Skypatrol SP1824 User

Manual V2.0
Updated by 2022-9-10

1 / 12
 Content
Preface ..................................................................................................... 3
1. Product Introduction .............................................................................. 4
2. Technical Parameters ............................................................................. 5
3. Define of LED indicator .......................................................................... 6
4. Device Installation ................................................................................. 6
4.1 Prepare works ................................................................................................ 6
4.2 SIM Card Installation .................................................................................... 6
4.3 Device Connection Description.................................................................... 7
4.4 Device Install Position .................................................................................. 7
5. Common Fault analysis .......................................................................... 8
6. Commands ............................................................................................ 8
7. Serial Port configuration ....................................................................... 12

2 / 12
Preface

Thank you for choosing the company's AT100 GPS tracking products,
please carefully read the instructions before operating.

Please check the items in package with packing list, contact with the distributor
when you found something leave out.

Disclaimer：
➢ Read this user manual carefully please. When you start use this product, then you are
deemed to have read this user’s manual.

➢ This Product used as assistant tool for Security only, can’t prevent all kinds of
deliberately theft or malicious damage vehicles. For the safety of your assets, you still
need keep necessary vigilance and security awareness after you installed this product.
We do not bear responsibility to any loss except product itself. Thanks!

3 / 12
1. Product Introduction

AT100 is 4G CAT1 tracking device, which combined with positioning, monitor, alarm and
tracking functions, with small size it’s easy to use and operate, main applies to vehicles
and other mobile object location and tracking service, with widely voltage support, it can
used with motorcycle and Electric vehicles.

Product Features:
◼ Support 9-95V widely power supply.
◼ Support external power cut alarm.
◼ Build-in GSM/GPS antenna.
◼ Vehicle mileage statistic.
◼ Remote Cut/Recover Engine.
◼ Support remote upgrade by OTA.
◼ Support vibrate alarm.
◼ Support over speed alarm.
◼ Support remote configure by SMS/GPRS.

Note:
✓ This product function based on GPRS network; need a SIM card which have GPRS
data transmit and SMS functions.
✓ SIM card is not include in the packing list, please prepare SIM card before you use
this device.
✓ This product work voltage is (9-95V/DC ), lower or higher will make device work
improper.

4 / 12
2. Technical Parameters

Name Parameters
4G CAT1 (SIMCOM) Optional:
SIMCOM A7670C
LTE-FDD:B1/B3/B5/B8
LTE-TDD:B34/B38/B39/B40/B41
GSM:900/1800 MHz

A7670E
LTE-FDD: B1/B3/B5/B7/B8/B20
GSM: B3/B8

A7670SA
LTE-FDD: B1/B2/B3/B4/B5/B7/B8/B28/B66
GSM: B2/B3/B5/B8

A7670(OPEN)
LTE-FDD:B1/B3/B5/B8
LTE-TDD:B34/B38/B39/B40/B41
Color Black
GPS module XM1010/AT6558D
Working Voltage 9V~95V
Working Current Around 50mA@12V
Standby current Around 10mA@12V
Back-up Battery 140mAh(optional)
Back-up Battery working About 2 hours
time
Tracker size 80mm*38m*17mm
Tracker weight 50g around
Working temperature -20℃ - +75℃
Moisture 10% - 85%
Locate Sensitivity 10m
Locate time Hot start(average): <1s
Cold start(average): <32s
GPS Sensitivity -162dbm
GPS frequency L1:1575.42±1.023MHz
LED Indicator Use yellow/blue two color LED indicator to
show the status of power/GSM/GPS.
Blind area data 5000 records

5 / 12
3. Define of LED indicator

LED Color Status Status describe

GSM Yellow/orange Light static GPRS communicate normal,
status Online
Fast blinking (2s blink once) initializing

LED OFF GSM in sleep/device OFF

GPS Blue Light static GPS Located

status
Fast blinking (2s blink once) Finding GPS signal

LED OFF GPS in sleep

4. Device Installation

Before you start install the device, Please check the product you get with the packing list,
if you have any problem please contact us or distributor in time.

4.1 Prepare works

 GPS product AT100

 Local GPRS SIM card
 12V/24V DC power supplier

4.2 SIM Card Installation

This device need install a SIM Card, which must have 4G/GPRS data
transmission and SMS function.

