2022 SPEED CONCEPT

SERVICE MANUAL SUPPLEMENT

 2022 Speed Concept SLR/TT

Contents

Brake/shift routing — Brake routing — eTap T47 bottom bracket Headset and basebar/ Cockpit — towers
Di2 stem

Cockpit — aerobars Cockpit — install the Seatpost — SLR Seatpost — TT IsoSpeed — SLR
towers and aerobars

Chainkeeper Accessories — SLR Specifications

Safety Legend
WARNING
Apply grease
Properly tighten hardware
Always tighten hardware to the specified torque.
Over-tightening hardware could deform or break the
hardware or components. Under-tightening hardware
could cause hardware or components to become loose. Do not apply grease
Either situation could damage the bicycle and result in
injury to the rider.
Apply threadlocker
WARNING
Reapply threadlocker Nm Torque
All reused-fasteners with pre-applied threadlocker must
be cleaned with isopropyl alcohol and have new thread-  Zip tie
locker applied before re-assembly. If threadlocker is not
applied, the fasteners may loosen which could damage
the bicycle and result in injury to the rider.

Copyright 2022 Trek Bicycle Corporation All Rights Reserved

1
 2022 Speed Concept SLR/TT

About this manual

Rider must be measured before assembling this bicycle
This bicycle features a custom fit and parts specific to the rider’s proportions. Before purchasing this bicycle, you must have
been fit using the online Speed Concept Fit Finder.

Order of assembly
This manual follows an order of assembly starting with a bare frame (e.g., you route the rear brake hose before installing the
bottom bracket). Certain build portions may have been completed already — skip to the section you need.

Scope of this manual

This manual does not contain detailed instructions for components not produced by Trek, such as shift levers and brake
calipers. Refer to the original manufacturer for more information.

Experienced bicycle mechanics required

These instructions are written for an experienced bicycle mechanic. The high-tech design of this bicycle requires precision and
the proper tools. If you are doing your own maintenance, consult your dealer for any issues.

SLR TT

2
 2022 Speed Concept SLR/TT

Brake/shift routing — Di2

10

9
4-6Nm
11

4
3
7 8

1
0.7Nm 2 5.2Nm 5
6

1 Rear derailleur hanger — W524188 Route the brake hoses

1. Connect the calipers to the brake hoses.
2 Rear derailleur hanger bolts — W524884
2. Route the rear brake hose through the grommet
3 Rear brake grommet — W330578 (3) and foam sleeve (8). Route both brake hoses as
shown below.
4 Front shift wire grommet — W326042

5 Front derailleur bolts — W5263897 3

6 Front derailleur hanger — W5257283 8

7 Rear Di2 shift wire grommet — W317292

8 Foam housing sleeve (60cm) — W528082

9 Battery mount — W5255420 3. Loosely attach the calipers to the chainstay and fork
(this keeps the hoses from sliding out).
10 Battery o-ring 5294345

11 Battery mounting screw

3
 2022 Speed Concept SLR/TT

Brake/shift routing — Di2 (continued)

Route the shift wires Di2 wiring overview
1. Route and connect the three wires to the battery as
shown below.
TIP: Tape the wire sticking out of the head tube to the
outside of the frame.

9
12

13
7

2. Insert the battery mount assembly into the seatpost 14

and install the mounting screw (11).

Front derailleur

11
4-6Nm

15
Rear derailleur
3. Insert the seatpost into the seatmast.
4. Attach the derailleurs to the frame. Connect the shift
wires to the derailleurs.

12 Junction B — SM-JC41

13 Conversion adaptor — EW-AD305

14 Y-split — EW-JC130

15 Battery — BTDN300

4
 2022 Speed Concept SLR/TT

Brake routing — eTap

3
6 7

1
0.7Nm 2 5.2Nm 4
5

1 Rear derailleur hanger — W524188 Route the brake hoses

2 Rear derailleur hanger bolts — W524884 1. Connect the calipers to the brake hoses.
2. Route the rear brake hose through the grommet
3 Rear brake grommet — W330578 (3) and foam sleeve (7). Route both brake hoses as
shown below.
4 Front derailleur bolts — W5263897

5 Front derailleur hanger — W5257283

3
6 Rear grommet plug — W547906
7
7 Foam housing sleeve (60cm) — W528082

3. Loosely attach the calipers to the chainstay and fork

(this keeps the hoses from sliding out).

