Contents

1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Idle Mode
Macro IBS
Reselection Priority

6 L1800 (10M) S<-70dBm

N>S+4dB

5 L2100 (5M) L2100 (5M)

Priority
Trigger
Coverage
Trigger
3 U2100 F2 U2100 F2

3 U2100 F1 U2100 F1

2 U900 U900

1 GSM900 GSM900

Intra-freq Inter-freq/Inter-Rat Inter-freq/Inter-Rat

Reselection Reselection (Bidirectional) Reselection (Unidirectional)
Idle Mode
Idle Mode reselection strategy:
• L<->L: Intra-Freq, Inter-Freq reselection
• L->U: coverage based reselection
• LTE is preferred higher reselection priority than GSM and UMTS
• With the same BW, U900 has lower priority than U2100 because it has wider coverage
• GU->L: reselection based on priority (LTE has highest reselection priority, GSM has the lowest reselection priority)

UE prefer to stay in LTE when LTE coverage exists

• Once UE detect LTE signal higher than reselection threshold, then reselect from GU to LTE
• L1800 has highest priority with largest bandwidth (10MHz)

UE will reselect to UMTS/GSM if moves out of LTE coverage area

• UE will start to detect (UMTS U2100 F1)/(GSM 900) signal when LTE serving RSRP drop to below none-intra-freq search
threshold, and trigger reselect to UMTS/GSM when LTE signal further drop to below reselection threshold and UMTS/GSM
signal higher than required threshold
• UE will reselect to UMTS in areas that exist Huawei 3G coverage, and reselect to GSM if there is not 4G and 3G at the same
time
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Idle Mode (Intra-Freq Reselection)
• Intra-Frequency reselection will be triggered when UE moves toward out of the serving cell coverage area
• UE will reselect to the best cell that the RSRP is better than the serving cell

TReselEUTRAN

RSRP
Ms
Mn

- 70dBm ●

Ms+Qhyst

QRxLevMin
-128dBm
Time
Trigger cell reselection
SIntraSearch

Reselection condition
Measurement trigger Reselection to neighbor
RSRP(S)<RSRP(N)-4dBm, cell
Idle, RSRP(S)<-70dBm
lasts 1s
Idle Mode (Intra-Freq Reselection)
Recommended
Category Parameter Name MO MML Command Parameter Remark
Value
Minimum required RSRP of cell for UE to
Minimum required RX level (Unit:2dBm) QRxLevMin -64 camp on 
CellSel MOD CELLSEL
Minimum required RSRQ of cell for UE to
Minimum required RX quality level (Unit:2dB) QQualMin -18 camp on
Minimum required RSRP for the cell to
Minimum required RX level (Unit:2dBm) QRxLevMin -64 become a candidate during cell reselection. 
Threshold for intra freq measurements configure SIntraSearchCfgInd CFG Enable Intra-Freq measurement
indicator

Intra-freq Reselection Measurement triggering threshold for Intra-

(L2L) Frequency:
Threshold for intra frequency measurements SIntraSearch 29
(Unit:0.2dBm)
CellResel MOD CELLRESEL RSRP<CellResel.QRxLevMin*2+2*CellResel.
SIntraSearch=-70*2+2*29=-70dBm
Hysteresis (4dB) for serving cell when
Hysteresis value for ranking criteria (Unit:dB) Qhyst DB4_Q_HYST ranking
Cell reselection timer value for EUTRAN (Unit:s) TReselEutran 1 Time threshold for EUTRAN cell reselection
6 (L1800)
Cell reselection priority CellReselPriority As plan
5 (L2100)
Minimum required quality level configure indicator QQualMinCfgInd CFG  
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Idle Mode (Inter-Freq Reselection)
•Inter-Frequency reselection will be triggered when UE moves out EutranReselTime

RSRP
of the Higher Priority frequency serving area Ms_L2600
Mn_L700
•UE will reselect to the Higher Priority frequency once the higher - 116dBm
priority frequency fulfill the requirement
●
- 116dBm
- 118dBm

L2L reselection (High to Low) ThreshXLow

Measurement Reselection condition QRxLevMin

trigger RSRP(S)<-118dBm, Reselect to L700 -122dBm
Trigger cell reselection Time
Idle, RSRP(S)<- RSRP(N)>-116dBm, neighbor cell SNonIntraSearch ThreshServLow

116dBm lasts 1s.

EutranReselTime

RSRP
Ms_L700
Mn_L2600
L2L reselection (Low to High)
- 118dBm ●

Measurement Reselection condition

trigger Reselect to L2600
RSRP(N)>-118dBm, neighbor cell
Idle, always lasts 1s.
QRxLevMin
-126dBm Time
ThreshXHigh Trigger cell reselection
Idle Mode (Inter-Freq Reselection)
Recommended
Category Parameter Name MO MML Command Parameter Remark
Value
Minimum required RX level Minimum required RX level (Unit:2dBm) for the cell to
QRxLevMin -64
(Unit:2dBm) become a candidate during cell reselection. 
Threshold for non-intra freq SNonIntraSearchCfgInd CFG Enable Inter-Freq/Inter-RAT measurement
measurements configure indicator
Measurement triggering threshold for scan Inter-
Threshold for non-intra frequency Frequency/Inter-RAT cells:
SNonIntraSearch 9
measurements (Unit:2dBm) RSRP<CellResel.QRxLevMin*2+2*CellResel.SNonIntraSe
arch=-64*2+2*9=-110dBm

Lower priority serving cell starts reselection to Inter-

Inter-Freq Reselection (L2L) CellResel MOD CELLRESEL Frequency/Inter-RAT:
RSRP(S)<CellResel.QRxLevMin*2+2*CellResel.ThrshServ
Serving frequency lower priority ThrshServLow 7 Low=-64*2+2*7=-114dBm
threshold (Unit:2dBm)
The higher this value for high priority layer, the more
difficult for UE to reselect out from the frequency layer.
6 (L1800)
Cell reselection priority CellReselPriority  As plan
5 (L2100)
Speed-dependent reselection SpeedDepReselCfgInd NOT_CFG  
parameter configure indicator
Idle Mode (Inter-Freq Reselection)
Recommended
Category Parameter Name MO MML Command Parameter Remark
Value
 If this parameter is not specified or set to NOT_CFG,
Inter frequency cell resel
CellReselPriorityCfgInd CFG then UE won’t reselect to neighboring cells on the
priority configure indicator frequency
Inter frequency cell resel 6 (L1800)
CellReselPriority  As plan
priority 5 (L2100)

