MacRoy D IOM

MacRoy® D Metering Pump
IOM Manual
Manual No. : 53872
Rev. : 01
Rev. Date : 05/2019
PRECAUTIONS
For Pumps with PVC & 316SS Liquid Ends
WHEN USED IN SWIMMING POOLS OR SPAS / HOT TUBS (ANSI / NSF 50)
Caution on Chemical Concentration:

There is a potential for elevated chemical concentration during periods of no flow, for
example, during backwash in the system. Steps, such as turning the pump off, should be
taken during operation or installation to prevent this. Contact your sales representative or
distributor about other external control options to help mitigate this risk.
Flow Indicating Device:

To ensure operation of the pump it is recommended that some type of flow indicating device
be installed to measure water flow rates and be appropriate for the output of the pump.
Contact your distributor or sales representative for further information.
Head Loss / Over Pressure Protection / Back Pressure-Anti-Siphon Valve:

• Milton Roy metering pumps are positive displacement. Head loss is not applicable to the
pump.
• To ensure safe operation of the pump, it is recommended that some type of safety / pressure
relief valve be installed to protect the piping and other system components from failing due
to excessive pressure.
• If you are pumping downhill or into low or no system pressure, a back pressure / anti-siphon
device should be installed to prevent over pumping or siphoning.Contact your distributor or
sales representative for further information.
Additional Operation and Installation Instructions for 316SS or PVC Liquid Ends:
• Application of this pump to swimming pool / spas only evaluated to NSF / ANSI 50.
• There is a potential for elevated chemical concentration during periods of no flow, for
example, during backwash in the system. Steps, such as turning the pump off, should be
taken during operation or installation to prevent this. See your sales representative or
distributor about other external control options to help mitigate this risk.
• Liquid Compatibility CAUTION: Determine if the materials of construction included in the
liquid handling portion of your pump are adequate for the solution (chemical) to be pumped.
ALWAYS wear protective clothing, face shield, safety glasses and gloves when working on
or near your metering pump. Additional precautions should be taken depending on the
solution being pumped. Refer to SDS precautions from your solution supplier. Reference a
Milton Roy Material Selection Chart for aid in selecting appropriate material of construction
for fluids of your specific metering pump. Contact your sales representative or distributor for
further information.
2 Instruction, Operations & Maintenance Manual

GENEREAL PRECAUTIONS FOR ALL PUMPS
The following precautions should be taken when working with metering pumps.
Please read this section carefully prior to installation.
Protective Clothing
ALWAYS wear protective clothing, face shield, safety glasses and gloves when working on or
near your metering pump. Additional precautions should be taken depending on the solution
being pumped. Refer to Material Safety Data Sheets for the solution being pumped.
Hearing Protection
It is recommended that hearing protection be used if the pump is in an environment where the
timeweighted average sound level (TWA) of 85 decibels is exceeded.
(as measured on the A scale slow response).
Electrical Safety
• Remove power and ensure that it remains off while maintaining pump.
• DO NOT FORGET TO CONNECT THE PUMP TO EARTH.
• Electric protection of the motor (Thermal protection or by means of fuses) is to correspond
to the rated current indicated on the motor data plate.
Liquid Compatibility
Verify if the materials of construction of the wetted components of your pump are
recommended for the solution (chemical) to be pumped.
Pumps Water “Primed”

All pumps are tested with water at the factory. If your process solution is not compatible with
water, flush the Pump Head Assembly with an appropriate solution before introducing the
process solution.
Plumbing and Electrical Connections

Always adhere to your local plumbing and electrical codes.
Line Depressurization
To reduce the risk of chemical contact during disassembly or maintenance, the suction and
discharge lines should be depressurized before servicing.
Over Pressure Protection

To ensure safe operation of the system, it is recommended that some type of safety /
pressure relief valve be installed to protect the piping and other system components from
damage due to over-pressure.
Lifting
This manual should be used as a guide only - Follow your company’s recommended lifting
procedures. It is not intended to replace or take precedence over recommendations, policies
and procedures judged as safe due to the local environment than what is contained herein.
Use lifting equipment that is rated for the weight of the equipment to be lifted.
Instruction, Operations & Maintenance Manual 3

TABLE OF CONTENTS
1.0 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.1 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2 PRINCIPLE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3 GENERAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.0 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4 MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5 DRIP COLLECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.6 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.6.1 NPSH Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.6.2 General Piping Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.6.3 Suction Piping Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.6.4 Discharge Piping Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.7 VALVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.7.1 Back Pressure Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.7.2 Pulsation Dampeners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.7.3 Shut-off Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.8 ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.0 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1 START-UP PROCEDURES AND CHECKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2 CHECKING THE ELECTRICAL CONNECTION OF THE MOTOR . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3 START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4 CAPACITY CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.0 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1 PREVENTATIVE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.2 RETURNING PUMPS TO THE FACTORY FOR REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.3 ROUTINE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.4 SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.4.1 Size D2 Liquid Ends - PVC, PVDF, Polypropylene, Polymer and H2SO4 . . . . . . . . . . . . . . . . . . . . . 22
4.4.2 Size D2 Liquid Ends - PVC, PVDF, Polypropylene, Polymer, H2SO4 and Slurry . . . . . . . . . . . . . . . 22
4.4.3 Size D2 and D4 Liquid Ends - Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.4.4 Size D7 and D8 - PVC, PVDF, Polypropylene, H2SO4, Polymer and Slurry Liquid Ends . . . . . . . . . 23
4.4.5 Size D7 and D8 - Stainless Steel Liquid Ends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.5 CORRECTIVE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.5.1 Check Valve Replacement: Liquid Ends D2 and D4 - PVC, PVDF, H2SO4 and Polypropylene . . . . 25
4.5.2 Check Valve Replacement: Liquid End Sizes D2 and D4 - Polymer . . . . . . . . . . . . . . . . . . . . . . . . 25
4.5.3 Check Valve Replacement: Liquid End Sizes D2 and D4 - Metallic . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.5.4 Check Valve Replacement: Liquid End Sizes D2 and D4 - Slurry . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.5.5 Replacement of Ball, Seat and Seal: Liquid End D7 and D8 - PVC, PVDF, H2SO4 and
Polypropylene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4.5.6 Check Valve Replacement: Liquid End Size D7 and D8 - Polymer . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.5.7 Check Valve Replacement: Liquid End Size D7 and D8 - Slurry . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.5.8 Check Valve Replacement: Liquid End Size D7 and D8 - Stainless Steel . . . . . . . . . . . . . . . . . . . . 28
4.6 DIAPHRAGM AND OIL SEAL BELLOWS REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.6.1 Diaphragm Replacement: Liquid End Size D2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.6.2 Diaphragm Replacement: Liquid End Size D4, D7 and D8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.7 OIL SEAL BELLOWS REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.8 RESTARTING THE PUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.0 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.1 PARTS LIST FOR DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.2 PARTS LIST FOR D2 PLASTIC LIQUID END PVC, PVDF, BLACK POLY, H2SO4 AND
POLYMER-NPT / PVC, PVDF AND BLACK POLY-TUBING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5.3 PARTS LIST FOR D2 METALLIC LIQUID END STAINLESS STEEL-NPT . . . . . . . . . . . . . . . . . . . . . 36
5.4 PARTS LIST FOR D4 METALLIC LIQUID END STAINLESS STEEL-NPT . . . . . . . . . . . . . . . . . . . . . 42
5.5 PARTS LIST FOR D4 PLASTIC LIQUID END PVC, PVDF, BLACK POLY, H2SO4, SLURRY AND
POLYMER- NPT / PVC, PVDF, BLACK POLY AND H2SO4-TUBING . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.6 PARTS LIST FOR D7 AND D8 PLASTIC LIQUID END PVC-NPT / TUBING, PVDF-NPT, BLACK
POLY-NPT, POLYMER-NPT, SLURRY-NPT & H2SO4-NPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.7 PARTS LIST FOR D7 AND D8 316SS-NPT LIQUID END . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
5.8 LEAK DETECTION PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.0 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
LIST OF ILLUSTRATIONS
FIGURE 1. Pump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
FIGURE 2. Stroke Control Operating Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FIGURE 3. MacRoy® D Dimensional Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FIGURE 4. Typical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
FIGURE 5. General Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
FIGURE 6. Drive Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
FIGURE 7. Diaphragm Assemblies By Liquid End Size and Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FIGURE 8. Drive Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
FIGURE 9. D2 Plastic Liquid End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
FIGURE 10. D2 Metallic Liquid End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
FIGURE 11. D4 Metallic Liquid End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FIGURE 12. D4 Plastic Liquid End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
FIGURE 13. D7 & D8 Plastic Liquid End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
FIGURE 14. D7 & D8 316SS Liquid End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
FIGURE 15. Leak Detection Switch and / or Gauge (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
FIGURE 16. Double Diaphgram, D4 Pressure Type Configured (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
FIGURE 17. Double Diaphgram, D7 & D8 Pressure Type Configured (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . 54

MACROY® D PUMP MODEL NUMBER AND OPTIONS
Connections
Double Dia-
Liquid End
Liquid End
Frame and
Counting
Capacity
Stroking
Material
phragm
Control
Stroke
Speed
Motor
Base
Frame and Liquid End (D Frame) Connections
Code Description Code Description
D2 0.3 mL/stroke P NPT
D4 4.4 mL/stroke T Tubing
D7 18 mL/stroke B Outgassing Liquid Applications (NPT)
D8 42 mL/stroke C Outgassing Liquid Applications (Tubing)
Stroking Speed Capacity Control
1 43 SPM M4 Manual
2 86 SPM E1 4-20ma, NEMA 4 115 VAC
6 120 SPM E2 4-20ma, NEMA 4 230 VAC
3 173 SPM EA 4-20ma, Ex Prf 115 VAC
8 180 SPM @1450 RPM EB 4-20ma, Ex Prf 230 VAC
Motor Double Diaphragm
X NEMA 56C Mount Less Motor N None
8 115/230 VAC, 60 Hz,1 PH, 1725 RPM D Double Diaphragm
9 115/230 VAC, 50 Hz,1 PH, 1450 RPM 3 Double Diaphragm w/Gauge
Double Diaphragm w/NEMA 4 Rupture
J 230/460 VAC, 60 Hz, 3 PH, 1725 RPM 4
Detection
Double Diaphragm w/NEMA 7 Rupture
L 220/380 VAC, 50 Hz, 3 PH, 1450 RPM 7
Detection
M IEC 71 Frame F130 Less Motor
P DC VSD & Motor
Liquid End Material Base
2 PVDF N None
4 Black Polypropylene (UV Stable) 1 Simplex Optional Base
7 316SS
8 PVC Stroke Counting
P Polymer Service Code Description
L Slurry Applications N None
N H2SO4 Applications
A Acrylic

MacRoy® D Capacity / Pressure
English Units Metric Units
GPH @ GPH @
Liquid SPM @ Liquid SPM @
Max PSI Max Max Bar Max
End End
60 50 60 50 PSI 60 50 60 50 Bar
Codes Codes
Hz Hz Hz Hz Hz Hz Hz Hz
43 36 0.18 0.15 43 36 0.7 0.6
86 72 0.35 0.29 86 72 1.3 1.1
2 175 2 12
120 102 0.48 0.40 120 102 1.8 1.5
173 144 0.7 0.58 173 144 2.6 2.2
43 36 3.0 2.5 43 36 11.4 9.5
86 72 6.6 5.5 86 72 25 21
4 150 4 10
120 102 10 6.9 120 102 38 26
173 144 12 12 173 144 45 45
43 36 13 10 43 36 49 38
86 72 25 21 86 72 95 79
7 100 7 7
120 102 34 28 120 102 129 106
173 144 50 42 173 144 189 159
43 36 31 26 43 36 117 98
86 72 57 47 86 72 216 178
8 75 8 5
120 102 87 72 120 102 329 273
173 144 127 106 173 144 481 401
NOTE:
1. All Capacities are based on maximum pressure. For operation at reduced pressures, add 1% flow
for every 25 psi (1.7 bar) decreased in pressure.
2. Motor requirements: 1/4 Horsepower or 0.25KW

SECTION 1 - DESCRIPTION
1.1 GENERAL INFORMATION The basic pump components as illustrated in
The MacRoy D is a reciprocating, chemical
® Figure 1 are:
dosing pump capable of producing flows up to • a drive device comprising a motor (1).
115 gph (430 liters per hour) at pressures
• a mechanical assembly (2).
up to 175 psi (12 bar). These pumps feature a
mechanically actuated diaphragm liquid end, which • a liquid end (3).
eliminates the need for flow-restricting contour An elastomeric bellows provides a leak-tight seal
plates, and a stroke adjustment mechanism based between the mechanical assembly and the liquid
on the variable eccentric principle instead of the end.
traditional lost-motion design. It is designed for Capacity adjustment is manually controlled by
industrial service and offers an accuracy of ±1% a stroke adjustment knob (4).
of full rated flow between 10% and 100% of its
flow range.
7 2
6
5
Figure 1. Pump Assembly
1 Motor 5 Liquid End Mounting Assembly

2 Mechanical Assembly 6 Check Valve Assembly (Suction)
3 Liquid End 7 Check Valve Assembly (Discharge)
4 Stroke Adjustment Knob 8 Stroke Lock Knob