5
 2022 Speed Concept SLR/TT

T47 bottom bracket

Install the bottom bracket Spacers required
1. Apply grease to the threads on both sides of the The table below contains bottom bracket/crank
frame. combinations that require spacers. Your bicycle may have
other combinations that do not require spacers.
Spacers required
Crank Bottom bracket Drive Non-drive
side side
CeramicSpeed
Shimano 0.5mm 0.5mm
24mm
DUB SRAM DUB 2-3mm —
SRAM
GXP Wheels MFG 1.0mm —

2. Using your hands, thread the bottom bracket onto driveside non-driveside
the frame. washer washer

NOTICE: Do not start tightening the bottom bracket

with a tool. Dirt and other contaminants can
damage the threading.

3. Use the proper tool to torque both sides to

specification (see the Tool and spline compatibility SRAM GXP cranks
table below). only
4. If necessary, add spacers before installing the cranks
(see the Spacers required table at the top right).

Tool and spline compatibility

Tool Praxis Unior Park Tool Wheels Mfg CeramicSpeed
Model TP-2400 TP-3028 1671.T47 BBT-47 BBTOOL-48-44
—
Part number 594148 594147 1043614 568922 589307
24mm X X
Praxis
30mm X X
Bottom bracket
manufacturer

Wheels MFG X
SRAM DUB X X
Chris King X X
Ceramic- 24mm X X X
Speed GXP X

6
 2022 Speed Concept SLR/TT

Headset and basebar/stem

1
5 High (SLR)
4Nm 2 35mm
6
Middle (SLR)
5.2Nm 4 15mm
35mm
15mm
5mm Low (SLR)
10mm
Low (TT)
12
2Nm
7
9 8
10 SLR
SLR
9-10Nm 3
5mm
400mm
TT
11

TT

380mm

1 Bar cap plug —  W5258507 Basebar/stem maximum cut length

Do not cut the bars closer than 47mm to the slotted holes.
2 Top cap bolt
W5257464
3 Compression plug

4 Top cap —  W5258506

5 Faceplate —  W5258528 47mm

6 Stem bolts (M5x18mm) —  W582092

7 Steer stop bolt (M4x9mm) —  W546731

8 Steer stop —  W5259927

9 Split ring —  W563834

10 Upper headset bearing —  W513538

11 Lower headset bearing — W540243

Low (SLR) — W5308426

Middle (SLR) — W5308427
12 Basebar/stem
High (SLR) — W5308428
Low (TT) — W5308429

7
 2022 Speed Concept SLR/TT

Headset and basebar/stem (continued)

Cut the steerer tube (new forks only) 2. Assemble the parts as shown below.
If installing a new fork, cut the steerer tube following the 5
table below. Measure from the top of the fork crown base. Loosely
tighten 6 12
Frame Cut 9
size length
S 96mm 10
M 121mm
11
L 146mm
XL 171mm

3. Install the top cap (4) and top cap bolt (2).
2
4Nm max
4

NOTE: The steerer tube must be flush or below (0-6mm) 4. Tighten the non-driveside stem bolts (6). Then,
the top of the basebar/stem after fully installed. This tighten the driveside stem bolts (6).
measurement does not include the compression plug.
1 2
5.2Nm 5.2Nm
0-6mm (under load)

5. Remove the top cap (4), top cap bolt (2), and
compression plug (3).
TIP: Turn the bike upside down or use a pick to
remove the compression plug.
Verify the steerer tube length under load 6. Verify the steerer tube is flush or below (0-6mm) the
1. Install the compression plug. basebar/stem. Measure and cut again, if necessary.

