pressure.
Static salinity To take into account the influence of the salinity on the D.O. concentration,
correction many D.O. measuring systems provide a function where you can manually enter
the salinity value. The sensor includes the salinity and provides a corrected
measured value.
This type of static salinity correction is especially suitable for test samples with
almost unchanging salinity.
To obtain optimum measurement results even with changing salinity values, the
actual salinity has to be newly determined and entered for each measurement
of the D.O. concentration.
Dynamic salinity A dynamic salinity correction is provided by the Sensor-sensor link function.
correction This function supplies the D.O. sensor continuously with the current salinity
value and is thus especially suitable for the continuous measurement of the D.O.
concentration with changing salinity values.
5.6.1 Establishing the sensor-sensor link
Requirements for a The following requirements have to be met for a sensor-sensor link:
sensor-sensor link  Hardware
– A sensor for which an influence quantity can be corrected (e. g. FDO® 700
IQ, TriOxmatic® 700 IQ) is in the IQ SENSORNET system.
– A sensor that measures the influence quantity (e.g. TetraCon® 700 IQ) is
in the IQ SENSORNET system.
 Software
– The software of the sensor with correction function (e.g. FDO® 700 IQ)
supports the Sensor-sensor link function.
– The software of the sensor measuring the influence quantity (e.g.Tetra-
Con® 700 IQ) supports the Sensor-sensor link function.
 Sensor settings
– The correction function is enabled in the setting menu for the sensor with
ba76188d01 03/2017 91
correction function (e.g. FDO® 700 IQ).

– The automatic (dynamic) correction is enabled in the setting menu for the
sensor with correction function (e.g. FDO® 700 IQ).
– A sensor measures the influence quantity and displays it with the unit
which is used for manual input in the menu of the sensor with correction
function (e.g. TetraCon® 700 IQ measures the salinity - salinity is quoted
dimensionless).
– The manually entered value for the static correction is set to the mean
value of the influence quantity (e.g. salinity value) of the test sample.
If no measured value for the influence quantity is available, the correction
is made with the value that was manually entered (static correction).
Establishing the
1 Using <S>, open the Settings menu.
link
2 Using <><> and <OK>, select and confirm the menu item, System
settings -> Sensor-sensor link.
The Sensor-sensor link overview opens.
The displayed list includes all sensors with which the correction of an
influence quantity is possible (e.g. FDO® 700 IQ).
3 Using <><>, highlight a sensor and confirm with <OK>.

The influence quantity to be linked and the current state of the link are
displayed.
92 ba76188d01 03/2017
4 Using <><>, highlight a parameter to be linked, and confirm with

<OK>.
The displayed list includes all sensors that measure an influence quan-
tity with the correct unit (e.g. TetraCon® 700 IQ, which measures the
salinity in mg/l).
5 Using <><>, highlight a sensor that can be linked, and confirm with
<OK>.
The sensors are linked.
The influence quantity to be linked and the linked sensor
are displayed.
6 Leave the system settings with <M>.
In the measured value display, the corrected measured value is marked
by an asterisk (*).
ba76188d01 03/2017 93
Behavior if there is Cause Behavior

no measured value
for the influence – Sensor failure – The manually entered value for the influence quan-
quantity tity is automatically used for correction.
An exclamation mark (!) indicates the interrupted
link.
– The sensor-sensor link is reactivated as soon as the
measured value for the influence quantity is avail-
able again.
– Maintenance con- – The value last measured for the influence quantity is
dition active automatically used for correction.
– The current measured value is used for correction
as soon as the measured value for the influence
quantity is available again.
5.6.2 Erasing a Sensor-sensor link

2 Using <><> and <OK>, select and confirm the menu item, System
settings -> Sensor-sensor link.
The Sensor-sensor link overview opens.
The displayed list includes all sensors with which the correction of an
influence quantity is possible (e.g. FDO® 700 IQ).
The displayed list includes all linked sensors.
The displayed list includes all sensors that measure an influence quan-
tity with the correct unit (e.g. TetraCon® 700 IQ, which measures the
salinity in mg/l) and the menu item Erase link.
5 Using <><>, highlight the menu item, Erase link, and confirm with
<OK>.
The sensor-sensor link is erased.
6 Leave the system settings with <M>.
In the measured value display, the measured value is corrected by the
manually entered value.
The Sensor-sensor link function is automatically deactivated if the

measured parameter of the linked sensor is changed (e.g. by
switching the display of the TetraCon® 700 IQ conductivity sensor
from salinity to conductivity).
94 ba76188d01 03/2017
5.7 Editing the list of outputs

The Edit list of outputs display provides an overview of all outputs, links and
inactive datasets (see section 9.3.3).
In the Edit list of outputs display, you can:
 assign output names (see section 5.4.1) and
 erase inactive datasets (see section 5.4.2).
5.7.1 Entering / editing the name of an output
For the easier identification of the outputs, you can assign an individual name to
each output in the Edit list of outputs display.

settings -> Edit list of outputs.
The Edit list of outputs overview opens.
3 Press <> to highlight a name in the Name column and confirm
with <OK>.
Fig. 5-8 Edit list of outputs -> enter a name
4 Enter the name with <> and <OK> and confirm with <OK> (see
also section 4.2.2).
ba76188d01 03/2017 95
5.7.2 Erasing an inactive dataset for an MIQ output module
An inactive dataset for an MIQ output module arises if the system receives no
signals from a registered MIQ output module. Inactive datasets can be recog-
nized by a question mark, e.g. "?01" in the Edit list of outputs overview.
An inactive dataset can be reactivated by assigning it, e.g. to an MIQ output
module of the same type (see section 9.3.3). All settings are retained. If you no
longer require the stored data, you can erase them.

The Edit list of outputs display opens.
3 Using <>and <OK>, highlight and confirm the Model/Channel
column. This column can only be highlighted if an inactive dataset (?xx)
is present.
4 Press <> to highlight a Model/Channel and confirm with <OK>.
96 ba76188d01 03/2017
Fig. 5-10 Edit list of outputs -> Erase output module
5 Using <>, select Erase output module and confirm with <OK>.
The dialog window for the security prompt appears.
6 Using <>, select Erase output module and confirm with <OK>.
The output is erased.
5.7.3 Output links/settings
The procedure and possible settings for linking outputs with sensors
are given in the operating manual of the respective output module.
5.8 Alarm settings
5.8.1 General information
Under this menu item you can specify reactions on certain alarm events.
An alarm event is when a certain measured value (limiting value) of a sensor is
exceeded or undercut.
Alarm events can be relayed as follows:
 As a message on the display
 As a relay action
 As an Email (see section 5.9.5)
ba76188d01 03/2017 97
An alarm message via display or relay cannot be acknowledged or

switched off. An alarm only disappears if the cause for the alarm
was eliminated or the Alarm settings were changed or erased.
5.8.2 Setting up / editing alarms

2 Using <> and <OK>, select and confirm the menu item, Alarm
settings.
The Alarm link overview dialog window opens.
Alarms that have already been set up have entries in the Sensor col-
umn.
Fig. 5-11 Alarm settings -> Alarm link overview
In the Sensor column, the sensor number (corresponding to the list

of sensors) and series number is named.
3 Select an alarm A01 to AXX to be edited with <>. To set up a

new alarm without entry select in the Sensor column. Then confirm with
<OK>. When a new alarm is set up a list with all sensors appears first.
Alarm links that are already available can be erased or edited (for edit-
ing continue with step 5).
98 ba76188d01 03/2017
Fig. 5-12 Select sensor for alarm link
4 To set up a new alarm, select a sensor from the list with <> and
confirm with <OK>. The Set alarm link display opens.
Fig. 5-13 Set alarm link
5 Edit the setting table. The required operating steps are described in
detail in section 4.2 GENERAL OPERATING PRINCIPLES.
Alarm links setting

table
Menu item Selection/Values Explanations
Measured variable  Main variable Main variable designates the actual mea-
 Adjoining variable sured parameter of the sensor (e.g. pH,
oxygen, etc.).
Adjoining variable designates an addi-
tional measured parameter (e.g. tempera-
ture).
ba76188d01 03/2017 99
Menu item Selection/Values Explanations

Limit value  Lower limit Type of the alarm event.
 Upper limit Lower limit: An alarm is triggered if the
defined limit value is undercut.
Upper limit: An alarm is triggered if the
defined limit value is exceeded.
Lower limit / within the measuring Limit value for the alarm event
Upper limit range (sensor-depen-
dent)
Hysteresis 0 - 10 % of the measur- Hysteresis for the limit value
ing range
Designation (max. 20 characters) User-defined designation for easier identi-
fication in the alarm message.
Relay output Dxx / .../Ry Opens a list with all relay outputs where
... the Alarm contact is set.
...
Dxx: number of the output module
...
.../Ry: relay output channel
No relay output
Here you can select a relay output. When
the alarm event occurs, it carries out the
specified action (Open or Close). For
details, see section 5.8.3 ALARM OUTPUT
TO DISPLAY.
Accept The settings are taken over in the setting

table by pressing <OK>. The display
switches to the next higher level.
Cancel The display switches to the next higher
level without storing the new settings.
5.8.3 Alarm output to display
When an alarm event occurs, a window with a text message appears.
100 ba76188d01 03/2017

1
2
3
4
5
Fig. 5-14 Example of an alarm message on the display
1 Alarm no. Axx and date and time of the alarm event
2 User-defined designation
3 Sensor number and model name of the sensor that triggered the
alarm event
4 Series number and name of the sensor that triggered the alarm event
5 Description of the event with specification of the limiting value:
"<" = Undercut
">" = Exceeded
Operating If there are several alarm messages indicated on the display, you can scroll
instructions through the messages with <>. This can be recognized from the page
number in the right lower corner. The latest message is always on the first posi-
tion.
Pressing <M> hides the alarm messages and switches to the measured value
display. After one minute the alarm messages appear again if what caused them
is still present.
5.8.4 Alarm output as relay action
The relay outputs of the IQ SENSORNET can be configured so a relay action is

triggered when an alarm event occurs (Open or Close). For this the Alarm
contact function must be set for the relay output in the Settings of outputs and
links.
The Alarm contact function is only available for relays that are not linked with a
sensor. If necessary, an existing link must be erased. For details please refer to
the operating manual of the output module.
5.8.5 Alarm message as Email (variant -E, EF)
All alarm messages can be sent to an Email address. In this case, the same
information that is output on the display is transmitted. For details, see section
5.9.5.
ba76188d01 03/2017 101

For critical alarm events take into account that Email messages may
possibly be received delayed.
5.9 System settings

System settings include:
 Change password (see section 5.9.1).
 Language (see section 5.1)
 Date/Time (see section 5.9.2)
 Location altitude/Air pressure (see section 5.9.3)
 TCP/IP settings (variant -E, EF)
 email (variant -E, EF)
 Settings bus interfaces (variant -MOD, -PR, -EF)
 Function code
5.9.1 Changing the password
A password protects the system settings against inadvertent changes. The

password must always be entered in order to change the release of the settings.
The password is set to 1000 in the delivery state.

settings -> Change password.
The Change password dialog window opens.
102 ba76188d01 03/2017

Fig. 5-15 System settings -> Change password
3 Using <> and <OK>, select and confirm the menu item,
Change password. The dialog window for entering the password opens.
4 Press <> and <OK> to enter the new password and press
<OK> to confirm. The setting is changed.
5.9.2 Setting the date and time
The real time clock is used for the display of date and time in the measured value
display and in log book entries.

settings -> Date/Time.
The Date/Time display opens.
3 Press <> to select Set date or Set time.
4 Confirm the selection with <OK>.
A field is highlighted, e.g. Year.
ba76188d01 03/2017 103

Fig. 5-16 Date/Time
5 Press <> and <OK> to select and confirm a number.