1.2 PRINCIPLE OF OPERATION t 0% capacity setting, the connecting rod axis (B)
A
is aligned with the gear axis (A) and no movement
Drive Assembly (See Figure 2)
of the connecting rod takes place. At 100%
The pump consists of two major assemblies; the
capacity setting, an eccentricity exists between
drive and the liquid end. Pump delivery is a function
the connecting rod axis (B) and the gear axis (A)
of the drive’s stroke rate, liquid end size and stroke
which results in linear movement of the connecting
length. Stroke length can be increased while the
rod and resulting pumpage.
pump is running by counterclockwise turning of
Drive parts (See Figure 8 for limited drive parts
the stroke adjustment knob. The drive assembly
available) are no longer sold by Milton Roy.
works on the principle of a variable eccentric.
When drive parts are found to be bad a complete
The rotational motion of the motor is transmitted by
new painted pump body with all gears, stroke
the worm (1) to the worm gear (2) which is linked
controls etc. can be purchased from Milton Roy.
to an eccentric system (3). The eccentric system
The customer will only need to mount the liquid
then converts the rotary gear motion into linear
end motor from the existing pump.
reciprocating motion of the connecting rod (4).
2
(A) (B)
3
4
Zero Stroke Setting
(A) (B)
(A) (B)
7
Suction Phase Discharge Phase
6
Setting to Maximum Stroke 8
Figure 2. Stroke Control Operating Principle

1 Worm 5 Diaphragm
Stroke: two times the distance
2 Worm Gear 6
between (A) and (B)
3 Eccentric 7 Position at rear neutral point
4 Connecting Rod 8 Position at forward neutral point

Mechanically-Actuated Diaphragm Liquid End 1.3 GENERAL SPECIFICATIONS
(See Figure 2)
The diaphragm assembly (5) is mechanically Flow Rate Up to 115 GPH (430 L/H)
linked to the connecting rod (4) and has the same Pressure Up to 175 PSIG (12 BAR)
reciprocating motion. As the diaphragm starts back Liquid End Mechanically-Actuated
on the suction stroke, the pressure immediately Type Diaphragm
drops inside the liquid end. When the pressure Drive Type Variable Eccentric
in the liquid end drops below the suction line ±1% of pump full rated capacity
Steady State
pressure, the suction ball check is “pushed” upward between 10% and 100% of rated
Accuracy
and the process fluid in the suction line flows capacity.
into the liquid end chamber (diaphragm head). Lockable stroke adjustment knob
Capacity
When the suction stroke ends, the diaphragm Adjustment
is adjustable from 0% to 100%
movement momentarily stops and the pressure while pump is running.
in the liquid end equalizes with the pressure in Drive is lubricated in an oil bath
Lubrication
the suction line causing the suction ball check to (Mobil SHC 629, 1 Quart).
reseat.
Temperature
NOTE: 122º F (50ºC) Maximum
It is important that the pressure in the liquid Ambient and
end remain above the vapour pressure of the Liquid: 14º F (-10ºC) Minimum
process fluid during the suction stroke. If the
fluid pressure drops below the vapour pressure,
cavitation will occur which will have a negative 6.6 Ft (2 meters) of water
impact on the performance of the pump. If you column maximum
suspect the possibility of cavitation, contact Suction Lift
11.5 psia minimum internal
Milton Roy for assistance. pressure (3.2 psi maximum
As the diaphragm starts forward on the discharge vacuum)
stroke the pressure immediately rises inside the Paint Powder Coating
liquid end. When the liquid end pressure rises 38 lb (17.2 kg) Without EEC
Weight
above the discharge line pressure, the discharge 48 lb (21.8 kg) With EEC
ball check is “pushed” upward and the process
fluid in the liquid end flows into the discharge line.
When the discharge stroke ends, the diaphragm
momentarily stops again. The pressure in the liquid
end equalizes with the discharge line pressure and
the discharge ball check reseats. The cycle then
starts again.

SECTION 2 - INSTALLATION
2.1 UNPACKING If equipment is to be shipped directly from Milton

Pumps are shipped Free on Board factory (FOB) Roy into long term storage, contact Milton Roy to
or representative warehouse and the title passes arrange for factory preparation.
to the customer when the carrier signs for receipt Pump Drive
of the pump. In the event that damages occur 1. Remove motor and flood the gearbox
during shipment, it is the responsibility of the compartment (Item 2 in Figure 1) with a high
customer to notify the carrier immediately and to grade lubricating oil / rust preventative such as
file a damage claim. Carefully examine the shipping Mobile Oil Corporation product Mobilarma 524.
crate upon receipt from the carrier to be sure there Fill the compartment completely to minimize
is no obvious damage to the contents. Open the air space and water vapour condensation.
crate carefully so accessory items fastened to the After storage, drain this material and refill the
inside of the crate will not be damaged or lost. equipment with the recommended lubricant for
Examine all material inside the crate and check equipment commissioning.
against packing list to be sure that all items are
2. Brush all unpainted metal surfaces with
accounted for and intact.
multipurpose grease (NLGI grade 2 or 3).
2.2 STORAGE Store these unattached.
Short Term Storage (Less than 6 Months) Electrical Equipment

It is preferable to store the material under a shelter 1. Motors should be prepared in the manner
in its original package to protect it from adverse prescribed by their manufacturer. If information
weather conditions. In condensing atmospheres, is not available, dismount and store motors as
follow the long term storage procedure. indicated in step 3 below.
2. Dismount electrical equipment
Long Term Storage (Longer than 6 Months)
(including motors) from the pump.
The primary consideration in storage of pump
3. For all electrical equipment, place packets of
equipment is to prevent corrosion of external and
Vapour Phase Corrosion Inhibitor (VPCI) inside
internal components. This corrosion is caused
of the enclosure, then place the entire enclosure,
by natural circulation of air as temperature of the
with additional packets, inside a plastic bag.
surroundings change from day to night, day to day,
Seal the bag tightly closed. Contact Milton Roy
and from season to season. It is not practical to
Service Department for recommended VPCI
prevent this circulation which carries water vapour
materials.
and other corrosive gasses, so it is necessary to
protect internal and external surfaces from their
effects to the greatest extent possible.
When the instructions given in this section are
completed, the equipment is to be stored in a
shelter; protected from direct exposure to weather.
The prepared equipment should be covered with a
plastic sheet or a tarpaulin, but in a manner which
will allow air circulation and prevent capture of
moisture. Equipment should be stored 12 inches
or more above the ground.

2.3 SAFETY PRECAUTIONS 2.5 DRIP COLLECTION
WHEN INSTALLING, OPERATING, In the event of a failure of the diaphragm or oil
AND MAINTAINING THIS
seal bellows, provisions need to be made to
MACROY® D PUMP, KEEP SAFETY CONSIDERATIONS
FOREMOST. USE PROPER TOOLS, PROTECTIVE CLOTHING, contain the process fluid or pump oil. This is
AND EYE PROTECTION WHEN WORKING ON THE EQUIPMENT particularly important when handling fluids which
AND INSTALL THE EQUIPMENT WITH A VIEW TOWARD may be harmful to plant personnel. To collect fluid
ENSURING SAFE OPERATION. FOLLOW THE INSTRUCTIONS
in the event of a diaphragm or oil seal rupture,
IN THIS MANUAL AND TAKE ADDITIONAL SAFETY MEASURES
APPROPRIATE TO THE LIQUID BEING PUMPED. BE (See Figure 1) position a tray under the plain hole
EXTREMELY CAREFUL IN THE PRESENCE OF HAZARDOUS located at the bottom of the liquid end mounting
SUBSTANCES (E.G., CORROSIVES, TOXINS, SOLVENTS, assembly (5). For D7 or D8 pumps, position tray
ACIDS, CAUSTICS, FLAMMABLES ETC).
under tube fitting located at bottom of liquid end
THE PERSONNEL RESPONSIBLE mounting assembly. Alternatively, a tube may be
FOR INSTALLATION, OPERATION installed onto this tube fitting to drain any leakage
AND MAINTENANCE OF THIS EQUIPMENT MUST BECOME to a suitable container.
FULLY ACQUAINTED WITH THE CONTENTS OF THIS MANUAL.
ANY SERVICING OF THIS EQUIPMENT MUST BE CARRIED OUT
WHEN THE UNIT IS STOPPED AND ALL PRESSURE HAS BEEN
BLED FROM THE LIQUID END. SHUT-OFF VALVES IN SUCTION
AND DISCHARGE SIDES OF THE LIQUID END SHOULD BE
CLOSED WHILE THE UNIT IS BEING SERVICED. ACTIONS
SHOULD BE TAKEN TO ELIMINATE THE POSSIBILITY OF
ACCIDENTAL START-UP WHILE SERVICING IS TAKING PLACE.
A NOTICE SHOULD BE POSTED BY THE POWER SWITCH TO
WARN THAT SERVICING IS BEING CARRIED OUT ON THE
EQUIPMENT. SWITCH OFF THE POWER SUPPLY AS SOON AS
ANY FAULT IS DETECTED DURING OPERATION (EXAMPLES:
ABNORMALLY HIGH DRIVE TEMPERATURE, UNUSUAL NOISE
AND DIAPHRAGM FAILURE).
2.4 MOUNTING
Support the pump firmly in a level position on a
solid, vibration-free foundation. The pump should
preferably be positioned with the base above floor
level to protect the pump from wash downs and
to provide easier access for service. Be sure to
allow enough space around the pump for easy
access during maintenance operations and pump
adjustments. MacRoy® D pumps are provided with
mounting holes to accommodate anchor bolts.
Refer to Figure 3 for mounting hole dimensions.
Pumps installed outdoors should be protected by
a shelter.

LE Size CONN. A B C
D2 PLASTIC-NPT(1/4" M) 5.53 4.5 10.5
D2 PLASTIC-TUBE(1/4") 7.53 4.5 10.5
D2 METALLIC-NPT(1/4" M) 6.50 4.5 10.5
D4 PLASTIC-TUBE(1/2") 7.53 4.5 10.5
D4 PLASTIC-NPT(1/4" M) 5.53 4.5 10.5
D4 METALLIC-NPT(1/2" M) 6.80 4.5 10.5
D7/8 PLASTIC-NPT(1/2" F) 9.94 6.2 13.0
D7/8 METALLIC-NPT(1/2" F) 10.25 6.2 13.0
M = Male; F = Female All dimensions in inches.
Shown with standard 1/4 HP, TEFC, NEMA 56 Motor
1.26 1.57
DISCHARGE:
SEE CHART
FOR LE SIZE 17.00
AND CONN
3.88
.50
3.33 4.47 MAX. B
1.14 C MAX.
10 MAX.
SUCTION:
SEE CHART 4.15
Ø0.44
FOR LE SIZE
AND CONN
4.15
6.30
Figure 3. MacRoy® D Dimensional Outline (1022784000)

4
6 4
3
5
6
1
5
3 1
4
6
1 9
3
7 8
Figure 4. Typical Installation

1 Tank 5 Injection Nozzle
2 Foot Valve (with Filter) 6 Shut-off Valve
3 Metering Pump 7 Filter
4 Process Piping 8 Pulsation Damper
5 Bleed Valve - -

2.6 INSTALLATION To minimize viscous flow losses when handling

Figure 4 displays typical installations viscous liquids, it may be necessary to use suction
(both correct and incorrect). Figure 5 illustrates piping up to four times larger than the size of
the recommended piping and accessories in a the suction connection on the pump. If in doubt,
metering pump installation. contact your nearest Milton Roy representative to
determine the necessary pipe size.
As illustrated in the upper right portion of Figure 4,
there must be no swan-necks or stagnant volumes 2.6.2 General Piping Considerations
in the suction line. In this illustration, the loop at the Use extreme care in piping to plastic liquid end
top of the tank forms an air trap. Eventually, air or pumps with rigid pipe such as PVC. If excessive
gases will bubble out of solution and accumulate in pipe stress or vibration is unavoidable, flexible
the trap leading to a loss of prime condition. connections are recommended.
2.6.1 NPSH Considerations Use piping materials that will resist corrosion by
Size piping to accommodate peak instantaneous the liquid being pumped. Use care in selecting
flow. Because of the reciprocating motion of the materials to avoid galvanic corrosion at pump liquid
pump diaphragm, peak instantaneous flow is end connections.
approximately equal to 5 times the average flow. Use piping heavy enough to withstand maximum
For example, a pump rated for 16 gph (61 L/hr.) pressures. Remove burrs, sharp edges, and debris
requires piping sufficient for 5 x 16 gph, or 80 gph from inside piping. Blow out all pipelines before
(303 L/hr.). making final connections to pump.
Figure 5. General Piping