RSRP required for a high priority inter-freq neighboring

cell becomes a candidate for reselection:
RSRP(N)>EUTRANINTERNFREQ
.QRxLevMin*2+EUTRANINTERNFREQ.ThreshXhigh*2=-
Inter frequency high priority ThreshXhigh 11 128+22=-106dBm
threshold (Unit:2dBm)
Note: Ensure this is > Snonintrasearch and > A2 event
(A2ThdRsrp - Hyst) to allow UE has time to look for other
Inter-freq LTE frequency and avoid pingpong reselection.
EutranInterNFreq MOD EUTRANINTERNFREQ
Reselection (L2L)
RSRP required for a low priority inter-freq neighboring
cell becomes a candidate for reselection:
RSRP(N)>EUTRANINTERNFREQ
.QRxLevMin*2+EUTRANINTERNFREQ. ThreshXlow*2=-
Inter frequency lower priority
ThreshXlow 11 128+22=-106dBm
threshold (Unit:2dBm)
Note: Ensure this is > Snonintrasearch and > A2 event
(A2ThdRsrp - Hyst) to allow UE has time to look for other
LTE frequency and avoid pingpong reselection.

Minimum required RX level Minimum required RSRP for the cell to become a
QRxLevMin -64
(Unit:2dBm) candidate during cell reselection
EUTRAN reselection time EutranReselTime 1 Time threshold for inter-frequency cell reselection
(Unit:s)
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Idle Mode (Inter-RAT Reselection, L2U & U2L)
L2U: Only when LTE RSRP < -114dBm and UMTS RSCP > -103dBm lasts for 1 U2L: Once LTE RSRP > -108dBm lasts for 1 second, then reselect to LTE
second, then reselect to UMTS If different reselection priority are set for different LTE frequency, then UE will search the prioritize
frequency first, if no suitable cell then search second priority frequency.
TReselUTRAN
RSRP

Mn_3G TResel

RSRP
Ms_LTE (RSCP)
●
Ms_2G/3G
- 103dBm

Mn_LTE
- 110dBm

- 114dBm - 108dBm

ThreshXLow

QRxLevMin
-128dBm Eqrxlevmin
Time Time
SNonIntraSearch ThreshServLow Trigger cell reselection -128dBm
Trigger cell reselection
ThdToHigh
Reselection
Measurement
condition:
trigger Reselection Reselection condition
RSRP<-114dBm, to UMTS Measurement trigger Reselection to
Idle, RSRP≤- RSRP>-108dBm,
RSCP>-103dBm, lasts automatically LTE
110dBm
1s. lasts 1s

 From 3GPP 25304, UE shall measure all inter-RAT layers with higher priority than serving cell, and reselect to the higher Srxlev cell on the highest priority layer.
 Based on this, if more than one LTE higher priority layers are set in 3G for U to L reselection, UE shall measure all LTE layers regardless they are same or different priority, and reselect to
the highest layer with higher RSRP.

If UE doesn’t support L2100, then it will measure L1800 only then reselect to L18.
 If UE support both L1800 and L2100, UE shall measure both layer.

 
Idle Mode (Inter-RAT Reselection, L2U & U2L)
Category Parameter Name MO MML Command Parameter Recommended Value Remark
Minimum required RX level QRxLevMin -64 Please refer pg.6
(Unit:2dBm)
Threshold for non-intra freq SNonIntraSearchCfgInd CFG Please refer pg.6
measurements configure indicator
CellResel MOD CELLRESEL
Threshold for non-intra frequency
SNonIntraSearch 9 Please refer pg.6
measurements (Unit:2dBm)
Serving frequency lower priority ThrshServLow 7 Please refer pg.6
threshold (Unit:2dBm)
If this option is deselected, reselection
Cell System Information Switch CellSiMap MOD CELLSIMAP Sib6Switch@SiSwitch 1 to UTRAN cells fail.
Cell reselection timer value for TReselUtran 1 Time threshold for L2U cell reselection
UTRAN (Unit:s)
CellReselUtran ADD CELLRESELUTRAN
Speed state scale factor configure SpeedStateSfCfgInd NOT_CFG
indicator
Inter-RAT
Reselection (L2U) Enable cell reselection priority
Reselection priority configure configuration . If reselection priority is
CellReselPriorityCfgInd CFG
indicator not configured , UE won’t reselect to
the 3G frequency.
Cell reselection priority CellReselPriority 3 (U2100)  As plan
Minimum required RSCP for the 3G
Minimum required RX level
QRxLevMin -58 cell to become a candidate during cell
(Unit:2dBm) UtranNFreq MOD UTRANNFREQ reselection.
RSCP required for a low priority 3G
neighboring cell becomes a candidate
UTRAN lower priority threshold for reselection:
ThreshXLow 6
(Unit:2dBm) RSCP(N)>UTRANNFREQ.QRxLevMin*2+
UTRANNFREQ.ThreshXlow*2=-
128+22=-106dBm
Ue inactive timer (Unit:s) RrcConnStateTimer MOD RRCCONNSTATETIMER UeInactiveTimer 20  
Idle Mode (Inter-RAT Reselection, L2U & U2L)
Category Parameter Name MO MML Command Parameter Recommended Remark
Value
SIB Switch UCELLSIBSWITCH MOD UCELLSIBSWITCH SibCfgBitMap 1 SIB19-1
Absolute priority level of the 3 (U2100)
Spriority As plan
serving cell UCELLSELRESEL MOD UCELLSELRESEL 2 (U900)
Reselection delay time (Unit:s) Treselections 1 1 second
NodeBProtclVer UNODEB MOD UNODEB UNODEB R9 NodeB Protocol Version
Reselect to LTE neighbor:
RSRP Threshold for High-prio-freq ThdToHigh 10 RSRP(N)>UCELLNFREQPRIOINFO
Reselection (Unit:2dBm) .EQrxlevmin*2+UCELLNFREQPRIOINFO.Thd
Inter-RAT Reselection (U2L) ToHigh*2=-128+20=-108dBm
RNC:CELL
Minimum required RSRP for the cell to
Minimum Required RSRP Threshold
of the E-UTRA Cell (Unit:2dBm) UCELLNFREQPRIOINFO ADD UCELLNFREQPRIOINFO EQrxlevmin -64 become a candidate during cell
reselection.
E-UTRA Absolute Radio Frequency
EARFCN as plan as plan
Channel Number
Absolute Priority Level of the E- 6 (L1800)
NPriority as plan
UTRA Frequency 5 (L2100)
D50 (L1800) as plan
Measurement Bandwidth EMeasBW D25 (L2100)
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Idle Mode (Inter-RAT Reselection, L2G & G2L)
L2G: Only when LTE RSRP < -114dBm and GSM G2L: Once LTE RSRP > -110dBm during 1 second, then reselect to LTE
RxLev > -101dBm during 1 second, then reselect to GSM If different reselection priority are set for different LTE frequencies, then UE will
search the prioritize frequency first, if no suitable cell then select second priority
TReselGeran
frequency.
RSRP