The next field is highlighted, e.g. Month.
6 Complete the entries on the display Date/Time.
The clock in the DIQ/S 28X bridges periods of power failure of up to

several hours. After a longer power failure, the clock starts precisely
at the time of the failure. A message and an entry in the log book
provide information on the power failure and the necessity for reset-
ting the clock.
5.9.3 Location altitude / average air pressure
Air pressure values can be set within a range of 500 to 1100 mbar.

settings -> Location altitude/Air pressure.
The Location altitude/Air pressure display opens.
104 ba76188d01 03/2017

Fig. 5-17 Location altitude/Air pressure
3 Press <> to select Set altitude of location or Set air pressure

4 Press <> to change the values for Loc. altitude or Air pressure
5.9.4 TCP/IP settings (variant -E, EF)
The TCP/IP settings menu includes functions and settings for the operation of
the DIQ/S 28X in an Ethernet network.

settings -> TCP/IP settings.
The TCP/IP settings display opens.
Fig. 5-18 TCP/IP settings
ba76188d01 03/2017 105

3 Press <> and <OK> to select and confirm a menu item.

An entry field or selection list opens up.

ues
DHCP Yes The IQ SENSOR NET is configured as a DHCP cli-
ent.
If a DHCP server is in the network, the
IQ SENSOR NET receives all further network set-
tings from the DHCP server.
No The IQ SENSOR NET is not configured as a
DHCP client.
All other settings have to be made as necessary.
IP address Address Permanent IP address for the IQ SENSOR NET in
the LAN (if DHCP No).
Subnet mask Address Subnet mask (if DHCP No).
The subnet mask depends on the network size
(for small networks: e.g. 255.255.255.0).
DNS server Address Entry for fieldbuses not required.
For a connection with the Internet (if DHCP No),
e.g.:
 IP address of the DNS server in the network
 Entry of IP address or e.g. 127.0.0.1
Standard gateway Address Entry for fieldbuses not required.
For a connection with the Internet (if DHCP No),
e.g.:
 IP address of the instrument providing access
to the Internet
 Entry of IP address or e.g. 127.0.0.1
4 Enter texts with <> and <OK>, or select and confirm an option
from the list.
5 Complete the entries on the display TCP/IP settings.
5.9.5 email (variant -E, EF)
The email menu contains functions and settings for the sending of alarm mes-
sages via Email.
106 ba76188d01 03/2017


settings -> email.
The email display opens.
Fig. 5-19 email settings
3 Press <> and <OK> to select and confirm a menu item.

An entry field or selection list opens up.

ues
SMTP Server Address Address of the SMTP server of the Email pro-
vider through which the Email will be sent.
User name Name User name of the Email account
Password Character string Password to log on to the Email account
From Name Email sender address
Alarm send to Name Email target address
Send test email A test Email with the specified settings is sent.
4 Enter texts with <> and <OK>, or select and confirm an option
from the list.
5 Complete the entries on the display email.
ba76188d01 03/2017 107

6 Using <> and <OK>, select and confirm the menu item, Save
and quit.
The settings are stored. The menu ist closed.
5.9.6 Settings bus interfaces (variant -E, EF)
The Settings bus interfaces menu contains functions and settings for the
communication of the IQ SENSORNET with a fieldbus. Prerequisite: An interface
to a fieldbus is available (hardware, optional).
For details, see operating manual ba77010 "IQ SENSORNET Fieldbus linking",
for download at www.YSI.com.
5.9.7 Function code
Function for the service staff.
5.10 Measured value logging

With the Measured value logging setting you can record and store measured
values of IQ sensors.
You can display the stored measured values
 as a list or
 display the temporal course of the stored measured values graphically (see
section 4.4.4).
 display the stored measured values to a PC.
The system allocates memory blocks to an IQ sensor for the Measured value
logging. With a recording interval of 1 measurement dataset per minute, a
recording duration of 1 day per memory block is possible. 360 memory blocks
are available and can be distributed to the sensors.
The recording duration directly depends on the recording interval. If a recording
duration of 0 d is set for a sensor, there is no memory block allocated to the
IQ sensor. The Dur. setting also contains the number of the allocated memory
blocks (see table).
Recording interval Possible recording durations with the given recording interval
1 min 0d 1d 2d 3d ... 360 d
5 min 0d 5d 10 d 15 d ... 1800 d
10 min 0d 10 d 20 d 30 d ... 3600 d
108 ba76188d01 03/2017

Recording interval Possible recording durations with the given recording interval
15 min 0d 15 d 30 d 45 d ... 5400 d
30 min 0d 30 d 60 d 90 d ... 10800 d
60 min 0d 60 d 120 d 180 d ... 21600 d
5.10.1 Setting the recording interval (dt) and recording duration (Dur.)

2 Using <> and <OK>, select and confirm the menu item, Mea-
sured value logging.
The Measured value logging display opens.
It contains a list of all sensors and inactive sensors.
Fig. 5-20 Measured value logging
3 Press <> and <OK> to select and confirm the dt column.

4 Press <> and <OK> to select and confirm a sensor.
5 Determine the recording interval with <> and <OK>.
When the recording interval is changed, the recording duration changes
at the same time (Dur.), because the recording duration results from the
recording interval due to a fixed number of memory blocks.
6 Switch to the selection of columns with <ESC>.
7 Press <> and <OK> to select and confirm the Dur. column.
8 Press <> and <OK> to select and confirm a sensor.
ba76188d01 03/2017 109

9 Select the recording duration with <> and <OK>.

The recording duration is always increased or decreased in the same
steps.
The percentage of the memory blocks not yet allocated is shown on

the display. If all memory block are occupied (Free storage: 0%), the
number of memory blocks allocated to another IQ sensor may have
to be reduced.
When the number of memory blocks for a sensor is reduced, the memory block
with the oldest data is erased. All other data is retained.
For inactive IQ sensors, the Dur. setting can only be reduced.
10 Switch to the selection of columns with <ESC>.

11 Press <> and <OK> to select and confirm the Save and quit
column.
The changes are stored.
The Einstellungen/Settings display opens.
If the changes made for recording duration or recording interval

should not be stored, press <> and <OK> to select and con-
firm the Quit field.
110 ba76188d01 03/2017

DIQ/S 28X Ethernet connection (variant -E, -EF)
6 Ethernet connection (variant -E, -EF)

If the Universal Transmitter DIQ/S 28X-E is connected to an Ethernet network,
communication with the IQ SENSORNET System 28X is enhanced and facilitated.
 The Ethernet interface allows the DIQ/S 28XE[F] to be integrated into a local
network and to be connected to other networks (e.g. Internet) using commer-
cially available network technology.
 The web server des DIQ/S 28X-E[F] makes available the measurement data
of the IQ SENSORNET as a web page.
 Communication with the DIQ/S 28X-E[F] is possible via a large number of
network-capable terminals.
– Internet-capable devices with web browser (e.g. PC, smartphone, tablet
PC) can display the measurement data of the IQ SENSORNET.
– The programs of the IQ WEB CONNECT can be used to operate and man-
age the IQ SENSORNET on a PC.
 Extraction of the data provided by the web server is possible using commer-
cially available or self-created programs (DataLogger).
 With the Ethernet interface of the variant DIQ/S 28X-EF, the instrument can
additionally be integrated into an EtherNet/IP™, Profinet and Modbus TCP
environment. Details on this subject are given in the operating manual
("IQ SENSORNET fieldbus linking"). The current version can be found on the
Internet at www.YSI.com.
6.1 Configuring the Ethernet network

The following overview helps in the general planning, project planning and
installation of a network connection of the DIQ/S 28X-E[F].
A basic understanding of network technology is useful for setting up a local net-
work and especially the connection to the Internet.
Various settings are to be made on the individual network subscribers according
to the configuration of the network.
Insofar as the settings affect network subscribers of third-party vendors (e.g. the
router), only a general reference is made here to the setting. For details, of the
menus in which the settings are made, please refer to the respective operating
manual for your device.
If you have no knowledge of networks, please contact your network adminis-
trator.
ba76188d01 03/2017 111

Ethernet connection (variant -E, -EF) DIQ/S 28X
PC SmartPhone
local area network

(L A N) Router
DSL / mobile wireless
Router (Internet Service Provider)

INTERNET Router (Internet Service Provider)
DSL / mobile wireless Router IP on the Internet

Router e. g. 88.11.12.13
Router IP in the LAN
local area network e. g. 192.168.20.1
(L A N)
DIQ/S 28X-E
IP in the LAN IP in the LAN

e. g. 192.168.20.3 e. g. 192.168.20.2
Fig. 6-1 DIQ/S 28X-E[F] in a local network and on the Internet (example)
112 ba76188d01 03/2017

6.1.1 Communication in a local network (LAN)
Prerequisites Details / Examples / Designations

Hardware IQ SENSOR NET Universal Transmitter
System 28X DIQ/S 28X-E[F]
Ethernet cable RJ45 cable to connect the IQ SENSOR NET
and router.
Note: If the DIQ/S 28X-E[F] is located at an
open air test site, please note section 6.2.
Terminal equipment  PC
(a network subscriber that  Tablet PC
sets up the communica-
tion), e.g.:  Smartphone
Software Communication software  web browser

on the terminal equipment,  programs of the IQ WEB CONNECT
e.g.: (for PC only)
Network services  WINS server
(e.g. on the terminal device  with DHCP and DNS servers
or router) (for network access in the LAN
via the name of the DIQ/S 28X-E[F])
Network address of the  Instrument name (is specified in the terminal settings of the Universal
Universal Transmitter in Transmitters (siehe section 5.2).
the LAN When delivered, the combination of instrument name + serial number
is entered as the name (e.g. S284-16160001).
or
 Fixed local IP address of the Universal Transmitter (defined in the set-
tings of the Universal Transmitter (see section 6.1.2).
ba76188d01 03/2017 113

6.1.2 Communication on the Internet
Prerequisite Details / Examples / Designations

Hardware IQ SENSOR NET Universal Transmitter
System 28X DIQ/S 28X-E[F]
Router, e.g.  DSL router
 Mobile wireless router
Ethernet cable RJ45 cable to connect the DIQ/S 28X-E[F]
and router.
Note: If the DIQ/S 28X is located at an open
air test site, please note section 6.2.
Terminal equipment  PC
(network subscriber that  Tablet PC
sets up the communica-
tion), e.g.:  Smartphone
Software Communication software  web browser

on the terminal equipment,
e.g.:
Network address of the The network address of the router on the Internet is configured via an
DIQ/S 28X-E[F] on the Internet service (see below).
Internet
Internet services Internet access with data  DSL connection
flat rate, e.g.:  Mobile wireless connection (SIM card)
Internet service which  A public IP address
makes the router publicly (e.g. available at an Internet service pro-
addressable on the Inter- vider)
net, e.g.:  A service (e.g. DynDNS), which assigns
a fixed name to a changing IP address of
an Internet subscriber so that the sub-
scriber is always accessible under the
same name
114 ba76188d01 03/2017

Prerequisite Details / Examples / Designations

Special settings of the IQ SENSOR NET Menu:
network subscriber Universal Transmitter System settings /
DIQ/S 28X-E[F] TCP/IP settings:
 DHCP: No
 IP address:
Enter a fixed IP address (the IP address
must lie outside the address range of the
DHCP server (the DHCP server is often
a network service of the router)
 Subnet mask:
The IP address depends on the local
network (in home networks, e.g.
255.255.255.0)
 DNS server:
Local IP address of the router (e.g.
192.168.179.1)
 Standard gateway:
Local IP address of the router (e.g.
192.168.179.1)
Router  Data for Internet access
(from Internet service provider)
(see operating manual for  Port forwarding
your router) of port 8080 to port 80 of the fixed IP
address of the DIQ/S 28X
ba76188d01 03/2017 115

6.2 Ethernet connection if mounted at an open air test site (DIQ/

S 28X-E[F])
The RJ45 socket does not protect sufficiently against moisture. At an open test
site, the moisture protection device (ADA/E) available as an accessory has to be
mounted for safe Ethernet communication (see section 11.
6.3 Establishing the connection with the DIQ/S 28X via a network
6.3.1 Opening the IQ WEB CONNECT
The web server of the DIQ/S 28X provides functions for the (remote) operation
of the DIQ/S 28X and for the data exchange (e.g. with a PC) via a network
address.
Prerequisites  All network components (Universal Transmitter, router, network-capable

devices with browser) are connected
 The network services are active
 Web browser (HTML 5)
The IP address and the other network settings for the Universal
Transmitter DIQ/S 28X are configured in the System settings ->
TCP/IP settings menu.
Procedure Enter the network address of the DIQ/S 28X in the address line in the web
browser
1 Enter the network address of the Web browser DIQ/S 28X-E[F] in the
address line of the web browser.
 in the LAN
e.g. name or IP address of the DIQ/S 28X-E[F]
 on the Internet,
e.g. fixed IP address of the router or DynDNS name
The network connection to the DIQ/S 28X-E[F] is established.
The start page of the IQ SENSOR NET is displayed.
116 ba76188d01 03/2017

Fig. 6-2 IQ WEB CONNECT start page
The IQ WEB CONNECT start page of the DIQ/S 28X-E[F] provides links to
the following functions:
 "IQ WEB CONNECT Terminal"
(operating the DIQ/S 28X-E[F])
 "IQ WEB CONNECT DatalogTransfer"
(transmitting measurement data)
 "IQ WEB CONNECT ConfigSaveLoad"
(saving and loading the system configuration of the DIQ/S 28X-E[F])
2 Open a link on the IQ WEB CONNECT start page.

