Scribd Logo
Upload

Welcome to Scribd!

  • 368 views

    Manual Gerador RF Chinês

    Uploaded by

    Alex Fernandes
    This document provides instructions for using a 0.5MHz-470MHz radio frequency signal source to test the receiving sensitivity of radios. It can output signals from -70 to -132 dBm and modulate an 800Hz audio tone. The signal source is accurate for measuring sensitivity, which is typically -120 to -130 dBm for handheld radios. To test, the frequency is set to match the radio and lowered until audio is just clear, indicating the radio's sensitivity level. The device has numeric keys, function keys to control settings like frequency and modulation, and can generate analog or digital subtones. Care must be taken not to transmit while connected to a radio to avoid damage.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Manual Gerador RF Chinês

    Uploaded by

    Alex Fernandes
    368 views2 pages
    This document provides instructions for using a 0.5MHz-470MHz radio frequency signal source to test the receiving sensitivity of radios. It can output signals from -70 to -132 dBm and modulate an 800Hz audio tone. The signal source is accurate for measuring sensitivity, which is typically -120 to -130 dBm for handheld radios. To test, the frequency is set to match the radio and lowered until audio is just clear, indicating the radio's sensitivity level. The device has numeric keys, function keys to control settings like frequency and modulation, and can generate analog or digital subtones. Care must be taken not to transmit while connected to a radio to avoid damage.

    Original Title

    manual gerador RF chinês

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for using a 0.5MHz-470MHz radio frequency signal source to test the receiving sensitivity of radios. It can output signals from -70 to -132 dBm and modulate an 800Hz audio tone. The signal source is accurate for measuring sensitivity, which is typically -120 to -130 dBm for handheld radios. To test, the frequency is set to match the radio and lowered until audio is just clear, indicating the radio's sensitivity level. The device has numeric keys, function keys to control settings like frequency and modulation, and can generate analog or digital subtones. Care must be taken not to transmit while connected to a radio to avoid damage.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    368 views2 pages

    Manual Gerador RF Chinês

    Uploaded by

    Alex Fernandes
    This document provides instructions for using a 0.5MHz-470MHz radio frequency signal source to test the receiving sensitivity of radios. It can output signals from -70 to -132 dBm and modulate an 800Hz audio tone. The signal source is accurate for measuring sensitivity, which is typically -120 to -130 dBm for handheld radios. To test, the frequency is set to match the radio and lowered until audio is just clear, indicating the radio's sensitivity level. The device has numeric keys, function keys to control settings like frequency and modulation, and can generate analog or digital subtones. Care must be taken not to transmit while connected to a radio to avoid damage.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 2

    0.

    5MHZ-470MHZ radio frequency signal source with sub-tone

    output radio sensitivity test

    The accuracy comparison between this signal source and professional


    comprehensive measurement is basically the same. The accuracy is very high.Can
    test the actual receiving sensitivity of the radio. Unit is DBM
    Generally, the sensitivity of the hand table is -120DBM to -130DBM. The greater
    the negative sensitivity, the higher the sensitivity. The signal source cannot input
    power. It is absolutely forbidden to press the radio transmission key during the test.
    (Self-equipped power supply 8V-12V, the polarity of the power supply is positive and
    negative outside)

    Test Methods:
    During testing, the frequency of the signal source input radio is first set to -
    100DB or any value. The walkie-talkie has audio output, and then reduces the output
    intensity of the signal source.
    For example, the signal source is reduced to -120DB, and the audio signal of the
    radio is heard but noisy. The audio signal is just clear. The -120DB value of this output
    is the receiving sensitivity of the radio.
    Dedicated for FM radio debugging
    Frequency 0.5M --- 470M
    Signal strength -70--132dBm
    Built-in 800Hz audio modulation
    Newly added analog subtone digital subtone function.
    7-digit with 8--12V DC power frequency
    For example: 439.6000MHZ shows 4396000KHZ
    Signal strength-70--132 dBm is valid Other values are invalid
    Audio modulation is only about 800Hz and other values are invalid

    Signal source description


    Note that the radio cannot be placed in the transmitting state when the signal source
    is connected to the radio, otherwise the signal source will be damaged
    First line, left frequency (0.5-470M), right modulation sound (1-3K)
    The second line, the left sub-audio (50.0-280.0Hz any analog sub-tone and 105 digital
    sub-tones), the right output power (-70 --- 131dBm)

    Numeric keys: Enter directly for the cursor pointing to the item
    Up and down keys: step to adjust the cursor to the item value
    F1 key: cursor moves
    F2 key: Backspace key
    F3 key: Function key. The cursor points to the item cycle switch. For example: when
    the cursor points to the modulation tone, the function of this key is to cycle the
    modulation tone.
    F4 key: cycle switch RF signal output

    Analog sub-tone setting: directly input 4 digits of sub-audio points, less than 4 digits
    before "0". Example: 88.8Hz input
    Now if you use the up and down keys to adjust, it will be adjusted in 0.1Hz steps.
    0, 0, 0, 0 and then use the up and down keys to adjust from the first standard
    subtone 67Hz adjustment.
    Digital subtone setting: Enter the 3-digit subtone code, and then press F3. Example
    023: Enter 0, 2, 3, and then press F3. The setting is successful. Press the F2 key to
    switch between I and N of the digital subtone. Adjust the up and down The key will
    add or subtract 105 sets of digital tones.
    A modulation tone and subtone value of 0 is equivalent to turning off.

    You might also like