Mn_2G
TResel
Ms_LTE (RxLev)

RSRP
- 101dBm ●
Ms_2G

- 110dBm Mn_LTE
- 114dBm

- 110dBm

ThreshXLow
QRxLevMin
-128dBm EUTRANQR
Trigger cell reselection Time XLEVMIN
SNonIntraSearch ThreshServLow to GSM -128dBm Time
Trigger cell reselection
ThrEUTRANHigh
to LTE
Reselection condition
Measurement
trigger RSRP<-114dBm, Reselection to Reselection condition
Rxlevel>-101dBm, GSM Measurement trigger
Idle, RSRP≤-110dBm RSRP>-108dBm, Reselection to LTE
lasts 1s. automatically
lasts 5s
Idle Mode (Inter-RAT Reselection, L2G & G2L)
Category Parameter Name MO MML Command Parameter Recommended Value Remark
Minimum required RX level (Unit:2dBm) QRxLevMin -64 Please refer pg.6
Threshold for non-intra freq SNonIntraSearchCfgInd CFG Please refer pg.6
measurements configure indicator
Threshold for non-intra frequency CellResel MOD CELLRESEL
SNonIntraSearch 9 Please refer pg.6
measurements (Unit:2dBm)
Serving frequency lower priority
ThrshServLow 7 Please refer pg.6
threshold (Unit:2dBm)
If this option is deselected, reselection to
Cell System Information Switch CellSiMap MOD CELLSIMAP Sib7Switch@SiSwitch 1 GERAN cells fail.
Cell reselection timer value for GERAN TReselGeran 1 Time threshold for L2G cell reselection
(Unit:s)
CellReselGeran ADD CELLRESELGERAN
Speed state scale factor configure SpeedStateSfCfgInd NOT_CFG  
indicator
Inter-RAT
Reselection Enable cell reselection priority
(L2G) Cell reselection priority configure configuration . If reselection priority is not
CellReselPriorityCfgInd CFG
indicator configured , UE won’t reselect to the 2G
frequency.
Cell reselection priority CellReselPriority 1 As plan
Minimum required RX level for the 2G cell
Minimum required RX level QRxLevMin 0 to become a candidate during cell
(Unit:-115+2*QRxLevMin)
GeranNfreqGroup MOD GERANNFREQGROUP reselection.
Rx level required for a low priority 2G
neighboring cell becomes a candidate for
reselection:
Lower priority threshold (Unit:2dBm) ThreshXLow 7 RSCP(N)>-
115+2*GUIGERANNFREQGROUP
.QRxLevMin+GERANNFREQGROUP
.ThreshXlow*2=-115+14=-101dBm
Idle Mode (Inter-RAT Reselection, L2G & G2L)
Recommended
Category Parameter Name MO MML Command Parameter Remark
Value
LTE Cell Reselection Allowed GCELLHOBASIC SET GCELLHOBASIC LTECellReselEN Yes  
GERAN Priority GERANPRI 1  
UTRAN Priority UTRANPRI 4  
EUTRAN Priority EUTRANPRI 6  
Inter-RAT Search THD Based on Priority MS always searches for neighboring cells in
ThrPriSearch 15
(Unit:-98dBm+ThrPriSearch*3) UTRAN or EUTRAN
Cell Resel Time Hyst Based on PRI
TRESEL 0 5s
Inter-RAT (Unit:5s+TRESEL*5)
Reselection Reselect to LTE neighbor:
GCELLPRIEUTRANSYS SET GCELLPRIEUTRANSYS
(G2L) RSRP(N)>-
BSC:CELL EUTRAN Cell Resel High THD Based on PRI THREUTRANHIGH 10 140dBm+GCELLPRIEUTRANSYS.EUTRANQRXL
(Unit:2dB) EVMIN*2+GCELLPRIEUTRANSYS.THREUTRAN
HIGH*2=-128+20=-108dBm
Min RX Level of EUTRAN Cell Based on PRI Minimum required RSRP for the cell to
EUTRANQRXLEVMIN 6
(Unit:-140dBm+EUTRANQRXLEVMIN*2) become a candidate during cell reselection.
(always), that is, the MS always searches for
EUTRAN Cell Search Thres. in Packet Mode QPEUTRAN 7 neighboring cells in EUTRAN.
Support Cell Reselection GLTENCELL ADD GLTENCELL SPTRESEL SUPPORT Enable cell reselection from GSM to LTE.
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Connected Mode (Handover & MLB & CSFB &
Fast Return)
Macro IBS

L2U CSFB with blind

L1800 (10M) redirection, (Co-sector only,
BlindHoPriority=3)

Coverage based L2U PS

L2100 (5M) L2100 (5M) handover & redirection
(Unidirectional)

REMARK:
U2100 F1 is set as the
U2100 F2 U2100 F2 fallback layer because of its
continuity of coverage.

