DESIGN OF INTERMEDIATE SPAN ROOF PURLIN
CLIENT:- RTDC
LOCATION:- LIBRARY BUILDING
INPUT FOR DESIGN
Width of the Building, B = 17.77 m
Length of the Building, D = 40.7 m
Height of the Building, H = 13.05 m
Bay Spacing,L = 7.64 m
Max. Purlin Spacing, Ps = 1.5 m
Roof Slope, In X Direction = 2.5 Kx = 0.928
In Y Direction = 1 Ky = 0.371
Dead Load Intensity, DL = 15 Kg/m2
Live Load Intensity, LL = 75 Kg/m2
Wind Load Intensity,WL = 74.00 Kg/m2
Net Pressure Co-eff for Wind = -1.1 (FROM IS 875-Part 3)
Yield Stress Of Steel, Fy = 345 MPa
No. of sag Rods at Intermediate Purlin = 1
Surface across the Wind Direction = Smooth surface without corrugations or Ribs
SECTIONAL PROPERTIES OF PURLINS:(AS PER CLAUSE 5.2 OF IS 801-1975)
TRY Z-200X2.0
t d b1 b2 L1 L2 D
Actual Sizes (As per Standard) 2 196 64 66 18 18 200
Effective Sizes for Stress Calc. 2 196 60 60 18 18 200
Effective Sizes for Deflection Calc. 2 196 64 66 18 18 200
Centre Of Gravity, Y = 10.01 cm Centre Of Gravity, X = 5.90 cm
4
Moment of Inertia, Ixx = 413.09 cm Moment of Inertia, Iyy = 49.14 cm4
3
Sectional Modulus, Zxxtop = 41.27 cm Sectional Modulus, Zyyleft = 8.33 cm3
Sectional Modulus, Zxxbot = 41.35 cm3 Sectional Modulus, Zyyright = 8.30 cm3
2
Cross Sectional Area, A = 7.16 cm Weight/m = 5.62 Kg.
DESIGN OF INTERMEDIATE SPAN PURLINS: (AS PER IS 801-1975 & IS 800-2007)
LOAD CALCULATIONS:
Major Loads, Load in Vertical Plane:
Total Load, DL+LL Case [(DL + LL) x Kx] x Ps = 125.34 Kg/m
Total Load, DL+WL Case [(DL x Kx + WL x Cp1) x Ps] x = -75.91 Kg/m
Minor Loads, Loads in Inclined Plane:
Total Load, Design Governing Case (DL+LL) x Ky x Ps = 50.14 Kg/m
Moment At Varoius Locations:
Maximum Span Moment, Mspan = 266 Kg-m
Maximum Span Moment over Sag Rod, Msag = 26.63 Kg-m
Maximum negative Moment near Support, Msupp = -542 Kg-m
Maximum moment capacity of Section, Mmax = 854 Kg-m
Moment at Lap, L1 0.385m from Support, ML1 = -433 Kg-m
Moment at Lap, L2 0.770m from Support, ML2 = -225 Kg-m
Moment at Lap, L3 1.155m from Support, ML3 = -237 Kg-m
Mnimum Lap Required = 385 mm
2
DESIGN OF INTERMEDIATE SPAN ROOF PURLIN
CLIENT:- RTDC
LOCATION:- LIBRARY BUILDING
ALLOWABLE STRESSES IN WEB OF PURLINS:(AS PER CLAUSE 6.4 OF IS 801-1975)
Shear stresses in Web:
Maximum average shear stress, Fv = 5850000/(d/t)²
= 609.12 kg/cm2
Developed shear stress, fv, P x L / Aw = 244.29 kg/cm2 SAFE
Bending Stress in Web:
Maximum Bending stress, Fbw = 0.6 x Fy
= 2070 Kg/cm2
Developed Bending Stress Vertical Plane, Mspan / Zxmin = 645.3 Kg/cm2 SAFE
Developed Bending Stress Inclined Plane, Msag / Zymin = 320.8 Kg/cm2 SAFE
Total Bending stress, fbw = 966.1 Kg/cm2 SAFE
Combined Bending and Shear Stress in Web:
fbw2 fv2 SAFE
= 0.62
2
Fbw Fv2
DEFLECTION CHECK : (AS PER TABLE 6 IN IS 800:2007)
Sectional Properties:
Centre Of Gravity, Y = 10.06 cm Centre Of Gravity, X = 6.34 cm
Moment of Inertia, Ixx = 432.28 cm4 Moment of Inertia, Iyy = 60.39
Sectional Modulus, Zxxtop = 42.99 cm3 Sectional Modulus, Zyyleft = 9.35
Sectional Modulus, Zxxbot = 43.47 cm3 Sectional Modulus, Zyyright = 9.52 cm3
2
Cross Sectional Area, A = 7.16 cm Weight/m = 5.62 Kg.
Permissible Deflection, Span/150 = 50.9 mm
4
Maximum Deflection, 0.0065wL /EI,
For DL+LL = 32.1 mm SAFE
For DL+WL = 26.1 mm SAFE
PROVIDE Z-200X2.0 INTERMEDIATE SPAN PURLIN WITH A MINIMUM OVERLAP OF385 mm.