Because vapour in the liquid end will cause A strainer should be used in the suction line
inaccurate pump delivery, piping should be sloped to prevent foreign particles from entering the
up from pump suction check to the supply tank to liquid end. This and any other measures which
prevent formation of vapour pockets. prevent debris from entering and fouling the
When pumping suspended solids (such as slurries), liquid end check valves will give increased
install plugged crosses at all 90° line turns to permit maintenance free service. Check strainer frequently
line cleaning without dismantling piping. to prevent blockage which could lead to cavitation.
Keep suction piping as short and straight as
See Figure 5 for a typical recommended pump
possible.
installation scheme.
Piping size should be larger than the liquid end
2.6.3 Suction Piping Considerations suction fitting to prevent pump starvation.
It is preferable to have the suction of the pump
If long suction lines are unavoidable, install a stand
flooded by locating the liquid end below the lowest
pipe near the pump in the suction line.
level of the liquid in the supply tank.
Suction piping must be absolutely airtight to ensure
To minimize the chances of a loss-of-prime
accurate pumping. After installation, test suction
condition, the pump should be installed as close
piping for leaks with air and soap solution.
as possible to the supply vessel.
Avoid negative suction pressure conditions 2.6.4 Discharge Piping Considerations
(suction lift), as such conditions adversely affect Install pipe large enough to prevent excessive
metering accuracy. A lift of 6.6 feet (2 meters) of pressure losses on the discharge stroke of the
water column is the maximum permissible suction pump. Maximum pressure at the discharge fitting
lift. on the liquid end must be kept at or below the rated
pressure (shown on the pump nameplate).
MacRoy® D pumps are designed to operate with
process liquid supplied at or above atmospheric The pump will not deliver a controlled flow unless
pressure. Although these pumps can move the discharge line pressure is 10 psi (0.7 bar)
liquids supplied at less than atmospheric pressure greater than the suction line pressure. One way
(suction lift), in these negative pressure applications, to create an artificial pressure is the installation
it is important that all connections be absolutely of a back pressure valve. (Please contact your
drip free and vacuum tight, and that a foot valve Milton Roy representative for recommendations
be installed at the bottom of the suction line to increase back pressure in slurry applications).
(see upper left illustration of Figure 4). When pumping water treatment chemicals directly
When pumping a liquid near its boiling point, into boiler drums, use one liquid end assembly
provide enough suction head to prevent the liquid for each boiler drum. Discharging into a manifold
from “flashing” into vapour when it enters the pump having the slightest pressure difference between
liquid end on the suction stroke. its several discharge connections can diminish
metering accuracy as the outlet with the lowest
If possible, use metal or plastic tubing for the
pressure will receive more liquid than the other
suction line because tubing has a smooth inner
outlets.
surface and can be formed into long, sweeping
bends to minimize frictional flow losses.

2.7 VALVES 2.7.3 Safety Valves and Priming Valves

Motor-driven positive displacement pumps can
2.7.1 Back Pressure Valves
develop excessive discharge pressures long
All metering pumps are prone to overpumping
before thermal overload devices interrupt the motor
(excessive output) at low discharge pressures.
electrical circuit. To prevent a blocked discharge
To prevent this condition from occurring, it
line from causing damage to the pump, piping or
is necessary to maintain approximately
process equipment, install a safety valve in the
10 psi (0.7 bar) back pressure against the pump.
pump discharge line. This valve is designed and
This can be accomplished through the installation
sized to handle system flow rates and pressures
of a back pressure valve in the discharge line.
safely while resisting corrosion by the process
Typically, the valve should be located near the
liquid.
pump. However, back pressure valves for large
pumps with long and extremely small discharge To aid in pump start-up, it is advisable to install a
lines may have to be installed near the point of priming valve on the discharge side of the liquid
discharge into the process (to minimize siphoning end.
tendencies). 2.7.4 Shut-off Valves
2.7.2 Pulsation Dampeners Provide shut-off valves in both suction and
An accumulator, surge chamber, surge suppressor discharge lines next to the pump. Locate discharge
or pulsation dampener should be used with the line shut-off valve downstream from the inlet
back pressure valve in the discharge line to connection of the safety valve. Figure 5 shows
absorb the flow peaks between the pump and recommended valve locations.
the back pressure valve. Without the pulsation
2.8 ELECTRICAL CONNECTIONS
dampener the valve mechanism will snap open
OPERATION WITH THE WRONG
and close with the surge from each pump stroke. MOTOR ROTATION MAY DAMAGE
The pulsation dampener will allow the back THE PUMP AND MOTOR AND VOID THE WARRANTY. DO NOT
pressure valve to oscillate about a partly-closed FORGET TO CONNECT THE EARTH TERMINAL ON THE MOTOR
TO THE EQUIPMENT EARTH CONDUCTOR.
position, thus minimizing wear on the valve.
Discharge line pulsation dampeners offer the Ensure that the electrical supply matches
further advantage of limiting the flow and pressure the pump motor nameplate characteristics.
variations characteristic of this kind of pump. Connect the motor in accordance with the
Installing a properly sized pulsation dampener instructions and connection diagrams on the motor
will improve pump performance and may reduce (or in the motor terminal box).
system costs dramatically by permitting the NOTE:
substitution of smaller piping. Please contact Milton Before operating the pump, check the direction
Roy for further information on pulsation dampeners. of rotation of the motor to be sure it matches the
direction of the arrow on the motor fan cover
(rotation should be clockwise when viewed from
the top of the motor).
The electrical protection installed for the motor
(fuse or thermal protection) must be suitable for
the motor’s rated current.

SECTION 3 - OPERATION
3.1 START-UP PROCEDURES AND Once all the checks and procedures described
CHECKS above have been carried out, start the pump.
Check that the pump is secured to its support. Conduct a visual and audio check of the pump
If oil was previously removed for any reason, make (in particular, listen for the presence of any
sure pump drive has the correct volume (1 quart) “suspicious” noises).
of oil (Mobil SHC 629). Make sure that the stroke adjustment knob is
Make sure all isolation valves installed on the unlocked.
suction and discharge lines are open. If the Gradually increase the capacity until liquid can be
discharge line is equipped with an injection nozzle seen flowing from the priming valve. If no priming
or a back-pressure valve, open the priming valve for valve is in place, when the liquid end is primed,
discharge (if there is no priming valve, disconnect the discharge check valves can be heard to be
the discharge pipe). This allows for verification that operating (should hear a clicking noise caused by
liquid is present in the liquid end when the pump is movement of check valve balls). When liquid end is
installed in flooded suction condition. If the pump primed, stop the pump and close the priming valve.
is installed in a suction lift condition, this allows for
Adjust the pump to the desired capacity. Lock the
priming of the pump during start-up.
stroke adjustment knob (Item 8 in Figure 1).
Make sure that pump is set at 0% capacity.
3.4 CAPACITY CALIBRATION
3.2 CHECKING THE ELECTRICAL
CONNECTION OF THE MOTOR After the first 12 hours of operation, the pump
Start up the pump to check the motor’s direction may be tested and calibrated to find the exact
of rotation. It must comply with that indicated pump capacity under specific operating conditions.
by the arrow marked on the motor fan cover Usually, calibrating the pump at only 100, 50 and
(clockwise as viewed from the top of the motor). 10 percent capacity settings is enough to indicate
If the rotation is incorrect, refer to Section 2.8 pump performance throughout the adjustment
Electrical Connections. range.
The pump can be calibrated by measuring the
3.3 START-UP decrease in liquid level pumped from a calibrated
FAILURE TO CHECK TORQUE vessel. This method is recommended for hazardous
ON NON-METALLIC HEAD liquids because it eliminates operator contact with
BOLTS PRIOR TO STARTUP AND AFTER ONE WEEK OF the liquid. Calibration columns are available for
OPERATION MAY EXPOSE OPERATING PERSONNEL TO
HAZARDOUS LIQUIDS.
convenient and accurate calibration of the pump.
Contact your local Milton Roy representative for
Check the torque on all non-metallic head bolts
more information.
prior to startup. Recheck torque on all non-metallic
head bolts after pump has been operating for one FOR SAFETY REASONS, A
week. Torque the head assembly screws in a CHECK VALVE IS RECOMMEND-
ED FOR USE IN THE DISCHARGE LINE NEAR THE POINT
crosswise pattern as follows:
WHERE THE LINE ENTERS A HIGH-PRESSURE PROCESS
a. Liquid End Size D2 and D4 to 45 inch VESSEL.
pounds.
b. Liquid End Size D7 and D8 to 90 inch
pounds.

SECTION 4 - MAINTENANCE
4.1 PREVENTATIVE MAINTENANCE 4.2 RETURNING PUMPS TO THE
FACTORY FOR REPAIR
Drive
Pumps can not be accepted for repair without a
Initially, change the oil in the pump drive
Return Material Authorization. Pumps should be
assembly after the first 1000 hours of operation.
clearly labeled to indicate the liquid being pumped.
Thereafter, change drive oil on an annual basis or
Process liquid should be flushed from the pump
after every 5000 hours of operation.
liquid end and oil should be drained from the pump
The drive should be refilled with 1 quart of Mobil housing before the pump is shipped.
SHC 629:
NOTE:
Viscosity @ 100º F = 726 SSU United States of America Federal law prohibits
handling of equipment that is not accompanied
Viscosity Index = 149 by an OSHA Safety Data Sheet (SDS).
ISO Grade = 150 A completed SDS must be packed in the
shipping crate with any pump shipped for
Diaphragm Assembly repair. These safety precautions will aid the
troubleshooting and repair procedure and
The MacRoy® D diaphragm should be replaced
preclude serious injury to repair personnel from
annually or every 5000 hours of operation to avoid hazardous residue in pump liquid end. A Safety
the possibility of failure. Refer to the instructions Data Sheet must accompany all returns.
in Section 4.6 Diaphragm and Oil Seal Bellows All inquiries or parts orders should be addressed to
Replacement. your local Milton Roy representative or distributor.
Oil Seal Bellows Representatives can be found on our website
The MacRoy® D oil seal bellows should only be www.miltonroy.com
replaced if failure of the bellows has occurred.
4.3 ROUTINE MAINTENANCE
Oil seal bellows replacement requires the removal
of the diaphragm assembly, so it is recommended Milton Roy MacRoy ® D pumps are carefully
that the oil seal and diaphragm assembly be designed, manufactured and assembled to give
replaced at the same time. Refer to the instructions reliable service with minimal maintenance. However,
in Section 4.6 Diaphragm and Oil Seal Bellows a weekly maintenance check is recommended to
Replacement. confirm proper operation of the pump.
Check Valves Visual Check of Seal Integrity of Mechanical

Assembly, Figure 6.
As in the case of the diaphragm, Milton Roy
Check for leaks in the following components.
recommends that check valve balls, seats, gaskets
If leaks exist, contact Milton Roy for assistance.
and O-rings be replaced on an annual basis or
every 5000 hours of operation. If highly corrosive 1. Motor flange: If leaking, replace motor flange
material (acids and slurries etc.) is being pumped, sealing gasket (Item 11 in Figure 6).
more frequent replacement may be required. 2. Stroke adjustment knob: If leaking, replace
Complete instructions for replacement of worn stroke adjustment seal (Item 160 in Figure 6).
check valves are given in Section 4.5 Corrective
Maintenance.

346
347
342
130
170
340
190
150
200
11 10
320
322
510 206
310
205
360 140 330
50
332
121 60
110 160
120
111
19 102
20 140
335
100
101
150
Figure 6. Drive Assembly (10227280007)
ITEM ITEM ITEM

NOMENCLATURE NOMENCLATURE NOMENCLATURE
NO. NO. NO.
10 Housing 121 Gear Key 322 O-ring
11 Gasket 130 Retaining Ring 330 Stroke Adj. Knob
19 O-ring 140 Bearing 332 Screw
20 Oil Drain Plug 150 Retaining Ring 335 Sticker
50 Gear 160 Seal 340 Bearing
60 Connecting Rod 170 Stroke Adj. Screw 342 Worm
100 Male Eccentric 190 O-ring 346 Motor Coupling
101 Drive Shaft 200 Side Cover 347 Screw
102 Spring Pin 205 Screw 360 Set Screw
110 Female Eccentric 206 Washer 510 Breather Plug
111 Spring Pin 310 Stroke Lock
120 Stroke Adjust Key 320 Stroke Lock

Checking the Pump Capacity 4.4 SPARE PARTS
Assuming the pump has been calibrated as The following spare parts should be stocked for
described in Section 3, the capacity can be checked each pump to prevent serious delays in repairs.
by shutting the valve from the supply vessel and (Refer to Figures 7 thru 15).
opening the valve from the calibration column to the
suction side of the liquid end. Measure the volume Parts orders must include the following:
of pumped liquid for a given period of time at the 1. Quantity required.
various settings. 2. Part number.
If a calibration column is not installed in the suction
3. Part description.
piping, place the foot valve (or suction line) in
a calibrating chamber (graduated reservoir). 4. Pump serial number (found on nameplate).
Measure the volume of pumped liquid for a given 5. Pump product code (found on nameplate).
period of time at the various settings.
NOTE:
Occurrence of Leak From Detection Ports Always include the serial number and product
Determine whether the product collected at the code in all correspondence regarding the unit.
detection port in the liquid end mounting assembly
is lubricating oil or the pumped fluid.
If the product is pumped fluid, the diaphragm has
failed. If the product is lubricating oil, the oil seal
bellows has failed. Proceed with its replacement
(see Section 4.6 Diaphragm and Oil Seal Bellows
Replacement).
260
261 274
240
252 271
250
270
D2 D4 (Plastic)
260
260
274 274
251
271 271
240
240
250 250
253 270
270
D7 and D8 D4 (316SS)
Figure 7. Diaphragm Assemblies By Liquid End Size and Material

