DATA SHEET

LinkRunner® AT
Copper & Fiber Autotester
Overview
The LinkRunner® AT offers user-configured auto-tests for a wide range of important tasks.
This network tester’s quick cable test and switch identification facilitates fast problem
isolation. Test results can be automatically uploaded to the Link-Live results management
cloud service to improve collaboration between network engineers and technicians,
creating greater job visibility, project control, and fleet management. ​
• Discover nearest switch name and port information via CDP/LLDP/EDP and verify link
speed/duplex and connectivity to TCP/IP network with AutoTest
• Validate up to 30W 802.3af/at PSE with TruePower™ loaded Power-over-Ethernet (PoE)
test
• Verify twisted-pair cable length and wire-map in a snap
•   AutoTest verifies and documents PoE, nearest switch, DHCP, DNS and Gateway
service, and key devices connectivity in one go
• Automate reporting and enable collaboration with result upload and
management via Link-Live Cloud Service

Key Features
1000 2000

Two Models: LRAT-2000 and LRAT-1000

LinkRunner AT is available in two models: LRAT-2000 and LRAT-1000. LinkRunner AT 2000 adds the following exclusive
features:
• Fiber support* • TruePower™ PoE Power - test up to 30W*
• IPv6 support* • Reflector support*
• More result storage: 50 instead of 10* • Uses Li-ION rechargeable battery instead of AA battery pack

Capability Comparison
DO YOU NEED LRAT-1000 LRAT-2000
Test PoE 30W loaded •
Performance Test Reflector •
Perform Cable Test • •
Perform Switch Test • •
Perform DHCP, DNS, and Gateway Test • •
Test IP Target 10 10
Battery AA X 4 Li-ION
*These exclusive features cannot be added to the LinkRunner AT 1000. Left: LRAT-2000 / Right: LRAT-1000

1
 Cable length, Wiremap, and Location
Users can easily find opens, shorts, miswires, and split pairs in three different ways:
• On non-terminated cable
• With a WireView Cable Identifier
• Check patch cord with the built-in wiremap port on the side of the LinkRunner AT

Cable Location
Locate cable runs with toning, switch port advertisement, switch port link light
blinking, and remote cable identifiers. Toning supports both analog and digital
IntelliTone modes

Discover Nearest Switch and VLAN

The LinkRunner AT uses the IEEE Link Layer Discovery Protocol (LLDP), along with the
Cisco and Extreme Discovery Protocols (CDP and EDP) to display the nearest switch Cable wiring validation
model, slot, port and VLAN configured.
The LinkRunner AT displays the following critical nearest switch information:
• Switch name and model
• Chassis, slot and port
• Switch IP address
• Voice and Data VLAN IDs
• Duplex and speed (actual and advertised)
• Signal Strength
Switch information
• Connection (MDI or MDI/X)
• PoE voltage and power (actual and test limit)
• Graphical representation of power on pairs

Packet Reflector
The LinkRunner AT features a packet reflector mode that allows the device to be used
remotely during end-to-end network path performance tests to validate LAN and WAN
throughput capabilities, up to 1Gbps. The reflector mode can be configured to swap
MAC and/or IP addresses. LinkRunner AT 2000 supports packet reflection for: Packet Reflector Mode

• EtherScope™ nXG Portable Network Expert

TruePower™ PoE Testing - Power Over Ethernet Testing

LinkRunner AT features the ability to validate TruePower delivery before installing
cameras, APs, and phones to ensure a smooth deployment. Quickly validate PoE
performance by drawing actual power up to the 802.3at standard 25.5W. Load the
circuit to stress switches, cabling and patch panels, all while measuring the voltage and
pairs being used. PoE Setup

IP V4/V6 Addressing
Validate the IPv4 DHCP auto-negotiation process, subnet and DHCP server and verify
IPv6 Link-Local and Global addressing.

Key Service and Device Connectivity

LinkRunner AT can perform either a Ping or a TCP port open test to verify connectivity.
The test conducted will reveal connection and response time to the default Gateway, AutoTest Results
preferred DNS server, and alternate DNS server. LinkRunner AT can connect to as many
as 10 user-defined target devices, servers or services, testing using Ping, or a user-
defined TCP port number. If a URL is used as the target, results will include response
time and an IP address.