Note:
▪ Do not install SIM Card in opposite way.
▪ SIM Card must open 4G/GPRS data transmission function
▪ Confirm the SIM Card have enough balance inside.
▪ Test SIM card by cellphone to check if it can connect network
▪ Please do not remove or insert SIM Card without power off, to avoid the damage to
SIM card and device

6 / 12
4.3 Device Connection Description

Color Describe
4PIN Red Power(9-95V)
Black GND
Orange ACC
Yellow OUTPUT(relay)
2PIN(Optional) White SOS+
White SOS-

4.4 Device Install Position

To install this device you need have some necessary knowledge about Car Electronics. So
please make sure you have right person to make the first installation.
In the installation process, do not power on device. The following is some problem may
facing in the installation process, please note:

There have two kind of way to install the device: Hidden install and Open type install.
When install in special-purpose vehicle you can select hidden install, and when install in
temporary vehicle you can select Open type install.
I. To avoid be broken, the install position of the device should be hidden. The suggest positions are:
 Covert within the dalle below the front windshield glass;
 Covert around the front instruments panel (the cover of the instruments should not be metal)
 Place Under the dalle below the rear windshield glass of the car.
II. Avoid the positions round emitters, such as reverse sensor, burglar alarm and other vehicle-mounted
communication devices.
III. Use the ribbon or sponge powerful double-sided adhesive to fasten the device.
IV. The device GSM Antenna and GPS Antenna are build-in, please make sure the GPS receiving surface
(the side with LED indicator) face to sky and no metal shelter above when install.
Note:
 If there have metal thermal-protective coating or warm up coating on the windshield glass, the GPS
signal will be damped. That may cause the device work abnormal, please change install position.
 If you want to install the device by Open type, you can paste the Velcro tape on the dalle below the
front windshield glass, and then fasten the device on it.

7 / 12
 5. Common Fault analysis

Issue Analysis Describe

Can’t get online Power supply abnormal
Sim issue No balance,no GPRS, Install
incorrect
Setting issue IP,PORT,ID,APN wrong
GPRS signal weak
Server issue
Can’t get location GPS signal weak Test with open sky area
Installation reversed The antenna side need face
to sky

6. Commands

➢ A-Telematics Protocol SMS commands

Name Command Reply Instruct

Enable log AT%TEST=*1234,280*1#

Set server IP/Port AS1234*269#1,120.24.225.253,55 120.24.225.253;5577,1; Reply content is “IP”

77,1# OK “Port”, connection type:
0: UDP; 1: TCP
AS1234*269#1,tracking.skypatrol.
Set URL/domain
com,5577,1#
Set IP2 AS1234*269#I2,120.24.225.253,5 X=0: close IP2;
577,1,x# X=1: 2 IP work same;
X=2: IP2 only work as
backup server(IP1 can’t
connect then connect
IP2).
Set IP2 as url AS1234*269#I2,url,5577,1,x#

Set Device ID AS1234*269#2,12007845# 12007845;OK Current “ID”

Set APN AS1234*269#3,CMNET,,,# CMNET,,;OK APN setting

Restart Device AS1234*269#B# GSM/restart; OK Device restart

8 / 12
Factory set AS1234*269#F# Reset OK; All parameters recover
to factory, beside
IP/Port/ID/APN
Check connection AS1234*269#C# *U:122.114.126.6,6666, *N: device ID;
info 1*A:cmnet,,*N:3423180 M6: Online;
1,M6,N1,60,3600,Q25
G1,8: G1 locate, G0 not
,G1,8,Z+0,AT08FV1.0
locate, 8 located satellite;
Z+0: Timezone, GMT+0.
Change SMS AS1234*269#4,5678# PWD:5678,OK
password
Angle:30, OK
Angle upload
AS1234*269#9,X#
Position query2 AS1234WHERE2# http://maps.google.com/
maps?hl=en&q=+22.59
303,+113.87110

Open/close Sleep AS1234*269#I,SX# X=0, close sleep mode; When open this
mode X=1, open sleep mode function, device will turn
to sleep mode when ACC
off for 5 mins. and wake
up when ACC on or
alarm or SMS trigger.
Check FW version AS1234*269#V# Version:TFB402 V1.5 Jul
31 2017 11:13:27
Set the authorized AS1234*269#5,XXX,XXX, XXX,XXX,XXX,XXX, set
SIM number XXX,# ok
Authorized SIM AS1234*269#P# 8612345678912,,,,;OK To check the authorized
number query numbers.
Cut fuel AS1234ENGINE:OFF# ENGINE:OFF;OK IMMOBILIZE at once