4.4.1 Size D2 Liquid Ends - PVC, PVDF, 4.4.2 Size D4 Liquid Ends - PVC,
Polypropylene, Polymer and H2SO4. PVDF, Polypropylene, Polymer, H2SO4
and Slurry.
Liquid End Kit for D2 PVC / PVDF / Polypropylene
RPM 099, Includes: Liquid End Kit for D4 PVC / PVDF / Polypropylene
1 each, Diaphragm: Item 260 in Figure 9. RPM 102, Includes:
1 each, Oil Seal Bellows: Item 70 in Figure 9. 1 each, Diaphragm: Item 260 in Figure 12.
2 each, O-Ring: Item 419, Seat: Item 420, Ball: 1 each, Oil Seal Bellows: Item 70 in Figure 12.
Item 422, Cartridge: Item 426 and Washer: Item 1 each, PTFE Washer: Item 274 in Figure 12.
427 in Figure 9. 2 each, Cartridge Assembly: (P/N 36306) Included
in Kit.
Liquid End Kit for D2 Polymer RPM 196,
Includes: Liquid End Kit for D4 Polymer RPM 196,
1 each, Diaphragm: Item 260 in Figure 9. Includes:
1 each, Oil Seal Bellows: Item 70 in Figure 9. 1 each, Diaphragm: Item 260 in Figure 12.
2 each, O-Ring: Item 419, Seat: Item 420, Ball: 1 each, Oil Seal Bellows: Item 70 in Figure 12.
Item 422, Cartridge: Item 426, Washer: Item 427 1 each, PTFE Washer: Item 274 in Figure 12.
and Spring: Item 428 (Discharge Only) in Figure 9. 2 each, O-Ring: Item 419, Seat: Item 420, Ball: Item
Liquid End Kit for D2 H2SO4 Includes: 422, Fitting: Item 424, Cartridge: Item 426, Washer:
1 each, Diaphragm: Item 260 in Figure 9. Item 427 and Spring: Item 428 in Figure 12.
1 each, Oil Seal Bellows: Item 70 in Figure 9. Liquid End Kit for D4 H2SO4 NPT RPM 173,
2 each, O-Ring: Item 419, Seat: Item 420, Ball: Includes:
Item 422, Cartridge: Item 426 and Washer: Item 1 each, Diaphragm: Item 260 in Figure 12.
427 Figure 9. 1 each, Oil Seal Bellows: Item 70 in Figure 12.
Liquid End Kit for D2 PVC / PVDF Double 1 each, PTFE Washer: Item 274 in Figure 12.
Diaphragm RPM 161, Includes: 2 each, Cartridge Assembly: (P/N 39461) Included
1 each, Diaphragm: Item 260 in Figure 9. in Kit.
1 each, Oil Seal Bellows: Item 70 in Figure 9. Liquid End Kit for D4 H2SO4 Tubing RPM 174,
1 each, Diaphragm: Item 264 in Figure 15. Includes:
2 each, O-Ring: Item 419, Seat: Item 420, Ball: 1 each, Diaphragm: Item 260 in Figure 12.
Item 422, Cartridge: Item 426 and Washer: Item 1 each, Oil Seal Bellows: Item 70 in Figure 12.
427 in Figure 9. 1 each, PTFE Washer: Item 274 in Figure 12.
2 each, Cartridge Assembly: (P/N 39461) Included
in Kit and Coupling Nut: Item 428 in Figure 12.
Liquid End Kit for D4 Slurry RPM 212, Includes:
1 each, Diaphragm: Item 260 in Figure 12.
1 each, Oil Seal Bellows: Item 70 in Figure 12.
2 each, Check Valve Assembly: Item 425 in
Figure 12.

Liquid End Kit for D4 PVC / PVDF Double NOTE:
Diaphragm RPM 163, Includes: The check valves for the size D7 and D8-PVC,
1 each, Diaphragm: Item 260 in Figure 12. PVDF and Polypropylene liquid ends contain a
removable seat, which permits the replacement
1 each, Oil Seal Bellows: Item 70 in Figure 12. of the seat, O-ring and ball into a reusable valve
1 each, Diaphragm: Item 264 in Figure 15. body. The liquid end size D7 and D8-Stainless
Steel check valve has an integral ball seat,
1 each, PTFE Washer: Item 274 in Figure 12. which necessitates replacement of the entire
2 each, Cartridge Assembly.: (P/N 36306) Included check valve assembly.
in Kit.
4.4.4 Size D7 and D8 - PVC, PVDF,
NOTE: Polypropylene, H2SO4, Polymer and
Liquid end sizes D2 and D4 metallic check Slurry Liquid Ends
valves (except Slurry) are precision assembled
at the factory. Do not attempt to disassemble Liquid End Kit for D7/D8 PVC / PVDF / H2SO4 RPM
these cartridges. 135/105(PVC & Black PP) RPM 136/106(PVDF)
RPM 175/183(H2SO4), Includes:
4.4.3 Size D2 and D4 Liquid Ends - Stainles 1 each, Diaphragm: Item 260 in Figure 13.
steel 1 each, Oil Seal Bellows: Item 70 in Figure 13.
Liquid End Kit for D2/D4 316SS RPM 101/ 1 each, PTFE Seal Ring: Item 210 in Figure 13.
RPM 104, Includes:
2 each, Seat: Item 420, Ball: Item 422 in Figure 13.
1 each, Diaphragm: Item 260 in Figure 10/11.
4 each, O-ring: Item 419 in Figure 13.
1 each, O-ring: Item 253 in Figure 11 (D4 only).
Liquid End Kit for D7/D8 Polymer RPM 211/210,
1 each, PTFE Washer: Item 274 in Figure 11
Includes:
(D4 only).
1 each, Oil Seal Bellows: Item 70 in Figure 10/11.
1 each, PTFE Seal Ring: Item 210 in Figure 13.
Figures 10 and 11.
1 each, Spring: Item 422A in Figure 13.
Liquid End Kit for D2/D4 316SS Double
1 each, Poppet: Item 426A in Figure 13.
Diaphragm RPM 162/164, Includes:
2 each(D4) 1 each (D2), Diaphragm: Item 260 in 2 each, Seat: Item 420, Ball: Item 422 in Figure 13.
Figure 10/11. 4 each, O-ring: Item 419 in Figure 13.
1 each, Oil Seal Bellows: Item 70 in Figure 10/11. NOTE:
1 each, Diaphragm: Item 264 in Figure 15 Figure 13, Item 423 (Kit) contains the following:
(D2 only). • 1 each, Ball: Item 422.
1 each, O-ring: Item 253 in Figure 11 (D4 only)
• 1 each, Seat: Item 420.
1 each, PTFE Washer: Item 274 in Figure 11
(D4 only). • 2 each, O-rings: Item 419.

Figures 10 and 11.

Liquid End Kit for D7/D8 Slurry RPM 215, Check Valve Replacement:
Includes:
General
Before beginning work on the valve assemblies,
make sure the suction and discharge shut-off
1 each, PTFE Seal Ring: Item 210 in Figure 13. valves are closed and that pressure has been
4 each, O-ring: Item 419 in Figure 13. bled from the pump liquid end. When replacing
2 each, Check Valve Assembly: (P/N 60827) Item the valves, be sure to replace the valve O-rings.
425 in Figure 13. Pay close attention to the proper assembly and
orientation of the check valves as shown in each
4.4.5 Size D7 and D8 - Stainless Steel Liquid Liquid End figure. In the case of plastic check
Ends valves for liquid end size D7 and D8, be certain
Liquid End Kit for D7/D8 RPM 137/107, Includes: that the ball is placed on the sharp edge of the
1 each, Diaphragm: Item 260 in Figure 14. valve seat.
1 each, Oil Seal Bellows: Item 70 in Figure 14. BE SURE TO FOLLOW INSTRUC-
2 each, Check Valve Assembly: Item 425 in TIONS CAREFULLY AND REFER
TO THE APPROPRIATE FIGURE WHEN REASSEMBLING
Figure 14. CHECK VALVES. IF CHECK VALVE CARTRIDGES ARE
INSTALLED INCORRECTLY, ONE OF THE FOLLOWING WILL
4.5 CORRECTIVE MAINTENANCE OCCUR:
BEFORE CARRYING OUT ANY A. IMMEDIATE AND SEVERE DAMAGE TO PUMP
SERVICING OPERATION ON MECHANISM.
THE PUMP OR PIPING, DISCONNECT ELECTRICAL POWER
B. NO PUMPING OF FLUIDS.
FROM THE PUMP AND TAKE THE NECESSARY STEPS TO
ENSURE THAT ANY HARMFUL LIQUID CANNOT COME INTO C. REVERSE PUMPING ACTION (FROM DISCHARGE LINE
INTO SUCTION LINE).
CONTACT WITH PERSONNEL. SUITABLE PROTECTIVE
EQUIPMENT MUST BE PROVIDED. BE SURE THAT THERE IS
Preliminary Operations
NO FLUID PRESSURE IN THE PUMP LIQUID END AND PIPING.
1. Set the pump capacity knob to 0%. If stroke
Cleaning Fouled Check Valves: locking screw was previously tightened, slightly
Check valve assemblies are designed to be loosen the locking screw.
self-cleaning and should seldom need servicing. 2. Disconnect power to pump motor. Check that
Fouled check valves can usually be cleaned by the equipment cannot be accidentally started.
pumping a solution of mild detergent and warm Place a notice at the location of the power switch
water (if compatible with liquid being pumped) for indicating that the pump is being serviced.
15 minutes, followed by flushing with water.
3. Disconnect the pump hydraulically by removing
pipe or tubing connections to suction and
discharge check valves.

4.5.1 Check Valve Replacement: Liquid 4.5.2 Check Valve Replacement: Liquid Ends
Ends D2 and D4 - PVC, PVDF, H2SO4 D2 and D4 - Polymer (See Figure 9 or 12)
and Polypropylene (See Figure 9 or 12)
NOTE THAT THE SEAT ORIEN-
NOTE THAT THE SEAT ORIEN- TATION IS DIFFERENT INSIDE
TATION IS DIFFERENT INSIDE THE SUCTION AND DISCHARGE CHECK VALVES, BUT THE
THE SUCTION AND DISCHARGE CHECK VALVES, BUT THE SEAT MUST ALWAYS BE BELOW THE BALL WHEN INSTALLED.
SEAT MUST ALWAYS BE BELOW THE BALL WHEN INSTALLED.
DO NOT APPLY PTFE TAPE TO
DO NOT APPLY PTFE TAPE TO THE THREADS OF CHECK
THE THREADS OF CHECK VALVE BODY THAT SCREWS INTO THE HEAD (280), AS THIS
VALVE BODY THAT SCREWS INTO THE HEAD (280), AS THIS MAY PREVENT ADEQUATE SQUEEZE FROM BEING APPLIED
MAY PREVENT ADEQUATE SQUEEZE FROM BEING APPLIED TO THE VALVE O-RING WHICH COULD RESULT IN LEAKAGE.
TO THE VALVE O-RING WHICH COULD RESULT IN LEAKAGE.
Suction
1. Unscrew the valve body (424) from the pump
head (280).
head (280).
2. Remove the cartridge valve assembly: cartridge
2. Remove the valve assembly: assembly includes
includes ball (422), seat (420), ball guide (426),
ball (422), seat (420), Cartridge (426), O-ring
O-ring (419 and 421(D4 PVC / PVDF / POLY
(419) and washer (427).
only)) and washer (427).
3. Clean the valve body (424) and threaded port
in the head (280).
in the head (280).
4. Place a new washer (427) into valve body
4. Place a new washer (427) into valve body
(424). Place new seat (420) and new ball (422)
(424).
inside new cartridge (426) and place into valve
5. Install new check valve assembly in orientation
body.
shown.
5. Add O-ring (419) and install new check valve
On discharge side, drop cartridge assembly into
assembly in orientation shown.
threaded port in head. The O-ring should be
On suction side, drop the cartridge assembly into
stretched around outside of cartridge on same
check valve body. The O-ring should be stretched
end as ball seat. Screw valve body into discharge
around outside of cartridge on opposite end of ball
side of diaphragm head until valve is hand tight.
seat. Screw the suction valve body with cartridge
Do not overtighten.
valve into suction side of head hand tight. Do not
On suction side, drop the cartridge assembly into
overtighten.
check valve body. The O-ring should be stretched
around outside of cartridge on opposite end of ball Discharge
seat. Screw the suction valve body with cartridge 1. Unscrew the valve body (424) from the pump
valve into suction side of head hand tight. Do not head (280).
overtighten. 2. Remove the valve assembly: assembly includes
O-ring (419), seat (420), ball (422), spring (428),
cartridge (426) and washer (427).
in the head (280).