U2100 F1 U2100 F1

U900 U900 L2G CSFB with blind

redirection (co-sector)

GSM900 GSM900 U2L fast return

Intra-freq Reselection Coverage based Inter-freq MLB based Inter-freq

(Bidirectional) handover (Bidirectional) handover (Co-sector only,
OverlapInd=YES)
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Connected Mode (Coverage Based Intra-RAT
Handover)
Intra-Freq HO will triggered by A3 event if UE moves within LTE Inter-Frequency HO will be triggered when UE moves out of the serving frequency coverage area,
UE will HO to the best cell that fulfill the Inter-Freq HO requirement (A4 event).
same frequency coverage area.
Each UE typically has only one receiver, and consequently one UE can receive the signals on only
one frequency at a time. Therefore, A3 event measurement results cannot reflect signal conditions
in real time. So A4 event is preferred for Inter-Frequency HO.
A1A2TimeToTrig A4TimeToTrig

RSRP
Ms_F1

A4+Hys - 104dBm
●
●
(A4+Hys) >
●
● (A2-Hys) is
A1+Hys - 110dBm
required
to avoid
Measurement
trigger A2-Hys pingpong
Mn_F2
automatically Handover condition handover
Handover to
for every
RSRP(S)<RSRP(N)-2dB, intra-frequency
240ms,
lasts 320ms neighbor cell
(IntraRatHoCo
mm.IntraFreqH Time
oRprtInterval) A2 event A1 event A2 event A4 event

Measurement trigger
HO condition Handover to
automatically,
RSRP(N)>-104dBm, intra-frequency
RSRP(S)<-110dBm,
lasts 640ms neighbor cell
lasts 640ms
 Connected Mode (Coverage Based Intra-RAT
Handover)
Category Parameter Name MO MML Command Parameter Recommended Remark
Value
Handover Algo switch ENodeBAlgoSwitch MOD ENODEBALGOSWITCH IntraFreqCoverHoSwitch@HoAlgoSwitch 1
A3 measurement trigger quantity IntraRatHoComm MOD INTRARATHOCOMM IntraFreqHoA3TrigQuan RSRP
Intra-freq Intrafreq handover hysteresis IntraFreqHoA3Hyst 2 A3 triggering:
Handover (Unit:0.5dB)
RSRP(N)-IntraFreqHoA3Hyst
Intrafreq handover offset IntraFreqHoGroup ADD INTRAFREQHOGROUP >RSRP(S)+IntraFreqHoA3Offset
IntraFreqHoA3Offset 2
(Unit:0.5dB)
Intrafreq handover time to trigger IntraFreqHoA3TimeToTrig 320ms
Downlink EARFCN DlEarfcn As plan As plan 
Measurement bandwidth MeasBandWidth As plan As plan
EutranInterNFreq ADD EUTRANINTERNFREQ
Inter-Freq HO trigger Event Type InterFreqHoEventType EventA4

Handover Algo switch ENodeBAlgoSwitch MOD ENODEBALGOSWITCH InterFreqCoverHoSwitch@HoAlgoSwitch 1

Handover Algo Switch CellHoParaCfg MOD CELLHOPARACFG InterFreqCoverHoSwitch@CellHoAlgoSwitch 1
Interfreq A1A2 hysteresis InterFreqHoA1A2Hyst 2
(Unit:0.5dB)
Interfreq A1A2 time to trigger InterFreqHoA1A2TimeToTrig 640ms
Inter-freq A4A5 Based Interfreq A1 RSRP Stop measurement threshold:
Handover InterFreqHoA1ThdRsrp -105
Threshold RSRP(S)>-105dBm+1=-104dBm
A4A5 Based Interfreq A2 RSRP Start measurement:
InterFreqHoA2ThdRsrp -109
Threshold InterFreqHoGroup ADD INTERFREQHOGROUP RSRP(S)<-109dBm+1=-110dBm
Interfreq handover hysteresis InterFreqHoA4Hyst 2
(Unit:0.5dB)
CoverageBased Interfreq RSRP Handover to neighbour:
InterFreqHoA4ThdRsrp -105
threshold RSRP(N)>-105dBm+1=-104dBm 
Interfreq HandOver Time to InterFreqHoA4TimeToTrig 640ms
Trigger
InterFreq A1A2 Measurement IntraRatHoComm MOD INTRARATHOCOMM InterFreqHoA1A2TrigQuan RSRP
trigger quantity
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Connected Mode (Coverage Based Inter-RAT
L2U Handover)
• The trigger mechanism of L->U (F1) handover triggering is similar to that of Inter-Freq HO, while the threshold are for Inter-RAT
• IRAT B1+Hys > (IRAT 2D event trigger) HO from UMTS to GSM to avoid immediate following HO from UMTS to GSM

IRAT A1A2TimeToTrig B1TimeToTrig

RSRP
Ms_LTE

Sub Triggerin Stopping

Procedure
IRAT B1 + Hys - 102dBm procedure g Events Events
Inter-Rat Event A2 Event A1
- 110dBm (-9dB) measurement
IRAT A1 + Hys - 116dBm (-13dBm) Measurement
Inter-RAT Event B1
- 122dBm (-15dBm) handover
IRAT A2 - Hys Mn_3G
Blind Blind Ho
redirection Event A2
IRAT A2 – Hys
-BlindHoA2ThdOffs Time
et If there is best cell
PS Handover triggered
IRAT A2 event IRAT A1 event IRAT Blind A2 event B1 event

Event A2 trigger Blind redirection trigger:

Event B1 trigger
RSRP<-116dBm or RSRP<-122dBm or RSRQ<-15dB
ECN0>-8dB If there is no best cell
RSRQ<-13dB
Connected Mode (Coverage Based Inter-RAT
L2U Handover)
Category Parameter Name MO MML Command Parameter Recommended Remark
Value
Handover Mode switch ENodeBAlgoSwitch MOD ENODEBALGOSWITCH UtranPsHoSwitch@HoModeSwitch 1  
Handover Mode switch UtranPsHoSwitch@HoModeSwitch 1  
BlindHO A1A2 RSRP
trigger threshold BlindHoA1A2ThdRsrp -121  
(Unit:dBm) CellHoParaCfg MOD CELLHOPARACFG
BlindHO A1A2 RSRQ
trigger threshold BlindHoA1A2ThdRsrq -28  
(Unit:0.5dB)
InterRAT A1A2
hysteresis InterRatHoA1A2Hyst 2  
(Unit:0.5dB)
Inter-RAT InterRAT A1A2 time to
Handover InterRatHoA1A2TimeToTrig 640ms  
trigger
(L2U)
InterRAT A1 RSRP trigger Stop Measurement:
threshold InterRatHoA1ThdRsrp -111 RSRP(S)>-111+2*0.5=-110dBm
(Unit:dBm)
InterRAT A2 RSRP trigger InterRatHoCommGroup MOD INTERRATHOCOMMGROUP Start Measurement:
threshold InterRatHoA2ThdRsrp -115 RSRP(S)<-115-2*0.5=-116dBm
(Unit:dBm)
InterRAT A1 RSRQ Stop Measurement:
trigger threshold InterRatHoA1ThdRsrq -20
RSRQ(S)>-20*0.5+2*0.5=-9dB
(Unit:dB)
InterRAT A2 RSRQ Start Measurement:
trigger threshold InterRatHoA2ThdRsrq -24 RSRQ(S)<-24*0.5-2*0.5=-13dB
(Unit:dB)
Connected Mode (Coverage Based Inter-RAT
L2U Handover)
Category Parameter Name MO MML Command Parameter Recommended Remark
Value
CoverageBased UTRAN ECN0
trigger threshold InterRatHoUtranB1ThdEcn0 -18 Event B1 Triggering:
(Unit:0.5dB) ECN0(N)>InterRatHoUtranB1ThdEcn0*0.
InterRatHoUtranGroupMOD INTERRATHOUTRANGROUP 5+InterRatHoUtranB1Hyst*0.5=-
UTRAN handover hysteresis 18*0.5+2*0.5=-8dB 
InterRatHoUtranB1Hyst 2
(Unit:0.5dB)
Inter-RAT UTRAN time to trigger InterRatHoUtranB1TimeToTrig 640ms  
Handover Utran measurement trigger InterRatHoUtranB1MeasQuan ECN0
(L2U) quantity
BOTH is to trigger measurement event
InterRatHoComm MOD INTERRATHOCOMM A1/A2 with either RSRP or RSRQ .
InterRat A1A2 measurement InterRatHoA1A2TrigQuan BOTH
trigger quantity According to 3GPP TS 36.331, A1A2
trigger quantity could be RSRP or RSRQ.
Inter RAT HO Trigger Event Type InterRatHoEventType EventB1  
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Connected Mode (L2U & L2G CSFB with Blind
Redirection) Recommended
Category Parameter Name MO MML Command Parameter Remark
Value
To shorten the CSFB delay by skipping
IdleCsfbRedirectOptS
Protocol Message an RRC connection reconfiguration
GlobalProcSwitch MOD GLOBALPROCSWITCH witch@ProtocolMsgO 1
Optimization Switch procedure during blind redirection for
ptSwitch
CSFB
UTRAN is highest priority for CSFB. For
Highest priority InterRat InterRatHighestPri UTRAN GL UE, it will be CSFB to GERAN
Second priority InterRat InterRatSecondPri GERAN  
CSFallBackBlindHoCfg MOD CSFALLBACKBLINDHOCFG
CSFB Highest priority IdleCsfbHighestPri UTRAN  
InterRat for Idle UE
Second priority InterRat IdleCsfbSecondPri GERAN  
CSFB Highest Priority InterRAT InterRatHighestPri UTRAN  
(L2U & L2G Blind
Redirection) Second Priority InterRAT InterRatSecondPri GERAN  
CSFB Highest Priority CellOpHoCfg ADD CELLOPHOCFG IdleCsfbHighestPri UTRAN  
InterRAT for Idle UE
CSFB Second Priority IdleCsfbSecondPri GERAN  
InterRAT for Idle UE
Frequency Priority for
UtranNFreq MOD UTRANNFREQ ConnFreqPriority 3  
Connected Mode
Blind handover priority UtranNCell MOD UTRANNCELL BlindHoPriority 3 Co-sector only
Frequency Priority for GeranNfreqGroup MOD GERANNFREQGROUP ConnFreqPriority 3  
Connected Mode
Blind handover priority GeranNcell MOD GERANNCELL BlindHoPriority 3 Co-sector only
 Connected Mode (L2U & L2G CSFB with Blind
Redirection)
Category Parameter Name MO MML Command Parameter Recommended Value Remark
UtranCsfbSwitch@HoAlgoSwitch 1
Handover Algo switch
GeranCsfbSwitch@HoAlgoSwitch 1
ENodeBAlgoSwitch MOD ENODEBALGOSWITCH UtranRedirectSwitch@HoModeSwitch 1
Handover Mode GeranRedirectSwitch@HoModeSwitch 1
switch
CSFB BlindHoSwitch@HoModeSwitch 1
(L2U & L2G Handover Allowed UtranCsfbSwitch@HoAllowedSwitch 1 Enable blind
CellAlgoSwitch MOD CELLALGOSWITCH
Blind Switch GeranCsfbSwitch@HoAllowedSwitch 1 redirection for CSFB
Redirection) UtranRedirectSwitch@HoModeSwitch 1
Handover Mode CellHoParaCfg MOD CELLHOPARACFG GeranRedirectSwitch@HoModeSwitch 1
switch
BlindHoSwitch@HoModeSwitch 1
CSFB handover policy CsfbHoPolicyCfg REDIRECTION, CCO_HO, PS_HO REDIRECTION-1&CCO_HO-0&PS_HO-0
MOD CSFALLBACKPOLICYCFG
Configuration IdleModeCsfbHoPolicyCfg REDIRECTION, CCO_HO, PS_HO REDIRECTION-1&CCO_HO-0&PS_HO-0