3 0-6mm

8
 2022 Speed Concept SLR/TT

Headset and basebar/stem (continued)

Install the headset and basebar/stem

1. Clean the steerer tube using 50/50 isopropyl 4. Grease both bearings (10, 11), the fork crown race,
alcohol/water mix. and both head tube bearing bores (upper and lower).
2. Install the steer stop. 10
11
2Nm 7

5. Insert the fork into the head tube. Route the

split ring (9) down the brake hoses and wire (if Di2).
3. Install the compression plug with the arrow facing
forward. Di2 example
3
9-10Nm

Rear
brake

Shift wire
(Di2 only) Front
brake

NOTE: The Di2 wire and rear brake hose can

also be routed through the non-drive side of
the split ring (9).

9
 2022 Speed Concept SLR/TT

Headset and basebar/stem (continued)

Install the headset and basebar/stem
6. Attach the faceplate (4) to the basebar/stem. Loosely 8. Tighten the non-driveside stem bolts until the
tighten the stem bolts. faceplate has a close fit with the steerer tube.
NOTICE: Do not fully torque these bolts — this will
prevent the top cap from obtaining the proper
preload.
5

6
Loosely Tighten to prevent
tighten movement

9. Install the top cap (4) and top cap bolt (2) — tighten
until play is removed. Install the bar cap plug (1).

1

2
4Nm max
7. Slide the basebar/stem onto the steerer tube. Route
both hoses as shown below. 4

Di2 example

10. Tighten the non-driveside stem bolts to 5.2Nm.

Tighten the driveside stem bolts to 5.2Nm.

1 2
5.2Nm 5.2Nm

10
 2022 Speed Concept SLR/TT

Cockpit — towers
1 25mm 35mm 40mm
5.2Nm
2

60mm 50mm
Near

Middle

Far

6.8Nm
7

0°
-7°

9
8 7°

14°
1.5Nm
10 11 +7°

25mm — W5258525 5mm fit Driveside — W5258514

5
Tower spacers Non-driveside — W5258533
1 35mm — W5258526
bolts
40mm — W5258527 0mm — W5258510

2 Bolt washers — W5258529 15mm — W5258511

Tower 30mm — W5258512
Near (driveside) — W5258521 6
bases 45mm — W5258513
Near (non-driveside) — W5258522
60mm — W5260270
Tower Middle (driveside) — W5258517
3 75mm — W5260271
toppers Middle (non-driveside) — W5258518
Far (driveside) — W5258519 7 Under tower bolt (M6x20mm) — W5258524

Far (non-driveside) — W5258520 8 Junction cover foam — W5258508

-7° (driveside) — W5258516
9 Basebar/stem foam — W5258509
Angled -7° (non-driveside) — W5258535
4
spacers +7° (driveside) — W5258515 10 Junction cover — W5257630
+7° (non-driveside) — W5258534
11 Junction cover bolt (M4x10mm) — W5258523

11
 2022 Speed Concept SLR/TT

Cockpit — aerobars
1

3 2
2Nm

4
5

5.2Nm 6

7
8 6
5.2Nm

9

10

1 Arm pads

2 Arm pad holders

W5263384
Arm pad bolts —
3
W330683
4 Arm pad washers

Driveside — W5263882
5 Bolt covers
Non-driveside — W5263883

6 Extension bolts — W5263881

7 Dogbone washer — W5263884

8 Extension base — W5258530

9 Extension bars — 5285924

10 Aerobar slide washers — W5263885

12
 2022 Speed Concept SLR/TT

Cockpit — install the towers and aerobars

1. Assemble the towers. Insert and torque the tower 3. Route the shift wires through the aerobar assembly.
topper bolts to 5.2Nm.
NOTE: Your setup may have different parts depending
on spacers and tower bases used.

5.2Nm 4. Attach the aerobar assembly to the towers. Do not

1 fully torque the bolts.