4. Place a new washer (427) into valve body (424). 4.5.4 Check Valve Replacement: Liquid End
Place new spring (428), new ball (422) and new Size D4 - Slurry (See Figure 11)
seat (420) inside new cartridge (426) and place 1. Unscrew the valve body (424) from the pump
into valve body. head (280).
5. Add O-ring (419) and install new check valve 2. Remove the valve assembly: assembly includes
assembly in orientation shown. ball (422), check valve body (424) and retainer
On discharge side, drop cartridge assembly into sleeve (428).
threaded port in head. The O-ring should be 3. Clean the valve body (424) and threaded port
stretched around outside of cartridge on same in the head (280).
end as ball seat. Screw valve body into discharge 5. Install new check valve assembly in orientation
side of diaphragm head until valve is hand tight. shown.
Do not overtighten. On discharge side, drop cartridge assembly into
threaded port in head. Screw valve body into
4.5.3 Check Valve Replacement:
Liquid End Sizes D2 and D4 - discharge side of diaphragm head until valve is
Metallic (See Fig. 10 or 11) hand tight. Do not overtighten.
The metallic check valves used on liquid end sizes On suction side, drop the cartridge assembly into
D2 and D4 (except slurry) are precision assembled check valve body. Screw the suction valve body
at the factory. Do not attempt to disassemble these with cartridge valve into suction side of head hand
cartridges. If they become inoperative, flush them tight. Do not overtighten.
with solvent, wash them with warm detergent and THE CHECK VALVES WILL NOT
blow them out with compressed air to remove any OPERATE IF THEY ARE
INSTALLED UPSIDE DOWN. INSTALL CHECK VALVES WITH
foreign matter. If this treatment does not eliminate
THE FLOW ARROW POINTING IN THE DIRECTION OF
the trouble, the cartridge assembly should be PROCESS FLOW (UP). TURN CHECK VALVE ASSEMBLIES
replaced. INTO LIQUID END BY HAND AND TIGHTEN. DO NOT OVER-
TIGHTEN, DAMAGE TO THE CHECK VALVES MAY OCCUR.
Disassembly
Remove the check valves by unscrewing them 4.5.5 Replacement of Ball, Seat, & Seal:
from the pump head. Liquid End D7 and D8 - PVC, PVDF,
H2SO4 and Polypropylene (See Figure 13)
Reassembly
Disassembly
Apply a small amount of thread sealing compound
1. Unscrew the union nut (435). The union end
and PTFE pipe tape to check valve threads and
(445) is held in place by the union nut and
install check valves by screwing them into the
will separate easily from the other liquid end
pump head with the flow arrows pointing up.
parts.
Do not overtighten check valves.
head (280).
3. Screw the union nut part way (one or two turns)
onto the end of the ball guide that has the seat
in it. Be sure the union nut is on loosely. This
will allow a gap for the seat (420) to fall into as
it is removed from the ball guide.

4. Set the ball guide / union nut on a flat surface 2. Set the body on a flat surface so that the end
with the union nut down. Looking into the top with the ball faces upward. Position seat (420)
of the ball guide, you will see four large holes on the body, with the beveled edge of the seat
surrounding one small hole. Insert a thin, blunt facing outward. When the seat is pressed into
instrument such as a hex head screwdriver into the body, the ball should be sitting on the side
the small center hole until it rests on the top of with sharp corners as shown in Figure 13.
the ball (422). The bevel should not face the inside of the
5. Tap screwdriver gently with a hammer until the check valve. Use a flat surface such as a board
ball and seat are released from the ball guide. to press the seat into the body with firm, even
pressure. If the seat is improperly positioned, the
IF THE UNIT IS DISASSEMBLED ball will not create a tight seal and poor pumping
FOR INSPECTION ONLY, BE
performance will result.
SURE TO USE A BLUNT INSTRUMENT AND TAP GENTLY TO
AVOID DAMAGING THE BALL. IF THE BALL AND / OR SEAT 3. Fit new O-rings (419) into position on the body
ARE DAMAGED DURING DISASSEMBLY, THEY WILL HAVE TO (424) and seat (420).
BE REPLACED. IF AVAILABLE, TO AVOID DAMAGE, IT IS
ADVISABLE TO USE GENTLE AIR PRESSURE (APPLIED AT DO NOT APPLY PTFE TAPE TO
END OPPOSITE THE SEAT (420) FOR BALL AND SEAT THREADS OF CHECK VALVE
REMOVAL) BODY (424) AS THIS MAY PREVENT ADEQUATE SQUEEZE
FROM BEING APPLIED TO THE VALVE O-RING WHICH WOULD
6. Carefully remove the two O-rings (419) from the
RESULT IN LEAKAGE.
ball guide and seat.
7. Carefully clean any parts to be reused. If any NOTE:
To assure a tight, leak free seal, new O-rings
chemicals are used in the cleaning process, should be used each time the check valves are
ensure that they are compatible with the process disassembled.
liquid.
4. Position the union end (445) onto the correct
Reassembly end of the body. Refer to Figure 13, as the
THE ORDER OF ASSEMBLY correct end is determined by whether the valve
AND ORIENTATION OF THE
is intended for the suction or discharge port of
SUCTION AND DISCHARGE CHECK VALVES IS DIFFERENT.
REFER TO FIGURE 13 FOR PROPER ASSEMBLY ORDER AND
the liquid end. Slip the union nut (435) over the
ORIENTATION. IF CHECK VALVE CARTRIDGES ARE INSTALLED union end and screw tightly (hand tight only)
INCORRECTLY, ONE OF THE FOLLOWING WILL OCCUR: onto the body.
(A) IMMEDIATE SEVERE DAMAGE TO PUMP MECHANISM. 5. Screw the valve assembly into the pump head
(B) NO PUMPING. (hand tight only). Do not overtighten.
(C) REVERSE PUMPING ACTION (FROM DISCHARGE LINE
INTO SUCTION LINE).
1. Drop the ball (422) into the curved inner

chamber end of the body (424).

4.5.6 Check Valve Replacement: Liquid End 4.5.7 Check Valve Replacement: Liquid End
Sizes D7 and D8 - Polymer (See Figure 13) Sizes D7 and D8 - Slurry (See Figure 13)
Suction 1. Unscrew the valve body (424) from the pump
Follow the instruction for replacement of ball, head (280).
seat and seal: liquid end D7 and D8 - PVC, 2. Remove the valve assembly: assembly includes
PVDF, H2SO4 and polypropylene paragraph 4.5.5. two O-rings (419), slurry seal ring (420), ball
The procedures are the same. (422), check valve body (424) and dowel pin.
Discharge
in the head (280).
head (280). 4. Install new check valve assembly in orientation
shown.
2. Remove the valve assembly: assembly includes
two O-rings (419), seat (420), ball (422), poppet On discharge side, drop cartridge assembly into
(426), spring (423) and check valve body threaded port in head. Screw valve body into
(424). discharge side of diaphragm head until valve is
hand tight. Do not overtighten.
3. Replace O-rings (419), seat (420), ball (422),
poppet (426) and spring (423). On suction side, drop the cartridge assembly into
check valve body. Screw the suction valve body
with cartridge valve into suction side of head hand
in the head (280).
tight. Do not overtighten.
5. Install new check valve assembly in orientation
shown. 4.5.8 Check Valve Replacement: liquid End
Sizes D7 and D8 - Stainless Steel
On discharge side, drop cartridge assembly into
(See Figure 14)
threaded port in head. Screw valve body into
discharge side of diaphragm head until valve is Disassembly
hand tight. Do not overtighten. Stainless steel check valves differ from the plastic
versions in that the ball seat is integral to the ball
guide. The seats cannot easily be inspected for
damage or wear. If you suspect that the check valve
may be damaged or worn, replace the entire check
valve assembly as per the instructions below.
1. Unscrew the coupling (445).
2. Unscrew the check valve assembly (425) from
the liquid end.

Reassembly 4.6 DIAPHRAGM AND OIL SEAL
THE ORDER OF ASSEMBLY BELLOWS REPLACEMENT
AND ORIENTATION OF THE BEFORE BEGINNING DIAPHRAGM
SUCTION AND DISCHARGE CHECK VALVES IS DIFFERENT. REPLACEMENT, MAKE SURE THAT
REFER TO FIGURE 14 FOR PROPER ASSEMBLY ORDER AND ALL SHUTOFF VALVES ARE CLOSED AND ALL PRESSURE IS
ORIENTATION. IF CHECK VALVE CARTRIDGES ARE INSTALLED BLED FROM THE LIQUID END.
INCORRECTLY, ONE OF THE FOLLOWING WILL OCCUR:
If failure of the oil seal bellows has occurred, it is
(A) IMMEDIATE SEVERE DAMAGE TO PUMP MECHANISM.
recommended that the diaphragm assembly and
(B) NO PUMPING.
oil seal bellows be replaced at the same time.
(C) REVERSE PUMPING ACTION (FROM DISCHARGE LINE
INTO SUCTION LINE). 4.6.1 Diaphragm Replacement: Liquid End
Size D2 (See Figures 7, 9 and 10)
1. Screw the correct end of the check valve
assembly into the pump head, trapping a new 1. Loosen the head screws (290) and remove the
O-ring between the pump head and the check diaphragm head (280). Mark the suction and
valve assembly. discharge ports on the diaphragm head prior
to removal.
DO NOT APPLY PTFE TAPE TO
2. Remove the motor fan cover and turn the motor
THREADS OF CHECK VALVE
BODY AS THIS MAY PREVENT ADEQUATE SQUEEZE FROM
by hand while adjusting the capacity control
BEING APPLIED TO THE VALVE O-RING WHICH WOULD knob to 100%. With the capacity set at 100%,
RESULT IN LEAKAGE. turn the motor fan until the diaphragm (260) is
in the full forward position (top dead center).
NOTE:
To assure a tight, leak free seal, new O-rings 3. Hold the outer edge of the diaphragm and turn
should be used each time the check valves are it counterclockwise to unscrew it from the pump
disassembled.
drive.
2. Screw the coupling (445) onto the check valve 4. Discard and replace with new diaphragm.
assembly, trapping a new O-ring (419) between Make sure that adaptor (252) is screwed in
the coupling and the check valve assembly. tightly to connecting rod (Item 60 in Figure
6). Make sure that seat ring (Item 230 in
Figures 9 and 10) is in place. Apply a thin
layer of silicone grease to back (rubber side)
of diaphragm before installation. Holding the
edges of the diaphragm, screw the diaphragm
assembly onto the male thread of the adaptor
piece (252) until it reaches its mechanical
stop.
5. With the capacity still set at 100% turn the motor
fan until the new diaphragm is in the farthest
rearward position (bottom dead center).
6. Reattach the diaphragm head with the suction
and discharge ports in the correct positions.
Tighten the screws in a crosswise pattern to a
torque of 45 in-lb.

7. While turning the motor fan, set the stroke 7. For Size D4-stainless steel liquid ends, slide bolt
adjustment knob to the 0% position. (250), washer (251) and O-ring (253) through
8. Reinstall motor fan cover. the diaphragm cap and diaphragm as shown
in Figure 7. For all other liquid ends, install set
4.6.2 Diaphragm Replacement: Liquid screw (Item 250 in Figure 6) into diaphragm cap
End Sizes D4, D7 and D8 (240), with hex hole in screw facing outward,
(See Figures 7, 11-14)
until it is bottomed out (hand tight only) in the
1. Mark the suction and discharge ports on the diaphragm cap.
diaphragm head prior to removal. Loosen the
8. Slide support nut (270) onto set screw in correct
head screws (290) and remove the diaphragm
orientation shown in Figure 7.
head (280).
9. Install hex nut onto back of support nut
2. Remove the motor fan cover and turn the
and tighten to the following torque values
motor by hand while adjusting the capacity
dependent on liquid end size and material.
control knob to 100%. With the capacity set at
Torque diaphragm assembly as follows:
100%, turn the motor fan until the diaphragm
cap (240) is in the full forward position a) Liquid End Size D7 and D8 to 20 foot pounds.
(top dead center). b) Liquid End Size D4-Plastic to 45 inch pounds.
3. Hold the outer edge of the diaphragm (260) and
c) Liquid End Size D4-Stainless Steel tighten
turn it counterclockwise to unscrew it from the
until washer (251) is contacting diaphragm
pump drive.
cap (240).
4. While clamping on the hex on the diaphragm
10. Make sure that support ring (230) is in place
cap (240), disassemble diaphragm assembly
and then reinstall diaphragm assembly.
by removing the hex nut (271) on the back of
the diaphragm support nut (270). 11. Apply thin layer of O-ring type grease to back
of support nut (270) and reinstall thin PTFE
5. Make sure that stainless steel support nut (270)
washer (274) to back of support nut.
is clean and free of corrosion. When cleaning
the support nut, take care not to scratch the 12. Make sure that oil seal clamp ring (210) is
smooth angled surface of the support nut. in place. Screw diaphragm assembly into
If corrosion cannot be removed without connecting rod (Item 60 in Figure 6) until it
damaging the support nut, replace with a new reaches its mechanical stop.
one. NOTE:
6. Install new diaphragm (260) onto diaphragm Steps 11 and 12 are applicable to Liquid End
Size D4.
cap (240) with the convolution in correct
orientation. As shown in figures, the convolution
in the Teflon diaphragm should be facing down
away from diaphragm cap (240) and against
(or pointing towards) the stainless steel support
nut (270).