Category Parameter Name MO MML Command Parameter Recommended Value Remark

L2G CSFB CSFB Support GCELLSOFT SET GCELLSOFT SUPPORTCSFB SUPPORT Enable L2G CSFB 
BSC:CELL
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Connected Mode (U2L & G2L Fast Return)
Parameter Recommended
Category MO MML Command Parameter Remark
Name Value

HO_UMTS_TO_
HandOver UCORRMALGOSWIT SET UCORRMALGOSWITCH HoSwitch LTE_FAST_RETU UE can fast return to the LTE network after its RRC connection is
Switch CH RN_SWITCH-1 released in the UMTS network
U2L Fast
Return
RNC:RNC Performance PERFENH_PS_F
PerfEnhanceSwitch3 AST_RETURN_L Enable RNC releases the RRC connection when a CS fallback UE keeps a
Enhancement UCORRMPARA SET UCORRMPARA PS connection after terminating a call.
Switch 3 TE_SWITCH-1

HO_UMTS_TO_ can fast return to the LTE network after its RRC connection is
LTE_FAST_RETU UE
RN_SWITCH-1 released in the UMTS network
U2L Fast Fast Return To
Return UCELLHOCOMM ADD UCELLHOCOMM FastReturnToLTESwitch
RNC:CELL LTE Switch PERFENH_PS_F
AST_RETURN_L Enable RNC releases the RRC connection when a CS fallback UE keeps a
PS connection after terminating a call.
TE_SWITCH-1
 Connected Mode (U2L & G2L Fast Return)
Recommended
Category Parameter Name MO MML Command Parameter Remark
Value
L2U CSFB CSFB Support GCELLSOFT SET GCELLSOFT SUPPORTCSFB SUPPORT Enable L2G CSFB
BSC:CELL
HO_UMTS_TO_
SET
HandOver Switch UCORRMALGOSWITCH HoSwitch LTE_FAST_RETUUE can fast return to the LTE network after its RRC
UCORRMALGOSWITCH
U2L Fast Return RN_SWITCH-1 connection is released in the UMTS network
RNC:RNC PERFENH_PS_F
Performance PerfEnhanceSwitch3 AST_RETURN_LEnable RNC releases the RRC connection when a CS
UCORRMPARA SET UCORRMPARA
Enhancement Switch 3 fallback UE keeps a PS connection after terminating a call.
TE_SWITCH-1
HO_UMTS_TO_ can fast return to the LTE network after its RRC
Fast Return To LTE FastReturnToLTESwitch LTE_FAST_RETUUE
Switch
U2L Fast Return RN_SWITCH-1 connection is released in the UMTS network
UCELLHOCOMM ADD UCELLHOCOMM
RNC:CELL PERFENH_PS_F
Fast Return To LTE FastReturnToLTESwitch AST_RETURN_LEnable RNC releases the RRC connection when a CS
Switch fallback UE keeps a PS connection after terminating a call.
TE_SWITCH-1
Support Blind fast return (save 10s compare with measurement),
Measurement-based GCELLPRIEUTRANSYS SET GCELLPRIEUTRANSYS FASTRETURNMEASSPT OFF co-sector only
Fast LTE Reselect
Eutran CellId consists of a 20-bit eNodeBID and an 8-bit
Cell CI CI As plan
G2L Blind Fast Return CellID (EutranCellId = eNodeBID x 256 + CellID)
BSC:CELL Track area code GEXTLTECELL ADD GEXTLTECELL TAC
EARFCN FREQ As plan As plan
Physical Cell ID PCI
Support Rapid
GLTENCELL ADD GLTENCELL SPTRAPIDSEL SUPPORT Enable quick G2L reselection.
Reselection
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
Connected Mode (Inter-Freq MLB)
Category Parameter Name MO MML Command Parameter Recommended Value Remark
Intra-eNodeB HO Static Switch GlobalProcSwitch MOD GLOBALPROCSWITCH IntraEnodebHoStaticSw ON  
MLB Algorithm Switch ENodeBAlgoSwitch MOD ENODEBALGOSWITCH INTER_FREQ_IDLE_MLB_SWITCH@MlbAlgoSwitch 1  
Inter Frequency Idle MLB Mode eNodeBMlb MOD ENODEBMLB ADAPTIVE_PROPORTION@InterFreqIdleMlbMode 1  
Mobility Load Balancing Trigger
MlbTriggerMode UE_NUMBER_ONLY  
Mode
Inter-frequency Mobility Load 100 (L1800)
InterFreqMlbUeNumThd  
Balancing UE Number Threshold 50 (L2100)
Inter-Freq Idle MLB UE Number 100 (L1800)
InterFreqIdleMlbUeNumThd  
Threshold 50 (L2100)
Inter-Freq MLB Mobility Load Balancing UE MlbUeNumOffset 15  
(Co-sector only) Number Offset
Ue Number Difference CellMLB MOD CELLMLB
UeNumDiffThd 15  
Threshold
SynchronizedUE@InterFreqUeTrsfType 1  
InterFreq MLB Transfer Type
IdleUE@InterFreqUeTrsfType 1  
Inter-frequency Load Evaluate InterFreqLoadEvalPrd 15  
Period
Idle MLB UE Number Difference IdleMlbUeNumDiffThd 15  
Threshold
Mlb Ho Cell select Strategy MlbHoCellSelectStrategy ONLY_STRONGEST_CELL  
Connected Mode (Inter-Freq MLB)
Parameter Recommended
Category MO MML Command Parameter Remark
Name Value
Load balancing InterFreqMlbSwitch@MlbAlgoSwitch 1  
algorithm InterFreqBlindMlbSwitch@MlbAlgoSwitch 0  
switch InterFreqIdleMlbSwitch@MlbAlgoSwitch 1  
CellAlgoSwitch MOD CELLALGOSWITCH
Enhanced MLB SpectralEffBasedLoadEvalSw@EnhancedMlbAlgoSwitch 1  
Algorithm
Switch DediPrioManageOnLowLoadSw@EnhancedMlbAlgoSwitch 1  
Inter-Freq MLB Mobility Load
(Co-sector only) Balancing
EutranInterNFreq MOD EUTRANINTERNFREQ MlbTargetInd ALLOWED  
Target
Indicator
Overlap
Indicator EutranInterFreqNCell MOD EUTRANINTERFREQNCELL OverlapInd YES Co-sector only
Timer320 for RrcConnStateTimer MOD RRCCONNSTATETIMER T320ForLoadBalance min10  
load balance
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2
2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB
3 4T4R
4 Appendix
4T4R
DL 4x4 MIMO:
This feature configures four antenna ports for both eNodeBs and UEs for downlink transmission and adaptively
selects transmit diversity or spatial multiplexing for each UE to increase downlink throughput and improve
coverage performance.
Compared with 2x2 MIMO and 4x2 MIMO, this feature doubles the downlink peak rate, raises downlink throughput,
improves coverage performance, and provides better user experience.