5
Loosely tighten
6

Optional spacers

2. Connect the extension bars to the extension base.

NOTICE: Do not pinch the wires. Make sure

5.2Nm all wires are tucked inside the towers and
aerobars.
6
25mm max

OPTIONAL: To shorten the extension bars, you can

cut them at the dotted lines shown above. Before
cutting, insert the extension bars into the extension
base to test the fit.

13
 2022 Speed Concept SLR/TT

Cockpit — install the towers and aerobars (continued)

5. Route the wires out the junction box cavity and seat 7. Attach the arm pad holders (2) and arm pads (1).
the aerobar assembly on the basebar/stem. Loosely OPTIONAL: For further adjustment, you can move
tighten the bolts. the arm pad holders outward using one of the
four mounting hole sets. You can also rotate the
horizontal angle of the arm pads up to 10° using the
dogbone washers (7).

7
Loosely
tighten

6. Tighten both bolts on the same side — tightening one

bolt a few turns and then the other — until they are
both torqued to 6.8Nm. Repeat for the other side and
verify all bolts are fully torqued.

6.8Nm

14
 2022 Speed Concept SLR/TT

Cockpit — install the towers and aerobars (continued)

8. Adjust the extension bars — to the rider’s fit — forward 11. Connect the wires to the junction(s) as shown below.
or backward. Insert them into the basebar/stem and attach the
junction cover.
NOTE: Di2 has two foam pieces (9) taped to the
basebar/stem and eTap has only one (more detail is
shown in the diagram on page 11).
eTap

9. Tighten both bolts on the same side — tightening one

bolt a few turns and then the other — until they are
both torqued to 5.2Nm. Repeat for the other side and
verify all bolts are fully torqued.

5.2Nm
8
10

11 1.5Nm

Di2
10. Attach the bolt covers.

8
10

11 1.5Nm

15
 2022 Speed Concept SLR/TT

Seatpost — SLR
7
1
9-11Nm
8
6

9 8-10Nm

3 5
9-11Nm
10 11
Flippable Fixed

10Nm
2
4

NOTICE: Do not apply grease to the back of the

wedge (5) where it contacts the seatpost. Only
apply grease to the parts as shown above.

7x7mm —  W524900 2 Bolt (M6x40mm)

1 Saddle ears and bolt 7x9mm —  W5256105 3 Wedge 5294346

7x10mm —  W524901 4 Wedge washer

5 IsoSpeed cover — 5302889

6 Foam piece — W5303840

7 Bolts (M6x20mm) — W5277565

Seatpost (flippable)
Short —  W5266951 8 Rubber plug — W5277955
Long —  W5266952
9 Head — W5277566

10 Barrel
W5280097
11 Titanium bolt (M6x20mm)

Seatpost (fixed) 10 Barrel

Short —  W5268027 W5280097
Long —  W5268028 11 Titanium bolt (M6x20mm)

16
 2022 Speed Concept SLR/TT

Seatpost — TT
6 1
9-11Nm
7

8 8-10Nm

5
9-11Nm 3

9 10
Flippable Fixed

10Nm
2
4

NOTICE: Do not apply grease to the back of the

wedge (5) where it contacts the seatpost. Only
apply grease to the parts as shown above.

7x7mm — W524900 2 Bolt (M6x40mm)

1 Saddle ears and bolt 7x9mm — W5256105 3 Wedge 5294346

7x10mm — W524901 4 Wedge washer

5 Wedge cover — 5303030

6 Bolts (M6x20mm) — W5277565

Seatpost (flippable) 7 Rubber plug — W5277955

Short —  W5266951
Long —  W5266952 8 Head — W5277566

9 Barrel
W5280097
10 Titanium bolt (M6x20mm)

Seatpost (fixed) 9 Barrel

Short —  W5268027 W5280097
Long —  W5268028 10 Titanium bolt (M6x20mm)

17
 2022 Speed Concept SLR/TT

IsoSpeed — SLR
NOTICE: Only authorized dealers should perform maintenance on the IsoSpeed. Improper handling, tools used, or torque
applied to these parts may result in damage to the IsoSpeed parts or cause seatpost movement.