13. Apply a thin layer of grease to the back of hex 4.7 OIL SEAL BELLOWS
nut (271). REPLACEMENT (ITEM 70 IN
FIGURES 9 THROUGH 14)
14. M a k e s u r e t h a t s p r i n g ( I t e m 2 7 2 i n
BEFORE BEGINNING OIL SEAL
Figure 13 and 14) is in place and connecting REPLACEMENT, MAKE SURE
rod is in full-forward position (at 100% capacity ALL SHUT-OFF VALVES ARE CLOSED AND ALL PRESSURE
setting). Screw diaphragm assembly into HAS BEEN BLED FROM THE LIQUID END (PUMP HEAD). WHEN
REPLACING THE OIL SEAL, THE DIAPHRAGM ASSEMBLY
connecting rod cross piece (61) until it reaches
MUST BE REMOVED FIRST. FOR EASE OF SERVICE, IT IS
its mechanical stop. RECOMMENDED THAT THE OIL SEAL BE REPLACED IN
CONJUNCTION WITH THE DIAPHRAGM ASSEMBLY.
NOTE:
Steps 13 and 14 are applicable to Liquid End 1. Disconnect connections to the pump motor
Size D7 and D8. terminal box. Be sure to note the wiring layout
15. With the capacity still set at 100% turn the before disconnecting from box.
motor fan until the diaphragm is pulled back to 2. Set the stroke adjusting knob to 100%.
the rearward position (bottom dead center). 3. Disconnect the suction and discharge
16. Reattach the diaphragm head with the suction connections to the pump head check valves.
and discharge ports in the correct positions. 4. Mark the suction and discharge ports on the
Torque the head assembly screws in a diaphragm head prior to removal. Loosen the
crosswise pattern as follows: head screws (290) and remove the diaphragm
a) Liquid End Size D2 and D4 to 45 inch head (280).
pounds. 5. Remove the motor fan cover and turn the
motor by hand while adjusting the capacity
b) Liquid End Size D7 and D8 to 90 inch
control knob to 100%. With the capacity set at
pounds.
100%, turn the motor fan until the diaphragm
17. While turning the motor fan, set the stroke
assembly is in the full forward position
adjustment knob to the 0% position.
(top dead center).
18. Reinstall motor fan cover.
6. Hold the outer edge of the diaphragm assembly
(260) and turn it counterclockwise to unscrew it
from the pump drive.
7. Remove the diaphragm support ring (230) from
the spacer (225).
8. Drain the oil out of the pump drive by removing
the drain plug from the pump housing.

9. Remove oil seal bellows clamping components 16. Reinstall liquid end components in accordance
as follows: with the procedures found in the following:
a) On Liquid End Size D2 models a) For Liquid End Size D2 models, refer to
(Figures 9 and 10), remove adaptor piece paragraph 4.6.1, steps 4 thru 7.
(252), clamp ring (210), mounting screws
b) For Liquid End Size D4, D7 and D8 models
(227) and spacer (225).
refer to paragraph 4.6.2, steps 10 thru 17.
b) On Liquid End Size D4 models 17. Connect the motor in compliance with the
(Figures 11 and 12), remove oil seal clamp directions marked during the prior disconnection
ring (210), mounting screws (227) and spacer (see also Section 2: ELECTRICAL
(225). CONNECTIONS).
c) On Liquid End Size D7 and D8 models
4.8 RESTARTING THE PUMP
(Figure 13 and 14), remove spring (272),
unscrew adapter (61), seal ring (210) 1. Reconnect the pump to the piping system.
mounting screws (227 & 228) and spacer 2. Check that capacity is set to 0%.
(225). 3. Open system suction and discharge shut-off
10. Pull the oil seal (70) off the connecting rod. valves and restart pump.
11. Install a new oil seal onto connecting rod. 4. Set the pump to 100% to obtain faster priming
12. Apply a thin layer of O-ring type grease to top of liquid end.
of oil seal (part adjacent to connecting rod). 5. A f t e r p r i m i n g , s e t t h e p u m p t o t h e
13. Reinstall parts removed in step 9. For Liquid desired capacity. Retighten locking screw
ends D2, D7 and D8, install adaptor piece (320, Figure 6).
(252) or cross piece (61) before mounting
spacer.
14. Remove the motor and refill pump drive with
oil (1 quart of Mobil SHC 629).
15. Reinstall motor.

SECTION 5 - PARTS LIST
GENERAL 4. Part Number Column
1. This section gives information regarding a. The supplier’s part number is listed in the
replaceable components. part number column.
5. Quantity Column
ILLUSTRATED PARTS LIST
1. Figure and Item Number Column a. The numbers appearing in the quantity
column are the total quantity of the listed part
a. The item numbers shown in the detailed
required in its immediate assembly.
parts list correspond to the item numbers
6. Reference Code Column
appearing on the exploded view illustration.
To find an unknown part number, locate the a. This column is used to denote assembly
part on the illustration and note the item and detail part variations among similar
number. Look for the item number on the components (models) covered by this
detailed parts list. The part number is on the publication. When the symbol “A” and “B”,
same line. A dash (-) precedes non-illustrated etc. is entered in this column, the part is
item numbers. used only in the model at which the symbol
2. Description Column appears. If the column is blank, the part is
used in all models.
a. The name of the item is in the description
Refer to table numbers (5.1 to 5.8) for the above
column.
Parts List information.
3. Additional Information
a. When “Consists of” is indented under a part,
that part consists of the corresponding parts
referenced by part number.

130
170
340
150
11 10
510 206
205
140 330
332
160
19
20 140
335
150
Figure 8. Drive Assembly (10227280007)

5.1 PARTS LIST FOR DRIVE
FIGURE ITEM PART QUANTITY

DESCRIPTION
NUMBER NUMBER NUMBER PUMP
Drive Housing Assembly, D2, 43 SPM, (NE56C) SD-40-01-NE56C 1
Drive Housing Assembly, D2, 43 SPM, (IEC71) SD-40-01-IEC71 1
Drive Housing Assembly, D4/7, 43 SPM, (NE56C) SD-40-06-NE56C 1
Drive Housing Assembly, D4/7, 43 SPM, (IEC71) SD-40-06-IEC71 1

10

8
Drive Housing Assembly, D8, 86 SPM, (IEC71) SD-20-10-IEC-71 1
11 Gasket Motor (NEMA 56C Flanged Motor) 2250115099 1
11 Gasket Motor (IEC71, V1 Flanged Motor) 2250121099 1
19 O-Ring 4080068031 1
20 Oil Drain Plug 60086 1
130 Retaining Ring 60064 1
140 Bearing 4099994000 2
- Items not shown.

FIGURE ITEM PART QUANTITY
DESCRIPTION
NUMBER NUMBER NUMBER PUMP
150 Retaining Ring 4040107231 2
160 Seal (Gasket), Side Cover, Use Through 2005 2502110067N 1
170 Seal, Oil, Use After 2005 H60766 1
205 Stroke Adjust Screw 61331 1
206 Socket Head Screw, M6 X 16, 304SS 4350003375N 3
330 Washer M6 304SS 4340009065N 3
332 Stroke Adjust Knob 70066 1
335 Pan Head Screw, M6 X 20 70054 2
340 Knob, Sticker MacRoy® 60996 1
- Bearing 61116 1
- Spring Pin (for IEC Motors Only) 4010003031 3

8
- Motor Mounting Bolt (IEC Motors: M8 X 25) 4350038522 4
- Motor Mounting Bolt (NEMA 56C Motors: 3/8-16 X 1) 4050018119 4
Motor Mount Washer (IEC Motors: Spring

- 4340009002 4
Lockwasher 8mm)
- Motor Mount Washer (NEMA 56C Motors: 3/8 SAE) 40476 4
- Base (Optional) 61266 1
- HEX HD, Screw, 3/8-16X1 GR5 4050018119 4
- Washer, 3/8 40476 4
- HEX Nut, 3/8-16NC Z PL 4050066016 4
- Gear Oil - 1 quart 4070324030 1
510 Breather Plug / Oil Fill Cap, P/O Item 10 41065 1
- Items not shown.

427
ASSEMBLY
424
425
427 252
427
420
422
430
419
290
PLASTIC
LIQUID END 300
ONLY
260
280
426
422 70
210
420
225
425
427
ASSEMBLY
419
424 422
427 420
428
426 422 426

427
420
419
424
POLYMER DISCHARGE CHECK POLYMER SUCTION CHECK
Figure 9. D2 Plastic Liquid End (10227800012)

5.2 PARTS LIST FOR D2 PLASTIC LIQUID END PVC, PVDF, BLACK POLY, H2SO4 AND POLYMER-
NPT / PVC, PVDF AND BLACK POLY-TUBING.
Model: Reference Code: Model: Reference Code:
D2_ _ 8P _ _ _ _ A (PVC NPT) D2_ _ 4P _ _ _ _ E (BLACK PP NPT)
D2_ _ 8T _ _ _ _ B (PVC TUBE) D2_ _ 4T _ _ _ _ F (BLACK PP TUBE)
D2_ _ 2P _ _ _ _ C (PVDF NPT) D2_ _ NP _ _ _ _ G (H2SO4 NPT)
D2_ _ 2T _ _ _ _ D (PVDF TUBE) D2_ _ PP _ _ _ _ H (POLYMER NPT)
FIGURE ITEM PART QUANTITY REFERENCE

DESCRIPTION
NUMBER NUMBER NUMBER PUMP CODE
70 Diaphragm / Oil Seal Bellows 60048 1

210 Oil Seal Clamp Ring 60043 1
225 Spacer 61035 1
230 Diaphragm Seat Ring 61088 1
252 Adapter 61083 1
260 Diaphragm, PTFE 30916 1
280 Diaphragm Head, PVC 61089 1 A, B, G
280 Diaphragm Head, PVDF 61090 1 C, D

280 Diaphragm Head, BLACK PP 61377 1 E, F
280 Diaphragm Head, POLYMER 69001 1 H
281 Decal 60534 1
9 290 Pan Head Screw, #10-24 X 3/4 61059 4
300 Flat Washer, 1/4 18.8SS 4040005012 4 A, E, G
300 Flat Washer, #10 18.8SS 4040002053 4 B, C, D, F
419 O-Ring, 0.549 ID X 103W(AFLAS) 36103 2
419 O-Ring, 2-113 Viton 40905 2 H
420 Ball Seat, 9/32 Ball, C-22 61107 2 A, B, C, D, E,F
420 Ball Seat, CA20 61439 2 G
420 Ball Seat, 3/8 Ball, 316SS 61270 2 H
422 Ball 9/32 Ceramic 35751 2 A, B, C, D, E,F
422 Ball 9/32, CA20 41655 2 G
422 Ball 3/8, 316SS 4070014112 2 H
424 Valve Body 1/4” NPT 36106 2 A, C, E, G, H
424 Fitting, 1/4 PVDF 36081 2 B, D, F
- Items not shown

PARTS LIST FOR D2 PLASTIC LIQUID END PVC, PVDF, BLACK POLY, H2SO4 AND POLYMER-
NPT / PVC, PVDF AND BLACK POLY-TUBING. (CONT.)

DESCRIPTION
Check Valve Assembly,

425 61141 2 A, C, E
PVC / PVDF / BLACK PP - NPT
425 61142 2 B, D, F
PVC / PVDF / BLACK PP - TUBE
426 Ball Cartridge 36113 2 A, B, C, E, F,G
426 Ball Cartridge 36116 2 H
9 427 Molded Washer, Cartridge Valve 36107 2
428 Spring, HAST-C 61275 2 H
435 Coupling Nut, PP 3/8 10299 2 B, D, F
445 Ferrule, 1/4” OD 28663 2 B, D, F
Liquid End Kit,
- RPM 099 1 A, B, C, D, E,F
PVC / PVDF / BLACK PP
- Liquid End Kit, POLYMER RPM 196 1 H
- Items not shown.

227
252
ASSEMBLY
425
230
290
260
280
70
425
210
225
ASSEMBLY
Figure 10. D2 Metallic Liquid End (102272800012)

5.3 PARTS LIST FOR D2 METALLIC LIQUID END STAINLESS STEEL-NPT
Model: D2 _ _ 7P
FIGURE ITEM QUANTITY REFERENCE

DESCRIPTION PART NUMBER
NUMBER NUMBER PUMP CODE

225 Spacer 61035 1
230 Diaphragm Seat Ring 61088 1
10 252 Adapter 61083 1
280 Diaphragm Head 61106 1
290 Pan Head Screw, #10-24 X 3/4 61059 4
425 Check Valve Assembly - NPT 21082 2
- Liquid End Kit, 316SS RPM 101 1
- Items not shown.