DL 4x2 MIMO:
This feature configures four antenna ports for downlink transmission and adaptively selects transmit diversity or
spatial multiplexing for each UE to increase downlink throughput and improve coverage performance.
4x2 MIMO differs from 2x2 MIMO in the following aspects:
• Transmits additional reference signals over antenna ports 2 and 3.
• Performs frequency switched transmit diversity (FSTD) in addition to space frequency block coding (SFBC).
• Uses a separate codebook that contains 16 precoding matrixes for closed-loop MIMO.
4T4R
Category Parameter Name MO MML Command Parameter Recommended Value Remark
MIMO Adaptive CellMimoParaCfg MOD CELLMIMOPARACFG MimoAdaptiveSwitch CL_ADAPTIVE  
Switch
Initial Mimo Type CellMimoParaCfg MOD CELLMIMOPARACFG InitialMimoType ADAPTIVE  
DL schedule switch CellAlgoSwitch MOD CELLALGOSWITCH FreqSelSwitch@DlSchSwitch OFF  
DL schedule switch CellAlgoSwitch MOD CELLALGOSWITCH AperiodicCqiTrigOptSwitch@DlSchSwitch ON  
maximum number CellDlschAlgo MOD CELLDLSCHALGO MaxMimoRankPara SW_MAX_SM_RANK_4  
of MIMO layers
Reference signal
PDSCHCfg MOD PDSCHCFG ReferenceSignalPwr 182  
power
PB PDSCHCfg MOD PDSCHCFG Pb 0  
Reduce RBLER eNBCellRsvdPara MOD ENBCELLRSVDPARA RsvdSwPara3_bit6@RsvdSwPara3 ON  
switch
4T4R
Compatibility ENodeBAlgoSwitch MOD ENODEBALGOSWITCH Tm3Tm4Max4LayerCtrlSwitch@Compatibility ON  
Control Switch CtrlSwitch
CQI Period Adaptive CellCqiAdaptiveCfg MOD CELLCQIADAPTIVECFG CqiPeriodAdaptive ON  
Switch
Handover Aperiodic CellCqiAdaptiveCfg MOD CELLCQIADAPTIVECFG HoAperiodicCqiCfgSwitch ON  
CQI Config Switch
SimulAckNackAndC CellCqiAdaptiveCfg MOD CELLCQIADAPTIVECFG SimulAckNackAndCqiSwitch ON  
QI Config Switch
For the UE which only support
aperiodic CQI reports in 3-1 reporting
Top UE avoidance ENodeBAlgoSwitch MOD ENODEBALGOSWITCH ApCqiAndAckAbnCtrlSwitch ON mode and ACKs/NACKs are
transmitted simultaneously.
Contents
1 Idle Mode
Intra-Freq
Intra-Freq Reselection
Reselection
Inter-Freq
Inter-Freq Reselection
Reselection
Inter-RAT
Inter-RAT Reselection,
Reselection, L2U
L2U &
& U2L
U2L
Inter-RAT
Inter-RAT Reselection,
Reselection, L2G
L2G &
& G2L
G2L

2 Connected Mode
Coverage
Coverage Based
Based Intra-RAT
Intra-RAT Handover
Handover
Coverage
Coverage Based
Based Inter-RAT
Inter-RAT L2U
L2U Handover
Handover
L2U
L2U && L2G
L2G CSFB
CSFB with
with Blind
Blind Redirection
Redirection
U2L
U2L && G2L
G2L Fast
Fast Return
Return
Inter-Freq
Inter-Freq MLB
MLB

3 Appendix
Appendix
Major Network Elements and version
NE name NE version
LTE eNodeB eRAN11.1
UMTS RNC RAN17
GSM BSC RAN17

Parameter List & Planning EP

Parameter Lis t LTE EP_PH-1

164+460 New s ites 20161130_V1
Appendix
Scope

Parameter Range Remark

PCI 0 ~ 503

RSI 0 ~ 837

TAC 0 ~ 65535

eNodeB Name 1 ~ 64 characters

eNodeB ID 0 ~ 1048575

Cell Name 1 ~ 99 characters

Cell ID ID NO. of 0 ~ 255

Appendix
PCI & RSI Planning (0 ~ 503)

Total PCIs
PCI Groups Total PCIs PCI Range Current Usage
Macro IBS Reserved

Macro 450 0 to 449 0 to 404

6% 5%

IBS 30 450 to 479 450 to 479

Reserved 24 480 to 503 - 89%

Appendix
RSI Planning (0 ~ 837)
Radius Macro ： 8000m IBS: 2000m

Total RSIs
Current
Macro IBS Reserved
RSI Group RSI Range range
Macro 0 to 727 0 to 685
7%
6%
IBS 728 to 777 728-776
Reserved 778 to 837 -
87%
Appendix
TAC Planning (0 ~ 65535)

Digit 5 Digit 4 Digit 3 Digit 2 Digit 1

Region Code
Yangon 00~02
1. 5th Digit represent technology like 2 for GSM, 3 for UTRAN, 4 for Ayeyarwady 03
LTE Bago East 04
Naypyitaw 05
2. 4th & 3rd Digit represent Place
Shan South 06
3. 2nd & 1st Digit represent TAC NO. Mon 07
Thanintharyi 08
Example Rakhine 09
Bago West 10
4 0 0 0 1 Kayin 11
Shan East 12
LTE Yangon TAC NO. Kayah 13
Appendix
TAC-LAC Mapping
Principle
In LTE, the core network paging is based on the TAL ， 2G/3G is
based on LAC. TAL and LAC paging features roughly, So the use of
TAL and LAC mapping. Currently, the core network product
specifications are as follows:

• A core network can plan any number of TAL, 1 TAL can

accommodate 16 TAC.

