Scribd
Upload
126 views3 pages

PX4211 2

The document provides instructions for an end semester practical examination for an M.E/M.Tech program in Power Electronics and Drives Laboratory. Students must complete one of 20 experiments related to simulating or modeling various motor drives and controllers using MATLAB/Simulink. The experiments involve topics like induction motor control, DC motor speed control, inverter drives, and more. Students will be evaluated on their calculations, tabulations, circuits, results, programs/models, and performance during a viva voce interview.

Uploaded by

kalpana
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
126 views3 pages

PX4211 2

The document provides instructions for an end semester practical examination for an M.E/M.Tech program in Power Electronics and Drives Laboratory. Students must complete one of 20 experiments related to simulating or modeling various motor drives and controllers using MATLAB/Simulink. The experiments involve topics like induction motor control, DC motor speed control, inverter drives, and more. Students will be evaluated on their calculations, tabulations, circuits, results, programs/models, and performance during a viva voce interview.

Uploaded by

kalpana
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

M.E / M.Tech.

PRACTICAL END SEMESTER EXAMINATIONS, APRIL/MAY 2022

Second Semester

PX4211 - POWER ELECTRONICS AND DRIVES LABORATORY

(Regulations 2021)

Time : 3 Hours Answer any one Question Max. Marks 100

Calculations,
Aim/Principle/Apparatus Tabulation/Circuit/
Results & Viva-Voce Record Total
required/Procedure Program/Drawing
waveform
20 30 30 10 10 100

To simulate the three phase Induction motor for the following.


1. Forward and reverse motoring
1. 100
2. Forward and reverse regenerative braking.

Simulate and analyze the closed loop control of Converter fed DC drive with
2. 100
suitable waveform.

Construct a MATLAB Simulink model of speed control of Converter fed DC


3. 100
motor.

Construct a MATLAB Simulink model of speed control of Chopper fed DC

motor, and draw the On time and off time of a chopper.

4. 100

Study the Simulation of voltage source inverter fed Three Phase Induction

motor drive by Using Simulink.


5. 100

Page 1 of 3
Construct a MATLAB Simulink model of V/f control of Three-Phase Induction
6. 100
motor and draw the output waveforms.

Obtain the speed control of Stepper motor by using Micro controller and draw
7. 100
the waveforms.

Construct a MATLAB Simulink model of Speed control of Brush Less DC


8. 100
(BLDC) motor and draw the output waveforms.

Construct a model for the DSP based speed control of SRM motor and draw
9. 100
the waveforms.

Construct a MATLAB Simulink model of Four quadrant operation of three-


10. 100
phase induction motor and draw the relevant waveforms.

Draw the input and output waveforms of Voltage Regulation of three-phase


11. 100
Synchronous Generator.

Obtain the input and output waveforms of the AC voltage Controller based
12. 100
speed control of Induction machine.

Construct a MATLAB Simulink model of current source inverter fed Three


13. 100
Phase Induction motor drive and draw its output waveforms..

Construct a MATLAB Simulink model of DSP based closed loop speed control
14. 100
of SRM motor and draw the necessary waveforms.

Conduct a suitable experiment speed control of Induction motor to convert


15. 100
from fixed AC voltage to variable AC voltage without changing the frequency

Design a single phase Induction motor based AC Voltage Controller by using


Triac and diac.
16. 100

Page 2 of 3
How to control the direction and speed of a stepper motor interface with
17. PIC microcontrollers PIC16F877A, and calculate the half step and full
step rotation.

Construct a MATLAB Simulink model of three phase ac voltage controller with


18.
Resistive load and draw its output waveforms.

19. To control the speed of brushless DC motor using digital simulation.

Suggest a suitable experiment, the duty cycle of chopper is varied by varying

20. ON and OFF time of chopper, the speed of motor can be varied and draw the
on/off time waveform.

Page 3 of 3

You might also like