3 Enter the user name and password
(user name and password are defined in the settings of the access
control of the DIQ/S 28X-E[F].
Default setting: User name "ADMIN", password "1111")
The selected website is displayed.
6.3.2 IQ WEB CONNECT Terminal
With the "IQ WEB CONNECT Terminal", you can operate your DIQ/S 28X-E[F]
just like you are used to on the instrument.
ba76188d01 03/2017 117

You can save data to a USB memory device connected to the instru-
ment (similar to operation of the instrument). To save data to a PC,
select the function "IQ WEB CONNECT DatalogTransfer" (see
section 6.3.3).
Fig. 6-3 IQ WEB CONNECT Terminal
6.3.3 IQ WEB CONNECT DatalogTransfer
"IQ WEB CONNECT DatalogTransfer" exchanges data with the termi-

nal device with which you are carrying out IQ WEB CONNECT func-
tions. The data exchange is optimized for the following operating
systems:
 Microsoft® Windows®
 Linux
Via the website "IQ WEB CONNECT DatalogTransfer", you can save measure-
ment data of the DIQ/S 28X-E[F] directly to a PC.
The transmitted measurement data are stored in a separate file in CSV data
format for each sensor. The file name (e. g. S03_TriOxmatic700IQ_1.csv) is
automatically assigned and includes:
 sensor number (e. g. S03)
 sensor model (e. g. TriOxmatic700IQ)
 consecutive number.
118 ba76188d01 03/2017

For processing you can open the csv file, e.g. with Microsoft Excel.
2 3 4 5 6 7 8 9
Fig. 6-4 Example of a CSV file after being imported into Microsoft Excel
1 Identification of the measurement data (from left to right, line 1)

– Sensor number (Sxx)
– Sensor model
– Sensor name
– Serial number (sensor)
– Date and time of the file save
2 Date and time of the measured value save
3 Measured value status
4 Measured value
5 Unit of the measured value
6 Measured parameter
7 Measured value status of the secondary measured value
8 Secondary measured value
9 Unit of the secondary measured value
The measured values are transmitted unprocessed. Therefore, the

measured values may have a number of decimal places that
exceeds the display accuracy of the respective sensor.
When you want to display and process the transmitted measured
values, it may be required to limit the number of digits (e. g. by
rounding).
ba76188d01 03/2017 119

6.3.4 IQ WEB CONNECT ConfigSaveLoad
"IQ WEB CONNECT DatalogTransfer" exchanges data with the termi-

nal device with which you are carrying out IQ WEB CONNECT func-
tions. The data exchange is optimized for the following operating
systems:
 Microsoft® Windows®
 Linux
Via the website IQ WEB CONNECT ConfigSaveLoad, you can display or save the
system configuration of the DIQ/S 28X-E[F] or load it to a DIQ/S 28X-E[F].
The system configuration comprises the following data:

 Settings of sensors and diff. sensors
 Settings of outputs and links
 Edit list of sensors
 Edit list of outputs
 Measured value recording (data logger settings)
 Language
 Access control
 Alarm settings
 System settings
6.4 Communication with fieldbuses (DIQ/S 28X[-XX]-EF)

Details on communication with fieldbuses are given in the operating manual
ba77010e ("IQ SENSORNET fieldbus linking"). The current version can be found
on the Internet at www.YSI.com.
6.5 Troubleshooting
The Universal Transmitter DIQ/S 28X provides an Ethernet interface for the
connection of the IQ SENSORNET to private networks, company networks and
public networks.
To establish accessibilty of the IQ SENSORNET in a public network (e.g. Internet),
external services (e.g. Internet access, fixed public IP address etc.) are
required.
A detailed error analysis for connection errors is not possible within the scope of
this operating manual because of the multitude of service providers, network
architectures and connection options involved.
120 ba76188d01 03/2017

Here is a selection of possible causes for network/connection problems. If there

are other connection problems, contact your network administrator or a network
specialist.
No network Cause Remedy

connection
– Ethernet hardware defective, – Exchange the Ethernet hardware
e.g.
– Ethernet cable defective
– Ethernet connection on
the DIQ/S 28X or router
defective
– Incorrect network address – Enter the correct name:
entered in the LAN (name) "Instrument name-serial number",
replace special characters (/, spaces,
etc.) with "-", e.g. DIQ-S284-16160001
– Ascertain or define the correct IP
address of the DIQ/S 28X in the local
network (e.g. IQ SENSORNET setting +
router setting) and enter it.
– Incorrect network address on – Ascertain or define the correct Internet
the Internet (IP address of the IP address of the router (e.g. FixedPub-
router) licIP) and enter
– A network connection from a – 2nd IQ WEB CONNECT
terminal device to the DIQ/
S 28X (IQ WEB CONNECT)
already exists
– Incorrect setting in the router – Correct the settings
(e.g. Internet access data, port
forwarding)
– Incorrect setting in the DIQ/ – Correct the settings
S 28X (System menu/TCP/
IP settings)
– Ports which are used by the – Have your network administrator
DIQ/S 28X are already assign you free ports
assigned to other devices in – Specify the port (1-65535) manually in
the network (e.g. another the address line of the browser/
IQ SENSORNET system) IQ WEB CONNECT (example: http://
10.11.12.13:65535)
– Forward this port (65535) in the router
to the IP address of the DIQ/S 28X.
– Blocking by firewall – Contact your network administrator or a
network specialist
ba76188d01 03/2017 121

6.6 Technical network terms
DHCP DHCP is a network service which automatically assigns an IP address

(Dynamic Host Config- to a network subscriber.
uration Protocol) In local networks, this function is mostly carried out by the router.
DNS DNS is a network service which manages the name of a subscriber
(Domain Name Sys- on the Internet (e.g. www.google.com) and the associated IP address
tem) e.g. "http://74.125.224.72/".
In local networks, this function is mostly carried out by the router.
DynDNS DynDNS is an Internet service which makes a subscriber with
(Dynamic DNS) changing (dynamically issued) IP address accessible under a fixed
name on the Internet.
Prerequisite: The router in the local network must support DynDNS
and must always send its current dynamic public IP address to the
Internet service.
Firewall A firewall protects a device or a local network against attacks from the
Internet.
A firewall blocks the communication interfaces (ports) that are not
used for standard communication (web browser, E-mail etc.).
IP address A network address identifies a subscriber in a network.
Private IP addresses are IP addresses specially reserved for home

networks (range 192.168.0.0 to 192.168.255.255). In most cases,
they are automatically assigned by the router which manages the
local network. They are used to uniquely identify the individual
subscribers within a local network.
Routers provide the possibility to manually assign a fixed local IP
address for individual devices.
Public IP addresses are automatically assigned to the router in the

local network (LAN) by the Internet Service Provider (ISP). They are
used to uniquely identify an Internet subscriber (a home network or
even an individual device) to the Internet. They are mostly only valid
for the duration of an Internet session (dynamic IP address) and are
released again upon ending the Internet connection.
An Internet user can also be assigned a fixed public IP address via
(chargeable) Internet services.
ISP An ISP is an Internet service provider which provides Internet access.
(Internet Service Pro-
vider)
122 ba76188d01 03/2017

Port A port is the communication interface of an application (possible port

numbers: 0-65535).
Some ports (port numbers) are reserved for special applications, e.g.:
 21: FTP (File Transfer Protocol)
 25: SMTP (Simple Mail Transfer Protocol)
 80: HTTP (Hypertext Transfer Protocol)
(used by the web browser for communication with web servers)
Port forwarding If a router receives a communication request on a port for which
forwarding is configured, communication is forwarded to the port of a
network subscriber which is defined in the forwarding rule.
In local networks, this function is mostly carried out by the router.
Router A router fulfills the following tasks as an interface between two
networks:
 It connects the local network to the Internet.
 It controls the communication of network devices within a local net-
work and manages the local IP addresses of the subscriber. In the
local network, it is also possible to manage names for individual IP
addresses (DHCP) in most cases.
Routers often assume other services in a network, e. g.:
 DNS (assigning of names to IP addresses)
 Firewall (protects the network subscriber against attacks from the
Internet)
 Port forwarding
TCP/IP The Internet Protocol is the common language (protocol) of the
(Transmission network subscriber.
Control Protocol /
Internet Protocol)
ba76188d01 03/2017 123

Outputs DIQ/S 28X
7 Outputs
7.1 Outputs of the System 28X
Functioning of the outputs
 Relay outputs work as openers or closers.
 Current outputs provide a current depending on the measured value.
Current outputs are available in the variants DIQ/S 28X-CRX and when an
extension module with current outputs is used).
On the DIQ/S 28X you can do the following:

 Assign names for the outputs (see section 7.3).
 Link outputs with sensors (see section 7.4)
 Erase links between outputs and sensors (seesection 7.5)
 Set up outputs (see section 7.6 and section 7.7)
 Check the conditions of the outputs (see section 7.8)
Basis information on the use of relay outputs is given in section 7.2.
Functions for Relay output (see section 7.6)

current and relay
outputs  System monitoring
 Sensor monitoring
 Limit indicator
 Frequency controller
 Pulse-width output
 Cleaning
 Sensor-controlled
 Manual control
 Alarm contact
Current output (see section 7.7)
 Recorder
 PID controller
 Fixed current value
124 ba76188d01 03/2017

DIQ/S 28X Outputs
7.2 Basic information on relay functions

This chapter describes general basic information concerning the following relay
functions:
 Monitoring (see section 7.2.1)
 Limit indicator (see section 7.2.2)
 Proportional output (see section 7.2.3)
7.2.1 Monitoring
When using a relay for monitoring, a relay action (Open, Close) occurs when
certain states occur. This function is suitable, for example, for the monitoring of
errors in the system.
For monitoring functions, use the relay preferably as normally

closed (see section 7.6.1). In the case of an error, the relay opens.
As a result, the monitoring function operates even if, for instance,
the supply voltage fails.
7.2.2 Limit indicator
With a limit indicator, a relay switches when a specified limiting value is

exceeded or undercut.
Limit indicators can be used in the following way:
 Monitoring a limiting value using a relay:
when a limiting value (upper or lower limiting value) is exceeded or undercut,
a relay switches. The Open or Close relay actions are possible in each case
(see page 126).
 Monitoring two limiting values using two relays:
If the upper limiting value is exceeded or undercut, a relay switches, and if
the lower limiting value is exceeded or undercut, another relay switches. The
Open or Close relay actions are possible in each case (see page 126).
If the simple monitoring function (Open, Close) with one or two

relays is not sufficient, use proportional output (see section 7.2.3).
ba76188d01 03/2017 125

Outputs DIQ/S 28X
Monitoring limit-
ing values using Measured t1
one or two relays value
Relay 1 t1
UL
Hysteresis UL
2
1 4 6
3
5
Hysteresis LL
LL Relay 2
t2 t2
Ti
1 Upper limit value (relay 1) exceeded

2 Selected switching delay t1 for relay 1 1 expired
Relay 1 switches
3 Hysteresis for upper limiting value (relay 1) undercut
4 Selected switching delay t1 for relay 1 1 expired
Relay 1 switches back
5 Lower limit value (relay 2) undercut
Selected switching delay t2 for relay 1 1 expired
Relay 2 switches
Fig. 7-1 Switching points for relays with the function of a limit indicator
A switching delay (t) can be set up for each relay for switching processes. This
is the time period for which a limiting value must be exceeded before the relay
switches. This prevents frequent switching if the measured values are close to
the limiting value.
7.2.3 Proportional output
In the case of proportional output, a relay switches cyclically on and off in a

defined measured value range (proportional range). At the same time, the relay
switches with a:
 duration of operation that corresponds to the measured value (pulse-width
output, see page 128) or
 switching frequency (frequency output, see page 128).
126 ba76188d01 03/2017

DIQ/S 28X Outputs
Proportional outputs can be used in the following way:

 Output with one relay:
An output range is defined with a Start value and an End value. No output
takes place above and below the output range (see page 127).
 Output with two relays:
An output range is defined for each relay with a Start value and an End value.
One relay outputs in the upper output range and a further relay in the lower
output range (see page 127).
Output with one

relay Switching frequency f or
Pulse width v
100
90
Proportional
band
10
0 Measured value
1 2
Fig. 7-2 Output with one relay
Output with two

relays Switching frequency f or
Pulse width v
Proportional bands
100 Relay 1 and 2
90
10
0 Measured value
2 1 1 2
Relay 1 Relay 2
1 Start value
Measured value with a minimum pulse width or switching frequency
2 End value
Measured value with a maximum pulse width or switching frequency
Fig. 7-3 Output with two relays
ba76188d01 03/2017 127

