How to install

your ecobee
room sensor
In here you’ll find ways
to set up your room sensor:
— Pairing with your thermostat
— Placing your room sensor
— Troubleshooting
STE P 1: PA I R I N G ST E P 2 : PA I R I N G

To set up your room sensor, ensure that Pull the plastic tab on your room sensor
your ecobee is awake by either standing and it will power connect to your ecobee
in front of it or touching the screen. automatically.

Room Sensor (BBRK)

You appear to have a room sensor

installed. Would you like to pair it
with your ecobee?

72 72

No Yes
STE P 3 : PA I R I N G ST E P 1 : P L AC E M E N T

Continue to finish your sensor set-up. There are two ways that you can place
the sensor: mount it on a wall or place it on
a flat surface.

OPTION 1: WALL OPTION 2: FLAT SURFACE

Attach using the screw provided. Attach the stand by removing the smaller
back cover and popping the stand into place.

Rename

To rename this sensor, you can

choose from one of these names or
create your own.

Custom Name
Home

Bedroom

Upstairs To remove the stand, pull the base outwards.

Downstairs

Cancel Next
ST E P 2 : P LAC E M E N T ST E P 3 : P L AC E M E N T

If you are placing your room sensor on If you are placing your room sensor on a
a wall: flat surface:
Place it at a height of approximately 5ft / 1.5m on an interior wall. Place on a flat surface using the stand provided.
Place away from direct heat/cool sources, such as a fireplace or air vent. Make sure it is facing the room, instead of the wall

5 ft
(1.5m)

TIP The bee should always be facing upwards. TIP The bee should always be facing upwards.
TR O UB L E S HOOT I N G T R O U B L E S H O OT I N G

If your sensor does not pair with If your thermostat is showing “N/A”:
your ecobee: Your sensor is out of range. Try moving it closer to the thermostat.
When in range, they will connect automatically.
1. Remove the battery.
2. Wait 2 minutes.
3. Re-insert the battery to restart
the detection process.

45 ft

NOTE T
 o access the battery, pop the room sensor back cover off using the
ridges provided.
Room Sensor Specifications Change or modifications that are not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
Model No: EBRSE4-01
FCC ID: WR9EBRSE4 RF Exposure Information:
IC: 7981A-EBRSE4
Dimensions: 44x44x20 mm without the stand. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
53 mm tall when mounted on the stand environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure
Wireless band: 915 MHz limits, human proximity to the antenna shall not be less than 20cm during normal operation.
Power source: CR2032 watch battery
Operating conditions: Operating Temperature: 0˚C to 40˚C Industry Canada (IC)
Operating Humidity: 20% to 80% RH Compliance Notice:

FCC Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s).
Compliance Notice: Operation is subject to the following two conditions:
1. This device may not cause interference, and
This equipment has been tested and found to comply with the limits for a Class B digital 2. This device must accept any interference, including interference that may cause undesired
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable operation of the device.
protection against harmful interference in a residential installation. This equipment generates, This Class B digital apparatus complies with Canadian ICES-003.
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there RF Exposure Statement:
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by This equipment complies with IC RSS-102 radiation exposure limits set forth for an
turning the equipment off and on, the user is encouraged to try to correct the interference uncontrolled environment. This transmitter must be installed to provide a separation distance
by one or more of the following measures: of at least
– Reorient or relocate the receiving antenna. 20 cm from all persons and must not be collocated or operating in conjunction with any
– Increase the separation between the equipment and receiver. other antenna or transmitter.
–C onnect the equipment into an outlet on a circuit different from that to which the receiver
is connected. Warning: Changes or modifications not expressly approved by ecobee Inc. could void the
– Consult the dealer or an experienced radio/TV technician for help. user’s authority to operate the equipment.

This device complies with part 15 of FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
We’re here to help.
ecobee.com
[email protected]

1.877.932.6233
© 2016 ecobee, Inc. All rights reserved. ecobee
and the ecobee logo are trademarks of ecobee Inc.,
registered in the U.S. and other countries.
EB-RSE3PK2-01
770-00045