1
9Nm
2
3
7
8
5
6.8Nm 6

9
10
Tongue

1 Pivot bolt Servicing the IsoSpeed

Contaminants can build up between IsoSpeed
2 Wave washer components causing movement and noise. To service the
IsoSpeed, follow the steps below:
3 Flat washers 5288664
1. Remove all parts shown above and clean them with
4 Pivot nut 50/50 isopropyl alcohol/water mix.
2. Apply threadlocker to the threads on the parts shown
5 Pivot sleeve below.

6 Tongue bolt — W5268219 4 1

7 Tongue T-nut — W5260276

8 Flanged bushings — W5256074

9 Tongue washer — W5260277

10 Seatmast grommet — W5260165

18
 2022 Speed Concept SLR/TT

IsoSpeed — SLR (continued)

3. Apply grease to the parts shown below.

1 6

10 2

4. Reassemble all parts. Torque the tongue bolt (6) and

pivot bolt (1) to the values shown on page 18.
5. Clean the inside of the tongue and seatmast
grommet (10) with 50/50 isopropyl alcohol/water
mix. Remove any grease that could affect the
seatpost clamp.

19
 2022 Speed Concept SLR/TT

Chainkeeper
1 Bolt (M4x22mm)

2 Chainkeeper
573827
3 Flat washer (M5x10mm)

1 4 Screw (M5x16mm)

1Nm
2

3Nm
4

Adjust the chainkeeper

1. Shift to the lowest gear (largest rear cassette cog) and inner chainring.
2. Loosen the bolt (1) on the chainkeeper.
3. Rotate the loose piece (shown in red below) so there is 1mm of horizontal clearance to the chain.

1mm

4. Tighten the bolt (1) to 1Nm.

20
 2022 Speed Concept SLR/TT

Accessories — SLR
Downtube bottle Bento box
3 1 NOTE: The removable storage box, dividers, and cover are
dishwasher safe (top rack only).
2Nm
3
1
2

1 Water bottle — W5254705

2 Water bottle cage — W5296085

2Nm
3 Bolts (M5x12mm) — W304515
4

Tool holder/flat kit W5264707

1 Cover — W5254769

1 2 Bucket — W5254770 5276409

3 Dividers — W5254771

4 Screws (M5x10mm) — W549305

1 Tool holder — W5264707

21
 2022 Speed Concept SLR/TT

Accessories — SLR (continued)

Seatpost light mount Between-the-arms bottle cage bracket

3
2

1
4-6Nm

3Nm
1

1 Bolts (M5x14mm)

2 Light bracket W5263880

3 Rubber washer

1 Bolts (M5x10mm)
W5284485
2 Bottle cage bracket

22
 2022 Speed Concept SLR/TT

Accessories — SLR (continued)

Between the arms bottle Blendr Mount

4Nm
2

1
2

3Nm 1

4
1.5Nm

3
5

6
3Nm
7
3Nm

1 Bolts (M5x10mm)

2 Bottle base

3 Straw

4 Bolt (M4x6mm)
W5269794
5 Straw clip

6 Bolt (M5x20mm)

7 Bolt (M5x25mm) 1 Bolt (M5x10mm)

5284244 (mono)
8 Bottle cage adapter 5284245 (duo)
2 Blendr Base

23
 2022 Speed Concept SLR/TT

Specifications
TT SLR
Rear hub OLD 142mm 142mm

Upper fork steerer tube OD 28.6mm 28.6mm

Lower fork steerer tube OD 38.8mm 38.8mm

Bottom bracket type/width T47/85.5mm T47/85.5mm

Brake rotor diameter min/max 140/160mm 140/160mm

45mm 45mm
(SRAM) (SRAM)
Chainline (2x)
44.5mm 44.5mm
(Shimano) (Shimano)
1x 58t 58t

2x small 47t 44t

Chainring max 55t 55t
(Shimano) (Shimano)
2x large
54t 54t
(SRAM) (SRAM)
Front 25mm 25mm
Tire width max 700c
Rear 25mm 28mm

24