• 1 TAC can accommodate 30~100 eNodeB.

XXXX LAC
• Taking into account the amount of signaling, paging
performance and the need for future expansion, this limit is not
in accordance with product specifications configuration. XXXXX TAC

TAL consistent with LAC mapping using boundary

Appendix – TAC & LAC Mapping
TAL LAC Site No. TAC
1 351 142 40001 40002 40003 40004 40005
2 352 84 40006 40007 40008 　 　
3 353 76 40009 40010 40011 　 　
4 354 95 40012 40013 40014 　 　
5 355 51 40015 40016 　 　 　
6 356 95 40017 40018 40019 　 　
7 357 128 40020 40021 40022 40023 　
8 358 94 40024 40025 40026 　 　
9 359 62 40027 40028 　 　 　
10 360 88 40029 40030 40031 　 　
11 451 79 　 　 　 　 　
12 452 80 　 　 　 　 　
13 551 151 　 　 　 　 　
LTE TAC-LAC
14 552 110 　 　 　 　 　 information20161115_Update
15 651 325 　 　 　 　 　
16 751 200 　 　 　 　 　
17 781 128 40701 40702 40703 40704 　
18 782 122 40705 40706 40707 40708 　
19 783 92 40709 40710 　 　 　
20 3051 131 40501 40502 40503 40504 40505
21 3052 95 40506 40507 　 　 　
22 3251 239 　 　 　 　 　
23 3351 50 　 　 　 　 　
24 3451 64 　 　 　 　 　
25 3551 153 　 　 　 　 　
26 3552 20 　 　 　 　 　
Appendix
eNodeB Name Macro

eNodeB Name (1~64 characters)

Digit 10 Digit 9 Digit 8 Digit 7 Digit 6 Digit 5 Digit 4 Digit 3 Digit 2 Digit 1

Note:
1. 10th Digit–Technology like G for GSM, U for UTRAN, L for LTE proposed to
add one
2. 2nd Character for T-2100, E-1800, S-700, F-450 MHZ more digit
to identify
3. 3rd ,4th & 5th Character – region Name Short Code like for Yangon it can be “YGN” Macro,
micro, IBS,
4. 6th ,7th , 8th, 9th & 10th character for internal  id Pico. Pls
suggest if
need.
Example

L T Y G N 0 0 0 0 1

LTE 2100
Yango Internal ID, which follows it of QROI
MHZ
n ID
Appendix Cell name & ID

eNodeB Name IBS

eNB name & ID LBYGN01011
AA
01201211

LBYGN0101 LBYGN01011
1A AB
012012 01201212

…
LBYGN0101
1 LBYGN01011
BA
01201311

YGN01011B LBYGN01011
BB
012013 01201312

…
Appendix
eNodeB ID (Marco & IBS)
eNodeB ID (0~1048575)
Region Code
Digit 6 Digit 5 Digit 4 Digit 3 Digit 2 Digit 1 YGN 01
AWD 02
BGE 03
1. 5 and 6th Digit –Present BGW 04
2. 4,3,2,1 represent exiting NodeB ID MON 05
KYN 06
Example TNY 07
NPT 08
SHS 09
0 1 0 0 1 1 SHE 10
KYH 11
Region code RKE 12
Existing NodeB ID
Appendix
Cell Name & ID

EUTRAN Cell Name (1~99 characters) EUTRAN Cell ID ( ID NO. of 0 ~ 255 ）

eNodeB eNodeB ID Digit 2 Digit 1
Digit 2 Digit 1
Name
1. First part is eNodeB name 1. First part is eNodeB ID

2. Digit 2 will be filled by character 2. Digit 2 & 1 represent cell ID NO. 1800Mhz is
A,B,C,D…,which is represent sector ID planned to be 01,02,03…, 2100 Mhz is
11,12,13…
3. Digit 1 will be filled by number which is
represent to carrier. 1800Mhz is planned to be
1, 2100Mhz is 2

Example Example

LXYAG0000 010011 01
A 1
1
eNodeB Sector Carrier eNodeB ID Cell 1
Name A 1
Appendix – RS Power Configuration
RS power distribution
One RB include 12 Subcarriers and 7 symbol, Time slot is 0.5ms.

a). For the symbol with RS , there are 2*RS element, 2*Null element, 8
normal resource element.

b). For the symbol without RS, there are 12 normal resource element

What’s meaning of PAPB?

PA,PB indicates power distribution between RS

element and normal RE

Power of RE=(PA)*(PB)*RS power

Notice: Configuration of M2000 for PA, PB is GUL value,

here I use (PA)&(PB) to represent physical value.
Appendix – RS Power Configuration
 Symbols will be sent out for moment by moment, and we suppose network bandwidth is 20Mhz with 100
RBs.

So, if we configure PA,PB as (-3,1) and set RS power is 18.2dBm(0.066W)

a). For the symbol with RS, total power for one RB is
Tot=2*RS+8*RE=2RS+8*(PA)*(PB)*RS
As per relevant definition in 3GPP protocol, (PA)=1/2, (PB)=1, so
Tot=2RS+8*1/2*1*RS=6*RS
Now we have 100 RBs, so total power for whole bandwidth is
100*6*RS=100*6*0.066W40W

b). For the symbol without RS, total power for whole bandwidth is
Tot=100*12*RE=100*12*(PA)*(PB)*RS=100*6*RS40W
PB physical value Symbol Symbol
Bandwidt Rs
PBOne Anteena Two or Four Anteena PA,PB with RS without RS
port port
h power
power power
0 1 5/4 (-3,1) 10Mhz 18.2dBm 20W 20W
1 4/5 1
2 3/5 3/4 (0,0) 10Mhz 18.2dBm 40W 40W
3 2/5 1/2 (-3,1) 10Mhz 15.2dBm 10W 10W
PA physical value=10^(PA GUL (0,0) 10Mhz 15.2dBm 20W 20W
value)