Outputs DIQ/S 28X
Pulse width output The output of the pulse width is used, e.g. for controlling valves.
Pulse-width regulation changes the duration of operation (ton) of the output sig-
nal. Depending on the position of the measured value in the proportional range,
the relay is operated for a longer or shorter period.
Relay
tOn t Off
On
Off
Time [s]
T
Fig. 7-4 Relay output of the pulse-width output
The cycle duration (T) is made up of the turn-on and turn-off switching
duration (ton, toff) of the relay together. While the selected cycle duration
(T) remains constant, the turn-on duration (ton) changes depending on
the measured value and, with it, the pulse width (v). The pulse width can
be set from 0 % to 100 %.
v = (ton / T) * 100 %
v = pulse width, T = cycle duration, ton = turn-on duration
 If the measured value is at the end of the proportional range (End value), the
turn-on duration (ton) is long, the turn-off duration is short. This means the
relay operates for a longer period.
 If the measured value is at the beginning of the proportional range (Start
value), the turn-on duration (ton) is short, and the relay operates for a corre-
spondingly shorter period.
If the duration of the closing or opening pulse is shorter than 0.1 s,

the relay remains open or closed for the complete cycle duration.
Frequency output Switching frequency output is used, e.g. for controlling dosing pumps.
In contrast to the pulse-width output, the pulse width is not modulated with the
frequency output but the switching frequency of the output signal. Depending on
the position of the measured value in the proportional range, the relay is
switched more often or less often.
128 ba76188d01 03/2017

DIQ/S 28X Outputs
Relay
tOn = 0.3 s
On
Off
T Time [s]
Fig. 7-5 Relay output of frequency output
While the selected switching duration (ton = 0.3 s) always remains con-
stant, the switching frequency at which the relay switches changes
depending on the measured value.
 If the measured value is at the end of the proportional range (End
value), the switching frequency is higher.
 If the measured value is at the beginning of the proportional range
(Start value), the switching frequency is low.
Characteristic Through the selection of the Start value and End value, the proportional output
curves can be operated with a positive or negative characteristic curve.
 Positive characteristic curve:
Select the End value to be greater than the Start value.
The turn-on duration or frequency increases with an increasing measured
value (see page 131).
 Negative characteristic curve:
Select the End value to be smaller than the Start value.
The turn-on duration or frequency decreases with an increasing measured
value (see page 132).
The maximum values for the pulse width or switching frequency are assigned to
the End value value and the minimum values for turn-on duration or frequency
are assigned to the Start value value.
ba76188d01 03/2017 129

Outputs DIQ/S 28X
Switching frequency f or
Pulse width v
Max.
Min.
Measured value
Start value End value
Fig. 7-6 Positive characteristic curve
Switching frequency f or
Pulse width v
Max.
Min.
Measured value
End value Start value
Fig. 7-7 Negative characteristic curve
130 ba76188d01 03/2017

DIQ/S 28X Outputs
Positive character- The proportional output range begins above the initial value. If the proportional
istic curve range is undercut or exceeded, the selected behavior comes into force.
Pulse width v [%]
100 90% 10%

90
Cycle
duration T
50% 50%
50
tOn tOf f
Proportional
band 10% 90%
10
0 Time
1 Measured value 2
Fig. 7-8 Pulse width output
Switching frequency f [1/min]
120
Maximum
switching frequency
60
50 % of maximum
Proportional switching frequency
band
Time
0
Minimum
1 Measured value 2 switching frequency
Fig. 7-9 Frequency output
1 Start value
2 End value
ba76188d01 03/2017 131

Outputs DIQ/S 28X
Negative charac- The proportional output range begins below the initial value. If the proportional
teristic curve range is undercut or exceeded, the selected behavior comes into force.
Pulse width v [%]
100 90% 10%

90
Cycle
duration T
50% 50%
50
tOn tOf f
Proportional
band 10% 90%
10
0 Time
2 Measured value 1
Fig. 7-10 Pulse width output
Switching frequency f [1/min]
100
Maximum
switching frequency
50
50 % of maximum
Proportional switching frequency
band
Time
0
Minumum
2 Measured value 1 switching frequency
Fig. 7-11 Frequency output
1 Start value
2 End value
132 ba76188d01 03/2017

DIQ/S 28X Outputs
7.3 Entering / editing the name of an output

For easier identification of the outputs, an individual name can be given to each
output in the Edit list of outputs overview.

The Edit list of outputs display opens.
3 Press <> to highlight a name in the Name column and confirm
with <OK>.
Fig. 7-12 Edit list of outputs
4 Select a letter, number or special character with <> and confirm

with <OK>.
5 Complete the name of the output and confirm with <OK>.
ba76188d01 03/2017 133

Outputs DIQ/S 28X
7.4 Linking the output with a sensor

settings -> Settings of outputs and links.
The Settings of outputs and links display opens.
3 Press <> to highlight the & column and confirm with <OK>.
4 Select an output with <> and confirm with <OK>. The Link
with... display opens.
The display shows a list of sensors that can be linked.
Fig. 7-13 Settings of outputs and links: Link with...
5 Using <>, select a sensor and confirm with <OK>.

The output is linked with the sensor.
In the overview Settings of outputs and links, field Ser. no., outputs
that are linked with sensors have the name of the linked sensor.
134 ba76188d01 03/2017

DIQ/S 28X Outputs
7.5 Deleting a link with an output

If a link between a current or relay output and a sensor is no longer required, you
can erase the link.

settings -> Settings of outputs and links.
3 Press <> to highlight the & column and confirm with <OK>.
4 Select a linked output with <> and confirm with <OK>.
Fig. 7-14 Settings of outputs and links: Erase link
5 Select and confirm Erase link with <> and <OK>.

A safety query appears.
6 Select and confirm Erase link with <> and <OK>.
The link is deleted.
ba76188d01 03/2017 135

Outputs DIQ/S 28X
7.6 Setting the relay outputs

3 Using <>, highlight the menu item, Settings of outputs and
links, and confirm with <OK>. The Settings of outputs and links display
appears.
4 Using <>, highlight the Feature column. Confirm with <OK>.
5 Using <>, highlight a line for a relay output (Rx) in the column
Feature. Confirm with <OK>.
6 Using <>, highlight the menu item, Relay function, and confirm
with <OK>.
Fig. 7-15 Settings of outputs and links
7 Using <>, select one of the functions listed below. Confirm with
<OK>.
136 ba76188d01 03/2017

DIQ/S 28X Outputs
Function Description
No function The relay output is not used.
System monitoring see section 7.6.2
Sensor monitoring see section 7.6.3
Limit indicator see section 7.6.4
Frequency controller see section 7.6.5
Pulse-width output see section 7.6.6
Cleaning see section 7.6.7
Sensor-controlled see section 7.6.8
Manual control see section 7.6.9
Alarm contact see section 7.6.10
8 Make the settings for the relay outputs with <> and <OK>.
The settings comprise the relay action (see section 7.6.1) and sensor
dependent settings.
9 Using <> and <OK>, highlight and confirm Save and quit.
The new settings are stored.
As soon as a function was selected for a relay output, you can select a relay
action (see section 7.6.1).
7.6.1 Relay action
The following actions of the relay can be defined in the Action setting:
Settings Explanations
Open The relay should open on every event.
Close The relay should close on every event.
Preferably set up the relay output as normally closed for monitoring

functions (ActionOpen ).
ba76188d01 03/2017 137

Outputs DIQ/S 28X
7.6.2 System monitoring
Function The System monitoring function enables the monitoring of system errors.
In order to set up the System monitoring function for a relay output, the relay
output must not be linked with a sensor (see section 7.4).
It can be used to monitor the following system errors.
Settings Settings Selection Explanations

Power failure On The Power failure On function monitors
Off the supply voltage in the IQ SENSORNET
at the DIQ/S 28X or the combination out-
put module. If the voltage falls below the
critical value, the relay switches.
Communication On The Communication On function moni-
Off tors the functioning of the DIQ/S 28X and
the communication with the combination
output module.
Collective On Collective error message On function
error message Off simultaneously monitors the proper func-
tioning of all sensors and the functioning
of the combination output module to be
monitored. (for details, see below this
table)
Action Open For all functions of the System monitor-
ing, the relay action is set to Open.
Collective error In the case of a Collective error message, the relay opens if one of the following
message malfunctions occurs:
 One of the sensors properly registered to the DIQ/S 28X does not provide a
valid main measured value
 One of the sensors properly registered to the DIQ/S 28X does not provide a
valid secondary measured value
 The monitoring output module has not received any new data DIQ/S 28X for
2 minutes.
In any case, the relay remains open for 10 seconds and only closes when the
malfunction is no longer present.
In the following cases, the relay does not open despite an invalid measured
value:
 The sensor is being calibrated
 The sensor is in the maintenance condition
 The sensor is being cleaned with the aid of a valve module in the system
(compressed air operated cleaning system).
138 ba76188d01 03/2017

DIQ/S 28X Outputs
7.6.3 Sensor monitoring
Function The Sensor monitoring function enables the monitoring of sensor errors and the
maintenance condition.
In order to set up the Sensor monitoring function for a relay output, the relay out-
put must be linked with a sensor (see section 7.4).
Settings Setting Selection Explanation

Errors Special Special sensor errors are monitored and
can prompt a relay action.
All All sensor errors (special ones and gen-
eral ones) are monitored and can prompt
a relay action.
Off Sensor errors are not monitored.
Mainten. Condition On Switching on and off the maintenance
Off condition (see section 7.10) is monitored
and can prompt a relay action.
Action Open Relay action (see section 7.6.1)
Close
Preferably set up the relay output for monitoring functions as an

opener (Action Open, see section 7.6.1).
Sensor messages include errors and information that are registered by the sen-
sor.
Special The special sensor errors are sensor-dependent. Details of this are given in the
sensor errors component operating manual of the respective sensor.
General Init This can prompt a relay action for a short time, depending on
Sensor errors the starting behavior of the system
---- Invalid measured value, or defective sensor
Error Communication with sensor interrupted
OFL Measuring range undercut or exceeded (overflow)
ba76188d01 03/2017 139

Outputs DIQ/S 28X
7.6.4 Limit indicator
Function The characteristic of the limit indicator is laid down in the Limit value UL, Limit
value LL, Hysteresis UL and Hysteresis LL settings. The fundamentals of the
function are described in the introductory chapter (see section 7.2.2).
In order to set up the Limit indicator function for a relay output, the relay output
must be linked with a sensor (see section 7.4).
Settings Setting Selection/Values Explanation

Limit values UL main variable Main variable designates the
LL main variable actual measured parameter of
the sensor (e.g. pH, oxygen,
UL adjoining var. etc.).
LL adjoining var. Adjoining variable designates
an additional measured
parameter (e.g. temperature).
Limit value UL Upper or lower limiting Minimum difference between
value the upper and lower limit
Limit value LL Any value within the value:
measuring range (sen- 5 % of the measuring range
sor-dependent)
Hysteresis UL 0 - 5% of the measur- Hysteresis for Limit value UL
ing range and Limit value LL.
Hysteresis LL
Behavior at error Open The relay opens, closes or
Close remains unchanged in the
Unchanged case of system errors or sen-
sor errors (see page 156).
Action Open Relay action (see
Close section 7.6.1)
Switching delay 0 ... 3600 s The time period for which a
limiting value must be
exceeded before the relay
operates.
Prevents frequent switching
for measured values that are
close to the limiting value.
7.6.5 Frequency controller
Function The characteristic of the frequency output is laid down in the Start value, End
value, Frequency (f) min. and Frequency (f) max. settings. The fundamentals of
the function are described in the introductory chapter (see section 7.2.3).
140 ba76188d01 03/2017

DIQ/S 28X Outputs
In order to set up the Frequency controller function for a relay output, the relay
output must be linked with a sensor (see section 7.4).

Measured variable Main variable Main variable designates the
Adjoining variable actual measured parameter
of the sensor (e.g. pH, oxy-
gen, etc.).
Adjoining variable desig-
nates an additional mea-
sured parameter (e.g.
temperature).
Start value within the measur- Minimum spacing:
ing range (sensor- 5 % of the measuring range
End value dependent)
Frequency (f) min. 0 to 120 1/min Minimum spacing:
10 1/min
Frequency (f) max.
Frequency with error 0 to 120 1/min In case of system errors or
sensor errors (see
page 156), the relay
switches with the frequency
specified.
Characteristic If a value for End value that is greater than the Start value is entered, the output
curve has a positive characteristic curve.
In order to obtain a negative characteristic curve, a value for End value must be
entered that is smaller than the value for Start value.
ba76188d01 03/2017 141

Outputs DIQ/S 28X
7.6.6 Pulse-width output
Function The characteristic of the pulse width output is laid down in the Start value, End
value, Pulse width (v) min. and Pulse width (v) max. settings. The fundamentals
of the function are described in the introductory chapter (see section 7.2.3).
In order to set up the Pulse-width output function for a relay output, the relay
output must be linked with a sensor (see section 7.4).