802.1x Authentication
Verify access to secure networks using 802.1x and MAC Access Control Lists (ACL). The
included LinkRunner AT Manager Software can be used to enable 802.1x and download Configuration Settings
certificates.
2
 Automated Test Results Management
Serving as a centralized test results and device management system, the free
Link-Live Cloud Service transforms team workflows with the ability to quickly
and easily log, document, and report test activity from all LinkSprinter®,
LinkRunner AT, LinkRunner G2, LinkRunner 10G, AirCheck™ G2 handheld
network testers.
Once the instrument is connected to the Link-Live Cloud service, your test
results are automatically uploaded to the dashboard for project management
and reporting. You have the option of uploading additional files, screenshots,
images, profiles, packet captures, location information, and comments anytime.
Also, certain NetAlly instruments with AllyCare Support can receive firmware Simplify report generation across media types for
updates “over the network” from Link-Live as they become available. network deployment documentation
An API is available to retrieve and integrate data from Link-Live into other
management platforms, such as your trouble-ticket application or network management
system. This gives you the ability to easily provide proof-of-performance and better
manage jobs and staff efficiency.
This unified dashboard of both wired and Wi-Fi network connectivity results enables you to:
• Reduce results management overhead for multiple testers and users
• Enables seamless collaboration between site personnel and remote experts
• Attach photos, user comments to each result, adding context for future changes and troubleshooting
• For asset management, ability to associate serial numbers of installed devices, and/or cable/walljack label to specific test
results

Ordering Guide
Model Number/Name Description
Includes: (1) LinkRunner AT 1000 tester with AA battery pack, 4 AA batteries, WireView Cable ID #1,
LRAT-1000
USB cable, Quick Start Guide, and soft case.
Includes: (1) LinkRunner AT 2000 tester with Li-ion battery, power supply with regional power
LRAT-2000 plugs, WireView Cable ID #1, RJ-45 coupler, USB cable, Quick Start Guide and soft case. Fiber SFP
must be purchased separately.
Includes: (1) LinkRunner AT 2000 tester with Li-ion battery, power supply with regional power
LRAT-2000-KIT plugs, WireView Cable ID #1-#6, RJ-45 coupler, Quick Start Guide, USB cable, holster, and
medium soft case. Fiber SFP must be purchased separately.
Includes: (1) LinkRunner AT 2000 tester, (2) LinkSprinter network testers, (1) LinkRunner AT holster,
LINKSOLUTIONS-KIT
and (2) LinkSprinter holsters.
Includes: (1) AirCheck G2 Wi-Fi Tester, AC charger, (2) USB cable, Quick Start Guides, external
directional antenna, holster, automobile charger, (1) LinkRunner AT 2000 tester with Li-ION
ACKG2-LRAT2000
battery, AC charger, WireView Cable ID #2-6, large folding test kit pouch, holster, RJ-45 coupler,
and (2) soft carrying cases.

Support
Model Number/Name Description
LRAT-1000-1YS 1 year AllyCare Support for LRAT-1000
LRAT-1000-3YS 3 year AllyCare Support for LRAT-1000
LRAT-2000-1YS 1 year AllyCare Support for LRAT-2000
LRAT-2000-3YS 3 year AllyCare Support for LRAT-2000

1 year AllyCare Support for AIRCHECK-G2, AIRCHECK-G2-KIT, AIRCHECKG2-TA-KT, ACKG2-LRAT2000

AIRCHECK-G2-1YS
(covers ACKG2 only) and LR-G2-ACKG2-CBO (covers ACKG2 only)

3 year AllyCare Support for AIRCHECK-G2, AIRCHECK-G2-KIT, AIRCHECKG2-TA-KT, ACKG2-LRAT2000

AIRCHECK-G2-3YS
(covers ACKG2 only) and LR-G2-ACKG2-CBO (covers ACKG2 only)

