V4i4 1287

Verma Akanksha; International Journal of Advance Research, Ideas and Innovations in Technology
ISSN: 2454-132X
Impact factor: 4.295
(Volume 4, Issue 4)
Available online at: www.ijariit.com
Powder metallurgy: Advanced techniques and applications
Akanksha Verma
[email protected]
Institute of Engineering and Technology, Lucknow, Uttar Pradesh
ABSTRACT
In this paper, a brief review about the advancement in powder metallurgy process along with their applications as well as
problems faced during the research is discussed. The main objective of this paper is to accentuate the applications of advanced
powder metallurgy technology in various fields and also to encourage the readers to understand and write more papers on such
issues. Advanced Powder Metallurgy is also known as metal injection moulding (MIM) technology helpful for forging complex
shaped components with a low investment of money. Therefore, a forming technology applied to form new materials by diffusion
of different metals as well as ceramic powders as raw ingredients through sintering (temperature below the melting point) is
known as powder metallurgy. The most advantageous thing of this process is that the powder can easily be shaped directly into
the end product and also possesses a significant degree of freedom in the composition of materials, properties, microstructure
and thermal processing. Powder Metallurgy provides such properties that cannot be achieved by the melting process.
Advancement in Powder Metallurgy technique is a standard allusion for the engineers in the metal forming industries that use
powder metallurgy with a research interest in the field.
Keywords— Metal injection moulding, Diffusion of metals, Sintering, Complex shaped components, Thermal processing
1. INTRODUCTION
Powder metallurgy is a general metal forming technique applied to produce dense and precision components. It is regarded with the
production of metal powders and commensurates them to the desired shape. In this kind of technique, the particulate materials are
bonded to semi-finished and finished products. On the other hand, direct laser forming (DLF) technique is another advanced powder
processing technique. Steps in the process of powder metallurgy are shown in the following given figure:
Fig. 1: Powder metallurgy process

© 2018, www.IJARIIT.com All Rights Reserved Page | 425
Verma Akanksha; International Journal of Advance Research, Ideas and Innovations in Technology
2. PRINCIPLES OF POWDER METALLURGY
The long-established powder metallurgy process involves the blending of the metal powders and other constituents by compaction
and sintering to obtain desired size and shape. The two stages of compaction are fused into a single step in hot pressing. Some of
the problems occurred during die-compaction and compaction of sintering in traditional powder metallurgy technique can be
overcome by newly developed isostatic compaction method.
3. MATERIALS AND PROCESSES IN POWDER METALLURGY

3.1 Titanium:- Hot Isostatic pressing (HIP), Injection moulding
3.2 Superalloy and steel:- Spray Forming
3.3 Aluminide, Nickel:- Reaction sintering and Extrusion
3.4 Iron alloy:- Powder Forging
3.5 Stainless steel:- Cold isostatic pressing (CIP)
3.6 Solidified aluminum alloy:- Complete densification method
4. APPLICATIONS OF POWDER METALLURGY

4.1 Gears, bearings and connecting rods (for automobiles)
4.2 Produce cutting/abrasion resistant tooling materials such as cemented carbide tip and moulding
4.3 Porous materials such as filters and implants for living bodies
4.4 Materials for pantograph contact strips
4.5 Sensor rings
4.6 Aircraft structuring
4.7 Fine jewellery/accessories
4.8 Cutting Tools and Dies
4.9 Anticorrosive component
4.10 Dynamic membranel filter
5. FUTURE DEVELOPMENTS
5.1 Structural parts: To enhance the strength of sintered materials, nickel and molybdenum have been mixed to achieve the high
hardness. As the chromium is the most effective element for the improvement of hardness and strength of steel and because Cr
is not so expensive, we can obtain high-strength materials at very low cost.
5.2 Magnetic parts: Recently, we are seeking to initiate the new applications of magnetic materials to support the enhancement in
the demand for electric cars. This will be done by improving magnetic properties and advancing the techniques for development
of net shaping methods in order to produce cores that are more difficult to be formed.
5.3 Next-Generation High-Performance parts: For the continuous advancement of Powder Metallurgy industry, the trend
towards reaching higher relative density levels should be emphasized. There has been an increasing trend in the usage of high-
density Powder Metallurgy steels over the last decades. To maintain the future development of Powder Metallurgy and
competitiveness with the other manufacturing processes, reaching full or near-full density is a key factor.
5.4 Powder Lamination 3D:- Ti powder laser forming is now an advanced method to improve the relative density and accuracy
of the product.
6. CONCLUSION
After studying the whole research paper, in the end, we come to the conclusion that, in recent, metal injection moulding (MIM) and
powder lamination 3-D printing are brought as new powder forming techniques. Producing large products is still difficult because
of deformation due to their own weight during the debinding process and long processing time. If these problems are resolved then
the scope of application is expected to be greatly expanded. Contrarily, metallic powder lamination 3D printing has just come into
the trend with the efficiency of forming complicated structures and shapes on the outer as well as the inner side. The roughness of
the side surfaces and entire dimensional accuracy need to be improved. Some of the problems are associated with the volume
production but this powder metallurgy technique is different and unique from a manufacturing point of view. Now, at last, based on
the whole study the further advancement and development is needed to be very much upgraded
7. REFERENCES
[1] Introduction and materials used in powder metallurgy by Hideshi MIURA (Professor, Department of Mechanical Engineering,
Kyushu University) NTN TECHNICAL REVIEW No.82（2014)
[2] Applications of powder metallurgy by Hideshi MIURA (Professor, Department of Mechanical Engineering, Kyushu
University) NTN TECHNICAL REVIEW No.82（2014)
[3] Future developments by Tadayuki Tsutsui, Hitachi Powdered Metals Co., Ltd.(Review Paper), Technical report no. 54
© 2018, www.IJARIIT.com All Rights Reserved Page | 426

V4i4 1287

Uploaded by

Copyright:

Available Formats

V4i4 1287

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

V4i4 1287

Uploaded by

Copyright:

Available Formats

Verma Akanksha; International Journal of Advance Research, Ideas and Innovations in Technology

Fig. 1: Powder metallurgy process

3. MATERIALS AND PROCESSES IN POWDER METALLURGY

4. APPLICATIONS OF POWDER METALLURGY

© 2018, www.IJARIIT.com All Rights Reserved Page | 426

You might also like