Adjoining variable actual measured parameter
of the sensor (e.g. pH, oxy-
gen, etc.).
Adjoining variable designates
parameter (e.g. tempera-
ture).
Start value within the measur- Minimum spacing:
ing range (sensor- 5 % of the measuring range
End value dependent)
Pulse width (v) min. 0 ... 100 % Minimum spacing:
10 % of the Cycle duration
Pulse width (v) max. (T)
Cycle duration (T) 5 ... 100 s Length of the switching
period T
T = (ton + toff)
Error pulse width 0 ... 100 % In case of system errors or
sensor errors (see
page 156), the relay switches
with the pulse-width speci-
fied.
Characteristic You can specify the minimum and maximum pulse width (v). This determines
curve the steepness of the characteristic curve of the output.
142 ba76188d01 03/2017

DIQ/S 28X Outputs
7.6.7 Cleaning
If the valve module MIQ/CHV PLUS is used, it is best to set the

Cleaning function directly at the valve output (V) of the MIQ/CHV
PLUS (see operating manual MIQ/CHV PLUS). The relay can be
used for other purposes.
Function The Cleaning function enables the time controlled automatic start of the sensor
cleaning function with the aid of a relay of the combination output module.
The relay controls the MIQ/CHV valve module and switches the compressed air
for the CH sensor cleaning head on or off.
In order to set up the Cleaning function for a relay output, the relay output must
be linked with a sensor (see section 7.4).
The relay of the combination output module assigned always works as a closer.
The cleaning cycle consists of Cleaning duration and Adjustment time.
During the cleaning cycle the Clean display flashes. The outputs linked with this
sensor are frozen. The maintenance condition (see section 7.10) is active.
After the Cleaning duration, the relay is opened. During the following Adjustment
time the outputs remain blocked.
The outputs linked with this sensor are only released when the cleaning cycle is
complete. The Clean display disappears. The maintenance condition is finished.
Testing the You can test the operativeness of the cleaning system as follows: Manually
operativeness open or close the relay with the Manual control function (see section 7.6.9) and,
while doing so, check the behavior of the cleaning system.
Alternatively, you can test the operativeness of the cleaning system by checking
the performance of the function at the start time set up (reference time ±
interval). To perform a test immediately, the reference time can be set so that
the next cleaning cycle will start in a few minutes (settings: see following table).

Reference time (h) 0 ... 23 h Time at which a cleaning cycle
is started. Further cleaning
Reference time 0 ... 60 min cycles will be performed at the
(min) times specified by the cleaning
interval.
Interval unit 1 .. 7 d Selection of range and unit for
1 .. 24 h the Reinigungsintervall.
5 .. 60 min
ba76188d01 03/2017 143

Outputs DIQ/S 28X
Setting Selection/Values Explanation

Cleaning interval 1/2/3/4/5/6/7 d Repeat interval for the clean-
ing function:
or: Time between the start time of
1/2/3/4/6/8/12/24 h a cleaning cycle and the start
time of the next cleaning
or: cycle*.
5/10/15/20/30/60 min
Cleaning duration 0 ... 300 s Duration of the cleaning
Adjustment time 0 ... 900 s Time extension to allow the
sensor to adjust to the test
sample after cleaning.
* With short cleaning intervals, the adjustable values for the Cleaning duration
and Adjustment time are limited. The following values apply:
Cleaning interval Cleaning duration Adjustment time

≤ 10 min max. 60 s max. 120 s
≤ 20 min max. 180 s max. 300 s
With this, the cleaning times are fixed. They only change when the
reference time is changed.
The reference time and all further cleaning times relate to the date
and time of the system clock. How to set the system clock is
described in the system operating manual.
Example Setting Result

Reference time (h): 12 Reference time: 12:00 hours
Reference time 0 This specifies the following start times:
(min): Hours (h) 04:00, 12:00 and 20:00 hours
Interval unit: 8h
Cleaning interval:
144 ba76188d01 03/2017

DIQ/S 28X Outputs
2
1
t1a t1b
relay 4 4
condition 1
t1 t1 t1
closed
open
t2 t2 t2 t2
00:00 04:00 12:00 20:00 24:00 Time
1 Reference time
Begin of a cleaning cycle (t1)
Begin of the specified Cleaning duration (t1a)
2 End of the specified Cleaning duration (t1a)
Begin of the specified Adjustment time (t1b)
3 End of the specified Adjustment time (t1b)
End of the cleaning cycle (t1)
4 Reference time ± Cleaning interval (t2)
Begin of a cleaning cycle
Canceling the A running cleaning cycle is canceled:

cleaning  Automatic
– if the sensor switches to the inactive condition during the cleaning cycle
 Manual
– By pressing the <C> key
– By switching on the maintenance condition
Each time the cleaning cycle is canceled, the relay opens immediately.
If the cleaning cycle is canceled automatically, the outputs linked to the sensor
are released immediately.
If the cleaning cycle is canceled manually, the sensor is in the maintenance
ba76188d01 03/2017 145

Outputs DIQ/S 28X
condition. The linked outputs are only released after the maintenance condition
was terminated manually.
The next cleaning cycle will be performed at the time set up.
In case of a power failure, all relays open. The cleaning cycle is

canceled. The outputs linked with the sensor change to the non-
active condition (see section 7.9.2). As soon as the power is avail-
able, the outputs are released again. The next cleaning cycle will be
performed at the time set up.
7.6.8 Sensor-controlled
With the Sensor-controlled function, the relay is controlled by a linked sensor.

Prerequisites  Sensor that sends signals to trigger a cleaning cycle, e.g. UV/VIS sensor

Pulse length Automatic The duration of the cleaning
procedure with air is pro-
grammed in the sensor.
The relay automatically takes
over from the sensor the
cleaning duration.
0,5 s The relay finishes the cleaning
1s procedure after the interval
2s selected here.
3s
Set up the cleaning process in the menu Settings of sensors and diff.
sensors of the relevant sensor.
146 ba76188d01 03/2017

DIQ/S 28X Outputs
7.6.9 Manual control
Function The Manual control function can be used to test the operativeness of an instru-
ment that is connected to the relay. To do so, close or open the relay manually
and, while doing so, check the behavior of the connected instrument.

Relay function Manual control The selected relay action is car-
ried out with Save and quit.
Close
The settings for other functions in the Relay function menu as, for
example, Frequency controller and Pulse-width output are retained
while the Manual control is carried out.
7.6.10 Alarm contact
Function The Alarm contact function triggers a relay action (opening or closing) if a
defined alarm event takes place. The Alarm contact function is only available for
relays that are not linked with a sensor. If necessary, an existing link must be
erased.

Relay function Alarm contact The selected relay action is car-
ried out with Save and quit.
Close
7.7 Setting the current outputs (variant -CR3, CR6)

3 Using <>, highlight the menu item, Settings of outputs and
links, and confirm with <OK>. The Settings of outputs and links display
appears.
4 Using <>, highlight the Feature column. Confirm with <OK>.
ba76188d01 03/2017 147

Outputs DIQ/S 28X
5 Using <>, highlight a line for a current output (Cx) in the column
Feature. Confirm with <OK>.
6 Using <>, highlight the menu item, Current output, and confirm
with <OK>.
Fig. 7-16 Settings of outputs and links
7 Select and confirm a function with <> and <OK>.
Function Settings
No function The current output is not used.
Recorder see section 7.7.1
PID controller see section 7.7.2
Fixed current value see section 7.7.3
8 Make the settings for the current output with <> and <OK>.
9 Using <> and <OK>, highlight and confirm Save and quit.
The new settings are stored.
7.7.1 Recorder
Function The measured values of the linked sensor at the current output are set up as cur-
rent intensity in the Recorder application. The output of measured values is laid
down in the Recorder type, Start value and End value settings.
148 ba76188d01 03/2017

DIQ/S 28X Outputs

Recorder type 0 to 20 mA or
4 to 20 mA
Start value (sensor depen- Minimum spacing:
dent) ≤ 5 % of the measuring range
End value (sensor-dependent)
Adjoining variable actual measured parameter of
etc.).
Adjoining variable designates an
additional measured parameter
(e.g. temperature).
Attenuation 0 ... 40 mA/s Speed of change of the output
current (mA/s) in the case of
erratic changes of the input sig-
nal.
I -> UFL/OFL Error Current values outside the range
between Start value and End
value are regarded as an error.
The current output reacts as
specified under Behavior at error
(see below).
Limitation The current at the output is lim-
ited to the Start value or End
value.
Behavior at error Fixed current In the case of system errors and
value sensor errors, the current output
delivers the fixed current value
that was specified.
Possible values:
0 ... 21 mA.
Unchanged The current at the output remains
unchanged.
7.7.2 PID controller
Function The PID controller function can use an output as a controller output. The regu-
lator can be configured as a Proportional regulator with switchable Integral and
Differential regulator parts (PID Controller).
The control response of the PID controller is described by the following formula:
ba76188d01 03/2017 149

Outputs DIQ/S 28X
 1 dx 
I Controller = I 0 + K  xe +  xe dt + Td e 
 Ti dt 
with:
I max − I min
K=
Xp
xe = xnom − xactual
I min ≤ I Controller ≤ I max
IController Current on the controller output at time t

I0 Current on the output if xactual = xset
K Amplification
Xp Proportional range
xe Control difference
xactual Actual value (current measured value)
xset Set value
ti Integral algorithm
td Differential control part
t Time
Imin Lower current limitation
Imax Upper current limitation
The adjustable control parameters are xset, I0, Xp, Imin, Imax, ti and td (see setting
table on page 153).
By activating or deactivating the Integral (ti) and Differential (td) controller part,
the following controller types can be configured:
Regulator type td [s] ti [s]

P controller 0 0
PI controller 0 1 to 9999
150 ba76188d01 03/2017

DIQ/S 28X Outputs
Regulator type td [s] ti [s]

PD controller 1 to 9999 0
PID controller 1 to 9999 1 to 9999
Characteristic For a pure P controller the correlation between the measured value and current
curve of the I on the controller output results in the following characteristic curve:
proportional
controller
Fig. 7-17 Proportional controller (negative characteristic curve)
The proportional range Xp is limited by the measurement range of the linked

sensor. If a value is entered for the parameter Xp that is greater than zero, the
controller has a positive characteristic curve (example Fig. 7-17). To obtain a
positive characteristic curve, a negative value must be entered for Xp.
ba76188d01 03/2017 151

Outputs DIQ/S 28X
Application exam-  Regulation of the oxygen concentration

ple
 Sensor: TriOxmatic 700 IQ (measuring range: 0 to 60 mg/l)
Control parameter Value

Nominal value 4 mg/l
Xp 10 % of the measuring range
or 6 mg/l
Imin 8 mA
Imax 14 mA
Io 12 mA
ti 0 s (no I algorithm)
td 0 s (no D algorithm)
The control parameters result in the following (negative) characteristic curve:
Current I [mA]
Xp
Imax 14
Io 12
Imin 8
0
2 4 8 Measured value [mg/l]
Nominal value
Fig. 7-18 Characteristic curve for application example
The controller works with the following amplification:
152 ba76188d01 03/2017

DIQ/S 28X Outputs
6 mA mA
K = =1
6 mg/l mg/l
Within the proportional range an increase of the concentration by 1 mg/l
causes a reduction of the output current by 1 mA. If the measured con-
centration is 5 mg/l, for example, 11 mA is output:
mA
I Controller = 12 mA + 1 ⋅ (4 mg/l − 5 mg/l)
mg/l
mA
I Regler = 12 mA + 1 ⋅ (− 1 mg/l) = 11 mA
mg/l
The highest concentration at which the controller still works in the propor-
tional range is 8 mg/l (corresponding to Imin = 8 mA) and the lowest is
2 mg/l (corresponding to Imax = 14 mA).