230
227
225
ASSEMBLY
70
425
280
290
240
251
250
253
271
425 270
ASSEMBLY 274 210
260
Figure 11. D4 Metallic Liquid End (10227280002)

5.4 PARTS LIST FOR D4 METALLIC LIQUID END STAINLESS STEEL-NPT
Model: D4 _ _ 7P _ _ _ _ A (316SS)

DESCRIPTION

225 Spacer 61035 1
230 Supporting Ring 61075 1
240 Diaphragm Cap, 316SS 61074 1
250 Hex Head Screw, M8 X 50, 316SS 61071 1
251 Washer, 8M, 316SS 61072 1
11 253 O-Ring, Viton 61073 1
270 Support Nut, 316SS 61051 1
271 Hex Nut, M8 Thin 61054 1
274 PTFE Washer 61055 1
280 Diaphragm Head, 316SS 61070 1
290 Pan Head Screw, #10-24 X 3/4 61059 4
425 Check Valve Assembly CV202294 2
- Liquid End Kit, 316SS RPM 104 1
- Items not shown.

428
424
427 422
428
426 422
424
420
419
POLYMER DISCHARGE CHECK 230 SLURRY CHECKS

227
424
ASSEMBLY
427 225
425
427 271
420
422 70
419
290
PLASTIC
LIQUID END 300 240
ONLY 280
PLASTIC
LIQUID END 250
DIAPH. ASSY
419
426
270
422
260 210
420
421 274
425
427
419 ASSEMBLY
422
420
426 427
424
POLYMER SUCTION CHECK
Figure 12. D4 Plastic Liquid End (10227280002)

5.5 PARTS LIST FOR D4 PLASTIC LIQUID END PVC, PVDF, BLACK POLY, H2SO4, SLURRY AND
POLYMER- NPT / PVC, PVDF, BLACK POLY AND H2SO4-TUBING.

D4_ _ 8P _ _ _ _ A (PVC NPT) D4_ _ 4T _ _ _ _ F (BLACK PP TUBE)
D4_ _ 8P _ _ _ _ B (PVC TUBE) D4_ _ NP _ _ _ _ G (H2SO4 NPT)
D4_ _ 2P _ _ _ _ C (PVDF NPT) D4_ _ NT _ _ _ _ H (H2SO4 TUBE)
D4_ _ 2T _ _ _ _ D (PVDF TUBE) D4_ _ PP _ _ _ _ I (POLYMER)
D4_ _ 4P _ _ _ _ E (BLACK PP NPT) D4 _ _ LP _ _ _ _ J (SLURRY)

DESCRIPTION
225 Spacer 61035 1
230 Diaphragm Support Ring 61075 1
A, B, E, F, G,
240 Diaphragm Cap - PVC 61052 1
H, I
240 Diaphragm Cap - 316SS 61074 J
240 Diaphragm Cap - PVDF 61053 1 C, D
250 Socket Set Screw, M8 X 50 61058 1
Socket Set Screw, M8 X 50,
250 61071 1 J
316SS
12
253 O-Ring, 8MM ID, T=2MM, Viton 61073 1 J
270 Support Nut, 316SS 61051 1
271 Hex Nut, M8 X 50 61054 1
274 Washer, PTFE 61055 1
280 Diaphragm Head - PVC 61056 1 A, B, G, H, I
280 Diaphragm Head - PVDF 61057 1 C, D
280 Diaphragm Head - Black PP 61236 1 E, F
Diaphragm Head - 316SS
280 61070 1 J
(SLURRY)
- Decal 60534 1
- Decal, EAC Logo 2530118099 1
- Items not shown.

PARTS LIST FOR D4 PLASTIC LIQUID END PVC, PVDF, BLACK POLY, H2SO4, SLURRY AND
POLYMER- NPT / PVC, PVDF, BLACK POLY AND H2SO4-TUBING. (CONT.)

DESCRIPTION
290 Pan Head Screw, #10-24 X 3/4 61059 4
300 Flat Washer, #10 18.8SS 404000205 4
419 O-Ring, AFLAS 36103 2 E, F, G, H
419 O-Ring, Viton 40905 2 I,J
420 Ball Seat, 0.375, PTFE 39425 2 A, B, C, D, E, F
420 Ball Seat, 3/8” Ball, CA-20 61316 2 G,H
420 Ball Seat, 3/8” Ball, 316SS 61270 2 I
421 O-Ring, AFLAS 39413 2 A, B, C, D, E, F
422 Ball, 3/8” CERAMIC,+/-.001 10338 2 A, B, C, D, E, F
422 Ball, 3/8” 316SS, Grade 50 4070014112 2 I
422 Ball, 3/8” CA-20, Grade 50 4070014113 2 G,H
Ball, 7/16” 316SS,
422 CV102313 2 J
P/O 22312, Item 425
12 424 Fitting, 1/4 PVDF - NPT 36106 2 E, G, I
424 Fitting, 1/4 PVDF - TUBE 36081 2 F
424 Fitting, 1/2 PVDF - TUBE 36138 2 H
Check Valve Body,
424 22313 2 J
P/O 22312, Item 425
425* Check Valve Assembly - NPT, 1/4” 36366 2 A, C
Check Valve Assembly -
425* 36360 2 B, D
TUBE, 1/2”
425 Check Valve Assembly - PP 36306 2 E, F
425 Check Valve Assembly - H2SO4 39461 2 G, H
425 Check Valve Assembly - SLURRY 22312 2 J
426 Cartridge, 0.375 PVDF 36116 2 E, F, G, H, I
427 Washer 36107 2 E, F, G, H, I
- Coupling Nut, 1/2” 10411 2 H
- Items not shown

PARTS LIST FOR D4 PLASTIC LIQUID END PVC, PVDF, BLACK POLY, H2SO4, SLURRY AND
POLYMER- NPT / PVC, PVDF, BLACK POLY AND , H2SO4-TUBING. (CONT.)

DESCRIPTION
Spring, Lee LC-016C-8-HAST-C,
428 61275 1 I
(Suction Only)
428 Retainer Sleeve 61071 1 J
- Coupling Nut 10299 2 F
- Ferrule, 1/4” OD 28663 2 F
12 Liquid End Kit, PVC, PVDF,
- RPM 102 1 A,B,C,D,E,F
BLACK PP NPT / TUBE
- Liquid End Kit, H2SO4 NPT RPM 173 1 G
- Liquid End Kit, H2SO4 TUBE RPM 174 1 H
- Liquid End Kit, POLYMER RPM 196 1 I
- Liquid End Kit, SLURRY RPM 212 1 J
- Items not shown

445
228 227
419 435
425
273
Check Valve
424
Assembly 422
423 62
420
KIT
419
260
271 274
70
280
Direction 240
of Flow 250
270
290 300
302 305
419 61
225
425 424 272
Check Valve 422
Assembly 423 420 448

230
KIT 419
445
435
419
445 445
419 420
420 435
419
424 424
419 423 422
424 426 419
425 422 420

419
435
419
420 445 445
419
SLURRY DISCHARGE POLYMER SLURRY SUCTION POLYMER SUCTION

CHECK DISCHARGE CHECK CHECK CHECK
Figure 13. D7 & D8 Plastic Liquid End (1022819000)

5.6 PARTS LIST FOR D7 AND D8 PLASTIC LIQUID END PVC-NPT / TUBING, PVDF-NPT, BLACK
POLYNPT, POLYMER-NPT, SLURRY-NPT & H2SO4-NPT.

D7/D8_ _ 8P _ _ _ _ A (PVC NPT) D7/D8_ _ PP _ _ _ _ E (POLYMER NPT)
D7/D8_ _ 2P _ _ _ _ B (PVDF NPT) D7/D8_ _ 4P _ _ _ _ F (BLACK PP NPT)
D7/D8_ _ LP _ _ _ _ C (SLURRY NPT) D7/D8_ _ 8T _ _ _ _ G (PVC TUBE)
D7/D8_ _ NP _ _ _ _ D (H2SO4 NPT)
FIG. ITEM D7 D8 QTY. REFERENCE

DESCRIPTION
NO. NO. PART NO. PART NO. PUMP CODE
61 Adapter 61155 61155 1

62 Socket Head Set Screw, M8 X 20 4350016075N 4350016075N 1
70 Oil Seal Bellows 60048 60048 1
- PTFE Seal Ring 61154 61154 1
225 Spacer 61156 61156 2
Socket Head Set Screw,

227 4350003375N 4350003375N 2
M6 X 16, 304SS
Socket Head Set Screw,

228 4350047395N 4350047395N 1
M6 X 30, 304SS
230 Diaphragm Support Ring 60035 60035 1

240 Diaphragm Cap - PVC 60628 60628 1 A, C, D, E,F, G
240 Diaphragm Cap - PVDF 60630 60630 1 B
13
Socket Set Screw,
250 4350071284 4350071284 1
Dog PT M10 X 45
260 Diaphragm, PTFE 60618 60618 1
270 Support Nut 61065 61065 1
271 Hex Nut, M10 Thin, 316SS 61068 61068 1
272 Spring 70081 70081 1
273 Spring Cup 61153 61153 1
280 Head PVC 60033 60033 1 A, C, D, E,G
280 Head PVDF 60031 60031 1 B
280 Head Black Polypropylene 60882 60882 1 F
281 Decal, Tighten MacRoy® Plastic 60534 60534 1
282 Decal, EAC Logo 2530118099 2530118099 6
- Items not shown.

* Items included as part of item number 425.
PARTS LIST FOR D7 AND D8 PLASTIC LIQUID END PVC-NPT / TUBING, PVDF-NPT, BLACK
POLYNPT, POLYMER-NPT, SLURRY-NPT & H2SO4-NPT. (CONT.)

DESCRIPTION
Hex Head Screw, M8 X 110mm,

290 4350001655 4350001655 6
LG 304SS
300 Flat Washer, M8, Regular 304SS 4340005085 4340005085 1 A, B, C, D,E, G
- Back-up Plate 60754 60754 6
302 Split Washer M8, 304SS 4340009005 4340009005 6
-304 Nut Spacer 61152 61152 6
305 Hex Nut, M8, 304SS 4350000045 4350000045 4
419* O-Ring, Viton, 2-117 4080068075 4080068075 4 A, C, D, E,F, G
419* O-Ring, PTFE, TEFLEX 2-117 40348 40348 2 B
420* Seat, PVDF 2240173078 2240173078 2 A, B, F, G
420* Slurry Seal Ring, 316SS 60819 60819 2 C
420 Seat, 5/8” Ball 316SS 240173016 240173016 2 E
420 Seat, 5/8” Ball CA20 60855 60855 2 D
13 422 Ball, 14MM 316SS 60709 60709 2 C
422* Ball, 5/8 Ceramic 4070015171 4070015171 2 A, B, G
422 Ball, 5/8 Ceramic 4070015171 4070015171 2 F
422 Ball, 5/8 CA20 4070014173 4070014173 2 D
422 Ball, 5/8 316SS 4070014172 4070014172 2 E
422 Ball, 5/8 316SS 4070014172 2 F

Spring, Hastelloy,
423 800123026 800123026 1 E
(Discharge Only)
Kit - Ball, Seat & O-Rings, PVC,
423 3050879500 3050879500 2 A
Includes items 419, 420, and 422
Kit - Ball, Seat & O-Rings,
423 3050879700 3050879700 2 B
Includes items 419, 420, and 422
Kit-Ball, Body, & Dowel Pin,
423 61238 61238 2 C
Includes Items 422, 424 and 426
424* Cartridge Body, PVDF 60024 60024 2 A, B, D, E,F, G
424 Slurry Valve Body 30156071 30156071 1 E
- Items not shown


PARTS LIST FOR D7 AND D8 PLASTIC LIQUID END PVC-NPT / TUBING, PVDF-NPT, BLACK
POLYNPT, POLYMER-NPT, SLURRY-NPT & H2SO4-NPT. (CONT.)

DESCRIPTION
424 Ball Guide, PVC, Spring Loaded 60818 60818 2 C

Check Valve Assembly, PVC,
425 3050870007 3050870007 2 A
Includes Items 423 and 424
425 PVDFIncludes Items 423 and 3050870008 3050870008 2 B
424
Check Valve Assembly, Slurry,
425 60827 60827 2 C
Includes Items 419, 420 and 423
- Dowel Pin, 3/16 X 1.5, 416SS 60820 60820 2 C
426 Poppet, PVDF 440090078 440090078 1 E
435 Union Nut, 1/2” PVC 4320236038 4320236038 2
445 Union End, 1/2” NPT PVC 60117 60117 2 A, C, D,E, F, G

13 445 Union End, 1/2” NPT PVDF 60119 60119 2 B
- Elbow 1” MPT X 1” BARB PVDF 61395 2 G

Elbow 1/2” MPT X 1/2” BARB
- 61396 2 G
PVDF
448 Blow-Off Nozzle 470096073N 470096073N 1
Liquid End Kit, PVC-NPT / TUBE
- RPM 135 RPM 105 1 A, F, G
and Black PP NPT
- Liquid End Kit, PVDF NPT RPM 136 RPM 106 1 B
- Liquid End Kit, Slurry NPT RPM 215 1 C
- Liquid End Kit, Polymer NPT RPM 211 RPM 210 1 E
- Liquid End Kit, H2SO4 NPT RPM 175 RPM 183 1 D
- Items not shown.


