Scribd
Upload
30 views1 page

Steel Sucker Rod

This document summarizes the specifications and mechanical properties of various grades of steel sucker rods used in oilfields. It describes Grade C and D rods, with Grade C having moderate strength, good plasticity, and corrosion resistance suitable for sour medium environments. Grade D has higher strength, plasticity, and service life suitable for deeper wells. The document provides the sizing, threading, and length specifications for different rod sizes from 5/8 to 1-1/8 inches. It also lists the required yield strength, tensile strength, elongation, contraction area, and impact toughness for Grades C through HS, and notes special alloy rods are also available. Contact information is provided at the bottom for further inquiries.

Uploaded by

Santii Campitelli
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
30 views1 page

Steel Sucker Rod

This document summarizes the specifications and mechanical properties of various grades of steel sucker rods used in oilfields. It describes Grade C and D rods, with Grade C having moderate strength, good plasticity, and corrosion resistance suitable for sour medium environments. Grade D has higher strength, plasticity, and service life suitable for deeper wells. The document provides the sizing, threading, and length specifications for different rod sizes from 5/8 to 1-1/8 inches. It also lists the required yield strength, tensile strength, elongation, contraction area, and impact toughness for Grades C through HS, and notes special alloy rods are also available. Contact information is provided at the bottom for further inquiries.

Uploaded by

Santii Campitelli
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

www.suckerrod-china.

com
HIGHLAND SHENGLONG
STEEL SUCKER ROD

Steel Sucker Rod

Steel sucker rod is the major equipment for oilfield. We providegrade C, D, K,


KD, HL, HS and special alloy sucker rod which are made according to API
Spec 11B. Grade C sucker rod is made of fine carbon-steel, featured by
moderate strength, good plasticity and better corrosion-resistance. Grade C
sucker rod is suitable for sour medium environment where they are not
susceptible to sulphuric stress cracking.
Grade D sucker rod is made of fine alloy steel with feature of high strength,
better plasticity and long service life after heat treatment. Grade D sucker rod
is suitable for deeper oil well in the non-corrosion or light- Steel Sucker Rod corrosion medium.
Technical Specification of Steel Sucker Rod:
Sucker Rod Rod (in) THREAD (in) ROD LENGTH (ft)
Size (in)
5/8 5/8 (+0.007,-0.014) 15/16

3/4 3/4 (+0.008,-0.016) 1-1 /16


25

7/8 (+0.008,-0.016) 26
7/8 1-3/16
30
1 1 (+0.009,-0.018) 1-3 /8
Pony Rod
1 1/8 1 1/8 (+0.010,-0.020) 1-9 /16
Mechanical Properties of Steel Sucker Rods:
Sucker Rod Yield Strength Tensile Strength σb Elongation ∆ Contraction Area Impact Toughness αk
Grade σs (Mpa) (Mpa) (%) Ψ (%) (J/cm2)

C ≥500 621~793 ≥12 ≥55 ≥60.8

D ≥620 793~965 ≥10 ≥50 ≥58.8

K ≥414 621~793 ≥12 ≥60 ≥70

KD ≥586 793～965 ≥10 ≥50 ≥58.8

HL ≥793 965～1195 ≥10 ≥50 ≥60

HS ≥793 965～1034 ≥10 ≥50 ≥60

Special Alloy

www.suckerrod-china.com, Email: [email protected],

Mob,WhatsApp,Viber: 86 18866716080

You might also like