Adjoining variable actual measured parameter of
etc.).
Adjoining variable designates
parameter (e.g. temperature).
Nominal value within the measuring Nominal value the measured
range (sensor- value is regulated to
dependent)
Xp 5 ... 100 % Proportional range of the con-
-5 ... -100 % troller.
% of the measuring
range Negative values result in a
positive characteristic curve.
Imin 0 ... 20 mA Lower current limitation *
Imax 0 ... 20 mA Upper current limitation *
* Note:
Spacing between Imin and
Imax:
at least 5 mA
ba76188d01 03/2017 153

Outputs DIQ/S 28X

Io 0 ... 20 mA Current value on the output if
the measured value equals the
Nominal value
ti 0 ... 9999 s Hold-back time:
Integral part of the controller
(0 = not effective)
td 0 ... 9999 s Reset time:
Differential part of the control-
ler
(0 = not effective)
Behavior at error Fixed current value In the case of an error, the cur-
rent output supplies the cur-
rent value defined in the
Current with error field (any in
the range
0 ... 21 mA).
Unchanged In the case of an error, the cur-
rent on the output remains
unchanged.
7.7.3 Fixed current value
Function The Fixed current value function can be used to test the operativeness of the
instruments connected to the outputs: output different current values to the out-
put and, while doing so, check the behavior of the connected instrument.

Current output Fixed current Using Save and quit, the nominal
value amperage that was input as Inom
is output.
Inom 0 ... 20 mA The nominal amperage that is
output.
The settings for other functions in the Current output menu as, for
example, PID controller and Recorder are retained while the Fixed
current value is carried out.
154 ba76188d01 03/2017

DIQ/S 28X Outputs
7.8 Checking the condition of the outputs

This function provides a simple overview of the conditions of all outputs of the
combination output module.
For the relays, the displayed condition is open or closed.
For the current outputs, the current value present at the outputs is displayed.

3 Using <>, highlight the menu item, Service, and confirm with
<OK>. The Service dialog window opens.
4 Using <>, highlight the menu item, List of all components, and
confirm with <OK>.
The List of all components dialog window opens.
5 Highlight the required component with <> (column Model, entry
MIQCR3) and confirm with <OK>.
The Status of output channels window opens.
Fig. 7-19 Status of output channels
6 Using <M> or e, exit the window Status of output channels.
ba76188d01 03/2017 155

Outputs DIQ/S 28X
7.9 Behavior of linked outputs
7.9.1 Behavior in case of error
For linked relay outputs or current outputs, you can determine the behavior of
the outputs in case of errors.
Depending on the use of the output, the behavior in case of errors is set in the
following menus:
Output Menu
Frequency controller Frequency with error (see section 7.6.5)
Pulse-width output Error pulse width (see section 7.6.6)
Recorder Current with error (see section 7.7.1)
Error events The specified behavior occurs with the following events or conditions:
 The linked sensor does not provide any valid measured value
(display of Init, Error, "-----", or OFL)
 Communication with the DIQ/S 28X is interrupted for more than 2 minutes.
 The supply voltage for the DIQ/S 28X is too low.
 In the function Recorder, the measured value of the linked sensor is outside
the range between Start value and End value.
Freezing the Irrespective of the behavior in case of error that was defined, the following situ-
conditions of the ations cause the conditions of the outputs to be frozen:
outputs  The linked sensor is in the maintenance condition
(display of Cal, Clean, or flashing measured value).
 Communication with the DIQ/S 28X is temporarily interrupted. After an inter-
ruption of 2 minutes the output changes to the behavior defined for error.
Restoring the The relay or current output automatically returns to its normal condition as soon
normal functioning as all errors have been eliminated and all conditions that caused the freezing of
the outputs were eliminated.
156 ba76188d01 03/2017

DIQ/S 28X Outputs
7.9.2 Behavior in non-operative condition
An output is non-operative when no function is activated for the output.

An output becomes non-operative in case of
 Power failure
(As soon as the supply voltage is sufficient again, the non-operative condition
of the outputs ends. The outputs function as specified by the user again.)
 Erasing a link to a sensor
 Changing the Measuring mode sensor setting for a linked sensor
 Changing the Measuring range sensor setting for a linked sensor
Before editing sensor settings a note appears on the display to

inform you that links will be erased when you change the Measuring
mode or Measuring range sensor setting.
Settings in the Current output Relay output

non-active
condition Current: 0 A Relay: Open
7.10 Maintenance condition of the sensors

The maintenance condition of the sensors is used for calibrating, cleaning, ser-
vicing and repairing (removing and exchanging) the sensors.
In the maintenance condition
 the system does not react to the current measured value or the condition of
the selected sensor
 linked outputs are frozen
 sensor errors do not prompt changes in the conditions of linked outputs.
The maintenance condition is automatically activated

 during calibration. After calibration the sensor remains in the maintenance
condition until the maintenance condition is switched off manually (see
section 7.10.2)
 during the cleaning cycle (see section 7.6.7)
If you want to clean, service or repair (remove and exchange) a sensor, switch
on the maintenance condition manually (see section 7.10.1).
When you have finished cleaning, servicing or repairing the sensor, switch off
the maintenance condition manually (see section 7.10.2).
ba76188d01 03/2017 157

Outputs DIQ/S 28X
If the maintenance condition is activated for a sensor, the measured

values or status indicators of this sensor flash in the measured value
display.
7.10.1 Switching on the maintenance condition

2 Select the sensor you want to switch on the maintenance condition for
with <>. The measured values of the sensor do not flash.
4 Using <>, highlight the menu item Switch maintenance condi-
tion on/off or Maintenance Sensor S0x and confirm with <OK>. A win-
dow that informs you about the maintenance condition opens up.
5 Confirm Continue with <OK>.
The selected sensor is in the maintenance condition. Linked outputs are
frozen.
The measured values of the sensor flash.
7.10.2 Switching off the maintenance condition

2 Select the sensor you want to switch off the maintenance condition for
with <>. The measured values of the sensor flash.
4 Using <>, highlight the menu item Switch maintenance condi-
tion on/off or Maintenance Sensor S0x and confirm with <OK>. A win-
dow that informs you about the maintenance condition opens up.
5 Confirm Continue with <OK>.
The maintenance condition of the selected sensor is switched off.
Linked outputs are released.
The measured values of the sensor do not flash.
158 ba76188d01 03/2017

DIQ/S 28X Maintenance and cleaning
8 Maintenance and cleaning

8.1 Maintenance
Maintenance Component Maintenance

activities
IQ sensors Depending on the type of sensor
(see the component operating manual of the sen-
sor)
IQ SENSORNET, No maintenance required
DIQ modules,
MIQ modules
8.2 Cleaning
IQ SENSORNET, Clean components mounted in the open of gross contamination as necessary.
DIQ modules, We recommend cleaning the worst of the dirt on the enclosure and the area
MIQ modules directly around it each time before opening in order to prevent contamination
from entering the open enclosure.
To clean the module, wipe the enclosure surfaces with a damp, lint-free cloth. If
compressed air is available on site, blow off the worst of the dirt beforehand.
Keep the enclosure closed while doing so.
NOTE
Do not use high-pressure water blasters for cleaning (danger of water penetra-
tion!). Also do not use aggressive cleaning agents such as alcohol, organic sol-
vents or chemical detergents. These types of cleaning agent can attack the
surface of the enclosure.
The enclosure and the window of the display are made of plastic.
Thus, avoid contact with acetone and similar detergents.
Remove any splashes immediately.
IQ sensors The cleaning of the IQ sensors depends greatly on the respective application.
Instructions for this are given in the respective component operating manual.
A valve module for the compressed air-operated cleaning of sensors is available
as an accessory.
ba76188d01 03/2017 159

What to do if ... DIQ/S 28X
9 What to do if ...
9.1 Information on errors
Log book The IQ SENSORNET system performs a comprehensive cyclical self test during
operation. While doing so, the system identifies all states that deviate from
normal operation and enters corresponding messages in the log book (informa-
tion or error message).
With the aid of the log book, you can call up instructions on how to clear the error
directly on the Universal Transmitter. The log book is described in detail in
section 4.5 MESSAGES AND LOG BOOK.
Information on possible errors in IQ sensors and MIQ output

modules is given in the chapter WHAT TO DO IF ... of the respective
component operating manual.
9.2 Errors: causes and elimination
The system no Cause Remedy

longer reacts to
entries – System error Reset the system:
– Switch off the power supply and
switch it on again after 10 s
"Error" in the Cause Remedy

measured value
display – Communication with the – Check the cable connection
IQ Sensor interrupted
– Error in the IQ sensor – Disconnect the IQ sensor and recon-
nect it after 10 s
The selected Cause Remedy

system language
was not activated – A system language was selected – Contact the service department,
for all components that is not available in at least as a software update is required for
one component (sensor, Univer- the relevant components.
sal Transmitter, output module).
The standard language, English,
was activated instead of the
selected system language.
160 ba76188d01 03/2017

DIQ/S 28X What to do if ...
9.3 Replacing system components
It is always possible to replace components and assign a substitute

if the software state of the substitute component is as high as or
higher than the software version of the original component.
9.3.1 Replacing passive components
Passive components include all components that the Universal Transmitter can-
not recognize.
These include:
 MIQ/PS (power supply module)
 DIQ/JB (branching module)
 DIQ/CHV (module for automatic compressed air cleaning)
 Cables (SNCIQ, SACIQ).
WARNING
If the MIQ/PS power supply module is opened during op-
eration, there is a danger to life due to possible hazard of
electric shock. The MIQ/PS may only be opened when the
line voltage is switched off. Secure the line voltage
against being switched on again.
Only ever replace components when the IQ SENSORNET
system is switched off. Defective components are re-
moved in the reverse order to the installation (see
chapter 3 INSTALLATION).
9.3.2 Adding and replacing IQ sensors
Inactive datasets If an IQ sensor is removed from the system, its settings remain stored in the Uni-
of IQ sensors versal Transmitter. A "?" appears in the left column of the Edit list of sensors
menu. This indicates an "inactive dataset". A dataset contains the following
information:
 Serial number of the IQ sensor (and, with it, the type of sensor)
 Display position
 All sensor settings
 All characteristics of the link with an output.
If no suitable inactive dataset is available, a newly connected IQ sensor is auto-

matically recognized as a new module and added to the list of sensors.
ba76188d01 03/2017 161

The maximum number of datasets (active and inactive datasets) for

IQ sensors is limited to 2 in the IQ SENSORNET system DIQ/S 284,
to 4 in the IQ SENSORNET system DIQ/S 282.
When this number is reached, no further IQ sensor can be installed.

If necessary, an inactive dataset has to be erased to make an exten-
sion possible.
The current calibration data of the IQ sensor is always stored in the

sensor. If an IQ sensor is connected that is ready for operation and
calibrated, this can be used immediately without the need for recal-
ibration.
To erase inactive datasets, see section 5.4.3.
If an IQ sensor is connected to the system when an inactive dataset is present,

the following cases are possible:
Case 1:
The serial number of the IQ sensor The connected IQ sensor is automat-
is identical with the serial number of ically assigned to the inactive dataset
an inactive dataset. and starts to operate again.
Example: Maintenance or repair.
This mechanism ensures that all

IQ sensors retain their settings and
links if an IQ sensor was removed for
maintenance, or if the system was
temporarily switched off.
162 ba76188d01 03/2017

Case 2:
The type of sensor is identical with Operator intervention is required here.
the type of sensor in an inactive The connected IQ sensor can:
dataset (or several inactive datas- – be assigned to the inactive dataset
ets), but the serial numbers differ. (or one of the inactive datasets).
Example: Replacing an IQ sensor.
Make sure that the substitute sen-
sor has at least the software status
of the active IQ sensor.
– be included as a new module in the
list of the sensors.
The operating sequence to do this is
described below.
Operating
1 Connect a new IQ sensor.
sequence in case 2
2 Switch to the measured value display with <M>. The component data-
base is updated. The following display appears (example):
Fig. 9-1 510 - Add/replace sensor
3 Select the required option with <> and confirm with <OK>.
– If Add new sensor was selected, the system changes directly to the
measured value display. As soon as the IQ sensor is ready for oper-
ation, it delivers a measured value.
– If Assign sensor as a substitute was selected, a list of matching inac-
tive datasets appears:
ba76188d01 03/2017 163

Fig. 9-2 520 - Assign sensor as a substitute
4 Select the required inactive dataset with <> and confirm with
<OK>. The system changes to the measured value display. The
IQ sensor takes over all settings of the inactive dataset. As soon as the
IQ sensor is ready for operation, it delivers a measured value.
9.3.3 Adding and replacing DIQ or MIQ output modules
WARNING
There is also a danger to life from voltages that may pres-
ent a hazard of electric shock on the relay contacts of
open DIQ or MIQ output modules (e.g. DIQ/CR3 or MIQ/
CR3). Output modules with relays may only be opened if
all external voltages have previously been switched off.
Secure all external voltages against being switched on
again for the duration of the work.
When replacing DIQ or MIQ modules make sure that the substitute
module has at least the software status of the active module.
Only replace any DIQ or MIQ output modules (all DIQ or MIQ modules with relay
contacts and/or electrical signal outputs) while the DIQ/S 28X system is
switched off. Defective DIQ or MIQ output modules are removed in the reverse
order to that of the installation. The installation is described in the INSTALLATION
chapter of the respective component operating manual.
164 ba76188d01 03/2017