445 302 305
419
228 227
273
Assembly 62
425
419
260
271
70
280
240
250
270
290 300
302 304 305

419 61
225
Assembly
272
425
230 448
419
445
Figure 14. D7 & D8 316SS Liquid End (1022819000)

5.7 PARTS LIST FOR D7 AND D8 316SS-NPT LIQUID END
Model: D7 _ _ 7P _ _ _ _ _ or D8 _ _ 7

DESCRIPTION
61 Adapter 61155 61155 1
62 Socket Head Set Screw, M8 X 20 4350016075N 4350016075N 1
70 Oil Seal Bellows 60048 60048 1
210 PTFE Seal Ring 61154 61154 1
225 LE Adapter 61156 61156 1
Socket Head Set Screw, M6 X 16,

227 4350003375N 4350003375N 2
304SS
Socket Head Set Screw, M6 X 30,

228 4350047395N 4350047395N 2
304SS
230 Support Ring 60035 60070 1
240 Diaphragm Cap - 316SS 60631 60636 1
250 Socket Set Screw, Dog PT M10 X 45 4350071284 4350071284 1
260 Diaphragm, PTFE 60618 60624 1
270 Support Nut 61065 61146 1

14
271 Hex Nut, M10 Thin, 316SS 61068 61068 1
272 Spring 70081 70081 1
273 Spring Cup 61153 61153 1

280 Head, 316SS 210760016 61149 1
Hex Head Screw, M8 X 110mm,
290 4350001655 4350001655 6
LG 304SS
300 Flat Washer, M8, Regular 304SS 4340005085 4340005085 6
302 Split Washer M8, 304SS 4340009005 4340009005 6
304 Nut Spacer 61152 61152 6
305 Hex Nut, M8, 304SS 4350000045 4350000045 6
419 O-Ring, 2-117 Viton 4080068075 4080068075 4
425 Check Valve Assembly 3050876602 3050876602 2
445 Coupling, 1/2” NPT 60135 60135 2
448 Blow-Off Nozzle 470096073N 470096073N 1
- RPM Kit, 316SS RPM137 RPM107 1
- Items not shown

750
850
830
263
1240 1230 1220
820
290
262
250
760
840
264
810
860 870 880
770
780 266
790
800
Figure 15. Leak Detection, Switch and / or Gauge (Optional) (10227280005)

264 263 261
300
290
250
266 262
Figure 16. Double Diaphgram, D4 Pressure Type Configured (Optional) (102272800010)
263
290 300
302 304
305
262
264
266
Figure 17. Double Diaphgram, D7 & D8 Pressure Type Configured (Optional) (10227280005)

5.8 LEAK DETECTION PARTS LIST
Model: Code: Model: Code:
D2 _ _ _ _ _ _ _ A D7 _ _ _ _ _ _ _ C
D4 _ _ _ _ _ _ _ B D8 _ _ _ _ _ _ _ D
QUAN-
FIGURE ITEM REFERENCE
DESCRIPTION PART NUMBER TITY
NUMBER NUMBER CODE
PUMP
250 Stud, Modified, 1/4 X 1-3/8 61379 1 A
250 Set Screw, M8 61262 1 B
Set Screw, Socket, Dog Pt.
250 4350071334 1 C, D
M10X70MM
252 Adapter, Double Diaphram 61380 1 A
261 Support Ring D4 61075 1 B

Ring, Seat, Double
262 61386 1 A
Diaphram
Spacer, Double Diaphram,
262 61258 1 B
PVC
262 980367071 1 C
PVC
262 980369071 1 D
PVC
15,16 & Ring, Spacer,

263 61256 1 B
17 Double Diaphram
263 Ring, Intermed. - PVC 980366071 1 C

263 Ring, Intermed. - PVC 980368071 1 D
264 Diaphram, PTFE 61381 1 A
264 Diaphram, PTFE 60995 1 B
264 Diaphram, PTFE 60618 1 C
264 Diaphram, PTFE 60624 1 D
Connector, Male, 1/16
266 61378 1 A
NPTM X 1/8 Tube
266 Nipple, Hex, 1/8NPT 40596 1 B
Nipple, Hex,
266 60208 1 C, D
1/4 NPT X 1/4 BSP
Screw, Panhead,
290 61385 4 A
10-24 x 1-1/2
Screw, Socket Head,
290 41069 4 B
#10 - 24 X 1-3/4
- Items not shown

LEAK DETECTION PARTS LIST

Screw, Hex Head,

290 60206 6 C
M8 X 130 MM - 304SS
Screw, Hex Head,
290 61319 6 D
M8 X 140 MM - 304SS
Flat Washer, #10, 18.8SS,
300 4040002053 4 A, B
For PVDF Head
300 Flat Washer, M8, 304SS 4340005085 6 C, D
302 Lock Washer, M8, 304SS 4340009005 6 C, D
304 Spacer 61152 6 C, D
305 Nut, M8, 304SS 4350000045 6 C, D
750 Bracket 2040199006 1
Switch, NEMA 4 Pressure,
760 4060388001 1
5 - 30 PSI
Switch, NEMA 7 Pressure,
760 4060389001 1
5 - 30 PSI
Nipple, Reducing
770 40064 1
Hex 1/2 X 1/8 NPT
15,16 &
17 780 Tee, 1/8 NPT Female, 316SS 40062 2
790 Valve, Bleed, 1/8 NPT, 316SS 40063 1

Connector, Tube, 1/8 TUBEX,
800 40061 3
NPT
810 Tubing, Gauge to Switch 2490136016 1
Adapter, Reducing,
820 40067 1
1/4F X 1/8M NPT
Gage, Pressure, 0-400 PSI,
830 40066 1
(Dual Face)
Check Valve, 1/8 Tube
840 40065 1
(1/3 PSI) - 316SS
Tubing, Pump to
850 2490137116 1
Gauge - 316SS
Screw, Hex Head,
860 4050016095 2
1/4 - 20 X 3/4 18.8SS
Lock Washer, Spring,
870 4040039022 2
1/4 - 18.8SS
- Items not shown

LEAK DETECTION PARTS LIST

880 Nut, Hex, 1/4-20 - 18.8SS 4050064012 2 A

Screw, Pan Head,
1220 4050263050 3
#4-40 X 1/2
Lockwasher, Spring,
1230 4040095023 3
#4, 18.8SS
1240 Nut, Hex, #4 - 40, 18.8SS 4050182012 3

15,16 &
17 Liquid End Kit, PVC, PVDF,
- RPM 161 1 A
BLACK PP DD
- Liquid End Kit, 316SS, DD RPM 162 1 A
Liquid End Kit, PVC, PVDF,
- RPM163 1 B
BLACK PP DD
- Liquid End Kit, 316SS, DD RPM 164 1 B
- Items not shown

SECTION 6 - TROUBLESHOOTING
SYMPTOMS POSSIBLE CAUSE REMEDY

a) Low process liquid level in the
a) Add liquid.
tank.
b) Worn or dirty check valves. b) Clean or replace.
c) Blocked discharge line. c) Clear line.
d) Thaw liquid throughout pumping
d) Frozen liquid.
system.
e) Blown fuse e) Replace fuse.

1. Pump motor won't operate
f) Open thermal overload device in
f) Reset device.
motor starter.
g) Broken wire. g) Locate and repair.
h) Investigate and correct
h) Low voltage.
(wiring may be too tight)
i) Allow suction line and pump
i) Pump not primed head to fill with liquid before
pumping against pressure.
j) Capacity adjustment set at zero. j) Readjust capacity.
a) Incorrect capacity adjustment. a) Readjust capacity setting.
b) Match line voltage and frequency
b) Incorrect pump speed.
to pump motor data plate.
c) Increase piping size or suction
c) Starved suction.
head.
d) Leaky suction piping. d) Repair piping.
e) Rearrange equipment to
e) High suction lift. decrease lift and / or install foot
valve in suction line.
2. Insufficient pump delivery.
f) Cool liquid or increase suction
f) Liquid near boiling.
head.
g) Leaky safety valve in discharge
g) Repair or replace valve.
line.
h) Reduce viscosity (e.g., heat or
dilute liquid), or consult Milton
h) High liquid viscosity.
Roy for a special check valve
options.
i) Worn or dirty check valve seats. i) Clean or replace.
a) Leaky suction piping. a) Repair piping.
b) Leaky safety valve. b) Repair or replace valve.
c) Raise suction tank level and / or
c) Insufficient suction head.
install foot valve in suction line.
3. Erratic pump delivery
d) Cool liquid or increase suction
d) Liquid near boiling.
head.
e) Worn or dirty check valves. e) Clean or replace.
f) Clogged or dirty line strainer. f) Clean strainer.

SYMPTOMS POSSIBLE CAUSE REMEDY
a) Normal operating temperature of
both motor and pump body is
frequently uncomfortable to the a) N/A
touch. However, neither should
exceed 200°F (93°C).
b) Power supply does not match b) Insure proper matching of power
4. Motor and pump body hot electrical requirement of motor. supply and motor.
c) Reduce pressure or stroke
c) Pump is being operated at
speed. If this is not practical,
greater than rated performance.
contact service facility.
d) Drain oil and refill with proper
d) Pump improperly lubricated. amount of recommended
lubricant.
a) Misadjusted capacity knob. a) Readjust capacity setting.
5. Pump still pumps even at
zero capacity setting b) Correct condition (e.g., install
b) Insufficient discharge pressure.
a back pressure valve).
a) Excessive backlash. a) Consult service facility.
6. Gear noise b) Worn bearings. b) Consult service facility.
c) Wrong or insufficient lubricant. c) Replace or replenish lubricant.
7. Loud knock with each a) Excessive gear set wear. a) Consult service facility.
stroke b) Worn bearings. b) Consult service facility.
a) Ball checks move up and down
with some force. A distinct
8. Noisy operation in liquid
a) Noise in check valves. "clicking" noise is normal,
end
especially in metal piping
systems.

Ingersoll Rand (NYSE:IR) advances the quality of life by creating comfortable, sustainable and efficient environments. Our
people and our family of brands— including Club Car®, Ingersoll Rand®, Thermo King® and Trane®—work together to
enhance the quality and comfort of air in homes and buildings; transport and protect food and perishables; and increase
industrial productivity and efficiency. We are committed to a world of sustainable progress and enduring results.
[email protected]
www.miltonroy.com MacRoy is a registered trademark of Milton Roy, LLC.
®
© 2019 Milton Roy, LLC.

MacRoy D IOM

Uploaded by

Copyright:

Available Formats

MacRoy D IOM

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MacRoy D IOM

Uploaded by

Copyright:

Available Formats

MacRoy® D Metering Pump

Caution on Chemical Concentration:

Flow Indicating Device:

Head Loss / Over Pressure Protection / Back Pressure-Anti-Siphon Valve:

2 Instruction, Operations & Maintenance Manual

Pumps Water “Primed”

Plumbing and Electrical Connections

Over Pressure Protection

4 Instruction, Operations & Maintenance Manual

Instruction, Operations & Maintenance Manual 5

6 Instruction, Operations & Maintenance Manual

English Units Metric Units

Instruction, Operations & Maintenance Manual 7

Figure 1. Pump Assembly

1 Motor 5 Liquid End Mounting Assembly

8 Instruction, Operations & Maintenance Manual

Figure 2. Stroke Control Operating Principle

Instruction, Operations & Maintenance Manual 9

10 Instruction, Operations & Maintenance Manual

2.1 UNPACKING If equipment is to be shipped directly from Milton

Short Term Storage (Less than 6 Months) Electrical Equipment

Instruction, Operations & Maintenance Manual 11

12 Instruction, Operations & Maintenance Manual

3.33 4.47 MAX. B

Figure 3. MacRoy® D Dimensional Outline (1022784000)

Instruction, Operations & Maintenance Manual 13

Figure 4. Typical Installation

14 Instruction, Operations & Maintenance Manual

2.6 INSTALLATION To minimize viscous flow losses when handling

Figure 5. General Piping

Instruction, Operations & Maintenance Manual 15

16 Instruction, Operations & Maintenance Manual

2.7 VALVES 2.7.3 Safety Valves and Priming Valves

Instruction, Operations & Maintenance Manual 17

18 Instruction, Operations & Maintenance Manual

Check Valves Visual Check of Seal Integrity of Mechanical

Instruction, Operations & Maintenance Manual 19

Figure 6. Drive Assembly (10227280007)

ITEM ITEM ITEM

20 Instruction, Operations & Maintenance Manual

Figure 7. Diaphragm Assemblies By Liquid End Size and Material

22 Instruction, Operations & Maintenance Manual

2 each, Check Valve Assembly: Item 425 in

Instruction, Operations & Maintenance Manual 23

24 Instruction, Operations & Maintenance Manual

Instruction, Operations & Maintenance Manual 25

26 Instruction, Operations & Maintenance Manual

1. Drop the ball (422) into the curved inner

Instruction, Operations & Maintenance Manual 27

28 Instruction, Operations & Maintenance Manual

Instruction, Operations & Maintenance Manual 29

30 Instruction, Operations & Maintenance Manual

Instruction, Operations & Maintenance Manual 31

32 Instruction, Operations & Maintenance Manual

Instruction, Operations & Maintenance Manual 33

Figure 8. Drive Assembly (10227280007)

34 Instruction, Operations & Maintenance Manual

FIGURE ITEM PART QUANTITY

Drive Housing Assembly, D2, 43 SPM, (NE56C) SD-40-01-NE56C 1