3
Accessories
Model Number/Name Description
PWR-CHARGER AC Charger replacement
WBP-LION-GREEN LinkRunner AT Lithium Ion Replacement Battery
LRAT-AA-GREEN LinkRunner AT AA Battery Pack
LRAT-HOLSTER LinkRunner AT Holster
SFP-1000SX SX Gig Fiber SFP transceiver with DDM (850 nm, Multimode)
SFP-1000LX LX Gig Fiber SFP transceiver with DDM (1310 nm, Singlemode)
SFP-1000ZX ZX Gig Fiber SFP transceiver (1550 nm, Singlemode)
SFP-100FX 100BASE-FX Fiber SFP transceiver with DDM (Multimode)
WIREVIEW 1 WireView wire mapper #1
WIREVIEW 2-6 WireView wire mappers #2-#6
MS-AUTO-CHG Auto Lighter Charger Adapter

Specifications
General
Dimensions 3.5 in x 7.8 in x 1.9 in (8.9 cm x 19.8 cm x 4.8 cm)
Weight 18 oz (0.5 kg)
LRAT-1000 - 4 AA alkaline batteries
Battery
LRAT-2000 - Removable, rechargeable lithium-ion battery pack (18.5 Watt-hrs)
Battery Life Typical operating life is 6 hours; Typical charge time is 3 hours
External AC Adapter/
AC input 90 to 264V AC 48 to 62 Hz input power DC output 15V DC at 1.2 Amps
Charger
Display 2.8 in color LCD (320 x 240 pixels)
Keypad 12-key elastomeric
Tone Generator IntelliTone™ digital tone: [500 KHz]; analog tones: [400 Hz, 1 KHz]
Media Access; Copper RJ-45: 10BASE-T, 100BASE-TX, 1000BASE-T and PoE (IEEE 802.3af and 802.3at)
Media Access; Fiber SFP Adapter Port supports 100BASE-FX and 1000BASE-LX/ SX/ZX (LRAT-2000 Only)
Cable Tests Pair lengths, opens, shorts, splits, crossed, straight through, and cable ID

Power over Ethernet Single ended testing:

(PoE) - User-defined testing to IEEE 802.3at class 0, 1, 2, 3, 4 without LLDP negation, or 4 with LLDP
negotiation
The following PSE PoE parameters are measured:
- Pairs used
- Received class
- PSE type
- Unloaded voltage(V)
- Loaded voltage (V) (LRAT-2000 with TruePower™)
- Unloaded power (W) (LRAT-1000)
- Loaded power (W) (LRAT-2000 with TruePower™)

4
Specifications continued
Environmental
32°F to 113°F (0°C to +45°C)
Operating Temperature
NOTE: The battery will not charge if the internal temperature of the tester is above 122°F (50°C).
Operating relative 90% (50°F to 95°F; 10°C to 35°C)
humidity (% RH without
condensation) 75% (95°F to 113°F; 35°C to 45°C)

Storage temperature -4°F to 140°F (-20°C to +60°C)

Shock and vibration Random, 2 g, 5 Hz-500 Hz (Class 2) 1 m drop
Safety EN 61010-1 2nd edition
Safety (LR-AT 2000 only) EN/IEC 60825-1:2007, EN/IEC 60825-2:2004+ A1:2007 (LRAT- 2000 only)
Altitude 4,000 m; Storage: 12,000 m
EMC IEC 61326-1: Basic Electromagnetic Environment; CISPR 11: Group 1, Class A

Supported Operating
Windows® Vista, Windows® XP, Windows® 7, Windows® 8, Windows® 10
Systems
400 MHz Pentium processor or equivalent (minimum); 1 GHz Pentium processor or equivalent
Processor
(recommended)
RAM 96 MB (minimum); 256 MB (recommended)
Hard Disk Up to 500 MB of available space may be required
Display 1024 x 768 high color, 32-bit (recommended)
Certifications and Compliance
Conforms to relevant European Union directives
Conforms to relevant Australian Safety and EMC standards
©2022 NetAlly®, LLC. Third-party trademarks mentioned are the property of their respective owners.

LRAT-DS-22-V1

eudisa GmbH Telefon: +49 89 9041011-12

Maria-Merian-Strasse 8 E-Mail: [email protected]
85521 Ottobrunn b. München Website: www.eudisa.com

BERATUNG | SCHULUNG | SERVICE | WISSEN