Inactive datasets If an DIQ or MIQ output module is removed from the system, its settings remain
in MIQ output stored in the Universal Transmitter. A "?" appears in the left column (= inactive
modules dataset) of the Edit list of outputs menu. The dataset contains the following infor-
mation:
 All settings of the relays
 All settings of the current outputs.
If no inactive dataset is available, a newly connected MIQ output module is auto-

matically recognized as a new module and added to the list of outputs.
The maximum number of data sets (active and inactive datasets) for
DIQ or MIQ output modules is limited to 2 in the IQ SENSORNET sys-
tem DIQ/S 28X. When this number is reached, no further DIQ or
MIQ output module can be installed. If necessary, an inactive data-
set has to be erased to make an extension possible.
To erase inactive datasets, see section 5.7.2.
If a DIQ or MIQ output module is connected to the system when an inactive data-
set is present, the following cases are possible:
Case 1:
The serial number of the DIQ or The connected DIQ or MIQ output
MIQ output module is identical with module is automatically assigned to
the serial number in an inactive the inactive dataset and start operat-
dataset. ing again.
Example: In the case of repair.
Case 2:
The type of the DIQ or MIQ output Operator intervention is required
module is identical with the type of here. The connected DIQ or
an inactive dataset (or several inac- MIQ output module can:
tive datasets), but the serial num- – be assigned to the inactive dataset
bers differ. (or one of the inactive datasets).
Example: Replacing a DIQ or
MIQ output module.
– be included as a new module in
the list of outputs.
The operating sequence to do this is
described below.
ba76188d01 03/2017 165

Operating
1 Remove the (defective) DIQ or MIQ output module. The output module
sequence in case 2
is removed in the reverse order to the installation. The installation is
described in the INSTALLATION chapter of the respective component
operating manual.
2 Install the new DIQ or MIQ output module (INSTALLATION chapter of the
respective component operating manual).
3 Switch to the measured value display with <M>. The component data-
base is updated. The following display appears (example):
Fig. 9-3 410 - Add/replace output module
4 Select the required option with <> and confirm with <OK>.
– If Add new output module was selected, the system changes directly
to the measured value display.
– If Assign output module as a substitute was selected, a list of the
matching inactive datasets appears:
166 ba76188d01 03/2017

Fig. 9-4 420 - Assign output module as a substitute
5 Select the required inactive dataset with <> and confirm with
<OK>. The system changes to the measured value display. The
MIQ output module takes over all settings of the inactive dataset.
ba76188d01 03/2017 167

Technical data DIQ/S 28X
10 Technical data
10.1 DIQ/S 282, DIQ/S 284
Dimensions Front view: Side view:

DIQ/S 28X-CRx 144,0 68,0 52,2
144,0
M C S
DIQ/S 284 ESC OK

USB
11,0
Rear view: 16,5
115.0
70.0
45.0
72.0
137.0
Stack mounting:
48 48
137.0
Fig. 10-1 Dimension drawing of the DIQ/S 28X (dimensions in mm)
168 ba76188d01 03/2017

DIQ/S 28X Technical data
Dimensions Front view Side

DIQ/S 28X-MOD 144,0 view: 68,0 52,2
DIQ/S 28X-PR
144,0
M C S
DIQ/S 284 ESC OK

USB
21,0
11,0
Rear view 16,5

115,0
70,0 45,0
72,0
137,0
Stack mounting
48 48
137,0
Fig. 10-2 Dimension drawing DIQ/S 28X-MOD, DIQ/S 28X-PR (dimensions in mm)
ba76188d01 03/2017 169

Dimensions Front view Side

144,0 view 68,0 52,2
DIQ/S 28X
[-CRx]-E[F]
144,0
M C S
DIQ/S 284 ESC OK

USB
28,0
11,0
Rear view 16,5

115,0
70,0
45,0
72,0
137,0
Stack mounting
48 48
137,0
Fig. 10-3 Dimension drawing of the DIQ/S 284E[F] (dimensions in mm)
Mechanical Maximum number of 3

structure MIQ modules in a mod-
ule stack
Enclosure material Polycarbonate with 20 % glass fiber
Weight Approx. 1.2 kg
Approx. 1.7 kg (Variant DIQ/S 284-CR6[-E])
170 ba76188d01 03/2017

Type of protection IP 67
(not suitable for direct conduit connection).
Conduits have to be connected with CC-Box flexible

adapters, or with CC-PM adapters (see
chapter 11 ACCESSORIES AND OPTIONS)
Test certificates cETLus, CE
Ambient Temperature
conditions
Mounting/installation/ + 5 °C ... + 40 °C (+ 41 ... +104 °F)
maintenance
Operation - 20 °C ... + 55 °C (- 4 ... + 131 °F)
Storage - 25 °C ... + 65 °C (- 13 ... + 149 °F)
Relative humidity
Mounting/installation/ ≤ 80 %
maintenance
Yearly average ≤ 90 %
Dew formation Possible
Site altitude Max. 2000 m above sea level
Electrical data Power supply Nominal voltage: 100 ... 240 VAC ± 10 %
DIQ/S 28X
(240 V AC/DC line Frequency: 50/60 Hz
power version) according to DIN IEC 60038
Line power connection: 2 pin, N and L
Line cross-section of mains connection:

Europe: 1.5 ... 4.0 mm2
USA: AWG 14 ... 12
Fuse rating on the operator side: max. 16 A

Protective class II
ba76188d01 03/2017 171

Overvoltage II
category
Power consumption max. approx. 20 W
Electrical data Supply Nominal voltage: 24 V AC/DC ± 10 %

DIQ/S 28X[-XX]/ protective low voltage
24V SELV (Safety
(24 V AC/DC Extra Low Voltage)
version)
AC frequency:50/60 Hz according to
DIN IEC 60038
Connection:2 pin
Line cross-section of connections:

Europe: 1.5 ... 4.0 mm2
USA: AWG 14 ... 12
Fuse rating on the operator side: max. 16 A
Switch-on current:
1.5 A AC/DC (100 ms)
Power consumption max. approx. 20 W
Electrical The electrical connections are inside the housing.

connections
Assignment of the terminal strips: See section 3.13.
DIQ/S 28X[-...]
Relay Output Galvanically separated

(3 x)
Max. switching voltage 240 VAC or 24 VDC
Max. switching current 2 A (AC and DC)
Installation require- Fuse rating on the operator side: max. 2 A
ments
Relay functions Programmable as:
– Opener or closer
– Limit monitor
– Monitoring of the warning and error signals of the
IQ SENSORNET
– Proportional frequency output
– Proportional pulse width output
172 ba76188d01 03/2017

Current outputs Output Galvanically separated from the sensors

(DIQ/S 28X-CRx)
Output current Can be switched between 0 - 20 mA and
4 - 20 mA
In the case of errors, can be set to: 0 ... 21 mA
Max. initial output volt- 13 V, in the case of missing or incorrect burden
age
Accuracy 0.3 % of current value ± 50 µA,
load max. 500 Ω
Functions Programmable:
– Recorder attenuation, adjustable
0 - 40 mA/s
– Error behavior can be set as required
0 ... 21 mA
– Error behavior according to Namur NE43 can be
selected
– Positive and negative characteristic curve
– PID controller
Connecting Terminal type Screw-type terminal strip, accessible by raising the

terminals lid
Terminal ranges Solid wires: 0.2 ... 4.0 mm2
AWG 24 ... 12
Flexible wires: 0.2 ... 2.5 mm2
Cable glands Suitable for cable diam- 4.5 ... 10 mm or 7 ... 13 mm

eter
EMC product and EN 61326 EMC requirements for electrical resources for con-
system character- trol technology and laboratory use
istics
– Resources for industrial areas, intended for indis-
pensable operation
– Interference emission limits for resources of class
A
System lightning pro- Extended protective characteristics as opposed to
tection EN 61326
FCC, class A
ba76188d01 03/2017 173

Any combination of the IQ SENSORNET with IQ SENSOR NET prod-

ucts in a user-specific system achieves the listed EMC characteris-
tics.
Meter safety Applicable norms – EN 61010-1

– UL 61010-1
– CAN/CSA C22.2#61010-1
USB-A interface Version USB 2.0

Usage Download of measurement data, software updates,
electronic key
Immediately close the USB connection with the protective cover

when you have removed the USB device.
When the USB connection is open, there is a danger of corrosion.
Ethernet RJ45 socket (can be retrofitted as a climate resistant RJ45 socket for operation
connection at an open-air test site section 11).
(DIQ/S 28X-E[F])
Fieldbus DIQ/S 28X variant Fieldbus connection

connection
DIQ/S 28X[-CRx][-E] no connection to fieldbus
DIQ/S 28XPR PROFIBUS DP (RS 485)*
DIQ/S 28X-MOD Modbus RTU (RS 485)*
DIQ/S 28X[-CRx]-EF Ethernet fieldbuses
(EtherNet/IP™, Profinet, Modbus TCP)
* Connection via 9-pin D-SUB socket on the underside of the housing, compatible
with Phoenix connector (IP67).
174 ba76188d01 03/2017

10.2 General data of MIQ modules
Technical data on special MIQ modules are given in the respective

operating manuals.
Dimensions 144.0 52.2
Front view: Side view:
144,0
115.0 11.0
70.0
16.5
Rear view:
45.0
72.0
Stack mounting: 100 148
Fig. 10-4 Dimension drawing of MIQ module (dimensions in mm)
ba76188d01 03/2017 175

Mechanical Maximum number of 3

structure MIQ modules in a mod-
ule stack
Enclosure material Polycarbonate with 20 % glass fiber

Terminal SENSORNET connec- At least two in each DIQ or MIQ module.

connections tions Additional connectable SENSORNET terminator
(terminating resistor)
Further connections Module-dependent
Terminal type Screw-type terminal strip, accessible by raising the
lid
AWG 24 ... 12
Cable feeds 4 cable glands M16 x 1.5 on the underside of the
module
Cable glands Suitable for cable 4.5 - 10 mm or

sheath diameter
9.0 - 13 mm
176 ba76188d01 03/2017

10.3 DIQ/JB
Dimensions 94 57
DIQ/JB
94
ca. 25
Fig. 10-5 Dimension drawing of DIQ/JB (dimensions in mm)
Mechanical Enclosure material Polystyrene

structure


1 2 3 4 5 6 7
Electrical (7 passive, potential free terminals for
connections line extension or branching)
1 2 3 4 5 6 7
Connecting Terminal type Screw-type terminal strip

terminals
ba76188d01 03/2017 177


AWG 24 ... 12
Cable feeds Prepared openings for installing two screwed cable
glands M16 x 1.5 both on the upper and underside
10.4 DIQ/CHV
Dimensions 94 57
DIQ/CHV
94
28
Fig. 10-6 Dimension drawing of DIQ/CHV (dimensions in mm)
Mechanical Enclosure material Polystyrene

structure

Electrical  1 x valve switching contact

connections
 4 x potential-free terminals to connect interface lines
Terminal strip inside the enclosure:
(HILFLSKONTAKTE) VENTIL
(AUXILIARY) VALVE
X6 X5 X4 X3 X2 X1
178 ba76188d01 03/2017

Connecting Terminal type Screw-type terminal strip

terminals
AWG 24 ... 12
Cable feeds Prepared openings for installing two screwed cable
glands M16 x 1.5 on the upper side
Valve circuits Switching voltage Approx. 22 V

Max. switching current Approx. 40 mA
NOTE
The valve may only be operated with the auxiliary voltage of the DIQ/S 28X Uni-
versal Transmitter.
Compressed air Required air quality Dry, free of dust and oil
Operating pressure Max. 7x105 Pa (7 bar) absolute
Connections on the DIQ/CHV 6 mm hose nozzles
10.5 Space required by mounted components
Wall mounting and

Wall mounting
top hat rail or
mounting top hat rail mounting
Space required
195
290
for screwdriver
48
340
Fig. 10-7 Space required for wall and top hat rail mounting: (dimensions in mm)
ba76188d01 03/2017 179

Panel mounting 48 5
Panel mounting
(PMS/IQ)
215
185
Space required
for screwdriver 105
Fig. 10-8 Space required for panel mounting (PMS/IQ) (dimensions in mm)
Information on the space required with the PMS/IQ-X mounting set:

see PMS/IQ-X operating manual.
180 ba76188d01 03/2017

DIQ/S 28X Accessories and options
11 Accessories and options
Description Model Order no.