Cut fuel with AS1234*269#O1,1# IF speed>30km/h, do

condition not immobilize;
If speed<=30km/h,
immobilize with
duration(5times
ON/OFF),and cut oil
totally after 30s.
Recover fuel Recover at once
AS1234ENGINE:ON# ENGINE:ON;OK

Recover fuel with IF speed>30km/h, do

condition not recover;
AS1234*269#O1,0# If speed<=30km/h,
recover with
duration(5times

9 / 12
 ON/OFF),and cut oil
totally after 30s.
X is 0-12. Example:
Set TIMEZONE AS1234*269#I,Ex/Wx# set GMT+8 Command:
AS1234*269#I,E8#
x=ACC ON upload
SMS set ACC
interval，
ON/OFF upload AS1234*269#7,x,y#
y=ACC OFF upload
interval
interval
unit：km/h；x is
SMS set over speed；
SET SPEED:30(Km/h),
speed AS1234SPEED:x,y# Y: duration time trigger
5(s);OK
over speed, unit is
seconds;
X=mileage value, unit is AS1234*269#m,1111#
Set mileage value AS1234*269#m,x#
KM. MILEAGE:1111(Km);OK
AS1234*269#T#
Check IMEI IMEI: 460079155373814
AS1234*269#S#
if you enable upload by
distance, then distance
and time base will work
Upload by distance AS1234*269#d,x# Unit is meter.
both, which condition
matched, then upload
position once.
Set mileage ratio AS1234*269#L,1,X,# X range: 100-200 AS1234*269#L,1,110,#

Check mileage MileageRate:110;OK

AS1234*269#L,0#
ratio
X=over speed value;
Set over speed AS1234*269#OS,x,y,# Y=duration trigger time,
unit is seconds.
Set Move x=move distance, unit is
AS1234*269#mv,x#
alarm(ACC OFF) m(ACC OFF, x>100m)
x is idle speed, y is IDLE:8,5;OK
Set idle alarm AS1234*269#i,x,y#
duration, unit is minute;
Enable position X=1,Open ACK;
ACK AS1234*269#*M,x# X=0, close ACK.
Set harsh Default:
AS1234*269#a1,X,#
accelerate Accelerate:14km/h/s
Default:
Set harsh brake AS1234*269#a2,X,#
Decelerate:20km/h/s
X=speed, unit is km/h; Need update FW.
GPS harsh corner AS1234*269#a4,x,y,z# Y=angle;
Z=duration time.
Query harsh AS1234*269#a#

10 / 12
acc/brake
parameters
AS1234*269#W,120.24.225.253,2
OTA CMD
002;#
D:200m; sp:50,3s; D:upload by distance;
idl:8,3; mv:500; sleep:0; Sp: over speed;
ack:0; acc:0; sos:0; idl: idle;
power:0 Mv: ACC OFF moving
alarm distance;
Check alarm Sleep: 1 sleep mode on;
parameters Ack: 1 enable position
ack;
Acc: 1=ACC ON;
SOS: 1= SOS ON;
Power: 1 main power
AS1234*269#R# normal
Set heartbeat k is small case,
interval AS1234*269#K,x# Unit is seconds
Query heartbeat
interval AS1234*269#K#
X=0, unit is KM(default);
Mileage unit
AS1234*269#*y,x# X=1, unit is 0.1km
a=SPEED for trigger ACC Please note:
ON; Command code is
b=speed duration time number 0, but not
for trigger ACC ON; character o
c=speed for ACC OFF,
ACC detect by speed need be>=1, 0 Unit is seconds.
speed means disable detect
ACC OFF;
d=speed duration time
AS1234*269#0,a,b,c,d# for trigger ACC OFF
QUERY AS1234*269#0#
A=Over-speed; 1=enable;0=disable.
B=ACC ON;
C=ACC OFF;
D=Idle;
E=Move
SMS alarm enable
F=Enter Geo-fence
G=Exit Geo-fence
AS1234*269#ESMS,A,B,C,D,E,F,G, H=Harsh accelerate
H,I,J,K# I=Harsh decelerate
J=Harsh corner

11 / 12
7. Serial Port configuration

Default Baud rate:115200;

Tool: SSCOM;
Via: USB port.
Enable log cmd: AT%TEST=*1234,280*3#

12 / 12