IQ SENSORNET cable - please specify required length in m SNCIQ 480046Y
when ordering SNCIQ/UG 480047Y
IQ sensor connection cable
1.5 m SACIQ-1.5 480040Y
7.0 m SACIQ-7.0 480042Y
15.0 m SACIQ-15.0 480044Y
Special length up to max. 100 m SACIQ-SO 480041VY
20 m (seawater version) SACIQ-20.0 SW 480045Y
Special length (seawater version) SACIQ-SO SW 480064VY
Set of 4 cable glands M20 for cable sheaths with an outer diam- EW/1 480051Y
eter greater than 10 mm
Branching module DIQ/JB 472005Y
Valve module DIQ/CHV 472007Y
Sun shield for a unit of up to two stacked MIQ modules plus SSH/IQ 109295Y
docked Universal Transmitter
Sun shield for a single MIQ module plus docked Universal SD/K 170 109284Y
Transmitter
Mounting kit for fixing the SD/K 170 sun shield on horizontal or MR/SD 170 109286Y
vertical pipes
Kit for wall mounting of a MIQ module WMS/IQ 480052Y
Set for panel mounting of MIQ modules PMS/IQ 480048Y
Set for panel mounting of the DIQ/S 28X [-MOD], [-PR], [-E(F)]. PMS/IQ-X 480049Y
The interface (MOD, PR, E, EF) is mounted behind the panel.
Kit for mounting of MIQ modules on a 35 mm top hat rail in THS/IQ 480050Y
accordance with EN 50022
Adapter to protect the RJ45 interface against moisture ADA/E 902890Y
Flexible conduit adapter for IQ SENSORNET components CC-Box 900120Y
Flexible conduit adapter for fieldbus plugs CC-PM 900125Y
ba76188d01 03/2017 181

Messages DIQ/S 28X
12 Messages
12.1 Explanation of the message codes
The log book contains a list with all the messages from all modules. Each
message consists of message code, date and time. You can obtain more
detailed information by opening the full message text (see section 4.5).
The full message text comes from the component that has triggered the
message. Therefore, these texts are only available from components which are
connected to the system and ready for operation.
If a message text is not available, because the component is not connected to
the system, you can look up the texts of the messages in the operating manual
of the respective component.
The following lists contain the message codes and the related message texts
that are shown on the display. Error messages and info messages are listed
separately.
General explanations on the subjects of messages, message codes and log
book are given in section 4.5 of this system operating manual.
Module code Component

171 DIQ/S 282
172 DIQ/S 284
12.1.1 Error messages
Message code Message text

EI4171 Max. components of this component type exceeded
EI4172 Danger of system overload
* Check and adapt the components for this type
EI5171 Component cannot be reached or not present
EI5172 * Component has been removed from the system, insert component
again
* Connex. to component cut.,
Check sys. installation acc. to op. manual
EI6171 Incompatible terminal software
EI6172 * Contact service
EI7171 Incompatible controller software
EI7172 * Contact service
182 ba76188d01 03/2017

DIQ/S 28X Messages

EI8171 Connection to the component instable
EI8172 * Check installation and cable lengths,
Follow installation instructions
* Set SN terminator switch acc. to operating manual
* Check environmental effects
* Component defective, contact service
EI9171 Power failure occurred
EI9172 * Check date and time and, if necessary, adjust them
EA8171 Error at automatic air pressure measurement
EA8172 An air pressure value of 1013 mbar is used for air pressure compen-
sation
* Contact service
12.1.2 Informative messages

II1171 Language not available,
II1172 Default language German
* Contact service
II2171 New IQ Sensor Net component identified
II2172
II3171 New IQ Sensor Net component recorded
II3172 * See component lists
II4171 IQ Sensor Net component recorded as replacement component
II4172 * See component lists
II5171 Link sensor - output has been erased
II5172 * if necessary, link sensor again
II9171 Date and time have been set
II9172
ba76188d01 03/2017 183

Messages DIQ/S 28X
184 ba76188d01 03/2017

IQ SENSORNET Index
13 Index
A External voltages ......................................164
Access control ............................................ 81
Air pressure .............................................. 104 F
Ambient conditions ................................... 171 Fieldbus ....................................................120
Arrow keys 57, 125, 128, 134, 137, 139, 143, Function code ...........................................108
144, .......................... 146, 147, 154, 157, 158
Auxiliary voltage
I
Terminal strip ....................................... 53
Usage ................................................... 46 Inactive dataset
Output module ..............................96, 165
Sensors .........................................88, 161
B Information ..................................................67
Bus interfaces .......................................... 108 Initialization .................................................48
IQ Web Connect .......................................116
C
Calibration data .......................................... 72 K
Calibration history ...................................... 72 Keys ............................................................57
Cleaning
of module enclosures ......................... 159
L
Current outputs
Terminal strip ....................................... 53 Language ....................................................80
Lightning protection
External protective measures ...............19
D Installation guidelines ...........................19
Daily load diagram of selected sensor ....... 64 Internal protective measures ................19
Data transmission ...................................... 66 Line power connection
Dimensions 24 V version ..........................................41
DIQ/S 182 .................................. 169, 170 Line power version ................................38
DIQ/S 28X .......................... 168, 169, 170 Log book .............................................66, 160
DIQCHV ............................................. 178 Calibration entry ....................................72
DIQJB ................................................ 177 Structure ...............................................68
MIQ modules ...................................... 175
Display ....................................................... 55
Display of measured values ....................... 62
M
Display position .......................................... 88 Maintenance condition ................................74
Measured value display ........................48, 56
Measured value recording ........................108
E Displaying recorded measured values ..64
Effects of the weather ................................ 29 Recording duration .............................108
Electrical data Recording interval ...............................108
DIQ/S (24 V version) .......................... 172 Setting the recording duration .............109
DIQ/S (line power version) ................. 171 Setting the recording interval ..............109
Email ........................................................ 106 Settings ...............................................109
Email settings ........................................... 106 Messages ...................................................66
EMC characteristics ................................. 173 Code .....................................................68
Entering texts ............................................. 59 Texts .....................................................70
Error ........................................................... 66 Types ....................................................66
Ethernet ................................................... 111 Monthly load diagram of selected sensor ...64
ba76188e01 03/2017 185

Index IQ SENSORNET
N Site altitude .............................................. 104

Name Software status
Output ................................................... 95 Of all components ................................ 78
Sensor .................................................. 87 Special user qualifications ......................... 17
Network .................................................... 111 Start checklist ............................................. 47
Starting the system .................................... 47
Status info .................................................. 73
O System settings ........................................ 102
Operating elements .................................... 54
Operating principles ................................... 57
Output name .............................................. 95
T
Target group .............................................. 17
TCP/IP ..................................................... 105
P Terminal connections ............................... 174
Password Terminal settings ........................................ 80
change ................................................ 102 Terminal strips (figures) ............................. 53
PID controller (mA output) ........................ 149 Types of installation ................................... 29
Power failure .............................................. 15
Power rating ............................................... 21
Power requirement ..................................... 22
W
Power requirement of individual components Weekly load diagram of selected sensor ... 64
21, .............................................................. 22
R
Relay
Terminal strip ........................................ 53
Retrofitting components ............................. 11
S
Self-test ...................................................... 48
SENSOR connection .................................. 28
SENSOR connection (terminal strip) .......... 53
Sensor name .............................................. 87
Sensor-controlled cleaning ....................... 146
Sensor-sensor link ..................................... 91
Setting the date ........................................ 103
Setting the time ........................................ 103
Settings ...................................................... 80
Air pressure ........................................ 104
Alarms .................................................. 97
Date .................................................... 103
Sensors ................................................ 91
Site altitude ......................................... 104
Terminal ............................................... 80
Time ................................................... 103
Settings of bus interfaces ......................... 108
Settings TCP/IP ........................................ 105
186 ba76188e01 03/2017

DIQ/S 28X Contact Information
14 Contact Information
14.1 Ordering & Technical Support
Telephone: (800) 897-4151

(937) 767-7241
Monday through Friday, 8:00 AM to 5:00 PM ET
Fax: (937) 767-1058
Mail: YSI Incorporated

1725 Brannum Lane
Yellow Springs, OH 45387
USA
Internet: www.ysi.com
When placing an order please have the following information available:
YSI account number (if available) Name and Phone Number

Model number or brief description Billing and shipping address
Quantity Purchase Order or Credit Card
14.2 Service Information

YSI has authorized service centers throughout the United States and
Internationally. For the nearest service center information, please visit
www.ysi.com and click ‘Support’ or contact YSI Technical Support directly at
800-897-4151.
When returning a product for service, include the Product Return form with
cleaning certification. The form must be completely filled out for an YSI Service
Center to accept the instrument for service. The Product Return form may be
downloaded at www.ysi.com and clicking on the ‘Support‘ tab.
ba76188d01 03/2017 187

Contact Information DIQ/S 28X
188 ba76188d01 03/2017

Xylem |'zīləm|
1) The tissue in plants that brings water upward from the roots;
2) a leading global water technology company.
We're 12,500 people unified in a common purpose: creating innovative solutions

to meet our world's water needs. Developing new technologies that will improve
the way water is used, conserved, and re-used in the future is central to our work.
We move, treat, analyze, and return water to the environment, and we help people
use water efficiently, in their homes, buildings, factories and farms. In more than
150 countries, we have strong, long-standing relationships with customers who
know us for our powerful combination of leading product brands and applications
expertise, backed by a legacy of innovation.
For more information on how Xylem can help you, go to www.xyleminc.com
YSI
1725 Brannum Lane
Yellow Springs, OH 45387
Tel: +1 937-767-7241; 800-765-4974
Fax: +1 937-767-1058
Web: www.ysi.com
©Xylem Inc

Diq S 282 284

Uploaded by

Copyright:

Available Formats

Diq S 282 284

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Diq S 282 284

Uploaded by

Copyright:

Available Formats

OPERATING MANUAL

Copyright © 2017 Xylem Inc.

5.3.2 Activating the instrument block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

6 Ethernet connection (variant -E, -EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

8 Maintenance and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

9 What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160

10 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

10.2 General data of MIQ modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175

11 Accessories and options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181

14 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

PC, Tablet PC, Smartphone, ...

-EF (Ethernet fieldbus)

UMTS Modbus TCP

Data Modbus RTU SPS

[-E], [-EF] * Radio

IQ SENSOR NET (Daten + Energie) IQ SENSOR NET

IQ Sensor Power supply Inputs Eingänge

Fig. 1-1 Functional units of the IQ SENSORNET System 28X

Overview Function DIQ/S 28X Variant(s)

Components to Function Component

Maximum extensibility of the system:

A current output (system variant or extra component -CR3 or -CR6) is program-

Fig. 1-2 Simple systems with one and two sensors

1.2 Functions in the IQ SENSORNET

Function Operating manual

1.3.1 USB interface

The USB interface is equipped with a protective cover.

1.3.2 Ethernet interface (DIQ/S 28X-E[F])

1.3.3 Fieldbus interface (DIQ/S 28X -MOD, -PR, -EF)

The following variants of the DIQ/S 28X have a fieldbus interface:

DIQ/S 28X variant Fieldbus connection

1.4 Behaviour of the system to a power failure

2.1.1 Safety information in the operating manual

This operating manual provides important information on the safe operation of

2.1.2 Safety signs on the product

2.1.3 Further documents providing safety information

The following documents provide additional information, which you should

2.2 Safe operation

2.2.1 Authorized use

2.2.2 Requirements for safe operation

Note the following points for safe operation:

2.2.3 Unauthorized use

The product must not be put into operation if:

2.3 User qualification

3.2 Basic principles of installation

3.2.1 Requirements of the measurement location

The measurement location must meet the environmental conditions specified in

3.3 Safety requirements of the electrical installation

(according to the technical data of the instrument input or output)

3.4 Installation guidelines for lightning protection

The internal device-related protective measures are already integrated in the

Background: The formation of highly lightning hazardous inductive loops be-

to provide general and consistent protection via gas overvoltage surge

3.5 Drawing up the power rating

Only IQ SENSORNET products may be used in the IQ SENSORNET.

Sum of the power requirement ≤ Sum of the power delivery

The power rating provides an initial guide value. In specific limiting

Component Power delivery [W]

The power requirement of the individual components is listed in the following